TESTNCAL LABORATORYhas been assessed and accredited in accordance with the standard
ISO/IEC 17025:2017''General Requirements for the Competence of Testing &
Calibration Laboratories''for its facilities at
PLOT NO-113, POCKET-A2, SECTOR-17,DWARKA, NEW DELHI, DELHI, INDIA
in the field of
CALIBRATIONCertificate Number: CC-2055
Issue Date: 12/04/2019 Valid Until: 11/04/2021
This certificate remains valid for the Scope of Accreditation as specified in the annexure subject to continuedsatisfactory compliance to the above standard & the relevant requirements of NABL.
(To see the scope of accreditation of this laboratory, you may also visit NABL website www.nabl-india.org)
Signed for and on behalf of NABL
N. VenkateswaranChief Executive Officer
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
Permanent Facility
1 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 1 A to 10 A 0.065% to 0.055% Using 61/2 Digit DMMby Direct/ ComparisonMethod
2 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 1 mA to 400 mA 0.16% to 0.77% Using 61/2 Digit DMMby Direct/ ComparisonMethod
3 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 10 µA to 100 µA 1.0% to 0.63% Using 61/2 Digit DMMby Direct/ ComparisonMethod
4 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 100 µA to 1mA 0.093% to 0.09% Using 61/2 Digit DMMby Direct/ ComparisonMethod
5 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 400 mA to 1 A 0.77% to 0.065% Using 61/2 Digit DMMby Direct/ ComparisonMethod
6 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Resistance 1 ohm to 100 kohm 1.04% to 1.01% Using LCR-Q Meter byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 1 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
7 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage @ 50Hz 1 mV to 100 mV 0.17% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
8 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage @ 50Hz 1 V to 100 V 0.1% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
9 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage @ 50Hz 100 mV to 1 V 0.1% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
10 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage@ 50Hz 100 V to 1000 V 0.1% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
11 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Capacitance 1µF to 100µF 4.13% to 2.01% Using LCR-Q Meter byDirect Method
12 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Inductance 1 mH to 10 H 2.16% to 0.68% Using LCR-Q Meter byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 2 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
13 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC High Current @50Hz
100 A to 900 A 3.55% Using Zeal MultiFunction Calibrator,51/2 Digit with CurrentCoil by Direct Method
14 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
DC High Current 100 A to 900 A 2.35% to 1.74% Using Zeal MultiFunction Calibrator,51/2 Digit with CurrentCoil by Direct Method
15 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Resistance (2-Wire) 200 M Ohm to 200 GOhm
1.42% to 5.15% Using High ResistanceBox, by Direct Method
16 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Resistance (4-Wire) 0.001 Ohm to 10 Ohm 2.4% Using Low ResistanceBox, by Direct Method
17 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 1 A to 10 A 0.55% to 0.26% Using 61/2 Digit DMMby Direct/ ComparisonMethod
18 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 1 mA to 400 mA 0.21% to 0.07% Using 61/2 Digit DMMby Direct/ ComparisonMethod
19 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 10µA to 100µA 1.21% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
20 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 100µA to 1mA 0.1% to 0.21% Using 61/2 Digit DMMby Direct/ ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 3 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
21 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 400 mA to 1 A 0.07% to 0.055% Using 61/2 Digit DMMby Direct/ ComparisonMethod
22 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Voltage 1 mV to 100 mV 0.40% to 0.40% Using 61/2 Digit DMMby Direct/ ComparisonMethod
23 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Voltage 100 mV to 1000 V 0.21% Using 61/2 Digit DMMby Direct/ ComparisonMethod
24 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance 0.001 Ohm to 1 Ohm 1.86% to 1.12% Using 61/2 Digit DMMby Direct/ ComparisonMethod
25 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance 1 ohm to 100 ohm 1.12% to 0.41% Using 61/2 Digit DMMby Direct/ ComparisonMethod
26 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance (2 wire) 1 MOhm to 100 MOhm 0.31% to 0.095% Using 61/2 Digit DMMby Direct/ ComparisonMethod
27 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance (2 wire) 100 ohm to 1 Mohm 0.41% to 0.31% Using 61/2 Digit DMMby Direct/ ComparisonMethod
28 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
J Type ThermocoupleIndicator Controller/Recorder
-200°C to 1050°C 1.08°C Using ProcessCalibrator by DirectMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 4 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
29 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
K Type ThermocoupleIndicator Controller/Recorder
0°C to 1350°C 1.4°C Using ProcessCalibrator by DirectMethod
30 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
RTD (PT-100) IndicatorController/ Recorder
-200°C to 700°C 1.4°C Using ProcessCalibrator by DirectMethod
31 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
RType ThermocoupleIndicator Controller/Recorder
0°C to 1750°C 1.42°C Using ProcessCalibrator by DirectMethod
32 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
B Type ThermocoupleIndicatorcontroller/Recorder
100°Cto 1000°C
1.79 °C Using ProcessCalibrator by DirectMethod
33 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
J Type ThermocoupleIndicatorcontroller/Recorder
-200°C to 1050°C 1.44°C Using ProcessCalibrator by DirectMethod
34 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
K Type ThermocoupleIndicatorcontroller/Recorder
0°C to 1350°C 1.19°C Using ProcessCalibrator by DirectMethod
35 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
RTD (PT-100) Indicatorcontroller/Recorder
-200°C to 700°C 1.38°C Using ProcessCalibrator by DirectMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 5 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
36 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Frequency 10 Hz to 1 kHz 0.82% to 0.053% Using 61/2 Digit DMMby Direct/ ComparisonMethod
37 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Time 1 s to 3600 s 0.42s to 5s Using Time IntervalMeter by ComparisonMethod
38 MECHANICAL-ACCELERATION ANDSPEED
RPM Meter,Stroboscope, DigitalTachometer, Centrifuse(Non Contact Type)LC:- 0.1RPM
10 RPM to 1000 RPM 0.45% Using DigitalTachometer byComparison Method
39 MECHANICAL-ACCELERATION ANDSPEED
RPM Meter,Stroboscope, DigitalTachometer, Centrifuse(Non Contact Type)LC:- 1RPM
1000 RPM to 35000RPM
0.19% Using DigitalTachometer byComparison Method
40 MECHANICAL-ACOUSTICS
Sound Level Meter 94 dB to 114 dB 1.34dB Using Sound LevelCalibrator byComparison Method
41 MECHANICAL-DENSITY ANDVISCOSITY
Hydrometers , SpecificGravity Hydrometers,Lactometers, BrixHydrometers, SoilHydrometer
0.650 g/ml to 1.200g/ml
0.0011g/ml Using StandardHydrometer & Liquidsof known Densities
42 MECHANICAL-DENSITY ANDVISCOSITY
Hydrometers , SpecificGravity Hydrometers,Lactometers, BrixHydrometers, SoilHydrometer
1.200 g/ml to 1.800g/ml
0.0011g/ml Using StandardHydrometer & Liquidsof known Densities
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 6 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
43 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Depth Gauge L.C: 0.01mm
0 mm to 150 mm 11.6µm Using “0” Grade GaugeBlock Set &accessories byComparison method
44 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Depth Micro Meter L.C:0.01 mm
0 mm to 150 mm 11.6µm Using “0” Grade GaugeBlock Set &accessories byComparison method
45 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Thickness GaugeL.C: 0.01 mm
0 mm to 25 mm 8.0µm Using “0” Grade GaugeBlock Set &accessories byComparison method
46 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micro MeterLC: 0.001mm
0 mm to 100 mm 2.0µm Using “0” Grade GaugeBlock Set &accessories byComparison method
47 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micro MeterLC: 0.01mm
100 mm to 300 mm 9.0µm Using “0” Grade GaugeBlock Set &accessories byComparison method
48 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Feeler Gauge 0 mm to 2 mm 11.0µm Using Digital ExternalMicrometer byComparison method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 7 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
49 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height Gauge LC:0.01mm
0 mm to 300 mm 12µm Using “0” Grade GaugeBlock Set &accessories ,Surfaceplate by Comparisonmethod
50 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauge 3 mm to 100 mm 3.0µm Using “0” Grade GaugeBlock Set &accessories byComparison method
51 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Vernier/Dial/DigitalCalipers LC: 0.01mm
0 mm to 300 mm 10µm Using “0” Grade GaugeBlock Set &accessories byComparison method
52 MECHANICAL-MOBILE FORCEMEASURING SYSTEM
Digital / Analog PushPull Gauge , ForceGauge
100 N to 1000 N 0.51% Using NewtonianWeights & FrameFixture & Hangers
53 MECHANICAL-MOBILE FORCEMEASURING SYSTEM
Digital / Analog PushPull Gauge, ForceGauge
1 N to 100 N 0.61% Using NewtonianWeights & FrameFixture & Hangers
54 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure(Dial / Digital PressureGauge, PressureTransmitter, PressureSwitch, PressureValue, Transducer
>70 bar to 700 bar 0.41bar Using Digital PressureGauge & PressureComparator byComparison Method asper DKD-R6-1
55 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure(Dial / Digital PressureGauge, PressureTransmitter, PressureSwitch, PressureValue, Transducer
0 bar to 70 bar 0.09bar Using Digital PressureGauge & PressureComparator byComparison Method asper DKD-R6-1
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 8 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
56 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure(Dial / Digital PressureGauge, PressureTransmitter,Transducer
0 bar to 10 bar 0.011bar Using Digital PressureGauge & PressureComparator byComparison Method asper DKD-R6-1
57 MECHANICAL-PRESSUREINDICATING DEVICES
Vacuum Transmitter,Gauge (Digital / Dial)Vacuum Gauge,VacuumSwitch,Transducer
(-) 0.95 bar to 0 bar 0.022bar Using Digital PressureGauge by ComparisonMethod as per DKD-R6-1
58 MECHANICAL-VOLUME
Glassware, GlassPipette, Burette,Measuring Cylinder,Volume Flask,Beakers, MeasuringDispenser
1 ml to 25 ml 0.012 ml Using StandardWeights of Accuracyclass E2 and PrecisionBalances with andDistilled Water ofknown Density byGravimetric Method
59 MECHANICAL-VOLUME
Glassware, GlassPipette, Burette,Measuring Cylinder,Volume Flask,Beakers, MeasuringDispenser
25 ml to 150 ml 0.012 ml Using StandardWeights of Accuracyclass E2 and PrecisionBalances with andDistilled Water ofknown Density byGravimetric Method
60 MECHANICAL-VOLUME
Micropipette 100 µl to 10 ml 9µl Using StandardWeights of Accuracyclass E2 and PrecisionBalances with andDistilled Water ofknown Density byGravimetric Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 9 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
61 MECHANICAL-VOLUME
Micropipette 10µl to 100µl 0.3µl Using StandardWeights of Accuracyclass E2 and PrecisionBalances with andDistilled Water ofknown Density byGravimetric Method
62 MECHANICAL-VOLUME
Pipettes / Burrets /Measuring Flasks /Cylinders/Beakers ,Volumetric Measures/Glassware
150 ml to 1000 ml 1ml STD Weights &Electronics Balance
63 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 0.01mg &Coarser
1 g to 80 g 0.18mg Using StandardWeights of AccuracyClass E2
64 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 0.1g &Coarser
1 kg to 10 kg 0.71g Using StandardWeights of AccuracyClass F1 & F2 as perOIML R-76
65 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 0.1mg &Coarser
80 g to 200 g 0.60mg Using StandardWeights of AccuracyClass E2,
66 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 10 mg &Coarser
200 g to 5000 g 30mg Using StandardWeights of AccuracyClass E2 & F1
67 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 1g &Coarser
10 kg to 100 kg 3.7g Using StandardWeights of AccuracyClass F1 and F2
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 10 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
68 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
10 g 0.04 mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
69 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
1 g 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
70 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
1 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
71 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
10 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 11 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
72 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
100 g 0.15mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
73 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
100 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
74 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
2 g 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
75 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
2 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 12 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
76 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
20 g 0.04mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
77 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
20 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
78 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
200 g 0.20mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
79 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
200 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 13 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
80 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
5 g 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
81 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
5 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
82 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
50 g 0.10mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
83 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
50 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 14 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
84 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
500 mg 0.03mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
85 MECHANICAL-WEIGHTS
Weights 1 kg to 5 kg 80 mg std. weights &Electronic Balance
86 MECHANICAL-WEIGHTS
Weights 2 kg to 5 kg 26mg Using std. Weights &Electronic Balance
87 MECHANICAL-WEIGHTS
Weights 500 g to 1 kg 2mg std weights &Electronic Balance
88 THERMAL-TEMPERATURE
RTD , Thermocouplewith or withoutindicator, DigitalThermometer,Transmitter , DataLogger
20°C to 600°C 1.78°C Using 4 wire RTD with6.5 DMM byComparison Methodusing Dry BlockCalibrator
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 15 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
Site Facility
1 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 1 A to 10 A 0.065% to 0.055% Using 61/2 Digit DMMby Direct/ ComparisonMethod
2 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 1 mA to 400 mA 0.16% to 0.77% Using 61/2 Digit DMMby Direct/ ComparisonMethod
3 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 10 µA to 100 µA 1.0% to 0.63% Using 61/2 Digit DMMby Direct/ ComparisonMethod
4 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 100 µA to 1mA 0.093% to 0.09% Using 61/2 Digit DMMby Direct/ ComparisonMethod
5 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current @ 50Hz 400 mA to 1 A 0.77% to 0.065% Using 61/2 Digit DMMby Direct/ ComparisonMethod
6 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC High Voltage @ 50Hz
>1 kV to 5 kV 5.86% Using HV Probe withDMM by Direct Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 16 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
7 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Resistance 1 ohm to 100 kohm 1.04% to 1.01% Using LCR-Q Meter byDirect Method
8 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage @ 50Hz 1 mV to 100 mV 0.17% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
9 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage @ 50Hz 1 V to 100 V 0.1% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
10 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage @ 50Hz 100 mV to 1 V 0.1% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
11 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage@ 50Hz 100 V to 1000 V 0.1% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
12 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Capacitance 1µF to 100µF 4.13% to 2.01% Using LCR-Q Meter byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 17 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
13 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Inductance 1 mH to 10 H 2.16% to 0.68% Using LCR-Q Meter byDirect Method
14 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC High Current @50Hz
100 A to 900 A 3.55% Using Zeal MultiFunction Calibrator,51/2 Digit with CurrentCoil by Direct Method
15 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
DC High Current 100 A to 900 A 2.35% to 1.74% Using Zeal MultiFunction Calibrator,51/2 Digit with CurrentCoil by Direct Method
16 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Resistance (2-Wire) 200 M Ohm to 200 GOhm
1.42% to 5.15% Using High ResistanceBox, by Direct Method
17 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Resistance (4-Wire) 0.001 Ohm to 10 Ohm 2.4% Using Low ResistanceBox, by Direct Method
18 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 1 A to 10 A 0.55% to 0.26% Using 61/2 Digit DMMby Direct/ ComparisonMethod
19 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 1 mA to 400 mA 0.21% to 0.07% Using 61/2 Digit DMMby Direct/ ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 18 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
20 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 10µA to 100µA 1.21% to 0.1% Using 61/2 Digit DMMby Direct/ ComparisonMethod
21 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 100µA to 1mA 0.1% to 0.21% Using 61/2 Digit DMMby Direct/ ComparisonMethod
22 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 400 mA to 1 A 0.07% to 0.055% Using 61/2 Digit DMMby Direct/ ComparisonMethod
23 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Voltage 1 mV to 100 mV 0.40% to 0.40% Using 61/2 Digit DMMby Direct/ ComparisonMethod
24 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Voltage 100 mV to 1000 V 0.21% Using 61/2 Digit DMMby Direct/ ComparisonMethod
25 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance 0.001 Ohm to 1 Ohm 1.86% to 1.12% Using 61/2 Digit DMMby Direct/ ComparisonMethod
26 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance 1 ohm to 100 ohm 1.12% to 0.41% Using 61/2 Digit DMMby Direct/ ComparisonMethod
27 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance (2 wire) 1 MOhm to 100 MOhm 0.31% to 0.095% Using 61/2 Digit DMMby Direct/ ComparisonMethod
28 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance (2 wire) 100 Mohm to 1 Gohm 0.095% to 1.89% Using 61/2 Digit DMMby Direct/ ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 19 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
29 ELECTRO-TECHNICAL-MISCELLANEOUS(Measure)
Resistance (2 wire) 100 ohm to 1 Mohm 0.41% to 0.31% Using 61/2 Digit DMMby Direct/ ComparisonMethod
30 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
J Type ThermocoupleIndicator Controller/Recorder
-200°C to 1050°C 1.08°C Using ProcessCalibrator by DirectMethod
31 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
K Type ThermocoupleIndicator Controller/Recorder
0°C to 1350°C 1.4°C Using ProcessCalibrator by DirectMethod
32 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
RTD (PT-100) IndicatorController/ Recorder
-200°C to 700°C 1.4°C Using ProcessCalibrator by DirectMethod
33 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
RType ThermocoupleIndicator Controller/Recorder
0°C to 1750°C 1.42°C Using ProcessCalibrator by DirectMethod
34 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
B Type ThermocoupleIndicatorcontroller/Recorder
100°Cto 1000°C
1.79 °C Using ProcessCalibrator by DirectMethod
35 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
J Type ThermocoupleIndicatorcontroller/Recorder
-200°C to 1050°C 1.44°C Using ProcessCalibrator by DirectMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 20 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
36 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
K Type ThermocoupleIndicatorcontroller/Recorder
0°C to 1350°C 1.19°C Using ProcessCalibrator by DirectMethod
37 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
RTD (PT-100) Indicatorcontroller/Recorder
-200°C to 700°C 1.38°C Using ProcessCalibrator by DirectMethod
38 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Frequency 10 Hz to 1 kHz 0.82% to 0.053% Using 61/2 Digit DMMby Direct/ ComparisonMethod
39 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Time 1 s to 3600 s 0.42s to 5s Using Time IntervalMeter by ComparisonMethod
40 MECHANICAL-ACCELERATION ANDSPEED
RPM Meter,Stroboscope, DigitalTachometer, Centrifuse(Non Contact Type)LC:- 0.1RPM
10 RPM to 1000 RPM 0.45% Using DigitalTachometer byComparison Method
41 MECHANICAL-ACCELERATION ANDSPEED
RPM Meter,Stroboscope, DigitalTachometer, Centrifuse(Non Contact Type)LC:- 1RPM
1000 RPM to 35000RPM
0.19% Using DigitalTachometer byComparison Method
42 MECHANICAL-ACOUSTICS
Sound Level Meter 94 dB to 114 dB 1.34dB Using Sound LevelCalibrator byComparison Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 21 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
43 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure(Dial / Digital PressureGauge, PressureTransmitter, PressureSwitch, PressureValue, Transducer
>70 bar to 700 bar 0.41bar Using Digital PressureGauge & PressureComparator byComparison Method asper DKD-R6-1
44 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure(Dial / Digital PressureGauge, PressureTransmitter, PressureSwitch, PressureValue, Transducer
0 bar to 70 bar 0.09bar Using Digital PressureGauge & PressureComparator byComparison Method asper DKD-R6-1
45 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Uniaxial TestingMachine ,TensileTesting Machine,Compression TestingMachineCompressionCompression Mode
20 N to 1 kN 0.6% Using Force ProvingInstrument Class-1
46 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Uniaxial TestingMachine ,TensileTesting Machine,Compression TestingMachineCompressionTensionMode
20 N to 1 kN 1.02% Using Force ProvingInstrument Class-1
47 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Uniaxial TestingMachine ,TensileTesting Machine,Compression TestingMachineCompression
1 kN to 50 kN 0.82% Using Force ProvingInstrument Class-1 ofUTM.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 22 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
48 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Uniaxial TestingMachine ,TensileTesting Machine,Compression TestingMachineCompression
100 kN to 1000 kN 1.00% Using Force ProvingInstrument Class-1 ofUTM
49 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Uniaxial TestingMachine ,TensileTesting Machine,Compression TestingMachineTension
1 kN to 50 kN 0.88% Using Force ProvingInstrument Class-1 ofUTM.
50 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 0.01mg &Coarser
1 g to 80 g 0.18mg Using StandardWeights of AccuracyClass E2
51 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 0.1g &Coarser
1 kg to 10 kg 0.71g Using StandardWeights of AccuracyClass F1 & F2 as perOIML R-76
52 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 0.1mg &Coarser
80 g to 200 g 0.60mg Using StandardWeights of AccuracyClass E2,
53 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 10 mg &Coarser
200 g to 5000 g 30mg Using StandardWeights of AccuracyClass E2 & F1
54 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing BalanceReadability 1g &Coarser
10 kg to 100 kg 3.7g Using StandardWeights of AccuracyClass F1 and F2
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 23 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
55 MECHANICAL-WEIGHTS
Mass (Accuracy classF2 & coarser)
10 g 0.04 mg Using E2 AccuracyClass StandardWeights with WeighingBalance (Readability:0.01 mg & 0.1mg) bysubstitution method(ABBA cycle) as perOIML R–111: 2004
56 THERMAL- SPECIFICHEAT & HUMIDITY
Humidity Indicator OfHumidityCalibrator/Generator,Humidity Chamber
10 %RH to 95 %RH@25°C
1.7% Using Digital RHIndicator with SensorSingle PositionCalibration atmeasuring location inDUC
57 THERMAL-TEMPERATURE
Temperature IndicatorOf Dry Block Furnace/Muffle Furnace
0 to 1200 °C 2.24 °C Using Digital R-TypeThermocouple with61/2 digit multimeterSingle PositionCalibration atmeasuring location inDUC
58 THERMAL-TEMPERATURE
Temperature IndicatorOf Liquid Bath, Oven,Autoclave(IndustrialPurpose only ), BODIncubator (IndustrialPurpose only ),EnvironmentalChamber, Refrigerator,Deep Freezer
-80°C to 350°C 0.48°C Using RTD Sensor with6 ½ Digit MultimeterSingle PositionCalibration atmeasuring location inDUC
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTNCAL LABORATORY, PLOT NO-113, POCKET-A2, SECTOR-17,, NEW DELHI,DELHI, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2055 Page No. : 24 / 24
Validity 12/04/2019 to 11/04/2021 Last Amended on 07/06/2019