Download - AM-11.65.022 V3F16L Troubleshooting
V3F16L DriveTroubleshooting
V3F16 drive AM-11.65.022© 2002 KONE CorporationAll rights reserved.(Draft -) 2003-01-21TROUBLESHOOTING GUIDE FOR DRIVE SYSTEM V3F16L
LIST OF CONTENTS
1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 INTERFACES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 CHECKING THE DRIVE CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 START FAILS IN RDF OR INSPECTION DRIVE (FIRST RUN) . . . . . . . . . . . . . . . . . . . . . . 6
6 SETUP DRIVE FAILS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 PROBLEMS IN NORMAL DRIVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8 SPECIAL CASES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9 READING DETAILED FAULT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410 ADDITIONAL PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
11 VERSION HISTORY AND APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
APPENDIX A. V3F16L parameter table
APPENDIX B. V3F16L drive fault codes
1. Brake cable connector, XBR32. LCE cable connector, XS3 (safety cir cuit, start permit, brake supply)3. Motor cable connector, U-V-W4. Supply cable connector, T1-T2-T3 5. LWD motor current cable connector, XW1 6. MAP tachometer connector, XLG1 7. Tachometer cable connector, XG1 8. LCECPU cable connector, XL1 (flat cable)9. Motor thermistor connector, XT1 10. Braking resistor cable connector, XBRE2
1008801.wmf
7
10
12345
6
89
© 2004 KONE Corporation AM-11.65.022All rights reserved. 1 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
1 GENERAL
This instruction includes additional information and troubleshooting hints to solve problemsduring RDF, inspection, setup and normal drive in elevators with drive module V3F16L. It isment for specialists, trainers, field support personnel and troubleshooters.
This instruction is valid with the following elevators (in accordance with EN 81-1).
Refer to the elevator level installation manuals for the prerequisites, preparations andcommissioning.
NOTE! Chapters from 4 to 8 are following the commissioning sequence. During thecommissioning the elevator is set to drive differend drive modes in the followingorder: (1.) RDF drive, (2.) Inspection drive, (3.) Setup drive, (4.) Normal drive. Whenany of these drive modes fault try to solve the problem by following the order of thenumbered checklists.
In order to get the elevator drive correctly in the next drive mode the earlier drive mode(s)must operate without problems.
1.1 Related documents
Refer to the elevator level instructions for the prerequisites, safety chain checking, setting thenon-drive features, special features, commissioning and especially for the working safety.
• AM-01.03.001 Use of fall arrest systems on elevator construction and modernisation sites• AM-01.03.002 Take 5 - Electrical safety when working on elevators• SO-11.65.014 Specification and order instruction of V3F16L drive module 769900G0X for
KONE MX synchronous motors and LCE control• ASG-11.65.009 Preventive maintenance instruction• AS-11.65.009 Instruction to replace V3F16L module• AR-10.22.006 Spare parts manual, MonoSpace• 784393: Drive parameter table• 804611: Drive fault codes• 713490: LCE fault codes• 813131: LCE user interface menu for no cabinet elevators
Elevator Control system
Elevator level manual
MonoSpace® LCE / No Cabinet
AM-01.01.026TranSys™ AM-01.01.044Fure#1 and #2 AM-01.01.038MicroSpace AM-01.01.047
© 2004 KONE Corporation AM-11.65.022All rights reserved. 2 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
2 SAFETY
Note the following safety items when working with LCE electrification and V3F16L drivesystem:
• General KONE safety regulations must be followed during the work. All safety measuresfor normal elevator installation must be implemented and local safety regulations followed.
• Refer to AM-01.03.002 “Take 5 Electrical Safety When Working on the Elevators”. TheTake 5 safety initiative is designed for installation, servicing, maintenance andmodernisation work done on the elevators.
• Safety must be ensured with additional fences or guarding, depending on the siteconditions.
• Personal safety equipment must be used as required.• Do not work on the different levels in the elevator shaft at the same time.• The covers of the maintenance access panel and shaft electrification panels must be kept
closed when not working with them.• Do not continue the work after opening the covers of the Shaft Electrification Panel or
drive module before checking that all circuits are safely de-energized or protected (SEP,V3F16L, resistor module and possible optional modules).
2.1 Safe de-energizing method
• Turn OFF the main switch (220) in the MAP-panel.• Lock and tag the main switch.• Wait 5 minutes.• Check that there is no voltage (AC) in terminals of the main switch (220), opposite of the
riser terminals. Check operation of the tester before and after the test. (Main PowerSupply VAC.)
• Close the door of the MAP-panel.• Remove protection covers of the electrification panels in the elevator shaft.• Check that there is no voltage (DC) in the intermediate circuit. Also in the motor and
braking resistor terminals. Measure from the connector XBRE2, between terminals 1 and3 against the ground (In V3F16L module). Check operation of the tester before and afterthe test. (Intermediate circuit VDC)
WARNING Inverter drives usually remain energised for about 5 minutes after the power has been disconnected. DO NOT work on the drive, hoisting motor or braking resistors until you have verified that this energy has been discharged.Test equipment must be set to the 1000 V DC range. The test equipment must be checked before and after the test to ensure that it functions correctly.
P15000017.wmf
© 2004 KONE Corporation AM-11.65.022All rights reserved. 3 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
3 INTERFACES
Pos Name Pos Name1 Signal 8 N / 230 VAC2 Signal 9 Start permit3 LWD 10 Safety chain4 GND 11 N / 230 VAC5 Motor current 12 Thermistor6 GND 13 Brake 1 / Brake 27 230 VAC 14 Braking resistor
MU
V
W
PE
GXG1/1
XG1/2
T1
T2
T3
PE
XT1/1
XT1/2
1
6
1: T
11: 1
11: 2
XBL+
XBR+
XB-
XBR3/1
XBR3/2
XBR3/3
DRIVEMAP
XL1
X4
LCE230
XD1/1
XD1/2
XD1/3XD1/5
XD1/7
XS3/1
XS3/2XS3/3
XS3/5
XS3/7
XL5/1 XW1/1XW1/2XW1/3XW1/4
T1
T2
T3MODULE385
XLG1/1
XLG1/2
XL6/1
XL6/2
PE
XL5/2XL5/3XL5/4
379
306XBRE2/1
XBRE2/3
LCECPU375
1023305.wmf
LOPCB12346
7891011
12
13
14
© 2004 KONE Corporation AM-11.65.022All rights reserved. 4 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
4 CHECKING THE DRIVE CONNECTIONS
Always ensure that the connections at the drive module are completed correctly.NOTE!Keep the motor supply cable by a minimum distance of 100 mm from any other parallel cables
(especially tachometer cable). A blinking speed LED (or tachometer LED) at MAP may indicate a poor earthing.
Check that:• Cables are routed correctly inside the drive module.• The wires at the connectors are looped to avoid gravity water entering connectors. This is
valid for cables entering the drive module from the top.• Cables are connected properly:
– no loose connections– check by pulling the wire
• Connectors are clean.• Earthings have been done.• Stress relief is in place. Cables (coming from the lower part of the drive) are secured with
cable ties.• LCECPU cable connector is locked properly.
1021392.wmf
X LG1
385
385/XW1
385/XG
1
385
1
1
1
1
1
1
1
© 2004 KONE Corporation AM-11.65.022All rights reserved. 5 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
5 START FAILS IN RDF OR INSPECTION DRIVE (FIRST RUN)
Always check the diagnostic codes first and clear the error log history. Refer to the AppendixC 804611 (Drive fault codes) and 713490 (LCE fault codes).
5.1 Motor does not rotate (no power to the motor)
1. Check LEDs at the MAP (see chapter 10.10).2. Check the cable connections (see chapter 3, Interfaces)3. Check the safety chain.4. Check that both the RDF and inspection drive are not
active at the same time.5. Check the LCE parameter 1_95 (drive interface selection).
It must be 1.6. Check that all three phases of the main supply are
powered.
5.2 Motor rotates a little (elevator jumps) and stops
1. Check the tachometer polarity and motor phase order.2. Check that the cables at the connectors XLG1 and XG1 are not inverted.3. Check that the motor cable connectors are tighten at the drive.4. Check (measure) stator resistance between the three phases (motor supply cable must be
disconnected from the drive module). Check the motor supply cable. If the connections atthe motor end are correct, repeat the same measurements and checks for the brake.
5. Check and re-adjust LWD.6. Check the LWD signal by checking parameter 5_1.
• (0=empty car), signal is correct.• (- -- --), no signal. Check the LWD.• (116), no possibility to adjust the LWD because of no LWD connection. Check the LWD.• (-5), no connection from the drive. Check the cable between LOP-CB board (XL5) and
drive (XW1).7. Check the balancing.8. Check parameters 6_1...6_4.9. Check that the machine brakes are energized.10.Check the air gap of the brakes.11.Check that the car or counterweight is not stucked (DBG or other mechanical reason).
SPEED> 0.1 m/sD42
START PERMITD41
CONTACTORD40SHAFT DOORCONTACTD39CAR DOORCONTACTD38
CLOSE DOORCOMMANDD37
DRIVE NEEDD38
V3F16 OKD35
SAFETY INPUTD49 1021395.wmf
© 2004 KONE Corporation AM-11.65.022All rights reserved. 6 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
6 SETUP DRIVE FAILS
Always check the diagnostic codes first. Refer to the Appendix C 804611 (Drive fault codes)and 713490 (LCE fault codes).
In order to get the elevator drive setup correctly the RDF and Inspection drive modes mustoperate without problems.
The setup drive must be performed with the empty car. After completing the setup drive checkthat the car runs to the lowest, intermediate and topmost floors with rated speed.
Check that the battery in the car top connection box is connected (car roof electrification iscompleted correctly) and the inspection drive unit is switched to normal mode.
6.1 Starting of the setup drive fails
6.1.1 Motor does not rotate (no power to motor)
When the RDF mode is on:
1. Check that the parameter 4_1 indicates correct elevator mode.2. Check that the LEDs 77:N, 77:S, 61:U and 30 are on. Note: Drive does
not register door zone (30).3. Check that the LCE-drive flat cable is in good condition.
When the elevator is switched to normal mode:
1. Check that the safety input LED is on.2. Check that the LED V3F OK is on.3. Check that the LED LIFT IN FAULT lit.
A starting sequence will be activated within a minute (LEDs Driveneed, Close door command, ... light).
6.1.2 Motor rotates slightly and stops at the door zone
1. Check the diagnostic codes.2. Check the location of the final limit switch (51), (the operation point of the limit switch
should be at least 120 mm from the floor level). Start the setup drive as close to the final limit switch as possible (car is not too close to61:N switch).
3. Check LWD (menu 5_1 must show 0%).4. Check that there is no unnecessary friction in the sliding guide shoes of the car or
counterweight.5. Try again from a lower point at least three times.
61:UD43
30D56
B30D55
61:ND54
77:ND16
77:SD53 1021403.wmf
SPEED> 0.1 m/sD42
START PERMITD41
CONTACTORD40SHAFT DOORCONTACTD39
CAR DOORCONTACTD38
CLOSE DOORCOMMANDD37
DRIVE NEEDD38
V3F16 OKD35
SAFETY INPUTD49 1021400.wmf
© 2004 KONE Corporation AM-11.65.022All rights reserved. 7 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
6.2 Elevator stops during the setup drive
1. Elevators with drive software version 0.63 and later, check a subfault code 118. See chapter 9.
2. Adjust the distance between 61-switches.3. Check the magnet switch condition4. Check that the switches are not:
• activated by the bolts of the guide rail joint• activated by a diverting pulley (TranSys)• disturbed by a motor• exposed to mechanical vibrations• handled carelessly• placed to wrong position
5. Check safety chain (it may open during setup run).6. Check the floor distances. If the distance is higher than 5 metre a dummy floor is required
(61 magnet).7. Check the number of floors. Two floor elevator requires a dummy floor
(61 magnet).
6.3 Elevator drives to the topmost level but not complete the setup drive
6.3.1 No line indication (- -- --) displayed on the user interface after setup
A missing line-indication means that the setup drive was not registered in LCE.
After checking the possible faults re-start the setup drive.
1. Check the location of the final limit switch (51), (the operation point of the limit switchshould be at least 120 mm from the floor level). Start the setup drive as close to the finallimit switch as possible (car is not too close to 61:N switch).
2. Check the operation of the 77:U and 77:S switches.
6.3.2 No 118 indication displayed on the user interface after setup
A missing 118-indication means that the setup drive was not registered in V3F16L.
After checking the possible faults drive the car to the 51-switch with RDF, raise the car slightlyby opening the machine brake and re-start the setup drive.
1. Check the location of the final limit switch (51), (the operation point of the limit switchshould be at least 120 mm from the floor level). Start the setup drive as close to the finallimit switch as possible (car is not too close to 61:N switch).
2. Is the LCE-drive flat cable in good condition.
5-10 mm
P04000127.wmf
61:N
61:U
==
130m
m=
=
FFL
© 2004 KONE Corporation AM-11.65.022All rights reserved. 8 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
6.4 Car passes the lowest floor after a successful setup drive
1. Perform the setup drive again. Start the setup drive as close to the final limit switch aspossible. The lowest floor was not correctly registered in drive.
7 PROBLEMS IN NORMAL DRIVE
Always check the diagnostic codes first. Refer to the Appendix C 804611 (Drive fault codes)and 713490 (LCE fault codes).
In order to get the elevator start in Normal drive correctly the RDF and Inspection drive mustoperate without problems and the Setup drive must have been performed successfully.
Problems listed below may not be noticed during the RDF, Inspection or Setup drive becausethe full speed or motor current has not been used.
• weak power supply (one of the phases dead)• problems in elevator shaft mechanics• an unnecessary friction between the sliding guide shoes and guide rails• vibrations (caused by poor LWD adjustment or tachometer cable routed too close to motor
supply cable)• machine brakes are not fully open• poor balancing
7.1 Start fails
1. Check LED-indications at the MAP (see chapter 10.10).2. Check parameters from 6_1 to 6_4.3. Check that the machine brakes are energized and the air gap.4. Check and re-adjust LWD if necessary.5. Check the balancing.6. Check shaft friction.7. Decrease the acceleration parameter 6_21.
7.2 Elevator runs to light direction, but not to heavy direction
1. Check that the machine brake opens fully and that the machine brake linings are not incontact with the traction sheave surface during the drive.
2. Check the balancing.3. Check LWD signal at topmost and lowest floor. If there is a big difference re-adjust LWD.4. Check that there is no unnecessary friction in the sliding guide shoes.
SPEED> 0.1 m/sD42
START PERMITD41
CONTACTORD40SHAFT DOORCONTACTD39CAR DOORCONTACTD38
CLOSE DOORCOMMANDD37
DRIVE NEEDD38
V3F16 OKD35
SAFETY INPUTD49 1021395.wmf
© 2004 KONE Corporation AM-11.65.022All rights reserved. 9 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
7.3 Stopping fails (quick stop)
Elevator is stopped when slowing down to the floor or elevator stops suddenly during normalrun by a machine brake (this is also known as a “quick stop”).
1. Check fault codes and safety circuit.2. Check balancing.3. Check LWD (menu 5_1 must show 0%).4. Check that there is no unnecessary friction in the sliding guide shoes.5. Decrease the acceleration 6_20.6. Increase final jerk distance, deceleration factor, load parameter 6_3 or K-parameters.NOTE! If the drive software version is 0.49 or 0.55 see also FL-11.65.030 or
FL-11.65.031 (TranSys).
7.4 Poor stopping accuracy
The stopping accuracy must be checked in normal operation conditions by driving to eachfloor from both directions. A normal operation condition can be achieved by running the carfew minutes from a terminal floor to another.
NOTE! If any changes were done for the positioning switches or their magnets perform anew setup drive.
1. Check distance between the magnets and magnet switches (vertical and horizontaldistance).
2. Check error code 118. See chapter 9.3. Adjust the distance between 61-switches.4. Check the magnet switch condition5. Check that the switches are not:
• activated by the bolts of the guide rail joint• activated by a diverting pulley (TranSys)• disturbed by a motor• exposed to mechanical vibrations• handled carelessly• placed to wrong position
6. Check distance between the floors (if more than 5 metre a dummy floor is required).7. Check balancing and LWD adjustment.8. Check LWD signal at topmost and lowest floor. If there is a big difference re-adjust LWD.9. Check DBG of car and counterweight guide rails where any increased friction occur.
5-10 mm
P04000127.wmf
61:N
61:U
==
130m
m=
=
FFL
© 2004 KONE Corporation AM-11.65.022All rights reserved. 10 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
7.5 Unnecessary relevellings
NOTE! If any changes were done for the positioning switches or their magnets perform anew setup drive.
1. Check distance between the magnets and magnet switches(vertical and horizontal distance). If necessary change a distance130 mm to 125 mm.
2. Check error code 118. See chapter 9.3. Adjust the distance between 61-switches.4. Check the magnet switch condition5. Check that the switches are not:
• activated by the bolts of the guide rail joint• activated by a diverting pulley (TranSys)• disturbed by a motor• exposed to mechanical vibrations• handled carelessly• placed to wrong position
6. Check if any problems occur with the lowest floor stopping accuracy. Check the location ofthe final limit switch (51), (not too close to the landing). Perform the setup drive.Start the setup drive as close to the final limit switch as possible (car is not too close to61:N switch).
7. Check tachometer cable (earthing, distance from the motor supply cable must be100 mm).
8. Change tachometer.
7.6 Vibrations
1. Clean the guide rails and add oil to the guide rail lubricators.2. Check the shaft mechanics (DBG and guide rail joints).3. Check air gap of the machine brake.4. Check the tachometer wiring.5. Measure motor resistance (all three phases should be equal). Motor supply cable must be
disconnected from the drive module.6. Tighten motor terminals at the drive.7. If low frequency, vertical vibrations occur, check and adjust if necessary tacho filter time
6_23 (5...50) and D-factor 6_22 (2...6).8. If the speed varies, check tachometer cable (earthing, distance from the motor supply
cable must be 100 mm).9. Change tachometer.
5-10 mm
P04000127.wmf
61:N
61:U
==
130m
m=
=
FFL
© 2004 KONE Corporation AM-11.65.022All rights reserved. 11 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
8 SPECIAL CASES
Always check the diagnostic codes first. Refer to the Appendix C 804611 (Drive fault codes)and 713490 (LCE fault codes).
8.1 LWD is not adjustable
1. Check the cable and connections between the drive (XW1) and MAP (XL5).2. Check the user interface (LOP-CB) board LEDs +24V, +5V, +12V and -12V.3. Check that gain potentiometer is in middle position before adjusting the offset. 4. Check the cable between MAP and load weighing device (maximum length of the cable
without special amplifier and electrification is 9 metres).
8.2 Roll-back
1. Check balancing and adjust LWD.2. If any roll-back occur increase load parameter 6_3 or K-parameters.
HINT: Increase start delay parameter to a maximum value temporary to check if any roll-backor jerky start occur during the start.
8.3 Heavy car or high travelling height (start fails in normal drive)
High travelling heights (from 25 to 40 metre).
1. Adjust the LWD. Run the elevator about 10 minutes and re-adjust the LWD. Run theelevator 10 minutes again and re-check the LWD settings.
2. Check balancing, re-adjust LWD if necessary and check guide shoe / shaft friction.3. Reduce acceleration parameter 6_21.4. Adjust parameters (e.g. increase 6_3 with 50 kg steps) and check that the fault codes over
current (0102) or motor over temperature (0104) does not appear.5. Increase door time (to reduce heating of the motor).6. Check that the elevator shaft ventilation works correctly.
© 2004 KONE Corporation AM-11.65.022All rights reserved. 12 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
8.4 Hot elevator shaft and installation conditions (for example glass shaft)
Start fails, motor gets over heated (0104). Improve cooling and / or apply a sun protection onthe glass surface in top floor area to prevent sun heating machine, drive and SEP.
1. Measure machine surface and elevator shaft temperature.2. Inform the building owner if temperature of the elevator shaft is higher than +40C.NOTE! The motor overheating (0104) may also be caused by wrong K-parameters,
problems in brake opening circuit or mechanical problems in brake.
8.5 Cold elevator shaft and installation conditions (for example car parks)
NOTE! Drive temperature fault 0110 indicates both over and under temperatures.
1. Check the temperature of the elevator shaft and inform the building owner if it is below+5C.
2. Add heating to the elevator shaft.
8.6 Temporary main supply
1. Check that residual circuit breaker is rated at least for 300 mA if any or alternatively addisolation transformer to line side.
2. Check that all three line phases are powered and stable.
8.7 EBD-A problems
1. Check the phase order of the EBD-A supply.2. Check that the +24 Volt supply is over +18 volts all the time.3. If elevator stops at the dummy floor in EBD-A mode, install new version of the LCE and
drive software. This is valid for LCE software versions older than 5.2.0 and drive softwareversions older than 0.63.Load LON-protocol (5_7_1) after LCE software update.
© 2004 KONE Corporation AM-11.65.022All rights reserved. 13 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
9 READING DETAILED FAULT CODES
The sub fault codes of the V3F16L drive are describing the faults in detail (refer to the804611, V3F16L Fault Codes). Sub fault codes are saved to the error log.
The numbering of the sub fault codes is divided to the following categories:
• 1000-serie, the elevator is locked (driving is prevented)• 2000-serie, driving of the elevator is stopped by a machine brake• 3000-serie, warnings indicated in advance (before a device or equipment break down)• 6000-serie, diagnostic information. All sub codes in this category DO NOT indicate a fault.
They are for getting additional information.
9.1 How to read the sub fault codes
This example describes how to read sub codes 118_6010 and 118_6011.
1. Enter error log.
2. Push ACCEPT (a row of figuresstarts to scroll.
1.
SELECT
ACCEPT2.
1021405.wmf
118 Shaft Setup118 2021 Setup started at wrong position
2023 Setup stopped because 77:U/Nactive at same time
6010 Reports minimum 61:U/Noverlap
floor overlap mm
© 2004 KONE Corporation AM-11.65.022All rights reserved. 14 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
10 ADDITIONAL PROCEDURES
10.1 Balancing the elevator by measuring from the MAP
Step Action Note1 Measure the voltage of the measuring
points TP1 (+) and TP2 (-) on the User interface board. This voltage is equivalent to the motor current (0.34 VDC = 1 A).
Drive empty car downwards.Drive the car (with a rated load inside) upwards. Record the values.
User interface board:
2 Compare the values. Re-balance if needed.
Values should be as equal as possible.
© 2004 KONE Corporation AM-11.65.022All rights reserved. 15 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
10.2 Load weighing device adjustment (half load in the car)
LWD should show 0% at top floor with empty car.
10.3 LEDs in the user interface board
V3F OK-LED is offCommunication failure between LCE and drive.
1. Check the possible diagnostic codes.2. If no diagnostic code occur, open the drive module cover. Check if the LED in the drive
module is blinking.3. If the LED does not blink:
• Check the parameter 1_95 (it must be set to 1).• Check the cable between drive module (XL1) and LCECPU board (X4).
4. Check the +24V-LED.
Start permit-LED is always on or off1. Check LCE side XS3/1,3 (start permit chain).
Step Action Note1 Drive the car 10-30 times from a
terminal floor to another.2 Drive the car and counterweight to
middle of the elevator shaft.3 Adjust the load weighing device
OFFSET setting to 0%.4 Place half of the rated load in the car.5 Adjust the load weighing device GAIN
setting to 50%.6 Check that the rope tensions (length of
the springs) are equal at the rope anchorages.
7 Drive the car 10-30 times from a terminal floor to another.
8 Check the LWD indication at the topmost and lowest floor with empty car and with a car loaded 100% of the rated load.
© 2004 KONE Corporation AM-11.65.022All rights reserved. 16 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
11 VERSION HISTORY AND APPROVALS
Compiled by: Technical Editor / Ville Malmiala
Checked by: Life Cycle Manager / Pasi Raassina KCO Installation Support / Riccardo Pittau KCO Installation Support / Paul Durbin KCO Installation Support / Danilo De Rossi
Approved by: KCO Installation Support / Bob Major
Issue Date Description of Change Ref CR Approved by- 2004-03-30 First issue Bob Major
© 2004 KONE Corporation AM-11.65.022All rights reserved. 17 (18) (-) 2004-03-30
V3F16L DriveTroubleshooting
© 2004 KONE Corporation AM-11.65.022All rights reserved. 18 (18) (-) 2004-03-30
This page has been added to make double sided printing easier.
V3F16L Parameter Table (short) 784393Compiled by: J. Laaksonheimo Date: Issue: E
Changed by: J. Laaksonheimo (C) KONE Corporation No of Pages: 2
Checked by: M. Karppinen Draving no: Language: en
Approved by: K. Aarnio Product code: SW: Excel 97 SR-2
The document id of this sheet must match with the id reported by LCE menu 6_0
LCE menu unit range
defaultvalue
actual value
Elevator Parameters
- document identification of the parameter set (= this sheet) 6_0 5000… 5005 - motor parameters 6_1 5.10 , …, 10.20 10,20
- nominal speed of the elevator (determines also acceleration and jerk) 6_2 m/s 0.50, …, 1.00 1,00
- elevator load 6_3 kg 200, …, 2 000 1000
- roping 6_4 2 , 4 2
User Information
- stator frequency (synchronous frequency at nominal speed) 6_10 Hz 0.0, …, 100.0 CALC
NOTE! These parameters are calculated by drive and can be read only.
Additional Elevator Parameters
- acceleration (manually changeable, determines also jerk) 6_20 m/s2 0.25, …, 0.65 CALC
- jerk (manually changeable) 6_21 m/s3 0.25, …, 1.20 CALC
- D factor ( = derivativel gain of speed controller) 6_22 s2/m 0.0, …, 15.9 3,5
- tacho filter time 6_23 ms 0, …, 50 30
- speed reduction ( = reduced speed / nom. speed) 6_24 0.30, …, 1.00 1,00
- tacho fault counter 6_25 0, …, 10 5
- start delay ( = brake open command -> speed ref.) 6_26 s 0.10, …, 0.50 0,15
- vane length ( = electrical length of 61 vanes) 6_27 mm 50, …, 500 150
- inspection speed ( = elevator speed in inspection or RDF mode) 6_28 m/s 0.3, 0.5 0.3
- final jerk distance ( = additional distance used for final jerk) 6_29 mm 0, …, 250 80
NOTE! final jerk distance (6_29) changes also distance advance (6_48).
Machinery Parameters and Variables
- default parameter lock (0 = open, 1 = locked) 6_50 0, 1 1
- tacho scaling factor 6_51 0.400, …, 0.900 0,900
- magnetizing current ratio (Imag / Inom at start) 6_52 0.500, …, 1.000 0,80
- minimum voltage (K1) 6_53 0.000, … , 0.050 CALC
- load compensation low (K2) 6_54 0.000, … , 0.300 CALC
- load compensation high (K3) 6_55 0.000, … , 0.200 CALC
- motor voltage (K4 V/f ratio) 6_56 0.000, … , 0.415 CALC
- acceleration factor (voltage control parameter) 6_57 0.40, … , 1.50 1,20
- deceleration factor (voltage control parameter) 6_58 0.00, … , 0.80 0,30
- number of pole pairs 6_59 0, … , 15 CALC
NOTE! Default values for motor paraneters are calculated when motor parameters (6_1) is changed.
Commissioning and tests
- enable traction test (1=full car, 2=empty car) 6_80 0, 1, 2 0
NOTE! Traction test is valid for one start only.
Permanent Store
- V3F software version 6_97 0.00, …, 10.00
- factory default parameters 6_98 0, 1 0
- save (saves parameters into permanent memory) 6_99 0, 1 0
NOTE! Before factory parameters can be loaded default parameter lock (6_50) must be set to zero.
Copyright (C) 2002 KONE Corporation. All rights reserved.
5.12.2002
784393
V3F16L
NOTE! Before motor parameters can be changed number of pole pairs (6_59) must be set to 0.
V3F16L Parameter Table (short) 784393
Motor parameters5,10 MX055,20 MX05/105,21 MX05/10 MICROSPACE6,10 MX06; MX06A EU; MX06A EA6,20 MX06/10; MX06/10 EA; MX06/0510,10 MX10; MX10A EU; MX10A RU; MX10A EA10,20 MX10/10; MX10/10 RU; MX10/10 EA; MX10/05
Copyright (C) 2002 KONE Corporation. All rights reserved.
V3F1
6L F
ault
Cod
esPa
ge: 1
of 2
DR
AWIN
G N
O:
V3F1
6L D
rive
FAU
LT C
OD
ES80
4611
CO
MPI
LED
BY:
ISSU
E:
HA
T/R
isto
Jok
inen
(Pet
teri
Kan
gas,
Pek
ka V
uoti)
V3F1
6LA
26.
3.20
03C
HAN
GED
BY:
CH
ECKE
D B
Y:LA
NG
UAG
E:
HA
T/R
isto
Jok
inen
HA
T/M
arko
Kar
ppin
enen
DAT
E
APPR
OVE
D B
Y:SW
:EC
C/K
imm
o A
arni
oM
S EX
CEL
7.0
Faul
t co
de
subc
ode
Des
crip
tion
Dat
a 1
Dat
a 2
Rea
son
Det
ectio
nO
pera
tion
Rec
over
yTe
stin
g10
2 D
rive
Ove
rcur
rent
102
2001
Peak
val
ue o
ver l
imit
Ove
rcur
rent
By h
wSt
ops
imm
edia
tely
--
102
2002
Ove
r cur
rent
Shor
t circ
uit i
n m
otor
term
inal
sBy
hw
Stop
s im
med
iate
ly-
-10
3 R
esis
tor b
raki
ng/re
gene
ratio
n fa
ult
103
1002
Brak
ing
resi
stor
bro
ken
Prob
lem
in b
raki
ng re
sist
or
wiri
ng/c
onne
ctor
, bra
king
resi
stor
br
oken
or b
raki
ng tr
ansi
stor
br
oken
By h
wSt
ops
imm
edia
tely
-D
isco
nnec
t bra
king
re
sist
or c
onne
ctor
104
Mot
or P
rote
ctio
n10
420
03M
otor
ther
mis
tor
Mot
or o
verh
eat o
r mot
or
ther
mis
tor c
able
dis
conn
ecte
dO
n/O
FF p
tcD
rive
will
not s
tart
Afte
r ~5m
ins
whe
n m
otor
tem
pera
ture
is
low
er
By lo
wer
ing
limits
or
by re
plac
ing
mot
or
ptc
with
po
tent
iom
eter
105
Pow
er s
uppl
y fa
ult
105
2006
DC
link
sup
ervi
sion
To
o lo
w m
ain
volta
ge, t
oo h
igh
mai
n vo
ltage
, or r
unni
ng a
t 2
phas
e.
By c
ompa
rato
r on
Inve
rter b
oard
driv
e ca
n no
t sta
rt, o
r m
akes
qui
ck s
top
in
mov
ing
stat
e
Whe
n po
wer
is o
k,
3 se
c re
cove
ry
time
Adju
stab
le s
uppl
y
106
Driv
e st
andb
y er
ror
10
610
01TF
C (T
acho
faul
t cou
nter
)To
o m
any
Torq
ue/s
peed
co
ntro
ller e
rrors
in ro
wTh
is m
onito
rs D
iffer
er
rors
Lock
s el
evat
or w
hen
over
lim
itBy
RD
F/In
spec
tion
mod
e
Rem
ove
velo
city
fe
edba
ck
107
Load
wei
ghin
g er
ror
107
2008
Lwd
out o
f ran
geN
ot a
djus
ted
or m
issi
ngBy
com
parin
g m
easu
red
valu
e to
the
limits
Inhi
bits
nex
t sta
rtW
hen
lwd
wor
ks
corre
ctly
Dis
conn
ect l
wd
108
Torq
ue/S
peed
con
trol
ler e
rror
108
2009
Diff
eren
ce b
etw
een
spee
d re
fere
nce
and
mea
sure
d sp
eed
exce
eded
Diff
eren
ce b
etw
een
spee
d re
fere
nce
and
mea
sure
d sp
eed
is
too
high
By c
ompa
ring
mea
sure
d va
lue
to th
e re
fere
nce
Stop
s im
med
iate
lyaf
ter f
ew s
econ
ds,
incr
emen
ts ta
cho
faul
t cou
nter
rem
ove/
dist
urb
spee
d m
easu
rem
ent
3001
Diff
eren
ce 9
0% o
f pre
viou
s lim
itD
iffer
ence
bet
wee
n sp
eed
refe
renc
e an
d m
easu
red
spee
d is
ve
ry n
ear l
imit
By c
ompa
ring
mea
sure
d va
lue
to th
e re
fere
nce
Alar
m s
how
n af
ter r
un-
-
2010
Mot
or to
rque
lim
it ex
ceed
edN
eede
d to
rque
ove
r exp
ecte
dBy
torq
ue/s
peed
co
ntro
ller
Stop
s im
med
iate
lyaf
ter f
ew s
econ
ds,
incr
emen
ts ta
cho
faul
t cou
nter
-
3002
90%
of m
otor
torq
ue u
sed
Nee
ded
torq
ue v
ery
near
of
expe
cted
-Al
arm
sho
wn
afte
r run
--
2011
Stal
ling
prot
ectio
nM
otor
doe
s no
t rot
ate
By c
ompa
ring
mea
sure
d va
lue
to th
e re
fere
nce
Stop
s im
med
iate
lyaf
ter f
ew s
econ
ds,
incr
emen
ts ta
cho
faul
t cou
nter
Dis
conn
ect b
rake
, an
d ca
use
accu
rate
le
vellin
g
This
doc
umen
t is
auto
mat
ical
ly g
ener
ated
from
doc
umen
t #8
0461
2! D
o no
t man
ually
mod
ify
14.1
.200
3
KO
NE
KO
NE
Cop
yrig
ht ©
199
9 Ko
ne C
orpo
ratio
n. A
ll rig
hts
rese
rved
.
V3F1
6L F
ault
Cod
esPa
ge: 2
of 2
Faul
t co
de
subc
ode
Des
crip
tion
Dat
a 1
Dat
a 2
Rea
son
Det
ectio
nO
pera
tion
Rec
over
yTe
stin
g10
9 Po
sitio
ning
err
or
10
930
05Po
sitio
n lo
stTo
o bi
g po
sitio
n up
date
of
posi
tion
is n
ot in
syn
c w
ith s
haft
sign
als
By c
ompa
ring
shaf
t im
age
to th
e in
put
sign
als
Slow
dow
nAf
ter p
ositi
on is
fo
und
agai
nC
ause
big
pos
ition
up
date
1012
77:U
/N a
ctiv
e at
sam
e tim
eBo
th 7
7:U
/N a
ctiv
e at
sam
e tim
e-
Lock
s el
evat
orIn
spec
tion
mod
e or
faul
t dis
appe
rsSe
t bot
h on
at s
ame
time
110
Driv
e Te
mpe
ratu
re11
020
14H
eats
ink
tem
pera
ture
is to
o hi
gh
or lo
wAm
bien
t tem
pera
ture
too
high
or
low
. Air
flow
blo
cked
. Hig
h ED
va
lue.
Hea
tsin
k te
mpe
ratu
re is
m
onito
red
Prev
ents
sta
rtAf
ter f
ew m
inut
es
(5..1
0min
), or
w
hen
ambi
ent
tem
pera
ture
is in
op
erat
ing
limits
Hea
t sen
sor w
ith
blow
er, o
r coo
l it w
ell
belo
w 0
deg
rees
C
elci
us
118
Shaf
t Set
up
11
820
21Se
tup
star
ted
at w
rong
pos
ition
C
ar is
not
wel
l bel
ow 6
1:N
edg
e be
fore
sta
rt61
:N is
on
whe
n en
terin
g to
the
spee
d re
fere
nce
phas
e 1
Stop
s im
med
iate
lyR
etry
set
upSt
art s
etup
ver
y ne
ar
of 6
1:n
edge
2023
Setu
p st
oppe
d be
caus
e 77
:U/N
ac
tive
at s
ame
time
77
:U/N
Seq
uenc
e is
not
cor
rect
77:U
/N/S
seq
uenc
e is
ve
rifie
dSt
ops
imm
edia
tely
Che
ck s
haft
switc
hes
in
insp
ectio
n m
ode
and
retry
set
up
Cau
se w
rong
77:
U/N
si
gnal
dur
ing
setu
p (s
imul
ator
)
6010
Rep
orts
min
imum
61:
U/N
ov
erla
p flo
orov
erla
p m
mD
iagn
ostic
info
rmat
ion
to a
void
to
o sm
all o
verla
pO
verla
p is
mea
sure
d du
ring
setu
p ru
nVa
lue
is s
how
n af
ter
setu
pN
ot n
eede
dC
ause
ver
y sh
ort
and
very
long
ov
erla
ps60
11R
epor
ts m
axim
um 6
1:U
/N
over
lap
floor
over
lap
mm
Dia
gnos
tic in
form
atio
n to
avo
id
too
high
ove
rlaps
Ove
rlap
is m
easu
red
durin
g se
tup
run
Valu
e is
sho
wn
afte
rse
tup
Not
nee
ded
Cau
se v
ery
shor
t an
d ve
ry lo
ng
over
laps
120
Star
t seq
uenc
e er
ror
120
1R
ollb
ack
war
ning
(Hid
den
with
LC
E 5.
1.x
or n
ewer
)N
ext s
tart
is S
peci
al s
tart
Prev
ious
sto
p w
as
abno
rmal
.M
otor
is s
tarte
d w
ith v
ery
high
sta
rt to
rque
, rol
lbac
k is
pos
sibl
e
At n
orm
al s
top
Cau
se q
uick
sto
p.
Nex
t sta
rt is
'spe
cial
st
art'
2025
No
Mot
or C
urre
ntC
ould
occ
ur w
hen
star
t is
abor
ted
at v
ery
late
pha
se, o
r mot
or
cont
acto
r is
not e
nerg
ized
or
mot
or c
able
is n
ot c
onne
cted
Ther
e is
no
mot
or c
urre
nt
at th
e m
omen
t whe
n br
ake
open
sho
uld
star
t
Stop
s im
med
iate
lyAt
nex
t sta
rtD
isco
nnec
t mot
or
cabl
e or
kee
p m
otor
co
ntac
tor o
pen
2026
Tach
o si
gnal
act
ive
at w
rong
tim
eTa
chom
eter
has
ver
y hi
gh n
oise
le
vel o
r lift
mov
es to
o ea
rly a
t st
art
spee
d is
ove
r 2cm
/sec
w
hile
bra
ke c
ontro
l is
still
inac
tive
Stop
s im
med
iate
lyAt
nex
t sta
rtO
pen
brak
e ju
st a
t st
art o
r kee
p br
ake
rela
y cl
osed
Cop
yrig
ht ©
199
9 Ko
ne C
orpo
ratio
n. A
ll rig
hts
rese
rved
.