dissertation report false ceiling
TRANSCRIPT
-
8/9/2019 Dissertation Report False Ceiling
1/42
CHAPTER – 1
SYNOPSIS
1.1 INTRODUCTION -
A false ceiling is often a secondary ceiling hung below the main or structural ceiling, it
may also be referred to as drop ceiling. In the modern world, human life experience is
largely played out in interior spaces. We may love the out-of-doors for the sense of
open air and sky, for the escape it offers from life inside enclosure, but the very joy of
being outside reflects the reality that so much of life is spent inside.
he three major architectural elements of interior space are the floor, the walls and
the ceiling. Although out of our reach and not used in the series as the floor and walls
are, the ceiling plays an important vital role in shaping the interior space and limiting
its vertical dimension. It is the sheltering element of interior design offering both the
physical and the psychological protection for those beneath its canopy.
!eilings are formed by the underside of the roof structures. he ceiling materials can
be attached directly to the structural frame or be suspended from it. !eilings are often
the location of many building service elements, such as lighting, "#A! registers, fire
sprinklers, smoke detectors and signs. he separate design of each of these
elements or subsystems, as well as their total integration with the general ceiling
construction, is a major design activity.
In construction work interior spaces are sometimes said to have $no ceiling,$ meaning
that nothing special is done to create a ceiling-it is simply the unfinished, underside of
the overhead structure. %ore often, however& something is done, if nothing more than
some careful cleaning or painting of the underside of the overhead structure.
In many situations, a separate ceiling construction is developed, either attached
directly to, or suspended from, the overhead structure. hus a floor'ceiling or roof'
ceiling sandwich of sorts is created, and often encloses an interstitial space that is
used to contain various building service elements, such as wiring, piping, ducting and
minor e(uipment. he full design of this system and all of the contained elements is a
major integrated design problem.
In some ways, ceiling finishes represent a major opportunity for freedom of choice of
materials. here is a general lack of concern here for effects of contact wear& ceilings
are not walked on and are generally out of reach. )ragile materials can be used,although there is nothing wrong with hard, durable ones either.
1
-
8/9/2019 Dissertation Report False Ceiling
2/42
here are mainly three functions of false ceiling-
*. Interior !limatic !ontrol
+. Aesthetics
. Activity emand
HISTORY -
In view of the fact that the ceilings of the first shelters consisted merely of the
underside of whatever kept the elements out, it is probably safe to assume that their
design was given a little or no conscious thought. ince that time, whatever defines
the interior space overhead has been dealt with by the architects and designers in
one of two ways i.e. either by exposing or embellishing the structure beneath the roof,
or by hiding it. he beautiful exposed wood beams of the great halls of /nglish
!astles and stone arches of 0omanes(ue and 1othic !athedrals show how the
%edieval /uropeans used the structural elements of their buildings to enhance the
beauty of the interior space. o conceal a 1othic !athedral2s substructure, architects
either filled in the stone ceiling with brick and covered it with a wooden trussed roof,
or simply built a smaller, lighter roof just below the main one, creating a smooth
surface that could be painted or otherwise decorated. 3ater, plaster was applied
directly to the surfaces of vaulted ceilings, and then elaborately ornamented. he
eventeenth !entury )rench styles of 3ouis 4#, 3ouis 4#I, and 0ococo, whose
complex ornamentation was limited only by the media, materials and imaginations of
the artisans of the period, are all excellent examples of both approaches, such as
coffered ceilings, which alternate carved exposed beams with recessed plaster
surfaces in the spaces between.
According to )ernando 3ope5 the fresco is important because it is one of the earliest
examples of Italian 0enaissance art being imported to pain. It is also remarkable
because the fresco techni(ue -- watercolors painted on wet plaster -- was rare in
pain during this time period.
%ost likely, these reasons forced 6eter I in *789 to carry out additional works in the
cathedral which included the installation of a suspended ceiling.
According to the available data the first known use of the suspended glass ceiling
was in 6ost :ffice avings ;ank, #ienna in *98< =i.e. 6ost 0enaissance /urope>.
2
-
8/9/2019 Dissertation Report False Ceiling
3/42
he ceiling is suspended *< feet ? inches below the concrete roof of the church. his
blocks the second tier of windows, which can be seen from the outside. In *9+, the
church was ready for worship.
1.2 AIM -
he work aims to study all the new false ceiling materials that are used in modern
building systems.
1.3 OBJECTIVES -
o study different types of false ceiling systems.
o study different types of installations of false ceiling. o study different materials used in false ceiling.
o study sustainable materials and sustainable design.
1.4 SCOPE -
In the modern world, human life experience is largely played out in interior spaces.
We may love the out-of-doors for the sense of open air and sky, for the escape it
offers from life inside enclosure, but the very joy of being outside reflects the reality
that so much of life is spent inside.
1.5 LIMITATIONS -
he scope of work shall be limited to various design aspects, materials used and
construction details.
1.6 METHODOLOGY -
Assimilation of information and data from various sources.
*. 6rimary data @ case study, books.+. econdary data @ journals, e-books. ertiary data @ ime aver tandards
Internet
3
-
8/9/2019 Dissertation Report False Ceiling
4/42
CHAPTER-2
DEFINITION
uspended ceiling is basically a secondary ceiling consisting of suspension systems
which is created below the primary ceiling, that is, the main roof. It is provided for
aesthetical as well as for functional purpose such as to conceal the spilling wires and
crises-crossing service lines, air conditioning, lighting, acoustical and also for hiding
structural members and to provide insulation =thermal> and reduces volume. It plays
a vital role in interior design of any space whether it is residential, commercial or any
other public building. In many situations, the ceiling skin takes on further importance
beyond aesthetic, acoustical, or visual re(uirements. It can also be used to complete
an envelop that provides a fire- resistive rating to the structural members above.
ItBs used to conceal varied service lines C structural features, open pipes and wiring,
and air-conditioning ducts. It gives more options to use special lighting systems such
as cove lighting, wall washers, floating effects and so on.
)alse ceiling can be used to give thermal insulation for a given space. ;esides, those
going for effective sonic system especially in auditoriums, cinema halls or recording
studios can use them. here are basically three main types of false ceiling @
*. Wall-to-Wall false ceiling type is the commonly used
one. his is a straightforward ceiling with plane,
curved,domed or angular shaped forms connecting all
the four walls. %aterials mostly used in this category
are 6:6, gypsum board, thermocol, extruded
aluminium, plywood, wooden paneling and ceiling
tiles. P. 2.1 !" #$ !" F"%& C&''()
+. %odular ceiling comes in fixed si5es of panels thus accommodating the lightingsystem with the same, multiple or fractions of the modules. Acoustic tile is the best
example in this category. /ven extruded aluminium
strips can be brought under modular system. he
advantage in the modular system is the flexibility it
offers in terms of change in the lighting system. his
also offers flexibility to service ducts and pipes that run
below the primary ceiling without damaging the false
ceiling. P. 2.2 M$*+", C&''()
4
-
8/9/2019 Dissertation Report False Ceiling
5/42
. etached ceiling is a $part ceiling$ with or without
covering the primary ceiling. his type is mainly used
to play with the levels of the false ceiling, to provide
cove lighting, wall washers and floating effects on the
ceiling. %ost of the false ceiling materials are suitable
for this type of system. his system is creatively used,
especially at the exhibition galleries and showrooms P. 2.3 D"&* C&''()
using very unusual materials like fabrics and other similar kind of materials.
)alse ceiling is relatively easier to maintain in the long run if the right materials are
used. Avoid using the textured or porous materials especially at the non-air
conditioned space. his will accumulate dust in the longer run, thus creating difficulty
in maintenance. As far as possible, one should select the ceiling materials in such a
way that it can be painted at a later stage. Another important point to be considered is
that the space between false ceiling and the primary ceiling shall be completely
sealed off so that it becomes easier for maintenance. !hoosing the appropriate
material makes a lot of difference in enjoying the false ceiling. o do it the right
way.here are four ways in which a false ceiling can be constructed either attached to
or detached to the hori5ontal elements of the substructure, which usually consists of
either wood joists or steel beams. he method used depends on the design and
interval of spacing.
P. 2.4 T'/0&, C&''() P. 2.5 A$+%#'" T'& C&''()
5
-
8/9/2019 Dissertation Report False Ceiling
6/42
CHAPTER- 3
TYPES OF FALSE CEILINGS
!eilings are interior elements that basically have little to do with building enclosure.
"owever, the roof of any building is basically involved with the development of a
ceiling for a space beneath it. If a ceiling is separately constructed element, it
combines with the floor or roof above it to produce total construction element. #arious
properties @ such as acoustic treatment, fire separation and thermal flow resistance @
must be determined for the whole construction. here are basically four types of false
ceiling, namely -
3.1 UNFINISHED CEILINGS
3.2 DIRECTLY APPLIED CEILING FINISHES
3.3 SUSPENDED CEILINGS
3.4 INDEPENDENT CEILING CONSTRUCTION
3.1 UNFINISHED CEILINGS
paces are sometimes referred to as having no ceiling. his is technically true only
for outdoor, unroofed spaces. If a space is enclosed overhead it has a ceiling- bydictionary definition.
escribing a space as having no ceiling usually refers to the situation where no extra
effort is made to treat the underside of the structure overhead in terms of additional
construction. his is more accurately described as an unfinished ceiling.
/xposed structure sometimes present this situation. "owever, exposure may refer
basically to the form of the structure, and not necessarily to its raw, untreated
underside. A simple coat of paint is a finish in this case.
here are situations where the appearance of the underside of the overhead
construction is of little concern @ in storage rooms, e(uipment rooms, attic spaces,
and so on. "owever, appearance may not be the only concern. torage of ha5ardous
materials may re(uire a high fire rating for the overhead construction& noisy
e(uipment may indicate the need for a major sound barrier. !eilings have many
potential functions, including, of course, developing a more attractive view overhead.
6
-
8/9/2019 Dissertation Report False Ceiling
7/42
P. 3.1 U('('%&* C&''() P. 3.2 U('('%&* C&''()
3.2 DIRECTLY APPLIED CEILING FINISHES
In general, materials used to finish interior walls can also be used to finish ceilings. A
difference here is that ceilings are typically out of arm2s reach, and some materials
can be used here that would not endure where they can be routinely touched. In
addition, there is some difference in the re(uirement for attaching and supporting
elements in a hori5ontal position versus a vertical one.
In most cases, the simplest ceiling treatments are those made directly to the
overhead construction. A simple coating of paint, stain, or some texture-producing
material in a thick coating form is the easiest and most economical, if the underside of
the structure is simple in form. If there are a lot of beams, bridging, or trussing, a
Dsimple coating may become (uite laborious and marginally feasible. In such cases,
it is advisable to try to have structural elements prefinished to the desired degree
before they are installed.
If drywall, plaster, or some form of paneling is to be attached to an overhead
structure, the design of the structure must include this consideration. Additional dead
load, spacing of framing members, means of attachment, and the general
arrangements of the framing may result in some factors that influence the design of
the structure.
In some situations it may be necessary to develop a separate construction system for
the ceiling, even though it is directly attached to the overhead structure. If either the
spacing or the arrangement of overhead framing does not place framing members in
a location re(uired for ceiling units, some intermediate framing elements may be
re(uired. he difficulty of attaching some types of ceiling elements to particularframing elements may also re(uire this. In some cases, this may result in the use of
7
-
8/9/2019 Dissertation Report False Ceiling
8/42
ceiling framing that is similar in form to that used for suspended systems, with the
ceiling framing members directly attached to rather that suspended from, the
overhead structure.
P. 3.3 DIRECTLY APPLIED CEILING P. 3.4 DIRECTLY APPLIED CEILING
3.3 SUSPENDED CEILINGS
uspended ceilings occur when a separate ceiling construction is hung from the
overhead construction. his involves design considerations for the ceiling
construction, the suspending method, and the means for developing the suspension
from the structure overhead. his form of construction may be used for a number of
reasons, such asE
*. Feed for a lower ceiling. Where multiple interior spaces occur beneath a
general overhead structure, smaller rooms may re(uire lower ceilings.
+. esire for a ceiling for a ceiling form different from that of the underside of the
overhead structure.
. esire for ceiling materials that cannot be easily attached to the overhead
structure in a direct manner.
-
8/9/2019 Dissertation Report False Ceiling
9/42
;ecause they exist often to provide for service systems overhead, suspended ceilings
may need to provide for access to the elements of the enclosed services. his
sometimes favors the use of the priority, modular unit systems, whose surface units
are usually small and individually removable.
eparate ceiling constructions- whether suspended or directly- may serve various
purposes in addition to their basic ones forming and appearance modification. /ffects
on light, sound, and air movements in the spaces beneath them may be of concern.
;arrier functions relating to fire, sound transmission, thermal flow, or security may be
involved. :ptions for basic construction and surface finishes may be limited by such
re(uirements.
!eilings are typically the location for various overhead items, such as light fixtures,
"#A! elements, loudspeakers, signs, and decorations. )or some visual design
concerns, as well as the general controlled development of the whole overhead
construction, all of these items should be developed in an integrated manner.
ypes of uspended !eilings @
3.3.1 JOINTLESS SUSPENDED CEILING -
Goint less ceilings are made of in-situ construction. uch type of ceiling consists of a
wooden or a metal frame work suspended by metal supports or hangers fixed to the
roof. he ceiling finish may be made of large sheets of plaster boards or plaster
applied to metal lathing or sprayed materials. Goint less ceilings appear similar to the
direct ceilings.
P. 3.5 JOINTLESS SUSPENDED CEILING P. 3.6 JOINTLESS SUSPENDED CEILING
3.3.2 FRAME AND PANEL CEILINGS -
)ramed and panel ceilings are pre-fabricated in a factory and assembled on site. he
frame work of a frame and panel ceiling is similar to joint less ceiling consisting of a
9
-
8/9/2019 Dissertation Report False Ceiling
10/42
grid of steel or aluminium members suspended from the roof by metal hangers. he
underside of the ceiling is formed by small self-finished units he frame work of a
frame and panel ceiling may be either exposed or concealed.
P. 3. FRAME AND PANEL CEILING P. 3. FRAME AND PANEL CEILING
3.3.3 STRIPPED CEILINGS -
)rame and stripped ceilings are similar in construction to the frame and panel
ceilings. Inverted aluminium or steel sections are suspended from the roof by steel
wire hangers. 6anels in the form of flat aluminum or steel channel sections is fixed
with profiled strips finished in the factory.
P. 3. STRIPPED CEILING P. 3.1 STRIPPED CEILING
3.3.4 OPEN OR DETACHED CEILING SYSTEMS -
:pen ceilings consists of a series of vertically hanging strips or grids, which provide
the illusion of a surface. his illusion can be enhanced with more depth and close
spacing of the sections. he grid is hung from the roof by metal hangers. he
10
-
8/9/2019 Dissertation Report False Ceiling
11/42
underside of the ceiling is not covered. etached ceiling is a $part ceiling$ with or
without covering the primary ceiling.
his type is mainly used to play with the levels of the suspended ceiling, to provide
cove lighting, wall washers and floating effect on the ceiling. %ost of the suspended
ceiling materials are suitable for this type of system. his system is creatively used,
especially at the exhibition galleries and showrooms using very unusual materials like
fabrics and other similar kind of materials.
P. 3.11 OPEN OR DETACHED CEILING P. 3.12 OPEN OR DETACHED CEILING
3.4 INDEPENDENT CEILING CONSTRUCTIONIn some situations, ceiling may be developed with construction that is totally
independent of that overhead. his may simply be the practical means for achieving
the ceiling, or it may be necessary where the ceiling is a great distance below the
structure above it.
Where room si5es are small, wall construction permits it, a ceiling may be developed
with separate framing supported by the room walls. his framing may be (uite
modest, if it only needs to support the ceiling and does not provide a floor for the
space above it. 3ive loads for ceiling spaces with limited access are usually only *8
psf. pan limits may be derived from critical concerns for deflection rather than actual
load- carrying capacity.
)or some types of occupancies- notably speculative, commercial ones, such as
offices and shopping centers- use of independent interior wall and ceiling construction
allows an enhanced level of freedom and ease for modifications of the interior
spaces.
11
-
8/9/2019 Dissertation Report False Ceiling
12/42
P. 3.13 INDEPENDENT CEILING P. 3.14 INDEPENDENT CEILING
12
-
8/9/2019 Dissertation Report False Ceiling
13/42
CHAPTER- 4
TYPES OF INSTALLATIONS
4.1 DIRECTLY ATTACHED INSTALLATIONS -
!eilings may be developed by direct attachment of
surfacing material to the overhead structure. In
residential construction, drywall is ordinarily attached
directly to the underside of the closely spaced, light
wood rafters or floor joists.
irect attachment will yield the minimum total thickness
of the ceiling plus the overhead structure which is
generally more desirable with floor P. 4.1 D',&# A##"&* I(%#""#'$(%
constructionin multistory building,
as total floor height will be the least. "owever, it will also
provide the least interstitial space and may present
problems where considerable space re(uired for
building service elements, such as ducts and recessed
lighting fixtures. irectly attachment of ceilings will also
provide a direct reflection of the general overhead
structure @ not so much a problem with floors, but
possibly one with nonflat roof structure. P. 4.2 D',&# A##"&* I(%#""#'$(%
P. 4.3 D',&# A##"&* I(%#""#'$(%
13
-
8/9/2019 Dissertation Report False Ceiling
14/42
4.2 SEMI DIRECT OR FURRED INSTALLATIONS -
In this type the framing joists are larger
members that are spaced farther apart. hespacing between the joists varies between +<
inches to H8 inches.
If the drywall is attached directly to the main
joists, will tend to warp because the attachment
points are too far. )or such type of structures,
furring strips are installed as secondary P. 4.4 S&/' D',&# $, F+,,&* I(%#""#'$(%
upportive members to the main joists. hese members are attached to the main
joists at right angles. he spacing between two consecutive secondary joists may
vary between *H inches to +< inches apart.
If the main members are wooden then wooden
furring strips are attached to the main members
and if the main members are of metal W
sections then metal furring channels, or hat
channels, are wired to the bottom of the main
joists. he drywall is then attached to these P. 4.5 S&/' D',&# $, F+,,&* I(%#""#'$(%
furring strips. !eiling is not directly attached to the structural member above a
secondary framing for the ceiling is attached to the underside of the overhead
structure. It is used where the elements of the spanning structure are too widely
spaced for the ceiling materials.
4.3 SUSPENDED CEILING INSTALLATIONS -
In view of the number of elements that
re(uire space above the ceiling, which make it
difficult to successfully create a level surface
with either direct or semi direct installation,
the suspended ceiling is the most commonly
used false ceiling type in the interiors today.
P. 4.6 S+%7&(*&* C&''() I(%#""#'$(%
14
-
8/9/2019 Dissertation Report False Ceiling
15/42
A separate ceiling structure may be hung from the overhead structure, deriving
support from it but not necessarily reflecting its profile or detail. his is often done to
create needed space for e(uipment and services, but also to create a different form or
simply a lower ceiling level.
/ssentially, the suspended ceiling takes the basic furring grid and suspends it below
the elements that need to be covered. It allows the ceiling to be installed at almost
any height, as long as the hardware above has sufficient room.
)or instance, if the structure of the roof or the floor above is *? feet above the floor,
and the various hardware and system are * feet above the floor, the ceiling can
easily be installed at a height of *8 feet.
In addition, special shapes, angles and soffits can be created by merely hanging the
grid at an angle or by wiring the special shape into position.
uspension must be achieved with materials and details that relate to both the
overhead structure and the form of the ceiling construction.
ypical methods and materials used relate to common associations of structures and
ceiling constructions. )inally this type of ceiling can easily accommodate the variety of
items that must penetrate the ceiling surface, providing a platform for lights and air
diffusers.
P. 4. S+%7&(*&* C&''() I(%#""#'$(%
15
-
8/9/2019 Dissertation Report False Ceiling
16/42
4.4 SEPARATELY SUPPORTED INSTALLATIONS -
In some situations, ceilings may be
developed with construction that is totally
independent of that overhead. his maysimply be the practical means for achieving
the ceiling, or it may be necessary where the
ceiling is a great distance below the structure
above it.
Where room si5es arc small, and wall
construction permits it, a ceiling may be P. 4. S&7","#& S+77$,#&* I(%#""#'$(%
developed with separate framing supported by the room walls. his framing may be(uite modest, if it only needs to support the ceiling and does not provide for a floor for
the space above it. esign live loads for ceiling spaces with limited access are usually
only *8 psf. pan limits may be derived from critical concerns for deflection =visible
sag> rather than from actual load-carrying capacity.
)or some types of occupancies-notably speculative, commercial ones, such as offices
and stores-use of independent interior wall and ceiling construction allows an
increased level of freedom and ease for modification of interior spaces.
P. 4. S&7","#& S+77$,#&* I(%#""#'$(%
16
-
8/9/2019 Dissertation Report False Ceiling
17/42
CHAPTER- 5
MATERIALS USED IN FALSE CEILING
5.1 TIMBER CEILINGS
imber ceilings are a feature of older buildings and are beautiful when the grain of the
wood is exposed. hese usually have supporting members of thick sections of wood
that are transferred by smaller planks of wood or ply. he beams should either be
polished or varnished because paint will conceal the grain. A timber false ceiling is
usually made up of slats of wood that are fitted together using a tongue and groove
joint. 3ights may be inserted into the slats if re(uired.
P. 5.1 T'/0&, C&''() P. 5.2 T'/0&, C&''()
5.2 GYPSUM BOARD CEILINGS
1ypsum ;oard provides an uninterrupted ceiling surface which can be finished
smooth. he finished surface can easily be given some texture. he surface can also
be painted or even wallpapered. he gypsum board panels re(uire a supporting
framework of wood or metal which is attached to or suspended from the roof or floor
framing.
P. 5.3 G7%+/ B$",* C&''() P. 5.4 G7%+/ B$",* C&''()
17
-
8/9/2019 Dissertation Report False Ceiling
18/42
5.3 PLASTER OF PARIS CEILINGS
he most common false ceilings are made of 6laster of 6aris sheets that are
suspended on a galvani5ed iron framework. his is non-structural and does not take
any weight. !ommon applications include surgical rooms, clinically clean rooms,
curved detailing or intricate design. 6lasterboard suspended ceilings provide clean
uninterrupted lines with the appearance of plain flat finish creating a completely
sealed unit, which can then be individuali5ed with the use of color. A plain surface can
be embellished with cornices& embossing and other detailing that is moulded to one2s
specifications. hese details can then be painted different colors or gilded as
according to design.6laster can also be used to create a rough texture on ceilings @any tool can be used
to form a pattern of your choice. his type of installation is however restrictive in that it
is difficult to retro fit or alter any services installed into the ceiling void. Jsed
extensively in shop fit-out projects. Architects are demanding ever more eye-catching
features to foyers, reception and entrance areas. 6lasterboard on a metal or wooded
substrate provides a cost effective solution to these re(uirements.
P. 5.5 P"%#&, $ P",'% C&''() P. 5.6 P"%#&, $ P",'% C&''()
5.4 METAL CEILINGS
ecorative stamped metal panel ceilings were very popular in the early *988Bs. hey
were commonly used in commercial and retail buildings because of their uni(ue
appearance, low maintenance and fire resistance. If painted thoroughly on both sides,
these ceilings will literally last forever.
%etal ceiling panels are typically available in + ft. x + ft. s(uares and + ft. x < ft. or ? ft.rectangles. here are many patterns available, some from the original *88-year-old
18
-
8/9/2019 Dissertation Report False Ceiling
19/42
dies and other newer patterns. If you are a creative person, you can make a truly
uni(ue ceiling by using various combinations of patterns, cornice and crown
moldings, medallions, etc.
%ost metal ceiling panels are made of fairly thin steel sheet which is painted. )or a
more decorative and uni(ue appearance, an experienced painter can use two
different colors to highlight the surface texture. olid copper and brass panels are
also available, but they cost about three times as much as the steel.
It is not difficult to install metal ceiling panels. )irst, you should install ' ceiling. he standard si5e metal
panels usually will fit perfectly into a standard suspended ceiling support grid pattern.
It is best to leave the existing fiber panels in place over the thin metal panels. hese
help to keep the metal panels flat and stop the panels from moving =floating> from
bree5es from windows or when a door closes.
)or a very attractive installation, use a suspended grid system especially made for
these metal panels. hese grid members are very slim and some can even be hidden
by the edge of the ceiling panel to create a seamless appearance.
P. 5. M" C&''() P. 5. M" C&''()
19
-
8/9/2019 Dissertation Report False Ceiling
20/42
5.5 ALUMINIUM PANEL CEILINGS
A number of commercial and industrial interiors have metal ceilings. hese are
usually moulded aluminium panels or strips that fit together. hese are fabricated tofacilitate wiring and lighting. hese are available in a variety of finishes@powder
coated, perforated, brushed or ribbed. hese are expensive but (uick to install and
easy to maintain. he look is hi-tech, sleek and modern.
P. 5. A+/'(+/ P"(& P. 5.1 A+/'(+/ P"(& C&''()
5.6 GLASS CEILINGS
tained, colored or etched glass panels can be used in ceilings. hese can add
vitality to a restaurant or store especially if lit from above. !ommon applications
include clinical washrooms, kitchen areas, cleaning rooms, public rooms, and
swimming pools, in general, areas with high relative humidity. his type of ceiling
provides a washable ceiling, which still have superb decorative and acoustic (ualities.
kylights can also be inserted into a structural system to allow light. hese can be
made using fiberglass, acrylics or toughened glass. %irror chips can be inserted into
plaster as a dramatic flourish.
20
-
8/9/2019 Dissertation Report False Ceiling
21/42
-
8/9/2019 Dissertation Report False Ceiling
22/42
can have interesting murals or collages on the ceiling may be a mobile can be part of
the dLcor. :ne can also attach stars and the moon in metallic finishes to the ceiling.
P. 5.1 F"0,' C&''() P. 5.1 F"0,' C&''()
5. STRETCHED CEILINGS
his is one of the latest suspended ceiling system products and allows for the most
spectacular designs and colour not possible with more conventional systems. A
stretched ceiling system is basically a stretched plastic sheet ceiling fitted to a simple
support system. It is jointed with ultrasonic flush weld joints, which are almost
invisible. he end result is something (uite fantastic and very individual.
P. 5.1 S#,&* C&''() P. 5.2 S#,&* C&''()
5.1 GREEN MATERIALS
5.1.1 SUSTAINABLE DESIGN -
ustainability has become a fundamental principle underlying successful building
design. )rom a global stand point, ustainability is imperative as it offers a critically
important means for conserving our dwindling natural resources. )rom an architec-
tural standpoint, itBs becoming an increasingly important consideration, as a growing
22
-
8/9/2019 Dissertation Report False Ceiling
23/42
percentage of building owners and homeowners not only desire $green$ buildings, but
are now demanding them.
1reen has, in fact, gone main stream. Architects are giving high priority to
environmental concerns in their product selection, builders and developers are
acutely aware of how sustainability can impact project success and retailers are
proactively promoting green products.
espite its growing acceptance, sustainable building design remains a complex
undertaking. ;ecause environmental issues can - and should - be considered in
virtually every aspect of the design process, specifies need to have a working
knowledge of a wide range of green definitions, criteria, standards and applications.
ustainability is a long-term evaluation of every decision made, without compromise
to future generations.
5.1.2 GREEN MATERIAL SELECTION -
1reen material selection is a key component of sustainable design. "owever,
sustainable design should also encompass life-cycle analysis, product durability,
embodied energy, the effect on indoor environmental (uality, manufacturing locations
and the companyBs environmental record and commitment. In general, green
materials have traditionally been defined as those that reduce, recycle and renew.
pecifically, sustainable productsE -
0educe the amount of raw materials and'or the amount of energy needed.
3ighter products generally re(uire the use of less energy for transportation,
storage and construction. he term $reduce$ can also refer to decreasing the
amount of material used and'or wasted, thereby fostering manufacturing
efficiencies and optimal use of the material.
:ffer high recycled content and'or environmental friendly reuses. he benefits
here are obvious. 6roducts with a high recycled content may decrease raw
material usage, energy consumption and landfill waste. $0ecycle$ can also
refer to the potential of a product being remade into that product again or into
another product as in adaptive reuse =closing the loop>.
0enew the environment by using materials that can be regenerated and'or
materials offering environmental friendly benefits& including renewable
resources such as agriculture based materials or products made without
chemically bound methods.
23
-
8/9/2019 Dissertation Report False Ceiling
24/42
5.1.3 RECAPTURED GYPSUM -
%ost construction papers are made from the wood industryBs leftovers, which include
cardboard cut-offs or post-consumer papers =usually newspapers, catalogs or phone
books>. he face papers used on gypsum panels are *88 percent recycled paper, and
some manufacturers started using recycled paper as early as the *9H8s. As for the
core material, which is primarily gypsum, air and starch, many manufacturers use a
by-product gypsum source obtained from coal-burning power plants.
he coal burned in many of these power plants produces undesirable air pollutants,
including sulfur dioxide. Wet limestone scrubbers are often used to prevent this
pollution from entering the atmosphere. As the exhaust smoke from the power plant
rises through the scrubber, its pollutants are chemically removed. he calcium and
water in the wet limestone combine with the sulfur dioxide to create calcium sulfate,
or recaptured =flue-gas desulfuri5ed> gypsum.
%anufactured from 9 percent recycled materials, the high-performance gypsum fiber
products available include interior wall panels, ceiling boards.
!eiling board manufactured from recaptured gypsum is indistinguishable in terms of
performance, appearance and (uality from panels made from natural gypsum rock..
5.1.4 GYPSUM BOARD PANELS -
1ypsum, the primary raw material used to make gypsum panels, forms naturally like
salt or limestone, and is one of the most abundant minerals on the planet. It is neither
rare nor endangered. he bulk of the remaining materials is gypsum board consist of
paper =recycled from newspapers, phone books, or corrugated cartons and cardboard
cuttings> and corn or wheat starch binders. hese starch binders, which serve as the
$glue$ in the manufacturing process, are renewable agricultural resources.
he embodied energy of gypsum board is extremely low =see chart below>. rywall
has less embodied energy than a wide variety of building products, including
brickwork, concrete, particle board, insulation, glass, vinyl flooring, plastics, steel and
aluminum.
!onstruction waste gypsum panels can be reground and made into new gypsum
panels when the paper is removed. his waste can also be used for many other
functions, including agricultural uses or concrete set material.
:ther reuses for drywall include its addition as a soil amendment =using gypsum as a
high-calcium fertili5er or as a method for treating high soil p">, neutrali5ing the high
24
-
8/9/2019 Dissertation Report False Ceiling
25/42
p" levels caused by road salt applications, odor treatment and concrete setting
agent. he majority of this waste is from new construction cut-offs =about H million
tons>. !urrently, more than million tonsB of gypsum are used as soil amendments
annually and another < million tonsB are used as concrete setting agents.
P. 5.21 G7%+/ B$",* P. 5.22 G7%+/ B$",* P"(& C&''()
5.1.5 CEMENT BOARD PANELS -
!ement board, a water-durable, multiuse panel commonly used as a backer for
ceramic tile, is made from approximately +8 percent recycled materials =fly ash>. )ly
ash is another waste stream material from power plant emission control processes
that features cement-like properties. It is produced by electrical power companies in
the combustion of coal and other solid fuels, and is subse(uently purchased byconcrete and cement board producers for use as an aggregate.
All products impact the environment, and the key is to reduce this impact as a goal of
sustainable design. It is very important to look at the cumulative effect a material and
its constituent components or processes may have on the environment, both currently
and in the future.
P. 5.23 C&/&(# B$",* P. 5.24 C&/&(# B$",* P"(& C&''()
25
-
8/9/2019 Dissertation Report False Ceiling
26/42
CHAPTER- 6
INTEGRATED CEILINGS
Integrated ceilings are modular systems in which all ceiling components =lighting,
diffusers and finish> ideally are supplied by one manufacturer to provide visible
integration and functional continuity in the finish ceiling. hey are most commonly
used in conjunction with an open office plan and in malls, atriums, and other open
areas.
P. 6.1 I(#&),"#&* C&''() P. 6.2 I(#&),"#&* C&''()
6.1 TYPES OF INTEGRATED CEILINGS8 -
here are two types of integrated ceilings availableE-
1. THE GRID TYPE with lay in acoustical panels
2. LINEAR TYPE composed of spliced sections of metal pans or planks.
;oth involve a close relationship between mechanical and interior and re(uire careful
coordination of these systems. Integrated ceilings are usually bid as a package, and it
is very difficult to delete the components in the shop drawing phase. !are must also
be taken that esthetics is not emphasi5ed to the detriment of performance.
LIGHT FI9TURES - ype and placement should be determined based on the number
of watts per s(uare foot re(uired. %ost types of light fixtures can be incorporated in
an integrated ceiling assembly.
DIFFUSERS - Integrated ceilings commonly employ linear diffusers connected to the
ducts by means of a metal or fiberglass boot or manifold. he unused portion of the
diffuser is masked or blocked above the ceiling.
In the grid type of ceiling the finished appearance is that of a continuous diffuser in
the suspension grid, while the linear ceilings incorporate the diffusers between the
26
-
8/9/2019 Dissertation Report False Ceiling
27/42
metals pans.
PANELS - he type of acoustical panel chosen for a grid ceiling has a profound effect
on its appearance and performance. he panel types vary from traditional flat lay-in
panels to vaulted or coffered fiberglass forms and vinyl-faced batt insulation.
METAL SPANS - hese are typically < to H in. wide. hey are available in aluminum
and steel, the latter being less expensive, and come in a wide variety of finishes and
colors.
COST - Integrated ceilings can be very cost-effective and provide excellent service if
properly designed and used.
hese systems work best when used within open spaces. It should be borne in mind
that in order for the ceiling to be most cost-effective, all components should be
supplied by one manufacturer. !omponents by different manufacturers can and
fre(uently are used in integrated ceiling systems, but compatibility problems can arise
and cost-effectiveness is decreased.
CEILING TYPE - he configuration and material of the acoustical panels or metal
pans have a direct bearing on the acoustical and illumination factors in the space.
he grid type of ceiling can be customi5ed to fit an enclosed office but the problems of
closure when finishing off field-cut metal pans make the linear type difficult to use with
partitions.
6.2 ADVANTAGES OF LINEAR TYPE SYSTEM -
he advantages of the linear type of systems are as follows @
*. his type of system can be easily formed in curves or other forms according
to the design re(uirements.
+. It is available in a wide range of colors.
. It can be used on the exterior if visual continuity is desired at a soffit.
-
8/9/2019 Dissertation Report False Ceiling
28/42
MAINTENENCE -
An integrated ceiling is not as much difficult to maintain as it is in case of a
conventional suspended ceiling. In the grid type moisture-resistant or soil-resistant
panels should be used in the same as they would be in a conventional suspended
ceiling. he metal pans used in the linear type dent easily, and should be located out
of reach.
ACOUSTICAL PERFORMANCE -
In the panel or pan material should have a high noise reduction coefficient =F0!> to
cut down on reflected sound. In spaces with solid partitions, a ceiling material with a
low sound transmission coefficient =!> should be used to prevent sound transfer to
adjacent rooms. In open office plans, electronic sound masking is usually desirable.
#arieties of insulating material are available for use above the ceiling, and are
especially useful with metal pans. he most commonly used types are unfaced or
black faced fiberglass bats and semi rigid mineral board. %etal pans may also be
perforated to enhance the acoustical performance.
FIRE RESISTANCE -
While each component of an integrated ceiling may be fire-rated, very few systems
are classified as J3 fire-rated assemblies. Where a fire rated assembly is re(uired by
code, an integrated ceiling is probably not a good choice since the spacing, si5e. and
degree of penetrations are severely restricted and must be duplicated exactly in a
rated assembly. prinkler penetrations, if any, must also be part of the system.
RESISTANCE TO SMO:E -
!avity barriers are primarily intended to delay the passage of fire. here are no
specific tandard test criteria for resistance to the passage of smoke. "owever,
indicative tests have shown that mineral wool, reinforced with a +mm wire mesh,
acts as a high efficiency filter to prevent the passage of smoke particles.
)or applications where a particularly high standard of resistance to smoke or fumes is
re(uired, then a foil faced cavity barrier should be used. imilarly, a foil faced cavity
barrier may also be considered necessary in air plenums.
28
-
8/9/2019 Dissertation Report False Ceiling
29/42
FIRE SPREADING AND LINING MATERIALS -
he void created between the ceiling and the soffit of the structural floor is often
utili5ed to carry building services, but it will also provide a route for smoke and fire
transfer in the event of a fire.
he choice of materials for the lining of walls and ceilings can significantly affect the
spread of a fire, and its rate of growth, even though they are not likely to be the
materials first ignited. his is particularly important in circulation spaces where linings
would offer the main vehicle for fire spread, and where rapid spread would be most
likely to prevent occupants from escaping.
everal properties of lining materials influence fire spread. hese include the ease of
ignition and the rate at which the lining material gives off heat when burning. he
guidance relating to the fire tests and classification provides for control of internal fire
spread through control of these properties.
FIRE RESISTING CEILINGS8 -
he need for cavity barriers in concealed floor or roof spaces can be reduced by the
use of a fire-resisting ceiling below the cavity.
uch a ceiling should comply with the followingE -
=a> It should have at least 8 minutes of fire resistance.
=b> It should be imperforate except for an opening allowed under par.
=c> It should extend throughout the building or compartment.
=d> It should not be demountable.
29
-
8/9/2019 Dissertation Report False Ceiling
30/42
CHAPTER-
FALSE CEILINGS FOR ACOUSTICAL INSULATION
.1 ACOUSTICAL INSULATION -
he void above a suspended ceiling is a potential route for flanking sound above
partitions. his is especially true where a lightweight, modular ceiling is installed.
he sound absorbent characteristics of mineral wool can be employed to minimi5e
the Macoustic weaknesses of suspended ceilings by installing mineral wool cavity
barriers above partitions. %ineral wool can also be used to provide acoustic
absorbency at ceiling level, and so reduce the reverberation time in the room below.
.2 SOUND ABSORBENT CAVITY BARRIERS -
here are many situations, such as hospital consulting rooms, where it is important
that the sound performance of a partition is not compromised by the void above the
suspended ceiling. In these cases, a mineral wool cavity barrier, in combination with
the suspended ceiling, can limit flanking sound. o achieve the sound reduction, the
partition must have at least the same level of sound insulation as the cavity barrier
and ceiling.
P. .1 S$+(* A0%$,0&(# C";'# B",,'&, P. .2 S$+(* A0%$,0&(# C";'# B",,'&,
.3 PERFORATED METAL CEILINGS -
"igh degrees of sound absorption can be achieved using perforated or slotted panels
with a mineral wool backing. he presence of an air space above a suspended ceiling
or behind a wall lining greatly increases the absorption value of the mineral wool
30
-
8/9/2019 Dissertation Report False Ceiling
31/42
backing. Although mineral wool directly above a perforated metal ceiling will help to
reduce flanking sound, this form of construction is mainly used to reduce the
reverberant noise within a room or area.
.4 SOUND ABSORPTION -
ound absorption refers to the attenuation of reverberant noise within the same room
or area as the noise source. his normally involves lining all or part of the room
surfaces with a material which absorbs sound.
When a sound wave hits a surface, some of its energy will be reflected and some will
be absorbed. A material2s ability to absorb sound efficiently can be gauged from its
sound absorption coefficient, which is defined as the ratio of the sound energy
absorbed to the sound energy incident. A material, which absorbs HN of the sound
energy striking it, has a sound absorption coefficient of 8.H.
1lass mineral wool and rock mineral wool have e(ually good sound absorption
characteristics due to their fibrous nature, making mineral wool ideal as a sound
absorption layer.
.5 ACOUSTIC MINERAL !OOL -
Acoustic %ineral Wool consists mainly of silicon oxide together with a number of other
metallic oxides. It is non-flammable, chemically inert and is not adversely affected by
any substance it may come into contact with. 0andom arrangement of fibers ensures
no water penetration in any direction. It is rot-proof, non-hygroscopic, does not
sustain vermin and will not encourage the growth of fungi, moulds or bacteria. It will
not react with wired plastic or metal wall ties, brickwork or masonry.
he density of Acoustic %ineral Wool is more than twice that of normal loft
insulation and so is very efficient at absorbing noise. Acoustic %ineral Wool
is used extensively in buildings and throughout industry to give acoustic,
thermal and fire insulation. It is particularly useful as a sound absorbing infill
for the reduction of airborne sound between flooring joists, suspended ceilings,
stud partitioning and with our 0esilient ;ars. It is available in different thicknesses i.e.
+ mm, 8 mm, 7 mm, *88 mm etc =i5e H88 mm 4*+88 mm>.
31
-
8/9/2019 Dissertation Report False Ceiling
32/42
P. .3 A$+%#' M'(&," !$$ C&''() P. .4 A$+%#' M'(&," !$$
FEATURES OF ACOUSTICAL MINERAL !OOL -
*. )or effective reduction of airborne noise through floors and walls.
+. Acoustic infill between floor'ceiling joists. Acoustic infill for stud partitions
-
8/9/2019 Dissertation Report False Ceiling
33/42
CHAPTER-
INSTALLATION OF FALSE CEILING
)ollowing are the steps and instructions on how to install a )alse !eiling.
STEP – 1 6lanning for a )alse !eiling
STEP – 2 Installing Wall Angles
STEP – 3 3ocating and "anging uspension Wires for %ain ees
STEP – 4 Installing %ain ees
STEP – 5 Installing !ross ees and ;order !ross ees
STEP – 6 Installing !eiling 6anels
STEP – 1 PLANNING FOR A SUSPENDED CEILING
)irst, get the exact measurements of the room
where the suspended ceiling will be installed. Jse
special care in measuring any odd-shaped
alcoves, bays, etc.
raw the exact dimensions to scale on graph
paper.
he pattern you pick will determine the material P. .1 PLANNING FOR SUSPENDED CEILING
re(uirements for your ceiling.
)or the +x< pattern, decide whether you want to
install the patterns in a standard or reverse pattern.
/ach pattern offers a different appearance.
ketch the layout for the planned ceiling on graph
paper.
raw the main tees
-
8/9/2019 Dissertation Report False Ceiling
34/42
If you are using a +Bx
-
8/9/2019 Dissertation Report False Ceiling
35/42
STEP – 3 LOCATING < HANGING SUSPENSION !IRES FOR MAIN
TEES
If you are going to use recessed lights, install the wiring
before putting the suspension wires in place. )or
recessed lighting, you can use +x + or +x < drop-in
lighting fixtures, which are specially designed for this
purpose. Oou can also center fluorescent light fixtures
over the panels and use a luminous lay-in panel instead
of a regular ceiling panel. hese lay-in panels now
come in several attractive designs.
0efer to your sketch of the room for the location of all P. .5 SUSPENSION !IRES
main tees. %ain tees should always run at right angles to the joists in the room.
3ocate the position of each main tee by stretching a tight line from the top edge of the
wall angle on all sides of the room at each position
where the main tees are to be placed.
tretch a tight line from top edge of the wall angle on
all sides of the room at each position where the teesare to be placed.
Fow, cut the suspension wires to the proper length.
he wires should be *+$ longer than the distance
between the old ceiling and the new guideline string P. .6 LOCATING SUSPENSION !IRES
you have stretched to indicate the position of each main tee.
3ocate the first suspension wire for each main tee directly above the point where the
first cross tee meets the main tee. !heck your original
sketch of the room to determine this location. ;e sure
the suspension wires are securely fastened. Apply them
to the ceiling with screw eyes, screw hooks, nails, or
drilling.
Attach a suspension wire every
-
8/9/2019 Dissertation Report False Ceiling
36/42
STEP – 4 INSTALLING MAIN TEES
%ost main tees are *+B long and have
cross tee slots punched every*+$beginning H$ from each end.
0efer to your layout sheet to determine
the distance from the wall to the first
cross tee. Fow measure this distance
along the top flange of the main tee and
locate the slot just beyond this point. P. . INSTALLING MAIN TEES
)rom this slot, measure back the same distance, subtract *'?$ and saw the main tee
at that point. he *'?$ subtraction is for
the thickness of the wall angle.
If the wall angles are not s(uare,
position the cross tee slots accordingly.
When main tees are installed in rooms
less than *+B across, cut the main tee to
the exact measurement of the room,
allowing *'?$ for the thickness of the wall angle. P. . INSTALLING MAIN TEES
)or rooms wider than *+B, the main tee can be spliced.
;e sure to align the splice so that the
suspension wires are correctly
positioned. plice carefully, or all the
main tees will be thrown off.
Install the main tees so that they are all
level with the wall angle already
mounted. Jse a long level for this.
P. .1 INSTALLING MAIN TEES
STEP – 5 INSTALLING CROSS TEES < BORDER CROSS TEES
Install the cross tees by inserting the ends of the cross tees into the slots in the main
tees.
36
-
8/9/2019 Dissertation Report False Ceiling
37/42
etermine the location of the cross tees by the pattern you selected@either +Bx+B or
+Bx
-
8/9/2019 Dissertation Report False Ceiling
38/42
BOO: CASE STUDY
DUBAI HYATT HOTEL
Dubai, United Arab Emirates
ARCHITECTURE –
3D= I(#&,("#'$("
In ubai, one of the Jnited Arab/mirates on the 6ersian 1ulf, the"yatt hotel chain decreed a subtlepleasure-dome- an DArabian-nightsclub for drinking, dancing, and dinner conversation.
"yatt built an entire hotel complexbased on plans developed by'International, Inc, of "ouston,exas. 'I was also commissionedby "yatt to design the hotel2sinteriors, including the in-housenightclub interior, "yatt instructed'I to create an environment with a P. .1 DUBAI HYATT HOTEL CEILINGflavor Dnot too gaudy, not too disco.;ecause most patrons of the club would be American or audi businessmen, "yattasked that the ambience be Dsimilar to, but more romantic that their accustomed
gathering places back home.'I laid out a conventional foot-print for the club2s approximately ,888 s(uare feet,providing table and seating room for *8, a dance floor, and a small stage for revues.'I then treated the walls and privacy partitions unconventionally, wrapping them in adark blue fabric meant to recall the sea.o suggest the clear, sparkling sky of the desert night on the club2s ceiling, 'I againhad recourse to fabric. his time it was used in a more frankly romantic manner- threecascading swags of gossamer ol-0-#eil =a panne cloth of polyester> were looselystretched and draped over the width of the club. /ach swag was laterally stitchedtogether from the manufacturer2s *7- inch widths.teel grommets are sewn, at 8- centimeter intervals, into each hori5ontal swag hem.
he hems are fastened over eyehooks welded to the steel-tube-and-pipe supportsystem =wall support& intermediate support>. he support system includes a slot-and-screw slide mechanism to adjust tension in the swags.he technical specifications of the fabric areE *.
CHAPTER- 1
38
-
8/9/2019 Dissertation Report False Ceiling
39/42
-
8/9/2019 Dissertation Report False Ceiling
40/42
-
8/9/2019 Dissertation Report False Ceiling
41/42
*. httpE''www.archiexpo.com'prod'decibel-france'acoustic-ceiling-tiles-in-melamine-
?+88-7??++.html
+. httpE''www.archiexpo.com'prod'decoustics'acoustic-tiles-for-suspended-ceiling-
9?7-+?7H89.html
. httpE''www.sae.edu'referenceQmaterial'audio'pages'Walls.htm
-
8/9/2019 Dissertation Report False Ceiling
42/42