Download - Avioneta para imprimir
-
8/10/2019 Avioneta para imprimir
1/12
Spirit of St. Louis : Assembly Instructions
PAGE01
The Spirit of St. Louis (also known as the Ryan NYP-1) is a single-engine plane that was successfully
flown by Charles Lindbergh as a solo non-stop transatlantic flight. The main external features of the
craft were its lack of front windshield, and its wings, which were extremely long compared to its body.The aircraft took off from New York's Long Island and flew 5,810km to Paris. The journey took 33
hours, 29 minutes and 29.8 seconds, which was regarded as quite fast at the time. It was the first solo,
non-stop flight to travel this route.
This papercraft Spirit of St. Louis is about one twenty eighth the size of the real Spirit of St. Louis.
*This model was designed for Papercraft and may differ from the original in some respects.
Glue tab notation key
Glue
Each glue tab has a symbol andnumber printed on it.
Glue with in the same part.
(Dotted line)Mountain fold
Guide rod
How to make the cylinders
This craft involves making cylinders
with diameters of 3 to 7mm, so it may
be helpful to have some rods of sizes
about 0.5mm thinner handy.
Assembly Instructions
Wrap around and glueto the top of the cylinder.
(Dashed and dotted line)Valley fold
(Solid line)Scissors line
You may like to use
a metal rod as a guide.
Layer wrapping (roll)Wrap around and glue to thecylinder,to use as a glue tab
(Red solid line)Cut in Line
Completed partsbecome a cylinder
Trace along the folds with a ruler anda used pen (no ink) t o get a sharper,easier fold.
Glue, scissors and other tools may be dangerous toyoung children so be sure to keep them out of thereach of young children.
Parts list (Assembly Instructions) : Twelve A4 sheets
No. of Parts: 177
*Bulid the model by carefully reading theAssembly Instructions,
in the parts sheet page order.
Spirit of St. Louis
-
8/10/2019 Avioneta para imprimir
2/12
PAGE02 Scissors line Mountain fold Valley fold Cut outCut in Line
Spirit of St. Louis : Assembly Instructions
2-B2-C2-D
2-F
2-E 2-A
2-J
2-M
2-W
2-X
2-W
2-X-1
2-X-1
2-P-1
2-W
2-Y
2-Y-1
2-I
2-I
2-Z-1
2-Z-2
2-P-2
2-P-2
2-Z
2-C/2-D
2-F/2-E
2-A/2-B
-
8/10/2019 Avioneta para imprimir
3/12
PAGE03
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line
2-T
2-P
2-R
2-Q
2-Q/R
2-P
2-S
2-Q-1
3-C
3-B
2-K
2-L 2-L-1
2-K/2-K-12-L/2-L-1
Insert in between 2-W
and 2-J/M and attach.
Insert the long glue tabs
on 2-S through the holes
in 2-Q/R and fasten them
to the glue tabs on 2-P.
2-P-1
3-D
3-E-1/3-A-1
2-S
3-D
3-E/3-E-1
Insert the protruding parts of 3-B
into the holes on 3-A/3-A-1/3-E/3-E-1,
fold them and attach them to the
protruding parts of 3-D.
Do not put glue on 3-A/3-A-1/3-E/3-E-1.
3-E/3-A
3-S-1/3-S
After attaching
the tail assembly,
attach it to 2-P-1.
After gluing, check that the parts move.
2-K-1
2-P/Q is moveable.
-
8/10/2019 Avioneta para imprimir
4/12
PAGE04
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line
3-G
2-O
3-F
2-U
2-N
2-H
4-E
4-E-1
3-H
4-D-1
4-D
4-C-1
4-C
2-G
Attach 2-O in linewith the fold lines
on 3-F and 3-G.
-
8/10/2019 Avioneta para imprimir
5/12
PAGE05
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line
Cross-sectional diagram of how to glue the engine parts
With the bumpy ends omitted Push in towardsthe center.
Glue thecenter joiningparts together.
Bendtowardsthe back.
Push in towardsthe center.
3-L
3-I
3-I 3-I
3-Q
3-R
3-P
3-O
3-N
4-Q
4-K
4-O
4-O/4-P
4-L
4-O
4-P
Align these parts on 4-P/4-O.
4-P
4-R
3-M
-
8/10/2019 Avioneta para imprimir
6/12
PAGE06
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line
Cross-sectional diagram of how to assemble t he propellor shaft
Only put glue on 4-M. In step , before attaching
4-H to 4-K, check that the 4-K parts rotate.
4-J
4-M
4-M
4-H
4-H
4-Z
4-Z
4-H
4-N
4-N
4-O/P4-N
4-K
4-H
4-U
4-W
4-U/4-W
3-K
4-U/4-W
4-H
4-Z
3-Q/R
4-M
4-M
4-J
4-R
4-J
4-K4-J
Cut a slot.Add a curve tothe 4-Z glue tabs.
Glue the 4-Z glue tab partsto the inside of 4-H.
*Do not glue 4-J.
*Do not glue 4-J/4-K.
*Glue 4-H to 4-K.
*Add a curve to 4-U/4-W after gluing.
*Curve it as shown.
*Insert 4-U/4-W into the slots
on 4-H and attach.
-
8/10/2019 Avioneta para imprimir
7/12
PAGE07
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line
5-C/6-C
5-C/6-C
5-B/6-B
5-I/6-G
5-H/6-F
5-A/6-A
5-F
5-F
5-F/5G
5-G
5-G
5-E/6-E
5-D/6-D
*Make 10 pairs altogetherof 5-D/6-D/5-E/6-E.
Make two pairs.
Where to attach 5-F/5-G.
-
8/10/2019 Avioneta para imprimir
8/12
PAGE08
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line
5-I/6-G
5-H/6-F
Side view after gluing
Start gluing from the folded side and work back.
5-A/6-A
5-A/6-A
5-D/6-D
5-D/6-D
5-A/6-A
5-B/6-B
5-B/6-B is moveable
so do not put glue on
the wing.
5-A
6-A*Attach the tip ofthe wing together first.
*Insert 5-B/6-B into the wing. (Do not add glue.)
*The 5-A/6-A wing is assembled in the same way.
Place 5-A/6-A on the template on page 7 of the parts sheet as shown in the figure below and attach them in line with the black lines.
Plane side of wing
Fold in without gluing.
Moves up and down.
Moves up and down.
Papertemplatetoattachtothewing5-D/6-D.
Align the tips of 5-D/6-D with thefold line of the glue spot on5-A/6-A, and begin to attach.
Attach 5-D/6-D at a position so thatthe glue spot is folded 45 .
*After completing steps and ,attach the wing together.
-
8/10/2019 Avioneta para imprimir
9/12
PAGE09
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line
3-U/3-U-1
3-U/
3-U-1
6-I/6-H
6-I/6-H
6-H
3-J/3-Y
3-J/3-Y
4-I
4-I
4-A/4-B
3-X/3-X-1
3-X/3-X-1
4-S/4-T
7-K
4-S/4-T
3-W/3-W-1
3-W/3-W-1
4-A/4-B
3-T-1 3-T-1
7-K
5-A/6-A
3-L
6-I
Wings
Align the tip of 3-L with the wings,fold the edge forward and attach.
Wrap around
4-A/4-B andattach.
3-U-1
3-U
3-Y
4-A
3-J
4-B
-
8/10/2019 Avioneta para imprimir
10/12
PAGE10
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line
4-G
4-F
4-F
4-F4-F
3-T 3-Z
3-T
7-E7-E
7-E
Glue spot
7-E
4-G
4-G
4-G
Slot 7-E onto 4-A/4-B,and attach to the body.
Slot 7-E onto 7-C/7-D,and attach to the body.
Wrap 3-T/3-Z around3-U and attach.
7-A
7-B
7-B
7-C
7-D
7-D
Body
Attach to the body.
Put glue on 4-G/4-Fand attach.
-
8/10/2019 Avioneta para imprimir
11/12
-
8/10/2019 Avioneta para imprimir
12/12
PAGE12
Spirit of St. Louis : Assembly Instructions
Scissors line Mountain fold Valley fold Cut outCut in Line