TETRACUBE PANEL X-POL ANTENNACONFIGURATION 2X1
375 ÷ 400 MHzPOLOMARCONI offers a very wide range of wireless products.Our products can be tailored according to the customer’s need.
Made in Italy. We reserve the right to modify these data without any notice.BY
17400021
PMR
1 / 2
17400021-DS REV. 07 - 03/06/2015
Electrical Specif ications
Frequency band (MHz) 375 ÷ 400
Bandwidth (MHz) 25
Input impedance (Ω) 50
VSWR (of the entire 2x1 array system) ≤ 1.5:1
Continuous Max. Power (W) 500
Isolation between channels (dB) (of the entire 2x1 array system) > 30
Polarization (deg) ±45°
Gain (dBi) (of the entire 2x1 array system) 2 x 9.2
HPBW (°) - H-plane (of the entire 2x1 array system) 109
HPBW (°) - E-plane (of the entire 2x1 array system) 37
Front-to-Back ratio (dB) > 27
Electrical Down Tilt (deg) 0°
Intermodulation 3rd/5th order (dBc) @ 2x43 dBm <-150 / <-160
Operation Temp. Range (°C) -40° ÷ +70°
Mechanical Specif ications
Connectors 4x7/16 f
Dimensions (Height x Width x Depth, mm) 835x520x430
Weight antenna structure (kg) 8
Wind load (N) @ 200 km/h Frontal / Lateral / Rearside418 / 260 / 444
Radiation Patterns(of the entire 2x1 array system)
DESCRIPTION:
TETRACUBE panel X-pol antenna.
The design of TETRACUBE antenna is based on fundamental engineering knowledge and also on practical experience, during which the various constructions and materials used have proved their outstanding reliability. Designed to operate on the environmental conditions as described in ETSI 300 019-2-4.
The radome that covers the internal components is made of Polycarbonate material that guarantees optimum performances with regards to stability (tested in accordance to DIN EN ISO 4892-2), stiffness, UV resistance and best weather protection.In case of very light colours, it is possible to apply a further transparent varnish 2K scratch resistant, to further increase the UV protection and further delaying the yellowing of the material.
Four inputs, wide HPBW angle and high Front-to-Back ratio.
Reduced dimensions and light weight.
DC grounded from lightning protections.
STEP 1: Take the radial, pre-installed on its appropriate support
STEP 2: Take the two M6 screws and the proper Allen key contained within the antenna mounting kit
STEP 3: Take the thread locker contained within the antenna mounting kit
STEP 4: Deposit a sufficient amount of thread locker on the threads of the two M6 screws provided in the antenna mounting kit
STEP 5: Place the radial support in its suitable position at the center of the mechanical support structure of the 2x1 array antenna, in correspondence of the two proper fixing holes. Tighten the two M6 screws provided in the antenna mounting kit, with the proper provided Allen key, in both their appropriate locations.
STEP 6: Final TetraCube 2x1 array antenna structure 17400021
pre-installed radial
support
provided M6 screws and Allen key
M6 screws proper
locations
center of the mechanical
support structure of the
2x1 array antenna
TETRACUBE PANEL X-POL ANTENNACONFIGURATION 2X1
375 ÷ 400 MHzPOLOMARCONI offers a very wide range of wireless products.Our products can be tailored according to the customer’s need.
Made in Italy. We reserve the right to modify these data without any notice.BY
17400021
PMR
2 / 2
17400021-DS REV. 07 - 03/06/2015