dimensions specifications - gw becker inc crane training crane & runway installation ... -top...
TRANSCRIPT
Service
Trained and certified service technicians for expert maintenance and repair
Yale – Shawbox Factory Authorized Service Center
24-hour emergency service available
All welders certified to AWS D1.1 and D14.1
Crane Modernizations
Overhead Crane Training
Crane & Runway Installation
Runway Surveys and Inspections
Engineering Analysis
Hoist Inspection & Repair Service
Runway Repairs/Rail Replacement
Load Tests
Crane Installation
Inspections
In
Brake Wheels
Trained and Certified Overhead Crane Inspectors
OSHA compliant Periodic & Frequent Inspection Reports
Frequent Inspection – Daily to monthly intervals
Periodic Inspection – 1 to 12-month intervals
Electronic storage & access of Inspection Reports
Wheel Assemblies
Parts
Parts for all Makes & Models
Yale – Shawbox Master Parts Distributor
Component Rebuilds
Reverse Engineering Capabilities for Obsolete or Hard to Locate Parts
Your Overhead Lifting Single Source Provider
Lower Blocks
Custom Manufactured Cranes
Overhead Cranes
CMAA Member Company, OEM Integrated Crane Manufacturer
New Cranes, Hoists, Jibs and Workstations -Top Running Double Girder Cranes up to 200 tons / 150’ Spans Continuous Severe Service -Top Running Single Girder Cranes up to 30 tons / 125’ Spans Heavy Service
Gantry and Semi-Gantry Cranes Runway Designs and Fabrications
Automated Systems
Patented Track Systems
2600 Kirila Blvd. Hermitage, PA 16148 Toll Free (855) 4BECKER PH (724) 983-1000 FX (724) 983-1818
www.gwbcrane.com
Brake
Dia.
Specifications Dimensions
“D”
WHEEL
DIA.
“F”
FACE
WIDTH
“O”
HUB
OFFSET
“H”
HUB
LENGTH
“B”
BORE
DIA.
BORE
TAPER
IN/FT ON
DIA.
“S”
KEYWAY
WIDTH
“T”
KEYWAY
DEPTH
BORE AND KEYWAY MACHINING
For machining special wheel bores and keyways, give
complete shaft data.
For tapered shafts, don’t forget the “taper per foot” on diameter. Tapered bores will have a tolerance of -0.005 inch. The standard taper is 1.250 inches per foot on diameter.
For straight bores provide complete keyway dimensions and advise if gib key, or keeper plate will be used to hold wheel onto shaft.
For standard AISE-NEMA DC or AC wound rotor motors, only the motor information is required.
For NON-STANDARD motors and special wheels, please complete the specification sheet.
Standard straight bores are manufactured within a
tolerance of -0.001 inch. The keyway tolerance is +0.005
inch on the width and +0.016 inch on the depth.
Complete the specification section and contact us by phone, FAX or email for price and availability.
Phone (724) 983-1000 FAX (724) 983-1818 [email protected]
OPTIONAL FEATURES
Straight bore and keyway
Taper bore and keyway
Lockwasher slot
Special materials
Deep carburizing
Dynamic balancing
Non-destructive testing
Brake wheel couplings available upon request
STANDARD FEATURES
Manufactured from
ductile iron
Completely machined to
provide proper balance at
normal speeds
Resistant to scoring
Wears smoothly and
evenly
Good compatibility with
friction materials
Semi-finished with rough
pilot bore
An extra charge may be required for wheels that cannot be machined from the
standard wheel castings or for wheels that do not match the standard
electric/hydraulic brake wheels. Consult factory for pricing.
BALANCING CARBURIZING LOCKWASHER SLOT NON DESTRUCTIVE TESTING OTHER MATERIALS ______________ (SPECIFY)
Brake wheels for a 600 or 800 frame dc mill motor, Specify motor frame number.
OPTIONS
DIMENSIONS REQUIRED FOR ORDERING WHEELS
BASIC WHEEL DIMENSIONS
CRANES – PARTS – SERVICE – INSPECTIONS - TRAINING CRANES – PARTS – SERVICE – INSPECTIONS - TRAINING
Phone (724) 983-1000 Fax (724) 983-1818 [email protected]
H
H
H
H
O
H
F
H
O
H
F
H
B Tapered
Bore
B Tapered
Bore
Brake
Dia.
D