Download - Basic Operation Training of romes
-
ROHDE & SCHWARZROMESBasic OperationTraining
-
Introduction
-
Romes Basic Operation Training15TMO-Q273_Aug13
3. Load workspace file (*.rsxks) (Step 3.5)(Follow step 3.1 3.4 if workspace has not been created)
Step 7: Exit ROMES &Open Measurement File
Step 4: Start measurement
Step 6: Stop measurement
2 .Start ROMES
Step 5: Drive Test
1. Connect Devices
Measurement Work Flow
-
Step 1: Connect Device
-
Romes Basic Operation Training15TMO-Q273_Aug13
LAN Cable
Power
Antenna
GPSAntenna
TSMW
Dongle
Making Connection
-
Romes Basic Operation Training15TMO-Q273_Aug13
Configure IP Address (Laptop)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l The IP address of the TSMW is by default set to 192.168.0.2
Configure IP Address (Laptop)
-
Romes Basic Operation Training15TMO-Q273_Aug13
Remember to turn-off firewall
Only need to do this step if new firmware is released
Firmware/Options Installation
-
Step 2: Start Romes
-
Romes Basic Operation Training15TMO-Q273_Aug13
With Dongle (for measurement)
Without Dongle (for replay, export, post process)
Start ROMES
-
Step 3: Create/Load WorkSpace
-
Romes Basic Operation Training15TMO-Q273_Aug13
Createworkspace
Step 3.1: Load SW Drivers
Step 3.2: Configure SW Driver
Step 3.3: Load Map
Step 3.4: Save Workspace
l A workspace contains all measurement settingsl It only needs to be created once and can be recalled on following
measurements
Creating Workspace
-
Step3.1: Load SW Drivers
-
Romes Basic Operation Training15TMO-Q273_Aug13
l Add/Remove Hardware Loading of respective technologies drivers.
l Available Drivers Dependent on options purchased by Customer.
Software Drivers(Loading)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l Resource Allocation Allocate resources on various Front End. Wrong Allocation prevent user from connection. Clicking on Distribution allows auto allocation by system.
Software Drivers(Loading)
-
Step 3.2: Configure Loaded Drivers
-
Romes Basic Operation Training15TMO-Q273_Aug13
l Loaded Drivers Right Window shows successful loaded drivers.
Software Drivers(Loading)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l Configuration of loaded Drivers Configure respective loaded drivers.
l Sub Title2 Content
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l CDMA Driver Name of carriers Frequency/channel/band etc to decode
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l CDMA Driver Saving/Loading of configured driver as Template.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l UMTS PN Driver Name of carriers Frequency/channel/band etc to decode
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l UMTS PN Driver Saving/Loading of configured driver as Template.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l Wimax Driver Name of carriers Frequency/Bandwidth etc to decode
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l Wimax Driver Saving/Loading of configured driver as Template.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l GSM Driver Specify the GSM network, channels etc to decode. Saving/Loading of Template.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l BTSPE Driver Enable required technologies for BTSPE. Dependent on options purchased by customer.(Note: Wimax BTSPE is not supported)
Optimization at click of button.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l BTSPE Driverl Min. position error (estimation cutoff) Defines a distance in meter which limits the position
estimation to a reasonable accuracy for performance reasons. If 66% probability of the estimated position falls below this
distance, the estimation process for this transmitter is finished.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l BTSPE Driverl Update rate of results Defines the period in seconds between estimation orders for
the position estimator. After executing the estimation order,new position estimation results will be requested from theposition estimator and will be stored in the measurement file(*.rscmd).
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l BTSPE Driverl Tower Merger Mode Assume several transmitters are located on the same tower
(geographic position). The estimation algorithm can improve estimation accuracy
significantly.
The tower merging supports the followingmodes: OFF: which prevents merging the position of towers Aggressive: which may improve the amount ofmerged signals on the cost of a higher probability ofwrong assumptions Moderate: which ensures that no signals are mergedby mistake at the cost of less merged signals.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l BTSPE Driverl Position estimation knowledge base file Use/dont use a knowledge base file to enhance later measurements.l Discard all measurements older than xxx hours when storing the
knowledge base For performance reasons and data volume limiting: The option to
discard older measurements (than hours) from the knowledgebase when storing the file.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l RF PowerScan Driver Creation of multiple windows for RF powerscan.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l RF PowerScan Driverl Basic Settings Specify Sweep Name, Frequency etc.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l RF PowerScan Driverl Measurement Settings Specify Bandwidth/FTT etc.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l RF PowerScan Driverl Detector Settings Specify Count of Lines/RMS/Max etc.
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l RF PowerScan Driverl Channel Filter Enable filtering on specify signal in RF power scan
Software Drivers(Configuration)
-
Romes Basic Operation Training15TMO-Q273_Aug13
l RF PowerScan Driverl Example setting.
Software Drivers(Configuration)
-
Step 3.3: Load Map
-
Romes Basic Operation Training15TMO-Q273_Aug13
Load MapInfor Mapl MapInfor Map
Right Click on the Navigation View Click on Map -> Load MapInfo Map -> Load Map User need to provide own license map
-
Romes Basic Operation Training15TMO-Q273_Aug13
Load OpenStreet Mapl Open StreetMap
Right Click on the Navigation View. Click on Map -> Load OpenStreetMap. Required Internet Connection. Required licensed dongle and GPS signal if loading map during
outdoor measurement.
-
Romes Basic Operation Training15TMO-Q273_Aug13
Loading Parameters on Mapl Configure Map
Right Click on the Navigation View> Configure Choose the parameter of interest to be displayed on the map. During Measurement no additional parameters can be defined. New parameters can be display on map in replay file.
-
Step 3.4 Save Workspace
-
Romes Basic Operation Training15TMO-Q273_Aug13
Saved WorkSpacel Workspace
Saving of work space after all configuration is done.
-
Step 3.5 Load Workspace
-
Romes Basic Operation Training15TMO-Q273_Aug13
Load Workspacel Workspace
Open work space from previous setting.
-
Step 4: Start Measurement
-
Romes Basic Operation Training15TMO-Q273_Aug13
Start Measurement
-
Step 5: Start Drive Test
-
Romes Basic Operation Training15TMO-Q273_Aug13
Start Drive Test
-
Step 6: Stop Measurement
-
Romes Basic Operation Training15TMO-Q273_Aug13
Stop Measurement
-
Step 7: Open Measurement File
-
Romes Basic Operation Training15TMO-Q273_Aug13
Replay Measurement File
-
Romes Basic Operation Training15TMO-Q273_Aug13
Replay Measurement File
-
8.0: Others Information
-
8.1: Indoor Measurement
-
Romes Basic Operation Training15TMO-Q273_Aug13
l Navigation View Maps
Load Indoor Map
-
Romes Basic Operation Training15TMO-Q273_Aug13
Load Indoor Mapl Navigation View
Maps
-
Romes Basic Operation Training15TMO-Q273_Aug13
Load Indoor Mapl Navigation View
Maps
Reference: http://wise.cnit.it/files/user79/indoor-map.png
-
Romes Basic Operation Training15TMO-Q273_Aug13
Configure Software Driverl Indoor DriverRepeat Step 2 by loading respective technologies driver. For navigation driver,change to indoor input.
Hot Spot Continuous
-
Romes Basic Operation Training15TMO-Q273_Aug13
Configure Software Driverl Indoor Driver
Hot Spot
-
Romes Basic Operation Training15TMO-Q273_Aug13
Configure Software Driverl Indoor Driver
Continuous
-
Romes Basic Operation Training15TMO-Q273_Aug13
Configure Software Driverl Route Track View
Enable/Disable PreviousRoute information in new measurement.
-
8.2: Network Provider Database
-
Romes Basic Operation Training15TMO-Q273_Aug13
Network Provider Databasel Updating of Network Provider Database
Tools> Network Provider Database
OperatorLogo
Operator Name
Operator Country
-
Romes Basic Operation Training15TMO-Q273_Aug13
Network Provider Databasel Updating of Network Provider Database
Updating/Adding of operators information/ icon/ Band etc.
OperatorLogo
Operator Name
Operator Country
To define theOperators and itssupportedtechnology, band andchannels
To provide theoperators logo. Thelogo need to be in.ico format.
Browse to country of interest toupdate operator information.
-
Romes Basic Operation Training15TMO-Q273_Aug13
l These training slides provide basic ROMES operation instruction forrecording. For more detail setting, please refer to ROMES Manual.
Note
-
Romes Basic Operation Training15TMO-Q273_Aug13
l Sub Title1 Content
l Sub Title2 Content
Title
-
Romes Basic Operation Training15TMO-Q273_Aug13
THE END