development and evaluation of a removable and portable strain sensor for short-term live
TRANSCRIPT
Development and Evaluation of a Removable and Portable Strain
Sensor for Short-term Live Loading of Bridge Structures
By
Carl L. Schneeman, B.S.C.E.
A Thesis submitted to the Faculty of the Graduate School, Marquette University, in
Partial Fulfillment of the Requirement for the Degree of
Master of Science
Milwaukee, Wisconsin
2006
i
Preface
Historically, bridges have been constructed in many different ways. As economic
conditions change, so do the materials and methods used in construction. To evaluate the
use of new materials for these structures, research and development is conduced to
determine their adequacy in modern construction. However, long-term results are
required for analysis of bridges, as they are constructed to remain in service for extended
periods of time. Additionally, a fundamental understanding and proper selection of the
tools used in bridge monitoring is required.
This thesis presents a detailed discussion of the state of bridge monitoring,
development and operation of a removable strain sensor to be used in collecting data on
bridge structures, and guidelines for a future load test of a bridge in northern Wisconsin.
Observations and conclusions of the study are made as well, with recommendations for
future work on this topic.
ii
Acknowledgements
I would like to thank the many people who have helped in numerous ways
throughout my tenure at Marquette. Without their support and help none of this work
would have been possible.
The members of my advisory committee have been wonderful. Dr. Chris Foley
has been a tireless and selfless mentor to me. Never before have I worked with an
individual so passionate and dedicated. His constant drive to teach others has benefited
me countless ways. Drs. Stephen Heinrich and Baolin Wan both were extremely helpful
in my classes and during my thesis work.
The many people working for the laboratories of Marquette need to be
recognized. Dave Newman has been an instrumental person for me. His frequent
questions, new challenges, and often used humor have helped shape my education in so
many positive ways. Our students are fortunate to have such a wealth of experience to
learn from. Tom Silman’s help and guidance requires thanks also. Without his tireless
flexibility my late hours in the machine shop would not have been possible.
Additionally, John Boudnik’s willingness to help at any time is much appreciated.
To those in the working world who have shown me what being a professional
means. Many thanks are directed to John Pluta at MSI General, who was the first to truly
show me how to be an engineer. The generosity of Victory Steel of Milwaukee and
Construction Supply & Errection of Germantown, WI are to be commended – their
willingness to aid the university is instrumental to our successes.
Thanks are also due to so many people who have pushed me to go beyond what is
required. People like Andy Basta, Nick Hornyak, Kristine Martin, Panchito Ojeda, Brian
iii
Porter, and Danny Stadig, have been a mainstay for me. Their support, suggestions and
assistance in all aspects of life have left are truly valued.
Many thanks are due to my girlfriend, Meg Taylor. She has been a pillar of
stability for me, constantly supporting me in my endeavors.
Finally, my family has also been wonderful. My parents, Chris and Cathy, and
siblings, Pat, Dan, Matt and Lucy, have always provided me with endless support. How
they have sustained my many engineering lectures and overly-scientific explanations of
daily occurrences is amazing.
iv
Table of Contents
1. Introduction and Summary of Work
1.0 Introduction……………………………………………………………………. 1
1.1 The De Neveu Creek IBRC Bridge…………………………………………… 3
1.2 Objective of Thesis…………………………………………………………… 6
1.3 Scope of Thesis………………………………………………………………... 7
2. Literature Review and Synthesis
2.0 Introduction …………………………………………………………………… 8
2.1 Instrumentation Guidelines…………………………………………………… 8
2.2 The De Neveu Creek IBRC Bridge …………………………………………... 13
2.2.1. FRP Reinforcement in the De Neveu Bridge…………………………... 15
2.2.2. Development and Testing of the FRP-grillage Reinforced Deck ……... 17
2.3 Load Testing of the De Neveu Creek Bridge ………………………………… 20
2.3.1. Strain Gage Instrumentation of the Bridge ……………………………. 21
2.3.2. In-Situ Load Test of B-20-148 FRP Bridge …………………………… 23
2.3.3. In-Situ Load Test of B-20-149 Conventional Bridge …………………. 26
2.3.4. Results of B-148 and B-149 Load Tests ………………………………. 27
2.4 Ohio Bridge HAM-126-0881 ………………………………………………… 31
2.4.1. Data Acquisition System Employed …………………………………... 32
2.4.2. Load Testing and Results ……………………………………………… 34
2.5 South Carolina Route S655 …………………………………………………... 37
2.5.1. GFRP Panels …………………………………………………………... 38
2.5.2. Instrumentation and Load Testing …………………………………….. 40
2.6 Fairground Road Bridge ……………………………………………………… 44
2.6.1. Study of Composite Action and Strain Measurements ……………….. 45
2.6.2. Load Testing and Results………………………………………………. 46
2.7 The Bridge Street Bridge……………………………………………………… 50
2.7.1. Materials Used ………………………………………………………… 51
2.7.2. Instrumentation ………………………………………………………... 52
2.7.3. Load Test and Results …………………………………………………. 53
2.8 Synthesis of Literature ………………………………………………………... 55
v
3. Data Acquisition and Strain Measurement
3.0 Introduction …………………………………………………………………… 59
3.1 Signal Processing ……………………………………………………………... 59
3.1.1. Analog to Digital Conversion ………………………………………… 60
3.1.2. Sampling Rates………………………………………………………… 63
3.1.3. Signal Amplification…………………………………………………… 64
3.1.4. Signal Filtering………………………………………………………… 69
3.2 Measurement with Electrical Resistance Strain Gages ………………………. 75
3.3 Strain Gage Measurement Errors …………………………………………….. 83
3.4 String Potentiometers and Linear Position Sensors …………………………... 90
3.5 DASYLab Data Acquisition Software ……………………………………….. 93
3.5.1. Installation of ADC Modules …………………………………………. 96
3.5.2. Installation of Digital Filtering ………………………………………... 99
3.5.3. The Black Box Module ………………………………………………... 102
3.5.4. Offset Adjustment of Signals………………………………………….. 104
3.5.5. Establishment of Calibration Modules …………………………………108
3.5.6. Continuous Unit Conversion ………………………………………….. 113
3.5.7. Duplicating the Black Box for use with Transducers ………………… 115
3.5.8. Configuring the Black Box for Use with Different Channels…………. 117
4. Development and Testing of a Portable Strain Sensor
4.0 Introduction …………………………………………………………………… 123
4.1 Quarter Bridge Circuit Selection ……………………………………………... 124
4.2 Material Experimentation and Selection ……………………………………... 127
4.3 Description of Portable Strain Sensor ………………………………………… 130
4.4 Anchorage of the Sensor ……………………………………………………… 133
4.5 Laboratory Validation…………………………………………………………. 135
4.5.1. Torque Level Tests ……………………………………………………. 140
4.5.2. Evaluation of Washer Presence………………………………………... 142
4.5.3. Excitation Voltage Evaluation…………………………………………. 143
4.6 Finite Element Analysis ………………………………………………………. 144
4.6.1. Finite Element Model of Test Beam …………………………………... 145
vi
4.6.2. Finite Element Model of Strain Sensor ……………………………….. 149
4.7 Calibration of Individual Strain Sensors for Field Implementation ………….. 163
4.7.1. Calibration Method and Equipment Used………………………………163
4.7.2. Data Recorded during Load Tests …………………………………….. 166
4.7.3. Individual Calibration Factors…………………………………………. 169
5. Proposed Load Test
5.0 Introduction …………………………………………………………………… 171
5.1 Load Test Objectives and Instruments………………………………………... 171
5.2 Permanently Installed Equipment……………………………………………... 177
5.2.1. Lead Wiring for Instruments…………………………………………… 177
5.2.2. Enclosure Box and Screw Terminals…………………………………... 180
5.2.3. Installation of Strain Sensors…………………………………………... 184
5.3 Load Test Vehicles and Test Configuration…………………………………... 187
5.3.1. Load Test Objectives…………………………………………………... 188
5.3.2. Load Test Configurations……………………………………………… 189
5.4 Data Acquisition System……………………………………………………… 193
5.4.1. Signal Conditioning Modules………………………………………….. 196
5.4.2. Connection to Strain Gage Modules…………………………………… 198
5.4.3. Acquisition Software…………………………………………………... 200
5.4.4. Error Correction in Readings…………………………………………... 201
6. Summary and Conclusions
6.0 Summary……………………………………………………………………… 203
6.1 Conclusions…………………………………………………………………… 204
6.2 Recommendations for Future Research………………………………………. 206
References……………………………………………………………………………… 210
Appendix A…………………………………………………………………………….. 214
Appendix B……………………………………………………………………………..235
Appendix C……………………………………………………………………………..241
Appendix D……………………………………………………………………………..244
vii
List of Figures
Figure 1.1.1 – Wisconsin Highways 151 before (left) the bypass and after (right) 4
Figure 1.1.2 – The De Neveu Creek Bridge 5
Figure 2.2.1 – The De Neveu Creek Bridge, WI B-20-148 14
Figure 2.2.2 – Cross section of the De Neveu Creek Bridge 15
Figure 2.2.3 – Assembled FRP grillage 15
Figure 2.2.4 – Cross sections of FRP materials used 16
Figure 2.2.5 – Simple-span slab tests 19
Figure 2.2.6 – Restrained end slab tests 19
Figure 2.3.1 – Layout of surveying prisms and strain gages 21
Figure 2.3.2 – Strain gage locations 22
Figure 2.3.3 – Strain gage locations 22
Figure 2.3.4 – Stopped vehicle locations for live-load testing of B-20-148 FRP 25
Figure 2.3.5 – Stopped vehicle locations for live-load testing of
B-20-149 Conventional 27
Figure 2.3.6 – Deflection plot of mid-span girder response in bridge B-20-148 FRP 28
Figure 2.3.7 – Deflection plot of mid-span girder response in bridge B-20-149
Conventional 29
Figure 2.4.1 – Schematic of Ohio Bridge HAM-126-0881 32
Figure 2.4.2 – Static live-load Cases A through L 35
Figure 2.4.3 – Method for calculating internal moments in stingers 37
Figure 2.5.1 – Individual Duraspan® deck panels 39
Figure 2.5.2 – Section of bridge deck and integral grout-filled shear pockets 39
Figure 2.5.3 – Instrument layout of S655 Bridge 41
Figure 2.5.4 – Live-load test cases for S655 Bridge 42
Figure 2.6.1 – Instrumentation layout of the Fairground Road Bridge 46
Figure 2.6.2 – Bridge Diagnostics Strain Transducer 46
Figure 2.6.2 – Method used to locate the neutral axis of stringers 48
Figure 2.6.3 – Comparison of composite nature stress profiles through a typical deck
section 48
viii
Figure 2.6.4 – Top flange tensile “spike” observed in stringers during live load
testing 49
Figure 2.7.1 – Bridge Street Bridge cross section 51
Figure 2.7.2 – Strain gage location in instrumented spans of Structure B 52
Figure 2.7.3 – Long-term instrumented spans of Structure B 53
Figure 2.7.4 – Live-load test cases for Bridge Street Bridge 54
Figure 3.1.1 – Layout of a typical data acquisition system 60
Figure 3.1.2 – Application of the Nyquist Theorem 63
Figure 3.1.3 – Block diagram of an IOTech DBK43A 66
Figure 3.1.4 – Signal path of the “OFFSET” trimpot 67
Figure 3.1.5 – Signal path during adjustment of the input amplifier gain 68
Figure 3.1.6 – Signal path during adjustment of the scaling amplifier gain 69
Figure 3.1.7 – Typical low-pass frequency response 70
Figure 3.1.8 – Butterworth low-pass filter response 71
Figure 3.1.9 – Chebyshev low-pass filter response 71
Figure 3.1.10 – Comparison of filtered (b & c) and unfiltered data (a) 72
Figure 3.1.11 – (a) standard wave composed of AC and DC signals, (b) AC
Coupled wave 73
Figure 3.2.1 – Typical strain gage 76
Figure 3.2.2 – The Wheatstone bridge 76
Figure 3.2.3 – Typical configurations of the Wheatstone bridge 77
Figure 3.2.4 – Diagram of variables used in calculations 78
Figure 3.2.5 – Simulated strain via shunt calibration 80
Figure 3.3.1 – Quarter bridge strain gage configurations 84
Figure 3.3.2 – Nonlinearity errors for tensile strains in bridge circuits 89
Figure 3.4.1 – Circuit diagram of a typical three-wire transducer 91
Figure 3.4.2 – 30-inch String Potentiometer 92
Figure 3.4.3 – 4-inch Linear Position Sensor 92
Figure 3.4.4 – Linear calibration of sensors 93
Figure 3.5.1 – Data acquisition worksheet 94
Figure 3.5.2 – Logical map of software configuration 95
ix
Figure 3.5.3 – Hardware configuration window 97
Figure 3.5.4 – Hardware configuration window on the main worksheet 98
Figure 3.5.5 – Expansion of analog inputs in the DBK43A module 99
Figure 3.5.6 – Defining global variables 100
Figure 3.5.7 – Defining filtration properties for each channel within the filter
module dialog box 101
Figure 3.5.8 – ADC and filter modules connected on the worksheet 101
Figure 3.5.9 – Locating a new black box on the main worksheet (left) and opening
the black box (right) 102
Figure 3.5.10 – Modules installed in the black box 104
Figure 3.5.11 – Offset adjust modules and digital meter in black box 105
Figure 3.5.12 – Specification of the Switch module operation 106
Figure 3.5.13 – Specification of the Action module operation 107
Figure 3.5.14 – Specification of the Digital Meter module operation 108
Figure 3.5.15 – Linear scaling from shunt calibration 109
Figure 3.5.16 – Locating the Linear Scaling/Unit Conversion module on the black
box worksheet 110
Figure 3.5.17 – Flow chart depicting the signal path while acquiring simulated
strain voltages from shunt calibration 111
Figure 3.5.18 – Storing global variables for calibration 112
Figure 3.5.19 – Setting linear scaling values for individual strain gages 114
Figure 3.5.20 – Signal path of completed black box worksheet for linear scaling 114
Figure 3.5.21 – Saving the active black box for future applications 115
Figure 3.5.22 – Flow of dialog boxes while saving a black box for future use 116
Figure 3.5.23 – Modified black box for DBK65 transducer channels 117
Figure 3.5.24 – Modifications of the black box for DBK65 transducer channels 119
Figure 3.5.25 – Signal path from the black boxes to the Write Data module 120
Figure 3.5.26 – Specifying data recording options 120
Figure 3.5.27 – Overview of completed worksheet 122
Figure 4.1.1 – Quarter bridge circuit used during laboratory experimentation
with the DaqBook 2000 system 126
x
Figure 4.1.2 – Completion resistor plug installed in the DBK43A module with top
cover removed 127
Figure 4.2.1 – Strain sensor with quarter bridge strain gage composed of nylon 128
Figure 4.2.2 – Carbon-fiber strain sensor with quarter bridge strain gage (a)
and installation (b) 128
Figure 4.2.3 – Recorded strain levels in carbon-fiber strain sensor and bonded
strain gage 129
Figure 4.3.1 – Final configuration of the strain sensor 131
Figure 4.3.2 – Constructed strain sensors without connection tabs or protective
Coating 132
Figure 4.4.1 – Field installation of the strain sensor to concrete 134
Figure 4.4.2 – Ovalization of a bolt hole under loading 134
Figure 4.5.1 – Four-point bending test used for strain sensor evaluation 135
Figure 4.5.2 – Dimensioned constant-moment beam testing schematic 135
Figure 4.5.3 – Mid-span layout of Strain sensors and complementary strain gages 138
Figure 4.5.4 – Strain sensors installed for the constant-moment beam test 139
Figure 4.5.5 – Complementary strain gages installed on the opposite flange as
Strain sensors for the constant-moment beam test 139
Figure 4.5.6 – Deformed region of washer contact due to tightening the anchorage
nuts to 180 lb-in 142
Figure 4.5.7 – Half bridge temperature compensating circuit 144
Figure 4.6.1 – Illustration of the mapped meshing procedure used 145
Figure 4.6.2 – 20-node brick element used for 3D modeling 146
Figure 4.6.3 – Boundary conditions of the 3D beam model 147
Figure 4.6.4 – The extrusion process uses to build a 3D model of the sensor 150
Figure 4.6.5 – Inadequately restrained model penetrating the steel test beam 152
Figure 4.6.6 – Boundary conditions for the tensile case of sensor model 1 154
Figure 4.6.7 – Boundary conditions for the compression case of sensor model 1 154
Figure 4.6.8 – Boundary conditions for the tensile case of sensor model 2 154
Figure 4.6.9 – Boundary conditions for the compression case of sensor model 2 154
xi
Figure 4.6.10 – Ring of elements around bolt holes extruded through thickness
of sensor for sensor model 3 155
Figure 4.6.11 – Boundary conditions for the tensile case of sensor model 3 155
Figure 4.6.12 – Boundary conditions for the compression case of sensor model 3 155
Figure 4.6.13 – Boundary conditions for both compression and tensile cases
of sensor model 4 156
Figure 4.6.14 – Detail of boundary conditions imposed to simulate contact with
a washer for sensor model 4 156
Figure 4.6.15 – Boundary conditions for both compression and tensile cases
of sensor models 5 and 6 157
Figure 4.6.16 – Notch for strain relief of wires in sensor 160
Figure 4.6.17 – Longitudinal strain distribution (εy) for tension and compression
cases for the final sensor model 161
Figure 4.7.1 – Weld locations on beam members for the constant-moment load test 164
Figure 4.7.2 – Typical response of strain gages and sensors under applied loading 167
Figure 4.7.3 – Erroneous response of strain gages and sensors under rapid, non-
monotonically increasing loading 168
Figure 5.1.1 – East half of the De Neveu Creek IBRC Bridge indicating
instrument locations 172
Figure 5.1.2 – Section of girder and deck for locating strain sensors 174
Figure 5.1.3 - Composite behavior stress profiles through a typical deck section 174
Figure 5.1.4 – Section view of strain sensors for transverse wheel load distribution 175
Figure 5.1.5 – Plan view of strain sensors to monitor transverse wheel load
distribution 176
Figure 5.1.6 – String potentiometer manufactured by UniMeasure 177
Figure 5.2.1 – Plan of sealed PVC pipes containing lead wire runs for
individual instruments 178
Figure 5.2.2 – PVC piping terminating at the enclosure box 179
Figure 5.2.3 – Installation of the PVC piping housing instrument lead wires
along girder #1 179
Figure 5.2.4 – Detail of a typical screw terminal connection 180
xii
Figure 5.2.5 – Diagram of lead wires terminated in the screw terminals in the
enclosure box 181
Figure 5.2.6 – Enclosure box housing lead wire connections 181
Figure 5.2.7 – Labels for transverse strain sensors at mid-span 182
Figure 5.2.8 – Labels for girder strain profile sensors at third-span 183
Figure 5.2.9 – Labels for longitudinal strain sensors 184
Figure 5.2.10 – Illustration of the anchorage system for strain sensors 184
Figure 5.2.11 – Approximation of the force acting on the anchor rod. 186
Figure 5.3.1 – Test vehicle dimensions for UM-R/UW-M load test 187
Figure 5.3.2 – Load Test 1 test vehicle locations 190
Figure 5.3.3 – Axle positions of a single girder during Load Tests 1 and 2 191
Figure 5.3.4 – Load Test 2 test vehicle locations 192
Figure 5.3.5 – Load Test 3 test vehicle locations 193
Figure 5.4.1 – Photograph of the data acquisition system used for load testing 194
Figure 5.4.2 – Photograph of the DaqBook 2001 194
Figure 5.4.3 – Photograph of the DBK43A strain gage module with cover
panel removed 195
Figure 5.4.4 – Photograph of the DBK65 transducer module with cover panel
removed 195
Figure 5.4.5 – Analog filter locations on the DBK43A module 197
Figure 5.4.6 – Quarter Bridge circuit and completion resistor configuration for
use with the strain sensors 197
Figure 5.4.7 – Typical pin numbering of a mini-DIN plug 199
Figure 5.4.8 – Pin numbering of mini-DIN plugs used for this project with
typical color-coding 199
Figure 5.4.9 – Location of the excitation voltage jumpers on the DBK 65
circuit board 200
xiii
List of Tables
Table 2.2.1 –FRP-grillage material properties 17
Table 2.3.1 – Maximum mid-span displacement data from live load tests in bridge
B-20-148 FRP 28
Table 2.3.2 – Maximum deflection data from live load tests in bridge B-20-149
Conventional 29
Table 2.3.3 – Approximate girder distribution factors for load testing of B-20-148
FRP 30
Table 2.5.1 – Load Test #1 - Maximum load test values 43
Table 2.5.2 – Load Test #2 - Maximum load test values 43
Table 3.3.1 – Non-linearity correction factors of Wheatstone bridges 89
Table 4.2.1 – Typical modulus of elasticity values of materials 129
Table 4.5.1 – Torque level test data 141
Table 4.5.2 – Boundary condition test data 142
Table 4.6.1 – Boundary conditions used for the FE of the sensor 153
Table 4.6.2 – Summary of finite element modeling and constant-moment best test
results 161
Table 4.7.1 – Calculation of calibration factors 169
Table 4.7.2 – Calibration factors developed for correction of laboratory
acquired readings 170
Table 5.3.1 – Load Test 1 estimated strain magnitudes 190
Table 5.3.2 – Estimated strains for girder profile sensors installed at third-span of
girders 1 and 2 192
1
Chapter 1 – Introduction and Summary of Work
1.0 - Introduction
Across the United States a massive network of transportation infrastructure exists.
Starting originally with simple walking trails, this network evolved to include a web of
iron rail lines spurned by the industrial revolution and eventually concrete and asphalt
roads for the automobile. Throughout this progression the bridge has evolved to meet
these demands. From the first wooden structures spanning creeks and rivers, to
incredible displays of steel and concrete that cross gorges, bays and more, the bridge has
become increasingly complex, relying on the development of modern materials, changing
economic conditions and advanced engineering to meet project goals.
Acknowledging the importance of fostering new materials and engineering
methods, the United States Department of Transportation (DOT) created an organization
aimed at continuing the advancement of the tools available for engineers. Initiated under
the Transportation Equity Act for the 21st Century (TEA-21), the Innovative Bridge
Research and Construction Program (IBRC) is a venue for the demonstration of new and
groundbreaking material used in the construction of transportation structures (FHWA
2005). Through this program numerous materials and their applications have been
evaluated for future use in construction. The first installment of funding was allocated
for the period between 1998 and 2004 and accounted for $7 million in research and
development projects and $122 million of construction projects (Conachen 2005). The
2
program has been extended and funding currently exists for the program through the
2005 fiscal year.
Evaluation of fiber-reinforced polymer (FRP) materials has happened frequently
in the IBRC program. Although the material has been in use for a number of years, its
implementation in infrastructure has been slowed. Sources of this delay stem from
inconsistency in material properties, non-ductile failure mechanisms, and a general
unfamiliarity among designers. FRP composites are composed of oriented fibers,
typically carbon or glass, embedded in a polymeric resin and cured to form a single
material. The matrix of resin and fiber is usually drawn through a die during a process
called pultrusion, pressed into the desired shape prior to the set-up of the resin, or cured
in the final shape intended for the application. Often this process can be costly as the
machinery required may not be readily available to industry and set up of the pultrusion
process can be labor intensive. However, large-scale production can be rapid and very
little preparation is required after the curing process.
Used in lieu of steel reinforcing bars in reinforced concrete, FRP bars or multi-
directional grillages have many advantages. Leading the push in FRP implementation in
infrastructure construction is conventional steel reinforcement’s propensity to corrode. In
2002, 27.1% of the bridges in the United States were classified by the DOT as
structurally deficient or functionally obsolete (ASCE 2005). This statement groups
together structures currently open to traffic that are either not capable of operating at their
design capacities or are being subjected to demands greater than their original design
3
intended. A major cause of inadequacy for these structures is gradual deterioration of the
steel reinforcing contained within concrete decking. Penetration of water through the
concrete decking in conjunction with high concentrations of chlorides commonly found
in salts used for de-icing and snow removal facilitate this corrosion. Combating this
major source of deterioration, FRP systems are generally not affected by corrosion, and
are immune to the effects of chlorides (Jacobson 2004).
Additionally, FRP materials are capable of developing larger tensile stresses than
steel. Currently, common strengths of steel reinforcing bars reach a maximum of 75 ksi,
while glass-fiber reinforced polymers (GFRP) and carbon-fiber reinforced polymers
(CFRP) have been found to achieve maximum stresses of 230 and 535 ksi, respectively
(Dietsche 2002). These higher stress levels combined with the smaller density of FRP
relative to that of steel, may allow for less material used in design, and in turn offer cost
savings.
1.1 - The De Neveu Creek IBRC Bridge
Completed in April of 2004, the De Neveu Creek IBRC Bridge (WI B-20-148) is
a single-span bridge located on U.S. Highway 151 near Fond du Lac, Wisconsin. A
graphical representation is provided in Figure 1.1.1. The structure carries two lanes of
northbound traffic and contains generous roadside shoulders adjacent to the traffic lanes.
Part of a regional effort to reduce congestion, increase traffic flow and lower crash rates,
Highway 151 has been reconfigured, creating a bypass around Fond du Lac. The De
Neveu Creek Bridge also has a twin immediately to its geographic north, which carries
4
traffic in the opposite direction. The two bridges are nearly identical with exception
being the reinforcing material of the concrete decks. The northern bridge (WI B-20-149)
has conventional mild-steel reinforcing within its deck, while the southern bridge (WI B-
20-148, the IBRC structure) has a bi-directional FRP grillage.
The De Neveu Creek
IBRC Bridge
Figure 1.1.1 – Wisconsin Highways 151 before (left) the bypass and after (right). Adapted from
Conachen (2005).
The De Neveu Creek IBRC Bridge is of primary importance for this project. The
structure has a 130-foot span and a deck width of nearly 45 feet. The deck is eight inches
thick and supported by seven prestressed concrete stringers, which have been designed
for composite action with the deck. The stringers are set at a uniform spacing of 6’-5”
and are of Wisconsin DOT type 54W. It is of significant interest that the 54W girders
have a top flange width of 48 inches, leaving only 29 inches of unsupported deck.
5
Figure 1.1.2 – The De Neveu Creek Bridge.
The bi-directional FRP grillage in the deck was fabricated by Strongwell
Incorporated of Chatfield, Minnesota (Jacobson 2004) and was installed in two mats, on
separate levels (Figure 2.2.3). With exception to the exterior deck overhang and parapets
of the bridge, the entirety of the bridge deck is devoid of mild steel reinforcement.
The evaluation of FRP as a construction material was awarded by the IBRC as a
development, construction and long-term monitoring project at the De Neveu Creek
Bridge. The three phases of the project are as follows:
Phase I - Development of a new, cost effective material and necessary design
procedures for such material. The University of Wisconsin-Madison and
design engineers at Alfred-Benesch and Company completed this work.
Phase II – Evaluate the performance of new material for actual implementation in
the De Neveu Bridge. Full material specification was developed, as well
as quality control testing of materials for construction. The material
evaluation and quality control testing was completed at the University of
6
Wisconsin-Madison (UW). In addition, non-destructive load testing of the
bridge is required to verify design assumptions and distribution of loads
within the deck. The University of Missouri-Rolla (UM-R) conducted a
preliminary load test of both WI-B-20-148/149 in 2004, establishing load
deflection data for comparison with future load tests.
Phase III – Long term monitoring of the bridge. This monitoring is required to
provide an observation of any possible differences between the steel-
reinforced and FRP-reinforced decks exist. Additionally FRP material
properties can be more susceptible to change over time than metallic
material. Observation is thus required to verify the long-term feasibility of
specifying FRP materials in future structures.
The latter segment of Phase II and entirety of Phase III have been retained by Marquette
University and will be carried out between November 2004 and November 2009. An
additional benchmark load test of the bridge is required for long-term analysis and will be
correlated with deflection data produced by UM-R. Subsequent load testing and visual
inspections will provide the basis for long-term evaluation.
1.2 - Objective of Thesis
The objective of this thesis is to develop a cost effective, removable and reliable
strain sensor and data acquisition system to monitor the strain response of WI B-20-148
under live load testing. The portability of the strain sensor is required to limit its
exposure to the outdoor elements, as strain gages are fragile instruments. Additionally,
portability provides the opportunity to re-use the sensor in multiple locations. It is
7
intended that the sensor will be implemented in a future series of load tests. Additionally,
recommended protocol for load testing is developed for the sensor array with inclusion of
multiple deflection measurements.
1.3 - Scope of Thesis
This thesis presents the development of a strain sensor and data acquisition
system for use in an instrumentation project on the De Neveu Bridge near Fond du Lac,
Wisconsin. A fundamental-level discussion of data acquisition and usage of electrical
sensors is presented within this document as well as the design, laboratory testing and
final development of the removable strain sensors and data acquisition software. Details
pertaining to such topics are discussed herein.
Chapter 2 contains a literature review pertinent to instrumentation and bridge
monitoring, load testing efforts of similar structures and synthesis of such information.
Chapter 3 presents the details of data acquisition hardware, elementary signal processing,
an overview of electrical instrumentation and an introduction to the computer software
used in data acquisition. Chapter 4 discusses the development and calibration of strain
sensors to be used in load testing of the De Neveu Creek IBRC Bridge. Chapter 5
presents recommendations for a future load test, detailing load protocol, installation of
necessary equipment and data acquisition set-up. Finally, Chapter 6 presents
conclusions, recommendations and other observations pertinent to working with
removable strain sensors.
8
Chapter 2 –Literature Review and Synthesis
2.0 - Introduction
A wide variety of information exists on the multitude of methods for which
diagnostic information can be obtained from structures. The vast amount of equipment is
commercially available and can be daunting to sift through. The selected instrumentation
efforts presented below document the results of a variety of data acquisition systems
operating in differing environments and configurations.
Organization of this chapter begins with general recommendations for the
diagnostic information collection of bridge structures followed by an introduction of the
bridge to be studied in this project. The design, configuration and construction of the De
Neveu Creek IBRC Bridge are documented as well as an overview of preliminary
attempts to obtain benchmark values of strain and deflection data. Four additional load
test projects are also documented, each outlining the data acquisition methods employed
and results of each load test conducted. Finally, a synthesis of the literature documented
in this section is provided, detaining the rationale for development of the strain sensor to
be used in instrumentation and monitoring of the De Neveu Creek IBRC Bridge.
2.1 – Instrumentation Guidelines
As state or federal governments own a majority of bridge structures in the United
States, a number of government agencies have produced documents recommending
procedures for their instrumentation and monitoring. As of recent times, the Federal
9
Highway Administration (FHWA) produced guidelines for the instrumentation of
bridges, specifically those utilizing high performance concretes in their construction
(FHWA 1996). Similarly, the National Cooperative Highway Research Program
(NCHRP) has developed research initiatives aimed at identifying guidelines for load
testing when rating bridges (NCHRP 1998). Conforming to these guidelines, academia
frequently carries out the load testing of structures. Farhey (2005) provides an excellent
summary documenting the need for diagnostic bridge testing and recommendations for
the instrumentation of structures.
The FHWA publication was created in response to the ever-expanding use of high
performance concretes in practice and the corresponding lack of pertinent research on the
material. The document notes that there are a number of methods available for the
instrumentation of structures; however, this discussion is limited to short-term monitoring
only. For clarity, short-term monitoring is focused on testing that imposes loads on a
structure over a period of a few hours. Specifically, both static and dynamic live load
testing can be considered short-term monitoring. Furthermore, long-term loading
involves monitoring a structure over a significantly longer period, typically months or
years. Long-term monitoring typically focuses on effects due to shrinkage of concrete,
creep of a structure, effects due to cyclic changes in temperature and other time-
dependent effects.
Both the FHWA and NCHRP recommend that short-term strain acquisition be
performed by electrical resistance type gages. Vibrating-wire type gages are not capable
10
of rapid acquisition but are best suited for long-term monitoring of strains. As in-field
attachment can be difficult, gages to be embedded in concrete should be installed to full-
size sections prior to placement if at all possible. Full-size, instrumented sections of
reinforcement can then be placed in simultaneously with the reinforcement specified
during construction, eliminating the difficulties of field installation. The document also
notes that gages should be adequately protected from both the placement of concrete and
the fresh concrete itself. As each manufacturer produces strain gages of differing
specifications, protection should adhere to the manufacturer’s recommendations.
Furthermore, the FHWA acknowledges that gages can be mounted to exterior surfaces of
hardened concrete. Although more difficult to perform successfully, gages can be
bonded to smooth surfaces, which typically provide an adequate substrate. Troweled,
broom finish and other rough finished surfaces can be more difficult to install gages and
require surface preparation, but have been performed successfully in the past.
Temperature fluctuations are also of importance when obtaining measurements.
Typically electrical resistance strain gages are available with a temperature-compensated
backing to match the intended substrate being monitored. While this backing eliminates
much of the potential thermal effect, no two materials have exactly the same coefficient
of thermal expansion allowing for the possibility of thermal differences between them.
Compensation for these differences is prudent and should be employed for both
measuring instruments and also for any changes in the substrate itself (NCHRP 1998). A
simple solution recommended to address temperature changes is to conduct testing near
sunrise as temperature gradients are at a minimum (FHWA 1996).
11
Finally, instruments used in any monitoring project require that an appropriate
level of resolution be available. In short-term monitoring values of strain smaller than
100µε are common (FHWA 1996). Usage of high impedance strain gages, typically 350
or 1000 ohms, improves the signal-to-noise ratio of measurements (NCHRP 1998).
Resolution of instruments also requires analysis of region of the substrate to be sampled.
When monitoring a heterogeneous substrate, e.g. reinforced or prestressed concrete, large
gage lengths are required to eliminate local effects (Farhey 2005). Although use of a
larger gage length averages measurements over a region, it also limits local effects that
may omit valuable readings.
At the time of publication a single, reliable method of measuring displacement
was felt to be non-existent for bridge girders (FHWA 1996). However, the use of
calibrated surveying equipment or taut-wire measurement has proven to be successful in
practice. Taut-wire measurements require the installation of a wire, stretched between
two known points of reference with a known tensioning force. Measuring the movement
of girder relative to the wire can produce displacement values. However, utilization of
precise surveying equipment may offer greater flexibility when site conditions limit
physical contact-type measurement of displacements on a bridge. Placement of optical
sensors, prisms, or other similar surveying equipment on the structure allow for it to be
observed from a distance using a calibrated surveying station. Displacements can also be
measured with electrical transducers, e.g. potentiometers, linear variable differential
transformers (LVDT’s) or dial gages but require a stable mounting location. These
12
methods are typically not practical for displacement monitoring of long-span girders and
best suited for local measurements.
Specific product recommendations are made by the FHWA (1996). The following
instruments are recommended for use in the instrumentation of structures and monitoring
of bridge superstructures and substructures.
Short-term monitoring:
Internal adhered gages on steel reinforcement -
• Micro Measurements CEA-06-250-UW-350 or CEA-06-250-UW-120
• Micro Measurements CEA-06-250-AE-350
External adhered gages on hardened concrete -
• Micro Measurements EA-05-20CBW-120 or EA-06-20CBW-120
• Micro Measurements EA-05-40CBY-120 or EA-06-40CBY-120
External weldable gages on structural steel -
• Texas Measurements TML AWC-8B
Long-Term Monitoring:
Vibrating Wire Gages –
• Geokon VCE-4200 or VCE-4210
• Roctest EM-5
It should be noted that a substantial body of knowledge regarding bridge
monitoring and instrumentation exists in the form of various journal articles, research
papers and other engineering publications. In fact, a substantial portion of mechanical
13
measurement curricula may be applied to diagnostic bridge monitoring in the form of
displacement and strain measurement. The documents presented in this section are
intended to illustrate that significant efforts focusing on structural bridge monitoring have
previously been performed by a number of agencies and organizations, and those
reviewed are most pertinent to the current effort.
2.2 – The De Neveu Creek IBRC Bridge
As part of the ongoing effort to further develop a new suite of construction
materials available to the engineer, extensive research and development has been
conducted in the state of Wisconsin under the guise of the IBRC program. Details of the
IBRC program can be found section 1.1, which introduces the design and construction of
the De Neveu Creek Bridge near Fond du Lac, Wisconsin.
Conventional in appearance, the De Neveu Creek IBRC Bridge (WI B-20-148) is
located on U.S. Highway 151 south of Fond du Lac, Wisconsin and is part of a new
bypass system. A photograph of the structure can be found in Figure 2.2.1. A partial
plan set of the De Neveu Creek Bridge, as well as its southbound counterpart (B-20-149),
may be found in Appendix A. The bridge is a single-span structure approximately 130’
long and carries two northbound lanes of highway traffic. The structure is skewed
approximately 25 degrees and contains minimal superelevation (0.056 feet/foot). Seven
prestressed concrete stringers, or girders, support the 8” thick FRP-grillage reinforced
concrete deck and are intended to act compositely with the FRP-reinforced deck. Shear
transfer is provided by epoxy-coated #4 mild steel reinforcing bars protruding
14
approximately 6” from the top flange of each girder and extending transversely 1’-0”,
parallel to the plane of the deck. These shear transfer bars are placed in duplicate, but
opposite transverse directions and longitudinally 1’-6” on center. Stringers are of
WisDOT type 54W and spaced transversely 6’-5” on centers. The 54W girders present
an interesting condition when supporting the deck as the top flange of the stringer is 4’-0”
wide. This large top flange dimension leaves an unsupported deck span of only 2’-5.”
Figure 2.2.2 provides a cross section of the bridge and illustrates this narrow spacing of
the stringers. Also, the concrete specified in the construction of the prestressed stringers
was to be of 9,600 psi minimum compressive strength, which can be considered high
strength concrete (Mindess et al. 2003). The 28-day compressive strength of the deck
concrete was specified as 4,000 psi. Finally, conventional mild-steel reinforcing bars are
used only on the exterior overhangs of the deck and integral parapet guardrails, as
federally approved FRP-reinforced parapets were not available during the design phase
(Jacobson 2004).
Figure 2.2.1 – The De Neveu Creek Bridge, WI B-20-148.
15
Figure 2.2.2 – Cross section of the De Neveu Creek Bridge.
2.2.1 - FRP Reinforcement in the De Neveu Bridge
The FRP grillage reinforcement merits a detailed description. Initiated as part of
an IBRC directed project through the University of Wisconsin-Madison and Alfred
Benesch & Company, a system of pultruded FRP-reinforced concrete was developed for
implementation at multiple bridge locations. Jacobsen (2004) notes that design of the
FRP-reinforced slab conforms to the recommendations of ACI-440, the State-of-the-art
Report on Fiber Reinforced Plastic Reinforcement for Concrete Structures. The FRP
reinforcement is a bi-directional grating system consisting of two individual layers of
reinforcement, with one layer placed directly over the other layer. Figure 2.2.3 illustrates
the double-mat FRP grillage.
Figure 2.2.3 – Assembled FRP grillage (Conachen 2005)
16
Each grating layer contains two separate types of pultruded FRP elements. The primary
reinforcing member is a 1.5” high “I” bar spaced at 4” on centers and is positioned in the
transverse direction of the deck, perpendicular to the traffic lane. Running orthogonal to
the I-bars, or parallel to the direction of traffic, are cross-rods spaced at 4” on centers.
Each cross-rod is constructed of three independently pultruded elements, which
are assembled in the manufacturing facility. Figure 2.2.4 illustrates the grillage
components. The center cross-rod section is first notched for the I-bars by a CNC
machine and then threaded into the I-bars. The top and bottom “wedge” pieces are then
pressed onto the center cross-rod and adhered with resin. The wedge pieces lock the I-
bars and cross-rods into a 4” by 4” grillage. A second layer is then affixed to the
previous with shear connectors creating a double-mat grillage (Conachen 2005). The
shear connectors create a constant 2.5” separation between grillage mats and are
positioned 36” transversely (along the I-bars) and 24” longitudinally (Jacobson 2004).
Material properties for the pultruded FRP-grating may be found in Table 2.2.1.
Figure 2.2.4 – Cross sections of FRP materials used (Conachen 2005).
17
Table 2.2.1 –FRP-grillage material properties (Dietsche 2002).
2.2.2 - Development and Testing of the FRP-grillage Reinforced Deck
Extensive evaluative testing of the FRP-grillage reinforcement for implementation
in reinforced concrete was conducted. Early experiments with commercially available
FRP materials included the testing of concrete slabs reinforced with various “T-bar”
grillages that resulted in rapid shear failure of the systems (Bank et al. 1992a; Bank et al.
1992b). A number of two-span, FRP-reinforced slabs were constructed with double mats
of grillages, subjected to design loads and ultimately tested to failure. Additionally, a
conventionally mild-steel-reinforced slab was built as a comparison specimen. Both
spans of the test were 8’, intending to mimic spans between bridge girders. Test results
indicated that the FRP-grillage systems consistently experienced ultimate failure at loads
18
greater than that of conventionally reinforced systems. However deflections observed in
the FRP-reinforced systems were greater than their conventional counterpart. While
greater loads were carried, the rapid shear failure of the FRP-reinforced slabs warranted
concern as little warning was observed prior to failure. A follow-up study utilizing
similar materials with shorter span lengths was also conducted further investigating the
shear failure of FRP-reinforced slabs (Bank and Xi 1995). It was identified that the FRP-
reinforced slabs behave very similar to conventionally reinforced concrete up until their
rapid punching shear failure.
Jacobson (2004) performed significant additional testing specific to this bridge
project utilizing similar geometric configurations and materials found in the De Neveu
Creek IBRC Bridge. As expected, the research carried out indicated that punching shear
is the expected strength limit state for the FRP-reinforced deck. Like the tests of Bank, et
al (1992, 1995) this limit state was observed at load levels that were many times greater
than the design load. For clarity, FRP-reinforced slab was designed to accommodate an
AASHTO HS-20 truck (Jacobson 2004). Overall, it was found that when using geometry
representative of the De Neveu Creek IBRC Bridge, the strength requirements would be
satisfied with a factor of safety greater than ten.
Serviceability requirements were also studied in depth, providing deflection
response of the system. Warranted by the greater deflections observed in early testing
(Bank et al. 1992a), two separate types of load tests were conducted during
experimentation by Jacobsen (2004). A series of simply supported slabs were
19
constructed, each spanning 6’-6” and loaded with a 16-kip “wheel load” representing the
HS-20 design vehicle. Two additional slabs were constructed with end restraints more
closely representing the true behavior of the bridge. These slabs also had a clear span of
6’-6”, however, rotational restraint was provided beyond the end of each support.
Figures 2.2.5 and 2.2.6 illustrate the test configurations. Overall, satisfactory span-to-
deflection ratios were consistently observed with deflection ratios greater than L/1330 for
simple spans and L/7200 for restrained slabs.
Figure 2.2.5 – Simple-span slab tests (Jacobson 2004).
Figure 2.2.6 – Restrained end slab tests (Jacobson 2004).
It is important to note that although performance of the slabs in the laboratory indicated a
satisfactory response, the support conditions of each slab tested as well as the overall
20
span lengths did not accurately represent the actual configuration of FRP-reinforced slabs
in the De Neveu Creek Bridge.
2.3 - Load Testing of the De Neveu Creek Bridge
Documentation of load testing for the De Neveu Creek Bridge can be found in the
work of Conachen (2005). To identify benchmark values of strain and deflection for the
in-situ structure, the University of Missouri-Rolla was contracted to perform a load test.
The test would involve both bridges at the site (B-20-148 and 149) to provide
comparative data for the FRP-reinforced and traditionally reinforced structures. A
robotic total station was employed to capture deflection data with surveying prisms. The
prisms were located primarily at the mid-span of each bridge with reference prisms
placed at quarter points. Figure 2.3.1 indicates the locations of each surveying prism.
Note that on the De Neveu Creek Bridge (B-20-148) a prism was located on both the east
and west abutments while another was located on the west abutment of B-20-149. These
prisms mounted to the abutments were assumed to remain static during testing and
provided stable reference points for the robotic total station to make its readings.
21
Figure 2.3.1 – Layout of surveying prisms and strain gages. Adapted from Conachen (2005).
2.3.1 - Strain Gage Instrumentation of the Bridge
A modest array of gages was installed at various locations within both bridges.
Gages were installed directly on the FRP grillage and embedded in the concrete, while
others were applied directly on the surface of the deck. The gages installed on the FRP
were placed in two sub-arrays, each consisting of paired gages in various locations. One
sub-array was located directly over girder number 6 (second girder from the south of B-
20-148) and did not include the lower mat of the FRP grillage. Intent of these gages was
to measure strain caused by negative moment in the deck over the stringer. Surface
mount gages were also provided at this location to produce outer surface strain data in an
attempt to identify the strain profile through the thickness of the deck. These gages were
paired and located longitudinally in three installments. No indication of the longitudinal
spacing can be found in Conachen’s work, however. Illustrations depicting the locations
22
of strain gages installed on the De Neveu Creek Bridge can be found in Figures 2.3.2 and
2.3.3.
Figure 2.3.2 – Strain gage locations. Adapted from Conachen (2005).
Figure 2.3.3 – Strain gage locations. Adapted from Conachen (2005).
The other sub-array was installed on both FRP-grillages at mid-span between the
number 6 and 7 stringers. Intent of these gages was to obtain strain data relating to
positive moment between girders. As with the negative moment gages, surface mount
gages were installed on both top and underside of the FRP-reinforced concrete deck. The
number of gages installed was not clear, however, it is understood that at least six gages
23
were installed in three pairs, similar to the layout as the gages over girder number 6.
Again, the longitudinal spacing of the strain gages installed was not provided. .
All gages embedded in concrete were protected, as the instruments are highly
sensitive and placement conditions of fresh concrete near strain gages is an unfriendly
environment. The author notes that a “fast-drying silicone” was used to protect the
gages, contrary to commonly recommended and typically performed methods. Lead
wires for the gages were placed in plastic tubing and terminated in a junction box on the
underside of the deck.
Product numbers for the instruments were as follows:
• Embedded Gages – Micro Measurements CEA-06-250UN-350 (350 ohm,
0.25” gage length)
• Surface Gages – Tokyo Sokki Kenkyujo PL-60-11 (120 ohm, 2.362” gage
length)
2.3.2 - In-Situ Load Test of B-20-148 FRP Bridge
The load testing of the De Neveu Creek Bridge was conducted with a total of six
WisDOT provided dump trucks. Each truck was a three-axle vehicle with total weight of
approximately 75,000 lbs. Four load tests, or “stops,” were conducted in the following
arrangements (Figure 2.3.4):
• Test 1 – A three-truck “train” located along both girders 2 and 6 with a
wheel load directly over girders 2 and 6. Six total trucks.
24
• Test 2 – A three-trucks “train” located along both girders 3 and 5 with a
wheel load midway between deck spans. Spans directly loaded were
between girders 2 and 3 and between girders 5 and 6. Six total trucks.
• Test 3 – A single four-truck “train” located along girder 6 with wheel
loads midway between girders 6 and 7.
• Test 4 – A single four-truck “train” located along girder 6 with wheel
loads midway between girders 1 and 2.
In each test the trucks were positioned appropriately and stopped for a minimum
of 10 minutes to allows for settling (Bank 2005). Deflection data were obtained in
duplicate for all sensors and then the trucks were removed. It is important to note that
significant strain data was not recorded for the De Neveu Creek Bridge as the strain
equipment was not operating properly during testing (Bank 2005).
25
Figure 2.3.4 – Stopped vehicle locations for live-load testing of B-20-148 FRP (Bank 2005).
26
2.3.3 - In-Situ Load Test of B-20-149 Conventional Bridge
The load testing of B-20-149 was conducted with the same six WisDOT dump
trucks provided for testing of the De Neveu Creek Bridge. Three load tests, or “stops,”
were conducted in the following arrangements (Figure 2.3.5):
• Test 1 – A single four-truck “train” was located along girder 8, centered
laterally over the girder.
• Test 2 – Three-truck “trains” were located along both girders 3 and 8 with
a wheel load directly over girders 3 and 8. Six total trucks.
• Test 3 – A single four-truck “train” was located along girder 4, centered
laterally over the girder.
27
Figure 2.3.5 – Stopped vehicle locations for live-load testing of B-20-149 Conventional (Bank 2005).
2.3.4 - Results of B-148 and B-149 Load Tests
Maximum deflection of the De Neveu Creek Bridge (B-20-148) occurred in
girder 4 of Load Test 2 and was approximately 0.67” downward. A plot of deflection
data can be found in Figure 2.3.6. Maximum strain read from the gages occurred during
28
load test 3 was + 42 µε in the bottom FRP-grillage between girders. It should be noted
that all strain data recorded in the testing of the De Neveu Creek Bridge is in question as
a number of gages failed during testing. Maximum deflection values listed in Table 2.3.1
were approximated from the graphs presented for each load test.
Figure 2.3.6 – Deflection plot of mid-span girder response in bridge B-20-148 FRP. Adapted from
Conachen (2005).
Load Test Girder ∆ (mm) ∆ (in)
1 4 -14.5 -0.57
2 4 -17.5 -0.69
3 1 -11 -0.43
4 7 -12 -0.47
Maximum Mid-span Displacement
Table 2.3.1 – Maximum mid-span displacement data from live load tests in bridge B-20-148 FRP.
Adapted from Conachen (2005).
29
Maximum deflection of the conventionally constructed bridge (B-20-149)
occurred in girder 4 of Load Test 2 and was approximately 0.47” downward. This is
expected as the conventional bridge has two additional girders that provide additional
stiffness to the structure. A plot of deflection data can be found in Figure 2.3.7. Table
2.3.2 contains a summary of maximum mid-span deflections during testing.
Figure 2.3.7 – Deflection plot of mid-span girder response in bridge B-20-149 Conventional. Adapted
from Conachen (2005).
Load Test Girder ∆ (mm) ∆ (in)
1 7, 8, 9 -9.5 -0.37
2 7 -12 -0.47
3 3, 4 -8 -0.31
Maximum Mid-span Displacement
Table 2.3.2 – Maximum deflection data from live load tests in bridge B-20-149 Conventional.
Adapted from Conachen (2005).
30
Overall, the deflection data for both structures provides insight into the
distribution of load between girders. In load cases designed to utilize both lanes of the
bridge (load cases 1 and 2 for the De Neveu Creek Bridge) multiple girders were
activated to resist the loads. Additionally, when attempting to localize loads to a specific
girder (load cases 3 and 4 for the De Neveu Creek Bridge), girders adjacent to the loads
were also activated to distribute them accordingly. Distribution factors for each girder
were computed using the expression, ii
TOTAL
DFδ
δ=∑
where δi indicates deflection of
the i-th girder. A listing of approximate girder distribution factors (GDF) can be found in
Table 2.3.3. Based upon these results, the AASHTO girder distribution factors
(AASHTO Section 4.6.2.6) were observed to be conservative as the prescribed formulas
neglect outside factors that can provide additional stiffness to the structure (AASHTO
1996; Bank 2005). Also, it was acknowledged that the strain data collected is not of any
significant use (Bank 2005).
Girder 1 2 3 4
1 0.11 0.10 0.03 0.22
2 0.13 0.12 0.07 0.22
3 0.16 0.17 0.11 0.20
4 0.17 0.19 0.16 0.16
5 0.16 0.17 0.20 0.10
6 0.13 0.12 0.21 0.07
7 0.11 0.10 0.20 0.03
Interior Girder
Exterior Girder
0.54
0.49
0.38
0.45
Approximate GDF from Load Tests
Load Test
2 Lane Loading 1 Lane Loading
AASHTO GDF
Table 2.3.3 – Approximate girder distribution factors for load testing of B-20-148 FRP (AASHTO
1998; Bank 2005).
31
2.4 – Ohio Bridge HAM-126-0881 (Lenett et al. 2001)
The structure under consideration for this investigation was a three-span steel
girder bridge with a conventionally reinforced concrete deck. Construction of the bridge
started in 1995 and it was commissioned in 1997. With a goal being to produce a
complete scientific view of the loads typical bridge structures endure over the course of
their service lives, the researchers monitored loads and displacements present in the
bridge for nearly all aspects of the project. Data was recorded during fabrication of the
steel stringers, during transportation to the jobsite and through erection. Long-term
strains and temperature data are still being monitored today through a permanent data
acquisition system. The effort put forth by the researchers for this investigation and
subsequent evaluation was exhaustive and included a multitude of topics related to
conventionally constructed steel stringer bridge structures. For this reason, only aspects
of the project’s instrument evaluation and selection and live load testing were reviewed.
As noted previously, the structure considered for this project was a two-lane, three-span
bridge with a reinforced concrete deck supported by steel wide-flange girders. Figure
2.4.1 illustrates the bridge studied. All components of the bridge were constructed by
conventional means and did not utilize any experimental materials or construction
methods. Five steel stringers support the mild steel reinforced concrete deck that rests on
two intermediate piers and terminate atop the abutments. Exterior spans are
approximately 40’ while the center span is approximately 88’. The length of each span is
noteworthy as the exterior–to-center ratio is only 0.45. The authors make note that the
Ohio Department of Transportation recommend a exterior-to-center ratio more near 0.8 to
32
equalize the positive bending moments of each span. The exterior stringers were
W36x194 shapes while the center span girders are W36x182 shapes. Spliced connections
are utilized approximately 15’ from each pier in the center span. Additionally, only the
center span stringers are designed for composite action with the deck. This is achieved
by using 1” diameter x 5” tall steel studs spaced along the length of the stringer. No
provisions were made outside of the center span to employ composite action.
40.2’ 88.5’ 40.3’
43’
West Pier
West AbutmentEast Pier
East Abutment
N
4 @ 9’-9”
Figure 2.4.1 – Schematic of Ohio Bridge HAM-126-0881.
2.4.1 - Data Acquisition System Employed
The researchers conducted an extensive evaluation of commercially available
instrumentation equipment citing a number of conclusions. Vibrating wire strain gages
are most suitable for use in long-term monitoring projects. Additionally, integral
temperature sensors are available with this type of gage. Vibrating wire strain gages can
be used for short-term live load testing, however acquisition time of the gages is
significant and requires long vehicle stoppage and settling periods. Electrical resistance
gages are of excellent use for short-term, high speed testing, however, use for long-term
testing is not recommended due to their propensity to lose their datum or drift from their
initial reading.
33
Reliable data collection is possible from a number of acquisition systems available
commercially. However no system is best suited for all projects. The two systems used
for this project are outlined below:
o The slow-testing devices were read using a rugged and readily mobile
system produced by Campbell Scientific. The CR-10 model could run
continuously on 12-volt battery DC power. The unit could scan only one
channel at a time and obtains data at 64 Hz.
o The high-speed devices were read using a MEGADAC system produced
by Optimum Electronics. The system utilized a high-speed interface (up
to 25 kHz) between the analog-to-digital converter and a computer. This
allowed for ample sampling of data during higher speed testing. Due to
continuous electrical requirements, its susceptibility to damage by
weather, and its high cost, use of this system was limited to the high-speed
devices and installed in a permanent structure located near the bridge.
Displacement transducers used for the project were Celesco PT101-SWP string
potentiometers and Trans-Tek 244 DC-LVDT linearly variable differential transformers.
Electrical resistance gages selected for the high-speed data acquisition varied
according to their installation locations. Gages to be mounted on the steel stringers were
of weldable and manufactured by Texas Electronics, product AWC-8B. Installation
requires spot welding of the stainless steel enclosure directly to the steel substrate. Strain
gages of this type were also located on the transverse diaphragms, or cross-frames, of the
34
bridge in multiple locations. Gages to be installed in the concrete deck were of
embedded type and cast directly into specified location in the concrete. Special care was
taken during casting of the deck to ensure correct location of each sensor. The embedded
sensors were Micro Measurements EGP series gages. Acknowledging that this project
included near-continuous monitoring of over 600 independent channels of data, the
recommendations conveyed within the documentation are held in high-regard.
2.4.2 - Load Testing and Results
Two live load tests were conducted. Vehicles specified for testing were two
three-axle dump trucks, of which the independent loads were documented at the time of
testing. It was acknowledged that the weight of each truck pair varied from the
benchmark to in-service tests and properly recognized in all following results.
The first test was a static, post-construction test to benchmark the load and
displacement data of the structure prior to traffic loading. Eleven different load cases
were conducted at varying locations to profile the strain response of the structure.
Location of test vehicles is illustrated in figure 2.4.2. Each load case consisted of
locating the test vehicles at points of interest along the spans. The trucks were always
positioned adjacent to each other, or longitudinally in a tailgate-to-tailgate fashion.
35
Figure 2.4.2 – Static live-load Cases A through L (Lenett et al. 2001)
A follow-up load test was conducted once the structure had been in service for
over one year. Similar truck positions were utilized as the benchmark test; however, the
in-service condition prohibited locating trucks adjacent to each other. In order to conduct
each load case, control measures were installed to limit traffic to only a single lane of the
36
bridge. To obtain data for each load case, the test vehicle was positioned in the closed
lane next to the open traffic lane. When ready, temporary traffic stops were imposed to
eliminate transient loading from passing vehicles and data collected. As only a single
lane of the bridge was loaded with a test vehicle, as opposed to the twin loading of the
benchmark test, corresponding results were then superimposed for comparison.
Results from the two sets of load tests yielded the following conclusions. The
intermediate cross-frames contributed to the internal redundancy of the structure and
spread the distribution of loads laterally throughout the structure. These frames were
located at 14’ intervals between all stringers and contained weldable strain gages that
were active during all load tests. Composite action of the stringers and deck exists
throughout the center span, which was intended for in design. Partial composite action
was observed in exterior spans during the benchmark load test. This partial composite
behavior, although common in structures of this type, was not intended. However, after
completion of the second load test, the eastern exterior span had lost all indication of
partial composite action while the western exterior span had decreased its degree of this
behavior.
Load distribution factors for each stringer on the structure were calculated based
on the results of each load test. The authors present a method by which the internal
moment of each stringer can be calculated. Load distribution factors were then computed
using:
GirderGirder
AllGirders
MDF
M=
∑ (2.4.1)
37
The method used to develop internal moments within each girder is as follows:
Figure 2.4.3 – Method for calculating internal moments in stingers (Lenett et al. 2001)
2.5 – South Carolina Route S655 (Turner 2003)
The new Route S655 Bridge over the Norfolk/Southern rail line near Landrum,
South Carolina, replaced an antiquated steel and timber deck structure. The previous
two-lane structure had been in service as early as 1946 and was not in sufficient condition
to safely carry two lanes of modern traffic. Completed in 2001, the new structure spans
60 feet with five steel stringers and a unique glass-fiber reinforced polymer (GFRP) deck.
The W36x150 stringers are located with an 8’-0”center-to-center spacing, which, as
38
indicated by the author is intended to challenge the limits of the GFRP deck. Also, to
better understand the behavior of the GFRP system, the bridge was instrumented and load
tested. The structure is currently under traffic.
2.5.1 - GFRP Deck Panels
The commercially available deck panels are composed entirely of built up
sections, each consisting of approximately ten pultruded elements. The Duraspan®
panels were produced by Martin Marietta Composites
(www.martinmarietta.com/Products/ composites.asp) and have a number of successful
installations around the country. Each element is 37.2’ wide (corresponding to the bridge
deck width), 7.6” deep and 12” long and is connected to adjacent elements with an
adhesive resin. Pre-assembled panels of these elements were delivered to the site and
installed longitudinally atop each stringer. Each pre-assembled panel was the full width
of the bridge deck and 10’ long. Significant fieldwork was required to install each
section as each individual panel required adhesion to adjacent panels and hand laid FRP
splice panels to prevent moisture penetration. Additionally, each deck panel is designed
to act compositely with the steel stringers and thus significant investigation of the
connection’s shear transfer performance is documented. An illustration of the deck panel
and the installed configuration can be found in Figures 2.5.1 and 2.5.2.
39
Figure 2.5.1 – Individual Duraspan® deck panels. Adapted from Turner (2003).
Figure 2.5.2 – Section of bridge deck and integral grout-filled shear pockets (Turner 2003)
Shear transfer for composite action of the GFRP deck and steel stringers was
achieved using three 7/8” diameter by 3” tall steel studs encased in a high-strength grout
pocket. The studs were placed along stringer lines and spaced at 2’-0” on centers. To
verify the actual composite response of the deck and stringers, both full-scale load tests
40
and laboratory testing were by Turner (2003). While the experimental design of the
structure incorporated composite behavior the stringers were designed to support the
bridge in a non-composite manner. This over-designing of the bridge allowed for an
acceptable level of safety in the event that the steel studs did not behave as intended.
2.5.2 - Instrumentation and Load Testing
A variety of instruments were installed on the bridge for the data acquisition
during load tests. Duplicate electrical resistance strain gages were installed at eighth
points along the span. Weldable gages were installed on the steel girders and oriented
longitudinally to obtain strain distribution through the depth of the stringers.
Complementing the weldable gages, adhesive-applied gages were installed on the GFRP
deck in both longitudinal and transverse directions. The transverse gages on the deck
were intended to provide strain data relating to the behavior of the deck in resisting wheel
loads. Longitudinal gages were intended to produce strain data that would relay
information pertinent to the degree of composite behavior of the deck and stringers. In
addition to the strain gages, draw wire transducers (DWT) were installed to measure
vertical deflection of the deck relative to the top of the stringers. Finally, surveying
prisms were installed at locations along the lower flange of the stringers to monitor the
deflection. Figure 2.5.3 illustrates the layout of instruments.
41
Figure 2.5.3 – Instrument layout of S655 Bridge (Turner 2003)
The load test protocol was repeated in two different test sessions and utilized
three-axle dump trucks classified between an AASHTO HS23-44 and HS25-44 load.
Five load cases were conducted and are illustrated in Figure 2.5.4. The goals for Load
Combination 1 and 2 were to determine behavior in both instrumented and un-
instrumented areas of the structure. Load Combination 3 was used to determine behavior
of the panels under two-lane loading while Load Combination 4 aimed at observing the
response of the GFRP deck over an interior stringer (negative bending behavior).
Finally, Load Combination 5 was used to determine positive moment response of the
GFRP deck between stringers (positive bending behavior).
42
Figure 2.5.4 – Live-load test cases for S655 Bridge (Turner 2003)
To perform the test for each load case the specified truck(s) were driven to
instrumentation points and stopped for data acquisition. Furthermore, each individual
load case was performed twice.
The magnitudes of strain recorded were reasonably consistent between the two
days of testing and of reasonable magnitude. A summary of maximum deflection and
strain values for both load tests is given in Tables 2.5.1 and 2.5.2.
43
1 2 3 4 5
Max Girder ∆ (in) -0.144 -0.156 -0.288 -0.156 -0.156
Max Girder uStrain 40 33 78 42 42
Max Deck ∆ (in) -0.019 +0.006 -0.013 -0.017 -0.020
Max Deck uStrain 60 10 95 64 106
Load Case
Load Test #1
Table 2.5.1 – Load Test #1 - Maximum load test values.
1 2 3 4 5
Max Girder ∆ (in) -0.120 -0.108 -0.216 -0.120 -0.132
Max Girder uStrain 40 34 72 40 52
Max Deck ∆ (in) -0.019 +0.006 -0.015 -0.020 -0.018
Max Deck uStrain 72 12 90 100 82
Load Test #2
Load Case
Table 2.5.2 – Load Test #2 - Maximum load test values.
Strain distribution through the depth of the cross-section was analyzed to evaluate
the degree of composite action between girders and GFRP decking. It was noted that the
magnitude of many of the values recorded in these load tests were equal to or smaller
than the accuracy of the data acquisition system (Turner 2003). Thus strain distribution
data from Load Case 3 was used to draw conclusions as the magnitude of its strain data
was generally much higher than the other four load cases. Based on Load Case 3 it was
concluded that partial composite action was present between the girders and deck. This
conclusion was also consistent with behavior observed in laboratory testing of steel stud
specimens. During the laboratory testing, the equivalent shear loads found in a
composite system were not attained by the deck material. Specifically, it was observed
44
that the decking material continually failed in localized regions before the expected
strength of the grout pocket could be achieved.
Moment distribution factors of the steel stringers were also studied and compared to
design procedures found in the 1996 AASHTO Standard Specification and the 1998
AASHTO LRFD Manual. Experimental distribution factors calculated from strain data
used the following equation:
g
jj
all irders
strainDF
strain=
∑ (2.5.1)
Reviewing the results it was found that the experimental distribution factors were
consistent with the AASHTO predicted values.
2.6 – Fairground Road Bridge
The bridge studied in this document was a three-span, two-lane structure spanning
the Little Miami River in Greene County, Ohio (Bridge Diagnostics Inc. 2002). The
tested structure is composed of FRP deck panels installed on existing steel stringers.
Martin Marietta Composites (www.martinmarietta.com/Products/composites.asp)
manufactured each hollow core FRP panel and is the same product studied by Turner
(2003) in the South Carolina S655 Bridge. Similarly, composite action is achieved by
using three, 7/8” diameter x 3” tall steel studs in a cellular pocket filled with high
strength grout. The pockets are also located at 2’-0” on-centers along the length of each
stringer. The focus of investigation for this project was primarily the analysis of
composite behavior between the FRP deck panels and steel stringers and, while not
pertinent to this project, the load rating of the structure.
45
2.6.1 - Study of Composite Action and Strain Measurements
To study the composite behavior of the deck system and stringers, strain transducers
manufactured by Bridge Diagnostics Incorporated (www.bridgetest.com/index.htm) were
installed on the stringers of the structure with a small number of transducers installed
directly on the FRP deck panels for verification of results. Four locations along the
length of the bridge were selected as instrumentation points:
• 4’-0” from abutment
• Mid-span of outer, shorter span
• 4’-0” from support pier
• Mid-span of center, long span
These locations provide the opportunity of symmetry to study the structure, saving cost of
installation on the entire bridge. A top and bottom flange longitudinal transducer was
installed on each of the stringers at instrumentation points for a total of 32 units (Figure
2.6.1). For verification of strain distribution through the section of the bridge, two
additional longitudinal transducers were installed on the FRP deck near the top flange of
an interior stringer at mid-span of the outer span. Also, two transducers were installed
transversely on the FRP deck between stringers to monitor the bending behavior of the
FPR deck itself. To monitor vertical displacement of the FRP deck, four linearly varying
differential transformers (LVDT) were installed atop the pier as well.
46
Figure 2.6.1 – Instrumentation layout of the Fairground Road Bridge
A driving factor in the decision to use strain transducers in lieu of adhered foil
gages is the possibility of removal between test sessions. Also, the speed at which the
equipment can be installed or removed is rapid. Removal of the equipment limits the
possibility of vandalism and degradation due to weather. A photograph of the strain
transducer may be found in Figure 2.6.2.
Figure 2.6.2 – Bridge Diagnostics Strain Transducer (BDI 2005).
2.6.2 - Load Testing and Results
The load test consisted of slowly (less than 5 mph) driving a three-axle dump
truck across the structure in a series of four prescribed paths. The authors did not
47
disclose detail of load location but did note that duplicate runs were performed to check
consistency of data. Stationary, static load testing of the structure was not performed.
While truck passes were being made, continuous monitoring of the sensors occurred.
Relative distance of the vehicle along the bridge was also monitored. It is of note that
data acquisition of the live load test was sampled at a rate of 40 Hz. A final high-speed
test was also conducted with the test vehicle moving at approximately 45 miles-per-hour
to estimate the impact effect of design vehicles.
The data collected produced a number of interesting results. Using the
assumption that elastic response is observed in the structure, the authors calculated the
neutral axis of each stringer based on the strain readings recorded. Figure 2.6.2 illustrates
the method used for neutral axis computation. The following equation was used to locate
this axis relative to the bottom flange of each stringer:
( )
bottomna
top bottom
dy
εε ε
•=
− (2.6.1)
The distance between reading surfaces of the transducers is noted as “d” in the
above expression (Figure 2.6.2). Based upon these calculations the neutral axis of each
stringer was found to be consistent with others in the structure and also indicated some
degree of composite nature. That is, the neutral axis of each stringer was calculated to be
above mid-depth of each W-section, indicating an imbalance of tensile and compressive
strains within the steel shape. This corresponds to the condition found in Figure 2.6.3.b.
By providing a mechanism for shear transfer, namely the shear stud pockets, some level
of shear load is distributed into the deck. However, as the shear load transferred is less
than what would be present in a fully composite section (Figure 2.6.3.c), the steel
48
stringers and FRP deck observed in this project are termed partially composite. Verifying
this observation were the strain levels recorded by transducers mounted directly to the
FRP deck. It was found that projected strains based on neutral axis computations were
consistent with the strains recorded by the few transducers mounted to the FRP deck.
Figure 2.6.2 – Method used to locate the neutral axis of stringers. Adapted from Bridge Diagnostics
Inc. (2002).
Figure 2.6.3 – Comparison of composite nature stress profiles through a typical deck section (Lenett
et al. 2001)
49
It was noted that the response of each longitudinal transducer pair (top and bottom
of individual stringer) was not completely identical. Results indicated that when the test
vehicle was in close proximity of the strain transducer the top flange, which typically
indicated compression, would respond with a tensile “spike” in readings. Figure 2.6.4
provides a plot of longitudinal strain data recorded. When the test vehicle was
significantly far away from the top sensor the transducer readings would return to their
expected values. It is theorized that the flange, when under direct loading, experiences
localized effects thus affecting the recorded data.
Figure 2.6.4 – Top flange tensile “spike” observed in stringers during live load testing Adapted from
Bridge Diagnostics Inc. (2002).
50
2.7 – The Bridge Street Bridge (Grace et al. 2002; Grace et al. 2005)
Structure B of the Bridge Street Bridge in Southfield, Michigan is unique for a
few reasons. While the double-tee beam system used in the structure is commonly used
in prestressed structure design, the reinforcement used in each girder is quite novel.
Figure 2.7.1 provides a section profile of the bridge. The prestressed concrete stringers
contain CFRP tendons in lieu of conventional steel prestressing tendons. Additionally,
external post-tensioned carbon fiber cables were draped along the lengths of each beam
to provide supplementary longitudinal strength while similar carbon fiber cables were
post-tensioned transversely at each beam diaphragm. The concrete deck is reinforced
with CFRP grids, which is topped with a conventional concrete wearing surface. The
only conventional reinforcement present in each beam is mild steel shear stirrups located
throughout the web of each double-tee. Constructed in tandem with a conventionally
built twin, the bridge is a three-span structure carrying two lanes of traffic. Six of the
beams on Structure B were instrumented for long term monitoring and subjected to an in-
situ load tested to study their behavior relative to AASHTO design procedures (Figures
2.7.2 and 2.7.3).
51
Figure 2.7.1 – Bridge Street Bridge cross section (Grace et al. 2005)
2.7.1 - Materials Used
Each of the three spans in Structure B consists of four adjacent double-tee beams
each reinforced longitudinally LeadlineTM prestressing tendons
(www.mkagaku.co.jp/english/corporate/008.html) and four external, post-tensioned
carbon-fiber composite cables (CFCCTM, www.tokyorope.co.jp/english/). All four
girders in a span were also post-tensioned transversely with CFCC tendons. A lateral
diaphragm cast into each girder provides anchorage for each tendon. Seven such
diaphragms were located in each girder. Horizontal deck reinforcement is composed of
multiple bi-directional NEFMACTM (www.autoconcomposites.com/index.html) grids of
52
0.394” diameter carbon fiber reinforcing bars. Specified 28-day concrete strengths were
7,500 psi for the girders and 5,500 psi for concrete deck topping.
2.7.2 - Instrumentation
As monitoring of this structure was conducted from fabrication to construction
and beyond, a majority of all instruments were installed at the precast facility. All twelve
double-tee beams were instrumented initially to monitor stress levels during fabrication
and prestressing. However, only six beams were instrumented with long-term monitoring
equipment for the in-situ observation. Beams to be monitored in the field contained both
internal and external vibrating-wire strain gages installed at the mid and quarter-span
points of each beam, as well as displacement sensors. At each strain monitoring section,
(quarters and mid-span) gages were installed up both webs of the double-tees. Gages
were located near the bottom of each web, at mid-height, near the top in the decking, and
one in the concrete topping. Figure 2.7.2 illustrates locations of strain gages.
Each beam thus contains a total of 30 gages with only the nine concrete topping sensors
installed in the field.
Figure 2.7.2 – Strain gage location in instrumented spans of Structure B.
53
Positioning of the six long-term instrumented beams was such that the width of
one entire span was instrumented (referred to as the north span) and a single
representative beam was instrumented in the other two spans (Figure 2.7.3). Although
not relevant to the scope of this discussion, it is interesting to note that a load cell was
installed for each longitudinal external post-tensioned cable for the instrumented beams
to monitor their load levels throughout the life of the structure.
Figure 2.7.3 – Long-term instrumented spans of Structure B.
2.7.3 - Load Test and Results
To conduct the load test, two three-axle dump trucks were used in four separate
load cases. The load cases can be classified as interior or exterior beam tests and are
illustrated in Figure 2.7.4. For each test, multiple readings were required, allowing the
vibrating-wire strain gages to settle. Vehicles were located in their desired position and
remained in place for a period no less than five minutes to obtain adequate strain
readings. For every movement during testing settling periods were implemented to allow
the gages to reach a steady state. During the interior beam tests, trucks were positioned
54
for maximum positive bending moment adjacent to the sidewalk on the span. The
sidewalk limits the distance in which a vehicle may approach the exterior beams. One
test was conducted in the fully instrumented north span of Structure B while another was
carried out in the complimentary south span. For the exterior load test the trucks were
positioned to produce maximum positive bending moment near the exterior parapet of the
span. Similar to the interior beam tests, the exterior load tests were conducted in the fully
instrumented north span and also the middle span for comparison.
Figure 2.7.4 – Live-load test cases for Bridge Street Bridge
To produce distribution factors of the structure, the authors combined the data
from the interior and exterior load tests, superimposing strain readings on each beam for
comparison. Distribution factors were calculated based on total strain in a specific beam
relative to total strain of all beams using equation 2.5.1. Overall, it was found that the
calculated distribution factors agreed very well with distribution factors obtained using
the 1996 AASHTO Standard Specifications and the 1998 AASHTO LRFD methods.
55
Additionally it was concluded that usage of the AASHTO specifications was appropriate
for design of prestressed concrete beams externally reinforced with carbon-fiber
reinforcement.
2.8 – Synthesis of Literature
As noted previously, a great deal of information exists pertaining to the topic of
bridge monitoring. However, information directly related to the static, live load testing of
structures is not easily obtained. A vast majority of bridges in the United States are
inspected from a visual perspective only as the initial cost of instrumentation often
prohibits the scientific evaluation of them. Structures selected for monitoring are limited
among the bridge inventory but have been proven to provide valuable insight into their
performance. Monitoring efforts such at Ohio HAM, South Carolina S655, the
Fairground Road Bridge and the Bridge Street Bridge offered insight into procedures
used for successful monitoring of structures. Methods of interpreting data relating to the
distribution of vehicle loads among bridge stringers and evaluation of the composite
nature of each different structure are presented in the research carried out, providing a
rational basis for implementation on the IBRC structure of this study.
The successes of these projects provide a proving ground for use of commercially
available instruments. Complying with the recommendations noted in Section 2.1, The
Ohio HAM Bridge, South Carolina S655 and the Fairground Road Bridge illustrate the
preference of electrical-resistance strain gages for short-term load testing, as well as the
use of high-speed data acquisition systems for data collection. Additionally, the testing
56
of the Bridge Street Bridge illustrates adequacy of using vibrating-wire gages but also
their lengthy acquisition process.
The Fairground Road Bridge illustrates the successful use of removable strain
sensors composed of electrical resistance gages. Extensive amounts of labor were
focuses on attachment of electrical resistance gages to the Ohio HAM Bridge, South
Carolina S655 and the Bridge Street Bridge during fabrication, limiting the requirement
of in-situ installation. Experience of these projects (including the previous, inconclusive
strain gage instrumentation of the De Neveu Creek Bridge) indicates that field bonded
gages is extremely difficult and can limit the usefulness of data obtained. Thus,
removable sensors are preferred for this project to ensure their repeated use over time.
Fabrication of strain sensors in a controlled environment increases consistency among the
sensors and also limits possible damage from peripheral sources, e.g. the environment,
wildlife and possibly vandals.
Cost of instrumentation is also of concern. The suite of equipment utilized in the
four monitoring projects noted incorporated a substantial financial investment. Use of
compact electrical-resistance strain gages bonded directly to the superstructure produces
valuable information at a low cost when the substrate is composed of homogenous
materials such as steel stringers. However, experience has proven that larger, more costly
instruments are required for satisfactory strain data collection on heterogeneous materials
such as concrete. An application of this is noted in the Bridge Street Bridge project, as
larger, internally embedded concrete sensors were utilized. The cost of larger gages or
57
removable sensors frequently exceeds $500 per instrument, commanding a significant
per-gage investment (MnDOT 2005; Schultz 2005). The instrument array specified for
this project, which will be outlined later in the document, includes 32 locations of strain
gages. Considering the per-instrument cost of commercially available sensors and the
financial capital available for this project development of an alternative, cost effective
instrument is desired.
The instrumentation projects noted also illustrate a wide variety of structural
materials used and differing geometric conditions. The Ohio HAM Bridge utilizes
conventional steel-stringer with mild-steel reinforced concrete deck in an integral multi-
span configuration. The South Carolina S655 project uses a similar steel-stringer with
FRP decking as the Fairground Road Bridge, however S655 contains a single span while
the Fairground Road project is an integral multi-span application. Additionally, the
Bridge Street Bridge is composed of prestressed concrete in a multi-span layout, however
each span acts independently. Based on these differences and the success of their tests,
successful short-term strain monitoring is anticipated for the single span, prestressed De
Neveu Creek IBRC Bridge.
Finally, the previous work conducted on the De Neveu Creek IBRC Bridge
provides a baseline for analysis of data. The load deflection data presented illustrates a
global performance of the structure, indicating an overall performance conforming, albeit
conservatively, to AASHTO design recommendations. However, collection of further
data is requires as a number of performance aspects of the novel structure are not fully
58
understood. Collection of strain data pertaining to the strain profile of the girders and
concrete deck will allow for assessment of composite action between the superstructure
elements. Documentation of any variation in the strain profile of the structure is
important and provides insight into its performance over time. Observation of the
transverse behavior of the FRP-reinforced concrete decking is also required.
Assumptions made in the design of the concrete deck require verification if the system is
to be implemented elsewhere.
59
Chapter 3 – Data Acquisition and Strain Measurement
3.0 - Introduction
Usage of electrical instruments to obtain useful mechanical knowledge can take
on many forms. The method in which physical data is most commonly collected for civil
engineering projects is through direct current instruments. Their simplicity and relative
low cost enable researchers to obtain many points of data with an appropriate level of
accuracy. These systems require the usage of a collection instrument, typically strain
gage circuits or other transducer, a data acquisition system and a personal computer to
process the data. A discussion of collection instruments is included later in this chapter.
The data acquisition system and computers used to interpret and record the data collected
are also described in this section.
3.1 – Signal Processing
Within every data acquisition system is a series of modules that translate an
electrical signal into a form that humans can recognize. Early acquisition systems
utilized paper chart recorders or magnetic tape recorders, while today’s systems have
grown into complex networks of analog-to-digital converters (ADCs), high-speed
multiplexers and personal computers (IOTech 2004). Figure 3.1.1 illustrates the layout
of typical data acquisition system. Contained within this section is an introduction to
ADCs, multiplexing of instrument channels, sampling theory, signal amplification and
also noise reduction.
60
Sensors
Signal Conditioning
(Amplification,
Filtering)
A/D
ConversionComputerMultiplexing
Other Sensor Channels
& Signal Conditioning
Figure 3.1.1 – Layout of a typical data acquisition system
3.1.1 – Analog to Digital Conversion
ADC is a process where an electrical signal is converted into a discrete binary
number for purposes of interpreting it within a digital setting. This conversion process
approximates an instance of the signal and assigns it a binary number, which in turn, is
converted into a digital number. The level of complexity in which the approximation
takes place is dependent upon the size of the binary number assigned to analog signal,
which is quantified by the number of bits used in the conversion. ADCs are capable of
producing a resolution of one part in 2n, where n is the number of bits used (Rizzoni
2003). For example, the IOTech DaqBoard 2000 series used for this project contains a
16-bit ADC. Thus it is capable of a resolution of one in 216, or 1/65,536. If 5 Vdc is input
to the system, the maximum resolution available is 5/65,536, or 0.000076 volts (0.076
mV).
61
Many types of ADCs exist, with the most basic being the successive-
approximation ADC. A detailed explanation of this type of converter illustrates a very
basic procedure for converting an analog signal to a digital value. Successive-
approximation ADCs compare an analog voltage to a voltage produced by an internal
digital-to-analog converter (DAC). The DAC produces an analog signal that is compared
to the measured signal, which is prescribed by a series of switches. Each switch
represents one bit of resolution. The first switch activated typically produces a voltage
equal to half the full scale of the circuit. This voltage is compared to the analog value
and if the analog voltage is greater than the output voltage, the DAC will increase the
voltage. If the analog voltage is smaller, the DAC will decrease it. This process is
repeated for the second switch and moves the DAC voltage closer to the analog voltage.
Successive steps are performed to close in on the best approximate to analog voltage until
all the switches have been used. This state is the maximum resolution of the DAC.
While the process may seem lengthy, conversion rates in excess of 1MHz are possible
(IOTech 2004).
Error in ADCs can cause difficulties in producing an accurate approximation of
the analog signal. Common sources of error come from the linearity of conversion, lack
of proper digital coding and electrical noise. Manufacturers of data acquisition systems
take great care to properly calibrate their ADCs and provide recommendations for their
accurate usage. Many types of ADCs exist with significantly more complex methods of
approximating an analog signal. The equipment used in this program utilized a
62
successive-approximation ADC (IOTech 2005a) and peripheral examples of ADCs are
not included within this document.
As multiple sensors are used in large projects, obtaining synchronized data can be
difficult. If an acquisition system samples analog signals at a slow rate, the time
difference between readings of the first and last sensors can be appreciable. For example,
a truck traveling at 45 miles per hour takes only 1.52 seconds to cross a 100’ bridge. If
the sampling rate of the system is 1Hz, only one sensor will be read during the crossing.
The other sensors will not be read during the truck’s crossing. For this reason, high-
speed ADCs are required for rapid acquisition. However, rapid-acquisition ADCs can be
relatively high in cost. To avoid usage of multiple ADCs, a device called a multiplexer is
used. This device rapidly switches between sensor channels and transmits their signals to
a single high-speed ADC for digitizing. While this procedure mimics the usage of
multiple ADCs, it provides a great deal of economy to acquisitions at a suitable sampling
rate (IOTech 2004).
However, it must be recognized that the switching of channels produces data that
are not recorded at the same instance. If time-specific measurements are required Sample
and Hold (S/H) circuits can be used to temporarily store the analog reading from the
sensor. Each S/H is triggered to sample its sensor nearly simultaneously with the other
channels and hold that value until the multiplexer allows the signal through. This allows
for readings to be incredibly close to each other, frequently less than 100 ns apart
(IOTech 2004).
63
3.1.2 – Sampling Rates
As rapid sampling rates are available through the use of high speed ADCs and
swift multiplexers, a brief discussion of sampling rate is warranted. The goal of ADC is
to best preserve the original signal form, thus one may instinctively assume that the
quicker the sampling the better. Through extensive research it has been found that this is
not necessarily the best answer (Rizzoni 2003). Rather, a simple solution exists – the
Nyquist Sampling Criterion. This criterion states that if all frequencies contained in a
signal are less than a specified value, all information pertinent to that signal may be
obtained by sampling at a minimum of twice that value (IOTech 2004). Application of
the Nyquist theorem provides the most accurate generation of data specific to a measured
signal.
Another phenomenon that must be addressed in signal processing is aliasing.
Aliasing has two facets, both of which facilitate incorrect measurements. When sampling
at too slow a rate, signals much lower in the frequency domain than the true signal may
be produced. Figure 3.1.2 illustrates this with a 5Hz sine wave sampled at a 6Hz rate,
which is less then the recommended rate of 10Hz. The low sampling rate incorrectly
produces a 1 Hz wave as shown below.
1Hz wave observed6Hz sampling points
Time (s)
1.0 sec
Actual 5Hz signal
Figure 3.1.2 – Application of the Nyquist Theorem.
64
Additionally, it is common to encounter aliases produced by frequencies equal to
half of the desired frequency or greater. Acknowledging the Nyquist Theorem, the
sampling rate should be increased to more than twice the desired frequency, requiring
that any unanticipated frequencies below the desired signal be prevented by other means.
This stage of signal conditioning must be addressed before any digitizing can take place.
Usage of anti-aliasing filters is the most common method of reducing aliasing from a
signal. These filters allow only frequencies smaller than a prescribed level to pass
through the circuit and are termed low-pass filters. Recognizing this issue, a low-pass
filter was utilized on each individual channel for strain gage measurements to remove any
aliasing present. These filters were set very low (less than 4 Hz) as the measured signals
were expected to be constant, with no oscillation.
This issue of aliasing introduces the process of preparing an electrical signal for
digitizing called Signal Conditioning. This conditioning process works to eliminate any
environmental or other sources that may cause misinformation within the desired signal
and consequently invalidate the information processed by the ADC. Signal
amplification, digital and analog filtering, and signal attenuation are topics directly
applicable to strain gage measurements and are discussed herein.
3.1.3 – Signal Amplification
As a large number of strain measurements utilize an electrical circuit called the
Wheatstone bridge, a brief introduction is warranted. The Wheatstone bridge is a basic
electrical circuit whose resistance changes when the base material is strained. This
65
resistive change can be directly related to the level of strain experienced by the measured
member. However, most applications of the Wheatstone bridge produce very small
electrical changes while in operation, making amplification of the signal relatively
important. Without satisfactory amplification, observation of signal changes becomes
incredibly difficult. Commonly, each sensor channel is provided with its own amplifier
sequence as to preserve customizability among instruments. This enables the user to
obtain information about different types of instruments simultaneously. Many methods
of amplification exist and due to the extreme breadth of the subject, details of electrical
amplification are not contained within this document. However, an overview of signal
amplification and subsequent conditioning used in this project is discussed below.
The IOTech DBK43A module used in strain measurements increases the magnitude
of the measured signal by means of an input amplifier and a scaling amplifier.
Additionally, a signal offset adjustment module is present within the series of amplifiers
to nullify any initial imbalance the circuit may have. The layout of the individual
channels within the DBK43A module is illustrated in Figure 3.1.3. The step-by-step
process is described as follows,
1. The unchanged signal enters the input-gain amplifier from the strain gage sensor
and receives its first increase in magnitude by a multiplier.
2. The signal enters the offset adjust module where any initial imbalance may be
removed.
3. The signal then passes through filtration (to be discussed later), which has a
default amplifier that doubles the signal magnitude.
66
4. Finally, the scaling amplifier then amplifies the signal by another independent
prescribed multiplier
Once amplification is complete, the signal passes into the multiplexer and eventually into
the ADC.
431
Wheatstone
bridge circuitry
2
Signal
conditioning
circuitry
Figure 3.1.3 – Block diagram of an IOTech DBK43A (IOTech 2005b). Further explanation
regarding signal-conditioning circuitry is found in Figures 3.1.4-6 and its corresponding literature.
To establish known values for each stage of amplification, screw-driven
potentiometers termed “trimpots” are used. Manipulating these trimpots on the DBK43A
may change each stage setting within their available range. Four trimpots are provided
for each channel and are described below,
• EXEC – sets the excitation voltage of the circuit
• OFFSET – adjusts the offset voltage of the circuit
67
• GAIN – sets the input amplifier gain (100x to 1250x)
• SCALE - sets the scaling amplifier gain (1x to 10x)
The following description of configuring circuit amplification assumes that voltages are
observed at a computer through the use of software compatible with the data acquisition
system. Computer software is utilized to select a signal path illustrated in Figures 3.1.4
through 3.1.6. The equations governing the amplifier output are identified with each
illustration and may be used to establish the desired amplification gains. Once these
values are set, the signal will be ready for ADC.
Initially, if the circuit contains quiescent voltages or significant bridge imbalances
they may be set to zero by adjusting or trimming the “Offset” trimpot. While this offset
has a limited range (-1.25mV to 5.0 mV), it is satisfactory for most applications (IOTech
2005b). The signal path of the offset adjust can be seen in Figure 3.1.4. Note that
multiple inputs are included prior to multiplexer (MUX A). The Wheatstone bridge, a
reference voltage of 5 mV, and an electrical ground may be selected using the software.
Vout
Ground
Figure 3.1.4 – Signal path of the “OFFSET” trimpot (IOTech 2005b).
68
To set the input amplifier gain (GainINPUT) at a known value, a reference voltage
of 5mV (Vreference) is applied to the signal conditioning circuit while the voltage drop
across each stage is read. To obtain the desired input gain, the “Gain” trimpot is adjusted
until the specified output voltage, Vout, is reached. This voltage is calculated using the
expression below in Figure 3.1.5. Note that in Figure 3.1.5 the signal path does not enter
the scaling amplifier at any time. Furthermore, the signal path does cross through the
filter section, which acts as a small signal amplifier. This stage has a default, but
constant, amplification gain (GainFILTER).
Vout5.0 mV
( )( )( )( )( )( )0.005 2.0
out reference FILTER offset
offset
V V Gain V
V
= −
= −
INPUT
INPUT
Gain
Gain
2.0FILTERGain = 0offsetV ≈,
referenceV =
Figure 3.1.5 – Signal path during adjustment of the input amplifier gain (IOTech 2005b).
Similar to the input gain, the scaling gain (GainSCALING) is set by activating the
signal conditioning circuit and applying a 5mV reference potential, producing an
amplified output. Adjustment of the “Scale” trimpot until the desired output voltage is
reached sets the scaling gain at the specified level. The expression governing this setting
is below. Figure 3.1.6 illustrates the signal path during this process.
69
Vout5.0 mV
( )( ) ( )( )( )( )( )( )0.005 2.0
out reference INPUT FILTER offset
INPUT offset
V V Gain Gain V
Gain V
= −
= −
SCALE
SCALE
Gain
Gain
referenceV =
Figure 3.1.6 – Signal path during adjustment of the scaling amplifier gain (IOTech 2005b).
As shown in Figure 3.1.3, each of the DBK43As eight individual channels used in
this project contains the sensor’s circuitry, an individual amplifier series, and two
filtering options. There is no interaction between adjacent sensors, nor their amplifiers or
filters.
3.1.4 – Signal Filtering
Filtering a signal can be addressed in both the digital and analog arenas. While
many types of filtration exist, the most common forms are the Butterworth, Chebyshev,
and Bessel filters. Each type may be used for high, low or band-pass applications, but the
discussion herein is limited to low-pass filtering. Low pass filters allow only frequencies
within a signal below a specified cutoff frequency, ωc, to be amplified, or pass through,
while all other frequencies are attenuated (Rizzoni 2003). Figure 3.1.7 illustrates a
typical response of a low-pass filter. It can be seen that preferred frequencies are less
than the cutoff frequency are amplified by a gain of A, acknowledging a tolerance of A±ε.
70
All frequencies greater than the cutoff frequency are then attenuated to lower gain levels.
This effectively gives preference to those frequencies lesser than the cutoff frequency by
allowing them to be amplified by significantly large gains. The Stopband signifies
frequencies that are amplified by a specified minimum gain of Amin, which is typically
very small causing them to be overshadowed by the Passband frequencies. As Amin and
the lower Passband frequency A-ε are not equal, an attenuation gap is caused where
frequencies are amplified by a gain greater than the minimum, but are not affected by the
maximum amplifier gain A.
Frequency, ω
Stopband
Passband
Filter Gain
ωc
Cutoff Frequency, ωc
A
0
Attenuation of signal
amplificationA-ε
Amin
A+ε
Figure 3.1.7 – Typical low-pass frequency response.
It can be seen that attenuation of undesired frequencies is not instantaneous at the
cutoff frequency, but rather has a varying response. Figures 3.1.8 and 3.1.9 illustrate two
common types of low-pass filters. Figure 3.1.8 shows the characteristics of a Butterworth
filter, which exhibits a flat response across the passband and attenuates unwanted
frequencies quite steeply.
71
Figure 3.1.8 – Butterworth low-pass filter response (Rizzoni 2003).
Figure 3.1.9 illustrates a Chebyshev filter, which has an even steeper attenuation rate but
not as flat of a response across the passband. Note the movement of the amplitude
response for the second through fourth order Chebyshev filters. A third type of filter is
the Bessel filters, which has a much shallower rate of attenuation (IOTech 2004; Rizzoni
2003).
Figure 3.1.9 – Chebyshev low-pass filter response (Rizzoni 2003).
As noted previously, signal filtering is encountered within the DBK43A module
and is of analog type. Included with the module was a 3.7Hz, third-order Butterworth
low-pass filter, which attenuates signals with frequencies greater than 3.7Hz. As can be
seen in Figure 3.1.3, the filter is located on each channel before the multiplexer, but after
72
the initial input amplifier. This location is beneficial as it allows the filter to have an
ideal signal-to-noise ratio (IOTech 2004). Usage of this filter eliminates ambient noise
caused by environmental sources (e.g. fluorescent lighting or radio signals) and also
reduces any aliasing caused by these sources. Through testing, it became evident that
usage of these filters is necessary, as elimination of interference sources is extremely
difficult. Figure 3.1.10 illustrates the need for filtration with an unstrained, quarter-
bridge strain gage circuit. Figure 3.1.10(a) shows a “dirty” signal with interference from
radio waves, lights, power systems and aliasing. Figure 3.1.10(b) shows the drastic effect
that the analog filter has on the signal, eliminating nearly all the high-frequency noise
(radio, lighting, power systems). Finally, digital filtering removes the remaining noise,
presumably aliasing from higher frequency signals.
(a) Unfiltered Signal (c) Signal with Analog and
Digital Filtering
(b) Signal with Analog
Filtering Only
Figure 3.1.10 – Comparison of filtered (b & c) and unfiltered data (a) (DASYLab 2004).
Additional filtering can be provided in the digital realm. Very small amounts of
electrical interference were observed after the analog filter was enabled. Thus, use of
digital filtering on all strain channels was utilized to obtain the relatively noise-free signal
73
illustrated in Figure 3.1.10(c). The digital filter used in this project was a 2 Hz, second-
order Butterworth filter
The DBK43A module offers an additional source of signal conditioning similar to
filtering termed AC Coupling. Employment of this option requires that an internal
electrical jumper located on the modules circuit board be removed, allowing the signal to
pass through a capacitor, which removes the DC component of a combined AC and DC
signal. The signal yielded by enabling this option is a cleaner AC signal, without a shift
due to the DC signal. Figure 3.1.11 graphically illustrates this procedure.
Figure 3.1.11 – (a) standard wave composed of AC and DC signals, (b) AC Coupled wave
(National_Instruments 2005).
Typically, this option is used only for signals in the AC arena or for cyclic DC
measurements with high-frequency signals and was not observed to be effective for this
project (National_Instruments 2005). Additionally, all instruments to be used in this
project are part of DC circuits that output extremely low frequencies, eliminating any true
74
usefulness of AC coupling. In fact, the only AC signals observed in this project are
caused by environmental noise (e.g. fluorescent lights).
Aside from filtering, other methods of obtaining more accurate signals can be
incorporated into measurements. Measurement sensors are rarely located a small
distance from the data acquisition system warranting the use of lead wires. These lead
wires may only be a few feet long for a laboratory setting. However, large projects such
as bridge monitoring require the usage of several hundred feet of wire. Unfortunately,
long wires allow for significant noise production within a signal and must be addressed.
A common method used to reduce this effect is the installation of shielded or twisted-pair
wire. Shielded wires are preferred for measurement as they eliminate most forms of
interference. If used, however, the shielding for each wire must be connected to a stable
ground near the acquisition system. Electrical grounds are may be found on the chassis
of the ADC, the cable supplying power to the modules, or by connecting directly to the
earth. Grounding should never be at the instrument end nor should the system ever have
two grounds, as these may produce conductive loops and induce an peripheral voltage in
the signal (Rizzoni 2003). Although it exhibits excellent noise attenuation when
grounded properly, shielded wire is expensive and also vulnerable to electrical induction
when located near large current sources (Rizzoni 2003). On the other hand, twisted-pair
wire is excellent in combating noise in large current environments but lacks shielding and
is vulnerable to radiated noise. The twisting path of each wire causes the electromagnetic
field produced in each wire to cross at regular intervals, effectively canceling each other
out (Omega 2000). Additionally, for twisted pair wire to work properly, each wire must
75
carry a current to achieve canceling. For this project it was not feasible to use either
method prescribed resulting in the need to employ filtering. Lead wires used for this
project were composed of a three-wire Wheatstone bridge circuit (detail may be found in
section 4.1), independently twisted with an inactive wire. It is recommended that for
strain measurements of bridge structures shielded wire be employed if the measuring
environment contains a large amount of radiated noise. It is unexpected to encounter
large currents during bridge monitoring as they are primarily found in industrial
environments and not outdoors.
3.2 – Measurement with Electrical Resistance Strain Gages
Electrical resistance strain gages are devices used to measure strains in a wide
variety of applications. When strained, each gage responds with a change in electrical
resistance that is proportional to the magnitude of strain the gage is subjected to.
Monitoring of this varying resistance value yields information that can be directly
correlated to strains found in the material being studied. Typical electrical resistance
strain gages are composed of a backing material and an electrically resistive network.
When the backing material is deformed, the resistance of the network either decreases or
increases. Decreases in resistance are caused by a compressive strain while a tensile
strain produces an increase in resistance. Typically, these gages are employed as part of
a resistive network designed to produce an electrical output when excited by a constant
voltage source. Figure 3.2.1 illustrates a plan view of a typical strain gage.
76
Figure 3.2.1 – Typical strain gage (www.vishay.com)
The most common DC circuit used in strain gage measurements is the Wheatstone
bridge. Invented by Samuel Hunter Christie in 1833 and later popularized by Sir Charles
Wheatstone, the bridge contains two arms that when strained produce a relative change in
voltage (Wikipedia.org). This voltage difference is measured between the two mid points
of each arm, denoted in Figure 3.2.2 as nodes a and b. This arrangement of strain gages
and/or resistors has proven to provide excellent sensitivity when measuring the minute
resistive changes that result from strain of the gage.
Figure 3.2.2 – The Wheatstone bridge.
The three most common forms of the Wheatstone bridge are the quarter, half and
full bridge configurations. A quarter bridge configuration has a single strain gage (SG1)
and three additional completion, or dummy, resistors (Ri). During testing the strain
77
gage’s resistance varies while the completion resistors remain static. A half bridge
network utilizes two strain gages and two completion resistors. In this arrangement, one
entire arm, or half the circuit is variable, thus the moniker, half-bridge. A full bridge
configuration requires the use of four strain gages and zero dummy resistors. Examples
of these configurations can be found in Figure 3.2.3.
Figure 3.2.3 – Typical configurations of the Wheatstone bridge.
Of these three configurations the full bridge is the most sensitive, whereas the
quarter bridge is the least. The high degree of sensitivity of full bridge configurations
and its fewer sources of error make it ideal for strain measuring. However, installation of
four gages can be labor and cost intensive. Half or quarter bridge circuits are typically
used when installation of four gages is not feasible. While quarter bridge circuits offer
the least sensitivity, they can be constructed rapidly. Additionally, quarter bridge circuits
offer reliable measurements so long that the issues of signal noise and error sources are
properly addressed. Signal noise is most commonly eliminated by use of filtering and
shielding while error sources may be compensated by use of mathematical methods.
Both are addressed elsewhere in this chapter.
78
Recognizing this, the quarter bridge configuration was chosen for this project.
The following is an overview of quarter bridge behavior and the calibration process used
for each gage.
To monitor the electrical response of each circuit, an initial state must be
identified prior to testing. The ideal state is one in which the resistances on each side of
the bridge are equal. If an excitation voltage, Vexec, is applied to the bridge, each resistor
will have an equal resistance drop and the ratios of the upper and lower resistors on both
left and right sides will be unity. Thus, the resulting output voltage across nodes a and b
is zero. This is illustrated by using the resistances found in Figure 3.2.4 and the
following expressions for output voltage,
c d b aab exec exec
a c b d b d a c
R R R RV V V
R R R R R R R R
= − = − + + + +
(3.2.1)
Clarifying, if the ratios Ra/Rc and Rb/Rd both equal 1.0, the bridge is said to be balanced
and yields an output of zero. Note that the ratios of each side of the bridge control the
output of the circuit, not just the individual resistances.
Figure 3.2.4 – Diagram of variables used in calculations.
79
Data acquisition systems monitor the voltage difference between nodes a and b,
which are directly effected by resistances of each completion resistor or strain gage in the
circuit. As it is not possible to obtain resistors that are exactly equal in resistance and
thus initial states of imbalance will exist in all Wheatstone bridges. This imbalance can
be corrected by either mathematically subtracting the initial voltage differences (Vab) or
by adjusting the offset adjustment trimpot outlined in section 3.1. Constant manipulation
of the offset adjustment trimpot is unreasonable during measurement and thus
mathematical means are typically used. It has been found that low levels of bridge
imbalance do not affect measurements when only a small portion of the strain gages
measurement range is used. If a majority of the strain gages range is required (typically
5% of the gage length), elimination of bridge offset should be addressed. Recall that for
a quarter bridge circuit only one of the four resistors is variable.
If resistor Rb is replaced by an equivalent resistance strain gage and strained by a
magnitude ∆R, the resulting output will be,
c dab exec
a c b d
R RV V
R R R R R
= − + + ∆ +
(3.2.2)
Note that if the gage experiences tension, ∆R will increase, which increases Vab. The
opposite is true for compression.
Often, it is required to calibrate or verify the accuracy of a strain gage within a
resistor network. Both direct and indirect methods of calibration are available to the user.
Direct methods require a known mechanical input to the system to which the output is
80
compared. For instance, load transducers may be directly calibrated with a known mass.
However, direct calibration of a strain gage circuit by a known strain requires precise
equipment not ordinarily available (Micro-Measurements 2004b). Indirect calibration
can be achieved by electrically simulating the presence of a mechanical input. Most
frequently this is performed by shunt calibration. Shunting is a procedure where a
resistor of large impedance is placed in parallel with the initial resistor and via Ohm’s
Law, a small change in equivalent resistance results. It is important to note that during
shunting, the gage is not strained in any way but when coupled with the large impedance
the two are “seen” electrically as a slight drop in resistance. This causes the Wheatstone
bridge circuit to “feel” a simulated compressive strain in the gage. Recall that a drop in
resistance signifies a compressive strain. Tensile strains may also be induced in the
bridge by shunting a dummy resistor in parallel with the completion resistor after the
gage. Figure 3.2.5 displays two shunting locations and their simulated effect.
+Vexec
-
+Vexec
-
RGage
RGage
RdRc
Ra
RdRc
Ra
a b a b
Figure 3.2.5 – Simulated strain via shunt calibration.
The strain simulated may be obtained by usage of a term describing the sensitivity
of each gage. This term is referred to as the Gage Factor and is typically provided by the
81
manufacturer of strain gages. The gage factor is defined as the instruments propensity to
change resistance with straining. Symbolically, it is defined as,
g gR R R R
GFL L ε
∆ ∆= =∆
(3.2.3)
where ∆R is the change in resistance of the gage relative to its original, unstrained
resistance, Rg. L is the length of the gages resistive array, while ∆L is the change in
length that occurs simultaneously with ∆R. Recall that strain, ε, is the change in length
relative to its original length, or ∆L/L. This expression may also be re-written in terms of
strain,
gR R
GFε
∆= (3.2.4)
Note that for an increase in resistance the expression yields an increase in strain, or a
positive value indicating tension. The opposite is true for compression.
As noted previously, it is often common to shunt, or place a large impedance in
parallel to the strain gage itself, causing a simulated compression strain in the bridge. It
is prudent to calibrate the gage with a simulated strain roughly equal to the largest
anticipated value. This maximizes the output of the circuit by inducing the full resistive
range of the gage. Manipulation of the gage factor equation produces the following
expression for direct calculation of the required shunt resistance needed.
( )
g
shunt g
simulated
RR R
GF ε= − (3.2.5)
By shunting the strain gage with the shunt resistor, Rshunt, the equivalent resistance of that
specific arm will decrease and simulate a desired compressive strain. The equation below
82
illustrates the effect that a shunt resistor has on the output voltage, Vab, of the bridge. All
variables are indicated in Figure 3.2.5 where RGage is a strain gage and Ra, Rc and Rd are
dummy resistors of equal resistance.
( )
c dab exec
a c Eq d
R RV V
R R R R
= − + +
(3.2.6)
where the equivalent resistance of the shunted gage is,
1
1 1Eq Gage
Gage Shunt
R RR R
−
= + <
(3.2.7)
It can be seen that if REq becomes smaller while all other variables remain
constant, Vab will be negative, signifying compression. Electrically, shunting RGage with
RShunt causes decrease in equivalent resistance which is referred to as REq. Satisfying
Ohm’s Law, this decrease in equivalent resistance causes an increase in current across
both RGage and Rd. However, as the resistance of Rd is now greater than RGage more
voltage will drop across Rd. By subtracting the voltage drop across Rd from the
corresponding voltage drop no the opposite side, a negative result is produced, which is
observed as compression.
A Wheatstone bridge may also simulate a tensile strain with by shunting.
Referring to the rightmost illustration in Figure 3.2.5, the gage is not shunted and does
not experience an equivalent resistance change. However, the dummy resistor is placed
in parallel with the shunt resistor and experiences a drop in equivalent resistance. Thus,
the entire shunted arm experiences a greater, but uniform current flow that increases the
voltage drop across the gage, Rb. As noted before, an increase in voltage across the gage
83
is viewed as tension. Detailed examples of compressive and tensile shunt calibration
calculations can be found in Appendix B.
While shunt calibration is quite simple, addressing measurement errors and signal
attenuation of Wheatstone bridges involves many issues, the most pertinent of which are
discussed in the following sections.
3.3 – Strain Gage Measurement Errors
While calibration of the gage is crucial to accurate measurement, sources of error
exist and must be addressed. Lead wire attenuation, thermal effects of gages and wires,
and strain gage non-linearity are the most common sources of error in measurements and
each are addressed in the following section. It is important to note, however, that error
sources may be addressed by numerous computer software packages available for data
acquisition. Often these packages do not disclose the methods used in addressing error
sources and, thus, the validity of such requires trusting the programming source. The
following section outlines the basics of error correction and only provides numerical
modifiers that may be applied to recorded data for error correction.
The desensitizing of a gage due to lead wire resistance is easily avoided. Figure
3.3.1 illustrates two commonly used quarter bridge strain gage circuits.
84
Figure 3.3.1 – Quarter bridge strain gage configurations (Micro-Measurements 2005c).
For the two-wire circuit (Figure 3.3.1(a)), it can be seen that the lengthy lead wires act as
small resistors and cause a voltage drop across them. When the gage is strained these
additional potential drops will act in a parasitic manner, effectively desensitizing the
voltage reading of the gage. The effect is similar with a three-wire circuit (Figure
3.3.1(b)), but only a single length of lead wire desensitizes the reading as each arm of the
active side of the circuit experiences the same lead wire resistances, effectively canceling
them out (Micro-Measurements 2005c). Correction of this scenario may be made be the
following relationship.
g Lactual read
g
R R
Rε ε
+ =
(3.3.1)
85
where Rg is the gage resistance and RL is the lead wire resistance. Also, RL is equal to
two lengths of lead wire for a two-wire circuit and a single length for a three-wire circuit
(Micro-Measurements 2005a). The systems used in laboratory settings often contain
lengths of lead wire short enough that they contribute negligible additional resistance to
the circuit. For example, a circuit with a 350-ohm strain gage in a three-wire
configuration with 30’ of lead wire has 1 ohm of lead wire resistance. Using equation
3.3.1 this length of wire produces only a 0.28% difference. Consideration of this error
source is warranted for field implementation but the effects are typically small.
Thermal effects of strain gage circuits also warrant consideration. Both lead wire
and gage temperature affect readings and both are discussed herein. Gages are typically
manufactured with a backing material that closely mimics the thermal expansion
characteristics of the base material the gage is to be installed on. For most applications
this approach eliminates most sources of thermal expansion/contraction error in the gage.
However, when supplying a large excitation voltage to a gage, the individual strain gage
may act as a heat source if a proper heat-sink is not provided to distribute head generated
away from the strain gage (Micro-Measurements 2005b). The most common example of
a proper heat sink is the substrate that the strain gage is bonded to. For this reason,
measurements on metals normally do not raise concern while measurements on polymers
and other non-conductive materials do.
The following calculation is representative of the heat-sink conditions found in
this project and are provided as an example. The power dissipated by a strain gage and
86
the power density in a strain gage grid can be estimated using the following equations
(Micro-Measurements 2005b),
Power dissipated in strain gage grid, 2
4exec
Gg
VP
R=
i
[watts] (3.3.2)
Power density in strain gage grid, GD
g
PP
A= [watts/in2] (3.3.3)
If a 350-ohm strain gage grid is 0.25” long and 0.12” wide and nylon is the base material
onto which the gage is adhered (PD = 0.15 watts/in2), the following excitation voltage is
appropriate for the gage (Micro-Measurements 2005b),
( )2 2 350 0.15 0.25 .012 2.51exec g D gV R P A= × × = × × × = [volts] (3.3.4)
This calculation of the excitation voltage (Vexec) demonstrates that an excitation voltage
greater than 2.51 volts will generate more heat than what can be dissipated efficiently in
the base material. This produces elevated temperatures in and also near the gage and
ultimately leads to errors in strain measurements. Proper selection of strain gage
excitation is of significant concern, especially since gages are likely to be active for an
extended period of time during testing.
As mentioned before, elevated temperatures in lead wires can also cause
significant error. Changes in temperature directly affect the resistance of lead wires,
having a similar effect to that of lead wire attenuation. Error produced by large lead wire
resistances in a two or three-wire circuit can be compensated for similarly to that of lead
wire attenuation. To minimize error sources, use of the three-wire quarter bridge circuit
is recommended.
87
Strain gage non-linearity is another common source of error in strain
measurement. Although primarily effected only at large strain levels, the quarter bridge
arrangement is the most susceptible to non-linearity and must be addressed accordingly.
The non-linear nature of the bridge stems from the electrical behavior of the circuit when
gages are strained. Initially the bridge may be approximated as balanced. Realistically,
the bridge is not perfectly balanced but very near this state. The following example
illustrates the non-linearity of a quarter bridge strain circuit (Micro-Measurements
2004b). The output voltage of the circuit may be expressed in the non-dimensional form
below,
Gageo b a a
exec b d a c Gage d a cinitial
RV R R R
V R R R R R R R R
= − = − + + + +
(3.3.5)
Recall that Rb = RG is a strain gage in a quarter bridge circuit from Figure 3.2.5. When
the circuit is strained, the active arm(s) undergo a resistive change that disrupts the
balanced condition. The output voltage changes as follows,
o G a
exec G d a cstrained
V R R R
V R R R R R
+ ∆= − + ∆ + +
(3.3.6)
where ∆R is the change in resistance of the gage due to straining. To obtain the change in
voltage due to straining, the following expression is used.
o o G G
exec exec G d G dstrained initial
V V R R RV
V V R R R R R
+ ∆∆ = − = − + ∆ + +
(3.3.7)
Note that resistors Ra and Rc do not affect the output voltage in any way. Acknowledging
the assumed initial condition where Ra = Rb = Rc = Rd, This expression can be further
expressed in the following form,
88
4 2
G
G
RR
VR
R
∆∆ =
∆+
(3.3.8)
By substituting the Gage Factor equation (Eqn. 3.2.3) into the above expression, a
relationship for change in voltage in terms of gage factor and strain is available.
( )
2( )
4 2 4 4(2 )
GF GF GFV
GF GF
ε ε εε ε
∆ = → −+ +
i i i
i i
(3.3.9)
The non-linear nature of this bridge configuration is caused by the fact that as the
gage is strained and brought out of balance, the current running through that arm of the
bridge will change. However, the change in current is not proportional to the change in
resistance. As the gage’s resistance changes, the current through that arm in the circuit
changes in the opposite direction. Fortunately, for applications where strains are small
(less than 1000µε) nonlinearity does not significantly affect readings and allows for
neglect of the non-linear behavior. For this reason nonlinear error correction was not
used in this project. Typically, if error correction is required for measurements, Table
3.3.1 provides expressions to correct strain readings in a number of Wheatstone bridge
configurations. Figure 3.3.2 illustrates the affect that strain gage nonlinearity has on
measurements.
89
1% error at
10,000 µεµεµεµε
Figure 3.3.2 – Nonlinearity errors for tensile strain in bridge circuits (Micro-Measurements 2004a).
Table 3.3.1 – Non-linearity correction factors of Wheatstone bridges (Micro-Measurements 2004a).
90
3.4 – String Potentiometers and Linear Position Sensors
Both string potentiometers and linear position sensors fall into a category referred
to as transducers. A transducer is a device that converts one type of energy in to another
type of energy. The transducers used in this project convert mechanical energy, which is
the physical displacement of the material, into an electrical energy via the voltage drop
experienced. A string potentiometer (also referred to as a string “pot”) is composed of a
drum with a string or wire is wound about it, a coil spring to provide resistance and a
sensor to monitor rotation of the drum. As the string displaces, the drum rotates, causing
a change in the output of the transducer. For example, a UniMeasure PA Series string pot
with a 30” range will provide 33mV of output per voltage excitation per inch of
displacement (UniMeasure 2005). If an excitation of 10 VDC is applied to the
transducer, the output voltage at the sensor’s full displacement can be calculated as
follows.
( )( ) ( )33 / / 0.033 10 30 9.9out DCV mV V in mV V in volts= = = (3.4.1)
Note that the output voltage is very near the excitation value. This allows the transducer
to produce the maximum output voltage for the applied range of measurement.
Linear position sensors operate in a similar fashion as string pots. However, in
lieu of a rotating drum, these devices have a solid shaft located inside of a sheath and a
movable resistive contact typically referred to as a “wiper.” The wiper is rigidly affixed
to the shaft and as the shaft displaces the resistance of the sensor changes. This provides
a varying voltage output relative to the shaft’s displacement. A typical circuit is
illustrated in Figure 3.4.1.
91
While a linear displacement sensors can be more accurate than string pots, their
size often limits their use (IOTech 2004). Due to their need to house a solid displacement
shaft, lengths of linear position sensors are typically more than twice their displacement
range. For large displacement measurements, string potentiometers are the preferred
device. Measurement ranges greater than 60 inches are readily available from a number
of manufacturers. Examples of both can be found in Figures 3.4.2 and 3.4.3.
+VExcitation
+VSense
-VExcitation
-VSense
“Wiper”
Electrical “jumper”
Transducer
Figure 3.4.1 – Circuit diagram of a typical three-wire transducer. An electrical “jumper” is provided
to short the negative voltage excitation signal to the appropriate voltage sense terminal.
92
Measuring
string
Figure 3.4.2 – 30-inch String Potentiometer. Figure 3.4.3 – 4-inch Linear Position Sensor.
Manufacturers of string pots provide calibration factors for their instruments;
however, it is fairly simple to calibrate a displacement transducer. In the laboratory
setting, it is relatively easy to monitor and verify a displacement transducer’s operation.
For example, all linear position sensors used in laboratory testing for this program were
installed in their intended location and calibrated prior to any testing. Verification of
accuracy was conducted in the following manner. An initial reading was observed on the
computer through the data acquisition system from the sensor in its original, unmoved
location. This value was nulled by the user to obtain a “zero,” or initial point. The
sensor is then displaced a prescribed amount by a machinist gage block and the output
voltage is recorded. Via software, a linear relationship is developed using these two
points (initial and displaced) to translate any sensor movement during testing. Figure
3.4.4 provides a schematic of this linear calibration procedure. From this relationship,
93
any voltage change of the sensor will correspond to its relative displacement on the line
shown.
Voutput
δdisplaced
Linear calibration line
Initial Point
(0 volts, 0 displacement)
Displaced Point
for calibration
Figure 3.4.4 – Linear calibration of sensors.
3.5 – DASYLab Data Acquisition Software
To interpret the output of the ADC used for this project, a computer program
called DASYLab was utilized. The program’s flexibility in interpreting information sent
from the DaqBook to the computer made it an outstanding choice for real-time data
acquisition. DASYLab is an icon-based program that enables the user to visualize the
various operations being performed on the input signals. Figure 3.5.1 (below) illustrates
a completed DASYLab worksheet ready for data acquisition of four quarter-bridge strain
gage channels and two transducer channels.
94
Figure 3.5.1 – Data acquisition worksheet. All screen shots are taken from DASYLab (DASYLab
2004).
Each icon is referred to as a module, which may perform a task as simple as an
on/off switch or may perform complex operations such as digital filtering of the signal.
Operation of the modules is performed in a left-to-right manner, starting with the signal
input (typically from the ADC) and onto the user-defined modules. The breadth of
options available for data processing in the program is substantial and discussion herein
is limited to items utilized for this project only.
95
The following explanation of DASYLab corresponds to construction of this
worksheet, which requires the real-time observation of the input channels mentioned, but
also signal conditioning and user-actuated recording of data. This generic experiment
configuration represents a similar worksheet used in the laboratory experimentation
carried out during the course of this project. Figure 3.5.2 provides a logical map of
operations performed during acquisition.
Figure 3.5.2 – Logical map of software configuration. Signals from the ADC pass through filtering,
calibration and unit conversion and are recorded by the software.
To interpret information being sent from the ADC, the user starts an experiment with
a blank “worksheet” in which modules may be installed and connected in a variety of
ways. However, prior to construction of the worksheet, the program requires that each
exterior signal-conditioning module used in the data acquisition be configured within
DASYLab. The following pieces of data acquisition equipment were used:
• Signal Conditioning – IOTech DBK65 – (2) Transducer channels
• Signal Conditioning – IOTech DBK43A – (4) Strain Gage channels
• Analog-to-Digital Conversion – IOTech DaqBook 2000
Communication between the ADC and the personal computer was established via
direct Ethernet connection in accordance with the manufacturer’s recommendations.
Although the ADC is capable of remote operation on a computer network, the ADC and
96
computer were directly connected for testing. To configure the signal modules, each
DBK device was added in the program’s Hardware Setup section, located in the
Experiment menu (Figure 3.5.3). While only one DBK43A unit and the DBK65 unit
were used for laboratory testing, Figure 3.5.3 indicates that the four units physically
present the Marquette laboratory have been configured. Once a unit is configured in
DASYLab, it is available for installation on the experiment’s worksheet.
3.5.1 - Installation of ADC Modules
To install modules on the DASYLab worksheet, they may be first selected in the
Modules menu or the provided toolbar. The Modules menu contains all the modules of
DASYLab, organized by their function in to the following categories: Input/Output,
Trigger Functions, Mathematics, Statistics, Signal Analysis, Control, Display, Files, Data
Reduction, Network or Special. More frequently used modules are available on the
toolbar located on the left side of the program window for rapid access. Once a module
is selected (signified by the mouse pointer changing to an oil can) it may be placed by the
user anywhere on the worksheet by left-clicking. Modules may not be located on top of
each other, however.
97
DBK Modules
connected to the
DaqBook
Figure 3.5.3 – Hardware configuration window.
Following the operation map provided in Figure 3.5.2, the ADC inputs are placed
on the DASYLab worksheet. To obtain transducer signals, the DBK65 was selected,
while the DBK43A will convey strain gage signals. Figure 3.5.4 shows the two ADC
modules located on the worksheet. Note that each unit is given a default system name
that corresponds to its channel on the DaqBook. For example, the strain gage module
placed on the worksheet is on DaqBook channel #0, hence the name DBK43A-10:A1.
Similarly, the transducer unit is on channel #3, therefore the name DBK65-13:A1 is
given.
98
DBK Modules
expanded as required
Default DBK
Modules
Figure 3.5.4 – Hardware configuration window on the main worksheet.
Once the input modules are located on the worksheet, they must be expanded to
the required number of active channels. Recall that the DBK43A requires four strain
gage channels while the DBK65 needs two transducer channels (Figure 3.5.4). By
double-clicking on the left mouse button of the individual module, each may be expanded
as necessary. Channels may be made active my double clicking; the left mouse button
activates a channel while the right deactivates it. Note that the user must specify the
range of each individual channel. Figure 3.5.5 illustrates the bipolar (±5.00 volts)
specification for strain gage channels. The transducer channels were specified with a
bipolar 10 volt range.
99
Bipolar Range
Active Channels
Figure 3.5.5 – Expansion of analog inputs in the DBK43A module.
3.5.2 - Installation of Digital Filtering
Following the flow chart for the experiment shown in Figure 3.5.2, filtering is
desired for each channel. Acknowledging that multiple channels of data are required, a
useful feature of DASYLab may be utilized: Global Variables. These variables are static
values that the program retains throughout an experiment. Individual variables may be
read by other modules on the worksheet and can also be modified during the experiment
by the user. These variables may be accessed in the Options menu. For this example
Global variable #1 was defined as 2.00 Hz for use in all channel filters and was given an
appropriate name. Figure 3.5.6 illustrates the dialog box for global variable definitions.
100
Manually Input
Value
Available Global
Variables
Figure 3.5.6 – Defining global variables.
The Filter module was then placed on the worksheet for each DBK unit and
expanded to the required number of channels. Connection of modules on the worksheet
is performed by clicking on a module output (located on its right side), activating a
connection line. The connection line is then attached to the desired module with another
click. Recall the left-to-right flow of signal through modules mentioned before. Multiple
lines may be established simultaneously by touching the left side of the module to the
right side of the previous module and releasing. Once the filter modules are located and
connected properly, the filter properties of each individual channel must be specified.
Figure 3.5.7 illustrates the specification of global variable #1 for the filter channels while
Figure 3.5.8 illustrates the filter modules connected to the ADC modules on the
101
worksheet. Additionally, the type, characteristic behavior and order of filter must be
specified.
Figure 3.5.7 – Defining filtration properties for each channel within the filter module dialog box.
Right-clicking the mouse may access the menu.
Global Variable
specified as low-
pass filter
Figure 3.5.8 – ADC and filter modules connected on the worksheet.
102
3.5.3 - The Black Box Module
Once filter modules are installed for each DBK unit, the calibration of each must
be installed. This series of modules will allow for active calibration of the strain gages
and also the transducers.
To simplify the display and also shorten construction time another feature of
DASYLab will be used. The program has the ability to store a generic series of modules
on a separate, sub-worksheet called a Black Box, which can be imported to worksheets
instead of repetitively re-building similar modules. To illustrate use of this feature, a
black box will be constructed for the DBK43A strain gage unit, stored and then imported
to the worksheet in duplicate for the DBK65 transducer unit. To start, a black box
module is placed on the main worksheet near the DBK43A and opened. Once the black
box is opened, the background of the worksheet changes color to signify the change in
locale that the user is operating in. Figure 3.5.9 illustrates this process. Note that the
black box’s worksheet (right most image) has no modules located on it.
Figure 3.5.9 – Locating a new black box on the main worksheet (left) and opening the black box
(right). Note the color change of the background, distinguishing between the two.
103
An Export/Import Module is placed on the black box worksheet and, when
prompted, the user specifies the module as an “Import Data” module. This module
establishes communication between the main worksheet and the black box, effectively
conveying the signals from the main worksheet into the black box. This module is
expanded to the appropriate number of channels and closed. As this example currently is
focused on the strain gage module, four channels will be specified for the import module.
Once the signal is available in the black box, a number of modules will be
required to complete the calibration of the gages and the unit conversion from voltage to
strain. Figure 3.5.10 illustrates all the modules to be installed in the black box for
calibration and unit conversion of the signal. The modules in Figure 3.5.10 are not
connected, but descriptors of their function in signal processing are noted.
104
1
Signals are
sent to the
Offset module…
…then passed
into a
Digital meter…
…which captures
data for
calibration
Global variables are read by
the Scaling module,
converting voltage into strain
and displaying them in
another digital meter
Control switch and
Action module for
Offset Adjust
Figure 3.5.10 – Modules installed in the black box. The signal path and module functions are noted.
3.5.4 - Offset Adjustment of Signals
To complete calibration and unit conversion of the signal, three stages of signal
process are required:
• Removal of quiescent signals,
• Establishment of calibration for linear scaling, and
• Scaling of signals for continuous unit conversion.
Completing the first stage, a scaling module is placed after the import data module,
and specified as an “Offset Adjust” module. This will allow the user to “zero” the signal
105
prior to acquisition. The module is expanded appropriately, re-named for clarity, closed
and connected to the import data module. Refer to Figure 3.5.11 for locations of
connection wires. It is important to note that the offset adjust module cannot operate
without a control switch. Separate switch and action modules are placed on the
worksheet and connected to each other. Figure 3.5.10 illustrates these control modules
while Figure 3.5.11 indicates their connection wires. To properly configure the switch,
the module is opened by left double-clicking and defined as a “One Shot Switch.” This
type of switch allows the user to instantaneously activate a predefined action. After the
event is complete, the signal returns to normal operation and does not necessarily remain
equal to zero. Additionally, the labels and configuration of the switch “button” may be
modified to the users liking by changing the labels in the “Text” section of the dialog
box. Figure 3.5.12 illustrates the switch module dialog box.
Figure 3.5.11 – Offset adjust modules and digital meter in black box.
106
Selection of One
Shot Switch
Define button labels
Figure 3.5.12 – Specification of the Switch module operation.
Once the switch is configured, it is ready to operate on the action module (recall
the connections from Figure 3.5.11). The action module requires user input to indicate
the module acted upon and in the manner it will act. For purposes of this worksheet, it is
desired to set the signal value passing through the offset adjust module to zero. Figure
3.5.13 illustrates the action module dialog box, which is accessed by left double-clicking
on the action module. Once the switch and action modules are configured, they are able
to instantaneously zero the offset adjust scaling modules signal at the user’s discretion.
107
Selection of Offset
Adjust module
Define the start
value as Zero
Figure 3.5.13 – Specification of the Action module operation.
Once the offset adjust modules are located, a digital meter is placed on the
worksheet to provide a visual display of the signal. It is important to note the location of
the meter in Figure 3.5.10-11, as connecting it prior to the offset adjust modules will omit
the effect that the zero switch has on the signal. The digital meter’s units do not have to
be established, as the default unit is volts and defined by the ADC. The characters used
by DASYLab to display units utilized by previous modules is “#0”. However, if the user
elects to modify the units of the signal at any module, any word or abbreviation may be
used. For example, “uStrain” will be input after converting the signal to microstrain later
in this example. Additionally, the inputs of the digital meter must be manually copied to
the outputs. This provides an output signal for additional modules to connect with,
passing the signal after the current modules operation to the outputs. A screen shot of the
digital meter’s dialog box can be seen in Figure 3.5.14.
108
Module Name
Copy Inputs
Unit Definition
Figure 3.5.14 – Specification of the Digital Meter module operation.
3.5.5 - Establishment of Calibration Modules
To this point, the worksheet outlined previously is capable of obtaining voltage
signals from two ADCs, filtering them with a predefined low-pass filter, transmitting the
signals into a sub-worksheet (termed a black box) and equating the signal to zero at the
users discretion. In order to make tangible sense of the signals, they must be converted
into a unit of measurement. To maintain accuracy of this unit conversion, a calibration
procedure must be carried out. Calibration of the signals for this worksheet is discussed
below.
As quarter bridge strain gages are to be used, shunt calibration of each sensor may
be used to simulate a strain in each gage (details of shunt calibration may be found in
section 3.2). This simulated strain value may be used to define an additional point for
each individual gage. Using this simulated strain value and a zero point (gained by the
offset adjust module discussed prior) a linear relationship describing each strain gage’s
109
behavior relative to voltage change can be defined. Figure 3.5.15 illustrates the linear
strain-voltage relationship. It is important to note that individual shunt resistors must be
installed on independent channels for this process. When the shunt resistors are activated
each individual strain gage channel will respond differently, as no two resistors are
exactly alike. Thus, prior calculation of the simulated strain is required.
Figure 3.5.15 – Linear scaling from shunt calibration.
In order to accomplish this shunt calibration procedure, a second scaling module
is required for the black box. However, instead of specifying an offset adjust module as
before, this new scaling module requires specification of a “Linear Scaling/Unit
Conversion” module. This module is located to the right, or after, the previous modules
and is depicted in Figure 3.5.16. Once located on the black box worksheet, left double-
clicking on the module opens the scaling dialog box, allowing the user to specify the
required number of channels.
110
Linear Scaling/Unit
Conversion Module
Figure 3.5.16 – Locating the Linear Scaling/Unit Conversion module on the black box worksheet.
As each strain gage will respond to shunt calibration in a unique manner, the
following procedure is used to obtain calibration values. The signals are zeroed by the
offset adjust modules outlined previously. The shunt resistors are activated, producing a
simulated strain. The shunted output voltages of each signal are recorded as global
variables. These variables are then accessed by the linear scaling module, which creates
the two-point scaling illustrated in Figure 3.5.15. The shunt resistors are then
deactivated, returning the signals to their original state. This process is outlined
graphically in Figure 3.5.17.
111
Control switch
When the switch is activated,
The signal is passed to the
Global Variable set module…
…and recorded as a
Global Variable…
…which establishes
the linear scaling of
the signal.
Figure 3.5.17 – Flow chart depicting the signal path while acquiring simulated strain voltages from
shunt calibration. These values are recorded as global variables and then read by the scaling module
to produce a linear strain-voltage relationship.
Unlike the filtering process where a single global variable was set manually, this
process involves the active definition of individual global variables, each specific to their
channel. To store each individual global variable, new modules must be located on the
black box worksheet. These modules are illustrated in Figures 3.5.16 and 3.5.17. First a
relay module with a control input is placed on the worksheet and expanded appropriately.
The relay module sends a single signal value through for each channel; in this application
a single voltage is allowed through. Each of the four channels are spliced between the
digital meter and the new scaling module and connected to the relay. A new “one-shot
112
switch” is placed on the black box worksheet and connected to the relay. This switch
provides a trigger that activates the relay. A Global Variable Set module is then placed
after the relay and expanded to the appropriate number of channels. When actuated by
the switch, the relay passes the present signal values to the global variable set module,
which stores the values as predetermined global variables. The user must define
independent global variables for each channel, which are accessed in the Options menu.
Figure 3.5.6 illustrates the global variables menu. Figure 3.5.18 shows the dialogue box
for global variable set module. Note that individual global variables must be defined by
right clicking over the Global Variable box. The coding used by DASYLab for global
variables consists of $(…) where the ellipsis is a place holder for the global variables
name. In Figure 3.5.18 the global variable used is “STRAIN_CH0”. Subsequent global
variables used in this example were identified as STRAIN_CH1, STRAIN_CH2 and
STRAIN_CH3.
Figure 3.5.18 – Storing global variables for calibration.
113
3.5.6 - Continuous Unit Conversion
As noted before, global variables are recalled by the linear scaling module, which
develops a linear relationship, converting the input signal into a strain value based on
shunt calibration. To establish this relationship, global variables must be acknowledged
by the scaling module, similar to the way the Global Variable #1 = 2 Hz was for the
filtering module. Left double-clicking can open the dialogue box for the linear scaling
module, which is illustrated in Figure 3.5.19. This screen shot illustrates the linear
scaling module’s dialog box where global variables can be recalled from storage by right
clicking over the x2 region. Additionally, individual simulated strain magnitudes from
shunt calibration must be input to the y1 region noted in Figure 3.5.19. These two inputs
define the “Simulated Strain” point from Figure 3.5.15. The lower point, referred to at
the “Zero Point” by Figure 3.5.15, is defined by [x1,y1] = [0,0] in the linear scaling
module. Additionally, as the linear scaling process converts the signal’s voltage to a
simulated strain value, the units of the signal may be modified from this module onward.
Note that Figure 3.5.19 indicates the location for defining a new unit. Figure 3.5.20
illustrates the overall black box worksheet completed for linear scaling of each individual
signal.
114
Figure 3.5.19 – Setting linear scaling values for individual strain gages.
Figure 3.5.20 – Signal path of completed black box worksheet for linear scaling.
115
Once the linear scaling modules are placed on the black box worksheet, an
additional digital meter is installed to observe the scaled strain values and an Export
module is placed to output values back to the main worksheet. The export module
conveys the now converted signals back to the main worksheet.
3.5.7 - Duplicating the Black Box for use with Transducers
The black box must be saved to duplicate it for use with the DBK65 unit. To do
so, the user must activate, or enter, the black box worksheet to be saved. Under the Edit
menu, Save As must be selected, and an ID Tag defined for the black box. The box must
then be saved to the hard drive for future access. Figure 3.5.21 illustrates the menus for
saving a black box while Figure 3.5.22 shows the dialog boxes defining an ID Tag, name
and location of the stored black box.
Selection of the Save
As function for
storing the Black Box
Figure 3.5.21 – Saving the active black box for future applications.
116
Define the ID Tag for
the Black Box…
…and then save it for
future access.
Figure 3.5.22 – Flow of dialog boxes while saving a black box for future use.
Once saved, the black box must be exited and re-imported to the main worksheet.
The Load function may be found in the same location as Save As function illustrated in
Figure 3.5.21. The previously stored black box (denoted by the *.dbb file extension)
must be located on the hard drive and imported to the main worksheet. Once the “Open”
button is selected in the Load Black Box dialog box, the module will be automatically
placed on the main worksheet. However, the new black box is identical to the one stored
and must be modified (e.g. appropriate number of channels) for the DBK65 unit.
Additionally and unfortunately, as the newly loaded black box was created within the
same main worksheet, all the module names are now presented in duplicate. The user
must enter the imported black box and modify all the names to avoid conflict. Left
117
double-clicking on individual modules opens them, allowing the user to modify each new
module within the black box. Only module names need to be modified.
3.5.8 - Configuring the Black Box for Use with Different Channels
As the newly loaded black box was configured for four strain gage channels, it
must be further modified to accommodate the DBK65s two separate transducer channels.
Additionally, as the transducers used in strain gage monitoring are often different (e.g. a
load cell and displacement sensor), dissimilar calibration relationships may be present.
Thus, the newly imported black box must be modified to calibrate both of the two
transducer channels independently.
3. Change the module that
the action module operates on.
2. All modules must be
reduced to 2 channels.
1. All modules must be renamed
4. Define new global variables.
5. Redefine the global
variables used by the
linear scaling module
for unit conversion.
Figure 3.5.23 – Modifications of the black box for DBK65 transducer channels. Note that step 6
(below) is not included in the discussion but is depicted in Figure 3.5.24.
118
Performing the modification of the new black box for transducers entails a
number of details which are outlined as follows and are illustrated in Figure 3.5.23
(above):
1. Renaming all modules contained within the new black box to avoid conflicts.
2. Reducing the signal channels from four (for strain gages) to two for each
transducer. Modules may be simply opened and the number of channels
contracted; connection lines do not have to be modified.
3. Changing the module which the offset adjust action module operates upon.
4. Establishment of two new global variables for independent calibration of the
transducer channels.
5. Redefining the global variables and calibration setting of the linear scaling
module for unit conversion.
6. Copying Offset Adjust modules and Shunt Calibration modules within the black
box for use with an additional transducer channel. Figure 3.5.24 illustrates the
final reconfigured black box.
Figure 3.5.23 illustrates the final configuration of the black box module to be used with
the transducers.
119
Figure 3.5.24 – Modified black box for DBK65 transducer channels.
Reconfiguration of the newly imported black box does not modify the behavior of
the signal processing outlined previously. The only significant change involved is the
production of two independent Offset Adjust and Shunt Calibration module series,
denoted by Transducer 1 and Transducer 2 in Figure 3.5.22.
Once both black boxes are configured, an additional switch and relay are used to control
the recording of data. An On/Off Switch is connected to a relay, which conveys the
scaled signals to a Write Data module. Figure 3.5.25 illustrates the signal path from both
of the black boxes to the Write Data module.
120
Switch controls the relay…
…the relay passes the
signals to the Write Data
module…
…which records
data in a specified
location and format
continuously.
Note that all channels
are connected to the
relay.
Black Boxes
Figure 3.5.25 – Signal path from the black boxes to the Write Data module.
Within the write data module, the type of output file and its characteristics can be
defined. Figure 3.5.26 illustrates the write data dialog box.
Figure 3.5.26 – Specifying data recording options.
121
Once the data collection module is configured the worksheet is able to record
experimental data in the specified file format. The fully configured main worksheet is
shown in Figure 3.5.27. Note the individual zero adjustment and calibration buttons for
the strain gages, transducer 1, and transducer 2 and also the start/stop button for
initializing data recording.
As noted, this worksheet is now adequately prepared for the data acquisition of
strain sensors and transducers. Figure 3.5.27 illustrates the DASYLab main worksheet
for monitoring four strain gages configured in a quarter-bridge circuit with individual
shunt resistors. Also, the main worksheet allows for individual operation and calibration
of two separate transducers. Finally, the user can specify when to start and stop the
continuous recording of the data, which is stored in a file format and location of the users
choosing.
122
Figure 3.5.27 – Overview of completed worksheet.
123
Chapter 4 – Development and Testing of a Portable Strain Sensor
4.0 – Introduction
In order to properly monitor the strain response of the De Neveu Creek IBRC
Bridge, selection of a low-cost, highly accurate measuring instrument was required.
From experience gained at Marquette University and also that of other organizations,
electrical resistance gages were selected as the best instruments for measuring short-term
behavior of the structure. However, installation of individual electrical-resistance gages
directly to the structure has a number of drawbacks. Primarily, the labor involved in
properly bonding the gages to a structure is significant. The reliability of field-applied
gages is also questionable. Previous attempts to record strain response of the De Neveu
Creek Bridge testify to this. Additionally, gages installed directly on the structure are not
removable and are vulnerable to environmental degradation and damage from a number
of other sources.
For these reasons, a removable and portable strain sensor was preferred for this
project. After consulting manufacturers of portable strain instrumentation devices within
the industry, it was found that the cost to implement the proposed instrumentation plan
would be prohibitive if pre-manufactured systems were used. As a result, it was decided
that development of a new cost-effective, reliable and removable strain sensor would be
the best option. The following section describes the selection of circuitry and necessary
calibration used for the strain sensors, research conducted toward final selection of the
sensor base material, and a description of the final sensor and its anchorage to the
124
structural component. Further, the laboratory testing and finite element analysis
conducted to evaluate the performance of the final strain sensor configuration chosen is
detailed and the calibration procedure for each individual sensor is presented.
4.1 – Quarter Bridge Circuit Selection
A noted in section 3.2, the quarter bridge configuration of the Wheatstone bridge
can be constructed rapidly and offers an acceptable degree of precision. It was felt that
the additional sensitivity gained by implementation of a half or full bridge circuit did not
justify the increased expense and labor associated with these configurations. For
example, construction of a full bridge circuit requires more sensor material and
installation of three additional strain gages. While the expense of additional strain gages
is directly offset by the elimination of completion resistors used in a quarter bridge
circuit, the installation of the additional gages incorporates added labor. This stems from
the fact that installation of circuit completion resistors is quite simple relative to the
installation of four gages. Bonding of multiple strain gages in a constrained region
becomes increasingly difficult and leaves significantly less room for error. Thus, both
labor cost and time increases with full and half bridge circuits. If sources of error and
signal conditioning are appropriately addressed, the quarter bridge configuration can
provide satisfactory measurements at a low cost. Using this rationale, the quarter bridge
configuration was selected for the new strain sensor.
To reduce any error sources due to temperature fluctuations, a three-wire
configuration was employed for all gages. Relatively short lead wires were used in
125
laboratory testing (all wires less than 30’) to reduce any desensitization that may be
present with long wire leads. Also, strain levels produced in all gages utilized only a
small portion of the available range, effectively limiting any non-linear effects.
The strain gages selected were Micro-Measurements CEA-06-250UN-350. These
350-ohm gages offer an increased electrical sensitivity over conventional 120-ohm gages.
Also, a thin coating is installed over the foil resistive array by the manufacturer, adding
increased protection. It is important to note that all strain gages were bonded according
to the procedures outlined by the manufacturer. All gages used for this project were
bonded to their substrate with Micro-Measurements M-Bond 200 Adhesive. Each quarter
bridge circuit used in the development of the sensors is illustrated in Figure 4.1.1.
All data acquisition equipment used was manufactured by IOTech and consisted
of a DaqBook 2000 series analog-to-digital converter, a DBK43A strain gage module and
a DBK65 transducer module. The DBK65 was used exclusively for load and
displacement monitoring and provided an excitation of 10 volts to the transducers.
Excitation provided by the DBK43A strain gage module was approximately 2.50 volts to
all channels with rationale discussed later. All data was captured at a sampling rate of 1
kHz, which is assumed to be much greater than twice any expected frequencies to be
encountered. Wheatstone bridges are intended to be direct current circuits and do not
contain oscillating frequencies. This high data acquisition rate also allows the user to
capture sudden changes in instrument response. However, a rapid sampling rate also
creates enormous amounts of data. Care must be taken to ensure that the space available
126
for data storage during testing is adequate. A worksheet was constructed in DASYLab
similar to that found in section 3.5, which was used to simultaneously record strain, load
and deflection of all the instruments used during sensor development.
Vexec
RE
RB
RSENSOR
RA
Rshunt
Vo
+
-
Figure 4.1.1 – Quarter bridge circuit used during laboratory experimentation with the DaqBook
2000 system. Note that nomenclature established by the manufacturer is maintained.
Referring to section 3.2, it can be seen that this circuit simulates a tensile strain
when shunted. Resistive completion of this circuit is established by use of three precision
resistors. Each resistor has a value of 350 ohms, ±0.1%, and are referred to as Rn00A,
Rn00B and Rn00E (IOTech 2005). The completion resistors were manually soldiered
into a removable “plug” provided by the manufacturer. Figure 4.1.2 shows the DBK43A
module as used for all laboratory testing. A shunt resistor was installed in each plug for
shunt calibration. Recall equation 3.2.5, which describes the shunt resistance relationship
and may be rearranged to produce the following expression for direct calculation of
simulated strain.
( )
1 gage
simulated
shunt gageshunt gage
gage
R
GF R RR RGF
R
ε = = • ++
•
(4.1.1)
127
To ensure accuracy of calibration, the resistance of each individual shunt resistor
was measured with a multimeter. Additionally, the resistance of each sensor and lead
wires was measured. Using these values, the proper tensile strain simulation was
manually calculated and input into the scaling module of the DASYLab worksheet. This
process was repeated for every individual strain sensor and strain gage used. For
example, during laboratory experimentation 64.9 k-ohm resistors were used for shunt
calibration. Using equation 4.1.1 we observe the following for a 350-ohm strain gage
with a gage factor equal to 2.105,
( )
350
2.105(64,900 350)
gage
simulated
shunt gage
R
GF R Rε = = =
+• +2,548µε (4.1.2)
120Ω resistors:Channels 3 & 4
350Ω resistors:Channels 1 & 2
Figure 4.1.2 – Completion resistor plug installed in the DBK43A module with top cover removed.
Note that channels 1-4 are occupied and thus have resistors installed.
4.2 – Material Experimentation and Selection
A number of materials were evaluated before final selection for the strain sensor.
To achieve the objective of developing a removable and portable strain sensor, it was
128
decided that the quarter bridge strain gage needed to be bonded to a suitable carrier
material. This carrier would then be bolted to the structural component, transmitting any
strain to the carrier then the strain gage. A wide array of materials for embedded and
externally mounted sensors are available, however, they are most often polymer
composites and low modulus metals. Figure 4.2.1 shows an example of a nylon sensor to
be embedded in asphalt or concrete.
Figure 4.2.1 – Strain sensor with quarter bridge strain gage composed of nylon.
Experimentation was carried out with sensors composed of carbon-fiber
composite. The carbon fiber sensors were machined to accept a single strain gage
centered on the sensor and are illustrated in Figure 4.2.2.
Brownie installed on
bottom on concrete slab
(a)
(b)
Figure 4.2.2 – Carbon-fiber strain sensor with quarter bridge strain gage (a) and installation (b).
129
These sensors were then installed on the top and bottom of an instrumented
concrete slab and bonded using an epoxy recommended by the carbon-fiber manufacturer
(Figure 4.2.2(b)). It was observed that the strain levels produced by the carbon-fiber
strain sensor differed greatly when compared to those produced by a complementary gage
bonded directly to the slab (Figure 4.2.3).
70 80 90 100 110 120
0
50
100
150
200
250
300
350
400
450
uStrain
Time (seconds)
Carbon-Fiber Gage
Bare Gage
Figure 4.2.3 – Recorded strain levels in carbon-fiber strain sensor and bonded strain gage.
The discrepancy in strain readings can be attributed to the fact that the carbon-
fiber sensor has a significantly higher stiffness relative to that of the concrete substrate.
Typical values of material modulus may be found in Table 4.2.1.
Material Modulus of Elasticity (ksi)
Carbon Fiber (fiber only) 33,500
Steel 29,000 - 30,000
Carbon Fiber Composite 22,500
Aluminum 10,000 - 11,000
Concrete 2,500 - 4,500
Nylon 300 - 500
Tyfo S - Epoxy 461
Table 4.2.1 – Typical modulus of elasticity values of materials (Fyfe 2005; Gere 2001).
130
As the concrete fibers stretch or compress, strain is transferred through the epoxy layer.
Since the modulus of epoxy is much lower than that of the carbon-fiber plate, a large
amount of strain is absorbed by the epoxy layer. Thus, the true strain is never transferred
to the carbon-fiber plate and consequently the strain gage.
Stiffness differences between the measured substrate and sensor material can
affect the measured strains. Farhey (2005) reported that that the presence of a sensor
with greater stiffness than the measured substrate will disturb its natural response. As a
result of these findings, a lower modulus material was required for the sensor. For this
project the target substrate is composed of concrete and FRP materials and therefore the
modulus of the strain gage carrier should be compatible with these materials.
Furthermore, research of bonding materials for sensor attachment was conducted.
It was found that current epoxy and other commercially available adhesives are not
acceptable for bonding strain sensors. The elastic modulus of traditional epoxies is very
low causing the epoxy-adhesive layer to stretch significantly, thus lowered strain levels
are expected in the sensor. Based on this, a mechanical anchorage system is required for
attachment of strain sensors, with a carrier that has an appropriately low modulus of
elasticity.
4.3 – Description of Portable Strain Sensor
Based on the preliminary research conducted, a prototype sensor constructed of
series 6/6 Nylon was manufactured by ROMUS, Incorporated of Milwaukee, WI
131
(ROMUS 2005). Its low modulus (approximately 400,000 psi) and relatively low cost
was ideal for both performance and mass-production of sensors. The material is also
easily machined allowing for detailed designs to be translated into prototypes. The
original prototype was a rectangular bar 1.00” wide by 4.00” long with a thickness of
0.25.” Figure 4.3.1 illustrates the final geometry of the prototype while Figure 4.3.2
shows completed strain sensors without their protective external coating or electrical
connector tabs. These items are discussed further below.
Two 0.386 in. diameter holes were located 0.50” from each end centered on the
width of the sensor carrier, allowing for mechanical anchorage via epoxy-adhered
threaded studs. These holes define the effective gage length of the sensor to be 3.00.”
Additionally, a central depression 0.50” wide by 1.50” long was machined 0.20” into the
sensor. A secondary depression 0.20” deep and 0.25” wide was machined into a single
end of the main depression to allow for strain relief of the lead wires.
4.00”
1.00”
0.50”
Strain Gage
0.50”
1.50”
0.25”Depression for strain
relief of wires
Oversized Bolt Holes
Figure 4.3.1 – Final configuration of the strain sensor.
132
Figure 4.3.2 – Constructed strain sensors without connection tabs or protective coating.
Strain relief is achieved by bending the lead wires into the depression and
anchoring them with a quickset epoxy. These depressions allow for the strain gage,
necessary soldering and lead wire adhesive to be below the surface of the sensor,
reducing the risk of accidental damage to the gage. Further geometric detail is provided
in Appendix C.
As the strain sensors are to be installed on the De Neveu Creek Bridge,
environmental protection, rapid connection methods and the ability to remove the gages
at the end of the test are required (sensors will be used for two WisDOT bridges). To
attain a satisfactory level of environmental protection, the central depression each sensor
is filled with a rubber-like compound, M-Coat J, manufactured by Micro-Measurements.
This material a two-part polysulfide liquid polymer that completely seals the gage
(Micro-Measurements 2004). The polymer is relatively soft and will not affect the strain
133
response of the sensors. Care was taken to isolate the exposed lead wires and gage from
the M-Coat with a Teflon-adhesive tape provided by Micro-Measurements. Additionally,
to ensure rapid deployment of each sensor, individual lead wires exiting the strain sensor
contain an individual, insulated quick-disconnect tab. These connections can be made
quickly and repetitively without an appreciable amount of electrical resistance. Male tabs
were soldiered to the lead wires on the sensor to ensure a durable connection, while the
female tabs will be installed on the lead wires of the bridge by crimping.
4.4 –Anchorage of the Sensor
As noted in section 4.2, a mechanical anchorage system is required for installation
of strain sensors. A simple but effective system is proposed as follows. Mechanical
anchorage for each sensor is to be provided by two 1/4” diameter, 3” long bolts with
standard plain washers on each face of the sensor. Each bolt is to be A307 steel. An
appropriate size nut, torqued to 120 lb-in, confines the washers and sensor. Deformed
washers, also called star washers, are not recommended, as they will significantly scar
and deform the nylon when tightened. Since the De Neveu Creek Bridge is composed
of concrete, each bolt is to be set in a 5/16” diameter hole and adhered with a high-
strength construction epoxy. Each bolt is to be set 1” into the substrate. All anchorage
components are to be manufactured by Powers Fasteners.
Figure 4.4.1 depicts a typical field installation. Transfer of load is accomplished
by friction between the substrate, washers and nylon, and does not rely on bearing of
bolts. Each attachment hole on the sensor is oversized for two primary reasons. The
134
over-sizing of each hole eliminates the possibility of the bolts bearing directly on the
nylon. Through laboratory testing and numerical modeling it was found that bolt bearing
causes significant local deformations, ovalizing the hole and disrupting strain distribution
through the sensor. Figure 4.4.2 illustrates this effect. Additionally, use of slightly
oversized holes allows for reasonable out-of-plumb tolerances for the field installation of
the threaded studs.
Strain SensorBolt
w/nut
Standard Washers
Drilled hole w/Bolt
set in adhesive
1”
Figure 4.4.1 – Field installation of the strain sensor to concrete.
Bolt
Unloaded hole
Deformed hole under load
Figure 4.4.2 – Ovalization of a bolt hole under loading.
Tests were conducted to evaluate the mechanical anchorage system described
above. Further, a finite element model was developed to provide a comparison to the
data observed. The following two sections outline laboratory tests evaluating the
performance of the sensor and the anchorage system.
135
4.5 – Laboratory Validation
To provide a consistent venue for evaluating the performance of sensors, a
constant-moment bending test was developed. This configuration produces a constant
curvature over a user-controlled length of the beam thus providing a constant strain at any
fiber along the entire length of the constant moment section. Figure 4.5.1 shows the test
frame and beam configuration used while Figure 4.5.2 provides further detail.
Figure 4.5.1 – Four-point bending test used for strain sensor evaluation. The data acquisition system
can be seen in the background, behind the test frame.
8’- 0”
3’- 0”2’- 6”
Load
Load Cell
W8x31
W6x20
1’- 6”
Figure 4.5.2 – Dimensioned constant-moment beam testing schematic.
136
The primary bending member was a W6x20 shape, approximately 9’ long, bent
about its minor axis. Minor-axis bending was utilized to eliminate any lateral-torsional
buckling/instability effects when subjecting a segment of the beam to pure bending.
It is interesting to note that one end of the member had been cleanly sawn, while
the other had been cut by an acetylene torch, albeit very cleanly. Roller supports for the
W6 beam were located at 8’-0” with a 6” overhang on each end. Atop the primary beam
was a W8x31 spreader beam 4’-0” long, loaded about its major axis. Roller supports
were located 6” in from each end and centered on the primary beam. As a side note, a 5”
long by 2” deep section of the W8 had been previously removed for material testing. It is
assumed that this removed section had no effect on the distribution of loading during all
tests. Based on the material testing conducted and additional information of the
suppliers, both beams are composed of Grade 50 steel and are expected to maintain a
yield stress of 50yF ksi= .
Load was applied by a hand-actuated hydraulic ram, which was monitored by a
calibrated electronic load cell. Mid-span deflections of the primary beam were monitored
throughout testing. A linear displacement sensor (LDS) and a dial gage were located on
the beam for verification of displacements. The LDS monitored the displacement of the
beam web, 4’ from each support and at mid-span of the W6. Spatial constraints forced
locating the dial gage 4’ from each support but on the bottom exterior flange of the
primary beam. Both the load cell and the LDS were connected to the DBK65 transducer
module for real-time data acquisition synchronized with the strain readings.
137
For laboratory evaluation, two sets of holes, 21/64” in diameter, were machined
into a single flange of the W6 beam. Each set of holes was offset vertically 1.76” from
the centerline of the web and centered at the mid-span of the beam as shown in Figure
4.5.3. The holes were set at a gage of 3”. Each sensor was attached with two Grade 8
5/16” diameter bolts. The tightening nuts were then gradually torqued in an alternating
fashion to 120 lb-in using a calibrated torque wrench. Special care was given to sensor
location when tightening the nuts. If during the tightening process the sensor moved
from its intended location, the nuts would be loosened and re-tightened with the sensor in
its appropriate location. This was done to ensure that the sensors were oriented parallel
to the flanges of the test beam at the target 1.76” locations.
Complementing these holes for strain sensor attachment were standard strain
gages, bonded directly to the beam on the opposite flange and centered in the same
locations (Figure 4.5.3). Idealizing the W6 as a perfect beam, engineering mechanics
requires that these gages “feel” identical strain as the sensor they are complementing.
This produces a tensile/ compressive pair of readings, each with a bonded gage
complementing a strain sensor for a total of four strain channels.
138
Standard
Strain Gages
Strain
Sensors
Load equally
distributed to flanges
yb
yt
yt = yb=1.76”
Bolt Holes
Figure 4.5.3 – Mid-span layout of Strain sensors and complementary strain gages.
It is of significant note that the strain gages directly bonded to the main test beam
were Micro-Measurements EA-06-250UN-120. The gages differed from those used in
the sensors as they were only 120 ohms and did not have any protective coating. These
gages were used as they have proven to be very effective in strain measurement in the
laboratory. Also, 120-ohm completion resistors were implemented in the DBK43A for
these channels in lieu of the 350-ohm completion plugs used for the strain sensors.
However, the circuit configuration and shunt calibration process were the same. Figure
4.5.4 illustrates two strain sensors installed while Figure 4.5.5 shows the two bare gages
used for comparison values.
139
3”
Figure 4.5.4 – Strain sensors installed for the constant-moment beam test.
Top and Bottom strain
gages used for comparison
with Strain sensors
Figure 4.5.5 – Complementary strain gages installed on the opposite flange as Strain sensors for the
constant-moment beam test.
140
From the discussion noted in section 3.3, heating of the strain gage in absence of
an adequate heat sink will produce errors in measurements. The nylon material used for
the strain sensors may be classified as a poor heat sink and requires a low level of voltage
excitation (Micro-Measurements 2005). Calculations found in section 3.3 (Eqns. 3.3.2 -
3.3.4) are representative of this material and gage geometry and thus may be used for the
strain sensors. For this reason all excitation levels, including those of the bonded strain
gages, were set at approximately 2.5 volts. Those gages bonded directly to steel do have
an adequate heat sink available, but excitation was set at similar levels to maintain
consistency.
4.5.1 - Torque Level Tests
To evaluate the load imposed on the sensor when tightening the fastening bolts
(threaded stud pretension), an experiment evaluating torque levels on each individual
sensor’s mounting bolts was carried out. Two strain sensors were installed on the test
W6 beam and tightened to a pretension corresponding to a torque of 120 lb-in. The test
beam was then loaded to 5 kips and strain, load, and deflection data were recorded. The
frame was unloaded and sensors were removed and re-installed with a pretension
corresponding to 180 lb-in torque. The beam was loaded again to 5 kips. This process
was carried out for three additional pairs of sensors. All specimens were attached to the
beam with a washer only on the outside face of the sensor while the inside face was in
direct contact with the beam. A total of four tests were conducted at the 120 lb-in setting
and four at the 180 lb-in setting.
141
The tensile and compressive values for the sensors and complementary strain gages were
then averaged and compared using the ratio Sensor BareGageε ε . Table 4.5.1 provides a
summary of data recorded during this test.
Instrument Comp Stdev Tension Stdev Comp Tension
Bare Gage -358 2 369 5 - -
120 lb-in Nylon -433 13 396 26 1.21 1.07
180 lb-in Nylon -418 23 396 21 1.17 1.07
Difference = 4% 0%
Results Nylon/Gage Ratio
Table 4.5.1 – Torque level test data. Compression and tensile values
reported are averages of test results.
It was observed that for tensile readings no change occurred. On the other hand,
compressive readings strain sensor values were 4% closer to the bare gage values at the
higher, 180 lb-in setting than the lower torque setting, albeit with greater uncertainty.
Explanation for this behavior will be provided in the finite element analysis section to
follow. While the higher pretension value did return results closer to the bare gage
values, implementation of this pretension in the field would require an embedment length
greater than 1”. This deeper embedment is not recommended as it may penetrate the
prestressing steel of the girders. Additionally, the higher threaded stud pretension setting
tended to significantly deform the soft nylon sensor material, which may lead to long-
term differences in individual sensor response as the instrument is removed and re-
installed. Figure 4.5.6 illustrates this effect.
142
Figure 4.5.6 – Deformed region of washer contact due to tightening the anchorage nuts to 180 lb-in.
4.5.2 - Evaluation of Washer Presence
A test was performed to evaluate the effect that various support conditions had on
the strain sensors. Two conditions were selected for field installation: one with a
standard washer on each surface of the nylon strain sensor, and another with only a
washer on the outside of the sensor only. In the latter case, the sensor is closer to the
substrate being monitored, but is also rigidly supported in compression by the substrate
(finite element analysis presented later will illustrate this). Data for this case was
recorded during the torque level load test. Four pairs of sensors were attached to the test
beam, all with 120 lb-in torque levels but with washers on both nylon surfaces. The
beam was then loaded to 5 kips and data recorded. Data from this test are summarized in
Table 4.5.2.
Condition Comp Stdev Tension Stdev Comp Tension
Bare Gage -362 2 371 2 - -
Nylon w/double washers -419 31 399 23 1.16 1.07
Nylon w/single washer -433 13 396 26 1.20 1.07
Difference = -4% 0%
Results Nylon/Gage Ratio
Table 4.5.2 – Boundary condition test data. Compression and tensile values
reported are averages of test results.
143
It was found that the tensile response of the sensors was nearly identical for each
washer condition. However, when in compression the double washer condition produced
results closer in magnitude to the corresponding tensile case. As having sensors that
behave similarly in tension and compression are desirable, all sensors developed in this
project utilize a washer on all faces of attachment (Figure 4.4.1). Further investigation
into the differences in strain readings is provided in the finite element analysis section to
follow.
4.5.3 - Excitation Voltage Evaluation
Sections 3.3 and 4.5 both contain comments describing the effect that gage
heating can have on measurement. As a precautionary measure, a test was conducted to
evaluate if the excitation voltage level selected for the sensors was in fact appropriate.
Four independent strain sensors were configured in a temperature-compensating half-
bridge circuit and tested using bolt pretensions outlined previously. The half bridge
configuration (Figure 4.5.7) eliminates temperature effects as both sensors experience
equal resistive changes due to any heating. As noted in section 3.2, the output of a
Wheatstone bridge is dependent only upon the ratio of gages on individual sides of the
circuit. The experiments conducted were run for a minimum of 20 minutes to allow long-
term heating to take place in the sensors. Each half bridge circuit contained a sensor
subjected to deformation by the bending test (RSENSOR) while the other sensor (RDummy)
was undisturbed.
144
Vexec
+
-
350ΩΩΩΩ RSENSOR
350ΩΩΩΩ RDummy
Figure 4.5.7 – Half bridge temperature compensating circuit.
All sensors attached to the test beam were tightened to 120 lb-in and were
installed with only a single washer on the outside face of the sensor, even though double
washers are recommended for field implementation. Strain values recorded during this
test were then compared to data recorded from the other tests that were configured in the
standard, quarter bridge circuit that does not compensate for temperature effects.
Overall, no difference was observed between the temperature compensated half bridge
sensors and the standard quarter bridge sensors. Thus, the excitation level used for this
project is valid and is not expected to produce error in strain readings.
4.6 – Finite Element Analysis
To verify the response of the strain sensors from the constant-moment beam test,
a series of finite element models were constructed using the computer program ANSYS
(ANSYS 2005). Both three-dimensional (3D) models of the W6 test beam and the nylon
strain sensor were constructed.
145
4.6.1 - Finite Element Model of Test Beam
First, a FE model of the test beam used was constructed. The material model used
for beam included a modulus of elasticity of 28,500 ksi and a Poisson’s ratio of 0.30.
The modulus of elasticity was back-calculated from observed deflection values of the test
beam and assumed cross-sectional properties. Additionally, these values are similar to
typical values for steel material. The geometry of the beam was modeled using
dimensions for a W6x20 found in the AISC manual (AISC 2001). It should be noted that
the values found in the AISC manual for flange and web thickness or overall depth of
section and flange width were not equal to those measured on the test beam, but were
reasonably similar. That is, when calculating the values for moment of inertia (both
major and minor axes) and the sections area they were found to be essentially equal to
those values published by AISC. Using the manual’s values, these dimensions were
input in a two-dimensional (2D) plane and meshed using PLANE42 elements. These 2D
elements were used solely as an initial step in construction of the three-dimensional (3D)
model. All meshing was mapped to lines by defining the number of elements to be
meshed within a defined area. This method of meshing allows the user to have greater
control on the formation of elements. The method of mapped meshing is illustrated in
Figure 4.6.1.
Mapped Meshing
7 divisions specified
per line7 elements per side
are created
Figure 4.6.1 – Illustration of the mapped meshing procedure used.
146
Once the 2D model of the beam’s cross-section was constructed with an
appropriate arrangement of elements, it was extruded longitudinally, creating the third
dimension of the model. The 3D elements used were of type SOLID95, of which every
element contains 20-nodes has three degrees of freedom (DOF) per node – translation in
the nodal X, Y, and Z directions (Figure 4.6.2). These 20-node “brick” elements were
used throughout the FE model. When completed, the beam model contained 6,798
elements, and 21,320 nodes.
3 DOF: UX, UY, UZ
Z
X
Y
Figure 4.6.2 – 20-node brick element used for 3D modeling.
Boundary conditions of the beam model were provided at individual nodes for
support and loading conditions. Nodes representing the roller supports at beam-ends
were restrained in the vertical (Y) direction. Also, one end of the beam was restrained in
both the horizontal (X) and longitudinal (Z) directions. Figure 4.6.3 illustrates the
boundary conditions imposed on the beam model.
147
UX = UY = UZ = 0UY = 0
PP
8’- 0”
3’- 0”2’- 6”
Figure 4.6.3 – Boundary conditions of the 3D beam model. The magnitude of load, P, is described in
the text.
Loads were also applied directly to the nodes at locations where the W8 spreader
beam contacts the main test beam. Idealized as roller supports, an aggregate load of
5,000 lbf was applied to the twelve nodes contacting the spreader beam. A force of
416.67 lbf was applied to each node in four groups of three nodes, simulating the total
force applied by the hydraulic ram
After the FE model was constructed and configured, a solution was produced.
Maximum vertical deflection was recorded at mid-span with a magnitude of 0.2019 in
downward. This value agrees well with deflections recorded during laboratory testing at
mid-span of the beam, which had a range of 0.19 to 0.20 in downward.
148
From the FE beam solution, strains at the level corresponding to the location of
the bonded gages on the test beam were ±350 µ. Positive values are defined as tensile
strains and were located at the bottom of the beam, similar to those strains observed in
testing. It is noted that the strains observed were at ±1.75” from the center of web, while
the strain gages bonded to the test beam were at ±1.76” from center of web. It is felt that
this small difference does not provide reason for concern.
To validate the results of the FE model were computation from beam theory. The
same geometry and loading conditions as the FEM beam model (Figure 4.6.3), and the
same modulus of 28,500 ksi were utilized. Cross-section measurements of the actual
W6x20 test beam were made in the laboratory, yielding a minor axis moment of inertia
equal to 13.387 in4. The fillets of the test beam were omitted for calculation, as their
effect on the moment of inertia is considerably small. Using a distance from the section
centroid to the location of the bonded gages equal to 1.76”, strain at the location of the of
the bonded strain gages was calculated to be ±346 µ. This minute difference between
theoretical calculations and the FE solution indicates that the model is appropriate for this
analysis.
For comparison, strain values recorded by gages bonded directly to the beam in
the laboratory testing had a range of –364 (compression) to 380 µ (tension), which
correspond to a difference of 14 and 20 µ, respectively relative to the results of the beam
model. Overall, the results from the laboratory, theoretical calculations and the FE model
are very close. It was felt that both the strain and deflection values were similar enough
149
to not warrant any further consideration and validated that the strain gages bonded to the
steel test beam were adequately shunt calibrated and working properly.
4.6.2 - Finite Element Model of Strain Sensor
In order to better understand the behavior of the strain sensor when strained, a
model of the strain sensor was developed. The strain sensors behavior under different
support conditions (washer presence tests, section 4.5.2) and under varying pretensions
(torque level tests, section 4.5.1) was not made clear during laboratory testing. It was of
great importance that a FE model of the sensor be created, providing an alternative venue
for comparison and evaluation. As the geometry of the sensor is asymmetrical, a detailed
FEM was created in a similar manner as the beam model. However, multiple iterations
of modeling were made in attempts to construct the most accurate model.
Acknowledging that strain values reported by the FE model would not exactly match the
values observed from strain gages on the test beam, and also the difficulty in recreating
identical boundary conditions for the sensor, it was decided that the accuracy of the
model would be based upon a comparison of actual values (the actual readings from
bonded strain gages) and FE model values. Boundary conditions would be varied in a
realistic manner until the results produced by the FE model “enveloped” the actual values
observed on the beam. Furthermore, it was expected that strain values for tension and
compression would be equal to each other for the double washer anchorage system
recommended in section 4.5.2. The modeling process is described below.
150
The material model used for modeling the strain sensor included a modulus of
elasticity of 400 ksi and a Poisson’s ratio of 0.38. These properties were chosen, as they
are common values for the sensor’s base material, Nylon 6/6. For example, the
magnitude of the modulus value was identified as the mean value in wide array of values
for Nylon (Table 4.2.1). Initially, a 2D model of the strain sensor was created using
PLANAR82 elements and mapped meshing. All geometric details to be encountered
within the sensor were incorporated into this 2D model. This was done so that extrusion
of areas could be performed in stages, replicating the geometry of the sensor. An
illustration of the extrusion process is given in Figure 4.6.4. For example, circular lines
for the bolt holes were constructed in the 2D environment. When the planar model was
extruded “upward,” giving the model a defined thickness, the circular lines form a
cylinder that define the boundary of the bolt hole. As with the beam model, all 3D
elements were SOLID95 elements, composed of 20-nodes and of brick shape (Figure
4.6.2). The final sensor model contained 2,164 elements and 9,397 nodes.
(a) (b) (c)
0.00 in0.05 in
0.25 in2D Planar
mesh
Figure 4.6.4 – The extrusion process uses to build a 3D model of the sensor. It can be seen that from
figure (a) the entire 2D planar mesh is extruded 0.05” in figure (b). The center depression is then
created in figure (c) by extruding all areas around the depression.
151
The boundary conditions of the sensor model varied greatly as it is difficult to
simulate the actual loading of the sensor through the washers and threaded studs. Recall
that all load transfer is to be achieved by the friction between nylon and washer; the
magnitude of such a friction force is challenging to reproduce. In lieu of applying loads
to the sensor model, it was decided that applying a prescribed longitudinal displacement
to the sensor model would accurately simulate the beam test.
A single end would be displaced while the other would be restrained from
displacement. This displacement represents the displacement of the bolts anchored in the
test beam and was calculated using a strain of ±370 µ, which is an approximate
midpoint for the strains experienced by the strain gages bonded to the test beam during
laboratory testing. The following calculation provides explanation to the imposed FE
model displacement of ±0.00111 in.
( )( ) ( )( )63.0 370 10 0.00111Longitudinal AppliedGageLength in inε −∆ = = ± • = ± (4.6.1)
By displacing the nodes in the FE model of the sensor Longitudinal∆ the model could
simulate the sensor deformation seen in the laboratory tests. However, how to apply this
displacement was not originally clear. It was decided that creating a suite of various
boundary conditions could “envelope” the true behavior of the sensor, providing a venue
for comparison. Further, these variations in boundary conditions could help explain the
results seen during the testing done to evaluate the presence of washers on the sensor
(section 4.5.2) and the results of the torque level tests (section 4.6.1).
152
To envelope the proper boundary conditions of the FE model of the sensor, a
number of trials were conducted focusing on evaluating two primary situations. First, the
regions affected by bolt hole displacement were addressed. By systematically adjusting
the boundary conditions around the bolt holes, an accurate simulation of the contact each
washer has on the sensor was developed. Additionally, the interaction between the
sensor and the steel beam was addressed. Manipulation of the boundary conditions on
the surface between the sensor and the steel beam were varied to study the presence
washers have on the behavior of the sensor. The condition where no washers were
present between the steel beam and the sensor was evaluated, as well as the condition
where they were separated by a washer. Of particular note is the scenario illustrated in
Figure 4.6.5.
Sensor material
penetrating the steel beam
Figure 4.6.5 – Inadequately restrained model penetrating the steel test beam while subjected to
compression.
It was observed that when loaded, the sensor has a tendency to deform either
toward or away from the steel beam. In the case where no washers are present between
the steel beam and sensor (models 1-3 below), compression will cause the central region
of the sensor to deform into the beam, which is not possible. Additionally, when
subjected to tension, the opposite occurs. The central region of the sensor model deform
153
away from the beam while the outer edges of the model deform into the beam. Thus
appropriate boundary conditions are required that prevent this type of impossible
deformation.
Additionally, it was observed through experimentation with the sensor model that
when the bolt hole regions were subjected to boundary conditions indicative of a large
bolt pretension, specifically the higher 180 lb-in pretension imposed on the threaded stud
in section 4.5.1, the compressive response of the sensor model would become more
similar to the simulated strain of -370µε. It is theorized that these more stringent
boundary conditions produce a more efficient channeling of strain through the sensor
model by providing a greater degree of longitudinal restraint. It was recognized that the
lower pretension value had been selected for reasons outlined in section 4.5.1, and the
imposed during the iterations of modeling were cognizant of this.
Overall, six iterations of the sensor model were developed and are described
below. A table of figure listings is provided in Table 4.6.1 for clarity.
Comp. Tension
1 Figures 4.6.6/7 Single -370 278 1.33
2 Figures 4.6.8/9 Single -378 389 0.97
3 Figures 4.6.10-12 Single -403 413 0.98
4 Figures 4.6.13/14 Double -404 404 1.00
5 Figures 4.6.6/15 Double -404 404 1.00
6 Figures 4.6.6/15 Double -404 404 1.00
Comp/Tension
Ratio
uStrainBoundary
Conditions
Model
Number
Washer
Condition
Table 4.6.1 – Boundary Conditions used for the FE model of the sensor.
154
Strain Sensor
Stationary Bolt Single Washer
UX = UY = UZ = 0 UY = +0.00111in.
X
Y
Z
Y UZ = 0 UZ = 0
Displaced Bolt
Steel Flange
Figure 4.6.6 – Boundary conditions for the tensile case of the sensor model 1.
UX = UY = UZ = 0 UY = -0.00111in.
X
Y
Z
Y UZ = 0 UZ = 0
Figure 4.6.7 – Boundary conditions for the compression case of sensor model 1.
Strain Sensor
Stationary Bolt Single Washer
UX = UY = UZ = 0 UY = +0.00111in.
X
Y
Z
Y UZ = 0 UZ = 0
Displaced Bolt
Steel Flange
Figure 4.6.8 – Boundary conditions for the tensile case of sensor model 2.
UX = UY = UZ = 0 UY = -0.00111in.
X
Y
Z
Y UZ = 0 UZ = 0
Figure 4.6.9 – Boundary conditions for the compression case of sensor model 2.
155
Rings around bolt holes to simulate
the presence of washers
Figure 4.6.10 – Ring of elements around bolt holes extruded through thickness of sensor for sensor
model 3.
Strain Sensor
Stationary Bolt Single Washer
UX = UY = UZ = 0 UY = +0.00111in.
X
Y
Z
Y UZ = 0 UZ = 0
Displaced Bolt
Steel Flange
Boundary conditions imposed on
entire cylinder around bolt hole
Figure 4.6.11 – Boundary conditions for the tensile case of sensor model 3.
X
Y
Z
Y UZ = 0 UZ = 0
UX = UY = UZ = 0 UY = +0.00111in.
Boundary conditions imposed on
entire cylinder around bolt hole
Figure 4.6.12 – Boundary conditions for the compression case of sensor model 3.
156
Strain Sensor
Stationary Bolt Double Washers
UX = UY = UZ = 0 UY = ±0.00111in.
X
Y
Z
Y
UZ = 0
Displaced Bolt
Steel Flange
Only areas contacting the washer
receive boundary conditions indicated
UX = UY = UZ = 0
UY = ±0.00111Figure 4.6.14
Figure 4.6.13 – Boundary conditions for both compression and tensile cases of sensor model 4. Note
the incorporation of Double washers at each bolt.
Figure 4.6.14 – Detail of boundary conditions imposed to simulate contact with a washer for sensor
model 4. The restrained bolt hole is depicted in the figure.
157
Strain Sensor
Stationary Bolt Double Washers
UX = UY = Uz = 0 UY = ±0.00111in.
X
Y
Z
Y UZ = 0
Displaced Bolt
Steel Flange
Only areas contacting the washer
receive boundary conditions
UY = ±0.00111UX = UY = Uz = 0
Figure 4.6.15 – Boundary conditions for both compression and tensile cases of sensor models 5 and 6.
Model 6 incorporated geometric changes only.
Sensor model 1 was the first trial in modeling the strain sensor. This model
incorporated boundary conditions preventing translation of the sensor into the steel beam,
simulating the condition where no washer exists between the sensor and beam. That is,
the sensor was not allowed to translate into (or away from) the Z-axis as indicated in
Figures 4.6.6-7. The prescribed displacement was applied to half the nodes on the
perimeter of the displaced bolt hole, at both top and bottom surfaces. Elements within
the depth of the bolt hole were did not receive boundary conditions (similar to the
boundary conditions depicted in Figure 4.6.14). Out-of-plane displacement was not
restrained at the displaced bolt hole except where indicated in Figures 4.6.6-7. Also, the
restrained bolt hole (all DOF=0) had boundary conditions imposed at nodes on half the
perimeter of such hole at both top and bottom surfaces. This model resulted in
compressive and tensile strains of -370 and 278 µε, respectively, which produces a
158
compressive-to-tensile (C/T) ratio of 1.33. As these values are significantly different,
modifications were warranted.
Sensor model 2 was similar to number 1, however, the entire perimeter of the bolt
holes had boundary conditions imposed on them, at both top and bottom surfaces. These
revisions of the boundary conditions imposed were intended to more accurately simulate
the interaction of the washer around the entire perimeter of the bolt holes. This model
resulted in compressive and tensile strains of -378 and 389 µε, respectively. While these
values were more similar than the previous values, the magnitude of tensile strain was
now greater than compressive strain. As a result the C/T ratio became 0.97, which
indicates more similar performance between tension and compression. However, further
investigation was performed to try and improve the performance of the model.
For sensor model 3, a cylinder of elements was constructed surrounding each bolt
hole with an outer diameter of 0.5” (corresponding to the washer’s outer diameter) and
inner diameter of the bolt hole. All elements within the entire cylinder were displaced the
prescribed amount (Uy only) at one bolt hole and restrained (all DOF=0) at the other bolt
hole. Figure 4.6.10 illustrates the “ring” that was extruded through the thickness of the
sensor model to obtain the cylinder. The boundary conditions at the interface between
the steel beam and sensor were maintained similar to model 1 and 2. Strains produced by
the model’s solutions were -403 µε compression and 413 µε tension with a C/T of 0.98.
As these values increased nearly equally, yet maintained nearly the same C/T ratio, it was
felt that using the entire cylinder of the bolt hole only channeled more strain into the
159
sensor, and did not change how it was distributed in the sensor. Thus, a new set of
boundary conditions were imposed on the model in attempts to attain a similar strain
magnitude in both compression and tension.
Sensor model 4 aimed at modeling a condition where the sensor and steel beam
are separated by a washer, termed “double washers.” The cylinder of elements around
each bolt hole from model 3 was utilized, however, only surface elements received
boundary conditions. For clarity, no elements within the cylinder received boundary
conditions (Figure 4.6..14). At the restrained bolt hole, the ring’s top and bottom
surfaces were restrained in all DOF. At the displaced bolt hole, the ring’s top and bottom
surfaces were displaced the prescribed amount. Additionally, at the bottom surface of the
displaced bolt hole out-of-plane translation (Uz) was restrained. Resulting strains from
this model were ±404 µε. This equality of strain magnitude was expected as the sensor
model was now able to deform freely in either direction. Upon review of the
deformation, the magnitude of out-of-plane deflection was minute (significantly less than
0.01”) and thus was not visible to the eye, or greater than the thickness of the washer.
Sensor model 5 maintained the same boundary conditions as model 4, however,
the out-of-plane translation (Uz) was restrained at all surfaces where washers contact the
sensor (Figure 4.6.15). The same strain magnitudes were produced by the model’s
solution (±404 µε), and were expected since incorporation out-of-plane deformation at
the displaced bolt hole from model 4 had been significantly small.
160
The final model, sensor model 6, incorporated a geometric change to
accommodate the strain relief notch near the central depression where strain gages are to
be bonded. All boundary conditions imposed in model 5 were maintained. Figure 4.6.16
illustrates the notch added for strain relief.
Notch added in
sensor model 6
only
Figure 4.6.16 – Notch for strain relief of wires in sensor.
The same strain magnitudes were produced by the solution for model 6 (±404 µε)
and it is assumed that no degree of further refinement will produce differing values. A
contour plot of elastic strain distribution is provided in Figure 4.6.17.
161
Compression Tension
± 404 µε
Notch for strain
relief of wires
Figure 4.6.17 – Longitudinal strain distribution ( )Yε for tension and compression cases for the final
sensor model.
In addition, the magnitude of strain produced by the final sensor model compares
relatively well to that reported during laboratory testing. In tension, the mean strain value
recorded when using washers on all faces of the sensor was 399 µ. The compression
case observed a mean value of –419 µ (Table 4.5.2). While the tension value is quite
similar to the FEM results, the slightly larger difference for compression is deemed
satisfactory given the complex interaction of the sensor and washers under compression.
A summary of results is provided in Table 4.6.1.
Comp Tension Comp Tension
Bare Gage -362 371 0.97
Nylon w/extra washer -419 399 1.05 1.16 1.07
FE Model #6 -404 404 1.00 1.09 1.09
Difference = 7% -2%
C/T
Ratio
Results Nylon/Gage Ratio
Ratios for the nylon sensor are taken with respect to the bare gage strains
while the FE model ratios are relative to a theoretical strain of +/- 370 µε.
Table 4.6.2 – Summary of finite element modeling and constant-moment best test results.
162
It should be noted that the modeling conducted in this section attempts to simulate
an incredibly complex interaction of multiple events in a very simple manner. From
Figure 4.6.X it can be seen that significant bending occurs in the strain sensor when
under load. Shear lag stemming from the notably larger sides of the sensor relative to the
bottom “tub” of the sensor that houses the strain gage may cause differences in strain
response under tension and compression. Additionally, the notch created for strain relief
in the sensor causes changes in the strain field that may affect the sensors performance
when loaded. Furthermore, the anchorage system used may have differing effects when
subjected to tension or compression. Complexity arises from these issues and may be
superimposed when the instrument is loaded, causing uncertainty in the behavior of the
sensor.
However, these results are deemed appropriate as neither the bare gage values,
nor the strains recorded indicated a true compression to tension ratio of 1.00. Both values
were reasonable close to the desired C/T ratio, however. While it was expected that the
FE sensor model would be capable of attaining this ratio, it is also acknowledged that the
model operates under theoretically ideal conditions and the complexities described
previously lend variance to laboratory results.
As the finite element model of the strain sensor produced consistent results it is
felt that the constant-moment beam test would be an appropriate method to document the
individual behavior of the strain sensors. This documentation is required as they are
intended to record precise measurements of the De Neveu Creek Bridge. Additionally,
163
while it is expected that all the sensors behave in a similar manner, it is acknowledged
that not every mass-produced sensor is truly identical. Given the small magnitude of
measurements to be conducted with these sensors, minute differences may have
appreciable affects on individual sensor performance.
4.7 – Calibration of Individual Strain Sensors for Field Implementation
To ensure accurate performance of the strain sensors in the field, a calibration
procedure was performed documenting the unique response of each individual sensor
manufactured under tensile and compressive loads. Described within this section is
documentation of the test procedure and methods used, the data recorded from testing,
and analysis undertaken to produce an adjustment factor for individual sensor readings in
the data acquisition system. Individual calibration is required for all of the strain sensors
as irregularities in manufacturing produce behavior distinctive to each specific
instrument.
4.7.1 - Calibration Method and Equipment Used
Given the success observed with the test frame detailed in section 4.5 it was
decided that few modifications were required to utilize the frame for calibration. Other
possible methods of calibration were considered to document the response of the strain
sensors, however, all either proved to lack precision or were too costly. For example,
procedures involving a cantilever bending apparatus do not produce pure axial strains in
the sensors. Also, methods utilizing displacement monitoring, such as optical sensors,
were not available in the laboratory.
164
To ensure similar performance of the test frame and beams during the many load
tests, each roller support was welded to a primary member. Each roller received two tack
welds per side of the beams using a small wire welder. Welding the roller supports to
beams eliminated the possibility for independent movement but did not provide any
rotational restraint to the system. Figure 4.7.1 illustrates locations of welds.
Additionally, locations of members in the test frame were continuously monitored,
limiting the possibility of any relative movement that could introduce error into the
recorded data.
8’- 0”
3’- 0”2’- 6”
Load
W8x31 W6x20
1’- 6”
Welded roller
supports
Rigid beam
support
Figure 4.7.1 – Weld locations on beam members for the constant-moment load test.
All of the load tests were conducted in the following manner. Two sensors per
test were mounted to the W6x20 test beam, with one in compression and the other tension
as shown in Figure 4.5.3. Each individual nylon strain sensor was installed on the flange
with two Grade 8 5/16” diameter bolts. Washers were placed on the inner and outer
surface of the nylon so that neither the beam nor the fastening nut contacted the sensor
(recall the double washer recommendation of section 4.5.2). Each nut was then tightened
165
to a torque of 120 lb-in in alternating fashion. The lead wires of each sensor were then
connected to an additional length of wire, which was connected to the data acquisition
module. The other strain sensor was then installed in a similar manner. As was done
with the load tests conducted during development and experimentation of the nylon strain
sensor, complementary strain gages were bonded directly to the opposite flange of the
main test beam. The centerline of these gages were located at the same elevation, which,
in theory, should produce similar magnitudes of strain (Figures 4.5.3, 4.5.5). Also similar
to previous load tests, load and displacement were continuously monitored during testing
by a calibrated load cell, linear position sensor (LPS), and dial gage. The load cell was
located directly under the loading ram on the W8x31 spreader beam while the LPS and
dial gage were located at mid-span of the main test beam.
Prior to load tests, calculated values for shunt calibration of the strain gages and
sensors were produced. Individual resistances of the four strain channels (two 120-ohm
bonded gages, two 350-ohm strain sensors) were read with a multimeter and recorded in
a spreadsheet. The simulated tensile strain was then calculated using the measured
resistance of each shunt resistor and the manufacturer’s gage factor. Simulated tensile
strain magnitudes and resistance for each strain sensor may be found in Appendix D.
Once ready, the data acquisition system was initiated, the sensors and bonded gages shunt
calibrated, and load slowly applied. The hydraulic ram was hand operated, increasing the
load level as uniformly as possible until a maximum load of approximately 3-kips was
reached. Data acquisition was then suspended and the beam slowly unloaded. Strain
sensors were then removed and reinstalled in reverse locations to record their opposite
166
stain response, or removed entirely for two new sensors to be tested. A total of 35
sensors were tested in both compression and tension.
4.7.2 - Data Recorded during Load Tests
To develop calibration factors for implementation of the strain sensors in the
field, significant post-processing of the data occurred. As noted, each individual
calibration test recorded strain, load and deflection data documenting the response of two
independent strain sensors in tension and compression. Additionally, complementary
bonded gages noted in Figure 4.5.5 were also monitored to provide a baseline value for
comparison. The strain gages bonded directly to the beam are considered to be the actual
value of strain imposed on the W6 test beam and, thus, all calibration was subject to the
accuracy of these gages. Prior laboratory experiments and testing combined with in-situ
and other field installations of similar electrically resistive bonded strain gages have been
very successful and are considered acceptable. Furthermore, the analytical study
conducted previously supports the accuracy of the bonded strain gages (section 4.6.1).
In order to quantify individual strain sensor response relative to the bonded strain
gages, a calibration factor was developed. Given the predominantly linear response of
the strain sensors, it was decided that a simple coefficient multiplier would be
satisfactory. The following expression illustrates the calibration factor used,
( )SENSOR i
i
Gage
CFε
ε= (4.7.1)
167
where ( )SENSOR iε is the strain recorded in Nylon sensor “i”, and Gageε is the strain
recorded in the corresponding bonded strain gage. The typical measured strain response
of both the bonded strain gages and the portable sensor is shown in Figure 4.7.2.
Figure 4.7.2 – Typical response of strain gages and sensors under applied loading. The load
indicated refers to that applied by the hydraulic ram to the test frame.
It can be seen from this figure that the strain sensors and gages (solid lines) very
nearly match their linear trend lines (dotted), which pass through the origin. Further, the
R-squared values for a linear fit of the measured data are noted, indicating that the trend
lines are very nearly equal. On the other hand, discrepancies exist. These differences
may be attributed to a delay in the strain response of the gages and sensors when loading
is applied rapidly. Note the slightly curved response of the data lines in Figure 4.7.2, and
the pronounced differences in Figure 4.7.3.
168
A hand-actuated hydraulic pump was utilized for loading and true monotonic
loading increase was not possible. Figure 4.7.3 illustrates this delay in response. It is
important to note that the same sensors and configuration as from Figure 4.7.2 were used,
however, the data depicted in Figure 4.7.3 was disregarded as erroneous due to the rapid
loading.
Figure 4.7.3 – Erroneous response of strain gages and sensors under rapid, non-monotonically
increasing loading.
To produce the calibration factors for each gage, a load level of 2500 lbf was
arbitrarily selected at which strain readings would be analyzed. From figure 4.7.2 it can
be seen that when loaded at an appropriate rate the data forms a nearly linear line (R2 =
0.99), thus any load level would be appropriate to select data from. At this load, three
strain values were sampled from the data, containing values corresponding to both
169
sensors mounted to the beam and both bonded strain gages, and averaged. The ratios for
compression and tensile response of the strain sensor under loading were computed.
Table 4.7.1 illustrates typical calculations performed for each load test, producing
calibration factors for two gages simultaneously.
Top Nylon [uStrain] Top gage [uStrain] Bot. Nylon [uStrain] Bot. gage [uStrain]
-172.4567 -174.029 183.514 180.1114
-172.4568 -174.0334 183.5069 180.1181
-172.4558 -174.0382 183.4995 180.125
Average = -172.46 -174.03 183.51 180.12
St Dev = 0.00 0.00 0.01 0.01
Calibration
Factor =0.991 1.019
Sensor #005 Sensor #006
Table 4.7.1 – Calculation of calibration factors.
4.7.3 - Individual Calibration Factors
Calibration factors developed for use with field-acquired data are listed in table
4.7.2. If a reading is indicated compressive, multiplication of the recorded strain reading
by the compressive calibration factor unique to that gage will produce the corrected strain
reading. Likewise, the opposite is true for tensile readings. It can be seen that for a
majority of the strain sensors, tensile and compressive response is similar. From the
results of the FE sensor model, calibration factors should theoretically be identical
between tension and compression. However, the anchorage behaves differently in
compression relative to tension, varying the response of the strain sensors. Overall, the
calibration factors for most sensors are relatively similar. It can be seen that in all but
three sensors below, the compression calibration factor was larger than the tensile factor,
indicating a consistently different response.
170
Sensor Compression Tension
001 1.064 0.964
002 1.093 0.965
003 1.093 1.159
004 1.145 1.045
005 0.991 0.925
006 1.026 1.019
007 1.006 0.975
008 0.877 0.786
009 1.053 1.070
010 1.123 1.091
011 1.080 1.043
012 1.020 0.999
013 1.139 1.028
014 1.151 1.073
015 1.069 1.013
016 1.036 0.999
017 1.069 0.967
018 0.983 0.935
019 1.064 0.972
020 1.129 1.044
021 0.978 0.934
022 0.911 0.851
023 1.079 1.044
024 0.999 0.945
025 1.073 1.026
026 1.103 1.026
027 1.020 0.959
028 1.131 1.033
029 1.049 0.985
030 0.952 0.922
031 0.957 0.940
032 0.979 0.923
033 0.962 0.910
034 1.111 1.026
035 0.989 0.997
Average 1.043 0.988
Table 4.7.2 – Calibration factors developed for correction of laboratory acquired readings.
171
Chapter 5 – Proposed Load Test
5.0 – Introduction
By conducting a load test of the De Neveu Creek IBRC Bridge, physical data is
produced aiding in the long-term monitoring of the structure. Also, valuable information
pertaining to the physical behavior of the bridge may be produced, allowing for analysis
of its structural performance and also the design methods used. In order to carry out the
load test for the IBRC project, the structure will be instrumented with strain sensors
detailed in previous sections and load tested. The arrangement of sensors and reasoning
for their placement is outlined below. Required equipment is also outlined in this section.
Finally, the load test procedures, vehicles, and expected results are contained herein. The
anticipated time of load test is the spring of 2006.
5.1 – Load Test Objectives and Instruments
The strain sensors outlined previously in section 4 will be used to obtain strain data
during testing and data acquisition focuses on the following objectives:
1. Strain profile of girders and deck (validate composite behavior)
2. Transverse distribution of wheel loads in bridge deck
3. Longitudinal distribution of load between girders
These objectives intend to complement the deflection data recorded during the previous
benchmark load test conducted by the University of Missouri – Rolla. Acquisition of
data periodically over the monitoring period will track degradation of the deck. Figure
5.1.1 illustrates the location of instruments to be used in executing these objectives.
172
Mid-span
N
Enclosure Box
1
2
3
4
5
6
7
Third-point
of span Longitudinal strain sensor mounted to bottom of girder
Array of (5) strain sensors and string potentiometer for
transverse wheel load distribution
Array of (4) strain sensors for strain profile of girder and
FRP-reinforced deck
Figure 5.1.1 – East half of the De Neveu Creek IBRC Bridge indicating instrument locations. 32 total
strain sensors, two string potentiometers.
Longitudinal distribution of load between the girders will be conducted by
attaching individual strain sensors to the underside of bridge girders at mid-span and a
third-point of the span. As there are seven girders, fourteen individual sensors will be
installed with each sensor being centered transversely on the girder. Data collected
should then be analyzed using a procedure similar to that noted by Turner (2003).
Individual strain values measured in a girder will be divided by the total strain of all
seven girders recorded at similar locations, producing a fraction of total strain
experienced by that individual girder. This allows girder distribution factors to be
generated using the experimental data collected.
173
Additionally, the global displacement of each girder should be monitored with a
surveying total station. Prisms should be magnetically mounted to the existing steel
plates located on the bottom of each girder from the previous load tests. Observation of
girder deflections during load testing will provide data allowing the results of the
previous load tests to be more directly correlated.
The strain profile of the bridge deck and girders is important to verify that
composite action of exists between the deck and girders. The structure was designed
assuming composite action and verification of such behavior is required. Additionally,
degradation of this composite behavior over time will be evaluated over the monitoring
period of this project. By locating strain sensors at the girder bottom, girder mid-height,
girder top flange, and on the FRP-reinforced deck as indicated in Figure 5.1.2, the strain
variation over the height can be recorded. Two instances of this array will be installed at
third-point of the span, totaling eight strain sensors (Figure 5.1.1). If the loads used in
testing invoke elastic response of the structure, the strain profile for the girder-deck
system will be linear as indicated in Figure 5.1.2, allowing for a rapid and simple
determination of the degree of their composite behavior through locating the neutral axis.
Figure 5.1.3 provides an illustration of differing levels of composite behavior, ranging
from full interaction between the deck and girder (diagram c) to no interaction between
the components (diagram a).
174
4”
54”
37”
51”
n.a.
8”
25”
Figure 5.1.2 – Section of girder and deck for locating strain sensors. The strain profile on the right in
indicative of a fully composite cross section based on four sensor readings.
Figure 5.1.3 - Composite behavior stress profiles through a typical deck section (Lenett et al. 2001)
The transverse distribution of wheel loads throughout the FRP-reinforced deck is
the final objective of the load test. The FRP-grillage used for primary reinforcement of
the concrete bridge deck is a new material and structural system. Significant laboratory
testing has been conducted to date (Bank et al. 1992a; Bank et al. 1992b; Jacobson 2004),
but in-situ validation is lacking. Work by Conachen (2005) attempted to address the
issue, but due to the failure of instruments, little insight into the transverse behavior of
the bridge’s deck resulted. Thus, two arrays of strain sensors will be installed on the
underside of the bridge deck to evaluate wheel load distribution in the deck. Further,
evaluation of the AASHTO (1998) recommendations can be made.
175
The upper surface of the bridge deck currently receives traffic, prohibiting the
installation of sensors at the roadway surface. Each array will contain five sensors,
located near the mid-span of the bridge deck (centered between the girders). Sensors will
be spaced at intervals of 18” with the middle sensor located at the target wheel position.
Furthermore, the sensors should be arranged in the staggered manner depicted in Figure
5.1.4.
2
1
5 spaces @ 18” o.c.
Strain sensors
oriented in
transverse direction
String potentiometer
centered between
sensors
3
Centerline of target
wheel load
Figure 5.1.4 – Plan view of strain sensors to monitor transverse wheel load distribution. Sensors are
located approximately at mid-span of bridge.
This staggering of sensors allows for observation of a larger region of deck while
minimizing the number of sensors required. Since the sensor arrays are to be located
significantly far from the abutments, the bridge’s skew is not expected to have any affect
on the behavior of the deck. The longitudinal spacing of the sensors is based in part by
research conducted at the University of Wisconsin-Madison (Dieter 2002) which focused
load tests of FRP-reinforced concrete slabs. Results produced during testing indicated
that the effective distribution region of a single HS-20 wheel load (approximately 20.8
176
kips) was no more than 36” in either direction from the contact area. Figure 5.1.5
illustrates the lateral location of transverse sensor arrays and the string potentiometer.
21
3’-2.5” 3’-2.5”
Transverse sensor
String potentiometer
mounted on steel tube
Figure 5.1.5 – Section view of strain sensors for transverse wheel load distribution.
In addition to the five strain sensors in each transverse sensor array, a string
potentiometer will be installed to measure relative displacement at mid-span between the
girders and the deck. Each potentiometer unit should be attached to a rigid support,
preferably a steel tube, and secured adequately as shown in Figure 5.1.5. The moveable
end of the potentiometer should be withdrawn from the base unit and attached to the
substrate to be monitored by a hook or other mechanism in-line with the string. String
potentiometer model number PA-30 manufactured by UniMeasure, Inc is recommended
for use. These devices have a measuring string 30” long, which gives flexibility in
attaching the potentiometers. Figure 5.1.6 provides photographs of a string potentiometer.
Displacement data is intended to provide insight into the flexural response of the deck
under load in-situ deflection response.
177
Moveable end in-line
and free to rotate
Measuring string
Figure 5.1.6 – String potentiometer manufactured by UniMeasure. The right photograph illustrates
a proper connection for measurements.
5.2 - Permanently Installed Equipment
As this study is aimed at evaluating the long-term behavior of the De Neveu
Creek IBRC Bridge, some permanently equipment is required to be installed reducing
effort for future tests and also to provide a greater degree of coherence between data
collected. Currently, protective PVC piping and lead wires for the instruments have been
installed, as well as an electrical enclosure box. The individual sensors have not been
installed on the bridge, nor have their embedded mounting bolts and require installation
anticipated for the spring of 2006.
5.2.1 - Lead Wiring for Instruments
The sensor arrays described above entail a total of 32 strain sensors and two string
potentiometers. Each strain sensor will operate with a three-wire quarter bridge circuit
(section 3.3), while the string potentiometers require three wires also. To provide these
178
wires for each sensor, an appropriate length of NEMA Category 5e (Cat-5) wire was run
from the sensor location to a weather-proof, non-metallic enclosure box, which is
discussed later. Cat-5 wire is composed of eight individual copper wires, twisted in pairs,
and enclosed with vinyl sheathing. Three wires will be used for the strain sensors,
providing five extra wires in the event of damage or breakage. To protect the wires, they
were fed through conventional 1” PVC pipe, which was then sealed at all joints using a
PVC primer and adhesive. The PVC was rigidly affixed to the bridge girders and deck
using plastic conduit hangers and concrete screws. Figure 5.2.1 illustrates the PVC plan
layout installed on the De Neveu Creek Bridge for this project. Figures 5.2.2 and 5.2.3
provide photographs of the conduit installation. It is of note that all wires were run the
minimum length possible and terminated at close to the sensor location as possible with
appropriate lengths of wire for attachment.
Mid-span
N
Enclosure Box
1
2
3
4
5
6
7
Mid-span longitudinal sensors (7 wires)
Third-point of
span
Third-span longitudinal sensors (7 wires)
Transverse wheel load distribution instruments (10 sensor wires, 2
string potentiometer wires)
Girder and deck strain profile sensors (8 wires)
Figure 5.2.1 – Plan of sealed PVC pipes containing lead wire runs for individual instruments.
179
Figure 5.2.2 – PVC piping terminating at the enclosure box. Dark regions along pipes are excess
primer used during sealing.
Figure 5.2.3 – Installation of the PVC piping housing instrument lead wires along girder #1. Note
the pipes running laterally from the four main pipes carrying wires to interior girders.
180
5.2.2 - Enclosure Box and Screw Terminals
The enclosure box was mounted on the north end of the east abutment below the
bridge deck and adjacent to girder number 1. The box is constructed of painted fiberglass
and contains a weather-proof lid that can be locked to prevent unauthorized access.
Additionally, electrical screw terminals were provided inside the enclosure to allow for
termination of the lead wires at the abutment. These terminals are isolated conductors
that retain the lead wires from instruments on the bridge and carry the signal to
connecting wires leading to the data acquisition system. It is intended that the six pin
Mini-DIN connecting wires required by the DBK43A and DBK65 modules of the data
acquisition system will be installed and connected to these terminals prior the load test.
Figure 5.2.4 illustrates a typical screw terminal connection while Figure 5.2.5 illustrates
the connection diagram in the enclosure box for the lead wires as installed in the field.
As an additional note, installation of the screw terminals required penetration of the
enclosure’s fiberglass shell but was thoroughly sealed with a silicon caulk, maintaining
the weather-tight integrity of the enclosure. The enclosure can be seen in Figure 5.2.6
with the screw terminals installed and prior to lead wire connection.
Individual Screw
Terminal
Lead Wire from
Sensor on Bridge
Connecting Wire to Data
Acquisition System
Rear Wall of Enclosure Box
Figure 5.2.4 – Detail of a typical screw terminal connection.
181
(21) Terminals for mid-span longitudinal strain sensors
Girder
Sensor 1
Girder
Sensor 7
Girder
Sensor 1
Girder
Sensor 7
(21) Terminals for third-span longitudinal strain sensors(12) Terminals for
Girder #2 strain
profile sensors
(12) Terminals for
Girder #1 strain
profile sensors
(15) Terminals for transverse wheel load sensors
and string pot between Girders #2 and #3
LM-1 LM-3LM-2 LM-5LM-4 LM-7LM-6P1-B P1-M P1-T P1-D
LT-1 LT-3LT-2 LT-5LT-4 LT-7LT-6P2-B P2-M P2-T P2-D
(15) Terminals for transverse wheel load sensors
and string pot between Girders #1 and #2
T1-W2 T1-MT1-W1 T1-E2T1-E1 T1-DT2-W2 T2-MT2-W1 T2-E2T2-E1 T2-D
Sensor Farthest
WestSensor Farthest
East
Sensor Farthest
WestSensor Farthest
East
Girder
Bottom
Bottom
of Deck
Girder
Bottom
Bottom
of Deck
Figure 5.2.5 – Diagram of lead wires terminated in the screw terminals in the enclosure box.
Figure 5.2.6 – Enclosure box housing lead wire connections.
182
Nomenclature used in the enclosure box diagram is as follows:
Transverse Wheel Load Distribution Sensors:
T1-XX indicates the deck span between girders #1 and #2 while T2-XX refers to
the deck span between girders #2 and #3. Figure 5.2.7 illustrates the labels.
• T1-W2 – Transverse strain sensor west most from the middle of span.
• T1-W1 – Transverse strain sensor west most from the middle of span.
• T1-M – Transverse strain sensor located at mid-span.
• T1-E1 – Transverse strain sensor east most from the middle of span.
• T1-E2 – Transverse strain sensor east most from the middle of span.
• T1-D – String Potentiometer displacement transducer located slightly east of mid-
span.
2
1
3
T1-W
1
N
T1-W
2
T1-M
T1-E1T1-E2
T1-D
T2-W
1
T2-W
2
T2-M
T2-E2
T2-E1T2-D
.
Centerline of target
wheel load
Figure 5.2.7 – Labels for transverse strain sensors at mid-span of the bridge.
Girder Strain Profile Sensors:
P1-X indicates sensors installed at third-span of girder #1 while P2-X refers to
sensors installed at third-span of girder #2. Figure 5.2.8 illustrates the labels.
• P1-B – Sensor located on bottom flange of girder, approximately 4” from bottom.
183
• P1-M – Sensor located near the mid-depth of girder, approximately 37” from
bottom of girder.
• P1-T – Sensor located on the underside top flange of girder, approximately 3”
from top of girder (51” from bottom)
• P1-D – Sensor located on the FRP-reinforced concrete deck atop the girder,
adjacent to the top flange of girder.
P1-D
P1-T
P1-M
P1-B
1
P2-D
P2-T
P2-M
P2-B
2
Figure 5.2.8 – Labels for girder strain profile sensors at third-span.
Longitudinal Sensors
LM –X indicates a strain sensor located at mid-span of the structure while LT-X
refers to strain sensors located at third-span of the bridge. “X” indicates the girder
number the sensor is located on. Figure 5.2.9 illustrates the labels.
184
Mid-span
N
1
2
3
4
5
6
7
Third-point
of span
LM-1
LM-2
LM-3
LM-4
LM-5
LM-6
LM-7
LT-1
LT-2
LT-3
LT-4
LT-5
LT-6
LT-7
Figure 5.2.9 – Labels for longitudinal strain sensors.
5.2.3 - Installation of Strain Sensors
As noted elsewhere in this document, the strain sensors developed for this project
are to be mounted to the De Neveu Creek Bridge using an anchorage system consisting of
¼” diameter steel bolts embedded in the concrete girders and deck. Two anchor bolts are
required for each sensor and require washers on all exposed nylon surfaces. A diagram
of the anchorage system is provided in Figure 5.2.10.
Strain SensorBolt
w/nut
Standard Washers
Drilled hole w/Bolt
set in adhesive
1”
Figure 5.2.10 – Illustration of the anchorage system for strain sensors.
185
Each 3” long by ¼” diameter bolt will be set in a 5/16” diameter holes drilled into
the concrete. Embedment should be approximately 1 inch (Powers 2005). After drilling
holes, they should be blown clean and any debris moved prior to injecting the adhesive.
Once the adhesive has been injected to the hole, the anchor rod should be inserted,
twisting the rod as it is embedded. The gel time of adhesive is 15 minutes, requiring that
the anchor rod be temporarily restrained by duct tape or other means while the adhesive
cures. Full cure time for the recommended adhesive is 24 hours (Powers 2005).
However, concern is warranted when drilling into the prestressed concrete girders. The
construction plans for the De Neveu Creek Bridge indicate that a minimum of 1” cover is
provided for all steel reinforcing in the bottom of girders(WiDOT 2003). Penetration of
stressed steel tendons contained in the girders can be extremely dangerous and, thus,
maximum embedment of the anchor bolts will be 1 inch for safety. When the anchor bolt
are set and cured, each sensor should be “sandwiched” with standard washers. The
retaining nut should be tightened to 120 lb-in.
The anchorage system to be used recommended for this project is as follows:
• Anchor Bolts – Powers Fasteners straight anchor rods, ¼” dia. x 3” long of
ASTM A307 steel, product number #07980.
• Washers and Nuts – ½” o.d. x ¼” i.d. plain steel washers and standard ¼”
diameter nuts. Both are included by Powers Fasteners with purchase of anchor
rods.
186
• Adhesive – Powers Fasteners PowerFast+ adhesive system, Fast Set formula. The
It is of note that at 75 o
F, only 15 minutes of dispensing time is provided by the
epoxy (Powers 2005).
• Drill Bit – 5/16” diameter carbide masonry bit, driven by electrical hammer drill.
It should be noted that when subjected to strain levels anticipated during this load test
(less than 200 µ) the total force required to be sustained by the anchor rods embedded in
the concrete is approximately 12 lbf (Figure 5.2.11).
Strain Sensor
F
( ) ( )20.15 200 400,000 12SensorA E in psi lbfε µε= = =i iF
Anchor Rod
Estimated force in strain sensor:
FF/2
F/2
Friction Force
of Washers
Figure 5.2.11 – Approximation of the force acting on the anchor rod.
Assuming that the anchor rod is rigid, this force is opposed in compression and tension
by the adhesive bonded to the anchor rod present in the hole drilled into the concrete.
From this, a small distribution of stress (both tensile and compressive) is produced in the
epoxy, which has compressive and tensile strengths of 11,125 psi and 7,250 psi,
respectively (Powers 2005). It is felt that these stress levels are not appreciable enough to
187
warrant further concern and it is anticipated that even at large strain levels, the anchor
bolts and epoxy will be sufficient.
5.3 – Load Test Vehicles and Test Configuration
In order to maintain continuity with the data collected during load testing in
September 2004 by the University of Missouri – Rolla and the University of Wisconsin –
Madison, use of similar test vehicles is recommended. As documented by Conachen
(2005), three-axle dump trucks loaded with loose gravel were used for the load tests and
referred to as a “H-20 Dump Truck.” Figure 5.3.1 shows the approximate dimensions of
the test vehicle.
14’-0”
4’-6”
6’-0”
14’-0”
4’-6”
23’-8”
6’-0” 7’-0”
Figure 5.3.1 – Test vehicle dimensions for UM-R/UW-M load test. Adapted from Conachen (2005).
The H-20 Dump Trucks used in testing of the De Neveu Creek Bridge had an
average front axle weight of 26,013 lbs., an average rear tandem (both rear axles) weight
of 49,913 lbs., and a average total weight of 74,946 lbs. (Conachen 2005). As noted
prior, the use of similar test trucks is recommended for all future testing.
188
5.3.1 - Load Test Objectives
The objective for each load test is described below.
Load Test Objective Addressed
1. Longitudinal distribution of load between girders and overall
girder deflections.
2. Strain profile of girders and deck.
3. Transverse distribution of wheel loads in bridge deck.
During the previous testing, four load tests were conducted on the De Neveu Creek
Bridge (structure B-20-148) to monitor load distribution between girders. As the bridge
is currently under traffic, load tests similar to those conducted by the University of
Missouri - Rolla are not possible. Rather, it is anticipated that only a single traffic lane of
the bridge be closed to traffic during testing, while the other lane will require temporary
traffic stoppages to conduct each load test.
Continuous data acquisition of each load test should be performed from start to
finish of all tests. To perform each load test, readings of appropriate sensors should be
made before the test vehicles are placed on the structure, providing a baseline for each
individual test. Readings taken from all sensors before the test vehicles are located on the
structure should then be tarred, or “zeroed.” All the test vehicles should then be driven
onto the structure and located in their intended positions. When all vehicles are in their
correct position they should remain idle for five minutes and then driven off the structure.
Once the test vehicles are absent from the bridge, another settling period of five minutes
should be conducted before the data acquisition is stopped. Finally, resting periods
189
during data acquisition allow for any dynamic effects induced by movement of the test
vehicles to dissipate, providing static data for analysis. However, in the event that any
additional vehicles cross the structure during data acquisition, documentation should take
place to clarify the data when analyzed later.
The protocol for deflection measurements made with surveying equipment is
similar to the data acquisition system. Readings of girder deflection should be made
prior to locating the test vehicles on the bridge, after the vehicles have been located on
the structure and the settling period finished, and finally after the vehicles are removed
from the bridge and another settling period complete.
5.3.2 - Load Test Configurations
Load Test #1 will be conducted similar to the fourth load test conducted by the
University of Missouri-Rolla (Bank 2005). However, as coordinating separate test
vehicles on the structure in a rapid manner may prove difficult, only three test vehicles
are recommended. It is anticipated that use of three test vehicles will produce moments
in the bridge girders large enough to produce significant strain levels. Usage of fewer
vehicles may cause strains in the girders smaller than 30 µε; larger strain levels tend to be
more reliable. The train of test vehicles are be positioned centrally above girder 2, as
indicated in Figure 5.3.2.
During this test the 14 longitudinal strain sensors should be activated to observe
the distribution of load among girders. Based upon an estimated axle load (AASHTO
lane load) of 25-kips, the projected strains to be observed in the sensors are presented in
190
Table 5.3.1. Additionally, observation of the overall girder deflections should be
recorded during this test.
DWT Device
Strain Gauges
“Rigid” Strut
17.5’
42’
66.5’
130’
(3) Test Vehicles
21 3 4 5 6 7
Figure 5.3.2 – Load Test 1 test vehicle locations.
Sensor Strain (µεµεµεµε)LM-1 145
LM-2 145
LM-3 132
LM-4 105
LM-5 66
LM-6 46
LM-7 20
LT-1 107
LT-2 107
LT-3 97
LT-4 78
LT-5 48
LT-6 34
LT-7 15
Mmid-span = 58800 k-in
M3rd point = 43320 k-in
0.22
0.22
Load Test 1
Distribution Factor
0.20
0.16
0.10
0.07
0.03
0.22
0.22
0.20
0.16
0.10
0.07
0.03
Table 5.3.1 – Load Test 1 estimated strain magnitudes. Distribution numbers are based on a single
lane loading and corresponding load test by UM-R (Bank 2005).
191
Strains produced in Table 5.3.1 were computed using the following expression,
( ) i bottomi
Composite
M yGDF
E Iε
×=
× (5.3.1)
where IComposite = 589,843 in4, E = 5,583 ksi, ybottom = 36.84” and Mi refers to the
moments at mid-span (65’) and third-point (88’ from left) produced from the loading
illustrated in Figure 5.3.2. Moments were calculated using a 2-dimensional linear-elastic
model in MASTAN2 containing the section and material properties listed previously
(Ziemian and McGuire 2002). GDF in the above expression refers to the distribution
factors of the spring 2004 load test conducted by the University of Missouri – Rolla
(Bank 2005). All properties are that of a fully composite section and compare well with
the properties outlined in Conachen (2005).
17.5’
22’
36’
42’
46.5’
60.5’
66.5’
71’
85’
130’
P ˜ 25 kips, each axle load
Figure 5.3.3 – Axle positions of a single girder during Load Tests 1 and 2. Drawing not to scale.
Load Test 2 uses the same three-truck trains as the previous load test. However,
instead of placing a line of wheel loads directly over a girder, a truck train will be
centered above girders 1 and 2. Figure 5.3.3 provides locations of the test vehicles.
192
DWT Device
Strain Gauges
“Rigid” Strut
17.5’
42’
66.5’
130’
(3) Test Vehicles
21 3 4 5 6 7
Figure 5.3.4 – Load Test 2 test vehicle locations.
During this test the two arrays of strain profile sensors (Figures 5.1.2 and 5.2.8)
should be active for data acquisition. Results obtained during this test will provide
insight into the composite behavior of the girder and concrete deck. Estimated strain
values using the girder distribution factors reported in Table 5.3.1 for the strain profile
sensors are found in Table 5.3.2 below.
Sensor yi Strain (µεµεµεµε)
P1-B 32.84 95
P1-M 0 0
P1-T -17.16 -50
P1-D -25.16 -73
P2-B 32.84 95
P2-M 0 0
P2-T -17.16 -50
P2-D -25.16 -73
Load Test 2
Table 5.3.2 – Estimated strains for girder profile sensors installed at third-span of girders 1 and 2.
Negative values indicate compression while positive values refer to tension.
193
Load Test 3 will be conducted to observe the region in which load is distributed in
the FRP-reinforced deck under a single axle load. The front wheels of a test vehicle truck
will be located directly over the sensor arrays installed on the underside of the deck. It is
assumed that the rear tandem axle is of the test vehicle is far enough from the front axle
as to not affect performance of the sensors. A wheel will be positioned directly over the
array between girders 1 and 2, which is centered on the deck span. Figure 5.3.4
illustrates the location of test vehicle wheels at mid-span of the bridge. The lateral
positioning of the test vehicle will be such that both sensor arrays may be activated and
observed simultaneously.
21
EQ.
3
EQ.
Figure 5.3.5 – Load Test 3 test vehicle wheel locations at mid-span of the bridge. Only front wheels
of the test vehicle should be located at mid-span.
5.4 – Data Acquisition System
The data acquisition system to be used for testing consists of an IOTech DaqBook
2001 module, three IOTech DBK43A strain gage modules and an IOTech DBK65
transducer module. The DaqBook acts as an analog-to-digital converter for the system
while and the DBK modules perform signal condition of the strain sensor and transducer
194
signals. An overview of data acquisition operation is presented in section 3.1.
Photographs of the modules are found in Figure 5.4.1 through 5.4.4.
Figure 5.4.1 – Photograph of the data acquisition system used for load testing. Pictured from top to
bottom are three DBK43A modules, the DBK65 module and the DaqBook 2001 module. Front panel
(left) and rear panel (right).
Figure 5.4.2 – Photograph of the DaqBook 2001. Front panel (left) and rear panel (right).
195
Figure 5.4.3 – Photograph of the DBK43A strain gage module with cover panel removed. Front
panel (left) and rear panel (right).
Figure 5.4.4 – Photograph of the DBK65 transducer module with cover panel removed. Front panel
(left) and rear panel (right).
Recording of data during the five load test configurations should be conducted in
a continuous manner. As noted previously, the strain readings should be tarred to provide
a starting value of the sensors, test vehicles located on the bridge and allowed to rest, then
driven off the structure and followed by a settling period. The data acquisition system
should be active and recording for this entire process. A sampling rate of 25 Hz is
recommended for acquisition to better document any rapid response of the bridge to the
loads. Previous efforts in bridge monitoring have utilized sampling rates between 25 Hz
and 40 Hz successfully (Bridge Diagnostics Inc. 2002; Lenett et al. 2001). Additionally,
196
the fact that continuous acquisition of data consumes a large amount of computer storage
space must be addressed. Use of very rapid sampling rates will produce unnecessary
amounts of data and occupy an inordinate amount of hard drive space of which a majority
of such is unnecessary. For these reasons an effort should be made to position vehicles
on the bridge as quickly as possible, limiting the amount of data collected with the
recommended 25 Hz sampling rate.
5.4.1 - Signal Conditioning Modules
The signal conditioning modules used for this load test will be the DBK43A strain
gage module and the DBK65 transducer module. Configuration of each is provided
below.
The DBK43A strain gage module requires few modifications to prepare it for use.
Analog filtering in all strain gage channels will be utilized given significant possibility of
environmental interference produced in the lead wires. The DBK43A modules are
supplied with a 3.7Hz Butterworth filter (section 3.1) and are enabled by changing the
electrical jumpers on the circuit board. The proper orientation of jumpers is given on the
circuit board. Figure 5.4.5 illustrates the location of the filters on the circuit board and
their enabling jumpers.
197
Front Panel
Rear Panel
Analog
filters and
jumpers
Figure 5.4.5 – Analog filter locations on the DBK43A module.
As a quarter-bridge circuit will be used for all strain sensors, three bridge
completion resistors are required to construct the Wheatstone bridge circuit. An
introduction to Wheatstone bridge measurements is provided in section 3.2. The
DBK43A uses removable “headers” that can be configured for full, half or quarter bridge
circuits. Each sensor channel requires an individual header, which is illustrated in Figure
5.4.6 below.
“A”“B”
“E”Strain
Gage
Completion Resistor
“Header”
Jumper
configuration
Completion
resistors
Figure 5.4.6 – Quarter Bridge circuit and completion resistor configuration for use with the strain
sensors. Adapted from (IOTech 2005).
198
Note that both completion resistors and jumper settings must be modified as
shown in Figure 5.4.6 to properly configure the quarter bridge strain gage circuit. As
resistance of each strain sensor is 350-ohms (±0.3%), the use of high-precision
completion resistors is required. Thus, 350-ohm (±0.1%) completion resistors were used
to build each resistor plug, completing a nearly balanced Wheatstone bridge circuit.
Location “H” illustrated on the completion header in Figure 5.4.6 is reserved for a shunt
calibration resistor. The shunt calibration resistors recommended for use in all strain
gage channels are 165-kOhm. When used with the strain sensors (Gage Factor = 2.105,
350-ohm), this shunt resistor produces approximately 1000 µ in tension, which is
greater than the expected strain response during the field test. Each shunt resistor should
be measured with a multimeter or other precision instrument so that the simulated strain
may be calculated. Refer to section 3.2 for further discussion on shunt calibration.
5.4.2 – Connection to Strain Gage Modules
The connection interface between the DBK43A module and each strain sensor
requires the use of a mini-DIN, 6-pin plug, similar to PS/2 plugs commonly used for
computer keyboards and mice. Figure 5.4.7 illustrates the pin numbering for
configuration of the mini-DIN plug.
199
Looking @
Module
Looking @
Plug
12
34
56
1 2
3 4
5 6
Figure 5.4.7 – Typical pin numbering of a mini-DIN plug.
The quarter bridge configuration used for this project requires that the following
pins be connected to the noted wires as follows:
• Pin 5 – positive voltage signals, green wire.
• Pin 4 – negative voltage signals, yellow wire.
• Pin 3 – signal sent to ADC for recording.
Figure 5.4.8 illustrates the connections used for this project.
5 (green) +Vexec
4 (yellow)
3 (orange)
-Vexec
To ADC
Pin Number Strain
Gage
Exterior Interior
Figure 5.4.8 – Pin numbering of mini-DIN plugs used for this project with typical color-coding.
200
Once the filters are enabled, completion headers configured properly, and plugs attached
to strain sensors, the DBK43A hardware is ready for strain gage measurement.
The DBK65 transducer module only requires specification of the excitation
voltage for each instrument attached to the individual channels. An excitation of 10 volts
is recommended for the UniMeasure string potentiometers used in this project. Selecting
the appropriate jumper setting on the circuit board of the DBK65 module sets the
excitation voltage. Figure 5.4.9 illustrates the location of excitation jumper settings.
Front Panel
Rear Panel
Excitation
voltage
jumpers
Figure 5.4.9 – Location of the excitation voltage jumpers on the DBK 65 circuit board.
5.4.3 - Acquisition Software
The software to be used in this project is DASYLab. Section 3.5 outlines a
general procedure for configuring four strain gage channels and two transducer channels
using the DBK43A and DBK65 signal conditioning modules. The worksheet required
201
for monitoring the individual strain sensors and string potentiometers is constructed in a
similar manner as described previously, adding the appropriate number of additional
channels for each individual load test. It is recommended that separate worksheets be
used for each individual load test to speed in-field acquisition and allow the user
opportunity to only use those channels necessary for acquisition during load tests.
5.4.4 - Error Correction in Readings
As noted in section 3.3, errors in strain readings can be produced by a number of
sources. However, a number of simple correction methods are available to increase the
accuracy of measurements. Directly pertinent to this project are error caused by lead
wire attenuation, thermal changes and Wheatstone bridge non-linearity.
Attenuation of signal caused by lead wire resistance dampens the electrical
change of a strained Wheatstone bridge circuit. Lead wires installed on the De Neveu
Creek Bridge have a wide array of lengths, with the maximum length of wire installed
being approximately 120.’ However, the wiring used is of relatively low resistance. For
example, a 30’ run of wire has approximately 1-ohm of resistance. If the resistance in
lead wires is assumed to vary linearly with length, the longest lead wires would then
posses approximately 4-ohms of additional resistance. Using the correction expression
noted in section 3.3, the following calculation provides an adjustment coefficient for
strain sensor readings.
( ) ( )350 4 1.01350
g Lactual read read read
g
R R
Rε ε ε ε
+ += = =
(5.4.1)
202
It can be seen that for the longest lead wire lengths used in this project, only a 1%
error is introduced in the readings. For this reason, lead wire attenuation may be omitted
from analysis.
Thermal changes of the structure, electrical wiring and strain gage itself may also
effect strain measurements. However, it is assumed that straining of the structure due to
thermal effects will not alter measurements taking during load testing as the recording
method is designed to be implemented during a short-term live loading only.
Additionally, care has been taken to avoid any heating of the lead wires during
acquisition. Finally, excitation voltage of the strain gages contained in the strain sensors
has been selected to eliminate any local heating of the sensor. Further detail is provided
in section 3.3.
Wheatstone bridge non-linearity can also effect strain measurements. However,
significantly large strain levels must be experienced for the non-linear nature of the
bridge to effect measurement. It is expected that during this testing, strains caused by the
test vehicles will not be large enough to warrant consideration.
203
Chapter 6 – Summary and Conclusions
6.0 – Summary
A great deal of information is presented within this document, covering a review
of prior monitoring efforts; data acquisition and strain measurement; the development
and validation of a portable strain sensor; and a proposed load test.
The review of literature presents an overview of recommended monitoring
guidelines, an introduction to the De Neveu Creek IBRC Bridge and results from an
initial live load test conducted in the spring of 2004. Four additional monitoring projects
were also presented, illustrating different methods used to monitor structural response to
live load, and also methods available to analyze data collected during testing. These
sources provide an excellent introduction to the monitoring of bridges for their behavior
under short-term live loading.
As data acquisition and strain measurement is complex, a brief introduction of
basic strain measurement was warranted. Rudimentary discussions on signal processing,
strain gage measurement, errors in measurement and transducers are presented, as well as
a tutorial outlining an application of the DASYLab data acquisition software.
The fourth section of this document presents the rationale for production of a
portable strain sensor to be used at the De Neveu Creek IBRC Bridge, research and
development resulting in the final configuration of the sensor for field implementation
204
and also laboratory validation of its performance. Finite element analysis models were
also developed to verify the performance of the sensors. Finally, individual calibration
factors for the sensors were determined, with the intention that they to be applied to field
collected data, producing reliable strain data for subsequent analysis.
A proposed load test of the De Neveu Creek IBRC Bridge is also outlined, to be
conducted in the spring of 2006. The objectives of live load testing are presented,
identifying locations of monitoring instruments on the bridge. The permanent equipment
required on the bridge is presented, as well as the proposed methods in which to load the
structure for live load testing. The data acquisition system to be used for the load is
described, with detailed recommendations outlining the operation of the strain gage
modules and transducer module. Recommendations as to the use of acquisition software
and probable errors found during acquisition are also detailed.
6.1 – Conclusions
The successful monitoring projects presented indicate that live load monitoring of
bridge structures is possible and may provide valuable insight into the performance of the
bridge. Identification of electrical resistance strain gages as the preferred live load data
acquisition instrument was completed, noting that vibrating-wire types lack the rapid
response required for short-term testing. Furthermore, it was determined that high-speed
data acquisition systems must be employed to properly capture the true strain response of
the structure. Of particular importance are the conclusions noted in reviewing the
previous load test of the De Neveu Creek IBRC Bridge. Girder distribution factors
205
(GDFs) based on deflection measurements were presented in section 2.3. These GDFs
are important as they provide a baseline for which to compare results from the proposed
load test. It is theorized that GDFs based on recorded strains from the proposed load test
will be similar to those values presented.
A number of conclusions were drawing in the arena of signal conditioning and
data acquisition. It was identified that high-speed acquisition systems satisfy the Nyquist
sampling theorem, as frequency response of bridge structures are typically quite low.
Use of both digital and analog filtering is warranted, as ambient noise introduced into
measurement signals creates significant uncertainty in measurements. The quarter bridge
Wheatstone bridge configuration was identified as the most accurate and cost-effective
configuration for measurement in this project. Also, shunt calibration was identified as
an adequate method of calibration, ensuring accurate measurements with quarter bridge
strain gages. Common sources of error in measurements were identified and determined
to have negligible effects on measurements proposed.
During development of the portable strain sensor, it was concluded that use of
high-modulus materials is inappropriate as a base material, as the imbalance of relative
stiffness between the sensor and measured structural component can create inaccurate
strain readings in the portable strain sensor configuration proposed. Additionally, the use
of epoxy or other adhesives as an attachment method was determined to be inappropriate
since commercially available adhesives tend to stretch and hinder strain transmission into
206
the sensor material. Thus, a mechanically anchored, low-modulus material was selected
for the portable strain sensors.
Determination of tensile and compressive calibration factors for each individual
sensor was also performed. It was concluded that individual factors are appropriate given
the predominantly linear behavior of the strain sensors under axial tension and
compression loading. Correction factors for field acquired strains are presented in
section 4.7.3.
6.2 – Recommendations for Future Research
Most notably, the completion of the proposed load test described in section 5 will
produce significant insight into behavior of the De Neveu Creek IBRC Bridge under
loading. Distribution of load to girders, distribution of wheel loads within the FRP-
reinforced deck, and determination of the degree of composite behavior of the bridge are
important topics regarding the structural performance of this bridge type and must be
evaluated. Additionally, completion of a successful load test would validate the in-field
performance of the portable strain sensors developed for this project.
Determination as to what an “appropriately low” stiffness for strain sensor carrier
material noted in section 4.2 is could be performed in a future analysis. Insight into the
behavior of a low-modulus sensor material when attempting to monitor strain on
concrete, steel or other higher modulus substrate is warranted.
207
While determined appropriate for calibration of the sensors used in this project,
the constant-moment test frame used occupies a large amount of space. Assembly of the
frame also requires a significant investment of time and labor. Exploration into
alternative calibration systems that are more compact and rapidly assembled is warranted
for future construction of sensors.
The modeling used to validate the performance of the constant-moment also has
room for improvement. The beam model constructed was, for all intensive purposes, a
detailed verification of beam theory. Further modeling of the beam used in the laboratory
should incorporate the bolt holes drilled for anchorage of the strain sensors. the use of
these holes in a beam model would provide further detail as to the strain field produced in
the beam model, yielding a model that more closely models the behavior of the test beam.
While commonly accepted material properties values were used for all materials
documented in this project, validation testing of the Nylon material to determine the
actual material properties would be beneficial. Results from this testing would allow for
more detailed finite element modeling of the sensors and produce a greater degree of
confidence in results. However, better modeling of the boundary conditions could be
done as well. For instance, the use of contact elements in the finite element modeling
could increase the accuracy of the models.
Additionally, a model of the constant-moment test frame could be constructed to
provide insight into the total system behavior. This could produce valuable information
208
as to validation of the behavior of both the test beam and the strain sensors and also
eliminate the occurrence of separate models, as was performed herein.
Investigation into other mechanical anchorage systems is also warranted. While
appropriate, the threaded-bolt system proposed within in this document requires a
significant amount of labor in the field and exploration of alternative systems would be
beneficial.
Further analysis into the behavior of the sensor model is also warranted. As noted
in section 4.6, the behavior of the sensor when under load involves multiple types of
response, which are theorized to interact with each other. Investigation into the behavior
between the washers used in the anchorage system and the Nylon sensors material and
the effect that bending has on the sensor is warranted. Also, analysis pertaining to the
effect that the significantly large sides of the sensor relative to the very thin “tub” of the
sensor bottom could provide additional benefit. Finally, detailed investigation into the
role that the strain relief notch (Figure 4.6.16) plays in sensor behavior would be
reasonable. The degree to which these noted scenarios affect the sensor’s performance is
unknown and thus justifiable.
Although it has been determined to be satisfactory for this project and used
throughout, the IOTech DaqBook data acquisition system with DBK43A and DBK65
modules presented many difficulties. Particularly, the DBK43A modules contain a high
degree of customizability, requiring the user to posses a detailed understanding of
209
electrical equipment and programming experience. Additionally, the DBK43A modules
purchased for this project did not perform as expected, requiring a great deal of
troubleshooting to resolve hardware issues. For example, voltage regulation of specific
channels the DBK43A modules were not selectable by the user and fixed at inappropriate
levels. Overall, the DaqBook system is a powerful data acquisition tool and use of the
system can provide valuable information, however, a detailed understanding of the
equipment and signal processing is required.
210
References
AASHTO. (1996). "LRFD Standard Specifications." American Association of State
Highway and Transportation Officials.
AASHTO. (1998). "LRFD Standard Specifications." American Association of State
Highway and Transportation Officials.
AISC. (2001). LRFD Manual of Steel Construction - 3rd Edition, American Institute of
Steel Construction, Chicago, IL.
ANSYS. (2005). "ANSYS University Intermediate, Release 10.0." ANSYS, Inc.,
Canonsburg, PA.
ASCE. (2005). "Report Card for America's Infrastructure." American Society of Civil
Engineers, Reston, VA.
Bank, L. C. (2005). "Personal communication via Email." Milwaukee, WI, Preliminary
Report on Load Testing of WI B-20148/149.
Bank, L. C., and Xi, Z. (1995). "Punching Shear Behavior of Pultruded FRP Grating
Reinforced Concrete Slabs." Non-metallic (FRP) Reinforcement for Concrete
Structures, 361-367.
Bank, L. C., Xi, Z., and Munley, E. "Performance of Doubly-Reinforced Pultruded
Grading/Concrete Slabs." Advanced Composite Materials in Bridges and
Structures, 351-360.
Bank, L. C., Xi, Z., and Munley, E. "Tests of Full-Size Pultruded FRP Grating
Reinforced Concrete Bridge Decks." Materials: Performance and Prevention of
Deficiencies and Failures, Atlanta, Georgia, 618-631.
BDI. (2005). Bridge Diagnostics Incorporated.
Bridge Diagnostics Inc. (2002). "Load Test and Rating Report - Fairground Road Bridge,
Greene County, Ohio."
Conachen, M. J. (2005). "Modular 3-D FRP Reinforcing System for a Bridge Deck in
Fond du Lac, Wisconsin," University of Wisconsin-Madison, Madison,
Wisconsin.
DASYLab. (2004). "DASYLab 8.0." DASYTech USA.
211
Dieter, D. A. (2002). "Experimental and Analytical Study of Concrete Bridge Decks
Constructed with FRP Stay-in-place Forms and FRP Grid Reinforcing,"
University of Wisconsin-Madison, Madison, WI.
Dietsche, J. S. (2002). "Development of Material Specifications for FRP Structural
Elements for the Reinforcing of a Concrete Bridge Deck," University of
Wisconsin-Madison, Madison, WI.
Farhey, D. N. (2005). "Bridge Instrumentation and Monitoring for Structural
Diagnostics." Structural Health Monitoring, 4(4), 301-318.
FHWA. (1996). "Implementation Program on High Performance Concrete - Guidelines
for Instrumentation of Bridges: FHWA-SA-96-075." Federal Highway
Administration.
FHWA. (2005). "IBRC Program Information,
http://ibrc.fhwa.dot.gov/know/program.cfm." FHWA, ed.
Fyfe. (2005). "Tyfo UC Composite Laminate Strip System." Fyfe Company, L.L.C., San
Diego, CA.
Gere, J. M. (2001). Mechanics of Materials, 5th Edition, Brooks Cole.
Grace, N. F., Navarre, F. C., Nacey, R. B., Bonus, W., and Collavino, L. (2002). "Design-
Construction of Bridge Street Bridge - First CFRP Bridge in the United States."
PCI Journal, 47(5), 20-35.
Grace, N. F., Roller, J. J., Nacey, R. B., Navarre, F. C., and Bonus, W. (2005). "Truck
Load Distribution Behavior of the Bridge St. Bridge, Southfield, Michigan." PCI
Journal, 50(2), 77-89.
IOTech. (2004). Signal Conditioning & PC-Based Data Acquisition Handbook, 3rd Ed.,
IO Tech, Inc., Cleveland, OH.
IOTech. (2005a). "DaqBook/2000 Series User's Manual." p/n 1121-0901, revision 2.0,
IOTech, Inc., Cleveland, OH.
IOTech. (2005b). "DBK Options, User's Manual Part 2 of 2." p/n 457-0912, revision 5.0,
IOTech, Inc., Cleveland, OH.
Jacobson, D. A. (2004). "Experimental and Analytical Study of Fiber Reinforced
Polymer (FRP) Grid-Reinforced Concrete Bridge Decking," University of
Wisconsin-Madison, Madison, WI.
212
Lenett, M. S., Hunt, V. J., Helmicki, A. J., and Aktan, A. E. (2001). "Instrumentation,
testing, and monitoring of a newly constructed reinforced concrete deck-on-steel
girder bridge- Phase III." UC-CII-01/1, University of Cincinnati, Cincinnati,
Ohio.
Micro-Measurements. (2004a). "Instruction Bulletin B-147-4." Application of M-Coat J
Protective Coating, Vishay Micro-Measurements, Revised March, 1996.
Micro-Measurements. (2004b). "Tech Note TN-507-1." Errors Due to Wheatstone Bridge
Nonlinearity, Vishay Micro-Measurements, Revised January 20, 2005.
Micro-Measurements. (2004c). "Tech Note TN-514." Shunt Calibration of Strain Gage
Instruments, Vishay Micro-Measurements, Revised December 5, 2004.
Micro-Measurements. (2005a). "Errors due to Leadwire Resistance." Vishay
Intertechnology, Inc.
Micro-Measurements. (2005b). "Tech Note TN-502." Optimizing Strain Gage Excitation
Levels, Vishay Micro-Measurements, Revised January 14, 2005.
Micro-Measurements. (2005c). "Tech Note TT-612." The Three-Wire Quarter Bridge
Circuit, Vishay Micro-Measurements, Revised January 20, 2005.
Mindess, S., Young, J. F., and Darwin, D. (2003). Concrete, 2nd Ed., Prentice Hall,
Pearson Education, Inc., Upper Saddle River, New Jersey.
MnDOT. (2005). "Pavement Sensors." Minnesota Department of Transportation.
National_Instruments. (2005). "AC and DC Coupling." National Instruments
Corporation.
NCHRP. (1998). "Research Results Digest #234 - Manual for Bridge Rating Through
Load Testing." National Cooperative Highway Research Program.
Omega. (2000). "Data Acquisition." Transactions in Measurement and Control, Putnam
Publishing Company and OMEGA Press, L.L.C.
Powers. (2005). "Specification and Design Manual - PowerFast+ Epoxy Adhesive
Anchoring System." Powers Fasteners, New Rochelle, NY.
Rizzoni, G. (2003). Principles and Applications of Electrical Engineering, 4th Ed.,
McGraw-Hill, New York.
ROMUS. (2005). "Strain Sensor Shop Drawings." ROMUS Incorporated, Milwaukee,
WI.
213
Schultz, J. L. (2005). "Personal Communication via Telephone." Milwaukee, WI, Bridge
Diagnostics, Inc. Initical Equipment Estimate.
Turner, M. K. (2003). "In-situ Evaluation of Demonstration GFRP Bridge Deck System
Installed on South Carolina Route S655," University of South Carolina.
UniMeasure. (2005). "PA Series Position Transducer Specifications." UniMeasure, Inc.,
Corvallis, OR.
WiDOT. (2003). "Construction Plans - City of Fond du Lac Bypass, USH 151, State
Project Number 1420-05-71." Structure B-20-148, State of Wisconsin Department
of Transportation.
Wikipedia.org. "Wheatstone Bridge." www.Wikipedia.org.
Ziemian, R. D., and McGuire, W. (2002). "Mastan 2, Version 2.0." John Wiley & Sons,
MATLAB-based Matrix Structural Analysis Program.
Appendix A – Partial Plan Set of the De Neveu Creek IBRC Bridge
214
262
215
263
216
264
217
265
218
266
219
267
220
268
221
269
222
270
223
271
224
272
225
273
226
274
227
275
228
276
229
277
230
278
231
279
232
280
233
281
234
Appendix B – Compressive and Tensile Shunt Calibration Calculations
235
Calculation of Voltage Drop Across Each Resistor:
Left Arm - IL
1000Vexec
Ra Rc+( )float 6, 3.57143→:= Right Arm - IR
1000Vexec
Rb Rd+( )float 6, 3.56633→:=
VA
IL Ra⋅
1000float 6, 1.25000→:= VB
IR Rb⋅
1000float 6, 1.25178→:=
VC
IL Rc⋅
1000float 6, 1.25000→:= VD
IR Rd⋅
1000float 6, 1.24822→:=
Initial Imbalance within the Circuit:
VAB 1000 VC VD−( )⋅ float 3, 1.78→:= mV
Also, Output Voltage can be Calculated Directly via:
VO 1000Rc
Ra Rc+
Rd
Rb Rd+−
Vexec⋅ float 3, 1.78→:= mV
mAITOTAL
1000Vexec
REQ
float 6, 7.13776→:=
ohms REQ1
1
Ra Rc+( )1
Rb Rd+( )+
float 8, 350.24982→:=
Tensile Configuration of Shunt ResistorEquivalent and Total Response of Entire Circuit:
Rshunt 64900:=Rb Rgage:=
Rd 350:=Rc 350:=
Rgage 351:=Ra 350:=
volts Vexec 2.500:=
Input Values (all resistances are in ohms):
Quarter Bridge Wheatstone Bridge
236
- Note that the left arm's voltages do not change as the voltage drop
across it remains constant at the prescribed voltage. However on the
right arm...
VA Va−( ) VC Vc−( )+ 0→
Vc
IlT Rc⋅
1000float 6, 1.25000→:=
Va
IlT Ra⋅
1000float 6, 1.25000→:=
IlT
1000Vexec
Ra Rc+( )float 6, 3.57143→:=Left Arm -
Calculation of Voltage Drop Across Each Resistor including Shunted Arm:
- This positive value makes sense as the decreased
equivalent resistance of the shunted circuit requires
that more current (recall V=IR) to balance the circuit
at the prescribed voltage.
µA, or microamps 1000 ITOTT ITOTAL−( ) float 3, 9.58→
Difference between Initial and Shunted Current Values:
mAITOTT
1000Vexec
REQT
float 6, 7.14734→:=
ohms REQT1
1
Ra Rc+( )1
Rb RCALT+( )+
float 8, 349.78051→:=
Shunted Resistance Values:
RCALT1
1
Rd
1
Rshunt
+
float 8, 348.12261→:=
Equivalent Resistance for the Shunted Arm (shunting of Rd, not the actual strain gage, simulates a
tensile strain):
SHUNT CALIBRATION OF A QUARTER BRIDGE CIRCUIT - TENSILE SIMULATION
237
...and as noted previously this positive change in voltage indicates a tensile
strain within the Wheatstone bridge.
mV VabT VAB− float 3, 3.36→
Difference between Initial and Shunted Values:
VoT 1000Vexec
Rc
Ra Rc+
RCALT
Rb RCALT+−
⋅ float 3, 5.14→:=
Which can also be Calculated Directly via,
mV VabT 1000 Vc VCALT−( )⋅ float 3, 5.14→:=
Shunted Imbalance within the Circuit:
VD 1.24822→VCALT
IrT RCALT⋅
1000float 6, 1.24486→:=
VB 1.25178→VbT
IrT Rb⋅
1000float 6, 1.25514→:=
SHUNTED VALUE -ORIGINAL VALUE -
IrT
1000Vexec
Rb RCALT+float 6, 3.57591→:=Right Arm -
...voltages do respond to the resistance change
across the shunted arm...
238
mV VabC 1000 Vc VdC−( )⋅ float 3, 1.59−→:=
Shunted Imbalance within the Circuit:
VD 1.24822→VdC
IrC Rd⋅
1000float 6, 1.25159→:=
VB 1.25178→Vcal
IrC Rcal⋅
1000float 6, 1.24841→:=
SHUNTED VALUE -ORIGINAL VALUE -
IrC
1000Vexec
Rcal Rd+float 6, 3.57597→:=Right Arm -
Calculation of voltages across shunted arm (recall that the non-shunted arm remains static):
- Note that both the compressive and tensile shunt
processes yield the same current flow through the
circuit!
mAITOTT 7.14734→
mAITOTC
1000Vexec
REQC
float 6, 7.14739→:=
ohms REQC1
1
Ra Rc+( )1
Rcal Rd+( )+
float 8, 349.77783→:=
Shunted Resistance Values:
Rcal1
1
Rb
1
Rshunt
+
float 8, 349.11189→:=
Equivalent Resistance for the Shunted Arm (direct shunting of the strain gage, Rb, simulates a
decrease in resistance and thus, a compressive strain):
SHUNT CALIBRATION OF A QUARTER BRIDGE CIRCUIT - COMPRESSIVE SIMULATION
239
Which can also be Calculated Directly,
VoC 1000Vexec
Rc
Ra Rc+
Rd
Rd Rcal+−
⋅ float 3, 1.59−→:=
Difference between Initial and Shunted Values:
VabC VAB− float 3, 3.37−→ mV
- The negative change in voltage simulates a compressive
strain within the Wheatstone bridge!
-Also, note that the magnitude of both tensile and compressive voltage changes
are approximately equal; the only real difference is their corresponding sign.
240
Appendix C – Final Configuration of the Portable Strain Sensor
241
VENDOR:
SHEET 1 OF 3
SCALE: 2:1
0.04
PART NO:
MATERIAL:
DESC:
FILE DATE:
WRITTEN PERMISSION OF ROMUS INC IS PROHIBITED.
5 4 3 2 1
DRAWN BY:WEIGHT:
Project:TITLE:
ROMUS INCROMUS INCROMUS INCROMUS INC
JPS
Wednesday, September 14, 2005 7:10:08 PMstrain-gauge-bisc
STAIN GAUGE BLOCK ASMSTGB
MU FOLEYClient:
FILE NAME:
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OFROMUS INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
NO:
242
0.110
SECTION B-B
0.010
0.200
0.250-0.010
+0.010
VENDOR:
SHEET 2 OF 3
SCALE: 2:1
0.04 NYLON 6/6 BLK
PART NO:
MATERIAL:
DESC:
FILE DATE:
WRITTEN PERMISSION OF ROMUS INC IS PROHIBITED.
5 4 3 2 1
DRAWN BY:WEIGHT:
Project:TITLE:
ROMUS INCROMUS INCROMUS INCROMUS INC
JPS
Wednesday, September 14, 2005 7:11:20 PMstrain-gauge-biscuit
STRAIN GAUGE MNTSTGB
MU FOLEYClient:
FILE NAME:
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OFROMUS INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
NO:
0.250
0.500
0.520
1.250
1.5000.386
4.003.000
2 x
1.00
B B
243
Appendix D – Simulated Tensile Strains used during Sensor Calibration
244
Sensor # Sensor #Test Top T/Resistance Bottom B/Resistance T/Shunt B/Shunt
1 1 350.4 2 350.8 2563 25592 2 351.0 1 350.9 2568 25603 3 350.8 4 351.0 2566 25614 4 351.0 3 350.8 2568 25595 5 351.1 6 350.9 2568 25606 6 350.6 5 351.4 2565 25637 7 350.9 8 351.3 2567 25638 8 351.4 7 351.2 2571 25629 9 350.8 11 351.0 2566 256110 11 350.7 9 351.0 2565 256111 10 350.6 12 350.7 2565 255812 12 350.7 10 350.5 2565 255713 13 350.8 14 350.7 2566 255814 14 350.8 13 350.5 2566 255715 15 350.8 16 351.2 2566 256216 16 351.3 15 350.8 2570 255917 17 351.1 18 351.2 2568 256218 18 351.3 17 350.8 2570 255919 19 351.0 20 351.1 2568 256120 20 350.5 19 351.1 2564 256121 21 350.6 22 351.3 2565 256322 22 351.4 21 350.7 2571 255823 23 351.0 24 350.6 2568 255824 24 350.8 23 351.2 2566 256225 25 350.6 26 350.5 2565 255726 26 350.6 25 350.6 2565 255827 27 351.4 28 350.9 2571 256028 28 350.9 27 351.2 2567 256229 29 350.6 30 351.3 2565 256330 30 351.3 29 350.7 2570 255831 31 350.7 32 350.6 2565 255832 32 350.8 31 350.8 2566 255933 33 350.7 34 351.1 2565 256134 34 351.2 33 350.6 2569 255835 35 350.8 - - 2566 -36 - - 35 350.7 - 2558
CALIBRATION TESTS - SHUNT VALUES
Sim. uStrain
245