dn 70400137

7/28/2019 Dn 70400137

http://slidepdf.com/reader/full/dn-70400137 1/17

Nokia Siemens Networks

WCDMA RNC Rel. RN6.0, Site

Documentation, Issue 01

Unpacking IPA2800 Cabinets

DN70400137

Issue 3-0

Confidential

7/28/2019 Dn 70400137


2 DN70400137

Issue 3-0


Id:0900d805805a3251

Confidential

The information in this document is subject to change without notice and describes only the

product defined in the introduction of this documentation. This documentation is intended for the

use of Nokia Siemens Networks customers only for the purposes of the agreement under whichthe document is submitted, and no part of it may be used, reproduced, modified or transmitted

in any form or means without the prior written permission of Nokia Siemens Networks. The

documentation has been prepared to be used by professional and properly trained personnel,

and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes

customer comments as part of the process of continuous development and improvement of the

documentation.

The information or statements given in this documentation concerning the suitability, capacity,

or performance of the mentioned hardware or software products are given "as is" and all liability

arising in connection with such hardware or software products shall be defined conclusively and

finally in a separate agreement between Nokia Siemens Networks and the customer. However,

Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions

contained in the document are adequate and free of material errors and omissions. Nokia

Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which

may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO

EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-

TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-

RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED

TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY

OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION

IN IT.

This documentation and the product it describes are considered protected by copyrights and

other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark

of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respectiveowners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2011. All rights reserved

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources

of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle

this product and only after having carefully read the safety information applicable to this

product.

The safety information is provided in the Safety Information section in the “Legal, Safety

and Environmental Information” part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur ProduktsicherheitVon diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder

andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch

geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-

anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal,

Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-

satzes.

7/28/2019 Dn 70400137


DN70400137 3


Id:0900d805805a3251

Confidential

Table of contentsThis document has 17 pages.

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1 Unpacking IPA2800 Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.1 Dimensions and weights of the containers . . . . . . . . . . . . . . . . . . . . . . . 8

1.2 Before starting to unpack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.3 Unpacking the equipment cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.4 Lifting and moving the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.5 Conversion factors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7/28/2019 Dn 70400137


7/28/2019 Dn 70400137


DN70400137 5


Id:0900d805805a3251

Confidential

List of tablesTable 1 Conversion factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7/28/2019 Dn 70400137


6 DN70400137


Id:0900d805805a3251

Confidential

7/28/2019 Dn 70400137


DN70400137 7

Unpacking IPA2800 Cabinets Summary of changes

Id:0900d805804c82e4

Confidential

Summary of changesChanges between document issues are cumulative. Therefore, the latest document

issue contains all changes made to previous issues.

Changes in issue 3-0

The old delivery model, where equipment cabinets and plug-in units are delivered in

separate containers, is now optional, and is again included in this document.

Changes in issue 2-0

The delivery model was changed. Equipment cabinets are now delivered with plug-in

units installed. Because of this, plywood supports have been added, and the unpacking

process has been modified.

Equipment cabinets and cabling cabinets are delivered separately, so the information

on equipment and cabling cabinets delivered in the same container has been removed

from this document.

Changes in issue 1-0 (DN70400137)

Instructions on lifting and moving cabinets were clarified. The cabinets are heavy. Addi-

tional personnel or lifting equipment may be needed when moving, unpacking or lining

up the cabinets. Cabinets must not be lifted from the subrack edges. It is also not per-

mitted to step on or push the subrack edges down, because they will bend.

Document structure has been reorganised.

The DN number identification for this document has changed from DN0186515 to

DN70400137, and therefore issue numbering starts over from issue 1-0.


The dimensions and weights of the packages for the new cabinets EC216 and EC213

have been added, and the figures have been updated to correspond with the new cab-

inets' packages.


Dimensions and weights of the packages for deliveries containing cabling cabinets have

been added.


Corrections in graphics; no content update.


The first issue

7/28/2019 Dn 70400137


8 DN70400137


Id:0900d805805a31d3

Confidential


1 Unpacking IPA2800 Cabinets

1.1 Dimensions and weights of the containersThe IPA2800 cabinets are delivered in cardboard containers on a wooden pallet. There

are two types of containers: one suitable for an equipment cabinet (EC216), and one

suitable for a cabling cabinet (EC213).

Equipment cabinets

Equipment cabinets are delivered either pre-equipped with plug-in units and intracabinet

cables already installed or, optionally, without pre-equipped plug-in units. If the equip-

ment cabinet is not pre-equipped, the plug-in units are delivered in a separate container

and installed on the site.

Optional side plates and accessory materials are packed in the same container with the

equipment cabinet. The weight of the container depends on whether the cabinet is pre-equipped or not, and on the plug-in units, cables, side plates and accessory materials

included in the delivery.

Cabling cabinets

If you have ordered optional cabling cabinets, they are delivered in separate containers.

Container types and dimensions

Up to four containers can be piled on top of each other. The maximum height of a

delivery is 400 cm.

1.2 Before starting to unpack

Before starting to unpack the cabinets from their transportation containers:

• Make sure that the unpacking area is empty.

• Fetch the tools needed for unpacking (knife or side cutters, and a TX25 key).

1.3 Unpacking the equipment cabinet

Removing the cardboard container

• Remove the packing list attached to the case.

Container type Dimensions (H x W x L) Weight

EC216 (pre-equipped) 100.5 x 81 x 237 cm 330-430 kg

EC216 (without plug-in

units)

100.5 x 81 x 237 cm 280-310 kg

EC213 55 x 81 x 237 cm approx. 90 kg

7/28/2019 Dn 70400137


7/28/2019 Dn 70400137


10 DN70400137


Id:0900d805805a31d3

Confidential


Removing the cardboard collar

Figure 4 Remove the cardboard collar surrounding the cabinet.

1.4 Lifting and moving the cabinet

The cabinets are heavy. Additional personnel or lifting equipment may be needed when

moving, unpacking or lining up the cabinets. At least three people are needed when a

pre-equipped cabinet is lifted up without lifting equipment. Follow any applicable local

regulations when lifting and moving the cabinet.

Lifting the cabinet

Figure 5 Open the bottom end of the cardboard base and remove the cushion from

under the cabinet.

7/28/2019 Dn 70400137


DN70400137 11

Unpacking IPA2800 Cabinets Unpacking IPA2800 Cabinets

Id:0900d805805a31d3

Confidential

Figure 6 Move the cabinet so that its bottom end is outside the pallet.

Figure 7 Before lifting the cabinet, make sure the plywood support protecting the

cabling side of the cabinet is placed on the edge of the pallet. Carefully lift

the cabinet up.

Figure 8 Lift the cabinet to an upright position.

7/28/2019 Dn 70400137


12 DN70400137


Id:0900d805805a31d3

Confidential


Lifting the cabinet using lifting eyes

f

Lifting eyes are intended to be used during unpacking. Excessive lateral stress on the

lifting eyes may cause them to break. Make sure that the lifting belts are properly

attached. Stand clear of the cabinet while it is being lifted.

Figure 9 Four lifting eyes are included in the delivery. When using the lifting eyes,

lifting belts must be correctly attached through all four lifting eyes. The

angle between the belt and the top of the cabinet must be at least 60degrees.

Carrying the cabinet in a horizontal position

To install the lifting eyes, remove two cabinet feet from the corners on the cabling side

of the cabinet, and replace them with two lifting eyes. Also attach two lifting eyes to the

opposite end of the cabinet. Attach the lifting belts through two lifting eyes.

Min. 60o

DN70542175

7/28/2019 Dn 70400137


DN70400137 13


Id:0900d805805a31d3

Confidential

Figure 10 Install the four lifting eyes included in the delivery. Attach both lifting belts

through two lifting eyes.

DN70554303

7/28/2019 Dn 70400137


14 DN70400137


Id:0900d805805a31d3

Confidential


Removing the cardboard cover

Figure 11 Remove the cardboard cover from the cabling side of the cabinet.

Removing the plywood transport supports

Figure 12 Remove the plywood supports with a TX25 key.

Moving the cabinet

Cabinet doors must be kept closed when lifting and moving the cabinet. Do not lift or

move the cabinet from the subracks.

7/28/2019 Dn 70400137


DN70400137 15


Id:0900d805805a31d3

Confidential

Use rollers to move the cabinet. The rollers are included in the equipment kit, which is

delivered with the cabinet.

Figure 13 Place the rollers under the cabinet, next to the cabinet feet. Tilt the cabinet

slightly, if necessary.

Figure 14 When the cabinet is in its place, rotate the cabinet feet until they reach the

floor. Move the rollers away, slightly tilting the cabinet if necessary.

7/28/2019 Dn 70400137


16 DN70400137


Id:0900d805805a31d3

Confidential


7/28/2019 Dn 70400137


DN70400137 17


Id:0900d805805a31d3

Figure 15 Lifting the cabinet from the subracks, or stepping on or forcefully pushing

the subrack edges will bend and damage them.

Installing side cover plates

Figure 16 When opening the box that contains the side plates of the cabinet, be

careful if using a sharp tool, as it may damage the surface of the side

plates. Attach the side cover plates to the cabinet.

1.5 Conversion factors

The following conversion factors should be used when installing IPA2800 and associ-

ated equipment:

g For the purposes of installation and construction, an allowance of 1/16th of an inch is

tolerated between the physical conditions found on any particular site and the Blueprint

drawings provided with the installation instructions. In addition, an allowance of 1/16th

of an inch will be permitted when converting directly from European measurement to the American standard feet and inches.

Metric American

1 kilogram (kg) = 2.2046 lb

1 meter (m) = 3.2808 ft

2.54 centimeters (cm) = 1 in

Table 1 Conversion factors

dn 70400137

Documents