dns of surface textures to control the growth of turbulent spots
DESCRIPTION
DNS of Surface Textures to Control the Growth of Turbulent Spots. James Strand and David Goldstein The University of Texas at Austin Department of Aerospace Engineering. Sponsored by AFOSR through grant FA 9550-08-1-0453. Objectives. There are two primary objectives for the current work: - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/1.jpg)
DNS of Surface Textures to Control the Growth of Turbulent Spots
James Strand and David Goldstein
The University of Texas at AustinDepartment of Aerospace Engineering
Sponsored by AFOSR through grant FA 9550-08-1-0453
![Page 2: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/2.jpg)
Objectives
There are two primary objectives for the current work:
• Examine the structure and properties of large, mature spots at higher values of Rex than in our past work.• Determine whether surface textures continue to be effective at reducing spanwise spreading even as spots are followed significantly further downstream from the initial perturbation.
The University of Texas at Austin – Computational Fluid Physics Laboratory
![Page 3: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/3.jpg)
Introduction: Turbulent Spots
The University of Texas at Austin – Computational Fluid Physics Laboratory
• Boundary layer transition frequently occurs through growth and spreading of turbulent spots. These spots take on an arrowhead shape pointing downstream.1,2
• Spot grows in streamwise, spanwise, and wall-normal directions.
Spreading Angle
TrailingEdge
Initial PerturbationApex Angle
FrontTip
StreamwiseDirection (x)
SpanwiseDirection (z)
1 Henningson, D., Spalart, P. & Kim, J., 1987 ``Numerical simulations of turbulent spots in plane Poiseuille and boundary layer flow.” Phys. Fluids 30 (10) October.2 I. Wygnanski, J. H. Haritonidis, and R. E. Kaplan, J. Fluid Mech. 92, 505 (1979)
![Page 4: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/4.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Turbulent Spots – Flow Visualization
Visualization of a turbulent spot using smoke in air at different Reynolds numbers.3
3 R. E. Falco from An Album of Fluid Motion, by Milton Van Dyke
ReX = 100,000 ReX = 200,000
ReX = 400,000
![Page 5: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/5.jpg)
Introduction: Delaying Transition
• Drag reduction is a primary means for achieving gains in aircraft fuel efficiency.• Viscous drag is significantly greater for a turbulent boundary layer than for a smooth, laminar boundary layer. • If spanwise spreading of turbulent spots could be constrained, transition might be delayed until further downstream, resulting in lower viscous drag.
The University of Texas at Austin – Computational Fluid Physics Laboratory
![Page 6: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/6.jpg)
Numerical Method
• Spectral-DNS method initially developed by Kim et al.4
for turbulent channel flow.• Incompressible flow, periodic domain and grid clustering in the direction normal to the wall.• Surface textures defined with an immersed boundary method.
• Buffer zone is used to generate the inlet Blasius profile.
• Suction wall forces vertical velocity from Blasius solution to
allow for correct boundary layer growth downstream.
• Initial perturbation which triggers the spot is a small solid
body which appears briefly and then is removed.
4J. Kim, P. Moin, and R. Moser, “Turbulence Statistics in Fully Developed Channel Flow at Low Reynolds Number,” J. Fluid Mechanics, Vol. 177, 1987, pp. 133-166.
The University of Texas at Austin – Computational Fluid Physics Laboratory
![Page 7: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/7.jpg)
Introduction: Surface Textures
The University of Texas at Austin – Computational Fluid Physics Laboratory
5 Bruse, M., Bechert, D. W., van der Hoeven, J. G. Th., Hage, W. and Hoppe, G., “Experiments with Conventional and with Novel Adjustable Drag-Reducting Surfaces”,from Near-Wall Turbulent Flows, Elsevier Science Publishers B. V., 1993
• Correctly sized riblets reduce turbulent viscous drag ~5-10%.5 • Our past work has shown that surface textures can decrease the spanwise spreading of turbulent spots.
• If surface textures can constrain spanwise spreading of spots, turbulent
transition might be delayed, leading to significant drag reduction.
• Two textures examined:
• Triangular riblets
• Streamwise fins
• The textures are solid, no-slip surfaces. They force all three components of
velocity to zero, with the same immersed boundary technique used to create
the flat plate.
• Relevant parameters for both textures are height, h, and spacing, s.
h
s
h
s
![Page 8: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/8.jpg)
Simulation Domain – Comparison to Past Work
The University of Texas at Austin – Computational Fluid Physics Laboratory
• 768×192×768 spectral modes in the streamwise (x), wall-normal (y), and
spanwise (z) directions, respectively, for a total of 113,246,208 grid points.
• Each of these simulations required 36 days to run on 16 processors (13,824
processor hours or ~1.5 processor years).
• Our past work used 16,777,216 grid points (so current domain uses more
than six times as many).
• The domain is 50% longer in each direction than in past work, so total
volume of current domain is more than three times greater.
• We are able to follow the fully developed spot for twice as long as before.
• Rex ≈ 48000 and Reδ* ≈ 377 at the location of the perturbation.
• Rex ≈ 298000 and Reδ* ≈ 939 at the end of the domain.
![Page 9: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/9.jpg)
Simulation Domain
The University of Texas at Austin – Computational Fluid Physics Laboratory
• Total of 144 textures (riblets or fins) in each case.
• Crest-to-crest spacing for both texture types is 1.1 δo*.
• Riblet height = 1.1 δo* and fin height = 0.8 δo
*.
• Textures start flush with the plate and ramp up to full height over a short distance.
![Page 10: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/10.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Results – Flat Wall Spot
Isosurfaces of |ωx| showing spot growth. The arrowhead shape becomes more pronounced as the spot matures.
Isosurfaces of λ2 for the spot at time t3 above. Note the overhang region at the front of the spot.
![Page 11: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/11.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Results – Hairpins
Isosurfaces of λ2 help pick out the coherent vortical structures.
In this young spot, the hairpins all appear to be of roughly the same size.
Viewer is 40° above the horizontal looking down toward the spot and facing downstream.
![Page 12: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/12.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Results – Hairpins
Same view as previous slide, now showing a more mature spot.
There now appears to be a range of hairpin sizes present in the spot.
![Page 13: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/13.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Results – Hairpins
Same view as previous slide, now showing a large, well-developed spot.
A wide variety of hairpin sizes are present in the spot.
![Page 14: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/14.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Results – Comparison to Flow VisualizatoinVisualization of a turbulent spot using smoke in air at Rex ≈ 200000.
Flat wall spot at Rex ≈ 200000, shown with isosurfaces of λ2.
![Page 15: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/15.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Results – Textures vs. Flat Wall
![Page 16: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/16.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Results – Textures vs. Flat Wall
Flat Wall Riblets
Fins
Spots over the flat wall, riblets, and fins, shown at the same time step with isosurfaces of λ2. The riblet and fin spots seem to be elongated compared to the flat wall spot.
![Page 17: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/17.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Defining the Spot
Mature spot shown with two isosurfaces of |ωx|. Translucent blue isosurface is at a lower value (1/4 of the value for the red isosurface). Note that the leading and trailing edge locations are dramatically different depending on which isosurface is used to define them.
![Page 18: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/18.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Defining the Spot – Leading and Trailing Edges
X-normal plane of integration
An integral of |ωx| is calculated for an X-normal plane at each streamwise location.
![Page 19: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/19.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Defining the Spot – Leading and Trailing Edges
![Page 20: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/20.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Defining the Spot – Leading and Trailing Edges
![Page 21: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/21.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Defining the Spot – Leading and Trailing Edges
![Page 22: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/22.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Defining the Spot – Leading and Trailing Edges
Leading EdgeTrailing Edge
![Page 23: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/23.jpg)
The University of Texas at Austin – Computational Fluid Physics Laboratory
Wingtip Speed
y = 0.0476x + 9.4429R² = 0.9955
0
100
200
300
400
500
600
3600 4800 6000 7200 8400 9600 10800
Stre
amw
ise
Loca
tion
of S
pot W
ingti
p (u
nits
of
δ o* )
Time Step
• The streamwise location of the wingtip is calculated using three cutoff values of |
ωx| for each side of the spot. The wingtip position is then averaged across the
centerline to give one value at each time step. These values are plotted against time
and a trendline is fit to the data to determine wingtip speed.
![Page 24: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/24.jpg)
Wingtip, Trailing, and Leading Edge Speeds
The University of Texas at Austin – Computational Fluid Physics Laboratory
Texture Type Trailing Edge Speed
(units of U∞) Wingtip Speed
(units of U∞) Leading Edge Speed
(units of U∞)
Flat Wall 0.56 0.60 0.77
Riblets 0.60 0.62 0.79
Fins 0.58 0.60 0.81
• Wingtip speeds are very close to trailing edge speeds.
• Speeds for the texture cases are very similar to speeds for the flat wall case.
• Flat wall trailing edge speed is greater than commonly quoted value of 0.5 U∞,
and flat wall leading edge speed is less than commonly quoted value of 0.9 U∞.
This is unsurprising since we have defined the leading and trailing edges in a
different way than in most previous work.
![Page 25: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/25.jpg)
Spanwise Extent of the left side of the spot based on the blue isosurface.
Spanwise Extent of the right side of the spot based on the red isosurface.
The University of Texas at Austin – Computational Fluid Physics Laboratory
Spot Half-Width and Wingtip Location
• Three cutoff values of |ωx| are used to get an average edge location for each side of
the spot.
• Spot half-width is averaged across the spanwise centerline.
• Final spot half-width at any given time is an average of 6 total values.
![Page 26: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/26.jpg)
Spreading Angle
The University of Texas at Austin – Computational Fluid Physics Laboratory
• Even once spot is defined, questions remain. Should a virtual origin be used
when calculating the spreading angle?
![Page 27: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/27.jpg)
Virtual Origin
The University of Texas at Austin – Computational Fluid Physics Laboratory
Early Spot Developed Spot
![Page 28: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/28.jpg)
Average Spreading Rate
The University of Texas at Austin – Computational Fluid Physics Laboratory
• Plot of spot half-width vs. streamwise locations has many discontinuities.
![Page 29: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/29.jpg)
Average Spreading Rate
The University of Texas at Austin – Computational Fluid Physics Laboratory
• We use the average spreading rate as an additional, alternative measure.
• Average spreading rate is proportional to spreading angle as long as spot
wingtip moves downstream at a constant speed.
t1 t2
ΔHW
𝐴𝑣𝑒𝑟𝑎𝑔𝑒 𝑆𝑝𝑟𝑒𝑎𝑑𝑖𝑛𝑔 𝑅𝑎𝑡𝑒= ∆𝐻𝑊𝑡2 − 𝑡1
![Page 30: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/30.jpg)
Spreading
The University of Texas at Austin – Computational Fluid Physics Laboratory
Texture Type
Average Spreading Rate (units of U∞)
% Change Compared to Flat Wall
Flat Wall 0.0812 -
Riblets 0.0753 -7.3
Fins 0.0750 -7.7
Texture Type
Spreading Angle (°) % Change Compared
to Flat Wall
Flat Wall 7.6 -
Riblets 7.1 -6.0
Fins 6.9 -8.8
• Textures decrease spot spreading by ~7-8% with by either measure.
![Page 31: DNS of Surface Textures to Control the Growth of Turbulent Spots](https://reader036.vdocuments.net/reader036/viewer/2022070320/56814656550346895db36f74/html5/thumbnails/31.jpg)
Conclusions and Future Work
Conclusions:• Turbulent spots contain a multitude of hairpin vortical structures, entangled with one another throughout the spot.• More mature spots have a broader range of hairpin sizes.• Spot wingtips move at a constant speed, and thus average spreading rate is a reasonable alternative to the spreading angle as a measure of texture effectiveness.• Surface textures are able to reduce the spreading of large, mature spots. Textures examined here reduced spreading by ~7-8% compared to the flat wall value.
Future Work:• Even larger domains might be used to follow spots even further downstream.• Ensemble averaging should be used to further solidify the results of this work.• Turned riblets, as described by Chu et al.6 show promise for achieving greater reductions in spot spreading. They will need to be tested for larger domains at higher Reynolds numbers.
The University of Texas at Austin – Computational Fluid Physics Laboratory
6J. Chu, J. Strand, and D. Goldstein, “Investigation of Turbulent Spot Spreading Mechanism,” AIAA-2010-0716, 48th AIAA Aerospace Sciences Meeting, 4-7 January 2010, Orlando, Florida.