doc. no. jn87-01066 c02mts.p-two.com.tw/資料中心/erp承認書/87-lvds/jn87... · 2015. 3....

DOC. NO.：

ISSUE DATE：

CUSTOMER：

PART NAME：

PART NO.：

APP. DATE：

■ P-TWO INDUSTRIES INC. NO. 9, SHIN HWA RD, KWEI SHAN IND. PARK TAOYUAN, 330 TAIWAN, R.O.C. TEL:00886-3-3766666 FAX:00886-3-3762222

□ P-TWO ELECTRONIC(S.Z.) LTD. NO.1,GONG YE NORTH ROAD,CO-PROSPERITY, INDUSTRIAL PARK, SONGGANG TOWN, BAOAN DISTRICT, SHENZHEN CITY, GUANGDONG, CHINA TEL:86-755-27551666 FAX:86-755-27551222

□ P-TWO ELECTRONIC TECHNOLOGY(SUZHOU) CO.,LTD. NO.158-86 HUASHAN RD.FENG QIAO INDUSTRIAL PARK OF SUZHOU NEW DISTRICT,JIANGSU,CHINA TEL:86-512-6617666 FAX:86-512-6617222

MANUFACTURER SIGNATURE

JN87-01066-C02

2015/03/16

LVDS 7 A TYPE

187066-30091

Rev Date Page Reason for revision ISS.

C01 2009.01.23 Initial Release Kun .Tsai

02 2015.03.16 6 of 15 Add Recommend Cable Thickness Kun .Tsai

HISTORY REVISION

Part No: 187066-30091

This document contains information that is proprietary to P-TWO INC., and should not be used without permission.

Issue Date:2015/03/16

Page:1 of 15

Part Name: LVDS 7 A TYPE

Doc. No.:JN87-01066

REV.:01

P-TWO INDUSTRIES INC.

I. SPECIFICATION OF PRODUCT

II. ORDERING INFORMATION

III. INFRARED REFLOW REFERENCE CONDITION

IV. PRECAUTION FOR USE

V. CONTACT MATERIAL CERTIFICATE OF TERMINAL

VI. CONTACT MATERIAL CERTIFICATE OF SHELL

VII. CONTACT MATERIAL CERTIFICATE OF GROUND

VIII. PLASTIC MATERIAL CERTIFICATE OF HOUSING

IX. MATERIAL REFERENCE TABLE

X. THE CONFIRMATION OF PROHIBITED/CONTROLLED

SUBSTANCES

XI. ENGINEERING DRAWING OF PRODUCTS

INCLUDE PRODUCT & PACKAGE

TABLE OF CONTENT

Part No: 187066-30091



Page:2 of 15


Doc. No.:JN87-01066

REV.:01


1. Scope This product specification contains the test method , the general performance and requirement for interconnection system connectors. The specification covers LVDS 1.0 PITCH series connectors manufactured by P-TWO INDUSTRIES INC.

2. .Applicable documents:

The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1 Military Standard and Specifications:

MIL-STD-1344 Test Methods for Electrical Component Parts. MIL-STD-202 Test Methods for Electronic and Electrical Component Parts

3.Requirements: Designs and Construction:

Product shall be of the design,construction and physical dimensions specified in the applicable product drawing. Materials:

A.Terminal：Copper Alloy C5210R-SH,t=0.15mm. Plating: Connecting Area is plated with Gold 5μ”Min. ,Overall Bright Tin(LEAD FREE)75μ”Min.

Nickel 50μ” Min. underplated B.Ground：Copper Alloy C5191R-H,t=0.15mm. Plating : Bright Tin

(LEAD FREE)100μ” Min., Overall Nickel 50μ” Min. underplated. C.Shell：Stainless Steel , SUS304R-3/4H ,Solder Area plated with Gold

4μ”Min. ,Overall Nickel 10μ”Min. underplated. D.Housing：High Thermoplastic, LCP MG-350 (UL94 V-0)

4. Characteristics Voltage rating： 200V DC Current rating： 1 Amps/Contact Storage temperature range： -40°C to +80°C

5. GP requires substances (level1) forbidden (including orders placed to subcontractors)

SPECIFICATION OF PRODUCT

Part No: 187066-30091



Page:3 of 15


Doc. No.:JN87-01066

REV.:01


6. Mechanical Performance

Item Description Test method ＆ Condition Requirement

6-1 Durability 50 cycle of inserting and separating action are conducted and measure contact.

Low level contact resistance:

80mΩ Max.

6-2 Mating force Insertion is conducted between applicable connectors.（without locking lever）

1.96N X n Max. “n”=number of pins

6-3 Unmating force Separation is conducted between applicable connectors.（without locking lever）

0.25N X n Min. “n”=number of pins

6-4 Vibration

In accordance with method 201 of MIL-STD-202, all contacts shall be connected in series and DC 100mA shall be applied. Wave form: Sine wave. Frequency: 10-55-10 HZ Amplitude: 1.5mm Orientation: X,Y,Z (3 axes). Duration: 2hrs/axis

6-5 Shock

In accordance with method 202 of MIL-STD-202. DC 100mA shall be applied. MAX acceleration:50G Wave form: Half sine wave. Orientation: X,Y,Z(3 axes). Duration: 11ms/axis. Times: 3 time/axis

No electrical discontinuity more than 1 μs. No damage.


Part No: 187066-30091



Page:4 of 15


Doc. No.:JN87-01066

REV.:01


7. Electrical performance


7-1 Dielectric withstan-

-ding voltage

The connector shall be tested in accordance with method 3001of MIL-STD-1344A. When the 500V AC r.m.s for one minute applied between adjacent contacts.

There shall be no current leakage and flashover or damage detected.

7-2 Insulation resistance

It should be tested in accordance with method 3003 of MIL-STD-1344A. When 100V DC is applied between adjacent contacts and insulation resistance is measured within one minute.

100MΩ Min.

7-3 Contact

resistance

It should be tested in accordance with method 3004of MIL-SDT-1344A. Measure by low level （Max：20mV，

100mA） 40mΩ Max.

8.Environmental performance


8-1 Humidity (steady state)

Subject mated connectors to steady state humidity at 60℃ and 90~95% R.H. to 96 hours. Method103 of MIL-STD-202.

8-2 Thermal shock

Subject specimens to continuous 5 cycles between -55°C and +85°C for 30minutes each.

Insulation resistance:50MΩ

(Min.) Voltage proof: 250V r.m.s. 1minute No breakdown. Contact resistance:80mΩ

(Max.)


Part No: 187066-30091



Page:5 of 15


Doc. No.:JN87-01066

REV.:01


8-3 Salt spray

Connector shall be tested in accordance with method 1001 of MIL-STD-202. Temperature：35±2 ℃

Density：5% in weight Duration：48 hours

resistance: Max. 80mΩ.

8-4 Solderability

The end of post shall be dipped in accordance with method 208 of MIL-STD-202. SolderingTemperature: 245±5°C Soldering time: 5±0.5 sec

More than 95% of the immersion shall be covered with solder

8-5 Soldering Heat Withstanding

It should be tested to compare with method 210 of MIL-STD-202. Soldering temperature: 260±5°C Duration time:5±0.5 sec. Consecutive 2 cycles

No physical damage


Part No: 187066-30091



Page:6 of 15


Doc. No.:JN87-01066

REV.:01


LVDS 1.0 mm PITCH CONNECTOR SMT TYPE

Specifications:

Part Name: LVDS (FEMALE) Connectors

Connector Styles: SMT Type

Mounting of Connector Sunk Into The Board

Centerline (Pitch): 1.00 mm (0.04 inch)

No. of Contacts: 30 PIN

Recommend Cable Thickness: Wire : 0.53~0.57mm ; FFC : 0.57~0.62mm

Part No:

187066– 30 09 1 (1) (2) (3)

(1) 30: PIN NO. (2) 09: PLATEING GOLD with BRIGHT TIN(100％) (3) 1: PACKAGED

CARRIER

ORDERING INFORMATION

Part No: 187066-30091



Page:7 of 15


Doc. No.:JN87-01066

REV.:01


(For Solderability)

INFRARED REFLOW REFERENCE CONDITION

50

150

100

200

50

250

100 200 150 250 300

T1 T2 T3 T4

RAMP UP TIME

Peak Temp.

Max. 260℃

5 SEC

RAMP UP

2℃~5℃/SEC

PREHEAT

150℃~200℃/SEC

100±20 SEC

OVRE 220℃ Min.

30~50 SEC

260℃ 5 SEC Max.

RAMP DOWN

T1 Temperature ramp up rate 2℃~5℃/SEC

T2 Preheat: 150℃~200℃ 100±30 SEC

T3 Time over 220℃ 30~50 SEC

T4 Ramp down rate during cooling 4℃~7℃/SEC

※ Consecutive 2 cycles

※ Peak temperature 260℃ Max.

(For Soldering Heat Withstanding)

Part No: 187066-30091



Page:8 of 15


Doc. No.:JN87-01066

REV.:01


About mating connectors 1. The connectors should be mated/unmated each other in parallel way.

2. Mating Do not insert a connector to a counterpart if there is a gap (A) shown above in other side as they are being mate. Confirm that the plug and the receptacle are guided to each other. The plug should be inserted with 5° (Max.) diagonally to the width direction.

PRECAUTION FOR USE

Part No: 187066-30091



Page:9 of 15


Doc. No.:JN87-01066

REV.:01


3. Unmating Pual out a cable side connector in parallel to a counterpart connector. Do not hold and turn neither sides of the base nor the cable to unmate the Connectors as shown in the figure.

4. Do not bend the pc board in directions shown in the figure.

PRECAUTION FOR USE

Part No: 187066-30091



Page:10 of 15


Doc. No.:JN87-01066

REV.:01


CONTACT MATERIAL CERTIFICATE OF TERMINAL

Part No: 187066-30091



Page:11 of 15


Doc. No.:JN87-01066

REV.:01


CONTACT MATERIAL CERTIFICATE OF SHELL

Part No: 187066-30091



Page:12 of 15


Doc. No.:JN87-01066

REV.:01


CONTACT MATERIAL CERTIFICATE OF GROUND

Part No: 187066-30091



Page:13 of 15


Doc. No.:JN87-01066

REV.:01


PLASTIC MATERIAL CERTIFICATE OF HOUSING

Part No: 187066-30091



Page:14 of 15


Doc. No.:JN87-01066

REV.:01


PLASTIC MATERIAL CERTIFICATE OF UL YELLOW CARD

Part No: 187066-30091



Page:15 of 15


Doc. No.:JN87-01066

REV.:01


Parts Name General Name Model No. Heat Resistant

Level UL Card No. Specific Weight

Terminal

Copper Alloy

C5210R-SH

0.082g/16.08%

Housing

LCP

MG-350

UL94 V-0

E91944

0.097g/19.02%

Shell

Stainless Steel

SUS304R-3/4H

0.275g/53.92%

Ground

Copper Alloy

C5191R-H

0.056g/10.98%

Total weight: 0.51g

MATERIAL REFERENCE TABLE


Satisfying customer & obeying the law and regulations.

Protecting pollution, reducing waste & saving energy.

All the staff join in & improve frequently.

Taking person as foundation & keep safety .

QUALITY/ENVIRONMENTAL SAFETY POLICIES

doc. no. jn87-01066 c02mts.p-two.com.tw/資料中心/erp承認書/87-lvds/jn87... · 2015. 3....

Documents