Download - Body Side Moulding Instructions
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2007 American Honda Motor Co., Inc. – All Rights Re
AII 37098
BODY SIDE MOLDING P/N 08P05-TA0-100served. AII 37098 (0708
2008 ACCORD 4-DOOR
) 0
Issue Date
AUG 2007
PARTS LIST
Left front body side molding
Right front body side molding
Left rear body side molding
Right rear body side molding
Front template
Rear template
4 Alcohol swabs
TOOLS AND SUPPLIES REQUIRED
Shop towel
Masking tape
INSTALLATION
• Be careful not to damage the body paint finish.
• The body side molding kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours.
• These instructions are for the left side of the vehicle. The same procedure applies to the right side of the vehicle.
• If you’re also installing door edge guards (sold separately), install them before you install the body side moldings.
1 of 38P05-TA0-1000-91
1. Position the front template in the position shown by aligning it with the end of the left front door edges and the character line of the left front door. Secure the template with masking tape as shown.
2. Position the rear template in the position shown by aligning it with the end of the left rear door edge. Secure the rear template with masking tape as shown.
712601BE
MASKING TAPE
FRONT TEMPLATE
FRONT TEMPLATE(Align with the end of the left front door edge.)
CHARACTER LINE OF THE LEFT FRONT DOOR
LEFT FRONT DOOR
LEFT FRONT DOOR EDGE
LEFT FRONT DOOR EDGE
FRONT TEMPLATE
712604CE
REAR TEMPLATE
REAR TEMPLATE(Align with the end of the left rear door edge.)
LEFT REAR DOOR EDGE
MASKING TAPE
LEFT REAR DOOR
REAR TEMPLATE
2 of 3 AII 37098
3. Clean the surface where the left body side moldings will be attached using the alcohol swab. Allow the alcohol to dry completely.
4. Peel back approximately 1½ to 2 inches of adhesive backing from each adhesive tape, and tape the ends to the front surface of the body side molding. Remove the small end pieces of adhesive backing.
7126020E
MASKING TAPE
ADHESIVE BACKING(Remove.)
2 ADHESIVE BACKINGS(Peel back 1½ to 2 inches and tape it to the front surface of the body side molding.)
LEFT FRONT BODY SIDE MOLDING
ADHESIVE BACKING(Remove.)
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
5. Align the end of the left front body side molding with the front template as shown and temporarily attach it along the top edge of the front template. If the vehicle has the door edge guards installed, align the end with the door edge guards.
6. Press on the side molding firmly with the palm of your hand while removing the adhesive backings. Remove about 2 to 4 inches at a time while pressing on the molding with the palm of your hand.
712603BE
FRONT TEMPLATE
2 ADHESIVE BACKINGS
Align the end of the door edge guard.
LEFT FRONT BODY SIDE MOLDING FRONT
TEMPLATE
LEFT FRONT BODY SIDE MOLDING
DOOR EDGE GUARD
With Door Edge Guards
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 37098
7. Peel back approximately 1-1/2 to 2 inches of the adhesive backing from each adhesive tape, and tape the ends to the outside surface of the molding. Remove the other adhesive backings.
8. Align the end of the left rear body side molding with the rear template as shown and temporarily attach it along the top edge of the rear template.
9. Press on the molding firmly with the palm of your hand while removing the adhesive backings. Remove about 2 to 4 inches at a time pressing on the molding with the palm of your hand.
10. Remove the templates.
11. Turn the templates over and repeat steps 1 through 10 to install the body side molding on the right side of the vehicle.
7126050E
2 ADHESIVE BACKINGS(Peel back 1½ to 2 inches and tape it to rear surface of the body side molding.)
ADHESIVE BACKING (Remove.)
2 ADHESIVE BACKINGS(Remove.)
LEFT REAR BODY SIDE MOLDING
MASKING TAPE
712606AE
LEFT REAR BODY SIDE MOLDING
ALIGNMENT POSITION
2 ADHESIVE BACKINGS
REAR TEMPLATE
REAR TEMPLATE
LEFT REAR BODY SIDE MOLDING
(0708) 3 of 3