Transcript
Page 1: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

1

HOMEOWNER’S GUIDE TO DESIGNING AN HVAC SYSTEM

9 Steps to building the

Ultimate HVAC system.

THE ULTIMATE

How to get everything you want and

need in the budget you can afford!

Don Johnson

Page 2: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

2

Copyright © 2012 by Don Johnson. All rights reserved.

Limit of Liability/Disclaimer of Warranty: While the author has used his best efforts in preparing this book, he makes no representations or warranties with respect to the accuracy or completeness of the contents of this book and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. No warranty may be created or extended by sales representatives or written sales materials. The advice and strategies contained herein may not be suitable for your situation. You should consult with a professional where appropriate. The author shall not be liable for any loss of profit or any other commercial damages, including but not limited to special, incidental, consequential, or other damages. For general information about our products or services, please visit our website at

www.FreedomHvacAL.com

2

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 3: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

3

Chapter 1. Design 7

The Importance of Proper Design of a Heating and Cooling System

Chapter 2. Size 8

Why Heat Load Calculations Will Make You Question Everything You Have Heard

From Your HVAC Guy

Chapter 3. Basic equipment style 9

Heating and Air Conditioning Once Saved the World: Part 1

Heating and Air Conditioning Once Saved the World: Part 2

Which is the Best Air Conditioner Brand?

Package Unit vs. Split System

Air Conditioner vs. Heat Pump

How a Variable Speed Fan is Making the World a Better Place

Chapter 4. Return air and Duct Design 20

HVAC Performance Depends on Good Ductwork

The Problem with Leaky Ducts

Do I Need a Duct Cleaning?

Chapter 5. Equipment feature and selection 23

An Expert Interview About SEER

What is a Ton of Air Conditioning?

Single Stage vs. Two Stage Compressors

Furnace Heat Chambers: Aluminized Steel vs. Stainless Steel Why is New Copper for Refrigerant Lines Important?

Chapter 6. Enhancements and controls 27

Do I Need a New Digital Thermostat?

I Have Elderly Parents Who Have A Difficult to Operate Thermostat.

Can You Recommend An Easy to Use Solution?

Will a Nest Thermostat Work with my AC System?

Does It Matter How You Achieve Efficiency? Or that you get a lower power bill!

How Much Insulation Do I Need in My Home?

Table of Contents

3

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 4: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

4

Spray Foam Insulated Attics

My evaporator coil is leaking, why? or Why do I have a leaking evaporator coil?

How to Prevent Evaporator Coil Leaks?

Chapter 7. Allergy protection 33

Several Insane (but true) Things About Humidity

MERV, Not Another Funny Texting Letters

How Can I Know If I Have Mold and Mildew in My Ventilation System?

Air Duct Cleaning Service or a Better Air Filter, Which is the Best Investment?

Clean Indoor Air; A Simple Guide to Indoor Air Quality

5 Ways To Deal With Crawl Space Air

Chapter 8. Warranty and price 41 Why No One Talks About Their Home Warranty Anymore The insiders secrets to All the credits and rebates available in Birmingham, AL Costco members earn CASH from HVAC Installation How Much Does an Air Conditioner Cost? What's the Price of a Heating and Cooling System? Can I Get A Lower Price? Can I Just “3 Bids” in the HVAC Industry!

Chapter 9. Maintenance after installation 51

Heating Season Tune-ups Save Money, And Maybe Your Life

What is the Freedom Comfort Club?

Bonus: Water Heater and Home Enhancements 53

Tankless vs Tank Water Heater

Electric Water Heater vs Gas Water Heater

How Hot to Set Your Water Heater?

Whole House Generators Can Keep You Out of Trouble

Ductless AC in Every Home Means Comfort and Savings

Protect Yourself and Your Electronics From Lightning Strikes

Conclusion 59

4

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 5: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

5

Quick Background

As you may know, I am the president and owner of Freedom Heating and Cooling in Birmingham,

Alabama.

Why This eBook is Different

I wanted to put together a collection of information that gives all the years of experience and

learning into a comprehensive guide. This is not a sales book or letter. It is just the information

and process we use every day.

How to Read this Book

This book consists of blog post I have written. They are organized by chapter and topic and flow

in an order of how we approach every project. Not all items will fit your situation and not all items

will be relevant.

We are here to help

We have a staff of dedicated and educated people that can help with any aspect of your HVAC

project. Good luck to you in this process and may the teachings of this book help you and your

family experience great comfort, energy savings and allergy protection for years to come.

Are You Going to Try to Sell Me Something I Don't Need?

Is that question running through your mind? It's because an unethical salesman came to your home and pressured you to buy either steak knives or a vacuum cleaner. He would not leave until your bought something. We are not high pressure salesmen. We believe that you have control over your home's HVAC system decisions.

Our responsibility is to inform you of your choices and educate you. We typically will present from three to five choices for any repair, enhancement or replacement you may need.

Who Has the Power in Sales?

Most people dread when faced with the situation that they must replace their AC system. They start asking for bids, estimates and quotes. I think the name Upgrade Choice Presentation is what most people really want.

Who has the power to make decisions in a sales call? Of course the customer does. The simplest way to show respect to the customer is to present appropriate choices and allow them to make a decision. High-pressure sales tactics use a lot of yes or no questions and try to "box" the customer into the sale. Ethical sales, in any industry, is about giving the customer appropriate choices that are relevant to his needs and wants. The choice to upgrade, the choice to repair, or the choice of an ultimate package is the customer's decision.

High-pressure sales tactics use a lot of yes or no questions and try to "box" the customer into the sale. Ethical sales, in any industry, is about giving the customer appropriate choices that are relevant to his needs and wants. The choice to upgrade, the choice to repair, or the choice of an ultimate package is the customer's decision.

5

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Introduction: What this ebook can do for YOU...

Page 6: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

6

6

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

The Pope just said "who am I to judge". If he does not have the authority to make decisions for the Catholic world, then how can a salesman have the right to pressure customers? The customer is in control when it comes to their pocket book. Think about this personally; if a person enters your home to sell something, they should present at least 3 choices to you or they not respecting your right to make a choice.

What do you think? Who do you want in your home, a high pressure closer or an ethical choice provider?

Before making any decisions about your HVAC system consider all of the following areas to

building the ultimate heating and cooling ducted system. All these items may not be needed for

every person but having a choice is what empowers your decision making

HVAC: What Does it Stand For?

HVAC is seen in the air conditioning industry for both residential and commercial contractors. It

stands for Heating, Ventilation and Air Conditioning.

Heating: This is all forms of heating such as furnaces and heat pumps. Ventilation: This means more than it seems. It is the duct work, the filters, the air purifiers and the exhaust fans in kitchens and bathroom. It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out the internal area of your duct system.

Air Conditioning: This is the heart of the industry. Newer designed systems such as ductless air conditioning or ductless mini splits are also included in the HVAC industry.

This is a very simplified explanation but I think you get the point.

Page 7: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

7

7

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

CHAPTER 1: DESIGN

Many clients often ask us tell them what they need for their heating and cooling system. That is a very involved question. It can depend on your family, the property arrangement, and how a home owner will use a property. Getting a proper design of a heating and cooling system before you start buying and installing HVAC equipment will lead to a much better system and a happy homeowner.

We recently took over a job where the previous contractor didn't do any planning. He installed the equipment with the service panel against a wall. This will lead to many headaches in the future when a simple adjustment is needed. The unit would have to be removed, fixed and then reinstalled just for a simple change in the blower speed. Planning and design are a critical part of a successful and happy client. Many HVAC service technician just jump into work and may not be thinking the full project through. We came in to finish a job the previous contractor started but did not have the expertise to correct all the problems he created.

We use a simple survey form to get clients thinking about the full project and it even helps them realize that a comfort system can do more than provide warm or cool air. Heat, cool, comfort, efficiency, price, allergy control, are any of these important? A proper system can clean the air, purify the air of living organisms, control humidity, provide fresh air from outside the home. A comfort system can balance airflow to all rooms and can save on utility costs. But all of these items can seem over whelming. A design plan and survey keeps it all organized.

After completing a survey, the process is to prioritize the items in order of importance. This will greatly reduce the reengineering that sometimes occurs when work is started then it is planned.

Call us at 205-444-4444 when you are ready to plan your project!

The Importance of Proper Design of a Heating and Cooling System

Page 8: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

8

8

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

You may be asking "What is a Heat Load Calculation?" A heat load calculation , also called the manual j calculation, is the starting point for providing the proper size unit for a house. The calculation and factors are different for the different areas of the country. A home in Birmingham Alabama will need more AC and less heat than a home in Minneapolis, Minnesota. The manual j design takes areas into account and offers different factors and heating and cooling days into the calculation. In fact, in Alabama, homes are designed for 95 degree temperatures in the summer. Manual j Calculations make assumptions of 2 people per bedroom in a home, this is not always true. Kitchens produce heat, the calculations have an average kitchen load in it. If you cook a lot, have a double oven, or you are running a small bakery, this will greatly add to the heat load in a home.

Some technicians base the size of the AC on the square footage of the home. This is a large factor but not the only factor. Most people think, my neighbor down the street has the same home, isn't that the right size? But the orientation of a home is very critical. If the majority of windows, front and back, are facing east and west, you will receive more sun into your home and that will increase heat load and the cooling needed. Other important factors are windows type, exterior door type, and insulation.

You may be thinking, I've had a 3 ton for years and it has always done fine, why shouldn't I skip this step? We here this same comment all the time. A size unit is its nominal size. The nominal size is the ability cool the air in a home while the latent size is the ability to cool or control the temperature of the items inside a home. Latent heat is the hidden heat. It's the heat inside the furniture, carpet, drapes, etc inside the home. An air conditioner must cool the air but it must also cool the items inside the home as well. Many newer units with the same nominal size do not produce the same amount of latent cooling capacity.

Here is a copy of the form we use in Birmingham, Alabama. https://dl.dropboxusercontent.com/u/57912774/Consumer%20Guides/Client%20List%20-%20Heat%20Load%20Analysis.pdf

Why Heat Load Calculations Will Make You Question Everything You

Have Heard From Your HVAC Guy

CHAPTER 2: SIZE

Page 9: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

9

9

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

You may be beating summer's heat by reading this in a cool, comfortable place with your air conditioner running. Air conditioning is as familiar to our modern world as freeways, jet air travel and gourmet coffee. Yet most senior citizens grew up in a world in which air conditioning was a luxury rather than a part of everyday life. Most people could enjoy it only in commercial buildings and the wealthiest homes.

The invention of modern air conditioning traces back to 1902, when a Brooklyn, NY, printing firm found that distortion in the paper caused by excess heat and humidity made it hard to align color images. A clever young engineer named Willis Carrier designed a way to control temperature and humidity for the printing firm. In 1906, Carrier patented that initial device, called "An Apparatus for Treating Air."

In 1924, air conditioning expanded into a human comfort mode. The first comfort cooling system was installed at Detroit's popular J.L. Hudson Department Store, where many people fainted from the heat at the store's crowded bargain basement sales. The 1920s also saw movie theaters adopt air conditioning in a competitive race for customers. During the Great Depression of the 1930s, watching a movie in air conditioned comfort was one of the few affordable pleasures available to many Americans. Even into the 1950s, the front of many movie theaters had a familiar blue sign showing a block of ice and advertising, "It’s cool inside!"

The Great Depression and then World War II retarded the growth of air conditioning for the masses. Residential air conditioning didn't begin to take off until the 1950's building boom in suburban America. In 1955, about 430,000 homes in the United States had central air conditioning. Ten years later the number had grown to an astounding 3 million homes. By 1985, 70% of all new homes had central air conditioning - about 90% in the South. Today about 80% of U.S. homes have central air conditioning; those without it tend to be in relatively cool northern climates.

Many historians credit the growth of air conditioning as a key factor in the dramatic rise of the southern Sun Belt in population and economic growth during the post-World War II era. Before air conditioning became widespread, few businesses wanted to locate in the South, where stifling, sultry summers took a toll on workers and machinery alike. Air conditioning has turned the South's warm climate from a handicap into an asset.

And it has made summertime even more of a treat to residents of the North, who are less acclimated to high temperature and humidity than their southern counterparts. Air conditioning truly ranks as one of the most important inventions of modern times for the average citizen. It is a mark of success how much we have come to take it for granted.

Heating and Air Conditioning Once Saved the World: Part 1

BASIC EQUIPMENT STYLE

CHAPTER 3: BASIC EQUIPMENT STYLE

Page 10: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

10

10

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

There are so many names in the Heating and Air Conditioning Industry. This is simply a post (Heating, Air Conditioning Brands) to understand how the names are very connected with a brief history.

Carrier Owner or Parent Company: Willis Haviland Carrier is the owner and part of the UTC Climate, Controls & Security Parent Company

Address: P.O. 4808 Carrier Parkway Syracuse, N.Y. 06034-4015

Brand: Carrier, Tradiran, Bryant, International Comfort Products, Linde Refrigeration, Payne, Transicold, Heat Transfer Products Group, Arco aire, Comfortmaker, Heil, Tempstar and Totaline.

History: In 1920 while staring through mist Willis Carrier realized he could dry air passing it through water to create fog, and in doing so he could control the amount of moisture in it. Within a year he has invented a way to control humidity, and is now credited what is known for the modern air conditioner. In 1915 he along with six other engineers pooled together in to form the Carrier Engineering Corporation. They purchased their first plant in Newark, New Jersey in 1920. In 1950 he began marketing its air conditions to the residential market.

Manufactured: Carrier has access to 67 manufacturing facilities worldwide

Distributed: Willis Carrier developed a network of international dealers, distributors and customers worldwide.

Goodman

Owner or Parent Company: Daiken via Goodman Global Group Inc.

Address: 7401 Security Way Houston, TX 77040

Brand: Goodman, Amana and (Janitrol- no longer used)

History: In 1954 the founder of Goodman Manufacturing Company, L.P. Harold V. Goodman became an air conditioning contractor in Houston Texas. As the city grew, so did his business. He was one of the most successful HVAC contractors in the United States by the late 1960’s.

Harold entered HVAC manufacturing with Goodman Manufacturing Company, L.P. in 1975. They began machining flexible air duct and plastic blade registers. As his business was growing he decided to build HVAC equipment recognizing the need for high quality, low-cost central air conditioning

Heating and Air Conditioning Once Saved the World: Part 2

Page 11: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

11

11

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Heating and Air Conditioning Once Saved the World: Part 2 Cont.

systems. As another HVAC manufacturer closed he quickly stepped in and purchased the company’s machinery and entered the market as a manufacturer of central air conditioners and heat pumps in 1982.

Manufactured: Goodman Global engineers, manufactures, assembles, markets and distributes their line of products.

Distributed by: Goodman Global Group products are sold through a North American distribution network with nearly 1000 total distribution points including both company-operated and independent distributors.

Lennox Owner or Parent Company: David Windsor Norris of Lennox Furnace Company

Address: 2100 Lake Park Blvd. Richardson, TX 75080 P.O. Box 799900 Dallas, TX 75379-9900

Brands: Lennox, Armstrong, Ducane, and Aire-Flo

History: In 1895 Ernest Bryant and Ezra Smith from Iowa shared their plans with David Lennox for a furnace of riveted steal surface that heated homes. They were made entirely of cast iron which would crack and warp after extended use, and caused smoke and coal gasses to spread through homes. Because Lennox grew up worked with Iron in a Steel Company and owned his own blacksmith and machine shop, Bryant and Smith entered an agreement with him in which Lennox made the iron castings used for their steel furnaces. Bryant and Smith lost their financial backing so Lennox took over their patents and reworked their original design.

In 1904 Lennox sold his furnace business to a group of business men led by David Windsor Norris. Norris operated the company under the name of Lennox Furnace Company and was renamed Lennox Industries in the early 1950’s. Lenox Industries became Lennox International Inc. in 1984 and 95 years after being owned privately by the Norris family it was made public in 1999 and is currently traded on the New York Stock Exchange.

After the sale of his furnace business, Dave Lennox continued to manage the Lennox Machine Company in Marshalltown until he sold it in 1912, but continued to work in a small machine shop behind his home for the remainder of his retirement.

Manufactured: Richardson, TX;, Carrollton, TX; Des Moines, IA; Marshalltown, IA; Stuttgart, AR; and Orange, CA;

Distributed by: Lennox has over 6,000 dealers in North America

Page 12: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

12

Heating and Air Conditioning Once Saved the World: Part 2 Cont.

Nordyne Owner or Parent Company: CEO and President is Dave LaGrand

Address: 8000 Phoenix Parkway O’Fallon, MO 63368

Brands: Broan, Frigidaire, Gibson, Kelvinator, Light Commercial, Maytag, NuTone, Philco, Tappan, Westinghouse, Intertherm (no longer used), Mammoth and Miller

History: In 1919 Nordyne was founded as International Oil Heating Co in St. Louis and was later purchased by Sidney Heiman and Truman Brown in 1926.

International Oil Heating Company was one of the first companies to use radio for advertising and developed the first heater and air conditioners and became known for developing products for their use in trailers and mobile homes

Manufactured: Boonville, Missouri; Dyersburg, Tennessee; Poplar Bluff, Missouri, and Tipton, Missouri

Distributed by: Boonville, Missouri; Poplar Bluff, Missouri, Monterrey, and Nuevo Leon, Mexico

Rheem Owner or Parent Company:

Address: 1100 Abernathy Road Suite 1400 Atlanta, GA 30328

Brands: Rheem, Ruud and Weatherking

History: In 1927 Rheem was established by Richard and Donald Rheem when they acquired a galvanizing plant. Rheem began manufacturing water heaters in the 1930’s and by 1936 they had coast to coast distribution. In the 1940’s and 1950’s the company began producing space heating units for homes, oil furnaces and air conditioners. In 1959 Rheem acquired Rudd Manufacturing Company and then expanded with the rapid growth of the central air conditioning industry. In 1985, the company purchased Raypak, a leading producer of copper tube boilers. Today Rheem is a leading producer of water heaters, central warm air furnaces and air conditioners, swimming pool heaters and commercial boilers for both residential and commercial.

Manufactured: Mobile, Alabama; Fort Smith, Arkansas; Oxnard, California; and Eagan Minnesota.

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

12

Page 13: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

13

Heating and Air Conditioning Once Saved the World: Part 2 Cont.

Distributed by:

Distribution centers include Randleman, NC; and throughout the US and Bampton, Ontairo,

Canada. Rheem also has an international presence in Countires such as Australia, Canada,

Mexico, Brazil and Singapore.

Sears Owner or Parent Company: Sears is officially named Sears, Roebuck and Co and was founded by Richard Warren Sears and Alvah Curtis Roebuck in the late 19

th century. In 2005 Dow Jones Industrial Average, Kmart

bought out sears creating the Sears Holdings Corportation.

Address: Sears National Customer Relations 3333 Beverly Road Hoffman Estates, Illinois 60179

Brands: Whirlpool, Kenmore

History: In 1893 Sears, Roebuck and Co. was officially formed although it’s history date back to 1886 when Richard W. Sears of Minnesota sold gold watches to other agents. After Hercules steam heating systems began replacing iron stoves and fireplaces with central heating sources in 1908, Sears launched its Kenmore brand, but it wasn’t offered to consumers until 1977. However, Coldspot air conditioners were offered to the public in 1928.

Manufactured: Sears Manufacturing Co: Davenport, IA 52802

Distributed by:

Sears Distribution Center: Pearl city, HI 96782

Trane Owner or Parent Company: Ingersoll Rand and is the successor company to the American Standard Companies.

Address: Trane Residential Customer Relations P.O. Box 9010 Tyler, TX 75711-9010

Brands: American Standard, Trane

History: In 1885 the founder James Trane, a Norwegian immigrant opened a plumbing shop in La Crosse, WI. Inspired by the cold winters, he invented a Low-pressure heating system called Trane Vapor Heating System. In 1913 James and his son Reuben that had just received a degree in

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

13

Page 14: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

14

Heating and Air Conditioning Once Saved the World: Part 2 Cont.

mechanical engineering incorporated The Trane Company. The company’s reputation was firmly established in 1923 with Reuben’s invention of the convector radiator which replaced the cast iron radiators.

Trane became pioneer in 1931 when they used technology to relieve people from the summer heat by developing the first air conditioning unit.

In 1938 the launch of Turbovac, the centrifugal refrigeration machine was the beginning of innovations that lead to Trane’s Current CenTraVac the standard for large commercial air conditioning systems.

With the acquisition of Sentinel Electronics in the late 1970’s residential air conditioning began in 1982.

Manufactured: Trane has 104 manufacturing locations in 28 countries. Residential products are manufactured in Arkansas, Mexico, New Jersey, Texas and Georgia.

Distributed by: Top Distributors are: Dallas, Tx; Tacoma, Wash.; Phoenix, AZ; New Haven, Conn.

York Owner or Parent Company: Johnson Controls Inc.

Address: Johnson Controls Unitary Products Or York International Corp. 5005 York Drive P.O. Box 1592 Norman, OK 73069 York, PA 17405-1592

Brands: Frasier Johnston, Coleman, Luxaire, York

History: In 1874 York was founded in York PA where ice machines were being made as an alternative to shipping ice from the Great Lakes to the Company. They soon extended their refrigeration expertise to other areas such as Montgomery, Alabama. They installed the Empire Theatre with a comfort system called “air washing” which in time became air conditioning in 1914. The world’s first air conditioned office building in California was in 1924 where York equipment was used. The publicly traded company was purchased by Johnson Controls in 2005.

Manufactured: Norman, Oklahoma

Distributed by: Locally by M&A Supply Company

Thank you for reading this long post of Heating, Air Conditioning Brands.

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

14

Page 15: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

15

One of the most common questions asked is: "Which is the best air conditioner brand?"

While others have their personal favorites or would simply try to sell the most expensive units, my answer is probably one of the most honest: "depends on what you need it for and who you ask." For every brand out there, any technical product or service, there is a list of people who are willing to swear by it and probably a longer list of people who will curse it till the day they die.

Air conditioning systems are no different… It often comes down to customer service when dealing with issues since most companies are using the exact same air conditioner brand.

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Which is the Best Air Conditioner Brand?

15

Heating and air is not a purchased as a system like a car. Heating and air conditioning is an on site assembled system. If car manufacturers simply made all the parts, put them in a box, and ship them to the local dealer to install, the quality control of workmanship would not be available. This is the problem we have in the HVAC industry. Let's look at a comparison of package unit vs. split system HVAC.

Package Unit Advantage: The complete heating and cooling unit is assembled in a factory in a controlled environment. The charge of the refrigerant and the balance of motors are all installed in a controlled environment. This can ensure that the unit when installed will operate at its most efficient state. Only a duct system would have to be installed on site.

Disadvantage: All of the electronics controls and electrical motors are located outside in a harsh environment. If rain or snow gets into the unit it can cause many problems. The unit is also exposed to greater access by animals. Animals will find the warmest spot in the winter and that is inside the unit. The may chew on wires and destroy the insulation. Many package units will rust sooner that split systems due to the exposure to the elements. We find packages unit do not last as long as split systems in Birmingham, Alabama.

Split System Advantage: Components can be inside an attic or basement especially the electronic control pieces that are very sensitive to water. Split systems come in more configuration such as up flow, down flow or horizontal to easy the application needed. This allow greater customization of a project to achieve better results. Split systems are higher in efficiency than package units. Some split systems can be as high as 25 SEER while a package unit is from 13 -15 SEER typically.

Disadvantage: The installation is critical to system performance. We often say the most important day in the life of a system is the day it is installed. Poor installation will greatly reduce efficiency and the life of an AC. It is dependent on the installation technicians to arrange the components correctly. Match components based on the manufacturers design and then to properly adjust refrigerant levels to perform properly. Most split outdoor units come overcharged to account for a refrigerant lineset of 15 feet. If the distance between the indoor unit and outdoor unit is more or less the installation technician will have to adjust the charge.

Which is best? You now can decide!

Package Unit vs. Split System

Page 16: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

16

There is often times that a furnace and air conditioner could be replaced with a heat pump. Would you want to? What are the advantages of a heat pump over a furnace and air conditioner? Let's examine the pros and cons of each.

Furnace and Air Conditioner

Pros

Heat comes from natural gas, the good heat.

The air that comes from a furnace is usually 125 degrees.

You can get a blast of very hot air when you stand on top of a vent.

Furnace and air conditioner is usually cheaper than a heat pump.

Less parts and less repair issues

Cons

Heating costs are higher with a furnace and air conditioner

Heating costs are subject to change as the price of natural gas changes

Heat Pump

Pros

The cheapest way to heat a home.

Works best to maintain a constant temperature in a home

Cons

Heating is slower than with a furnace and air conditioner

Slow recover time for a home that is allowed to get very cold

Strip heats are very expensive to operate in very cold weather

So, what is a hybrid heat system? A hybrid Heat (or dual fuel) systems takes the advantages of the furnace and the heat pump and combines them. Wow, isn't that great? The advantage of each with very few of the drawbacks. Consider a hybrid heat the next time you need to replace your air conditioner. The comfort is great and the utility savings could pay for the upgrade.

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Air Conditioner vs. Heat Pump

16

A variable speed fan motor was originally, and still is, designed to eliminate the discomforts caused by ridiculous on/off part-time heating and air conditioning. We use it for the comfort it provides. The fact that it saves energy is a welcome bonus.

I don't make big fuel savings claims for several reasons. Lets say you have a 10 room home and two of those rooms are bone-chilling cold in the winter or hot and muggy in the summer. You have

How a Variable Speed Fan is Making the World a Better Place

Page 17: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

17

a variable speed fan motor installed and those rooms get warm in the winter and cool in the summer. You look at your energy bill and maybe you saved a couple of dollars. Or maybe you saved a lot. Maybe it cost you a couple of dollars more. The important point is that you don't have to retreat from very expensive real estate because your heating/air conditioning system is uneven and can't keep up.

A variable speed fan motor, when running at half-speed, (which it does most of the time) will use about one eighth the electricity that it takes to run the same motor at full speed. In other words you can run the variable speed fan motor eight hours for the same amount of money that you can run the same motor for one hour at full speed.

If your focus is strictly on energy savings, then turn the system off and freeze in the winter and roast in the summer. Or buy a tent. You'll save scads of money. Don't buy the Variable speed fan motor for energy savings alone. Buy it for comfort and healthy indoor environmental quality.

Residential air conditioning is a complex subject with definite and consistent rules. There are two components that must be removed from the air. These are heat and moisture. They are of equal importance. One of the air conditioning rules is:

The faster you run the blower, the more heat and less moisture you remove from the air.

The slower you run the blower, the more moisture and less heat you remove from the air.

With a fixed-speed on/off, part-time blower, there is a definite limit to how slow you can run the blower. A variable speed fan gives you the best these two choices by covering them both.

When the air conditioner compressor first comes on, a variable speed fan is running at a slow speed. That catches the latent (humidity) load and really pulls moisture from the air. At the same time, the cold air conditioning coil reduces the temperature of the air going over it. This immediately increases the blowers speed and sends the cool/dry air into your home. The speed of the blower stops increasing somewhere before it reaches full-speed. This is where it has found a balance between the humidity load and the heat load. A variable speed fan doesn't let go of the humidity load until it is down the drain and out of your home. Another interesting thing happens in Alabama, when homeowners install their first variable speed fan, they get worried because the blower seems to be running too slow. The reason for this is that a variable speed fan has found that the air is full of moisture and is busy helping the air conditioning system to remove it. When indoor relative humidity runs in the 75% range, there is a lot of moisture for a variable speed fan to work on. When the homeowner checks back the next day, the temperature of the air coming from the registers is cooler and moving faster and the indoor relative humidity is in the low 50% range.

It is disturbing to see the direction that the air conditioning industry is taking. Utility companies will kick-back a couple hundred dollars to the manufacturers if they can save a little electricity. So, what is happening? The pressure is on the equipment manufacturers to speed up their blowers. Remember, the faster the blower speed the more heat and less humidity is removed from the air. (some water is always removed) The thermostat reacts to temperature. Remove the heat and the temperatures drop. The thermostat shuts off the air conditioner and blower before enough moisture is collected. So you save electricity. This is false savings because the homeowner has to set the thermostat to a lower temperature setting in the attempt to get rid of that hot muggy

17

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 18: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

18

feeling. Because the thermostat is set lower, the air conditioner runs longer. Thus more electricity is used. The resulting lower temperature, combined with not enough humidity being removed, causes the home to feel cool and clammy. That moldy sock smell shows up as well.

The result is that speeding up the blower to ridiculous levels has produced what we consider is an uncomfortable situation. This might work in a laboratory setting, where nobody has to live all day. We don't think it works in the real world. Also, the high-speed blower strips moisture from the air conditioning coil and blows it down the ductwork. (mold?)

Here are facts that have not been taken into consideration. The slower the air moves across an air conditioning coil, the colder that coil is and the more moisture it collects. The faster that air moves across the coil the warmer it becomes and the less moisture it collects. The colder the coil's surface is, the better water will stick to it. The warmer the coil is, the less water will stick to it. Combine high air speed with a warm coil and you have water shooting down the ductwork. A variable speed fan solves most of this problem by limiting the air flow until the moisture is removed from the air.

During heating season a variable speed fan tames that high speed off/on blower. You only get the amount of air coming from your registers that you need. Air is always circulating. Always at a comfortable speed for the temperature being delivered. Your electronic air cleaner, filters, humidifier, UV germicidal lamps, and any other added equipment is always working at peak efficiency. Temperatures throughout your home become balanced. Drafts down stairways are eliminated. That cold draft when the blower first comes on is gone forever.

Everything attached to your heating/air conditioning system relies on the blower being on. Once the blower shuts off, so do your filters, electronic air cleaner, humidifier, ultraviolet (germicidal) lights and anything else connected to the system. When the blower comes banging back on, it kicks up dust, mold spores and anything else lurking in your ductwork. When this material gets back into the high speed air stream, it might end up in the best filter of them all, YOUR LUNGS!!

Mold cannot live without moisture. Many off and on fans blow hard enough to spray moisture from the air conditioning coil and down the ducts where it supplies the moisture needed to grow mold.

When a variable speed fan is operating, the average blower speed is much slower. This allows more time for UV lights to kill mold spores. Your filters or electronic air cleaner and UV lights operate about three times more efficiently. And, a super important point is that during air conditioning, much more moisture is removed from your home and it is much less likely to be blown off the A/C coil and into the ductwork where it can provide a great environment for mold.

These are the fan laws.

DEFINITIONS: S = Speed = RPM = Revolutions Per Minute. CFM = Cubic Feet Per Minute. W = Watts = Electrical unit of power. HP = Horsepower = Mechanical unit of power. 1 HP = 745 Watts = Conversion of electrical power to mechanical power.

Fan Laws: CFM2 = CFM1 x RPM2 / RPM1 or CFM is directly pegged to rpm.

If RPM is cut in half then CFM is also cut in half. If 1,040 RPM produces 1,200 CFM then 520 RPM will produce 600 CFM.

HP @ S2 = HP @ S1 x (RPM2 / RPM1)3 This demonstrates that the horsepower required to turn the fan is related to the cube root of the speed change. Or if the fan’s speed is cut in half, then the

18

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 19: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

19

amount of air delivered is also cut in half but the Horsepower required is only 1/8 of the original Horsepower required. OR, a fully loaded 1 HP fan motor running at 1,040 RPM and producing 1,200 CFM will only require 1/8 HP to deliver 600 CFM at ½ speed of 520 RPM. This demonstrates that the power required to turn the fan reduces a lot faster than the reduction in CFM being delivered.

Watts2 = Watts1 x (RPM2/RPM1)3 or Watts2 = Watts1 (CFM2/CFM1)3 This demonstrates that the electrical power required to turn the fan drops by the cube of the speed change. Or drop the speed (RPM) in half and the Power (Watts) required is 1/8 the original power required. Our example: 1/2 HP fully loaded fan motor running at 1,040 RPM and delivering 1,200 CFM requires 745 watts/2 or 372.5 Watts. Cut this motor’s speed in half and you cut the air delivery in half but the Wattage required is 372.5/8 = 46.6 Watts.

Therefore, a fan motor must run 8 hours at half speed to use the same amount of electricity as it would running at full speed for 1 hour.

Now lets bump this up-against reality. Lets assume that our example fan is in an average furnace. On an average winter day it runs about 1/2 of the time. It therefore uses 372.5 watts / 2 = 186 watt-hours of electricity. Now we install a variable speed fan that runs the fan full time. Now lets say there is a call for heat 3 times during that hour and the fan reaches top speed three times for 3 1/3 minutes each time (which it probably won’t) 10 minutes per hour = 1/6 hour x 372.5 watts = 62 watts and the other 50 minutes it uses 5/6 of 46.6 watts = 38.83 watts for a total of 38.8 + 46.6 = 100 watts per hour. For a savings of 86 watt-hours. And the home is comfortable, the air cleaner or filters are working full-time at much higher efficiency.

Monthly cost for a variable speed fan equipped fan at $0.10 per KWH = 86 watt hours x 24 hours x 30 days per month = 61,920 watt-hours or 61.9 KWH x $0.10 = $6.19 per month. If you ran the full-speed fan round the clock, it would cost 372.5 watts X 24 hours = 8.9 KW = $0.89 per day X 30 days per month = $26.00 per month. If you ran the full-speed fan ½ the time it would cost $13.00 per month.

This proves that a variable speed fan saves energy! Simply put, you can run a variable speed fan, for eight hours at half speed for the same cost as running it one hour at full speed.

19

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 20: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

20

20

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

The heart of your home’s HVAC system is the equipment selected to deliver conditioned air – your furnace, air conditioner, heat pump or boiler. However, as with the human body, a healthy heart cannot overcome problems associated with dysfunctional arteries.

Ductwork is the artery component of your HVAC system, channeling warm or cool air to various parts of the home as needed. When something goes wrong with an HVAC system, most people are inclined to think it’s a “heart problem” originating with the equipment. Frequently our trained

technicians pinpoint a ductwork issue as the cause.

Ductwork that is damaged, poorly sized or improperly installed can result in bad air flow, leaks and excessive utility bills. Our technicians usually can repair damaged ductwork without too much trouble. More problematic is when they encounter poor performance due to poorly sized ductwork or sloppy installation.

Over-sized systems run up utility bills and have trouble maintaining the desired air flow. Under-sized ductwork causes noise and strain on the system, leading to premature failure. Sizing ductwork involves calculations that take into account the local climate, size of your home, type of construction, insulation, windows and doors, shading and other factors. Incompetent or lazy contractors may ignore the guidelines and simply design ductwork by “feel” based on their experience. Often their “feel” involves cutting corners for the sake of a lower bid price. How would you like to employ a heart surgeon with that attitude?

A key measurement when sizing HVAC systems is CFM, i.e., how many cubic feet per minute of air movement the system will be required to handle. A common mistake made by some contractors who install combined heating/cooling systems is to size the system based on the heating load. Air conditioning requires more CFM, so when the same ductwork is used for both heating and cooling it’s wise to size the system for the air conditioning.

Another problem we frequently encounter is when homes are not properly zoned. Zoning refers to different rooms or areas with different air flow requirements for maximum comfort and efficiency. Some single-story homes can get by with a single HVAC zone, but most homes with two or more floors will need separate ductwork zones for each floor. That’s because hot air rises while cool air sinks. So a single zone in a multi-story house usually will result in uncomfortable temperature variations. The upstairs will be much warmer than downstairs. This is a common occurrence and one you’ve probably encountered either as a home owner or a visitor to a home with poor zoning.

All of this points to the importance of selecting an HVAC contractor that operates professionally and in accordance with the codes, standards and best practices of the field.

HVAC Performance Depends on Good Ductwork

BASIC EQUIPMENT STYLE

CHAPTER 4: RETURN AIR IS CRITICAL TO SYSTEM LIFE AND PERFORMANCE.

Page 21: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

21

21

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Competitive bidding often puts pressure on contractors to cut corners in ways that impact system performance. Just keep in mind that home owners who ignore best practices in favor of a cheaper price always end up paying a bigger price down the road.

The Problem with Leaky Ducts

Mid-summer has arrived. That means your air conditioning is getting a vigorous workout, and so is your monthly utility bill.

Does it seem like your air conditioner costs more to run than it should? Do you ever wonder why some rooms are very hard to cool? Or, why does your house always seems too dusty?

Any and all of these problems may be caused by leaky ductwork.

The leaks may be tiny and subtle, occurring at collars, joints and the air handling interface. If you live in a newly built home, the problem may stem from sloppy installation by the builder's crew. In older homes, it's a simple fact of life that over time joints come loose and duct tape falls apart. Even if it's a small hole, when the equipment is turned on, air pressure in the ducts increases 15 to 30 times. This forces air to escape, just like out of the narrow stem of a blown-up balloon.

Individually, none of these leaks may amount to much, but the cumulative effect is to dramatically reduce the operating efficiency of your HVAC system. One study done by the Florida Governor's Energy Office concluded that duct leaks increase total cooling and heating energy use in Florida by about 33%. Calculate how much money you can save if you could cut your HVAC expense by a third.

You can detect and fix minor duct leaks yourself. While the system is running, feel along the ducts for air escaping. When you locate minor leaks, you can plug them with silicone sealants made especially for duct systems. Hardware stores also sell special aluminized tape that is more effective than duct tape for wrapping around duct joints and bends.

Also be sure to keep the filters clean on any forced air system. They should be replaced about once a quarter for optimum performance.

While these do-it-yourself fixes will solve minor problems, more serious cases would benefit from an examination by our professional HVAC technicians. If you have return air duct leaks in an attic or crawl space, often they will draw that hot, dusty, moldy air into conditioned space. This not only wastes energy, it can be a health hazard as well.

Mold and mildew from leaky ducts can float through the air and accumulate on various surfaces. Over time this can lead to structural damage to walls and furniture. Worse, they can lead to serious health problems for people with mold and mildew allergies, or for people with respiratory ailments. Humidity given off from leaky air ducts may also cause rust in building metal components.

So if you live in an older home, get someone to clean your ductwork!

Have you ever had your ductwork cleaned?

Page 22: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

22

22

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Do I Need a Duct Cleaning?

Another question heard often is, do I need a duct cleaning? The answer to that could be different for many people. There have been studies conducted for and even a few against duct cleaning. How can this be? This seems like a pretty easy question yet it has many people giving many different opinions. Let examine what might make a duct cleaning more or less likely to be needed.

Residents: The health condition of residents in a home can play a factor. Why? Allergy issues can dramatically reduce the quality and the quantity of sleep. A home with a family with health issues and a low immune system is more likely to be negatively affected by poor air quality.

Duct Location: Air ducts in the floor will gather more dust and falling debris than duct in the ceiling or walls. Kids and animals are more likely to put things down in a vent. Once a cat had climbed into the ductwork and had babies. Would you want that cleaned and sanitized?

Duct Material: What the duct work is made from could also affect the need for a duct cleaning. Metal ductwork, that is insulated on the outside, will need less cleaning than duct board or any ductwork with insulation on the inside. Most square metal ducts have insulation on the inside while most round metal duct get insulated on the outside.

Age of Duct System: This is the category most refer when saying 'you need a duct cleaning' because it's old. That's an easy and very general answer. Age is not a prime factor as to getting a duct cleaning.

Homeowners Desire: Carpet does not have to be cleaned professionally. However, there is a whole industry created just for this reason. It's the homeowners desire to keep their home clean, fresh and nice that causes people to get their carpet cleaned. Duct cleaning is the same way. To know your home's duct work is clean, sanitary, fresh smelling and nice will require a systematic approach to maintaining it.

Many will often follow up their question with which type of duct cleaning do I need? We offer a standard and a deluxe cleaning. The more factors you have of needing a duct cleaning the more the deluxe will be better for you. The less factors (mentioned above) the more likely a standard cleaning will work for you.

Example 1: A home with square metal duct with insulation on the inside of the duct system in the floor of a family with pets and children that have allergy issues, you probably need a deluxe duct cleaning.

Example 2: A home with registers in the ceiling mage of metal round pipe with insulation on the outside of a neat keep clean home with no pets and only occasional visit from children could be very happy with a standard duct cleaning.

We offer duct inspection and would be glad to advise you on duct cleaning choices you could make.

Page 23: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

23

23

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

What is SEER for Air Conditioning? SEER stands for Seasonal Energy Efficiency Rating. That really didn't help you understand what it means though. It is the ratio of Air Conditioner performance to the amount of electricity it consumes. Easiest way to explain SEER is to equate it to miles per gallon (MPG) for a car. The higher the MPG or SEER the less energy it takes to do its job and that relates to less money.

This is a little simplistic answer to the question but it is all many people (other than Engineers) want to know.

Most people know the MPG of their car and are reminded of the money it consumes every time they stop at the gas station. Do you know the SEER of your AC? It probably consumes more of your money than your car but we never think about it. An Energy Audit and SEER calculation can tell you for sure.

What is a Ton of Air Conditioning?

"That house needs a ton of air conditioning!"

You might hear that sometimes in Birmingham, Alabama, but does it need a 'ton'? Well it could.

The term 'ton of AC' came from the early years when ice houses would literally take a 2000 pound piece of ice and it would be sat in a basement where air could be circulated over it to cool the air. This would then cool the building. I am glad that's not what we do today.

The amount of heat that it takes to melt 2000 pounds of ice is 12000 Btu's. A Btu is a unit of heat known as the British Thermal Unit. So in today's terms a 2 ton air condition can remove 24000 Btu's of heat from the air in a home. Most residential air conditioners start at 1.5 tons and go up by a half ton until 4 tons and then jumps to a 5 ton. A home needing more than 60,000 Btu's of AC would use multiple units to solve the air conditioning needs.

1.5 ton = 18,000 Btu's 2 tons = 24,000 Btu's 2.5 tons = 30,000 Btu's 3 tons = 36,000 Btu's 3.5 tons = 42,000 Btu's 4 tons = 48,000 Btu's 5 tons = 60,000 Btu's

What size is the unit in your home? Go check the model number. Most manufacturers will embed the size in the model number. The location will vary by manufacturer but if you see a 36 in the model number it is probably rated at 3 tons.

Did this help explain an old world term we still use today?

An Expert Interview About SEER

BASIC EQUIPMENT STYLE

CHAPTER 5: EQUIPMENT FEATURE AND SELECTION

Page 24: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

24

24

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Single Stage vs. Two Stage Compressors

The compressor is the heart of an air conditioning system. It pressurizes and moves the refrigerant back and forth from the condenser to the evaporator. It is probably the single most important and expensive item in your ac system. This single item can make the most impact on the operation of your home comfort system. Make sure to make the proper choices. Here are a few advantages and disadvantages. (single stage vs. two stage compressors)

Single Stage Compressors

Advantages:

Simple to work on

Cheaper to replace

Readily available for repairs

Disadvantages:

On/off control

The unit must run at full capacity even if only a small amount of heat is needed

Two Stage Compressors

Advantages:

Greater control

Greater humidity control

The first stage could be used on low needs days and save energy

Greater efficiency

Disadvantages:

Higher cost

More complicated to repair or replace

More complicated refrigerant charging process

Not readily available to replace and may have to be ordered

There is also a third choice that is moving in greater and great availability. It's called Variable Refrigerant Volume (VRV). It is much more expensive and allows for any need for ac to be exactly met by varying the cooling capacity of the unit from 30% to 100% of the size unit. It is the ultimate in efficiency, comfort and cost. Currently the only central AC system on the market is manufactured by Lennox.

Page 25: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

25

25

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Furnace Heat Chambers:

Aluminized Steel vs. Stainless Steel

Steel comes in several variations and each of them have unique qualities. Let us look at aluminized steel vs. stainless steel.

First, what is aluminized steel? Aluminized steel is steel that has been hot dip coated on both sides with aluminum-silicon alloy. This process assures a tight metallurgical bond between the steel sheet and its aluminium coating, producing a material with a unique combination of properties possessed neither by steel nor by aluminium alone.

Next, what is stainless steel? Stainless steel is a steel alloy with a minimum of 10.5% chromium by mass.

The economical aspect of these two varieties of steel is noticeable. Aluminized steel is cheaper than the stainless steel. This is because of the production cost of Aluminized steel is low when compared to the production cost of stainless steel.

The strength of these steels is also noticeable. The stainless steel is the stronger of the two. It is also more durable than aluminized steel. In respect to rusting, stainless steel does not rust. This is because of the presence of chromium. On the other hand, Aluminized steel can get corroded if the aluminum coat gets broken.

When comparing Aluminized steel vs. stainless steel, Aluminized steel has high thermal conductivity. Unlike the aluminized steel, the stainless steel has a high thermal expansion coefficient, which means that it could change shape when exposed to overheat.

Some of the common products made from aluminized steel include builder grade water heaters, ranges, furnaces, space heaters and grills. Stainless steel is also used in the manufacture of many things like high end kitchen appliances, cookware, storage tanks and even in the construction industry.

Summary

Aluminized steel is cheaper than stainless steel.

The stainless steel is stronger. It is more durable than aluminized steel.

In respect to rusting, stainless steel does not rust. Aluminized steel can get corroded if the aluminum coat gets broken or overheated.

Stainless steel heat chambers usually come with longer warranties.

Aluminized steel has higher thermal conductivity.

Stainless has aesthetics when compared to aluminized steel. This is why stainless steel is used in high end kitchen appliance, which add to its beauty.

Higher end products (like kitchen appliances) are made from stainless steel. Cheaper items use aluminum steel to imitate stainless.

Page 26: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

26

26

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Why is New Copper for Refrigerant Lines Important?

Have ever seen an old AC guy's pickup riding around with copper lines loose in the back? Refrigerant lines are very important part of the air conditioning system as it carries the refrigerant from the condensing unit to the evaporator coil and back. Great effort is involved from the factory and professional HVAC installers to remove all moisture from inside of an HVAC system. However, many uneducated ac guys will grab any piece of scrap copper and install it as the refrigerant lines in a system.

Only new, unused refrigerant lines should be installed. Why? New Copper lines designated for refrigerant use have had all the moisture removed from the inside of the line and sealed before shipping to the installation site. These copper lines will be marked as dehydrated on the outside. Moisture is the enemy of the compressor as any moisture that is inside the system will combine with the refrigerant and form an acid. This acid will then corrode the copper windings of the compressor motor. A gauge called a megometer can test the resistant of the compressor motor and give a reading as to the amount of damage a compressor has sustained from this.

Once the sealed copper is opened, moisture begins to creep into the lines. Especially in Birmingham, Alabama, humidity is very high and will begin to form small water drops on the inside of copper that is left unsealed. Never let unsealed refrigerant lines be installed on your new ac system. It will shorten the life of the system.

Page 27: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

27

27

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

The truth is NO. Many systems will run off of an old analog thermostat. SHOULD you replace your old thermostat with a digital thermostat? YES. Many features that did not exist 10 - 20 years ago are being built in to new thermostats and are not even mentioned as a feature.

1. Equipment Protection: Although a manual thermostat will send the signal to turn on the ac, it will not know if the equipment is ready and safe. The old thermostat could be turned off and on instantly and this would send the power to the compressor. This on and off instantly looks like a power surge to your equipment and can cause damage to control parts as well as the compressor.

2. Family Protection: Old manual thermostats have Mercury in them. This is very dangerous to humans if the thermostat were to be hit or knocked off the wall. (Kids will do crazy things when adults are not watching.)

3. Operating Efficiency: New thermostats have features built-in to manage the efficiency of the AC or Furnace. Controlling the primary or second stage only when needed or calling for the cheapest form of heat on a dual fuel system are two money saving examples of digital thermostats.

4. Programming: Many new thermostats have the ability to program a schedule to only operate when people are in the home 90% of homes fail to use this feature.

5. Auto Change Over: This one feature is the greatest item of all. Set the temperature at the thermostat, if heat is needed, it turns on the furnace. If cooling is needed, it turns on the AC. It’s just like the AC in any modern car.

I hope this help understand why we probably made a recommendation to upgrade your thermostat, but if you need more explanation, please ask the technician the next time he is in your home!

Do I Need a New Digital Thermostat?

BASIC EQUIPMENT STYLE

CHAPTER 6: ENHANCEMENTS AND CONTROLS

Page 28: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

28

28

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

I Have Elderly Parents Who Have

A Difficult to Operate Thermostat,

Can You Recommend An Easy to Use Solution?

Their are a large number of people who have a difficult to operate thermostat. We always recommend either the Nest Thermostat or the Emerson Blue Easy Reader Thermostat. Our clients who have these thermostats have been pleased with them.

We have spoke of the Nest in other posts, Click here to read about Nest.

There are many benefits of the Emerson Blue Easy Reader Thermostat:

Large Screen

Large Numbers

Simple one button and one function operation

Lighted display

Tall characters and one-touch mode buttons.

A hands on tutorial is available and recommended prior to our installation technician leaving your home to ensure you know how to operate easily. Click here for an operational video. If you are a member of the Freedom Comfort Club, you will receive a 20% discount off our normal price of $290. If we can help you with the installation of an easy to use thermostat, please call

205-444-4444.

Why have a Difficult to Operate Thermostat? Check out the Emerson Easy Reader.

Page 29: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

29

29

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Will a Nest Thermostat Work with my AC System?

We receive this call several times a week due to we install more Nest Thermostats than any other heating and air conditioning company in Birmingham, Alabama. The second generation Nest will work on 95% of hvac systems out there. We find that in our area that number is low and almost all systems we have seen will work with the Nest Thermostat. Go to Nest's website and check for yourself.

Also, many people will ask about the difference between the first generation and the second generation. Let me just summarize that the differences are significant enough to warranty only using the second generation unit. We use a first generation and two second generation units at our office. In fact, we can install a first generation unit but it will be the same price as we would have to special order a remanufactured first generation unit.

Does It Matter How You Achieve Efficiency?

Or that you get a lower power bill!

The HVAC industry throws the term efficiency around often and it can be confusing which meaning someone is referring.

ef·fi·cien·cy (From dictionary.com)

/ɪˈfɪʃ ən si/ Show Spelled [ih-fish-uh n-see] noun, plural ef·fi·cien·cies.

1. the state or quality of being efficient; competency in performance.

2. accomplishment of or ability to accomplish a job with a minimum expenditure of time and effort: The assembly line increased industry's efficiency.

3. the ratio of the work done or energy developed by a machine, engine, etc., to the energy supplied to it, usually expressed as a percentage.

Most often we refer to efficiency as it refers to how much it cost you on your power bill. Does it matter how a contractor achieves a 30% savings on your power bill. Well it could! Some efficiency can are cheaper to get than others. Very expensive items such as inverter technology variable refrigerant volume systems will often achieve only the same savings as less expensive items like duct return sizing and sealing. Wow!

Most people only want the savings and the power bill to go down, not how each component contributed. There are those people who need every detail in a system and that's ok. Let's list out the enhancements from most cost effective to improving efficiency.

1. Cleaning and Tuning Up a system is the most cost effective money saving item. 2. Regular Filter change (clogged filters damage more systems than any other item) 3. Return Air Proper Sizing (The return air is the most critical and most often improperly sized item in a system) 4. Duct Sealing 5. SEER Rating 6. Variable Speed Blower Motors 7. Dual Stage Compressor Technology 8. Inverter technology variable refrigerant volume systems

Remember, this is a list from most cost effective you to get a lower power bill and not saying which is better from a performance stand point.

Page 30: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

30

30

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

How Much Insulation Do I Need in My Home?

For this question you must understand the region you live in. In Birmingham, Alabama, we experience more cooling months than we do heating months. The state of Alabama HVACR board recommends at least R-30 of insulation. Alabama Power (our local utility company) would like for home owners to upgrade to R-60 of insulation in their attics. Insulation is a very cheap and quick energy saving item.

So how can you tell if you have R-60 or not? It depends on the material you use to insulate. The most commonly found loose fill insulation would need approximately 20 inches of depth. If you can go in your attic and see the rafters, you need more insulation.

Spray Foam Insulated Attics

I recently read an article by Allison Bailes, III, PhD about the HVAC pitfalls of spray foam insulated attics. It was a very good article and I wanted to share this with you. Spray foam insulation can be a good option for homeowners to use in attics to help with a home’s air tightness. However, Allison says that too many times installers make several mistakes that can defeat the purpose of the insulation or cause more serious issues.

Earlier this year she got a question about a home that had spray foam insulation in the attic. Nothing unusual about that. A lot of builders and homeowners are going with spray foam insulation because of the airtightness benefits. But then the questioner mentioned that the spray foam contractor had intentionally left big holes to the outside by not sealing the gable vents. The first pitfall is not thoroughly sealing the attic.

The next pitfall is that the house her friend asked about has atmospheric combustion appliances in the spray foam insulated attic. The spray foam contractor on that job saw the two furnaces in the attic and knew they needed combustion air from the space around them. If he had sealed up the attic completely, where would the furnaces get combustion air? That’s why they didn’t seal the gable vents. Now when those furnaces run, they can pull in the combustion air they need through those holes. But wait. If the homeowners are getting spray foam on their roofline to make the home more airtight, why would they leave big holes to the outside?

Oops!

A house is a system

It’s nice that the spray foam insulation contractor recognized the need for combustion air in that case. In many, they don’t get that far. Whether you’re building a new home or retrofitting an existing home, though, you’ve got to remember that the hip bone’s connected to the thigh bone; or, as we say in building science, a house is a system.

Newer homes have to meet building codes that help prevent this problem. If there’s atmospheric combustion inside the building enclosure, the HVAC contractor is required to install vents that are

Page 31: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

31

31

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

supposed† to bring combustion air into the room where the appliances are located. If the atmospheric combustion appliances start off in a vented attic, the building code doesn’t require those vents because the appliances are already connected to the outside and should get plenty of air.

Whether the home is old or new, however, anyone considering spray foam insulation would be wise to ask this question: What impact will encapsulating the attic have on the HVAC system?

This question applies to encapsulated crawl spaces as well.

If a home currently has atmospheric combustion, you’ve got two options: Don’t spray foam in the attic or replace the old equipment with sealed combustion, power-vented, or direct vent appliances. If the house isn’t built yet—or at least doesn’t have the HVAC equipment installed yet—make sure there’s no atmospheric combustion equipment going inside the building enclosure.

Remember: A house is a system.

My evaporator coil is leaking, why? or

Why do I have a leaking evaporator coil?

We sometime hear customers ask, Why do I have a leaking evaporator coil? I posed this question to our internal tech forum. The following are the comments and discussions that came from our service technicians. Please excuse the grammar as this discussion took place over text message.

Don: Forum Question: Why do evaporator coils leak?

Allan: Formic acid from the formaldehyde in the building materials eats through them

Allan: Dissimilar metal corrosion

Charles: And the copper tubing is thinner than it used to be

Justin: The galvanizing process is cheaper than it used to be

Allan: The government legislation that raised the minimum efficiency to 13 SEER resulted in the manufacturers using thinner copper to offset their cost of manufacture

Jeff: but less resistance to the effects of Formic acid corrosion. By resistance I mean time, time for it to eat through the thinner copper

Allan: A coil made 30 years ago would take 10-15 yrs to leak, one made today and installed on new construction wil last 3-7 yrs

Allan: Coils installed on existing homes will last longer due to the dissipation of the formaldehyde fumes in the building materials

Charles: So bringing in fresh air into the central air system could even help prolong a systems life

Allan: Yes but the air in the southeast would have to be run through a dehumidifier prior to being introduced into the system or your walls would mildew due to the increased humidity

Page 32: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

32

32

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Jeremy: Aluminum coils would be the cure for this but that's probably another discussion

Chris: A lack of maintenance will cause the internal pressures to be higher. This with the combination of thinner metal will accelerate leaks

I am proud of this discussion that resulted. We have worked really hard on better communication both internally and externally. This is how a company is suppose to grow and share the knowledge. Every employee may not have every answer but with a support system like this allows us to have a collective knowledge base bigger and better than any one guy. I am happy to share

this with you. If you need any further assistance call us at 205-444-4444. We look forward to helping you resolve your leaking evaporator coil problem.

Check out the next article in this series: How to Prevent Evaporator Coil Leaks?

How to Prevent Evaporator Coil Leaks?

Ninety-five percent (95%) of evaporator coil leaks are preventable. We see about 5% that are legitimate manufacturers defects. The major manufacturers state the failure rate is only 2%-3%. We believe that the humidity levels in the south cause the difference with longer AC runtimes than in other areas.

So, can you really prevent evaporator coil leaks? YES

A major cause of evaporator coil leaks, see article, is formic acid. So how can you prevent formic acid. This acid is produce when volatile organic compounds (VOC) react with the copper the coil is made from. VOCs are any household chemical that has the ability to react with other elements. Most VOC's come from the vapor released from cleaning agents, aerosol cans, air fresheners that put out a scent and not neutralize the smells, carpets, and any product that was created as a chemical process.

Reduce the use of VOC's.

If possible, bring in fresh air into the HVAC system to help dissipate the VOCs.

Use a whole house air purifier that is design to neutralize VOC through the use of ultraviolet light. The sun produces ultraviolet light naturally and it neutralizes VOC's naturally. The problem is sunlight does not happen inside your duct system and near your evaporator coil. A Lennox PureAir utilizes ultraviolet light to replicate the suns natural process and purify the air.

Reduce the acid build up. Regularly cleaning and servicing the coil will slow acid build up. This is one extra benefit most people overlook when it come to regular service, a longer coil life. Also a clean unit will run less internal refrigerant pressures from the compressor. Less pressure means less chance of a weak place in the coil becoming a leak.

Install a coil lamp in sight of the coil to keep growth and bacteria from covering the coil. This last tip is just as much about healthy air as coil protection but does help the coil life by reducing growth which clogs air flow between cleanings. Coil lights keep a coil that is maintained clean, but doesn't usually clean a dirty coil.

Call us today for more information and a coil inspection.

Page 33: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

33

33

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Why is Humidity Important to My Comfort?

Humidity; the amount of water in the air. OK, I heard that before but why should I care?

Comfort is a feeling and not a number on your thermostat. Comfort is a combination of the temperature and humidity. Some people set the thermostat on 78 degrees while others will set it on 72 degrees, Why? It has a lot to do with the humidity level. Lower humidity levels produce comfort at higher temperatures and higher humidity levels produce comfort at lower temperature. Every 10 % less Humidity is equal to 3 degrees of temperature comfort. Lower the humidity 20% in your home and set the thermostat 6 degrees warmer and still be just as comfortable.

A gauge called a hydrometer will read humidity and show it as a percentage. 0% means there is no water vapors in the air. 100% would mean its raining inside your home. (not really)

Where should the humidity level be in your home? Well it could depend on where you are located and any medical conditions you might have. But generally, in Birmingham, Alabama, I try to manage the humidity to 50%. General 45% to 55% is commonly recommended.

What is bad about high humidity? High water levels in the air make it easier for molds and mildews to grow in the air and then on your basement walls. Get a glass of ice water and sit it on a table. Is there a lot of condensation on the outside of the glass? Where did the moisture on the outside of the glass come from? it came out of the air. That one fact created the need for a new product, the coaster, in almost every house in America. That is a quick and easy test for humidity.

What is bad about low humidity? Low humidity can cause the human body to loose moisture and it usually is noticeable in the sinus passages. Have ever woke one morning to find it takes a good shower before you can breath well? That could be a sign of low humidity.

Newer thermostats, like the Nest (www.nest.com) will read and report humidity levels. Most older model thermostats were not equipped with hydrometers. Is your Home Comfortable?

MERV, Not Another Funny Texting Letters

MERV stands for Minimum Efficiency Reporting Value. It is a scale to show the performance of an air filter. The scale runs from 0 to 21. Most 'cheap' filters you find in the grocery store are rated approximately 2-3. 'Good' filters that are pleated are about a MERV 7-8. Filtrete makes a great air quality filter that gets an 11-12 rating. Any rating at 10 or above is considered a quality filter. Lennox has a filter that is rated as 'hospital quality' with a rating of 16. Clean Room technology like semiconductor manufacturing is a MERV 20-21.

Several Insane (but true) Things About Humidity

BASIC EQUIPMENT STYLE

CHAPTER 7: ALLERGY PROTECTION

Page 34: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

34

34

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

How Can I Know If I Have

Mold and Mildew in My Ventilation System?

How can I know if I have mold and mildew if I can't see it on the HVAC register?

Mold and mildew is not easily detected if it is not in a visible area in your home. One sign of mold and mildew problems in your HVAC ductwork are changes of indoor allergies. You may begin to sneeze, have nasal congestion, skin irritation and other health issues. These can become severe if mold and mildew are not properly removed. Indoor air quality (IAQ) is often low when you begin to notice a foul and musty odor coming from your heating and cooling system's return air ductwork. If you suspect any mold and mildew in your ventilation system, contact us at

205-444-4444 for an free inspection and removal proposal.

Air Duct Cleaning Service or a Better Air Filter,

Which is the Best Investment?

There are 3 filters in every home. The filter you should change but forget. The equipment captures and clogs up with anything the filter misses. And finally, your lungs will breathe in anything the filter and equipment misses and will trap it in your lungs. Which one are you relying on for your home?

The question is "which came first, the chicken or the egg?" We receive more calls and questions about air duct cleaning than high performance filters. Air duct cleaning would never be needed if a high performance

filters captured the dirt. After years of neglecting your duct work, the only choice you have is to clean it. Every duct cleaning service should only be done if a high performance filter is added. Would you go to a doctor with lung cancer yet be smoking in his lobby? How can a doctor cure someone who isn't willing to fix the cause. Air duct cleaning will not fix the dirt from returning. Air filters cure the disease and keep the cancer in the duct work in remission.

You answer the question, which is more important?

Page 35: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

35

35

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Clean Indoor Air; A Simple Guide to Indoor Air Quality

Filter The first level of indoor air quality (IAQ) is the filter. This is the step that removes particles from the air by pulling the air through an element, usually paper, to grab the impurities. The rating of a filter shows how it performs. The Minimum Efficiency Rating Value (MERV) scale starts at 0 and maxes out at 21.

Air Purifier Air Purifiers are a compliment to air filters. They are designed to eradicate any impurities that pass through the filter. The UV light in an air purifier will change the DNA structure of the organism not allowing it to replicate. This will kill it in that it can not grow any additional cells.

Duct Cleaning Some believe that cleaning air ducts is not necessary. But if cleanliness' is important, then you need to get any potential food source for bacteria out of our home. Check out this cheap and quick video of the inside of duct work as its being cleaned. There are different types of duct cleaning that range from a simple vacuum, to an agitation method such as a whip, a spinner ball and even a brush. All methods have their positive and negatives but any method done thoroughly will result in a clean duct system. If a simple duct cleaning does not get the air distribution system clean, consider replacing the duct work.

Duct Sealing The next stage of clean air is to seal all of the joints in the duct work. Why is this important? To keep the ducts clean requires that all the air pass through the filter and air purifier. The return that is not sealed will suck in contaminates from a crawl space, wall void or attic. There are a couple of methods of sealing ducts from metal foil tape, to mastic or a think paint, to new air based sealants like AeroSeal that pressurize the ductwork to find the leaks and slowly 'glue' the hole shut.

So what's next? A complete inspection from a service professional is a great step forward.

Page 36: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

36

36

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

What Wikipedia Can't Tell You About Sinus Allergy Issues:

Two nights ago my daughter had sinus allergy issues and felt real bad. She was mopey and whiney and could not breath well. Her nose was stopped up and she had to breath out of mouth. The tissue trail from constantly blowing her nose and missing the garbage can was beginning to pile up.

I began to think about her and thought something is wrong in my house. My house is a sanctuary of clean air and I own ever gadget, add on, enhancement or product to improve the air quality in a home. I believe in the products we install so much that I will install them in my home long before we will ever sell the items to a client.

I headed off to the attic to check the system for her bedroom area. Wouldn't you know it, the air filter was flashing an error signal that it needed cleaning. I usually have my company come out and service all my products every 6 months and maintain my home just like a Freedom Comfort Club member would receive. I want the same experience in my home as you get in your home. It allows me to check the work of my employees and quiz them on their understanding of high performance air cleaning products. It was time for service!

Since I wanted my daughter to feel better and sleep, I decided to get the electronic air filter operating at least through the night. I opened up the case and found a little build up on the activator pins. I went and found a Styrofoam cup to use to clean the pins. I understand my maintenance techs complaints as this is a very tedious task as there are about 80 pins that have to be cleaned. After about 20 minutes and a few finger pricks later I was done. This was not a full cleaning but I did get it operating.

I put the cover back on the unit and, using my iPhone, I remotely turned the thermostat down to get the unit to come on. It did and the light was not flashing anymore. Great!

I closed everything up turned off the light and headed back down the stairs. I went back to the thermostat and change the fan to the ON position. What good would it have been to have a filter or air purifier and then not turn it on when I needed it, TONIGHT! I checked on my daughter and we watched a little TV together.

About 2 hours later I notice she has fallen asleep and even though she is breathing loudly, I notice it is through her nose. Wow, this stuff we install really works. Being able to breath better can improve sleep dramatically.

The next morning I ask her how she feels and she gives me the thumbs up and appears to be feeling better. Although now I am telling her to get ready for school. I saved a sick day from school and my wife from rearranging her day to care for a sick child. That was worth the effort to research air purifiers, install, and maintaining it. Years of thought went into the decision but it saved the day and probably many more I have not even noticed.

Page 37: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

37

37

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

5 Ways To Deal With Crawl Space Air

The air in a crawl space can have a huge impact on a home’s durability and indoor environmental quality. A building science expert, Allison Bailes says that contractors have several options to deal with air in crawl spaces. In this article he details the five options and how they stack up for meeting your customers’ needs.

The air in a crawl space can have a huge impact on a home’s durability and indoor environmental quality

If you have a home with a crawl space—or are building or buying one—you have several options on what to do with that particular foundation type. Most crawl spaces are vented to the outdoors, but over the past decade, encapsulating the crawl space (as shown below) has gained favor among builders of green and energy efficient homes. It’s often seen as the best way to eliminate the moisture problems that often result from vented crawl spaces. But what do you do about the air down there?

Before we address that question, however, let me point out that encapsulated crawl spaces are great for humid climates, like the Southeastern US. In a dry climate, it may or not be worth the cost to encapsulate. So, as always, do what’s most suitable for your climate.

Basically, your options are to do one of the following:

The tried and false method of venting the crawl space to the outdoors

Putting a little bit of supply air from the HVAC system into the crawl space

Using an exhaust fan to move air from the crawl space to outside

Installing a dehumidifier

Let’s take a look at each of these methods.

Page 38: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

38

1. Vent the crawl space to the outside Do this in a humid climate, and you’re asking for trouble. The outside air that you bring into the crawl actually has more moisture in it than the crawl space air you’re venting to the outside much of the time. Although the psychrometric chart shows mathematically why it doesn’t work, a look into just about any vented crawl space in the Southeastern US proves that venting to the outside is often a disaster.

The photo of the moldy humidifier below is from a house that was only a year or two old. Although the home builder had installed closed cell spray foam insulation in all the above-grade walls and the attic, he left the crawl space vented to the outside. The result was mold growing on the HVAC system.

Let’s just say this is your worst option unless you’re in a dry climate and quickly move on to the better choices.

Conclusion: This is your worst option in humid climates. It’s probably also worst for most climates if the HVAC systems and ductwork are located in the crawl space.

2. Supply air from the HVAC system If you encapsulate the crawl space, adding a little bit of air from the HVAC system is probably the most common method used. If there’s already a duct system down there, it’s easy and inexpensive to do. The air from the system helps to dry out the crawl space air. But it also puts the crawl space under a slight positive pressure and the house under a slight negative pressure. Is that a problem? Not according to Advanced Energy‘s Closed Crawl Spaces guide:

In Advanced Energy field tests, the small crawl space airflow causes a negligible pressure effect that is far exceeded by the effects of duct leakage, stack pressure or wind-induced pressures in the building.

How much supply air do you need to add to the crawl space? Advanced Energy recommends 1 cubic foot per minute (cfm) for each 30 square feet of crawl space floor area. The International Residential Code (IRC) recommends 1 cfm per 50 square feet:

Conditioned air supply sized to deliver at a rate equal to 1 cubic foot per minute (0.47 L/s) for each 50 square feet (4.7 m

2) of under-floor area, including a return air pathway to the common

area (such as a duct or transfer grille), and perimeter walls insulated

If you go this route, it may work well in the summer if the air conditioner is sized properly. If the system runs long enough, it can provide enough dry air to the crawl space to keep the relative humidity below 70%, where you want it.

38

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 39: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

39

In the swing seasons, however, and in homes with oversized air conditioners, this method may not work well. Another thing about this method that I’m not crazy about is that you’re conditioning the crawl space based on the conditions in the finished space above. The crawl space has its own conditions, though, and may or may not respond well to controls in another place.

Conclusion: Although it’s the most common method of treating the air in encapsulated crawl spaces, it may or may not work well.

3. Exhaust air to the outside First, note that I’m not talking about the crazy idea to put large fans in the crawl space to exchange large quantities of air between the outdoors and the crawl. (Yes, companies really do promote this, and it’s a quick way to rot the wood in your crawl space.) I’m talking about a small exhaust fan, as described in the IRC. Here’s the language from the code:

Continuously operated mechanical exhaust ventilation at a rate equal to 1 cubic foot per minute (0.47 L/s) for each 50 square feet (4.7m

2) of crawlspace floor area, including an air pathway to the

common area (such as a duct or transfer grille), and perimeter walls insulated

So a 2000 square foot crawl space would need a 40 cfm exhaust fan. It’s pulling just a little bit of air from the crawl space. The problem is that you don’t really know where the makeup air for the crawl space is coming from. Yes, the code specifies a pathway for air to move into the crawl space from the house, but air doesn’t always follow those arrows in the diagrams. If the band joist isn’t sealed well, for example, it may pull a lot of the air from outdoors, which isn’t really what you want.

Conclusion: It could work but is probably less reliable than supply air from the HVAC system.

4. Install a dehumidifier In this method, you use a standalone dehumidifier for the crawl space. (Again, we’re talking about encapsulated crawl spaces only; although some people try, you can’t dehumidify the whole outdoors.) It’s controlled by the conditions in the crawl space, not the house above, so it this method will do the best job of keeping the crawl space dry. If you want dry air in your crawl space, a dehumidifier is the way to go. Yes, they do have drawbacks. You have to buy additional equipment. They require maintenance. If the drain fails, you

may have a bulk water problem in the crawl space.

If it’s a small crawl space, a standard dehumidifier that you can buy for $200 to $300 may be sufficient. For medium to large crawl spaces, however, it’s best to go with a more robust model, like the ones made by Therma-Stor. Their Santa Fe line is made for basements and crawl spaces. The dehumidifier photo below shows an older Santa Fe model made just for encapsulated crawl spaces.

39

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 40: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

40

Conclusion: Although more expensive, installing a dehumidifier is the best method for treating the air in an encapsulated crawl space.

5. Connect the crawl space to the house with a transfer grille Both of the quotes from the building code that I mentioned above include the following language:

…including a return air pathway to the common area (such as a duct or transfer grille)

What they’re saying is that if you pressurize the crawl space with supply air or depressurize it with an exhaust fan, they want the crawl space to be able to communicate with the house above to relieve the pressure. The easiest way to accomplish this is with a transfer grille right in the floor, as you see in the photo below. Advanced Energy isn’t a fan of this method, instead recommending that the entire floor be air sealed to isolate the crawl space from the house. There are some good reasons for this. If, for example, the intent of the opening is for house air to move downward (as in the case of the exhaust fan), the stack effect may win out if the crawl space isn’t perfectly sealed to the outside.

Another potential problem is pollutants in the crawl space air migrating into the house. These could be soil gases such as radon or fumes from paints, pesticides, or fuel stored in the crawl space. Also, if the crawl space access door is left open, it may not be discovered for some time. Meanwhile, the house is directly connected to the outside through that transfer grille.

Is it ever OK to install a transfer grille? Sure. In the house where I took the photo above, there’s no access to the crawl space from outside, and the owner (a guy who only recently learned the correct pronunciation of his name) doesn’t store hazardous chemicals down there (unless you consider wine hazardous).

Dr. Joseph Lstiburek, whose transfer grille you can see in the photos below, thinks that mixing house and crawl space air is fine in some cases: “If your crawlspace is ‘clean,’ connecting it to the rest of the house is ok. If it is not clean then you should not do so. In trashed crawlspaces sucking on them with a continuous exhaust fan works well. In clean crawlspaces up North, transfer grilles work just fine. In between and in the South, a very small amount of return air works fine with a transfer grille as does a small amount of supply air with a separate fan that does not blow cold air from the HVAC system but blows house air that is warmer and drier.”

The bottom line If I had to say one method was better than any other to deal with the air in a crawl space, it would be to encapsulate it and install a dehumidifier. Adding supply air from the HVAC system can be tricky and may let the crawl space humidity go too high in spring and fall. An exhaust fan may be OK in some cases. One thing I’d recommend above all else, though is to monitor the air. Install a digital thermo-hygrometer with a remote sensor so the homeowners can keep an eye on what’s happening to the humidity levels there.

40

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Page 41: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

41

41

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

We get asked to be a home warranty contractor about twice a year. We decline the offer because we offer a one price all-inclusive straightforward pricing. We are not designed to start a job as an estimate, have cost adjustments and complete that job with a much higher price. This is the typical "estimate" contractor mentality and home warranty contractors usually follow this model. An "estimate" versus a "proposal" is a big difference in the contractor world.

Usually home warranty contractors will try and charge for the extra items because the home warranty insurance company will not pay enough to complete the work. Watch out! "Estimate" contractors like to give a low estimates to win jobs only to go back to the homeowner with add-ons that make the job more expensive than complete proposals.

The insiders secrets to All the credits and rebates

available in Birmingham, AL

Federal Residential Energy Efficiency Tax Credits

This tax credit expired at the end of 2011. The American Taxpayer Relief Act of 2012 retroactively renewed this tax credit effective January 1, 2012, expiring again on December 31, 2013. Any qualified equipment installed in 2012 or 2013 is eligible for this credit. As in previous years, the cumulative maximum amount of tax credit that can be claimed by a taxpayer in all years combined is $500. If a taxpayer has already claimed a tax credit of $500 for purchases made in any previous year, they are ineligible for additional tax credits for any new equipment purchases. This credit applies to energy efficiency improvements in the building envelope of existing homes and for the purchase of high-efficiency heating, cooling and water-heating equipment. Efficiency improvements or equipment must serve a dwelling in the United States that is owned and used by the taxpayer as a primary residence. The maximum tax credit for all improvements made in 2011, 2012, and 2013 is $500. The cap includes tax credits for any improvements made in any previous year. If a taxpayer claimed $500 or more of these tax credits in any previous year, any purchases made in 2011, 2012, or 2013 will be ineligible for a tax credit. Building Envelope Improvements Owners of existing homes may receive a tax credit worth 10% of the cost of upgrading the efficiency of the building's envelope. Installation (labor) costs are not included and the credit is capped at $500 for all improvements. To be eligible for the credit, the improvement must meet the prescriptive requirements established for it under the 2009 International Energy Conservation Code (including supplements). The following improvements are eligible for the tax credit:

Insulation materials and systems designed to reduce a home's heat loss or gain

Exterior doors and windows (including skylights) --- no more than $200 in total credits can be claimed for windows in years 2006 - 2013

Pigmented metal roofs designed to reduce heat gain, and asphalt roofs with appropriate cooling granules.

Why No One Talks About Their Home Warranty Anymore

BASIC EQUIPMENT STYLE

CHAPTER 8: WARRANTY AND PRICE

Page 42: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

42

42

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Heating, Cooling and Water-Heating Equipment Taxpayers who purchase qualified residential energy-efficient property may eligible for a tax credit. The credit is equal to the full cost of the equipment up to the following caps:

Advanced main air circulating fan: $50

Natural gas, propane, or oil furnace or hot water boiler with an annual fuel utilization rate of 95 or greater: $150

Electric heat pump water heater with an energy factor of at least 2.0: $300

Electric heat pump which achieves the highest efficiency tier established by the Consortium for Energy Efficiency: $300

Central air conditioner which achieves the highest efficiency tier established by the Consortium for Energy Efficiency: $300

Natural gas, propane, or oil water heater which has either an energy factor of at least 0.82 or a thermal efficiency of at least 90 percent: $300

Biomass stoves that use "plant-derived fuel available on a renewable or recurring basis, including agricultural crops and trees, wood and wood waste and residues (including wood pellets), plants (including aquatic plants), grasses, residues, and fibers": $300

The Alabama WISE Home Energy Program provides up to $750 in energy efficiency rebates for homeowners in Cullman, Madison, Jefferson, Shelby, Morgan, Limestone and Lawrence counties. A $350 rebate is available to homeowners who install efficiency measures that result in an energy savings of at least 20% post energy audit, and an additional $400 rebate is available for eligible project improvements. Only single-family, owner occupied homes are eligible to participate in the WISE Home Energy program.

Residential Renewable Energy Tax Credit Established by The Energy Policy Act of 2005, the federal tax credit for residential energy property initially applied to solar-electric systems, solar water heating systems and fuel cells. The Energy Improvement and Extension Act of 2008 extended the tax credit to small wind-energy systems and geothermal heat pumps, effective January 1, 2008. Other key revisions included an eight-year extension of the credit to December 31, 2016; the ability to take the credit against the alternative minimum tax; and the removal of the $2,000 credit limit for solar-electric systems beginning in 2009. The credit was further enhanced in February 2009 by The American Recovery and Reinvestment Act of 2009, which removed the maximum credit amount for all eligible technologies (except fuel cells) placed in service after 2008. A taxpayer may claim a credit of 30% of qualified expenditures for a system that serves a dwelling unit located in the United States that is owned and used as a residence by the taxpayer. Expenditures with respect to the equipment are treated as made when the installation is completed. If the installation is at a new home, the "placed in service" date is the date of occupancy by the homeowner. Expenditures include labor costs for on-site preparation, assembly or original system installation, and for piping or wiring to interconnect a system to the home. If the federal tax credit exceeds tax liability, the excess amount may be carried forward to the succeeding taxable year. The excess credit may be carried forward until 2016, but it is unclear whether the unused tax credit can be carried forward after then. The maximum allowable credit, equipment requirements and other details vary by technology, as outlined below.

Page 43: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

43

43

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Solar-electric property

There is no maximum credit for systems placed in service after 2008.

Systems must be placed in service on or after January 1, 2006, and on or before December 31, 2016.

The home served by the system does not have to be the taxpayer’s principal residence.

Solar water-heating property

There is no maximum credit for systems placed in service after 2008.

Systems must be placed in service on or after January 1, 2006, and on or before December 31, 2016.

Equipment must be certified for performance by the Solar Rating Certification Corporation (SRCC) or a comparable entity endorsed by the government of the state in which the property is installed.

At least half the energy used to heat the dwelling's water must be from solar in order for the solar water-heating property expenditures to be eligible.

The tax credit does not apply to solar water-heating property for swimming pools or hot tubs.

The home served by the system does not have to be the taxpayer’s principal residence.

Fuel cell property

The maximum credit is $500 per half kilowatt (kW).

Systems must be placed in service on or after January 1, 2006, and on or before December 31, 2016.

The fuel cell must have a nameplate capacity of at least 0.5 kW of electricity using an electrochemical process and an electricity-only generation efficiency greater than 30%.

In case of joint occupancy, the maximum qualifying costs that can be taken into account by all occupants for figuring the credit is $1,667 per 0.5 kW. This does not apply to married individuals filing a joint return. The credit that may be claimed by each individual is proportional to the costs he or she paid.

The home served by the system must be the taxpayer’s principal residence.

Small wind-energy property

There is no maximum credit for systems placed in service after 2008.

Systems must be placed in service on or after January 1, 2008, and on or before December 31, 2016.

The home served by the system does not have to be the taxpayer’s principal residence.

Geothermal heat pumps

There is no maximum credit for systems placed in service after 2008.

Systems must be placed in service on or after January 1, 2008, and on or before December 31, 2016.

The geothermal heat pump must meet federal Energy Star criteria.

The home served by the system does not have to be the taxpayer’s principal residence.

Page 44: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

44

44

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Manufacturer Rebates Most manufacturers offer a rebate for purchasing their equipment. The rebates are used by the distributors when the demand slows. That means that the incentives are greater during the off season rather than in the peak season. Replacing an AC in the winter or a furnace in the summer could be virtually FREE after the rebates and the price difference from the peak season. And Yes, manufacturers do raise their prices as demand increases. The best rebate I have seen currently is $2000 from Lennox. Rebates expire so check our website for current offers.

Utility Refunds Alagasco offers refunds for upgrading your furnace or gas water heater. Currently there is a $200 refund for replacing your furnace with a newer model furnace. Why do they offer this? To keep you as a customer. They do not want to lose you to their competition, the electric companies. In fact, Alagasco has a 'dump the pump' offer of a $1000 refund if you convert from a heat pump to a gas furnace and air conditioner.

Other incentives from Alagasco include: Furnace (Replacement): $200 Dryer (Replacement): $100 Natural Gas Range/Cooktop (Replacement): $100 Water Heaters (Replacement): $200 Tankless Water Heaters (Replacement): $200

Alabama power does not offer any refunds but will finance air conditioning systems and place this on your regular bill.

Buyer's Clubs Costco is a great retailer and has put more resources into the HVAC category. Lennox and Costco have partnered to be the exclusive HVAC Brand offered through Costco. This is a very impressive arrangement as Costco has always been known for the quality approach to merchandise as opposed to lowest price while quality suffers as the other retailers have done.

Costco and Lennox then approve a local Contractor to install and service these members based on a very rigorous selection process with the goal of Costco member satisfaction as the primary concern. I am excited to be part of this program in the Birmingham, Alabama area. We feel it is an honor and some recognition for our years of hard work.

Members earn a CASH card rebate through Costco. The amount is based on the size of the Lennox Equipment up to $1000. Executive members earn even more as this purchase is reported to Costco and is subject to the 2% additional rebate annually. American Express Costco Card members can earns the rebate from AMEX as well if it is paid for on their AMEX card.

Finance Savings If you do need to finance, the best offer we have seen is currently a 0% interest rate for 60 months. This is about a 20% savings when you analyze the time value of money.

With all these choices above, no wonder it can cause people to worry about making a decision. Some people delegate this information to the professions and some people abdicate the decision and hope they don't get taken advantage of. You now can confidently know what is in your best interest.

Page 45: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

45

45

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Costco members earn CASH from HVAC Installation

Costco is a great retailer and has put more resources into the HVAC category. Lennox and Costco have partnered to be the exclusive HVAC Brand offered through Costco. This is a very impressive arrangement as Costco has always been known for the quality approach to merchandise as opposed to lowest price while quality suffers as the other retailers have done.

Costco and Lennox then approve a local Contractor to install and service these members based on a very rigorous selection process with the goal of Costco member satisfaction as the primary concern. I am excited to be part of this program in the Birmingham, Alabama area. We feel it is an honor and some recognition for our years of hard work.

Members earn a CASH card rebate through Costco. The amount is based on the size of the Lennox Equipment up to $1000. Executive members earn even more as this purchase is reported to Costco and is subject to the 2% additional rebate annually. American Express Costco Card members can earns the rebate from AMEX as well if it is paid for on their AMEX card.

How Much Does an Air Conditioner Cost?

One of the first questions homeowners want to know when they call our company is: How much does an air conditioner cost? Although this is a very difficult question to answer, I will try to do my best here to explain some general pricing guidelines.

in their vehicle within the first five years of purchase, why do so many people elect to get so many upgrades? The answer is because most people understand the importance of getting what they want the first time so as to not have any regrets down the road. Because most Americans spend over 30 minutes a day in their vehicles, they want to make sure their vehicle will provide them with comfort, quality, longevity, and ease of use.

These same principles typically apply to most air conditioner shoppers. Understanding that they are going to depend on their air conditioner everyday for as long as they live in their home, as well as the fact that picking the air conditioner with the right options the first time is critical as to ensure maximum enjoyment with minimum maintenance, most shoppers elect to get the air conditioner that will make them happiest in the long-run. Unfortunately, some people only focus on the initial price of the air conditioner with the only goal of finding the "cheapest" contractor, therefore sacrificing efficiency, quality, warranty, and performance, which inevitably leads to regret, especially considering that unlike a vehicle, an air conditioner cannot be traded in if one is dissatisfied and disenchanted.

Now that you hopefully understand the vehicle analogy, I will list some of the most common "add-ons" found in the purchase of an air conditioner:

Humidifier

Hybrid

Ventilation

Dehumidification

Air filter

Page 46: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

46

46

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Air purifier

Coil purifier

Variable speed fan

Variable refrigerant volume

Two stage compressor

Aluminum or copper evaporator coil

As you can see, there are many options available, and when someone receives a quote from our company, we thoroughly examine each option as to educate the homeowner on the option's benefits as to identify its overall importance to the success of the project.

When an inquiry is made as to how does much an air conditioner cost, complexity of the installation is also a key factor. We have at least three different packages we offer our customers. Unlike most air conditioner companies, we will do as much or as little as our customers would have us do. This flexibility leads to less stress and more savings for the customer.

What's the Price of a Heating and Cooling System?

One of the first questions we get is "what's the price of a heating and cooling system?" This is usually the first concern a home owners have as soon as the need comes to their mind. The problem with answering this question is the complexity that a complete comfort system can have with all the styles, brands and types of units that are available. I'll do my best to give you some realistic price ranges that you may spend. (these prices are averages and estimations , and can vastly change depending on the region, the company, manufacturer, warranty, etc)

Just the Box: Sometimes, we will have a home owner that only wants to buy the equipment. Although there are many more costs involved with a comfort system, there are people out there that want to do everything themselves and buy every single component individually. I am reluctant to state these price ranges because you must keep in mind these price ranges do not include installation, filter system, duct work, etc.

Low or Basic Efficiency (13 SEER or less): $1,500-$3,000

Mid Grade Efficiency (14 - 15 SEER): $2,000-$4,000

High Efficiency (16 SEER and higher): $3,500-$8,000

Basic Install: This typically includes: minimum code compliance, removal of old equipment, existing filter system, duct transition, evacuation, and refrigerant charge.

Most heating and air conditioning systems, not including other options, will have a price range of $4,000-$8,500. (This, like everything else mentioned in this article, is contingent on a many other factors)

Page 47: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

47

47

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Basic Install plus Filter: This includes everything mentioned in the basic install plus the filter and return modification (Most returns are sized for the home design and not the air flow needs. We have to upgrade the majority of homes returns)

Typical Price Range: $4,500-$9,500

Complete with Existing Ducts: This includes everything found in Basic install with filter, but it also includes duct sealing, air flow balance and electrical upgrades.

Typical Price Range: $5,000-$11,000

Complete with ducts in a home that currently does not have a central system: This includes everything found in Basic install with filter, but it also includes new insulated duct work, gas piping of furnace, venting, electrical wiring and condensation drain system.

Typical Price Range: $6,500-$14,000

Prices For Other Options: High Rated Air Filter: Filter prices are between $500-$3,000 for most home.

Air Purifier: Air Purifiers kill the living organisms in the air that the air filter does not remove. They cost between $1,400-$2500

Coil Purifier: A Coil purifier or 'stick light' is a small ultraviolet device mounted within a few inches up to 12 inches of the evaporator coil. It stops bacterial growth before it can turn into spores and get air born. Prices range from $300-$1000.

Heat Pump: Most heat pump upgrades cost between $1000-$2000, plus additional cost for electrical upgrade or wiring

Hybrid / Dual Fuel: Most hybrid upgrades cost between $800-$1600. Hybrid is all the benefits of the heat pump with out the loss of the good heat of a gas furnace.

Dehumidifier and fresh air: Dehumidification can get very expensive, depending on the size, location and fresh air requirements. Most cost $2000-$5,000.

Humidifier: The price of adding moisture to the air can vary. A simple bypass may be from $300 and a steam model can be expensive as $1500.

Thermostat: Most thermostats cost between $100-$600. More expensive controls can be remote capable, programmable, learning or iPhone controllable.

Page 48: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

48

48

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Although all of these numbers and prices are very general, I do hope this article helps you to have a better feel for air conditioning pricing and what to expect when you start going through your comfort system buying process.

Can I Get A Lower Price?

We get this question occasionally and it is human nature that people want to make sure they are getting the best deal. Many companies and technicians usually try to avoid any questions about price and money.

But here is the reality of price, you can get a lower price for systems or repairs. We offer 5 choices for any repair and the trade off with price and warranties is direct. The more premium and permanent choices allows us to stand behind our work for longer periods of time. Temporary repairs usually come with temporary warranties.

Many companies show one price and give no options to the consumer. Many time this approach is a more forceful tactic.

Now this leads to the next logical question. "Why do we charge what we charge?" There are many items that contribute to the price that is charged. The price of the part or system and the labor to install it are the top items but not the only factors in price. The real costs of any company will include all the items such as workers comp, insurance, office personnel, gas, advertising, training, and the list goes on and on. We must manage our fixed overhead cost to 30% to have any chance of not going out of business.

If a company does not operate professional and does not price to handle these expenses then they will struggle to stay in business to honor any future warranties or obligations. When a company starts cutting expenses they typically cut the training and education. These leads to a downward spiraling effect. Most low cost companies are usually low training companies. Technicians start guessing and guessing as to the problems with systems and this could lead to a consumer paying for repairs that do not fix the problem and only hide the problem for weeks or months or even till next season. Then next year the problem comes back and the consumer must pay again for the next band aid. We prefer the permanent repair approach and a full system evaluation is needed to complete this.

Ask yourself if the price the most important item or is the proper repair is the most important item.

Can I Just Replace my Furnace or AC Without Doing Both?

Yes, you can. Many so called sales people will say you have to replace both at the same time. That's usually not true. What is true is there are time you should consider replacing both.

1. Hybrid Heat. Hybrid heating system is the most efficient way to heat a home. It uses electricity to heat when that is the cheapest and switches to a backup source, usually natural gas in Birmingham Alabama. So instead of replacing, upgrade.

Page 49: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

49

49

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

2. Control System. Most home owners do not realize that all the controls for the AC are located inside the furnace. If you replace the AC and not look at the controls in the furnace, you could turn around tomorrow and still not have any air conditioning. How mad would you get to spend thousands of dollars to have an AC installed to have the company say you must pay more for it to work?

3. Fan. The air movement throughout your home is done from an electric motor mounted in the furnace. What good is it to have AC if you can not distribute it throughout the house?

4. Efficiency. We all heard the saying a chain is only as strong as its weakest link! In the HVAC world, the efficiency is only as high as the lowest component. A 18 SEER compressor in a 10 SEER unit will not reach its full potential savings. A new AC on the wrong evaporator coil could be less efficient than the old unit.

5. Cost Savings. It will cost more to replace both the Furnace and AC today but will be less than the total of doing all the items individually. A little more today could save moreover then next few years.

I Have a Friend in the HVAC Business

Using a friend may not be a good idea. We just received a call from a home owner who had his friend, who previously worked for us, put in a system. We let the guy go because of ethical and honesty problems and I can tell he has not changed. The new equipment is having trouble after only 2 months. The friend probably gave him a good deal but now the homeowner can not get the warranty part repaired. He has been waiting, trying to get back in touch with his friend, but he may have to pay someone else to fix his new 'good deal' unit. This is just one of the stories we here at least 10 times a year.

What could happen now? By hiring the unlicensed friend, the home owner is not protected by the state held bond all HVACR contractor must post with the state of Alabama. The city did not inspect the job as no city license or permit was obtained.

This spells out the bad that could happen to the homeowner, but what could happen to the friend? Friends mean well, but you could be putting a friendship at risk. It is against the law if he is not licensed in the appropriate trade. Also consider these problems:

He probably will not have liability insurance to protect your home in the event there is a problem. What if he cuts corners and causes a fire? Are you sure he has the money to rebuild your house for you?

You could also cost him his job as doing 'side work' is against most company policies. We have to terminate someone every year due to 'side work'.

Workers compensation law states that if a worker is injured while working on your property, you will be liable for his medical bills and weekly pay until he is able to work again. Homeowners insurance does not cover workers compensation issues usually.

In this case, the state will also investigate and if the contractor was not appropriately certified and licensed, he could pay a state fine and if it is a serious offense he could face jail time. How is the

Page 50: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

50

50

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

friendship going to be when your work cost a friend a huge penalty and jail time. Don't expect to be invited to next years Christmas party!

Why do we choose a friend over a legitimate company? Trust! We use a friend because of the trust factor. I have a guy I prefer to use for my carpentry work. I will use him for anything I need around the house. Its not about getting a cheap price. Its because I trust him since I have used him. Most people use a friend for trust reasons but only a few use a friend to cheat the system and win by getting something for nothing. But are you? Quality can suffer with cheap prices and you have very little retribution against cheap work even with a friend. It is easier to use someone we know over a stranger. But how can you trust a company if have not used them before?

The Misconception About

'Getting 3 Bids"

in the HVAC industry! Old wise tale or old wives' tale (from www.yahoo.com .... something that a lot of people once believed but has since been exposed as a myth.) says to "get three bids" before you buy anything! In these busy times, people can't spend the time they used to waiting on a HVAC contractor to fit them in, or worse, not even show up for an appointment.

But, why are you getting three bids? So you are not being taken advantage of and get what you need and want! Yes. The modern day information age has a better solution.

Research and find the best company

Get a whole house energy audit and heat load analysis and a complete plan

Have one company, that you trust because of their online reviews, prepare at least 3 choices to solve your problem. An ultimate package (if comfort and allergy protection was the only concerns), a band aid solution (money or price is the only concern), and a compromise package which blends the important items from both packages...

Any of these three choices will be far greater than you current HVAC system. Choices are the future of all businesses.

If you are currently getting 3 bids from any of our competitors, discover a better more professional

way by calling me at Freedom Heating and Cooling at 205-444-4444.

Page 51: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

51

51

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

If it’s sweltering outside, the last thing you have in mind is cranking up the furnace. But cooler temperatures are not far away. It’s time to schedule a heating season combustion adjustment, professional cleaning and safety check.

Gas Furnace that is clean and safe for the long cold winter

An annual heating system “tune-up” is one of the best home maintenance investments you can make. Homeowners who neglect it tend to pay the following penalties:

Fuel bills rise as much as 10-15% as a result of inefficient equipment operation. It’s like having a fireplace that burns money. Our service technicians will perform a variety of tests to measure the combustion efficiency of your system both before and after tuning it up.

Accelerated equipment wear. Annual maintenance extends equipment life as much as 5-10 years for your furnace.

Our long experience tells us that about 75% of all HVAC system repairs we do could have been avoided with regular maintenance. Repairs cost a lot more than maintenance, and breakdowns never happen at a convenient time.

Most important, annual heating inspections can save your life and those of your loved ones. Small cracks in a heat exchanger or problems with the flue system could allow deadly carbon monoxide gas to seep into your home. Dozens of people in the U.S. lose their lives each year to these tragedies. Our trained service technicians know how to spot danger signs in the system.

Modern HVAC systems are very sophisticated. Our well-equipped service technicians have an array of electronic measuring devices and tools to properly service these units. You can trust their professionalism and experience to do the job right.

Heating Season Tune-ups Save Money, and Maybe Your Life

BASIC EQUIPMENT STYLE

CHAPTER 9: MAINTENANCE AFTER INSTALLATION

Page 52: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

52

52

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

While heating inspections can be done at any time, early fall is the most popular time for most home owners to schedule these visits. Many of our clients have their fall heating inspection done as part of an annual service agreement. They receive priority in scheduling and discount pricing for any repairs not covered by the agreement. A service agreement also is a good way to ensure you don’t forget about scheduling heating system maintenance. We’ll remind you. If you are not on our list, give us a call to ask how you can be included.

Beyond a certain point even the best maintenance cannot save an antiquated system. Efficiency improvements over the last few decades have been so dramatic that if your furnace is more than 20 years old, it’s quite possible that it would make economic sense to replace your present system even if it is still operating okay. Ask our service technician to perform an energy audit of your home to see how many years of energy savings it would take to pay back the initial cost of a new installation. Also ask about low-cost energy efficiency improvements that can be obtained from devices such as automatic flue dampers and programmable setback thermostats or internet compatible thermostats.

What is the Freedom Comfort Club?

The Freedom Comfort Club (FCC) Membership is different from a tune up. The tune-up consists of a one time appointment. It does not come with the amenities of the FCC membership. Manufacturers recommend you have your unit serviced every six months to prevent your system from breaking down at the most inconvenient time. This is why we offer our services to you in a package deal. Having your system serviced improves the efficiency and life of your heating and cooling unit.

The Comfort Club Membership is a two tune up and cleanings per year agreement. You will receive an additional 20 percent discount on parts and labor if any repairs are needed. All Diagnostic Calls (even emergency calls) will receive a $50 discount from our current $89 price (without Maintenance agreement.) You will never have to wonder if you will find some one to help you if you have a membership. It places you in a top priority status with Freedom Heating and Cooling. Your agreement is transferable. So if you move, be assured that it will follow you.

So feel comfortable knowing that we are here to help. You will not be charged any weekend or overtime additional charges with this service agreement. There is 24 hour emergency and weekend service at your fingertips, just dial 205-444-4444. Contact me if you are interested in enrolling.

Page 53: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

53

53

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Tankless vs. Tank Water Heater

We hear the questions about tankless vs tank water heater from time to time. The latest question is "which is better in Birmingham, Alabama?" The following are the advantages and disadvantage of each.

Tankless Water Heater Advantages: A tankless water heater never runs out of hot water. You do not have to wait for the tank to reheat to use. Most are higher efficiency and will have less utility cost per gallon if hot water.

Disadvantages: Converting to a tankless water heater is more expensive than in a new construction application. Gas piping may have to be resized. Vent piping typically has to be changed from a tank water heater. Tankless water heaters can be more than double a tank water heater. A new tankless water heater is about $2000 to $5000 depending on the application.

Tank Water Heater Advantages: A tank water heater is simple to change out if there is a need for a new unit. A tank water heater could be as low as $1000 if very little additional items are needed. Quick install; when your tank water heater goes out, you want hot water again NOW! A tank water heater an be changed in about 2-3 hours. A tank water heater will have higher utility cost to keep water hot even when no one is needing it. A home owner who is not home often or a tank water heater in a retirement home, could be running for weeks without any need. Therefore, how the home owner will use the water heater is important.

Disadvantages: A tank water heater will often run out of hot water. Waiting for the tank water heater to reheat is sometimes 30 to 45 minutes. A large family would have a difficult time letting everyone have a hot shower. A tank water heater last about 10-15 years. A tankless water heater should last 20 plus years.

I hope this is helpful to you and we welcome your call if you are in need of a water heater repair or replacement, tankless or tank water heater.

Electric Water Heater vs Gas Water Heater We get the question of should I have an electric water heater or a gas water heater? There are several advantages and disadvantages to each. The following is a quick and simple explanation of the difference between an electric water heater vs gas water heater for consumers in Birmingham Alabama.

Electric Water Heater Advantage: One huge advantage in Birmingham, Alabama is Alabama Power will typically offer a free electric water heater for anyone converting from gas to electric.

Disadvantages: Slow recovery time to heat fresh cold water. It could take 1 to 2 hours to fully reheat a large electric water heater tank. A large electric circuit is required to be dedicated to an

BONUS: WATER HEATERS AND HOME ENHANCEMENTS

Page 54: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

54

54

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

electric water heater. This could require an upgraded electrical panel to be installed. This would greatly raise the price of a water heater installation.

Gas Water Heater Advantages: Gas water heaters can quickly recover and reheat water so hot water can be used again quickly.

Disadvantages: Gas water heaters must be vented to the outside. Years ago single wall vent pipe was used. This is no longer meeting code, so a simple water heater replacement could require the upgrade of your vent pipe to double wall B-type pipe. Gas water heaters have a flame. This flame can be dangerous if a gas water heater is placed in a garage or storage area. In fact, new codes require water heaters to be placed on an minimum 18 inch tall stand when placed in a garage or an area where gasoline or other flammables could be stored. Call your local permit office and ask the inspector for the requirements in your area.

One solution, which I have in my home, is to use a gas water heater as the primary water heater. Then after the water is heated, it is dumped into an electric water heater to keep warm until needed. My home has a 40 gallon gas and a 40 gallon electric installed in a utility closet. It is not uncommon for my children to take 30 to 45 minutes showers and never complain of water getting cold. This set up allows water to be heated as quick as it is used. We have never had a situation where we have run out of hot water no matter how long a shower lasts. As my kids might say "awesome"!

How Hot to Set Your Water Heater?

Water heater temperature settings of hot can be different for every person. However to be the most energy-efficient, you should set the water heater so that you can take a shower with only hot water. This could create a problem with not having enough hot water for a complete family. Most people use the solution of turning the water heater up to a very high-level and mixing it with cold water as it comes out of the faucet to make the water temperature comfortable. This is very wasteful as a water heater will be heating water 24 hours a day to that high temperature. It might only need to be extra hot for a one or two hour period each morning as a family gets ready.

Safety is another reason to set your water heater to a moderate level. If you have small children, you should set your water heater to a maximum temperature that will not scald your kids. This will help ensure your family is not injured from accidentally turning the cold water off first before turning the hot water. Many children are harmed each year from scalding while taking a bath.

Having a large enough water heater to provide hot water to your family by using only hot water is the best method. This saves on energy costs, and safety of your family. To find a proper setting may take several adjustments. This could take several weeks to allow your water heater time to adjust to the new lower temperature.

Page 55: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

55

55

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Whole House Generators Can Keep You Out of Trouble

"I want a whole house generator to get me through the next tornado and hurricane season." I hear this statement a lot so I thought I would share some things to consider as you plan your project.

Size: Whole house generators basically come in sizes, ranging from 10-48 kilowatts. You determine your size based on the amount of electricity your home consumes. The majority of newer homes in the United States are built with 200-amp electrical service. Older homes have a 100-amp panel. Go to your breaker box and see the breaker at the top and see the rating number. (Be careful, electricity is dangerous.) In other words, the MAXIMUM amount of electricity your home can consume is 200-amps. In reality, it never really uses every amp of electricity. On hot summer days, the air conditioner

consumes almost half of all electricity. At night, most homes barely use any. If you absolutely, positively want to replace every, single amp, you’ll need a 48-kilowatt whole house system, which generates all 200-amps of electricity. In most cases you can save significant dollars by choosing a smaller model, which could still power the whole house with a little planning and load balancing. Check the data specs to see what size AC the unit will start. (Startup of an air conditioner takes a huge amount of energy compared to just running it.)

Phase The vast majority of homes use 120/240-volt, single-phase electricity. Three-phase electricity is designed for commercial applications, such as restaurants and banks. Don’t even consider a commercial generator for a whole house application unless you truly have 3 phase in your home.

Speed or RPM's 1800 or 3600 RPMs. This is a little tough to explain but here I go. Electricity has a frequency to its alternating current (AC). In the US and especially in Birmingham, Alabama where I am, AC current is at 60 Hertz or 60 cycle per second. Europe operates on a different cycles (50 Hertz). To generate the 60 cycles per second you must turn the generator at a speed that is a multiple of 60 to produce this. A generate made for Europe will not work in the US. (A least not without major modifications). Basically, the engines on a 1800 RPM generator run at half the speed of other whole house generators. The reduced speed consumes less fuel, makes less noise and wears less, resulting in less maintenance and increased life span.

Enclosure Just like air conditioners, natural gas or propane powered generators are fully enclosed to protect the generator from the weather, rodents and everything else. Aluminum enclosures cost a little more, but they also outlast their steel counterparts. If you live near the coast – where salty air is notorious for corroding metal – consider an aluminum enclosure. The steel enclosed generators are little louder, but they also cost less.

Why do you need a generator? Consider your personal circumstances and the need for electricity. Are there health issues? Are you willing to leave your home and go to a hotel or family's house if electricity is out for an extended time? Some years we have little to no outages but other years we have gone weeks in some areas. Do you have valuable items in your home that extreme cold or extreme heat would ruin?

Page 56: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

56

56

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Paintings, furniture, antiques. If a heat spell came and your items were ruined due to lack of AC, it would make the generator options look very cheap.

I hope this is a good start on your generator journey.

Ductless AC in Every Home Means Comfort and Savings.

Ductless technology is the fastest growing segment in the U.S. HVAC industry. While some home owners might think of ductless systems as primarily single-zone installations, like for a sunroom or addition, ductless systems are increasingly being used as a solution for a variety of multi-zone installations.

Ductless Ac

To raise awareness of the wide variety of installation capabilities, Mitsubishi Electric US Cooling & Heating Division (Mitsubishi Electric) has rolled out its Ductless on Every Job Campaign. Their goal is to encourage home owners to consider ductless on every application by educating them on unique scenarios where ductless can be a solution to a customer's need. With limitless installation possibilities for ductless, Mitsubishi Electric is spreading the word that ductless technology can open the doors for home owners to have the most comfort and savings.

Here are just a few cases where home owners can consider a ductless solution:

Older Homes. Because no ducts are required and the systems can be installed with little to no demolition, ductless technology is especially beneficial for homes that were built before air conditioning was widely available and contain no existing ductwork. A ductless system allows for the preservation of the home's structure, including historic architectural details like high ceilings and moldings.

Bonus Rooms, Additions, and Lofts. Often when homeowners add on to their existing homes, their HVAC system isn't sized to accommodate this additional load. Ductless systems are an ideal supplement to a home's existing HVAC system. With the new MXZ-5B system, you can cool or heat up to five zones, which is ideal for larger additions and entire floors. At 42,000 Btu/h and 3.5 tons, no other system on the market operates at this size and capacity.

Page 57: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

57

57

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Empty Nesters. When the kids go off to college or move out of the house, there may not be as many rooms being used. Empty nesters don't want to waste energy and money by cooling and heating unoccupied areas of their home. The zoning capabilities of a ductless system give homeowners individual control over the temperature in each room. You can turn off the units in the kids' rooms when not needed and easily turn them back on again when they visit.

Cold Climates. Ideal for homes located in areas with cold and windy winter days, their exclusive Hyper-Heating (H2i™) technology provides full heating capacity to minus 4 degrees Fahrenheit. The advanced INVERTER compressor delivers precise amount of comfort to the zones as required. This technology eliminates cold and hot spots and allows homeowners in the coldest of climates to live comfortably in every room of their house, all year round.

These are just some of the many scenarios where a ductless solution can give contractors a competitive edge.

Protect Yourself and Your Electronics From Lightning Strikes Humans and animals have an ingrained fear of lightning – and with good reason. Lightning kills hundreds of Americans each year. A single lightning strike can carry enough electricity to power 10 million homes for a month!

Being inside your home during a lightning storm is safer than being outside. Yet you are not completely safe on the inside. Electricity can travel through various unprotected pathways inside the home. Water is an especially good conductor of electricity, which is why you should avoid taking a bath or shower while a storm rages outside. Also avoid using the telephone or touching the metal of any electronic device when lightning is in the vicinity.

After your personal safety, you need to safeguard various electronic devices that are so much a part of our modern way of life. A lightning strike on your home or even nearby can “fry” thousands of dollars’ worth of home equipment in an instant. Here are some tips to help you avoid that.

Your best protection is to invest in a whole-house surge suppressor. This device protects everything that’s plugged in, such as your refrigerator, stove, and other large appliances. This line of protection spares you the hassle of using individual surge protectors all of your home.

If you are anticipating a storm, or see lighting nearby, unplug all power cords and cables. This isn’t always possible, but if you are at home during a severe electrical storm, consider doing it for your major electronic devices and appliances. Most lightning storms are short lived so they won’t be without power for long.

Invest in high-quality surge protectors. (We can recommend and sell them to you.) Cheap surge protectors may be okay for inexpensive electronic devices such as clocks, but you want maximum protection for computers and other expensive electronic equipment. Not all power strips come with surge protection and many that do have limited capacity.

In the event of a strike on your home, replace all surge protectors. Some high-end surge protectors can withstand a lightning strike, but most will not offer protection against a second surge. You won’t know that for sure until you’re hit by lightning again.

Obtain a universal power supply (UPS) for computers. If your power goes out, a UPS will keep your computer powered long enough to shut it down properly. This will prevent potential data loss and corruption in case of an abrupt shutoff. Use line-specific protectors for cable lines and phone cords. Lightning can damage these even if the power source is protected.

Page 58: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

58

58

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

Make sure you have GFCI outlets installed in your kitchen and bathroom. These will protect you from shock by automatically shutting down if in contact with water, or if an unsafe level of electricity is running through it. If you have them installed already, have them checked during your yearly inspection for full functionality.

Consider installing a backup generator system in case of power outages. This is especially important if you depend on your computer or other electronics for your livelihood.

Make sure your home is well-grounded. Homes with lighting protection should at least have two grounding rods, along with special terminals and connectors to route the surge to the ground and avoid a fire.

Lightning is not the only electrical threat to your lives and property. Scientists warn against the potential for catastrophic solar flares capable of knocking out major power grids. One event in 1859 nearly electrocuted some telegraph operators. Another solar storm in 1989 knocked out the power grid for almost Canada’s entire Quebec province.

Our trained and licensed technicians can evaluate your home and recommend protection consistent

with your budget and your lifestyle. Spend a little money with us now to avoid thousands of dollars in

repair and replacement costs in the future.

Page 59: 1 THE ULTIMATE HOMEOWNER’S GUIDE - Freedom Heating & …...It also includes air duct cleaning services (duct cleaning). Air Duct cleaning service is the process of vacuuming out

59

59

The Ultimate Home Owner’s Guide to Designing an HVAC System ©2013 Don Johnson

So, what is the next step? There are many points to design the best heating and cooling system.

We are here to help you through this process. Don’t allow any air conditioning service guy to sell

you a part and leave you to pick up the pieces. Make sure the proper design process is followed

and you will be happy for many years. Remember as mentioned in a previous articles, you will

have to keep your HVAC system for many years and if you are not happy you can not trade it in

like you can a car.

Call us at 205-444-4444 and a trained comfort advisor will be glad to assist you in this design and

upgrade process.

BASIC EQUIPMENT STYLE

CONCLUSION


Top Related