For U.S.A. & Canada model

SERVICE MANUAL

Ver. 1

MODEL

DVD-5910

DVD AUDIO-VIDEO / SUPER AUDIO PLAYER

For purposes of improvement, specifications and design are subject to change without notice.

8

Please use this service manual with referring to the operating instructions without fail.

Some illustrations using in this service manual are slightly different from the actual set.

TOKYO JAPAN

X0223-1V.01 DE/CDM 0412

DVD-5910/DVD-A1XV

SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.

LASER RADIATIONDo not stare into beam or view directly with optical instruments, class 3A laser product.

500V

1M

(1)

(2)

(1) (2)

2

DVD-5910/DVD-A1XV

WIRE ARRANGEMENTIf wire bundles are untied or moved to perform adjustment or parts replacement etc.,be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation.

Wire arrangement viewed from the top

Front Panel side

3

DVD-5910/DVD-A1XV

DISASSEMBLY(Follow the procedure below in reverse order when reassembling.)

1. Top Cover(1) Remove 2 rear screws (s1) and 8 top screws (s2), then detach the Top cover. (2) Remove 2 side screws (s3) and 3 top screws (s4), then detach the Side cover(L). (3) Remove 2 side screws (s5) and 3 top screws (s6), then detach the Side cover(R).

1. Top Cover(1) s1 2 s2 8 TOP COVER (2) s3 2 s4 3 SIDE COVER(L) (3) s5 2 s6 3 SIDE COVER(R)

4

DVD-5910/DVD-A1XV

2. Front Panel sub Assy2.1. When the Disc tray can be ejected electrically.(1) Switch on, and press [OPEN/CLOSE] button to open the Disc tray. (2) Detach the Loader panel ass'y (c1) by lifting. (3) Close the Disc tray. (4) Disconnect the wires [CX026] [CX035] from the Front panel sub ass'y (a1). (5) Remove 4 top screws (s1) and 4 bottom screws (s1), then detach the Front panel sub ass'y (a1). (6) Disconnect the FFC [CX211] from the Front panel sub ass'y (a1). (7) Remove 4 top screws (s2), then detach the Angle (m1). (Note: This Angle provide on Front and Rear.) (8) Remove both 2 top screws (s3) and (s4), then detach the Angle (m2). (Note: The 2 top screws of s4 provide only Japan model.)

2. Front Panel sub Ass'y2.1. (1) OPEN/CLOSE (2) c1Loader panel ass'y (3) (4) a1Front panel sub ass'y [CX026] [CX035] (5) s1 4 a1Front panel sub ass'y (6) a1Front panel sub ass'y FFC[CX211] (7) s2 4 m1Angle 2 (8) s3 2 s4 2 ( s3 2 )m2Angle

2.2. When the Disc tray cannot be ejected electrically.(1) Insert a driver into the side hole of DVD Mechanism, and push the Plate Gear of the DVD Mechanism, to open the Disc Tray. (Arrow direction) (2) The same steps described on 2-1.(2)~(8).

2.2. (1) ( ) (2) 2-1.(2) (8)

5

DVD-5910/DVD-A1XV

3. DVD mechanism Assy(1) Remove 4 top screws (s1). (2) Disconnect the wires [CY251] [CY301] [CY171] [CX331] [CY101] connecting the MAIN P.W.B.(GU-3618). (3) Detach the DVD mechanism ass'y.

3. DVD mechanism Ass'y(1) s1 4 (2) (GU-3618) [CY251] [CY301] [CY171][CX331] [CY101] (3) DVD mechanism ass'y

4. Analog Power unit / Power trans4.1. Power trans(1) Disconnect the wire [CX025] connecting Digital Power unit(GU-3656-2). (2) Disconnect the wire [CX062] connecting Analog Power unit(GU-3656-1). (3) Remove 2(Japan: 4) top screws (s1). (4) Detach the Power trans (m1).

4. Analog Power unit / Power trans4.1. Power Trans(1) Digital Power unit(GU-3656-2) [CX025] (2) Analog Power unit(GU-3656-1) [CX062] (3) s1 2 ( 4 ) (4) m1:Power trans

4.2. Analog Power unit(1) Disconnect the wire [CX031] [CX032] [CX042] [CX037] connecting Analog Power unit(GU-3656-1). (2) Remove 4 top screws (s2), then detach the Analog Power unit (u1). (3) Remove 4 top screws (s3), then detach the Shield plate (m2).

4.2. Analog Power unit(1) Analog Power unit(GU-3656-1) [CX031][CX032][CX042][CX037] (2) s2 4 u1:Analog Power unit (3) s3 4 m2:Shield Plate

6

DVD-5910/DVD-A1XV

5. Digital Power unit5.1. Digital Power unit(1) Remove 2 side screws (s1). (2) Disconnect the wires [CX024] [CX081] [CX101] [CX121] [CX063] connecting Digital Power unit. (3) Remove 4 top screws (s2), then detach the Digital Power unit (u1).

5. Digital Power unit5.1. Digital Power unit(1) s1 2 (2) Digital Power unit [CX024][CX081][CX101][CX121][CX063] (3) s2 4 u1:Digital Power unit

5.2. 1.5V Power unit(1) Remove 2 rear screws (s3). (2) Disconnect the wire [CX059] connecting 1.5V Power unit. (3) Remove 1 top screw (s4), then detach the 1.5V Power unit (u2). (4) Remove 2 rear screws (s5), then detach the AC Inlet (m1).

5.2. 1.5V Power unit(1) s3 2 (2) 1.5V Power unit [CX059] (3) s4 1 u2:1.5V Power unit (4) s5 2 m1:AC Inlet

6. Video Unit(1) Disconnect the wire [CY059] connecting the I/P unit, the FFC [CY331] and the wires [CY081] [CX031] [CX102] connecting the Video2 unit, the FFC [CX174] connecting the Video1 unit. (Note: The wire [CX102] only Europe & China model.) (2) Remove 9 screws (s1), 6 screws (s2), 2 screws (s3) and 1 screw (s4) on the rear side. (Note: The 1 screw of s4 provide only Japan model.) (3) Remove 2 top screws (s5), then detach the Video unit.

6. Video unit(1) I/P unit [CY059]Video2 unit FFC[CY331] [CY081],[CX031](E2E1C [CX102])Video1 unit FFC[CX174] (2) s1 9 s2 6 s3 2 ( s4 1 ) (3) s5 2 Video unit

7

DVD-5910/DVD-A1XV

7. IEEE1394 unit / System unit7.1. IEEE1394 unit(1) Disconnect the FFCs [CY191] [CY173] from the IEEE1394 unit. (2) Remove 2 rear screws (s1) and 1 side screw (s2). (3) Remove Locking Card Spacer, then detach the IEEE1394 unit.

7. IEEE1394 unit / System unit7.1. IEEE1394 unit(1) IEEE1394 unit FFC[CY191][CY173] (2) s1 2 s2 1 (3) Locking Card Spacer IEEE1394 unit

7.2. System unit(1) Remove 2 top screws (s3), then detach the EMC Angle (m1). (This EMC Angle provide only U.S.A. & Canada model.) (2) Remove 4 top screws (s4), then detach the Mecha Base (m2). (3) Remove 2 screws (s5), 2 screws (s6) on the rear side. (4) Remove 6 top screws (s7), then detach the System unit.

7.2. System unit(1) s3 2 m1:EMC Angle (EMC Angle E3 ) (2) s4 4 m2:Mecha Base (3) s5 2 s6 2 (4) s7 6 System unit

8

DVD-5910/DVD-A1XV

8. SCART unit / Audio unit8.1. SCART unit (for Europe & China model only.)(1) Remove 2 rear screws (s1), then detach the SCART unit (u1).

8. SCART unit / Audio unit8.1. SCART unit (E2,E1C )(1) s1 2 u1:SCART unit

8.2. Mix Audio unit(1) Disconnect the FFC [CY192] and the wire [CX053] [CY042] from the Mix Audio unit (u2). (2) Remove 2 screws (s2), 2 screws (s3) on the rear side. (3) Remove 4 top screws (s4), then detach the Mix Audio unit (u2).

8.2. Mix Audio unit(1) u2:Mix Audio unit FFC[CY192] [CX053][CY042] (2) s2 2 s3 2 (3) s4 4 u2:Mix Audio unit

8.3. 5.1Ch Audio unit(1) Remove 6 rear screws (s5). (2) Remove 4 top screws (s6), then detach the 5.1ch Audio unit (u3).

8.3. 5.1Ch Audio unit(1) s5 6 (2) s6 4 u3:5.1ch Audio unit

9

DVD-5910/DVD-A1XV

9. I/P unit9.1. Support bracket(1) Remove 2 top screws (s1) and 3 side screws (s2), then detach the Support bracket (m1).

9. I/P unit9.1. Support bracket(1) s1 2 s2 3 m1:Support bracket

9.2. I/P unit(1) Release the I/p unit (u1) from 2 Locking card spacers. (2) Disconnect the wire [Board to Board], then detach the I/P unit (u1) to the arrow direction.

9.2. I/P unit(1) c1:Locking card spacer 2 (2) Board to Board u1:I/P unit

10. Video unit10.1. Video 1 unit(1) Remove 3 top screws (s1). (2) Release the Video 1 unit (u1) from 2 Locking card spacers. (3) Disconnect the wire [Board to Board], then detach the Video 1 unit (u1) to the arrow direction.

10. Video unit10.1. Video1 unit(1) s1 3 (2) c1:Locking card spacer 2 (3) Board to Board u1:Video1 unit

10.2. Support Bridge(1) Turn over the unit. (2) Detach 2 Locking card spacers (c2). (3) Remove 3 top screws (s2). (4) Remove 1 side screw (s3), then detach the Support bridge (m1).

10.2. Support Bridge(1) (2) c2:Locking card spacer 2 (3) s2 3 (4) s3 1 m1:Support bridge

10

DVD-5910/DVD-A1XV

Iop Measurement (Judging for Traverse Unit Replacement)As to deciding whether optical pickup is defect or not (for replacing traverse unit), follow the steps below.

Iop

1. Judging Step(1) Disc play abnormal Problems such as disc no read, unsteady playback, etc. (2) Laser drive current (Iop) check. Check Iop according to the measuring method described in step 2 below. If the checked value is 1.5 times or more than the initial Iop indicated on the rear of mechanism unit, the traverse unit should be replaced. (3) Replacing traverse unit Referring to How to Replace Traverse Unit, replace the traverse unit. No mechanism adjustment is required as the whole unit is replaced with a new one.DVD CD

1. (1) (2) Iop 2 Iop 1.5 (3) mA mADVD CD

mA mA

Laser current initial value on the rear of mechanism

Laser current initial value on the rear of mechanism

2. Iop Measuring MethodDVD laser drive current measuring points [DVD] Iop silk point

2. Iop DVD laser drive current measuring points [DVD] Iop silk point

CD laser drive current measuring points [CD] Iop silk point

GU-3618 P.W.B. (foil side)

CD laser drive current measuring points [CD] Iop silk point

GU-3618 P.W.B. (foil side)

(1) DVD laser drive current measurement Playback the title-1/chapter-1 of DVDT-S01 or commercially available DVD disc. Connect an oscilloscope to the test point above and measure the voltage. DVD laser drive current is calculated by: Iop = Measured Voltage Value / 14 (Resistance Value) (2) CD laser drive current measurement Playback the track-1 of TCD-784 or commercially available CD disc. Connect an oscilloscope to the test point above and measure the voltage. CD laser drive current is calculated by: Iop = Measured Voltage Value / 12 (Resistance Value)

(1) DVD DVDT-S01 DVD 1 1 DVD = /14 (2) CD TCD-784 CD 1 CD = /12

11

DVD-5910/DVD-A1XV

Diagnostics of Optical Pickup and Replacing Traverse Unit1. Note for Handling the Laser Pick-upThe protection for the damage of laser diode. If you want to change the optical device unit from any other units, you must keep the following. (1) It should be done at the desk already took measures the static electricity in care of removing the OPUs (Optical deice unit) connector cable. (2) Workers should be put on the Earth Band. (3) It should be done to add the solder to the short land to prevent the broken Laser diode before removing the 24P FFC cable. (4) Dont touch OPUs connector parts carelessly.

1. (1) (2) (3) (4) 24P FFC

2. Optical Pick-up Diagnostics and ReplacementWhen repairing, carry out failure diagnostics by following the procedure described below. If the present value of the laser drive current is 150% up to initial value, it is the point of the pickup replacement. In case of the pickup replacement, replace the Traverse Unit with no adjustment. The initial value is indicated on the label on back side of Mecha.

2. 150%

NO DISC indicated, Playback not smooth, etc.

"NO DISC"

Laser drive current check HF signal check Present value: 150% up to initial value

HF 150%

Traverse Unit replacement (refer to page 13) (13

Laser drive current check after replacement. If the present value is less than 80mA, write on the new label by hand, put on the new label over the old label. If the present value exceeds 80mA,replace the Traverse Unit with a new one. Cause : Damaged electrostatically when replaced.

80mA

80mA

12

DVD-5910/DVD-A1XV

How to Replace Traverse Unit1. Preparing for Replacement(1) Removing Clamp Base Damper Remove 4 pcs of 2.6mm machine screw (a), and detach the Clamp Base Damper upward. (2) Removing Clamp Base Remove 6 pcs of 3mm P-tight screw (b), and detach the Clamp Base upward. (3) Ejecting Loader Through the left rectangular hole of the Mechanism Unit, push the slider with a ruler or driver unit the Traverse portion lowers and the Loader comes out a little. (4) Removing Loader Remove 2 pcs of 3mm P-tight screw (c) on the Loader Holder left. Remove 2 pcs of 3mm P-tight screw (d) on the Loader Holder right, then pull up the Bearing Plate. Fully pull out the Loader forward, and lift up to take it out. (5) Shorting Pickup To protect the Pickup from static electricity, short-circuit 2 positions as shown in figure. (6) Removing Main P.W.B. Assy Remove 4 pcs of 3mm P-tight screw (e), and detach the Main P.W.B. Assy downward.(a)Clamp Base Damper

1. (1) 2.6mm (a) 4 (2) 3mmP (b) 6 (3) (4) 3mmP (c) 2 3mmP (d) 2 (5) 2 (6) ASS'Y 3mmP (e) 4 (c)

(a)

(b)

Clamp Base

(b)

(d) (c)Holder

Bearing Plate

(d)

Loader

A

A

(4) (3)Main P.W.B. Assy

(4) (3) Ass'y

Solder to short-circuit (CD)

(CD)

(e)Solder to short-circuit (DVD) Short-circuit with solder (enlarged fig. A)

(e) (DVD)

2. Replacing Traverse Unit(1) Removing Wires CX241: 24P-FFC for Pickup CX151: 15P-FFC for Spindle CX031: 3P-PH wire for PU Side (2) Removing Traverse Unit Remove 4 pcs of special screw (f) and dampers, then take out the Traverse Unit upward. (3) Mounting Traverse Unit Mount the Traverse Unit following the reverse order.

2. (1) (f)Traverse Unit

CX241 24P-FFC CX151 15P-FFC CX031PU 3P-PH (2) (f) 4 4 (3)

(f)

Damper

13

DVD-5910/DVD-A1XV

3. Installing Loader(1) Inserting Loader Set and push the Loader to the arrow direction until it stops. When installing the Loader, move Plate Gear to right beforehand so as that the boss of the Plate Gear fits in the backside groove of the Loader. (See figure right) (2) Fixing Loader Fix the Loader with each 2 screws (c) and (d).Plate Gear

3. (1) (2) (c)(d) 2

Groove

Boss

(d)

(d)

Bearing Plate

(c)Loader

(c)

4. Assembly (1)(1) Assembling Main P.W.B. Assy Fix the Main P.W.B. Assy with 4 pcs of 3mm P-tight screw (e). (2) Removing Pickup-short Solder After connecting 24P-FFC of the Pickup with P.W.B., remove solder from 2 shorted positions. (3) Temporary Positioning Clamp Base To protect your eyes from laser light, put the Clamp Base temporarily. (4) Positioning up Traverse Unit Connect the following wires of the Mechanism Unit, and operate it. CX141: 14P-PH wire for power CX131: 13P-FFC wire from Display P.W.B. Turn on the power to the unit, and press OPEN/CLOSE button to close the Loader. The Traverse Unit rises up. (display: 0h00m00s) Pull out Loader forward, and life up to take it out.

4. 1(1) ASS'Y 3mm P (e) 4 Clamp Base

(2) 24PFFC 2 (3) (4) CX141 14P-PH CX131 13P-FFC CLOSE (0h00m00s

(e)Main P.W.B. Assy

(e) Ass'y

14

DVD-5910/DVD-A1XV

5. Assembly (2)(1) Attaching Tape to Clamp Base Damper Attach acetate cloth tape to 3 projections of the Clamp Base Damper backside. (2) Assembling Clamp Base Set the Clamp Base Damper with positioning for clamper by 3 projections. Fix the Clamp Base with 6 pcs of 3mm -tight screw (b).Acetate Cloth Tape Clamp Base Damper

5. 2(1) 3 (2) 3 3mmP (b) 6

Clamp Base Damper

(b)Clamp Base

(b)

6. Assembly (3)(1) Detaching Tape from Clamp Base Damper Detach acetate cloth tape from 3 projections of the Clamp Base Damper backside. (2) Assembling Clamp Base Damper Set the Clamp Base Damper to the Clamp Base contrary to the direction set in step above. Fix the Clamp Base Damper with 4 pcs of 3mm S-tight screw (a).

6. 3(1) 3 (2) 3mmS (a) 4 (a)

(a)

Clamp Base Damper

15

DVD-5910/DVD-A1XV

SERVICE MODE1. Aging Mode(1) preparation(a) Equipment used: Any one of DVD Karaoke Disc (containing more than 10 titles). (b) Unit setting : No spec other than the following procedure (Aging mode). At the tray open status, press the POWER button to turn on the power while pressing the PLAY and OPEN/CLOSE buttons for DVD operation simultaneously. mark on the FL lights, and the unit is set to the heat run mode.

1. (1) (a) DVD 10 (b) DVD + / FL

(2) procedure(a) According the above, set to the aging mode. (b) Set a DVD Karaoke disc to the tray and press the PLAY button once. mark on the FL blinks, and aging operation(after playback title-1 and title-10 of the disc, the tray open/close is made automatically, then playback the title-1 again) starts. This aging operation continues automatically until it is stopped or it stops caused by an error. In case of some error in DVD, the following error messages are displayed on the FL.

(2) (a) (b) DVD 1 FL 1 10 / 1 DVD FL

No 1 2 3 4 5 6 7 Bad Disc Focus Error Read Error Tracking Error Tray Error

Error contents

FL display ERROR 02 ERROR 04 ERROR 03 ERROR 04 ERROR 05 ERROR 06 ERROR07

No.1 2 3 4 5 6 7

FL ERROR 02 ERROR 04 ERROR 03 ERROR 04 ERROR 05 ERROR 06 ERROR 07

Navigation Pack Read Error Cmmunication Error

2. Initial Setting Mode(1) Preparation(a) Equipment used: None (b) Unit setting: No spec other than the following procedure

2. (1) (a) (b)

(2) Procedure(a) Initialize the DVD player when com, peripheral parts of com, or Main P.W.B. has been replaced in servicing. (b) Carry out the following to restore factory setting mode. At the player stop condition, press 3 buttons for DVD operation(PLAY,OPEN/CLOSE, and SKIP) until INITIALIZE appears and disappears in the FL. (Initialized appears and disappears on the TV screen.) (c) All user setting will be lost and its factory setting will be restored when this initialization is made. Be sure to memorize your setting for restoring again after the initialization.

(2) (a) (b) + / + ( 3 "INITIALIZE" (c)

16

DVD-5910/DVD-A1XV

3. com Firm Check Mode(1) Preparation(a) Equipment used: None (b) Unit setting: No spec other than the following procedure.

3. (1) (a) (b)

(2) Procedure(a) Press the POWER button to turn on the power while pressing the PLAY and OPEN/CLOSE buttons for DVD operation simultaneously. (b) FL all light mode. This mode is for detecting FL defects. Press STILL/ PAUSE on the remote control unit once to light all FL segments. (c) DVD com and main unit com firm check mode. This mode is for displaying the status of each com employed. Push remote countroller 3265 DVD com firm: Press the MENU button . Each time the MENU button on the remote control unit is pressed, com firm is displayed one after another.B/E com MAKE DAY Drive com SYSTEM com Scaler DSP IEEE 1394 ESS 6780 MAKE DAY C10 DRV 030 825 SYSTEM 6867 SCALER 0A02 DSP 6790 C 20041028

(2) (a) / (b) / (c) 3265

B/E DSP IEEE 1394

ESS 6780 MAKE DAY C10 DRV 030 825 SYSTEM 6867 SCALER 0A02 DSP 6790 C 20041028

17

DVD-5910/DVD-A1XV

TROUBLE SHOOTING1. GU-3618 (MAIN UNIT), GU-3653-1 (SYSTEM UNIT)1.1. FL TUBE dosen't light(1) Check the Set-up process of System -COM Check Power Supply Voltages. GU-3653-1(SYSTEM UNIT) [IC104]:D1,D4 +3.3V_D1,+3.3V_NSW

1. GU-3618 (MAIN UNIT) , GU-3653-1 (SYSTEM UNIT)1.1. FL (1) -COM GU-3653-1(SYSTEM UNIT) [IC104]:D1,D4 +3.3V_D1,+3.3V_NSW

N.G.

Check Soldering. CY121 on SYSTEM UNIT.

N.G.

SYSTEM UNIT CY121

O.K.Check Oscillation waveform. GU-3653-1(SYSTEM UNIT) [IC104]: 16MHz at 13pin.

O.K. GU-3653-1(SYSTEM UNIT) [IC104]: 16MHz at 13pin.

N.G.

Check Soldering. X101 on SYSTEM UNIT.

N.G.

SYSTEM UNIT X101

O.K.Check Power Supply Voltages. GU-3653-1(SYSTEM UNIT) [IC104]: "H"level at 39pin?"L"level at 7pin and 44pin?

O.K. GU-3653-1(SYSTEM UNIT) [IC104]: "H"level at 39pin?"L"level at 7pin and 44pin?

N.G.

Check Soldering. IC104 on SYSTEM UNIT.

N.G.

SYSTEM UNIT IC104

O.K.Check Reset Signal GU-3653-1(SYSTEM UNIT) [IC104]: "H"level at 10pin?

O.K.RESET GU-3653-1(SYSTEM UNIT) [IC104]: "H" level at 10pin?

N.G.

Check Soldering. IC103(Reset IC) on SYSTEM UNIT.

N.G.

SYSTEM UNIT IC103(Reset IC)

O.K.Check Data Bus between GU-3656-3(DISPLAY UNIT) FLD Driver(GU-3656-3(IC101) [VFD_RST]:"H"level?

O.K. GU-3656-3(DISPLAY UNIT) FLD Driver(GU-3656-3(IC101)] [VFD_RST]:"H"level?

N.G.

(1) Check soldering of CY211 on SYSTEM UNIT. (2) GU-3656-3 is N.G.(No Good).

N.G.

(1) SYSTEM UNIT CY211 (2) GU-3653-3

O.K.Continue to next step. Check the Set-up process of B/E -COM.

O.K. (2) B/E -COM

18

DVD-5910/DVD-A1XV (2) Check the Set-up process of B/E -COM Check Power Supply Voltages. GU-3618(MAIN UNIT) [IC108]:D1,D4 +3.3V_ESS,+2.0V_ESS O.K.?

(2) B/E -COM GU-3618(MAIN UNIT) [IC108]:D1,D4 +3.3V_ESS, +2.0V_ESS

N.G.

Check the output level. [ON/ST] : "H" level?

N.G.

Check Soldering. GU-3653-1(SYSTEM UNIT) [IC104]:88pin.

N.G.

[ON/ST] : "H" level?

N.G.

GU-3653-1(SYSTEM UNIT) [IC104]:88pin.

O.K.Check Clock waveform. GU-3618(MAIN UNIT) [IC108]:49,108,116pin and 117pin. 27MHz (3.3V), O.K.?

O.K.

N.G.

Check 27MHz (3.3V) at 10pin of IC106.

N.G.

(1) Check Soldering of X101. (2) Check Soldering of IC105 (SM8701).

GU-3618(MAIN UNIT) [IC108]:49,108,116pin and 117pin. 27MHz (3.3V)

N.G.

[IC106]:10pin

N.G.

(1) [X101] (2) [IC105](SM8701).

O.K. O.K.

Check Soldering. Of R114,R115 and R154.

O.K. O.K.

R114,R115 and R154.

Check Reset signal. GU-3618(MAIN UNIT) [IC108]:(RESET)24 pin. "H" level O.K.?

N.G.

Check Soldering. GU-3653-1(SYSTEM UNIT) [IC104]:81pin.

RESET GU-3618(MAIN UNIT) [IC108]:(RESET)24 pin. "H" level

GU-3653-1(SYSTEM UNIT)

N.G.

[IC104]:81pin.

GU-3618(MAIN UNIT) [IC117]:5pin and 6pin. FB127 and R138.

GU-3618(MAIN UNIT) [IC117]:5pin and 6pin. FB127 and R138.

O.K.Check I2C Signal. GU-3618(MAIN UNIT) [IC108]: "H" level at 160pin and 161pin.

O.K.Check Soldering. GU-3618(MAIN UNIT) [IC108] and [IC116] R185,R186,R757,FB173 and FB174.

N.G.

IC GU-3618(MAIN UNIT) [IC108]: "H" level at 160pin and 161pin.

N.G.

GU-3618(MAIN UNIT) [IC108] and [IC116] R185,R186,R757,FB173 and FB174.

O.K.Check Address, Data Bus between GU-3618(MAIN PWB)[1C108]and[IC104](Flash Rom).

O.K.Check Soldering at Address, Data Bus,Control Signal. GU-3618(MAIN UNIT) [LD0-LD7],[LCS3,LOE]

N.G.

[1C108] [IC104](Flash Rom) GU-3618(MAIN UNIT)

N.G.

GU-3618(MAIN UNIT) [LD0-LD7],[LCS3,LOE]

O.K.Continue to next step. Check the Set-up process of F/E -COM.

O.K. (3) F/E -COM

19

DVD-5910/DVD-A1XV (3) Check the Set-up process of F/E -COM Check Power Supply Voltages. GU-3618(MAIN UNIT) [IC507]: +3.3V_D2,+1.8V_D2 O.K.? +3.3V_A2, +1.8V_A2 O.K.?

(3) F/E -COM GU-3618(MAIN UNIT) [IC507]: +3.3V_D2, +1.8V_D2 O.K.? +3.3V_A2, +1.8V_A2 O.K.?

N.G.

Check Soldering. [IC951] FB953,FB960 and FB967

N.G.

[IC951] FB953,FB960 and FB967

O.K.Check Clock waveform. GU-3618(MAIN UNIT) [IC507]:33pin. 33.87MHz (3.3V), O.K.?

O.K.Check Soldering. [IC106]:12pin R147 [IC404],R440 and R623

N.G.

GU-3618(MAIN UNIT) [IC507]:33pin. 33.87MHz (3.3V), O.K.?

N.G.

[IC106]:12pin R147 [IC404],R440 and R623

O.K.Check Reset Signal. GU-3618(MAIN UNIT) [IC507]:(DRVRST)51pin "H" level O.K.?

O.K.Check Soldering. [IC108]:145pin R618 and R628

N.G.

RESET GU-3618(MAIN UNIT) [IC507]:(DRVRST)51pin "H" level O.K.?

N.G.

[IC108]:145pin R618 and R628

O.K. END

O.K.

1.2. Image is not displayed. (Blue-back, DENON wallpaper)Check Digital output signal for Video. [1] GU-3618(MAIN UNIT) [IC108]:PCLKG [IC108]:HSYNC,VSYNC [IC108]:YUV(0-7)

1.2. DENON [1] GU-3618(MAIN UNIT) [IC108]:PCLKG [IC108]:HSYNC,VSYNC [IC108]:YUV(0-7)

N.G.

Check Soldering. [IC108]:117pin,[IC105],R115 and R120 [IC108]:118,119pin [IC108]:106-110,113-115pin,RA108,RA109

N.G.

[IC108]:117pin,[IC105],R115 and R120 [IC108]:118,119pin [IC108]:106-110,113-115pin,RA108,RA109

O.K.Check Digital output signal for Video. [2] GU-3618(MAIN UNIT) [CX331]:CLKO(13pin) [CX331]:HSYNC,VSYNC(23,24pin) [CX331]:PC2-PC9(4-11pin)

O.K.Check Soldering. [CX331]:13pin,R703,FB111 [CX331]:23,24pin,FB116,FB117 [CX331]:4-11pin,FB103-110.RA703,RA704

N.G.

[2] GU-3618(MAIN UNIT) [CX331]:CLKO(13pin) [CX331]:HSYNC,VSYNC(23,24pin) [CX331]:PC2-PC9(4-11pin)

N.G.

[CX331]:13pin,R703,FB111 [CX331]:23,24pin,FB116,FB117 [CX331]:4-11pin,FB103-110.RA703,RA704

O.K.Continue to the check process of GU-3654-1 VIDEO UNIT.

O.K.GU-3654-1 VIDEO UNIT

20

DVD-5910/DVD-A1XV

1.3. Does not Read Disc [No Play], [00 00] displayed etc.(1) Disc does not Rotate.(1) Check Soldering of P.U. short-circuit? (2) Check the circumference soldering of TR501 and TR502. (3) Check connector insertion. [P.U.] - [GU-3618] FFC(CX241) (4) Check the soldering [IC502](CXD1881AR) and circumference soldering of [IC502]. (5) Check the soldering [IC503](FAN8042) and circumference soldering of [IC503].

1.3. [No Play], [00 00] (1) Pick-up GU-3618(MAIN UNIT) P.U. O.K.?

Check the Emission of Pick-up. GU-3618(MAIN UNIT) Emission of P.U. laser O.K.? See attached sheet laser current check.

N.G.

(1) P.U. (2) TR501,TR502 (3) [P.U.] - [GU-3618] FFC(CX241)

N.G.

(4) [IC502] (5) [IC503]

O.K. GU-3618(MAIN UNIT)

O.K. Check Spindle drive signal. GU-3618(MAIN UNIT) [DMO] : "H" level?

N.G.

N.G.

(1) Check soldering of [IC507]:111-113pin. (2) Check the circumference soldering of [SPWM1],[SPWM2] and [FG] signal. (3) Check the soldering [IC501](AN8471SA) and circumference soldering of [IC501].

[DMO] : "H" level?

(1) [IC507]:111-113pin (2) [SPWM1],[SPWM2],[FG] (3) [IC501]

O.K.

O.K.

END

(2) CD check process Check the RF signal. GU-3618(MAIN UNIT) Check the voltage of Test-Point(TP) TP[RFAC]:about 1.0Vp-p

(2) CD

N.G.

(1) Check the circumference soldering of [IC502] (2) Check the circumference soldering of [IC507]

RF GU-3618(MAIN UNIT) (TP) TP [RFAC] : 1.0Vp-p

N.G.

(1) [IC502] (2) [IC507]

O.K. Check Bus Line. GU-3618(MAIN UNIT) [IC507] [IC505](16MDRAM) "L" "H" alternate?

O.K.

N.G.

Check Soldering Address,Data Bus,Control Signal. [BD0-15],[BA0-9],[XLCAS],[XUCAS],[XMOE],[XRAS] Check the circumference soldering of [IC505]

GU-3618(MAIN UNIT) [IC507] [IC505](16MDRAM) "L" "H"

N.G.

[BD0-15] [BA0-9] [XLCAS] [XUCAS] [XMOE] [XRAS] [IC505]

O.K.

O.K.

END

(3) DVD check process Check VSTEM communication. GU-3618(MAIN UNIT) [VDT07_COR],[XHAC_COR],[XSHD_COR], [DCK_COR],VEFG_COR] "L" "H" alternate?

(3) DVD

N.G.

Check Soldering. [IC507]:36-49pin R638-R650

GU-3618(MAIN UNIT) [VDT0-7_COR], [XHAC_COR],[XSHD_COR], [DCK_COR], VEFG_COR] "L" "H"

N.G.

[IC507]:36-49pin R638-R650

O.K. Check Request signal. GU-3618(MAIN UNIT) Request from [B/E] and [F/E] [HDRQ_COR]:"L"level?

O.K.

N.G.

Check the circumference soldering of [IC401]

GU-3618(MAIN UNIT) [B/E] [F/E] [HDRQ_COR] : "L" level?

N.G.

[IC401]

O.K.

O.K.

END 21

DVD-5910/DVD-A1XV(4) SACD check process (4) SACD GU-3618(MAIN UNIT) [IC401],[IC403],[IC405]: +5V_A2, +3.3V_D2, +2.5V_D2 O.K.?

Check Power Supply Voltages. GU-3618(MAIN UNIT) [IC401],[IC403],[IC405]: +5V_A2, +3.3V_D2, +2.5V_D2 O.K.?

N.G.

Check Soldering. [IC950] FB952,FB956

N.G.

[IC950] FB952,FB956

O.K.Check Clock waveform. GU-3618(MAIN UNIT) [IC401](EPM3128ATC):87pin. [IC405](CXD2753R):11pin. 33.87MHz (3.3V), O.K.?

O.K.Check Soldering. [IC401]:87pin,R498,[IC404],R440 [IC405]:11pin,R439,[IC404]

N.G.

GU-3618(MAIN UNIT) [IC401](EPM3128ATC):87pin. [IC405](CXD2753R):11pin. 33.87MHz (3.3V), O.K.?

N.G.

[IC401]:87pin,R498,[IC404],R440 [IC405]:11pin,R439,[IC404]

O.K.Check Reset signal. GU-3618(MAIN UNIT) [IC401]:(XRST_PLD)89 pin. [IC405]:(RST)9 pin. "H" level O.K.?

O.K.Check Soldering. [IC508],R413 R463

N.G.

RESET GU-3618(MAIN UNIT) [IC401]:(XRST_PLD)89 pin. [IC405]:(RST)9 pin. "H" level O.K.?

N.G.

[IC508],R413 R463

O.K.Check Bus Line. GU-3618(MAIN UNIT) [IC405] [IC402](16MSDRAM) "L" "H" alternate?

O.K.Check Soldering. Address, Data Bus, Control Signal. [DQ0-7], [D_MA0-11], [DCLK], [DCKE], [DWE], [DCAS], [DRAS] RA401-RA405,R445-R449

N.G.

GU-3618(MAIN UNIT) [IC405] [IC402](16MSDRAM) "L" "H" alternate?

N.G.

Address, Data Bus, Control Signal. [DQ0-7], [D_MA0-11], [DCLK], [DCKE], [DWE], [DCAS], [DRAS] RA401-RA405,R445-R449

O.K.Check VSTEM communication. GU-3618(MAIN UNIT) [SD0-7], [XSAC], [XSHD2], [SDCK], [SDEF], [XSRQ] "L" "H" alternate?

O.K.

N.G.

Check Soldering. [IC401]:35-37,44-48,54,63,67-69pin [IC405]:164-176pin

VSTEM GU-3618(MAIN UNIT) [SD0-7], [XSAC], [XSHD2], [SDCK], [SDEF], [XSRQ] "L" "H" alternate?

N.G.

[IC401]:35-37,44-48,54,63,67-69pin [IC405]:164-176pin

O.K.Check RF signal for Water Mark. GU-3618(MAIN UNIT) TP [WM] : about 1.0Vp-p

O.K.

N.G.

Check the circumference soldering of [IC403] (AD8062) and [IC405]:126pin

GU-3618(MAIN UNIT) TP[WM] : t 1.0Vp-p

N.G.

[IC403](AD8062) [IC405]:126pin

O.K. END

O.K.

22

DVD-5910/DVD-A1XV

1.4. No Sound,Noise generated(1) CD, DVD-VIDEO/AUDIO Check PCM Digital Audio Data (VSTEM data) and VSTEM communication. GU-3618(MAIN UNIT) [IC401]output and [IC108](ES6138)input: [BD0-7], [BSDCLK], [SHAK],[BDEF],[BSHD],[BSREQ] "L" "H" alternate?

1.4. (1) CD, DVD-VIDEO/AUDIO Check Soldering. [IC401]:75-98pin R401-R412,R494 [IC108]:122-128,131,132,142,144,149,150pin

N.G.

PCM /VSTEM GU-3618(MAIN UNIT) [IC401] / [IC108](ES6138) : [BD0-7], [BSDCLK], [SHAK], [BSDEF], [BSHD],[BSREQ] "L" "H" ?

N.G.

[IC401]:75-98pin R401-R412,R494 [IC108]:122-128,131,132,142,144,149,150pin

O.K.

O.K.Check PCM Digital Audio Data output. [1] GU-3618(MAIN UNIT) [IC108]output and [IC801](SM5819A)input: [TSD0-2],[TBCK],[TWS],[PMCK]

Check Soldering.

N.G.

[IC108]:33,36,37,40,32pin R129-R132,R134 [IC801]:29,31-35pin [IC110].R150,R157,R173

PCM [1] GU-3618(MAIN UNIT) [IC108] / [IC801](SM5819A) : [TSD0-2],[TBCK],[TWS],[PMCK]

N.G.

[IC108]:33,36,37,40,32pin R129-R132,R134 [IC801]:29,31-35pin [IC110].R150,R157,R173

O.K.Check PCM Digital Audio Data output. [2] GU-3618(MAIN UNIT) [IC801]output: [TSD0-2.],[TBCK.],[TWS.],[PMCK.] [IC801]:4pin(SELEXT)"H"?

O.K.PCM [2] GU-3618(MAIN UNIT) [IC801] : [TSD0-2.],[TBCK.],[TWS.],[PMCK.] [IC801]:4pin(SELEXT)"H"?

N.G.

Check Soldering. [IC801]:17,19-23pin R806-R811 [IC801]:4pin,[IC115]:12pin

N.G.

[IC801]:17,19-23pin R806-R811 [IC801]:4pin,[IC115]:12pin

O.K.

O.K.Check PCM Digital Audio Data output.[3] GU-3618(MAIN UNIT) Audio selector input/output: [PDATA0-2],[PBCK],[PLRCK],[PMCK] [IC124,IC125]:1pin(DSD_SEL)"L"?

PCM [3] GU-3618(MAIN UNIT)

N.G.

Check the circumference soldering of [IC124] and [ic125]

[PDATA0-2],[PBCK],[PLRCK],[PMCK] [IC124,IC125]:1pin(DSD_SEL)"L"?

N.G.

[IC124] [IC125]

O.K.

O.K.GU-3653-1 SYSTEM UNIT/GU-3655-1 AUDIO UNIT

Continue to the check process of GU-3653-1 SYSTEM UNIT/GU-3655-1 AUDIO UNIT.

23

DVD-5910/DVD-A1XV (2) SACD : SOURCE DIRECT ON MODECheck SACD Digital Audio Data(VSTEM data) and VSTEM communication. GU-3618(MAIN UNIT) [IC401]output and [IC405]input: [SD0-7],[SDCK],[XSAK],[SDEF],[XSHD2],[XSRQ]

(2) SACD : SOURCE DIRECT ON MODE

N.G.

Check Soldering. [IC401]:35-37,44-48,54,63,67-69pin [IC405]:164-176pin R414-426

SACD /VSTEM GU-3618(MAIN UNIT) [IC401] / [IC405] : [SD0-7],[SDCK],[XSAK],[SDEF],[XSHD2],[XSRQ]

N.G.

[IC401]:35-37,44-48,54,63,67-69pin [IC405]:164-176pin R414-426

O.K.DSD [1] GU-3618(MAIN UNIT) [IC405] :[DSARS],[DSALS],[DSASW],[DSAC],[DSAR],[DSAL], [BCKAO],[DSAMR],[DSADML],[EXCK01]

O.K.Check DSD Data. [1] GU-3618(MAIN UNIT) [IC405]output:[DSARS],[DSALS],[DSASW],[DSAC], [DSAR],[DSAL],[BCKAO],[DSAMR],[DSADML],[EXCK01]

N.G.

Check Soldering. [IC405]:76,74,71,69,66,64,60,56,55pin R464-R473

N.G.

[IC405]:76,74,71,69,66,64,60,56,55pin R464-R473

O.K.DSD [2] GU-3618(MAIN UNIT)

O.K.Check DSD Data. [2] GU-3618(MAIN UNIT) Audio selector input/output: [DSDFL],[DSDFR],[DSDSW],[DSDC],[DSDSL],[DSDSR],[DSDBCK] [IC119,IC120]:1pin(SEL_1394)"L"?

N.G.

Check the circumference soldering of [IC119]and [IC120]

[DSDFL],[DSDFR],[DSDSW],[DSDC],[DSDSL],[DSDSR],[DSDBCK] [IC119,IC120]:1pin(SEL_1394)"L"?

N.G.

[IC119] [IC120]

O.K.DSD [3] GU-3618(MAIN UNIT)

O.K.Check DSD Data.[3] GU-3618(MAIN UNIT) Audio selector input/output: [DSDFL],[DSDFR],[DSDSW],[DSDC],[DSDSL],[DSDSR],[DSDBCK] [IC124,IC125]:1pin(DSD_SEL)"H"?

N.G.

Check the circumference soldering of [IC124]and [IC125]

[DSDFL],[DSDFR],[DSDSW],[DSDC],[DSDSL],[DSDSR],[DSDBCK] [IC124,IC125]:1pin(DSD_SEL)"H"?

N.G.

[IC124] [IC125]

O.K.GU-3653-1 SYSTEM UNIT/GU-3655-1 AUDIO UNIT

O.K.Continue to the check process of GU-3653-1 SYSTEM UNIT/GU-3655-1 AUDIO UNIT.

(3) SACD : SOURCE DIRECT OFF MODECheck SACD Digital Audio Data(VSTEM data) and VSTEM communication. GU-3618(MAIN UNIT) [IC401]output and [IC405]input: [SD0-7],[SDCK],[XSAK],[SDEF],[XSHD2],[XSRQ]

(3) SACD : SOURCE DIRECT ON MODE

N.G.

Check Soldering. [IC401]:35-37,44-48,54,63,67-69pin [IC405]:164-176pin R414-426

SACD /VSTEM GU-3618(MAIN UNIT) [IC401] / [IC405] : [SD0-7],[SDCK],[XSAK],[SDEF],[XSHD2],[XSRQ]

N.G.

[IC401]:35-37,44-48,54,63,67-69pin [IC405]:164-176pin R414-426

O.K.Check DSD Data. [1] GU-3618(MAIN UNIT) [IC405]output/[IC801]input: [DSARS.],[DSALS.],[DSASW.],[DSAC.],[DSAR.],[DSAL.], [BCAO.],[EXCK01.]

O.K.Check Soldering. [IC405]:76,74,71,69,66,64,60,56,55,13pin R486-R493 [IC801]:27,38-44pin

DSD [1] GU-3618(MAIN UNIT) [IC405]output/[IC801]input: [DSARS.],[DSALS.],[DSASW.],[DSAC.],[DSAR.],[DSAL.],[BCKAO.],[EXCK01.]

N.G.

[IC405]:76,74,71,69,66,64,60,56,55,13pin R486-R493 [IC801]:27,38-44pin

N.G.

O.K.DSD [2] GU-3618(MAIN UNIT)

O.K.Check DSD Data. [2] GU-3618(MAIN UNIT) [IC801]output: [TSD0-2.],[TWS.],[TBCK.],[PMCK.] [IC801]:4pin(SELEXT)"L"?

N.G.

Check Soldering. [IC801]:17,19-23pin R806-R811 [IC801]:4pin,[IC115]:12pin

[IC801]output: [TSD0-2.],[TWS.],[TBCK.],[PMCK.] [IC801]:4pin(SELEXT)"L"?

N.G.

[IC801]:17,19-23pin R806-R811 [IC801]:4pin,[IC115]:12pin

O.K.DSD [3] GU-3618(MAIN UNIT)

O.K.Check DSD Data.[3] GU-3618(MAIN UNIT) Audio selector input/output: [PDATA0-2],[PBCK],[PLRCK],[PMCK] [IC124,IC125]:1pin(DSD_SEL)"L"?

N.G.

Check the circumference soldering of [IC124]and [IC125]

[PDATA0-2],[PBCK],[PLRCK],[PMCK] [IC124,IC125]:1pin(DSD_SEL)"L"?

N.G.

[IC124] [IC125]

O.K.GU-3653-1 SYSTEM UNIT/GU-3655-1 AUDIO UNIT

O.K.Continue to the check process of GU-3653-1 SYSTEM UNIT/GU-3655-1 AUDIO UNIT.

24

DVD-5910/DVD-A1XV

2. GU-3653-1 (SYSTEM UNIT)/GU-3655 (AUDIO UNIT)(1) CD,DVD-VIDEO/AUDIO,(SACD-SOURCE DIRECT OFF) Check connection Mecha UNIT GU-3653-1(SYSTEM UNIT) [CX301]output signal

2. GU-3653-1 (SYSTEM UNIT)/GU-3655 (AUDIO UNIT)(1) CD,DVD-VIDEO/AUDIO,(SACD-SOURCE DIRECT OFF)

N.G.

Check Soldering, FFC cable [CX301] [CY301]:GU-3618 FFC cable, insert condition

GU-3653-1(SYSTEM UNIT) [CX301]

FFC

N.G.

[CX301] [CY302]:GU-3618 FFC

O.K. Check input signal : IC105 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) 75(256fs),79(512fs),90(BCK),92(LRCK),93(TSD0: FFL/FR), 94(TSD1 : FSL/SR),96(TSD2 : FC/SW), 97(TSD3 : MIXL/MIXR : without SACD)pin check

O.K.IC105 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) 75(256fs), 79(512fs), 90(BCK), 92(LRCK), 93(TSD0FL/FR), 94(TSD1SL/SR), 96(TSD2C/SW), 97(TSD3MIXL/MIXRwithout SACD)pin check

N.G.

Check Soldering. FB101~107,IC107

N.G.

FB101 107, IC107

O.K. Check output signal : IC105 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) 21(BCK),22(LRCK),10(FL/FR),12(C/SW), 13(SL/SR),14(MIXL/MIXR : without SACD)

O.K.Check Soldering.

N.G.

84pin : 1394-H 85pin : Fs=192/176.4-H other Fs-L 87pin : L 88pin : D.L.-H

IC105 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) 21(BCK), 22(LRCK), 10(FL/FR),12(C/SW), 13(SL/SR),14(MIXL/MIXRwithout SACD)

N.G.

84pin1394- 85pinFs=192/176.4-Hother Fs- 87pin 88pinD.L.-

O.K. Check Soldering. GU-3653-1(SYSTEM UNIT)

O.K.DSP DSP "0000" N.G. page 17

Check DSP operation Check Firm version on DSP 0000 indicate is N.G. (refer page 17.)

N.G.

[IC305]:(DSP RESET)121pin "H" Level OK? "H" "L" : N.G. [IC305] to [IC306] Signal [IC105] to [IC305] Signal [IC306]:(FLASH ROM for DSP)

GU-3613-1(SYSTEM UNIT)

N.G.

[IC305]:(DSP RESET)121pin "H" Level OK? "H" "L"N.G. [IC305],[IC306] [IC105],[IC305] [IC306]:(FLASH ROM for DSP)

O.K. Check DATA Signal -1 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) [IC305](DSP) : input

O.K.

N.G.

Check Soldering. R158,159,169,170,164,165

-1 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) [IC305](DSP)input

N.G.

158,159,169,170,164,165

O.K. Check DATA Signal -2 GU-3653-1(SYSTEM UNIT) [IC305](DSP) : output 86(FL/FR),82(C/SW),81(SL/SR),80(MIXL/MIXR)pin Each output pin Level "H": NG

O.K.

N.G.

-2 GU-3653-1(SYSTEM UNIT) [IC305](DSP)output 86(FL/FR),82(C/SW,81(SL/SR),80(MIXL/MIXRpin "H"

N.G.

O.K. Check DATA Signal -3 GU-3653-1(SYSTEM UNIT) [IC305](DSP) : output [IC105](EPM3128ATC100) : input

O.K.

N.G.

Check Soldering. R366,372,373,374

-3 GU-3653-1(SYSTEM UNIT) [IC305](DSP)output [IC105](EPM3128ATC100)input

N.G.

366,372,373,374

O.K.

O.K.

25

DVD-5910/DVD-A1XV Check DATA Signal -4 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) : output to Advanced AL24(MIXL/R) 50~55pin [IC502](EP1C12Q240C6) : input 11,28,200,203,206pin [IC502](EP1C12Q240C6) : output to DAC(MIXL/R) 95,99,101,104pin [IC105](EPM3128ATC100) : output to DAC(FL/FR/C/SW) 44~49,54,55pin

-4 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100)output to Advanced AL24(MIXL/R) 50 55pin [IC502](EP1C12Q240C6)input 11,28,200,203,206pin [IC502](EP1C12Q240C6)output to DAC(MIXL/R) 95,99,101,104pin [IC105](EPM3128ATC100)output to DAC(FL/FR/C/SW) 44 49,54,55pin

Check Soldering. CX332,CY332(Connection to 5.1ch AUDIO UNIT) (GU-3653-1 to GU-3655-2) CX192,CY192(Connection to MIXch AUDIO UNIT) (GU-3655-1 to GU-3655-2) CX173,CX191(Connection to 1394 PWB) (GU-3653-1 to GU-3517)

N.G.

N.G.

GU-3655-1(AUDIO UNIT) [IC401,501](DAC for MIXL / MIXR) : input 4~7pin(WCK,DATA-MIXL / -MIXR,BCK,MCK) ----IC401,501:mono DAC MODE GU-3655-2(AUDIO UNIT) [IC701](DAC for FL/FR) [IC801](DAC for S/SW),[IC901](DAC for SL/SR) : input 4~7pin(LRCK=1fs,DATA,BCK=64fs,MCK=256fs) ----IC701,801,901:stereo DAC MODE O.K. Check DAC output GU-3655(AUDIO UNIT) [IC401][IC501][IC701][IC801][IC901]:output

GU-3655-1(AUDIO UNIT) [IC401,501](DAC for MIXL / MIXR) : input 4 7pin(WCK,DATA-MIXL / -MIXR,BCK,MCK ----IC401,501:mono DAC MODE

CX332,CY332(Connection to 5.1ch AUDIO UNIT) (GU-3653-1 to GU-3655-2) CX192,CY192(Connection to MIXch AUDIO UNIT) (GU-3655-1 to GU-3655-2) CX173,CX191(Connection to 1394 PWB (GU-3653-1 to GU-3517)

GU-3655-2(AUDIO UNIT) [IC701](DAC for FL/FR) [IC801](DAC for S/SW),[IC901](DAC for SL/SR) : input 4 7pin(LRCK=1fs,DATA,BCK=64fs,MCK=256fs ----IC701,801,901:stereo DAC MODE

O.K.

N.G.

Check Soldering. / Check Supply Voltages. [IC401][IC501][IC701][IC801][IC901] 10~14pin(control line)

DAC GU-3655AUDIO UNIT) [IC401][IC501][IC701][IC801][IC901]:output

N.G.

/ [IC401][IC501][IC701][IC801][IC901] 10 14pincontrol line)

O.K.OP AMP GU-3655AUDIO UNIT) [IC403] [IC406],[IC503 IC506],[IC702 IC705], [IC802 IC805],[IC902 IC905]:output:7pin

O.K. Check OP AMP output GU-3655(AUDIO UNIT) [IC403]~[IC406],[IC503~IC506],[IC702~IC705], [IC802~IC805],[IC902~IC905]:output:7pin

N.G.

Check Soldering. Check Power Supply Voltages. [IC403]~[IC406],[IC503~IC506], [IC702~IC705],[IC802~IC805], [IC902~IC905]:output:7pin

N.G.

[IC403] [IC406],[IC503 IC506], [IC702 IC705],[IC802 IC805], [IC902 IC905]:output:7pin

O.K. GU-3655AUDIO UNIT) ch OUTPUT MUTE circuitMUTE TR(TR402TR403, TR502,TR503,TR703 708, TR803 808,TR903 908) TR-BASE terminalabout -9V (at MUTE off) Check Soldering. Output Jack

O.K. Check Soldering. Check AUDIO OUT GU-3655(AUDIO UNIT) Check OUTPUT terminal (Each channels) MUTE circuit : MUTE TR(TR402~TR403,TR502,TR503, TR703~708,TR803~808,TR903~908) TR-BASE terminal : about -9V (at MUTE off) Check Soldering. Output Jack

N.G.

N.G.

O.K.

O.K.

END

26

DVD-5910/DVD-A1XV (2) SACD-SOURCE DIRECT ONCheck connection Mecha UNIT GU-3653-1(SYSTEM UNIT) [CX301]output signal

(2) SACD-SOURCE DIRECT ON

N.G.

Check Soldering, FFC cable [CX301] [CY302]:GU-3618 FFC cable, insert condition

GU-3653-1(SYSTEM UNIT) [CX301]

N.G.

O.K.Check input signal : IC105 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) 75(256fs),79(512fs),90(BCK),92(LRCK),93(TSD0 : FL/FR), 94(TSD1 : SL/SR),96(TSD2 : C/SW)

FFC [CX301] [CY302]:GU-3618 FFC

O.K.

N.G.

Check Soldering. FB101~107, IC107

O.K.Check output signal : IC105 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) 21(BCK),22(LRCK),10(FL/FR),12(C/SW), 13(SL/SR),14(MIXL/MIXR : without SACD)

IC105 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) 75(256fs), 79(512fs), 90(BCK), 92(LRCK), 93(TSD0FL/FR), 94(TSD1SL/SR),96(TSD2C/SW

N.G.

FB101 107IC107

O.K.

N.G.

Check Soldering. FB101~107, IC107

O.K.Check DSP operation Refer(1) CD,DVD-VIDEO/AUDIO,(SACD-SOURCE DIRECT OFF)

IC105 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) 21(BCK), 22(LRCK), 10(FL/FR), 12(C/SW), 13(SL/SR), 14(MIXL/MIXRwithout SACD)

N.G.

FB101 107IC107

O.K.

N.G.O.K.

DSP (1) CD,DVD-VIDEO/AUDIO,(SACD-SOURCE DIRECT OFF)

O.K.

Check DATA Signal -1 GU-3653-1(SYSTEM UNIT) [IC305](DSP) : output 86(FL),82(C),81(SL),57(FR),62(SW),70(SR) [IC105](EPM3128ATC100) : input

N.G.

-1

Check Soldering. R366,372,373,385,384,402

GU-3653-1(SYSTEM UNIT) [IC305](DSP)output 86(FL),82(C,81(SL),57(FR),62(SW),70(SR) [IC105](EPM3128ATC100)input

N.G.

R366,372,373,385,384,402

O.K.Check DATA Signal -2 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100) : output to Advanced AL24(MIXL/R) 50~55pin [IC502](EP1C12Q240C6) : input 11,28,200,203,206pin [IC502](EP1C12Q240C6) : output to DAC(MIXL/R) 95,99,101,104pin [IC105](EPM3128ATC100) : output to DAC(FL/FR/C/SW) 44~49,54,55pin

O.K. -2 GU-3653-1(SYSTEM UNIT) [IC105](EPM3128ATC100)output to Advanced AL24(MIXL/R) 50 55pin [IC502](EP1C12Q240C6)input 11,28,200,203,206pin [IC502](EP1C12Q240C6)output to DAC(MIXL/R) 95,99,101,104pin [IC105](EPM3128ATC100)output to DAC(FL/FR/C/SW) 44 49,54,55pin GU-3655-1(AUDIO UNIT) [IC401,501](DAC for MIXL / MIXR) : input 4 7pin(GND,DATA-MIXL or -MIXR,GND,BCK=64fs ----IC401,501:mono DAC MODE GU-3655-2(AUDIO UNIT) [IC701](DAC for FL/FR) [IC801](DAC for S/SW),[IC901](DAC for SL/SR) : input 4 7pin(DATA-1,DATA-2,BCK="L",MCK=64fs ----IC701,801,901:stereo DAC MODE

Check Soldering. CX332,CY332(Connection to 5.1ch AUDIO UNIT) (GU-3653-1 to GU-3655-2) CX192,CY192(Connection to MIXch AUDIO UNIT) (GU-3655-1 to GU-3655-2) CX173,CX191(Connection to 1394 PWB) (GU-3653-1 to GU-3517)

N.G.

GU-3655-1(AUDIO UNIT) [IC401,501](DAC for MIXL / MIXR) : input 4~7pin(GND,DATA-MIXL or -MIXR,GND,BCK=64fs) ----IC401,501:mono DAC MODE

N.G.

GU-3655-2(AUDIO UNIT) [IC701](DAC for FL/FR) [IC801](DAC for S/SW),[IC901](DAC for SL/SR) : input 4~7pin(DATA-1,DATA-2,BCK="L",MCK=64fs) ----IC701,801,901:stereo DAC MODE

CX332,CY332(Connection to 5.1ch AUDIO UNIT) (GU-3653-1 to GU-3655-2) CX192,CY192Connection to MIXch AUDIO UNIT (GU-3655-1 to GU-3655-2) CX173,CX191Connection to 1394 PWB) (GU-3653-1 to GU-3517)

O.K.Check DAC output ~ Refer(1) CD,DVD-VIDEO/AUDIO,(SACD-SOURCE DIRECT OFF)

O.K.DAC (1) CD,DVD-VIDEO/AUDIO,(SACD-SOURCE DIRECT OFF)

O.K.

O.K.

END

27

DVD-5910/DVD-A1XV

3. GU-3654-1 (VIDEO UNIT)(1) Interlace output [Y,Cb,Cr] does not outputed.. Check Power Supply Voltages. GU-3654-1(VIDEO UNIT) Digital Power Supply Voltages. +5V_D1,+3.3V_D1, +2.5V_D1 Analog Power Supply Voltages. +5V_V1,-5V_V1

3. GU-3654-1 (VIDEO UNIT)(1) [Y,Cb,Cr] GU-3654-1(VIDEO UNIT) +5V_D1,+3.3V_D1, +2.5V_D1 +5V_V1,-5V_V1

N.G.

Check Soldering. [CY081],[IC108] Circumference of [IC108](BA25BCOFP-E2) [CY031]

N.G.

[CY081],[IC108] [IC108](BA25BCOFP-E2) [CY031]

O.K. Check Digital signal for Video[1]. GU-3654-1(VIDEO UNIT) Video Encoder [IC201](ADV7314)input: [YUV0~7],[I_VSYNC],[I_HSYNC],[SEL_CLK]

O.K.Check Soldering.

N.G.

[CY331]:23-30,10,11,21pin Circumference of [IC101],[IC102] (SN74LVC245APW) Circumference of [IC106](SN74LVC157APW) Circumference of [IC201]

[1] GU-3654-1(VIDEO UNIT) [IC201](ADV7314) : [YUV0 7],[I_VSYNC],[I_HSYNC],[SEL_CLK]

N.G.

[CY331]:23-30,10,11,21pin [IC101],[IC102] (SN74LVC245APW) [IC106](SN74LVC157APW) [IC201]

O.K. Check control signal for Video Encoder [IC201]. GU-3654-1(VIDEO UNIT) [SDA1],[SCK1],[RST_V]

N.G.

Check Soldering. [CY331]:14,15,9pin Circumference of [IC201]

O.K.[IC201] GU-3654-1(VIDEO UNIT) [SDA1],[SCK1],[RST_V]

N.G.

[CY331]:14,15,9pin [IC201]

O.K. Check Video Encoder circuit. GU-3654-1(VIDEO UNIT) [IC201]:

N.G.

Check the soldering [IC201] and circumference soldering of [IC201].

O.K. GU-3654-1(VIDEO UNIT) [IC201]:

N.G.

[IC201]

O.K. Check Video Buffer circuit. GU-3654-1(VIDEO UNIT) Yi:[VR101],[TR201] Cb:[VR102],[TR202] Cr:[VR103],[TR203]

N.G.

Check the soldering [VR101~103],[TR201~203] and circumference soldering of [VR101~103], [TR201~203].

O.K. GU-3654-1(VIDEO UNIT) Yi:[VR101],[TR201] Cb:[VR102],[TR202] Cr:[VR103],[TR203]

N.G.

[VR101 103],[TR201 203]

O.K. Check Video Filter and Amp. circuit. GU-3654-1(VIDEO UNIT) Yi:[LF101],[TR204],[IC202] Cb:[LF102],[TR205],[IC203] Cr:[LF102],[TR206],[IC204]

N.G.

Check the soldering [LF101~102],[TR204~206],[IC202~204] and circumference soldering of [LF101~102],[TR204~TR206],[IC202~204].

O.K. GU-3654-1(VIDEO UNIT) Yi:[LF101],[TR204],[IC202] Cb:[LF102],[TR205],[IC203] Cr:[LF102],[TR206],[IC204]

N.G.

O.K. Check Clamp circuit. GU-3654-1(VIDEO UNIT) [IC104](TC74HC123AF),[IC105](TC4W53F) [TR103].[TR104] [TR207~209]

[LF101 102],[TR204 206],[IC202 IC204]

N.G.

Check the soldering [IC104],[IC105],[TR103],[TR104],[TR207~209] and circumference soldering of [IC104],[IC105],[TR103],[TR104],[TR207~209]

O.K. GU-3654-1(VIDEO UNIT) [IC104](TC74HC123AF),[IC105](TC4W53F) [TR103].[TR104] [TR207 209]

N.G.

O.K. Check Video Output. GU-3654-1(VIDEO UNIT) Output Terminal:[JK101],[JK105~107].

[IC104],[IC105],[TR103],[TR104],[TR207209]

N.G.

Check the soldering [JK101],[JK105~107] and circumference soldering of [JIK101],[JK105`JK107].

O.K. GU-3654-1(VIDEO UNIT) :[JK101],[JK105 107].

O.K.

N.G.

END

[JK101],[JK105 107]

O.K.

28

DVD-5910/DVD-A1XV (2) Interlace output [V-OUT,S-OUT] does not outputed. Check Digital signal for Video[1]. GU-3654-1(VIDEO UNIT) Video Encoder [IC401](ADV7314)input: [YUV0~7],[I_VSYNC],[I_HSYNC],[SEL_CLK]

(2) [V-OUT,S-OUT] [1] GU-3654-1(VIDEO UNIT) [IC401](ADV7314) : [YUV0 7],[I_VSYNC],[I_HSYNC],[SEL_CLK]

N.G.

Check Soldering. Circumference of [IC401]

N.G.

[IC401]

O.K.Check control signal for Video Encoder [IC401]. GU-3654-1(VIDEO UNIT) [SDA1],[SCK1],[RST_V]

O.K.

N.G.

Check Soldering. Circumference of [IC401]

[IC401] GU-3654-1(VIDEO UNIT) [SDA1],[SCK1],[RST_V]

N.G.

[IC401]

O.K.Check Video Encoder circuit. GU-3654-1(VIDEO UNIT) [IC401]:

O.K.

N.G.

Check the soldering [IC401] and circumference soldering of [IC401].

GU-3654-1(VIDEO UNIT) [IC401]:

N.G.

[IC401]

O.K.Check Video Buffer circuit. GU-3654-1(VIDEO UNIT) Y:[VR401],[TR401] C:[VR402],[TR402]

O.K.

N.G.

Check the soldering [VR401],[VR402],[TR401],[TR402] and circumference soldering of [VR401],[VR402],[TR401],[TR402].

GU-3654-1(VIDEO UNIT) Y:[VR401],[TR401] C:[VR402],[TR402]

N.G.

[VR401],[VR402],[TR401],[TR402]

O.K.Check Video Filter and Amp. circuit. GU-3654-1(VIDEO UNIT) Y:[LF103],[TR403],[IC402],[IC404] C:[LF104],[TR404],[IC405] V:[IC402],[IC403]

O.K.Check the soldering [LF103~104],[TR403~404],[IC402~405] and circumference soldering of [LF103~104],[TR403~TR404],[IC402~405]. GU-3654-1(VIDEO UNIT) Y:[LF103],[TR403],[IC402],[IC404] C:[LF104],[TR404],[IC405] V:[IC402],[IC403]

N.G.

N.G.

[LF103 104],[TR403 404],[IC402 405]

O.K.Check Clamp circuit. GU-3654-1(VIDEO UNIT) [TR405],[TR406]

O.K.

N.G.

Check the soldering ,[TR405],[TR406], and circumference soldering of [TR405],[TR406].

GU-3654-1(VIDEO UNIT) [TR405],[TR406]

N.G.

[TR405],[IC406]

O.K.Check Video Output. GU-3654-1(VIDEO UNIT) Output Terminal:[JK103],[JK104].

O.K.

N.G.

Check the soldering [JK103],[JK104] and circumference soldering of [JIK103],[JK104].

GU-3654-1(VIDEO UNIT) Output Terminal:[JK103],[JK104].

N.G.

[JK103],[JK104]

O.K. END

O.K.

29

DVD-5910/DVD-A1XV

4. GU-3654-1 (VIDEO UNIT)/GU-3657(IP UNIT)(1) Progressive output [Y,Pb,Pr] does not outputed. Check Power Supply Voltages[2]. GU-3657(IP UNIT) +3.3V_D2,+2.5V_D3, +1.5V_D1, VTT(+1.25V) MAVREFR1~2,MBVREFR1~2 (+1.25V) VPLL_AVDD,SPLL_AVDD,MPLL_AVDD,SIMD_AVDD

4. GU-3654-1 (VIDEO UNIT)/GU-3657(IP UNIT)(1) [Y,Pb,Pr]

Check Soldering. N.G. [CY059],[CY301] Circumference of [IC803](LP2995M) R146~R151,C130,C131,C180,C181 FB101~FB104,C168~C175

[2] GU-3657(IP UNIT) +3.3V_D2,+2.5V_D3, +1.5V_D1, VTT(+1.25V) MAVREFR1 2,MBVREFR1 2 (+1.25V) VPLL_AVDD,SPLL_AVDD,MPLL_AVDD,SIMD_AVDD

N.G.

[CY059],[CY301] [IC803](LP2995M) R146 R151,C130,C131,C180,C181 FB101 FB104,C168 C175

O.K. Check oscillation waveform. GU-3657(IP UNIT) [IC101](sxT2-100):[REFCLKA],[REFCLKB] Check point:[R152],[R153]:66.666MHz OK? [IC101](sxT2-100):[PCICLK] Check point:[R142]:33.333MHz OK? [IC701~704](EM6A9320BI-4M):[ACK] Check point:[R767]:250MHz OK?

O.K.Check Soldering. N.G. Circumference of [X101](66.666MXTAL) Circumference of [IC101] Circumference of [IC701~704]

GU-3657(IP UNIT) [IC101](sxT2-100):[REFCLKA],[REFCLKB] Check point:[R152],[R153]:66.666MHz OK? [IC101](sxT2-100):[PCICLK] Check point:[R142]:33.333MHz OK? [IC701 704](EM6A9320BI-4M):[ACK] Check point:[R767]:250MHz OK?

[X101](66.666MXTAL)

N.G. [IC101] [IC701 704]

O.K. Check control signal for I/P Convertor [IC101]. GU-3657(IP UNIT) [RESETN],[IICO_DAT],[IICO_CLK]

O.K.N.G. Check Soldering. [CY301] Circumference of [IC103](TC7W241FU)

I/P [IC101] GU-3657(IP UNIT) [RESETN],[IICO_DAT],[IICO_CLK]

N.G.

[CY301] [IC103](TC7W241FU)

O.K. Check Digital signal for Video[2]. GU-3654-1(VIDEO UNIT) [IC107],[IC101](SN74LVC243APW)output: [YUV0P~7P],[I_VSYNC_P],[I_HSYNC_P],[I_CLK_P]

O.K.N.G. Check Soldering. Circumference of [IC101],[IC107] (SN74LVC245APW) [CX403]

[2] GU-3654-1(VIDEO UNIT) [IC107],[IC101](SN74LVC243APW)output: [YUV0P 7P],[I_VSYNC_P],[I_HSYNC_P],[I_CLK_P]

N.G.

[IC101],[IC107] [CX403]

O.K. Check Digital signal for Video[3]. GU-3657(IP UNIT) I/P Convertor [IC101](sxT2-100)input: [YUV0~7],[I_VSYNC],[I_HSYNC],[I_CLK]

O.K.N.G. Check Soldering. [CY403] [RA101],[RA102],[R101~104],[R109~112]

[3] GU-3657(IP UNIT) I/P Convertor [IC101](sxT2-100)input: [YUV0 7],[I_VSYNC],[I_HSYNC],[I_CLK]

N.G.

[CY403] [RA101],[RA102],[R101 104],[R109 112]

O.K. Check Digital output for Progressive Video[1]. GU-3657(IP UNIT) [IC101]output: [YP0~9],[CP0~9],[P_VSYNC],[P_HSYNC], [P_DE],[VOACLK]

O.K.N.G. Check Soldering. Circumference of [IC101] [RA105~8],[R113~120] [CY403]

[1] GU-3657(IP UNIT) [IC101]output: [YP0 9],[CP0 9],[P_VSYNC],[P_HSYNC],[P_DE],[VOACLK]

N.G.

[IC101] [RA105 8],[R113 120] [CY403]

O.K. Check Digital output for Progressive Video[2]. GU-3654-1(VIDEO UNIT) Video Encoder [IC201](ADV7314)input: [Y0~9],[C0~9],[P_VSYNC],[P_HSYNC], [C_REF],[SEL_CLK]

O.K.Check Soldering. [CX403] Circumference of [IC106](SN74LVC157APW) Circumference of [IC201]

[2] GU-3654-1(VIDEO UNIT) Video Encoder [IC201](ADV7314)input: [Y0 9],[C0 9],[P_VSYNC],[P_HSYNC],[C_REF],[SEL_CLK]

N.G.

N.G.

[CX403] [IC106](SN74LVC157APW) [IC201]

O.K. GU-3654-1(VIDEO UNIT) [IC103],[TR101],[TR102].

O.K. Check Clamp circuit. GU-3654-1(VIDEO UNIT) [IC103],[TR101],[TR102].

N.G.

N.G.

Check the soldering [IC103],[TR101],[TR102] and circumference soldering [IC103],[TR101],[TR102]

[IC103],[TR101],[TR102]

O.K.

O.K.

END

30

DVD-5910/DVD-A1XV

5. GU-3656-2 (DIGITAL POWER UNIT).

5. GU-3656-2 (DIGITAL POWER UNIT)N.G.(Open)

Check FUSE ConditionFUSE (F901) OPEN?

Check Primary Parts and Soldering. [D901~D904],[IC901],[C909]

FUSE (F901)

N.G. O.K.

[D901 D904],[IC901],[C909]

O.K. Check +3.3V_NSW Output Voltage Check 3.3V DC (non-swiched) Voltage is O.K.? (CX121 6pin Output)

N.G.

Check Soldering. [IC902]: ALL pin (TA76432FC) [IC909]: ALL pin (PC123-Y) [D907]: (FMJ-2303)

+3.3V NSW (CX121 6pin )

N.G.

[IC902]: (TA76432FC) [IC909]: (PC123-Y) [D907]: (FMJ-2303)

O.K. Check +3.3V Output Voltage Check 3.3V DC (swiched) Voltage is O.K.? (CW101 9pin Output)

O.K.N.G. Check Parts and Soldering. [TR908]: (HAT2053)

+3.3V (CW101 9pin )

N.G. O.K.

[TR908]: (HAT2053)

O.K. Check +12V_M1 Output Voltage Check 10V~12V DC is O.K.? (about) (CW101 2pin Output)

+12V M1

N.G.

Check Parts and Soldering. [TR911]: (2SB1268) and Ather Cirquits

(CW101 2pin ) 10V 12V

N.G.

[TR911]: (2SB1268)

O.K.-32V M1 (CX035 1PIN )

O.K. Check -32V_M1 Output Voltage Check -32V DC is O.K.? (about) (CX035 1pin Output)

N.G.

[R976]: (2.2)

N.G.

Check Parts Condition [R976]: (2.2)

O.K. [TR913]: (2SB1185) [D906]: (MTZJ36B)

N.G.

O.K.

O.K. Check Parts and Soldering. [TR913]: (2SB1185) [D906]: (MTZJ36B)

N.G O.K. Repare These Parts (May be broken) [IC101]: (M66005) GU-3656-3 (DISPLAY UNIT) [R976]: (2.2)

[IC101]: (M66005) GU-3656-3(DISPLAY UINT) [R976]: (2.2)

+2.5V (CX063 1pin )

N.G.

[TR906]: (2SC5370) [IC907]: (TA76432FC)

Check +2.5V Output Voltage Check 2.5V DC is O.K.? (CX063 1pin Output)

N.G.

Check Parts and Soldering. [TR906]: (2SC5370) [IC907]: (TA76432FC)

O.K. +1.5V (CX059 3pin )

N.G.

O.K. Check +1.5V Output Voltage Check 1.5V DC is O.K.? (CX059 3pin Output)

[TR912]: (2SC5370) [IC910]: (TA76432FC)

N.G.

Check Parts and Soldering. [TR912]: (2SC5370) [IC910]: (TA76432FC)

O.K.-12V (CW101 2pin )

N.G. O.K.

[TR902]: (2SD1904)

O.K. Check -12V_M1 Output Voltage Check -11V ~ -14V DC is O.K.? (about) (CW101 2pin Output)

N.G.

Check Parts and Soldering. [TR902]: (2SD1904)

O.K.

END

31

AVR-5805/AVC-A1XV

ELECTRICAL ADJUSTMENT FOR VIDEO1. SETTING(1) Connect the monitor TV to the video output terminal. (2) Connect the oscilloscope to the Y-signal and C-signal of S-VIDEO output terminal and each terminate at 75 Ohms. (3) Connect the oscilloscope to the Y-signal, PB-signal and PR-signal of Component video output terminal and each terminate at 75 Ohms. Use the 75 Ohms resistance must be 1% (4) DVD test disc : DVDT-S01

1. (1) VIDEO OUT (2) S2 VIDEO OUT Y C 75 (3) COMPONENT VIDEO OUT Y/PB/PR 75 75 1 (4) DVD DVDT-S01

2. BEFORE ADJUSTMENT 2.1. Setting the Oscilloscope as below.(1) PB/PR (a) TIME/DIV : 20s (b) VOLT/DIV : 100mV (Use the probe : x10 ) (2) Y/C (a) TIME/DIV : 20s (b) VOLT/DIV : 50mV (Use the probe : x10 ) Power on. Power Supply USA & Canada : 120V Europe : 230V Japan : 100V

2. 2.1. (1) PB/PR (a) TIME/DIV : 20s (b) VOLT/DIV : 100mV x10 (2) Y/C (a) TIME/DIV : 20s (b) VOLT/DIV : 50mV x10 100V

2.2. Preparation(1) Power on. (2) Push [OPEN/CLOSE] button, then open the Disc Tray. (3) Set DVD test disc (DVDT-S01) on the Disc Tray, and then push [CLOSE] button. (4) FL display appear "STOP", push [PLAY] button to playback DVD. (5) Push the [DISPLAY] button of remote control unit and then appear the ON-Screen Display (GUI) on the monitor TV. (6) Push the [+10] and [2] button, select Title 12 of DVD. (7) Push the [ENTER] button, playback Title 12. (color bar 75%)

2.2. (1) AC ON (2) OPEN/CLOSE DVD DVDT-S01 CLOSE (3) "STOP" PLAY (4) DISPLAY GUI (5) +10 2Title12 (6) ENTERTitle12 75%

32

AVR-5805/AVC-A1XV 2.3. Procedure(1) Adjust the signal of S-VIDEO OUT by the wave of oscilloscope. (a) Target, Y-signal Point Adjustment Value Waveform : : VR104 1000 20mV

2.3. (1) S2 VIDEO OUT (a) Y VR104 1000 20mV

Y

Y

Y-signal of S-VIDEO OUT

S2 VIDEO OUT Y

(b) Target, C-signal Point Adjustment Value Waveform

: :

VR105 *286 5mV

(b) C

VR105 286 5V

C

C

C-signal of S-VIDEO OUT *300 5mV for Europe model (2) Adjust the signal of COMPONENT OUT by the wave of oscilloscope. (a) Target, Y-signal Point Adjustment Value Waveform : : VR101 1000 20mV

S2 VIDEO OUT C

(2) COMPONENT OUT (a) Y VR101 1000 20V

Y

Y

Y-signal

Y

(b) Target, PB-signal Point Adjustment Value Waveform

: :

VR102 *525 10mV

(b) PB

VR102 525 10V

PB

PB

PB-signal

PB

33

AVR-5805/AVC-A1XV(c) Target, PR-signal Point Adjustment Value Waveform (c) PR/CR

: :

VR103 *525 10mV

VR103 525 10V

PR

PR

PR-signal *486 10mV for U.S.A. & Canada model

PR

34

DVD-5910/DVD-A1XV

BLOCK DIAGRAM

35

DVD-5910/DVD-A1XV

SEMICONDUCTORS / Only major IC's are shown, general IC's etc. are omitted to list.

IC'sNote: Abbreviation ahead of IC No. indicates the name of P.W.B., etc. ) : IC No.

MA: Main P.W.B. SY: System P.W.B.

IE : IEEE1394 P.W.B. AP: Audio/Power P.W.B.

VI: VIDEO P.W.B. IP: IP P.W.B.

PO: POWER P.W.B.

CXD1885Q(MA:IC507)Top View

DRAM I/F

PWM.FGDA3 (SLED2_TILT)

D/A

DA2 (FSCON)

DVDD33

DA0 (TSCON)

DA1 (SLED)

GPWM5

GPWM4

GPWM3

GPWM2

GPWM1

GPWM0

SPWM2

SPWM1

DVDD18

DVDD18

RD10

RD11

RD12

RD13

RD14

RD15

DVSS

DVSS

RD9

RD0

RD1

RD2

RD3

RD4

RD5

RA1

RA2

RA3

RA4

RA5

RA6

RA7

RA8

RA9

156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 DVDD33 157 RD8 158 TEST0 159 TEST1 160 TEST2 161 TEST3 162 TEST4 163 TEST5 164 TEST6 165 TEST7 166Test/Monitor Pin

AVDD33

XUCAS

XLCAS

XMWR

XMOE

XRAS

RA10

RA11

AVSS

RD6

RD7

RA0

FG

104 AVDD18 103 VREFL 102 VREFH 101 AD9 100 AD8 99 AD7 98 AD6 97 AD5 96 AD4 95 AD3 94 AVDD33 93 AD2 92 AD1 91 AD0 90 AVSS 89 AVSS 88 RC 87 LPF2 86 LPF1 85 VCOI 83 VFBC 82 CHG 81 JMOUT 80 JMREF 79 AVDD33 78 IREF 77 TLC1 76 TLC0 75 HF 74 ATC 73 AVSS 72 DTC 70 HFD 69 RFOKGH 68 SCLKH 67 SO 66 SI 65 CSL 64 EXPLDT 63 EXVCO 61 LRCK 60 DOTK 59 DADT 58 C2PO 57 DRVRDY 56 DRVCLK 55 DRVRX 53 DVDD33 1DVDD33 VSTEM I/F Audio D/A ASP S-I/O, Defect etc Data PLL/Data Slicer A/D

TEST8 167 TEST9 168 TEST10 169 TEST11 170 TEST12 171 TEST13 172 TEST14 173 TEST15 174 MODSEL0 175 MODSEL1 176 DVSS 177 MODSEL2 178 GIO0 179 GIO1 180 GIO2 181 GIO3 182 DVDD33 183 GIO4 184 GIO5 185 GIO6 186 GIO7 187 DVDD18 188 GIO8 189 GIO9 190 GIO10 191 GIO11 192 GIO12 193 DVSS 194 GIO13 195 GIO14 196 GIO15 197 GIO16 198 GIO17 199 GIO18 200 GIO19 201 TRST 202 TMS 203

84 AVDD18

General Port

71 MIRRORH

62 BCK

JTAG

TDI 204 TCK 205 TDO 206 VMCHG 207 DVDD18 208 2ALCR

54 DRVTX

3MSEL0

4MSEL1

5MA0

6MA1

7MA2

8MA3

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52DVSS DVSS DVSS MCS DVDD33 MRDY SYSCK DVDD18 XHAC MINT TESTSEL DRVRST DRVIRQ DVDD18 MRD MALE MD6 MD0 MD1 MD2 MD3 MD4 MD5 MD7 XO HDRQ VEFG MWR VDT7 VDT6 VDT5 VDT4 VDT3 VDT2 VDT1 VDT0 XSHD DCK MA4 MA5 MA6 MA7 MA8 XI

B/E MCU I/F

Clock

VSTEM I/F

36

DVD-5910/DVD-A1XV

Block Diagram

16/4M DRAM

HFD

BCA Memory manager

ECC Core EDC MPEG I/F Video

HF

Data Slicer Data-PLL ASP Serial I/F

DVD Demodulation CD-DSP (DDCD) VSTEM Serial I/F Spindle

ASP PWM ATC JTAG Mecha control Servo singnal

Serial Command CD-ROM Header Dec. Audio I/F DSP CLK/Mode Audio MCU I/F ICU D/A PWM Peri. CLK Servo control X'tal MCU

VSTEM

TZC

TC DSP CMD/ RSP reg.

GIO

Direction ROM/RAM ICU

Data RAM Timer

A/D

FunctionsNo. 1 3 4 5 6 7 8 9 10 11 12 Terminal Name DVDD33 MSEL0 MSEL1 MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 I/O P I I I I/O I/O I/O I/O I/O I/O I/O I/O I I I/O I/O I/O I/O I/O I/O P I/O I/O I I I P I O O D D D D D D D D D D D D D D D D D D D D D D D D D D D A/D

(A/D : Analog/Digital, PU : Pull-up, PD : Pull-down, SMT=Schumitt )Classification VDD & GND MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F VDD & GND MCU I/F MCU I/F MCU I/F MCU I/F MCU I/F VDD & GND MCU I/F MCU I/F MCU I/F Digital 3.3V Power for I/O. Chip select input. (L: Reset) MCU I/F mode select 0. MCU I/F mode select 1. MCU Adress input 0 / data I/O 0 . MCU Adress input 1 / data I/O 1. MCU Adress input 2 / data I/O 2. MCU Adress input 3 / data I/O 3. MCU Adress input 4 / data I/O 4. MCU Adress input 5 / data I/O 5. MCU Adress input 6 / data I/O 6. MCU Adress input 7 / data I/O 7. MCU Adress input 8 . TEST Select input. MCU data I/O 0 . MCU data I/O 1. MCU data I/O 2. MCU data I/O 3. MCU data I/O 4. MCU data I/O 5. Digital Ground. MCU data I/O 6. MCU data I/O 7 . MCU Adress latch signal input. MCU Chip Select signal input. MCU Write strobe signal. digital 3.3V Power. (for I/O ) MCU Read Strobe signal. MCU Ready signal. (L: Wait) MCU Interrupt signal. (L: Interrupt request) * * * * * * * * * * * * * * * * * * * * * * * * * * Function PU PD SMT

2 ALCR

13 MA8 14 TESTSEL 15 16 17 18 19 20 22 23 24 25 26 28 29 30 MD0 MD1 MD2 MD3 MD4 MD5 MD6 MD7 MALE MCS MWR MRD MRDY MINT

21 DVSS

27 DVDD33

37

DVD-5910/DVD-A1XV

No. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91

Terminal Name SYSCK DVDD18 XI XO DVSS VDT7 VTD6 DVSS VDT5 VDT4 VDT3 VDT2 VDT1 VDT0 HDRQ XHAC VEFG XSHD DCK DRVIRQ DRVRST DVDD18 DVDD33 DRVTX DRVRX DRVCLK DRVRDY C2PO DADT DOTX LRCK BCK EXVCO EXPLDT CSL SI SO SCLKH RFOKGH HFD MIRRORH DTC AVSS ATC HF TLC0 TLC1 IREF AVDD33 JMREF JMOUT CHG VFBC AVDD18 VCOI LPF1 LPF2 RC AVSS AVSS AD0

I/O O P I O P O O P O O O O O O I O O O O O I P P O I I O O O O O O I I O I O O I I I I P I I O O I P I O I I P I O O I P P I

A/D D D D D D D D D D D D D D D D D D D

Classification Clock VDD & GND Clock Clock VDD & GND VSTEM A/V VSTEM A/V VDD & GND VSTEM A/V VSTEM A/V VSTEM A/V VSTEM A/V VSTEM A/V VSTEM A/V VSTEM A/V VSTEM A/V VSTEM A/V VSTEM A/V VSTEM A/V VSTEM Command VSTEM Command VDD & GND VDD & GND Clock Monitor output.

Function Digital 1.8V Power. (Internal logic system power) Crystal oscillation input. Crystal oscillation output. Digital Ground. MPEG data output 7. MPEG data output 6. Digital Ground. MPEG data output 5. MPEG data output 4. MPEG data output 3. MPEG data output 2. MPEG data output 1. MPEG data output 0. MPEG data Request input. Data Valid output. ECC Error-sector Flag output. (L: error sector) DVD Sector Head Flag output. Data Strobe output. Interrupt Request output for Host. (L: interruption is demanded) Drive H/W Reset input. (L: reset) Digital 1.8V power for Internal logic system. Digital 3.3V Power for I/O. Transmitting serial data output to Host. Reception serial data input from Host. Clock input from Host. Drive Ready signal output. (L: ready) CD-DSP C2 Pointer output. Audio serial data output. Digital audio output. L/R Clock output. Audio Bit Clock output. External Channel clock input. External RF data input. (Logic level) SIO for RF signal processing LSI control. Latch signal output. SIO for RF signal processing LSI control. Serial data input. SIO for RF signal processing LSI control. Serial data output. SIO for RF signal processing LSI control. Serial clock output. RF O.K. Signal input. RF lack Signal input. Mirror detected signal input.(H: Mirror detected) Track cross signal input. (Logic level input) Analog Ground. Track Cross signal input. (Analog level input) RF signal input. Asymmetry Charge-pump output 0. Asymmetry Charge-pump output 1 Reference current setting terminal for Asymmetry Circuit. Analog 3.3V Power. Reference current setting terminal for Jitter Monitor Jitter Monitor output. Reference current setting terminal for data PLL. VCO offset frequency setting terminal for data PLL. Analog 1.8V Power. VCO Control voltage input terminal for data PLL. VCO Loop-filter connection terminal 1 for data PLL. VCO Loop-filter connection terminal 2 for data PLL VCO gain setting terminal for data PLL. Analog Ground. Analog Ground. AD0 Input.

PU

PD

SMT

*

*

*

D D D D D D D D D D D D D D D D D D D A A A A A A A A A A A A A

VSTEM Command VSTEM Command VSTEM Command VSTEM Command Audio I/F Audio I/F Audio I/F Audio I/F Audio I/F TEST/Monitor TEST/Monitor ASP I/F ASP I/F ASP I/F ASP I/F ASP I/F ASP I/F ASP I/F ASP I/F VDD & GND Data PLL Data PLL Data PLL Data PLL Data PLL VDD & GND Data PLL Data PLL Data PLL Data PLL VDD & GND Data PLL Data PLL Data PLL Data PLL VDD & GND VDD & GND

*

* * * *

A

ADC

38

DVD-5910/DVD-A1XV

No. 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149

Terminal Name AD1 AD2 AVDD33 AD3 AD4 AD5 AD6 AD7 AD8 AD9 VREFH VREFL AVDD18 AVDD33 DA0 (TSCON) DA1 (SLED) DA2 (FSCON) DA3 (SLED2_ TILT) AVSS FG SPWM1 SPWM2 GPWM0 GPWM1 GPWM2 GPWM3 GPWM4 GPWM5 XLCAS XUCAS XMOE RA11 RA10 DVSS RA9 RA8 RA7 RA6 RA5 DVDD33 RA4 RA3 RA2 RA1 DVDD18 RA0 XRAS XMWR RD7 RD6 DVSS RD5 RD4 RD3 RD2 RD1 RD0 RD15

I/O I I P I I I I I I I I/O I/O P P O O O O P I O O O O O O O O O O O O O P O O O O O P O O O O P O O O I/O I/O P I/O I/O I/O I/O I/O I/O I/O

A/D A A A A A A A A A A A

Classification ADC ADC VDD & GND ADC ADC ADC ADC ADC ADC ADC ADC ADC VDD & GND VDD & GND AD1 Input. AD2 Input. Analog 3.3V Power. AD3 Input. AD4 Input. AD5 Input. AD6 Input. AD7 Input. AD8 Input. AD9 Input.

Function

PU

PD

SMT

Max Reference Voltage input for ADC. (Internal Reference Voltage mode, it will be an output state) Min Reference Voltage input for ADC. (Internal Reference Voltage mode, it will be an output state) Analog 1.8V Power. Analog 3.3V Power. DA0 output. (Track Servo output) DA1 output. (Sled Servo output) DA2 output. (Forcus Servo output) DA3 output. (Sled Servo / Tilt Servo output) Analog Ground FG signal input. Spindle motor PWM output 1. Spindle motor PWM output 2. Multi-purpose PWM output 0. Multi-purpose PWM output 1. Multi-purpose PWM output 2. Multi-purpose PWM output 3. Multi-purpose PWM output 4. Multi-purpose PWM output 5. DRAM LCAS output. (Low-Byte row address strobe output) DRAM UCAS output. (Upper-Byte row address strobe output) DRAM output enable. DRAM address output terminal 11. DRAM address output terminal 10. Digital Ground. DRAM address output terminal 9. DRAM address output terminal 8. DRAM address output terminal 7. DRAM address output terminal 6. DRAM address output terminal 5. Digital 3.3V Power. (for I/O) DRAM address output terminal 4. DRAM address output terminal 3. DRAM address output terminal 2. DRAM address output terminal 1. Digital 1.8V Power. (for Internal Logic power) DRAM address output terminal 0. DRAM RAS output. (Column address strobe output) DRAM Write enable. DRAM data input/output terminal 7. DRAM data input/output terminal 6. Digital Ground. DRAM data input/output terminal 5. DRAM data input/output terminal 4. DRAM data input/output terminal 3. DRAM data input/output terminal 2. DRAM data input/output terminal 1. DRAM data input/output terminal 0. DRAM data input/output terminal 15. * * * * * * * * * *

A A A A

DAC DAC DAC DAC VDD & GND

D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D

SPM SPM SPM General PWM General PWM General PWM General PWM General PWM General PWM DRAM I/F DRAM I/F DRAM I/F DRAM I/F DRAM I/F VDD & GND DRAM I/F DRAM I/F DRAM I/F DRAM I/F DRAM I/F VDD & GND DRAM I/F DRAM I/F DRAM I/F DRAM I/F VDD & GND DRAM I/F DRAM I/F DRAM I/F DRAM I/F DRAM I/F VDD & GND DRAM I/F DRAM I/F DRAM I/F DRAM I/F DRAM I/F DRAM I/F DRAM I/F

39

DVD-5910/DVD-A1XV

No. 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208

Terminal Name RD14 RD13 RD12 RD11 RD10 RD9 DVDD18 DVDD33 RD8 TEST0 TEST1 TEST2 TEST3 TEST4 TEST5 TEST6 TEST7 TEST8 TEST9 TEST10 TEST11 TEST12 TEST13 TEST14 TEST15 MODSEL0 MODSEL1 DVSS MODSEL2 GIO0 GIO1 GIO2 GIO3 DVDD33 GIO4 GIO5 GIO6 GIO7 DVDD18 GIO8 GIO9 GIO10 GIO11 GIO12 DVSS GIO13 GIO14 GIO15 GIO16 GIO17 GIO18 GIO19 TRST TMS TDI TCK TDO VMCHG DVDD18

I/O I/O I/O I/O I/O I/O I/O P P I/O O O O O O O O O O O O O O O O O I I P I I/O I/O I/O I/O P I/O I/O I/O I/O P I/O I/O I/O I/O I/O P I/O I/O I/O I/O I/O I/O I/O I I I I O I P

A/D D D D D D D

Classification DRAM I/F DRAM I/F DRAM I/F DRAM I/F DRAM I/F DRAM I/F VDD & GND VDD & GND

Function DRAM data input/output terminal 14. DRAM data input/output terminal 13. DRAM data input/output terminal 12. DRAM data input/output terminal 11. DRAM data input/output terminal 10. DRAM data input/output terminal 9. Digital 1.8V Power. (for internal Logic system) Digital 3.3V power for I/O. DRAM data input/output terminal 8. TEST I/O 0. TEST I/O 1. TEST I/O 2. TEST I/O 3. TEST I/O 4. TEST I/O 5. TEST I/O 6. TEST I/O 7. TEST I/O 8. TEST I/O 9. TEST I/O 10. TEST I/O 11. TEST I/O 12. TEST I/O 13. TEST I/O 14. TEST I/O 15. TEST mode select 0. (GND, under normal conditions) TEST mode select 1. (GND, under normal conditions) Digital Ground. TEST mode select 2. (GND, under normal conditions) Multi-purpose port 0. Multi-purpose port 1. Multi-purpose port 2. Multi-purpose port 3. Digital 3.3V Power for I/O. Multi-purpose port 4. Multi-purpose port 5. Multi-purpose port 6. Multi-purpose port 7. Digital 1.8V Power for I/O. (for internal Logic system) Multi-purpose port 8. Multi-purpose port 9. Multi-purpose port 10. Multi-purpose port 11. Multi-purpose port 12. Digital Ground. Multi-purpose port 13. Multi-purpose port 14. Multi-purpose port 15. Multi-purpose port 16. Multi-purpose port 17. Multi-purpose port 18. Multi-purpose port 19. JTAG Reset input. JTAG Mode Select input. JTAG Data Input. JTAG Clock input. JTAG Data output. VSTEM / external MCU access selection terminal of system setting register for DSP. (L: VSTEM, H: external MCU) Digital 1.8V power for internal Logic system.

PU * * * * * *

PD

SMT

D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D

DRAM I/F TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor TEST/Monitor VDD & GND TEST/Monitor Multi-purpose Multi-purpose Multi-purpose Multi-purpose VDD & GND General Port General Port General Port General Port VDD & GND General Port General Port General Port General Port General Port VDD & GND Multi-purpose General Port General Port General Port General Port General Port General Port JTAG I/F JTAG I/F JTAG I/F JTAG I/F JTAG I/F MCU I/F VDD & GND

*

* * * * * * * * * * * * * * * * * * * * * * * * * * * * *

* * * * * * * * * * * * * * * * * * * * * * *

40

VEE HA2/AUX4[4] VEE I2CDATA/AUX[0] I2C_CLK/AUX[1] AUX[2]/IOW# VSS VEE AUX[3]/IOR# AUX[4] AUX[5] AUX[6] AUX[7] LOE# VSS VCC LCS0# LCS1# LCS2# LCS3# VSS LD0 LD1 LD2 LD3 LD4 VEE VSS LD5 LD6 LD7 LD8 LD9 LD10 LD11 VSS VEE LD12 LD13 LD14 LD15 LWRLL# LWRHL# VSS VEE CAMIN0 CAMIN1 LA0 LA1 LA2 LA3 VSS

PINOUT DIAGRAM

ES6138F (MA: IC108)

157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208

ES6138F

41

VEE LA4 LA5 LA6 LA7 LA8 LA9 VSS VCC LA10 LA11 LA12 LA13 LA14 LA15 LA16 VSS VEE LA17 LA18 LA19 LA20 LA21 RESET# TDMDX/RSEL VSS VEE TDMDR TDMCLK TDMFS TDMTSC# TWS/SEL_PLL2 TSD0/SEL_PLL0 VSS VCC TSD1/SEL_PLL1 TSD2 TSD3 MCLK TBCK SEL_PLL3/SPDIF_OUT SPDIF_IN VSS VCC RSD RWS RBCK NC XIN XOUT AVEE AVSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 VEE VSS DSCK DQM DCS0# VEE VSS DCS1# DB15 DB14 DB13 DB12 VEE VSS DB11 DB10 DB9 DB8 DB7 DB6 VSS VCC DB5 DB4 DB3 DB2 DB1 DB0 VSS VEE DMBS1 DMBS0 DRAS# DWE# DOE#/DSCK_EN DCAS# VEE VSS DMA11 DMA10 DMA9 DMA8 DMA7 DMA6 VSS VEE DMA5 DMA4 DMA3 DMA2 DMA1 DMA0

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

DVD-5910/DVD-A1XV

DVD-5910/DVD-A1XV

ES6138F Pin DescriptionName VEE Pin Numbers 1,18, 27, 59, 68, 75, 92, 99, 104, 130, 148, 157, 159, 164, 183, 193, 201 2:7, 10:16, 19:23, 204:207 8, 17, 26, 34, 43, 60, 67, 76, 84, 91, 98, 103, 120, 129, 138, 147, 156, 163, 171, 177, 184, 192, 200, 208 9, 35, 44, 83, 121, 139, 172 24 I/O Definition

P

I/O power supply.

LA[21:0] VSS

O

RISC port address bus.

G

Ground.

VCC RESET# TDMDX RSEL

P I O I

Core power supply. Reset input (active-low). TDM transmit data output. LCS3 ROM Boot Data Width Select. Strapped to VCC or ground via 4.7-k resistor; read only during reset. RSEL 0 1 Selection 16-bit ROM 8-bit ROM

25

TDMDR TDMCLK TDMFS TDMTSC# TWS SEL_PLL2

28 29 30 31

I I I O O I

TDM receive data input. TDM clock input. TDM frame sync input. TDM output enable (active-low). Audio transmit frame sync output. System and DSCK output clock frequency selection is made at the rising edge of RESET#. The matrix below lists the available clock frequencies and their respective PLL bit settings. Strapped to VCC or ground via 4.7-k resistor; read only during reset. SEL_PLL2 0 SEL_PLL1 0 0 1 1 0 0 1 1 SEL_PLL0 0 1 0 1 0 1 0 1 PLL Settings DCLK 4.5 DCLK 5.0 Bypass DCLK 4.0 DCLK 4.25 DCLK 4.75 DCLK 5.5 DCLK 6.0

32

0 0 0 1 1 1 1

42

DVD-5910/DVD-A1XV

ES6138F Pin Description (Continued)Name TSD0 33 SEL_PLL0 TSD1 36 SEL_PLL1 TSD2 TSD3 NC MCLK TBCK SEL_PLL3 37 38 48 39 40 I O O I/O O I Refer to the description and matrix for SEL_PLL2 pin 32. Audio transmit serial data output 2. Audio transmit serial data output 3. No connect pins. Leave open. Audio master clock for audio DAC. Audio transmit bit clock. Clock source select. Strapped to VCC or ground via 4.7-k resistor; read only during reset. SEL_PLL3 41 0 1 Clock Source Crystal oscillator DCLK input I O Refer to the description and matrix for SEL_PLL2 pin 32. Audio transmit serial data port 1. Pin Numbers I/O O Definition Audio transmit serial data port 0.

SPDIF_OUT SPDIF_IN RSD RWS RBCK XIN XOUT AVEE AVSS DMA[11:0] DCAS# DOE# 70 DSCK_EN DWE# DRAS# DMBS0 DMBS1 DB[15:0] DCS[1:0]# DQM 71 72 73 74 77:82, 85:90, 93:96 97,100 101 42 45 46 47 49 50 51 52 53:58, 61:66 69

O I I I I I O P G O O O O O O O O I/O O O

S/PDIF output. S/PDIF input. Audio receive serial data. Audio receive frame sync. Audio receive bit clock. 27-MHz crystal input. 27-MHz crystal output. Analog power for PLL. Analog ground for PLL. DRAM address bus. DRAM column address strobe. DRAM output enable (active-low). DRAM clock enable. DRAM write enable (active-low). DRAM row address strobe (active-low). DRAM bank select 0. DRAM bank select 1. DRAM data bus. DRAM chip select (active-low). Data input/output mask.

43

DVD-5910/DVD-A1XV

ES6138F Pin Description (Continued)Name DSCK DCLK YUV0 CAMIN2 UDAC Pin Numbers 102 105 I/O O I O I O Definition Output clock to DRAM. Clock input to PLL. YUV pixel 2 output data. Camera YUV 2. Video DAC output. Pin Value 0 1 2 3 4 5 6 106 7 8 9 10 11 12 13 14 N/A CVBS/Chroma CVBS CVBS N/A CVBS/Chroma CVBS/Chroma Chroma SYNC Chroma CVBS1 CVBS1 SYNC N/A CVBS1 Y G Y G G G Y Y G B Pb B R R Pr Pr R R Pr R B B Pb Pb B 115 F DAC CVBS/Chroma CVBS/Chroma CVBS/Chroma CVBS/Chroma CVBS/Chroma CVBS/Chroma CVBS/Chroma 114 V DAC CVBS1 CVBS1 N/A CVBS1 CVBS1 CVBS1 N/A 113 Y DAC Y Y Y N/A N/A Y Y 108 C DAC C C C N/A N/A Pb Pb 106 U DAC N/A CVBS2 N/A CVBS2 N/A Pr Pr

F: CVBS/chroma signal for simultaneous mode. Y: Luma component for YUV and Y/C processing. C: Chrominance signal for Y/C processing. U: Chrominance component signal for YUV mode. V: Chrominance component signal for YUV mode. YUV1 107 VREF YUV2 108 CDAC YUV3 109 COMP YUV4 110 RSET ADVEE 111 I P DAC current adjustment resistor input. Analog power for video DAC. I O Compensation input. Bypass to ADVEE with 0.1-F capacitor. YUV pixel 4 output data. O O Video DAC output. Refer to description and matrix for UDAC pin 106. YUV pixel 3 output data. I O Internal voltage reference to video DAC. Bypass to ground with 0.1-F capacitor. YUV pixel 2 output data. O YUV pixel 1 output data.

44

DVD-5910/DVD-A1XV

ES6138F Pin Description (Continued)Name ADVSS YUV5 113 YDAC YUV6 114 VDAC YUV7 FDAC CAMIN3 PCLK2XSCN 116 CAMIN4 PCLKQSCN CAMIN5 AUX3[2] VSYNC# CAMIN6 AUX3[1] HSYNC# CAMIN7 AUX3[0] HD[5:0] DCI[5:0] AUX1[5:0] HD6 DCI6 128 AUX1[6] VFD_DOUT HD7 DCI7 131 AUX1[7] VFD_DIN HD8 DCI_FDS# 132 AUX2[0] VFD_CLK I/O I Aux2 data I/O. VFD clock input. I/O I I/O I/O Aux1 data I/O. VFD data input. Host data bus line 8. DVD input sector start (active-low). I/O I I/O I/O Aux1 data I/O. VFD data output. Host data bus line 7. DVD channel data I/O. 122:127 119 118 117 I O I I/O I/O I I/O I/O I I/O I/O I/O I/O I/O I/O Camera YUV 4. 13.5-MHz video output pixel clock. Camera YUV 5. Aux3 data I/O. Vertical sync (active-low). Camera YUV 6. Aux3 data I/O. Horizontal sync (active-low). Camera YUV 7. Aux3 data I/O. Host data bus lines 5:0. DVD channel data I/O. Aux1 data I/O. Host data bus line 6. DVD channel data I/O. 115 O O O I I/O Video DAC output. Refer to description and matrix for UDAC pin 106. YUV pixel 7 output data. Video DAC output. Refer to description and matrix for UDAC pin 106. Camera YUV 3. 27-MHz video output pixel clock. O O Video DAC output. Refer to description and matrix for UDAC pin 106. YUV pixel 6 output data. Pin Numbers 112 I/O G O Definition Analog ground for video DAC. YUV pixel 5 output data.

45

DVD-5910/DVD-A1XV

CXD2753R (MA: IC405) ( )Pin Assignment

Block Diagram

46

DVD-5910/DVD-A1XV PIN DescriptionPin Name 1 VSC I/O I I I O O O I Ipd I O O O O O O O O O O O O I Ipu O Ipu Ipu I I I O O O O O O O O O O O It fixed to ground.( for Core) Latch input for COM serial communication. Shift clock input for COM serial communication. Data input for COM serial communication. +2.5V Power for Core. Data output for COM serial communication. Hi-Z potential except the output mode. Completion flag of output preparation for COM serial communication. L is outputted at the time of completion. Output enable pin for COM serial communication. L is outputted at the time of MSDATO mode. Reset pin. The whole IC is reset by at the time of L potential. Soft Mute. Soft mute of the audio output is carried out at the time of H potential. It releases at the time of L potential. Master Clock input. It fixed to Ground. Ground for I/O. External output Clock 1. External output Clock 2. 44.1kHz, 1Fs Clock output. Frame signal output. +3.3V Power for I/O. Monitor output. Monitor output. Monitor output. Monitor output. Output terminal for a Test. (open) Output terminal for a Test.(open) Output terminal for a Test.(open) Output terminal for a Test.(open) Clock input for a Test. It fixed to L potential. Input pin(pull-up) for a Test.(open) It fixed to Ground. Ground for CORE. Output for a Test.(open). Input pin(pull-up) for a Test.(open) Reset pin(pull-up) for a Test. Input the Power-on reset signal or fixed to L potential. Test input pin. It fixed to L potential. Test input pin. It fixed to L potential. Test input pin. It fixed to L potential. +2.5V Power for CORE. Out put for TEST. It fixed to open. DST monitor. Supplementary data output. (LSB) Supplementary data output. Supplementary data output. Supplementary data output. Ground for I/O. Supplementary data output. Supplementary data output. +3.3V Power for I/O. Supplementary data output. Supplementary data output. (MSB) Supplementary data Acknowledge output terminal. Ground for CORE. Functions

2 XMSLAT 3 MSCK

4 MSDATI 5 VDC 6 7 8 9 10 11 12 13 14 15 16 MSDATO MSREADY XMSDOE XRST SMUTE MCKI VSIO EXCKO1 EXCKO2 LRCK FRAME

17 VDIO 18 19 20 21 MNT0 MNT1 MNT2 MNT3

22 TESTO 23 24 25 TESTO TESTO TESTO

26 TCK 27 TDI 28 29 VSC TDO

30 TMS 31 32 33 34 35 36 37 38 39 40 41 42 43 44 TRST TEST1 TEST2 TEST3 VDC TESTO XBIT SUPDT0 SUPDT1 SUPDT2 SUPDT3 VSIO SUPDT4 SUPDT5

45 VDIO 46 47 48 49 SUPDT6 SUPDT7 XSUPAK VSC

47

DVD-5910/DVD-A1XV

Pin Name 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 TESTO TESTI TESTI TESTO VDC DSADML DSADMR BCKASL VSDSD BCKAI BCKAO PHREFI PHREFO ZDFL DSAL ZDFR DSAR VDDSD ZDFC DSAC ZDFLFE DSASW VSDSD ZDFLS DSALS ZDFRS DSARS VDDSD IOUT0 IOUT1 VSC IOUT2 IOUT3 VDC IOUT4 IOUT5 VSIO IANCO

I/O O I I O O O I I O I O O O O O O O O O O O O O O O O O O O O O I I O O O I Output for TEST. (open) Input for TEST. It fixed to L potential. Input for TEST. It fixed to L potential. Output for TEST. (open) +2.5V Power for CORE. DSD Data output terminal for Lch Down Mix. DSD Data output terminal for Rch Down Mix.

Functions

I/O selection terminal of the Bit clock for DSD data output. L=input (Slave), H=output (Master) Ground terminal for DSD data output. Bit clock input terminal for DSD data output. Input a Bit clock into this terminal at the time of BCKASL=L potential. Bit clock output terminal for DSD data output. Bit clock output from this terminal at the time of BCKASL=H potential. Reference phase signal input terminal for DSD output phase modulation. Reference phase signal output terminal for DSD output phase modulation. Lch zero-data detection flag (at the time of com setup). It will be set to H if non-sound data continues 300 msecs. DSD data output terminal for Lch speaker. Rch zero-data detection flag (at the time of com setup). It will be set to H if non-sound data continues 300 msecs. DSD data output terminal for Rch speaker. +3.3V Power for DSD data output. Cch zero-data detection flag (at the time of com setup). It will be set to H if non-sound data continues 300 msecs. DSD data output terminal for Cch speaker. LFEch zero-data detection flag (at the time of com setup). It will be set to H if non-sound data continues 300 msecs. DSD data output terminal for SWch speaker. Ground for DSD data output. LSch zero-data detection flag (at the time of com setup). It will be set to H if non-sound data continues 300 msecs. DSD data output terminal for LSch speaker. RSch zero-data detection flag (at the time of com setup). It will be set to H if non-sound data continues 300 msecs. DSD data output terminal for RSch speaker. +3.3V Power for DSD data output. Data output terminal 0 for IEEE1394 link chip I/F. Data output terminal 1 for IEEE1394 link chip I/F. Ground for CORE. Data output terminal 2 for IEEE1394 link chip I/F. Data output terminal 3 for IEEE1394 link chip I/F. +2.5V Power for CORE. Data output terminal 4 for IEEE1394 link chip I/F. Data output terminal 5 for IEEE1394 link chip I/F. Ground for I/O. Transmission information data output terminal for IEEE1394 link chip I/F. Data transmission hold request signal input terminal for IEEE1394 link chip I/F. High speed transmission request signal input terminal for IEEE1394 link chip I/F. +3.3V Power for I/O. Frame reference signal output terminal for IEEE1394 link chip I/F. Enable signal output terminal for IEEE1394 link chip I/F. Data transmission clock output terminal for IEEE1394 link chip I/F. Ground for CORE. TEST input terminal. It fixed to H potential.

88 IFULL 89 IEMPTY

90 VDIO 91 IFRM

92 IOUTE 93 94 95 IBCK VSC TESTI

48

DVD-5910/DVD-A1XV

Pin Name 96 TESTI

I/O I Ipu O I I I I I I I I I I I I I I I I I I I Ai Ai I/O I/O I/O I/O I/O I/O I/O I/O O O O O O O TEST input terminal. It fixed to L potential. TEST input terminal. It fixed to H potential. TEST output terminal. (open) +2.5V Power for CORE. TEST input terminal. It fixed to L potential. TEST input terminal. It fixed to L potential. TEST input terminal. It fixed to L potential. TEST