Download - Catalog Purator Eng
2007
} Dewatering Systems} Waste Water Purification} Sewage treatment} Infiltration} Building Drainage
ENGLISH
PolskaWarszawa
Slovenská RepublikaBratislava
MagyaroszágBudapest
RomâniaBucharest
Srbija i Crna GoraBeograd
Bosna i HercegovinaSarajevo
HrvatskaZagreb
SlovenijaTrzin
ÖSTERREICHWien
Česká RepublikaBrno
l
lll
l
lll
ll
l
БългарияBurgas
�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Table of contents
Manhole covers 4Steel and stainless steel covers 19Athlet safety equipment 22Alupura® 24Recessed covers 25Gully grates and tops 27Kerb gullies 36Bridge drainage systems 37Steel gratings, hot-dip galvanised 39Street and yard gullies 40Slotted buckets and dirt pans 43Surface boxes and hydrant cases 44Historical casting 45Box gutters 49
Dewatering systems
Cesspools 56Sewage treatment plants 60Mineral oil seperators 63Grease seperators 74Conveyor technique 93Concrete parts 106
Waste water purificaton
Kanalith - concrete shaft system 112Puraplast PE manhole 114Boxless sliding gates 119Back-water gates and antiflooding valves 122Pipe ducts 129
Sewage treatment
Roof outlets 142Floor drains 145Stainless steel channels and trays 153Basement drains and heating oil stops 158Rainwater drains 160
Building drainage
Infiltration 132Infiltration
Terms & Conditions 164Terms & Conditions
�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Place of installation and loadings for manhole cover and gully grate
The appropriate class of manhole cover and gully grate to be used depends on the place of installation. The various places of in-stallation have been divided into groups numbered 1 to 6. The selection of the appropriate class is the responsibility of the designer. Where there is any doubt the stronger class should be selected.
Group 1 (mind. class A 015): Areas which can only be used by pedestrians and pedal cyclists.
Group 2 (mind. class B 125): Footways, pedestrian areas and comparable areas, car parks or car parking decks.
Group 3 (mind. class C 250): For gully tops installed in the area of kerbside channels of roads which when measured from the kerb edge extend a maximum of 0.5m into the carriageway and a maximum of 0.2m in to the footway.
Group 4 (mind. class D 400): Carriageway of roads (including pedestrian streets), hard shoulders and parking areas for all types of road vehicles.
Group 5 (mind. class E 600): Areas imposing high wheel loads eg. docks and aircraft pavements
Group 6 (mind. class F 900): Areas imposing particularly high wheel loads eg. aircraft pavements
Further Loacing classes (conforming ÖN EN1253)
Class H 1,5: (1,5 kN) for non-accessible flat roof areas eg. gravel-bed roof
K 3: (3 kN) for non-accessible areas without rolling traffic eg. indoor areas, such as bathroom in hotels, schools, public swimming pools, terraces and patios L 15: (15 kN) for areas accessed by light-weight traffic up to vehicles with a total weight of not more than 200 kg (indoors at commercial or industrial sites)
M 125: (125 kN) ffor areas accessed by passenger cars eg. parking garages, workshops and factories
Loading class extension (for higher loads) eg.:
Class L 50: (50 kN) like class L 15, reinforced design M 250: (250 kN) like class M 125, reinforced design M 400: (400 kN) like class M 125, reinforced design
Outlets and gratings indoors (DIN 19599)Class L 15: (15 kN) for areas accessed by light-weight traffic without forklifts in commercial or industrial buildings M 125: (125 kN) for areas accessed by passenger cars, eg. parking garages, workshops and factories (for all areas with with exposure to special loadings, eg. exhibition halls, market halls, factory halls, hangars etc. use the appropriate manhole covers and gratings according to DIN EN 124/DIN 1229, Class C 250 up to F 900)
Dewa
terin
g sy
stem
s
�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Table of contentsDewatering systems
Manhole covers 4
Steel and stainless steel covers 19
Safety equipment 22
Alupura® 24
Recessed covers 25
Gully grates and tops 27
Kerb gullies 36
Bridge drainage systems 37
Steel gratings, hot-dip galvanised 39
Street and yard gullies 40
Slotted buckets and dirt pans 43
Surface boxes and hydrant cases 44
Historical casting 45
Box gutters 49
Manh
ole T
ops
�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Manhole tops DN 600
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: cast ironnon-ventilated/ventilatedexchangeableFrame: cast iron, round
ä with cushioning insertÖWAPREN ...D
11015(-1) 610mm / 70mm / 18mm A 015 54 021 u.r.11125(-1) 610mm / 70mm / 18mm B 125 73 021 u.r.11250(-1) 610mm / 70mm / 18mm C 250 75 021 u.r.11400(-1) 610mm / 100mm / 50mm D 400 133 021 u.r.11400D(-1D)ä 610mm / 100mm / 50mm D 400 133 021 u.r.11600(-1) 610mm / 100mm / 50mm E 600 133 021 u.r.11600D(-1D)ä 610mm / 100mm / 50mm E 600 133 021 u.r.
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: cast ironnon-ventilated/ventilatedexchangeableFrame: cast iron, with square seating
ä with cushioning insertÖWAPREN ...D
12015(-1) 610mm / 70mm / 18mm A 015 66 021 u.r.12125(-1) 610mm / 70mm / 18mm B 125 80 021 u.r.12250(-1) 610mm / 70mm / 18mm C 250 82 021 u.r.12400(-1) 610mm / 100mm / 50mm D 400 145 021 u.r.12400D(-1D)ä 610mm / 100mm / 50mm D 400 145 021 u.r.12600(-1) 610mm / 100mm / 50mm E 600 145 021 u.r.12600D(-1D)ä 610mm / 100mm / 50mm E 600 145 021 u.r.12900(-1) 610mm / 100mm / 50mm F 900 139 021 u.r.12900D(-1D)ä 610mm / 100mm / 50mm F 900 139 021 u.r.
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: cast ironnon-ventilated/ventilatedexchangeableFrame: concrete/cast iron, round
ä with cushioning insertÖWAPREN ...D
17015(-1) 610mm / 130mm / 18mm A 015 91 021 u.r.17125(-1) 610mm / 130mm / 18mm B 125 109 021 u.r.17250(-1) 610mm / 130mm / 18mm C 250 111 021 u.r.17400(-1) 610mm / 160mm / 50mm D 400 186 021 u.r.17400D(-1D)ä 610mm / 160mm / 50mm D 400 186 021 u.r.17600(-1) 610mm / 160mm / 50mm E 600 193 021 u.r.17600D(-1D)ä 610mm / 160mm / 50mm E 600 193 021 u.r.17900(-1) 610mm / 160mm / 50mm F 900 173 021 u.r.17900D(-1D)ä 610mm / 160mm / 50mm F 900 173 021 u.r.
l Oewapren cushioning insert Art. No. Description Class € / piece
supplied with cushioning insert pressed into cover ring groove made of wear-resistant NBR for topswith item numbers .....D (-1D)
..... D (-1D)only available for manhole tops with
50 mm insertion depth (from class D 400)
from D 400 u.r.
Manh
ole T
ops
�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Manhole tops DN 600
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: cast ironnon-ventilated/ventilatedexchangeableFrame: concrete/cast iron, square-shaped
ä with cushioning insertÖWAPREN ...D
18015(-1) 610mm / 130mm / 18mm A 015 140 021 u.r.18125(-1) 610mm / 130mm / 18mm B 125 158 021 u.r.18250(-1) 610mm / 130mm / 18mm C 250 158 021 u.r.18400(-1) 610mm / 160mm / 50mm D 400 257 021 u.r.18400D(-1D)ä 610mm / 160mm / 50mm D 400 257 021 u.r.18600(-1) 610mm / 160mm / 50mm E 600 261 021 u.r.18600D(-1D)ä 610mm / 160mm / 50mm E 600 261 021 u.r.18900(-1) 610mm / 160mm / 50mm F 900 233 021 u.r.18900D(-1D)ä 610mm / 160mm / 50mm F 900 233 021 u.r.
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: concrete/cast ironnon-ventilated/ventilatedexchangeableFrame: cast iron, round
ä with cushioning insertÖWAPREN ...D
81015(-1) 610mm / 70mm / 18mm A 015 69 021 u.r.81125(-1) 610mm / 70mm / 18mm B 125 69 021 u.r.81250(-1) 610mm / 70mm / 18mm C 250 69 021 u.r.81400(-1) 610mm / 100mm / 50mm D 400 124 021 u.r.81400D(-1D)ä 610mm / 100mm / 50mm D 400 124 021 u.r.81600(-1) 610mm / 100mm / 50mm E 600 124 021 u.r.81600D(-1D)ä 610mm / 100mm / 50mm E 600 124 021 u.r.
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: oncrete/cast ironnon-ventilated/ventilatedexchangeableFrame: cast iron, with square-shaped seating
ä with cushioning insertÖWAPREN ...D
82015(-1) 610mm / 70mm / 18mm A 015 79 021 u.r.82125(-1) 610mm / 70mm / 18mm B 125 79 021 u.r.82250(-1) 610mm / 70mm / 18mm C 250 79 021 u.r.82400(-1) 610mm / 100mm / 50mm D 400 136 021 u.r.82400D(-1D)ä 610mm / 100mm / 50mm D 400 136 021 u.r.82600(-1) 610mm / 100mm / 50mm E 600 136 021 u.r.82600D(-1D)ä 610mm / 100mm / 50mm E 600 136 021 u.r.82900(-1) 610mm / 100mm / 50mm F 900 136 021 u.r.82900D(-1D)ä 610mm / 100mm / 50mm F 900 136 021 u.r.
l Oewapren cushioning insert Art. No. Description Class € / piece
supplied with cushioning insert pressed into cover ring groove made of wear-resistant NBR for topswith item numbers .....D (-1D)
..... D (-1D)only available for manhole tops with
50 mm insertion depth (from class D 400)
from D 400 u.r.
Manh
ole T
ops
6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Manhole tops DN 600
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: concrete/cast ironnon-ventilated/ventilatedexchangeableFrame: concrete/cast iron, round
ä with cushioning insertÖWAPREN ...D
87015(-1) 610mm / 130mm / 18mm A 015 106 021 u.r.87125(-1) 610mm / 130mm / 18mm B 125 107 021 u.r.87250(-1) 610mm / 130mm / 18mm C 250 109 021 u.r.87400(-1) 610mm / 160mm / 50mm D 400 196 021 u.r.87400D(-1D)ä 610mm / 160mm / 50mm D 400 196 021 u.r.87600(-1) 610mm / 160mm / 50mm E 600 209 021 u.r.87600D(-1D)ä 610mm / 160mm / 50mm E 600 209 021 u.r.
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: concrete/cast ironnon-ventilated/ventilatedexchangeableFrame: concrete/cast iron, square-shaped
ä with cushioning insertÖWAPREN ...D
88015(-1) 610mm / 130mm / 18mm A 015 151 021 u.r.88125(-1) 610mm / 130mm / 18mm B 125 151 021 u.r.88250(-1) 610mm / 130mm / 18mm C 250 153 021 u.r.88400(-1) 610mm / 160mm / 50mm D 400 266 021 u.r.88400D(-1D)ä 610mm / 160mm / 50mm D 400 266 021 u.r.88600(-1) 610mm / 160mm / 50mm E 600 279 021 u.r.88600D(-1D)ä 610mm / 160mm / 50mm E 600 279 021 u.r.
l Oewapren cushioning insert Art. No. Description Class € / piece
supplied with cushioning insert pressed into cover ring groove made of wear-resistant NBR for topswith item numbers .....D (-1D)
..... D (-1D)only available for manhole tops with
50 mm insertion depth (from class D 400)
from D 400 u.r.
Cover with insert Art. No. Description Class € / piece
various designs possible,including lettering and emblems
-
Emblem in cast coverLettering in cast cover
Emblem in cast concrete cover as needed u.r.
cast iron lettering plate Art. No. Description Class € / piece
for concrete/cast iron covermatching ÖN/EN manhole top DN 600 - cast iron lettering plate
in Beton-GusseisenCover as needed u.r.
ä conforming to the standard as appropriate
Manh
ole T
ops
�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Manhole tops DN 600 and DN 800, bolted, backflow-proof
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: cast iron with 4 boltsFrame: cast iron, roundClear opening between frame and cover completely free (no projections from thread)Cover is easy to exchangeTightness versus the structure – on the side of the buildingl tight and backflow-proof up to 0.5 bar
11015RS1 610mm / 70mm / 18mm A 015 55 021 u.r.11125RS1 610mm / 70mm / 18mm B 125 74 021 u.r.11250RS1 610mm / 70mm / 18mm C 250 76 021 u.r.11400RS2 610mm / 100mm / 50mm D 400 134 021 u.r.11600RS2 610mm / 100mm / 50mm E 600 134 021 u.r.
SCHL6 Key for 1, SW 18 mm 0,6 030 u.r.SCHL4 Key for 2, SW 18/22 mm 1,3 030 u.r.
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: cast iron with 4 boltsFrame: cast iron, with square seatingClear opening between frame and cover completely free (no projections from thread)Cover is easy to exchangeTightness versus the structure – on the side of the building
l tight and backflow-proof up to 0.5 bar
12015RS1 610mm / 70mm / 18mm A 015 70 021 u.r.12125RS1 610mm / 70mm / 18mm B 125 89 021 u.r.12250RS1 610mm / 70mm / 18mm C 250 79 021 u.r.12400RS2 610mm / 100mm / 50mm D 400 145 021 u.r.12600RS2 610mm / 100mm / 50mm E 600 151 021 u.r.12900RS2 610mm / 100mm / 50mm F 900 136 021 u.r.
SCHL6 Key for 1, SW 18 mm 0,6 030 u.r.SCHL4 Key for 2, SW 18/22 mm 1,3 030 u.r.
Manhole top, DN 600 manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group € / piece
Cover: cast iron with 4 boltsFrame: Concrete/cast iron, round Clear opening between frame and cover completely free (no projections from thread)Cover is easy to exchangeTightness versus the structure – on the side of the buildingl tight and backflow-proof up to 0.5 bar
17015RS1 610mm / 130mm / 18mm A 015 93 021 u.r.17125RS1 610mm / 130mm / 18mm B 125 106 021 u.r.17250RS1 610mm / 130mm / 18mm C 250 111 021 u.r.17400RS2 610mm / 160mm / 50mm D 400 193 021 u.r.17600RS2 610mm / 160mm / 50mm E 600 196 021 u.r.
SCHL6 key for 1, SW 18 mm 0,6 030 u.r.SCHL4 key for 2, SW 18/22 mm 1,3 030 u.r.
Screw-on manhole top made from SGCI, backflow-proofmanufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg)
Price group
€ / piece
Cover: screw-on cast ironClear opening between frame and cover completely free
l tight and backflow-proof up to 0.5 bar; with PAM-DICHT up to 1 bar
Frame round11250RS-SGCI DN 600 / 75mm / 50mm C 250 50 020 u.r.PM-11400RS u DN 600 / 100mm / 50mm D 400 84 130 u.r.11400RS-800Nä DN 800 / 108mm / 50mm D 400 132 020 u.r.
Frame square-shaped12400RS-800 DN 800 RH 100mm / 50mm D 400 145 130 u.r.ä with flat iron and screws
Image shows PAMDICHT u
Manh
ole T
ops
�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Manhole tops made of SGCI, DN 600
Type Footpathconforms to ÖN/EN 124 Art. No. Description Class Weight
(kg)Price group
€ / piece
Cover: SGCIFrame: SGCI
for footpaths, car parks and parking decks – especially suitable for mastic asphalt!
Frame roundPM-11125 DN 600, h 35mm B 125 39 130 u.r.
Type Mediumconforms to ÖN/EN 124 Art. No. Description Class Weight
(kg)Price group
€ / piece
Cover: SGCIFrame: SGCIwith cushioning insert
for footpaths, passenger car parking and parking decks
Frame roundPM-11125D DN 600, h 75mm B 125 50 130 u.r.
Frame with square seating (without picture)PM-12125D DN 600, h 75mm B 125 56 130 u.r.
Type Paysageconforms to ÖN/EN 124 Art. No. Description Class Weight
(kg)Price group
€ / piece
Cover: SGCIFrame: SGCIwith cushioning insert
for kerb and spaces trafficked at low speeds
Frame roundPM-11250D DN 600, h 75mm C 250 53 130 u.r.
Frame with square seating (without picture)PM-12250D DN 600, h 75mm C 250 60 130 u.r.
Type Rexelconforms to ÖN/EN 124 Art. No. Description Class Weight
(kg)Price group
€ / piece
Cover: SGCIFrame: SGCIfor urban traffic in traffic-calmed areas with hinge andauto-bolting with cushioning insert
with cushioning insertl not to be used in combinati-on with dirt pan!
non-ventilatedPM-11400VD DN 600, h 100mm D 400 57 130 u.r.
ventilatedPM-11400V-1D DN 600, h 100mm D 400 56 130 u.r.
Manh
ole T
ops
�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Manhole tops made of SGCI, DN 600
Type Pamrexmanufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description Class Weight
(kg)Price group € / piece
Cover: SGCIFrame: SGCIfor heavily trafficked roadswith hinge (lockable at 90°)with cushioning insert
l with square-shaped Frame on request
non-ventilatedPM-11400D DN 600, h 100mm D 400 88 130 u.r.
PM-11400D-700 DN 700, h 100mm D 400 108 130 u.r.
ventilatedPM-11400-1D DN 600, h 100mm D 400 88 130 u.r.
PM-11400-1D-700 DN 700, h 100mm D 400 108 130 u.r.
with double hingePM-11400DS-80 DN 800, h 100mm D 400 125 130 u.r.
PM-11400-1DS-80 DN 800, h 100mm D 400 124 130 u.r.
PM-11400DS-80GFä DN 800, h 100mm D 400 129 130 u.r.ä with pneumatic spring as lifting aid
Concrete compensating ring Art. No. Description Weight (kg)
Price group € / piece
PM-AGR-PAM displacement-proof for DN 600 50 130 u.r.
Dirt pangalvanised, with crossbar
Pricegroup 130
Art. No. Description DN € / piecePM-SF displacement-proof 600
l ventilated for PAMREX-covers
Locking devicesno image
Pricegroup 130
Art. No. Description € / piecePM-SPS Bolting set for Rexel u.r.PM-SP Lock for Rexel u.r.PM-S Key only for Rexel u.r.PM-RE38H9Y Bolting set for Pamrex u.r.PM-RE80H9U bolting set for DN800 Viatop u.r.
Type Urbamaxconforms to ÖN/EN 124 Art. No. Description Class Weight
(kg)Price group € / piece
Cover: SGCIFrame: SGCI
for heavy-vehicle trafficwith cushioning insert
lclatter-free!
non-ventilatedPM-11600D DN 600, h 100mm E 600 93 130 u.r.
PM-11900D DN 600, h 100mm F900 93 130 u.r.
ventilatedPM-11600-1D DN 600, h 100mm E 600 93 130 u.r.
PM-11900-1D DN 600, h 100mm F900 93 130 u.r.
Manh
ole T
ops
�0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Manhole tops made of SGCI, DN 600
Type Viatop-Standardconforms ÖN/EN 124 ON CERT as well as ÖN B5110
Art. No. Description Class Weight (kg)
Price group € / piece
Cover: SGCIFrame: SGCI
for heavily trafficked roads
with hinge (lockable at 90°)
l clatter-free!
non-ventilatedPM-16400D DN 600, h 100mm D 400 83 130 u.r.
ventilatedPM-16400-1D DN 600, h 100mm D 400 81 130 u.r.
Cover: concrete-SGCIFrame: SGCI
for heavily trafficked roads
with hinge (lockable at 90°)
l clatter-free!
non-ventilatedPM-86400D DN 600, h 100mm D 400 105 130 u.r.
ventilatedPM-86400-1D DN 600, h 100mm D 400 104 130 u.r.
Type Dynatopwith Duo spring lock conforms ÖN/EN 124
Art. No. Description Class Weight (kg)
Price group € / piece
Cover: SGCIFrame: SGCI
smooth, drawable frame,non-slip surface,Composite insert, 90°safety lock
l clatter-free!
non-ventilatedPM-DYNATOP DN 600, h 110 mm D 400 65 130 u.r.
ventilatedPM-DYNATOP-1 DN 600, h 110 mm D 400 64 130 u.r.PM-SF matching dirt pan, DN 600 130 u.r.l Insert of emblem or lettering on request
NEW!
Dirt pangalvanised, with crossbar Art. No. Description DN Weight
(kg)Price group € / piece
PM-SF for Standard and Dynatop 600 7,5 130 u.r.
Manh
ole T
ops
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type Viatop-Niveauconforms ÖN/EN 124 ON CERT as well as ÖN B5110
Cover surface with dirt-repellent design, self-levelling up to 8 cm,for roads with heavy traffic, rutting and frequent repaving,heavy traffic, sections trafficked by braking vehicles and inclined bends
Art. No. Description Class Weight (kg)
Price group € / piece
Cover: SGCIFrame: SGCI
with hinge (lockable at 90°)
l secured against twis-ting; absolutely clatter-free due to cushioning insert
non-ventilatedPM-NIVEAU DN 600, h 200mm D 400 102 130 u.r.PM-NIVEAU-N ä DN 600, h 140mm Rehab D 400 90 130 u.r.
ventilatedPM-NIVEAU-1 DN 600, h 200mm D 400 102 130 u.r.PM-NIVEAU-1N ä DN 600, h 140mm Rehab D 400 90 130 u.r.ä (N)... up to 4 cm self-levelling
Special adapter rings made of concrete for VIATOP-Niveauwith dual reinforcement and larger clear opening
Pricegroup 130
Art. No. Description DN Weightkg € / piece
PM-A-RING-BE60 h 60mm, f. Rehab 690 20 u.r.PM-A-RING-BE90 h 90mm, Standard 690 35 u.r.PM-A-RING-BE130 h 130mm, special height 690 66 u.r.
ditto, made of SGCIPM-A-RING-SGCI h 135mm 690 20 u.r.l cannot be replaced by standard concrete compensating ring!
MEI - LEVEL manhole tops and gully grates
Type MEI - LEVEL conforms ÖN/EN 124 ON CERT as well as ÖN B5110 Art. No. Description Class Weight
(kg)Price group € / piece
Cover: cast ironFrame: cast iron
Concrete ring included
l Sliding frame and concrete ring also available individual-ly for rehabilitation
non-ventilatedML-11400 DN 600, h 160mm D 400 177 021 u.r.ML-11400D DN 600, h 160mm D 400 177 021 u.r.ML-11600 DN 600, h 160mm E 600 183 021 u.r.ML-11600D DN 600, h 160mm E 600 183 021 u.r.
ventilatedML-11400-1 DN 600, h 160mm D 400 177 021 u.r.ML-11400-1D DN 600, h 160mm D 400 177 021 u.r.ML-11600-1 DN 600, h 160mm E 600 183 021 u.r.ML-11600-1D DN 600, h 160mm E 600 183 021 u.r.
Channel-shaped gratingML-31400 DN 600, h 160mm D 400 177 021 u.r.ML-31400D DN 600, h 160mm D 400 177 021 u.r.
Manhole tops made of SGCI/cast iron DN 600
Manh
ole T
ops
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
VARIOTECH® single, row and multiple tops
VARIOTECH®
Row and multiple tops made of spheroidal graphite cast iron, interface of frame and cover mechanically worked, screwed and greased for impermeability to surface water
1-unit standard model Row covers without intermediate bracing
2-unit standard model 3-unit standard model Multiple tops with removable bracing
l The programme covers classes B125, C250, D400, E600
Range of application:VARIOTECH®-manhole tops (Pame-
tic system) are used to cover subter-ranean shafts including energy supply ducts, sand traps, flushing dumps, gate chambers, etc. They are suitable for use in municipal, district heating, telecom and industrial operations as they prevent entry of dirt and water and ensure easy access to the machi-nes, facilities and equipment located below.
Production description:VARIOTECH®-manhole tops are
single- or multiple manhole tops. Two types of surfaces are available:
• closed cast surface with anti-slip nubs
• recessed design for filling with con-crete
The individual manhole tops form a modular system and can be combined ad lib to form rows or areas permitting covering shafts of a wide variety of sizes. Covers and frames are manuf-actured for perfect fit to prevent any slipping and clattering.
The products are designed and ma-nufactured for easy installation of the manhole tops and easy operation af-ter installation. The top is secured by screws against unauthorised access.
VARIOTECH®-manhole tops are made of high-quality spheroidal gra-phite cast iron, of lighter weight than equivalent covers made of grey cast iron and thus particularly easy to handle.
Even in multi-part assemblies, co-vers can be opened individually in any order desired.
l VARIOTECH® Type PM-G2 with screwed frame, for range of products see the next page
Manh
ole T
ops
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
VARIOTECH® Pametic 2 Single and row covers
Typ Pametic 2 Single and row covers Pricegroup 136
Art. No. Clear openingmm Class no. of
Cover Model € / piece
PM-G2-4545BFE 450 x 450 B 125 1 fill-in cover u.r.PM-G2-6045BFE 600 x 450 B 125 1 fill-in cover u.r.PM-G2-7560BFE 750 x 600 B 125 1 fill-in cover u.r.PM-G2-10045BFR 1000 x 450 B 125 2 fill-in cover u.r.PM-G2-14560BFR 1450 x 600 B 125 2 fill-in cover u.r.
PM-G2-4545BGE 450 x 450 B 125 1 solid casting u.r.PM-G2-7575BGE 750 x 750 B 125 1 solid casting u.r.PM-G2-10045BGR 1000 x 450 B 125 2 solid casting u.r.PM-G2-13060BGR 1300 x 600 B 125 2 solid casting u.r.
PM-G2-4545CFE 450 x 450 C 250 1 fill-in cover u.r.PM-G2-6045CFE 600 x 450 C 250 1 fill-in cover u.r.PM-G2-7560CFE 750 x 600 C 250 1 fill-in cover u.r.PM-G2-10045CFR 1000 x 450 C 250 2 fill-in cover u.r.PM-G2-14560CFR 1450 x 600 C 250 2 fill-in cover u.r.
PM-G2-4545CGE 450 x 450 C 250 1 solid casting u.r.PM-G2-7575CGE 750 x 750 C 250 1 solid casting u.r.PM-G2-10045CGR 1000 x 450 C 250 2 solid casting u.r.PM-G2-13060CGR 1300 x 600 C 250 2 solid casting u.r.
PM-G2-6045DFE 600 x 450 D 400 1 fill-in cover u.r.PM-G2-9060DFE 900 x 600 D 400 1 fill-in cover u.r.PM-G2-7590DFE 750 x 900 D 400 1 fill-in cover u.r.PM-G2-13060DFR 1300 x 600 D 400 2 fill-in cover u.r.
PM-G2-9090DGE 900 x 900 D 400 1 solid casting u.r.PM-G2-12075DGE 750 x 1200 D 400 1 solid casting u.r.PM-G2-130120DGR 1300 x 1200 D 400 2 solid casting u.r.
NEW!
Keyup to 600
Pricegroup 136
Art. No. € / piecePM-RL60R8B u.r.
Keylarger than 600
Pricegroup 136
Art. No. € / piecePM-RL60R8A u.r.
Cover lifter set 2 cover lifter and 1 flat wrench
Pricegroup 136
Art. No. € / piecePM-RL60R8E u.r.
Frame depth 75 mm,for all Class B and C tops
Frame depth 140 mm, for all Class D, E and F tops
Manh
ole T
ops
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Cast iron manhole tops, rectangular
Series 1047 special topsclear opening 400x250 Art. No. Description Class Weight
(kg)Price group € / piece
Cover: cast ironFrame: cast iron
1047A 400mm x 250mm, h 65mm D 400 56 030 u.r.impermeable to surface water between frame and top1047A-OE400 400mm x 250mm, h 65mm D 400 56 030 u.r.
Series 1047clear opening 600x400 Art. No. Description
e x f, h Class Weight (kg)
Price group € / piece
installation depth = 20 mm(400kN, screwed, 30 mm)
1047G015-I 600mm x 400mm, h 60mm A 15 35 030 u.r.1047G125-I 600mm x 400mm, h 60mm B 125 49 030 u.r.1047G250-I 600mm x 400mm, h 60mm C 250 54 030 u.r.1047G400-I 600mm x 400mm, h 80mm D 400 88 030 u.r.water-tight, 4 screws connecting frame and cover1047G-OE015-I 600mm x 400mm, h 60mm A 15 35 030 u.r.1047G-OE125-I 600mm x 400mm, h 60mm B 125 49 030 u.r.1047G-OE250-I 600mm x 400mm, h 60mm C 250 54 030 u.r.1047G-OE400-I 600mm x 400mm, h 80mm D 400 88 030 u.r.
Series 1047Rclear opening 800x600 Art. No. Description
e x f, h Class Weight (kg)
Price group € / piece
Installation depth = 30 mm (400kN screwed)
1047R015-I 800mm x 600mm, h 80mm A 15 85 030 u.r.1047R125-I 800mm x 600mm, h 80mm B 125 100 030 u.r.1047R250-I 800mm x 600mm, h 80mm C 250 115 030 u.r.1047R400-I 800mm x 600mm, h 80mm D 400 115 030 u.r.water-tight, 4 screws connecting frame and cover1047R-OE015-I 800mm x 600mm, h 80mm A 15 85 030 u.r.1047R-OE125-I 800mm x 600mm, h 80mm B 125 100 030 u.r.1047R-OE250-I 800mm x 600mm, h 80mm C 250 115 030 u.r.1047R-OE400-I 800mm x 600mm, h 80mm D 400 115 030 u.r.
Series 1047Sclear opening 1000x600 Art. No. Description
e x f, h Class Weight (kg)
Price group € / piece
Installation depth = 30 mm (400kN screwed)
1047S015-I 1000mm x 600mm, h 80mm A 15 90 030 u.r.1047S125-I 1000mm x 600mm, h 80mm B 125 120 030 u.r.1047S250-I 1000mm x 600mm, h 80mm C 250 145 030 u.r.1047S400-I 1000mm x 600mm, h 80mm D 400 145 030 u.r.water-tight, 4 screws connecting frame and cover1047S-OE015-I 1000mm x 600mm, h 80mm A 15 90 030 u.r.1047S-OE125-I 1000mm x 600mm, h 80mm B 125 120 030 u.r.1047S-OE250-I 1000mm x 600mm, h 80mm C 250 145 030 u.r.1047S-OE400-I 1000mm x 600mm, h 80mm D 400 145 030 u.r.
E
E
F
F New model: without bevelled edge, (phase-out models with bevelled edge = different frame depths!!)
Manh
ole T
ops
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Cast iron manhole tops, square-shaped
Series 1048 A-FSpecial sizes Art. No. Description Inst.
depth Class Weight (kg)
Price group € / piece
1048A* a 300mm, h 65mm 12mm A 15 16 030 u.r.1048A1* a 300mm, h 70mm 25mm A 50 30 030 u.r.1048D* a 400mm, h 90mm 13mm A 50 28 030 u.r.1048D1* a 400mm, h 85mm 40mm C 250 64 030 u.r.1048F* a 500mm, h 65mm 30mm A 15 37 030 u.r.
Series 1048Xclear opening 600x600 Art. No. Description
e x f, h Class Weight (kg)
Price group € / piece
Installation depth = 30 mm (400kN screwed)
1048X015-I 600mm x 600mm, h 60mm A 15 51 030 u.r.1048X125-I 600mm x 600mm, h 60mm B 125 66 030 u.r.1048X250-I 600mm x 600mm, h 60mm C 250 72 030 u.r.1048X400-I 600mm x 600mm, h 80mm D 400 110 030 u.r.water-tight, 4 screws connecting frame and cover1048X-OE015-I 600mm x 600mm, h 60mm A 15 51 030 u.r.1048X-OE125-I 600mm x 600mm, h 60mm B 125 66 030 u.r.1048X-OE250-I 600mm x 600mm, h 60mm C 250 72 030 u.r.1048X-OE400-I 600mm x 600mm, h 80mm D 400 110 030 u.r.
Type AKSESSmanufactured to EN 124 for buildings Art. No. Description Class Weight
(kg)Price group € / piece
Cover: SGCIFrame: SGCIwith three-point support
PM-AKS220 Type 300 - e 220 mm, h 37 mm B 125 8,2 130 u.r.PM-AKS300 Type 400 - e 300 mm, h 37 mm B 125 11,8 130 u.r.PM-AKS350 Type 450 - e 350 mm, h 38 mm B 125 15,2 130 u.r.PM-AKS400 Type 500 - e 400 mm, h 38 mm B 125 18,2 130 u.r.PM-AKS500 Type 600 - e 500 mm, h 38 mm B 125 29,4 130 u.r.PM-AKS600 Type 700 - e 600 mm, h 38 mm B 125 39,8 130 u.r.PM-AKS700 Type 800 - e 700 mm, h 41 mm B 125 52,6 130 u.r.
Type PARXESSmanufactured to EN 124, not ÜA-certified Art. No. Description Class Weight
(kg)Price group € / piece
Cover: SGCIFrame: SGCIwith three-point support
PM-PAKS300 Type 400 - e 300 mm, h 56 mm C 250 11,8 130 u.r.PM-PAKS400 Type 500 - e 400 mm, h 56 mm C 250 18,2 130 u.r.PM-PAKS500 Type 600 - e 500 mm, h 56 mm C 250 29,4 130 u.r.PM-PAKS600 Type 700 - e 600 mm, h 56 mm C 250 38,8 130 u.r.l Surcharge for bolting upon request
Service key for OE… modelArt. No. Description Pricegroup € / pieceSteckschlüssel M17 wrench for hexagon screw connection 030 u.r.INBUS10 Allen key for countersunk screw 030 u.r.
Manh
ole T
ops
�6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Cast iron manhole tops, square-shaped
Series 1048Zclear opening 800x800 Art. No. Description
e x f, h Class Weight (kg)
Price group € / piece
Installation depth = 30 mm (400kN screwed)
External dimension 880 x 880 mm
1048Z015-I 800mm x 800mm, 80mm A 15 160 030 u.r.1048Z125-I 800mm x 800mm, 80mm B 125 160 030 u.r.1048Z250-I 800mm x 800mm, 80mm C 250 160 030 u.r.1048Z400-I 800mm x 800mm, 80mm D 400 160 030 u.r.water-tight, 4 screws connecting frame and cover1048Z-OE015-I 800mm x 800mm, 80mm A 15 160 030 u.r.1048Z-OE125-I 800mm x 800mm, 80mm B 125 160 030 u.r.1048Z-OE250-I 800mm x 800mm, 80mm C 250 160 030 u.r.1048Z-OE400-I 800mm x 800mm, 80mm D 400 160 030 u.r.
E
F New model: without bevelled edge, (phase-out models with bevelled edge = different frame depths!!)
Fuel tank cover Art. No. Descriptione x f, h Class Weight
(kg)Price group € / piece
Installation depth = 30 mm,
impermeable to surface water between frame and top top with central cover (incl. seal and bayonet catch) for measuring fill level
1048Z-FÜLL400 800mm x 800mm, 100mm D 400 274 030 u.r.
SCHL1048Z-FÜLL Key to this top 1 030 u.r.
Series 1048Uclear opening 1003x1003 Art. No. Description
e x f, h Class Weight (kg)
Price group € / piece
Installation depth = 30 mm (400kN screwed)
External dimension 1120 x 1120 mm
1048U125-I 1003mm x 1003mm, h 80mm B 125 260 030 u.r.1048U400-I 1003mm x 1003mm, h 80mm D 400 300 030 u.r.water-tight, 4 screws connecting frame and cover1048U-OE125-I 1003mm x 1003mm, h 80mm B 125 260 030 u.r.1048U-OE400-I 1003mm x 1003mm, h 80mm D 400 300 030 u.r.
Cast iron manhole top for special purposes Art. No. Description
e x f, h Class Price group € / piece
Non-slip square-textured surface and lifting grip Cover made from SGCI with hinge protection on the long side
Impermeable to surface water, with EPDM seal and 4 screws (M16 Allen screws with movably secured nuts).
Galvanised steel frame with hinge box and easy-to-loosen hinge bolts including pneumatic spring not projecting down-wards and galvanised steel scissor-type stay (open position 90°)
l special tops are custom-made (not on stock)
1-unit1047R400SCH-V 800mm x 600mm, h = dosrä D 400 030 u.r.1047S400SCH-V 1000mm x 600mm, h = dosrä D 400 030 u.r.1048Z400SCH-V 800mm x 800mm, h = dosrä D 400 030 u.r.1048U400SCH-V 1000mm x 1000mm, h = dosrä D 400 030 u.r.
2-unit2047R400SCH-V 800mm x 1200mm, h = dosrä D 400 030 u.r.2047S400SCH-V 1000mm x 1200mm, h = dosrä D 400 030 u.r.2048Z400SCH-V 800mm x 1600mm, h = dosrä D 400 030 u.r.2048U400SCH-V 1000mm x 2000mm, h = dosrä D 400 030 u.r.ä dosr = depending on structural requirements between 110 and 260 mm
NEW!
Manh
ole T
ops
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Cast iron cable duct cover (postal service), single-unitmanufactured to ÖN/EN 124, non-ventilatedModel V… screwed and imperme-able to surface water, surcharge upon request
Model -1 with vent
Pricegroup 030
Art. No. Description Class Weightkg
€ / piece
1048Y125-Mä 700mm x 700mm, h 100mm B 125 185 u.r.1048Y400-M 700mm x 700mm, h 100mm D 400 213 u.r.1048Y600-M 700mm x 700mm, h 100mm E 600 213 u.r.ä without cushioning
Cast iron manhole tops
Cast iron cable duct cover (postal service), 2-unitmanufactured to ÖN/EN 124, non-ventilatedModel V… screwed and impermeab-le to surface water, surcharge upon request
Model -1 with vent
Pricegroup 030
Art. No. Description Class Weightkg
€ / piece
2048Y125-Mä 1440mm x 700mm, h 100mm B 125 367 u.r.2048Y400-M 1440mm x 700mm, h 100mm D 400 425 u.r.2048Y600-M 1440mm x 700mm, h 100mm E 600 425 u.r.ä without cushioning
Cast iron cable duct cover, single-unitwith concrete fill, non-ventilated
Model -1 with vent
Pricegroup 030
Art. No. Description Class Weightkg
€ / piece
8048Y400-M 700mm x 700mm, h 100mm D 400 240 u.r.8048Y600-M 700mm x 700mm, h 100mm E 600 240 u.r.8048Y900-M 700mm x 700mm, h 100mm F 900 240 u.r.l can be supplied to special order!
Cast iron cable duct cover, 2-unitwith concrete fill, non-ventilated
Model -1 with vent
Pricegroup 030
Art. No. Description Class Weightkg
€ / piece
8049Y400-M 1440mm x 700mm, h 100mm D 400 460 u.r.8049Y600-M 1440mm x 700mm, h 100mm E 600 460 u.r.8049Y900-M 1440mm x 700mm, h 100mm F 900 460 u.r.l can be supplied only to customer’s specifications!
Cast iron manhole topÜA-certified, with PAT-hingeä
1-unit, square-shapedwithout lock
Pricegroup 030
Art. No. Description Class Weightkg
€ / piece
1062P-PAT-400-M 450mm x 450mm, h 210mm D 400 165 u.r.1062P-PAT-600-M 450mm x 450mm, h 210mm E 600 165 u.r.1062P-2PAT-400-M 600mm x 600mm, h 210mm D 400 269 u.r.1062P-3PAT-600-M 600mm x 600mm, h 210mm E 600 269 u.r.ä PATent hinge: cover and bolt replaceable without need to remove frame
Cast iron manhole topÜA-certified, with PAT-hingeä
1-unit, square-shapedwith lock
Pricegroup 030
Art. No. Description Class Weightkg
€ / piece
1062P-PAT-S-400M 450mm x 450mm, h 210mm D 400 158 u.r.1062P-PAT-S-600M 450mm x 450mm, h 210mm E 600 158 u.r.1062P-2PAT-S-400M 600mm x 600mm, h 210mm D 400 269 u.r.1062P-3PAT-S-600M 600mm x 600mm, h 210mm E 600 269 u.r.ä PATent hinge: cover and bolt replaceable without need to remove frame
Manh
ole T
ops
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Cast iron manhole tops
Cast iron manhole topsÜA-certified, with PAT-hingeä
1-unit, square-shaped
Pricegroup 030
Art. No. Description Class Weightkg
€ / piece
3063-400PAT 1000mm x 600mm, h 220mm D 400 394 u.r.3063-600PAT 1000mm x 600mm, h 220mm E 600 413 u.r.ä PATent hinge: cover and bolt replaceable without need to remove frame
Cast iron Coverdesigned to receive paving
Cover: cast ironfor pavers up to 8 cm high(for all frames with ID 50 mm)
Pricegroup 020
Art. No. Description Class Weightkg
€ / piece
non-ventilated
DE90400 DN 600, installation depth 50 mm D 400 41 u.r.
ventilated
DE90400-1 DN 600, installation depth 50 mm D 400 41 u.r.
matching frame, roundRA01000-50 GG, h = 100 mm D 400 30 u.r.
RA07000-50 Concrete/cast iron, h = 160mm D 400 89 u.r.
cast iron-Coverdesigned to receive paving conforming EN 124
Pricegroup 000
Cover: SGCIfor pavers up to 8 cm high, installation depth 60 mmFrame size: 710 x 800 mmFrame depth: 75 mm
Art. No. Description Class Weight kg
€ / piece
non-ventilatedE3RP060.060 600mm x 600mm D 400 98 u.r.
Top made of SGCIdesigned to receive paving
Cover: SGCIfor pavers up to 7 cm highincl. Frame
Pricegroup 130
Art. No. DN Class Weightkg
€ / piece
PM-91400-400 400 D 400 58 u.r.PM-91400-600 610 D 400 112 u.r.
Concrete/cast iron Coverwith sand bed
Cover: Concrete/cast iron, non-ven-tilatedFrame: cast iron
Pricegroup 020
Art. No. DN Class Weightkg
€ / piece
81125-500 500 B 125 39 u.r.
Concrete/cast iron Coverwith sand bed
Cover: Concrete/cast iron, non-ventilatedFrame: cast iron
Pricegroup 020
Art. No. DN Class Weightkg
€ / piece
81125-800 800 B 125 117 u.r.
Stee
l and
stain
less s
teel
Cove
rs
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Steel checker plate cover for use in buildings
Steel checker plate
suitable for light loads in private pedestrian areasnot approved for trafficked (public) areas
Price group 040
Art. No. Descriptione x f, h
Weightkg € / piece
1065A20-20 200mm x 200mm, h 30mm 2 u.r.1065A25-25 250mm x 250mm, h 30mm 3 u.r.1065A30-30 300mm x 300mm, h 30mm 4,5 u.r.1065A40-40 400mm x 400mm, h 30mm 7,5 u.r.1065A50-50 500mm x 500mm, h 30mm 10,5 u.r.1065A60-40 600mm x 400mm, h 30mm 9,5 u.r.l from 1065A-60-60 to be used only with reinforcement!
Riffelblechdeckel minium-coated, with simple lock
suitable for light loads in private pedestrian areasnot approved for trafficked (public) areas
Price group 040
Art. No. Descriptione x f, h
Weightkg € / piece
1065A-S20-20 200mm x 200mm, h 30mm 2 u.r.1065A-S25-25 250mm x 250mm, h 30mm 3 u.r.1065A-S30-30 300mm x 300mm, h 30mm 4,5 u.r.1065A-S40-40 400mm x 400mm, h 30mm 7,5 u.r.1065A-S50-50 500mm x 500mm, h 30mm 10,5 u.r.1065A-S60-40 600mm x 400mm, h 30mm 9,5 u.r.1065A-S60-60 600mm x 600mm, h 30mm 14,5 u.r.1065A-S80-60 800mm x 600mm, h 30mm 21 u.r.1065A-S80-80 800mm x 800mm, h 30mm 25 u.r.1065A-S100-60 1000mm x 600mm, h 30mm 26 u.r.1065A-S100-80 1000mm x 800mm, h 30mm 32 u.r.1065A-S100-100 1000mm x 1000mm, h 30mm 35 u.r.
Steel checker plate reinforced, minium-coated
no kN data
Price group 040
Art. No. Descriptione x f, h
Weightkg € / piece
1065A60-40-015 600mm x 400mm, h 30mm 12 u.r.1065A60-60-015 600mm x 600mm, h 30mm 16 u.r.1065A100-60-015 1000mm x 600mm, h 30mm 24 u.r.l galvanised upon request
Steel checker plate galvanised
suitable for light loads in private pedes-trian areasnot approved for trafficked (public) areas
Price group 040
Art. No. Descriptione x f, h
Weightkg € / piece
1065A-V20-20 200mm x 200mm, h 30mm 2 u.r.1065A-V25-25 250mm x 250mm, h 30mm 3 u.r.1065A-V30-30 300mm x 300mm, h 30mm 4,5 u.r.1065A-V40-40 400mm x 400mm, h 30mm 7,5 u.r.1065A-V50-50 500mm x 500mm, h 30mm 10,5 u.r.1065A-V60-40 600mm x 400mm, h 30mm 9,5 u.r.l from 1065A-V60-60 to be used only with reinforcement!
Stee
l and
stain
less s
teel
Cove
rs
�0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Steel checker plate cover for use in buildings, well covers
Steel checker plate galvanised, with simple lock
suitable for light loads in private pedestrian areasnot approved for trafficked (public) areas
Price group 040
Art. No. Descriptione x f, h
Weightkg € / piece
1065A-VS30-30 300mm x 300mm, h 30mm 4,5 u.r.1065A-VS40-40 400mm x 400mm, h 30mm 7,5 u.r.1065A-VS50-50 500mm x 500mm, h 30mm 10,5 u.r.1065A-VS60-40 600mm x 400mm, h 30mm 9,5 u.r.1065A-VS60-60 600mm x 600mm, h 30mm 14,5 u.r.1065A-VS80-60 800mm x 600mm, h 30mm 21 u.r.1065A-VS80-80 800mm x 800mm, h 30mm 25 u.r.1065A-VS100-60 1000mm x 600mm, h 30mm 26 u.r.1065A-VS100-100 1000mm x 1000mm, h 30mm 35 u.r.Price group 290KTSCH7 Key to lock u.r.
Steel checker plate reinforced, with rubber seal and screwed, minium-coated
suitable for light loads in private pedestrian areasnot approved for trafficked (public) areas
Price group 040
Art. No. Descriptione x f, h
Weightkg € / piece
1065C60-40-015 600mm x 400mm, h 30mm 12,5 u.r.1065C60-60-015 600mm x 600mm, h 30mm 18 u.r.1065C80-60-015 800mm x 600mm, h 30mm 23 u.r.1065C100-60-015 1000mm x 600mm, h 30mm 28 u.r.l galvanised upon request!
Well covers hot-dip galvanised, splash-proof
for pedestrian traffic, placed above ground level with rubber seal and hinge
Price group 040
Art. No. Descriptione x f, h
Weightkg € / piece
1065D-V-S40-40 400mm x 400mm, h 60mm 13 u.r.1065D-V-S60-40 600mm x 400mm, h 60mm 18 u.r.1065D-V-S60-60 600mm x 600mm, h 60mm 22 u.r.1065D-V-S80-80 800mm x 800mm, h 60mm 34 u.r.1065D-V-S10-10 1000mm x 1000mm, h 60mm 40 u.r.
Well covers hot-dip galvanised, splash-proof
for pedestrian traffic, placed above ground level with rubber seal and hinge
with additionally mounted vent capand insect screen
Price group 040
Art. No. Descriptione x f, h
Weightkg € / piece
1065DL-VS40-40 400mm x 400mm, h 60mm 16 u.r.1065DL-VS60-40 600mm x 400mm, h 60mm 21 u.r.1065DL-VS60-60 600mm x 600mm, h 60mm 25 u.r.1065DL-VS80-80 800mm x 800mm, h 60mm 37 u.r.1065DL-VS10-10 1000mm x 1000mm, h 60mm 45 u.r.
Well covers hot-dip galvanised, splash-proof
for pedestrian traffic, placed above ground level with rubber seal and hinge
Price group 040
Art. No. Description Weightkg € / piece
1065DL-VS600 DN 600, h 60mm 18 u.r.
Stee
l and
stain
less s
teel
Cove
rs
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Stainless steel manhole tops, accessories, tools and keysfor water meter or well shafts
Manhole top, stainless stell
Stainless steel model, cover made of 2 mm stainless steel plate 1.4301, with safety stay device to keep in open position and auto-locking me-chanism Frame made of Z-section with insect-proof rubber seal(frost and weather-resistant).
For easy opening the covers are fit-ted with a PNEUMATIC SPRING.
Price group 046
Art. No. Clear Opening mm Weight kg € / pieceStandard model166G-ED 600 x 600 20 u.r.188G-ED 800 x 800 28 u.r.111G-ED 1000 x 1000 38 u.r.
Standard model with additional air dome DN 150 welded on,with stainless steel screen166GD-ED 600 x 600 24 u.r.188GD-ED 800 x 800 32 u.r.111GD-ED 1000 x 1000 42 u.r.
Standard model with additional polyurethane foam insulation,bottom protected by stainless steel plate with air dome and insulation166I-ED 600 x 600 32 u.r.188I-ED 800 x 800 44 u.r.111I-ED 1000 x 1000 67 u.r.
with air dome and insulating166ID-ED 600 x 600 37 u.r.188ID-ED 800 x 800 49 u.r.111ID-ED 1000 x 1000 72 u.r.l Round covers available against surcharge
Cushioning inserts (anti-clatter rings)
Price group 020
Art. No. Installation depth, colour Ø (mm) € / piece
ANTI-KLAP-682 50 mm, black 675 u.r.ANTI-KLAP-L647 18 mm, greenä 647 u.r.ANTI-KLAP-L675 50 mm, greenä 675 u.r.Two-component liquid plastic:ANTI-KLAP-2K-M 220 ml u.r.ANTI-KLAP-2KOMP 440 ml u.r.ä with ribs
Key to manhole tops
Price group 030
Art. No. # Description Weight kg € / piece
SCHL1 u 1 u.r.SCHL2 w triangular SW 16mm 0,6 u.r.SCHL3 w triangular SW 18mm 0,6 u.r.
SCHL4 vmale square SW 18/22mm
Allen key, hexagonal SW 17mm0,6 u.r.
SCHL5 - square SW 16mm 0,6 u.r.SCHL6 - square SW 18mm 0,6 u.r.
Price group 421
Titanium-aluminium cover lifter easy to adjust to various topsLIFTERPermits levelling of completecovers with 2 lifters (placed opposite)
Art. No. Description Weight kg € / piece
DE-HEBER Alu-Titan 850 mm 3,0 u.r.
u v w
Safe
ty E
quip
men
t
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
High-performance safety equipment
Basic Set Athlet P Art. No. Pieces Description € / piece
45864 1 Athlet P 500kg hoist with removable disk u.r.4503 1 cable with pretensioning spring 10m u.r.
23948 1MARTIN HRSG
(height safety and rescue device)cable 5-20m
u.r.
23564 1 Case for HRSG u.r.17079 1 Aluminium quick-action safety barriers u.r.18164 1 Traffic sign u.r.Athlet-GP1 1 Set price u.r.
Basic Set
Personal Safety Set Art. No. Pieces Description € / piece
47683 2 PN 42 click - harness u.r.50528 1 Safety vest (sizes XS - XXXL) u.r.50663 1 Sling Set u.r.11836 1 Helmet u.r.40233 2 Carabiner PN-112 u.r.Athlet-EPS1 1 Set price u.r.
Personal safety, lifting and rescuing
Canalization Set Art. No. Pieces Description € / piece
47683 1 PN 42 click - harness u.r.
18086 2 Rescue pants, oil- and grease resistant, shoe size 45(also available for shoe size 39-44)
u.r.
11836 3 Helmet u.r.40233 1 Carabiner PN-112 u.r.Athlet-KPS1 1 Set price u.r.
NEW!
NEW!
Safe
ty E
quip
men
t
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
DSD Digital Speed Display Art. No. Description € / piece
DCDSD
DSD Digital Speed Display with patented SAFETY-Func-tion, deigned to inform drivers and their social environment about their speed behaviour and to put social pressure on
them if needed, to reduce their driving speed.u.r.
NEW!
Load lifting set Art. No. Pieces Description € / piece
4062 1 Toolbox u.r.4384 2 Adaptor SP039 u.r.1826 2 Two-hand gripper SP024 u.r.1364 2 T-hook S004 u.r.1363 2 Round hook u.r.4595 1 4-fold suspension gear u.r.18289 2 angular hook adaptor u.r.Athlet-LHP1 1 Set price u.r.
Personal safety, lifting and rescuing
Safety equipment, site-traffic securing
Pump lifting extension set Art. No. Pieces Description € / piece
16323 1 Extra load hook for pumps u.r.17347 1 Gripper for pumps up to 1,2 tons u.r.42435 1 Gripper for large pumps u.r.Athlet-LHP1 1 Set price u.r.
Heavy load bar set Art. No. Pieces Description € / piece
4104 1 Combi bar 1222 mm u.r.1354 2 Adaptor with screw nut u.r.1743 2 Adaptor SP014 u.r.5391 2 Head-Adaptor 26/14 u.r.Athlet-SLBP1 1 Set price u.r.
Site-traffic securing, traffic census
SDR Side radar traffic classifier Art. No. Description € / piece
DCSDRSDR traffic classifier was designed to meet the increa-sing demand for a solid and reliable non intrusive traffic
measuring device.u.r.
NEW!
Alup
ura®
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Aluminium manhole topssuitable for use in buildings
Manhole Tops for pedestrian traffic with ALU checker plate top Art. No. Description
e x f, hWeight
(kg) € / piece
impermeable to surface water, scre-wed, with sealPrice group 043
1065C-ALU60-40 600mm x 400mm, h 36mm 5,2 u.r.1065C-ALU60-60 600mm x 600mm, h 36mm 7,3 u.r.1065C-ALU100-60 1000mm x 600mm, h 36mm 10,9 u.r.
1065C-DI seal per meter u.r.
Recessed cover with reinforcementfor optional surfaces, screwed Art. No. Description
e x f, hWeight
(kg) € / piece
ALUPURA®
impermeable to surface water, with sealPrice group 043
Note instructions for installationl Row tops upon request
1065BV-ALU30-30ä 300mm x 300mm, h 75mm 4,6 u.r.1065BV-ALU40-40ä 400mm x 400mm, h 75mm 5,8 u.r.1065BV-ALU45-45ä 450mm x 450mm, h 75mm 6,5 u.r.1065BV-ALU50-50ä 500mm x 500mm, h 75mm 7,1 u.r.1065BV-ALU60-40ä 600mm x 400mm, h 75mm 7,1 u.r.1065BV-ALU60-60ä 600mm x 600mm, h 75mm 9 u.r.1065BV-ALU60-90 900mm x 600mm, h 75mm 11,5 u.r.1065BV-ALU70-70 700mm x 700mm, h 75mm 10,6 u.r.1065BV-ALU80-60 800mm x 600mm, h 75mm 10,5 u.r.1065BV-ALU80-80 800mm x 800mm, h 75mm 12,5 u.r.1065BV-ALU10-60 1000mm x 600mm, h 75mm 12,5 u.r.1065BV-ALU10-80 1000mm x 800mm, h 75mm 13 u.r.1065BV-ALU10-10 1000mm x 1000mm, h 75mm 14,5 u.r.ä Recessed tops for Class B 125 kN upon requestl Designed to withstand test load after complete filling with concrete, conforming to EN 206 Type C 30/37
Spares Art. No. Description € / piece
no image
1065B-ALU-SCHG Lifting key (order two pcs.) u.r.1065BV-ALU-DI-G Seal per metre u.r.1065BV-ALUSCHRG Allen screw u.r.1065BV-ALU-STL Plastic dust strip per meter u.r.NEW!
Recessed cover with flangefor tight fit Art. No. Description
e x f, hWeight
(kg) € / piece
ALUPURA®
with seal
Price group 043
1065BV-ALU-F144 400mm x 400mm, h 75mm, 30mm Flansch 7,0 302,901065BV-ALU-F166 600mm x 600mm, h 75mm, 30mm Flansch 10,5 357,501065BV-ALU-F188 800mm x 800mm, h 75mm, 30mm Flansch 14,3 475,201065BV-ALU-F244 400mm x 400mm, h 75mm, 80mm Flansch 7,8 307,801065BV-ALU-F266 600mm x 600mm, h 75mm, 80mm Flansch 11,2 361,801065BV-ALU-F288 800mm x 800mm, h 75mm, 80mm Flansch 15,8 480,60l Flanschanbindung 22 mm unter Niveau
Recessed cover backflow-prooftightly welded, factory-checked for tightness Art. No. Description
e x f, hWeight
(kg) € / piece
ALUPURA®
with seal
Price group 043
1065BV-ALU-RS33 300mm x 300mm, h 75mm 4,9 422,301065BV-ALU-RS44 400mm x 400mm, h 75mm 6,1 452,501065BV-ALU-RS45 450mm x 450mm, h 75mm 6,8 473,-1065BV-ALU-RS55 500mm x 500mm, h 75mm 7,5 494,601065BV-ALU-RS64 600mm x 400mm, h 75mm 7,5 494,601065BV-ALU-RS66 600mm x 600mm, h 75mm 9,5 548,60l up to 0,5 bar, Note instructions for installation!
NEW!
NEW!
Rece
ssed
cove
rs
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Recessed steel tops, hot-dip galvanised, stainless steel 1.4301
Recessed steel tops,hot-dip galvanised. Reinforced recessed tops(infill cover)
Art. No. Descriptione x f, h
up to Class ä
Weight (kg) € / piece
impermeable to surface waterdepth of recessed tops 52 mm
Price group 040
1065BV125-33K 300mm x 300mm, h 75mm B 125 10 u.r.1065BV125-45K 450mm x 450mm, h 75mm B 125 16 u.r.1065BV125-55K 500mm x 500mm, h 75mm B 125 17 u.r.1065BV125-64K 600mm x 400mm, h 75mm B 125 17 u.r.1065BV125-66K 600mm x 600mm, h 75mm B 125 21 u.r.1065BV125-86K 800mm x 600mm, h 75mm B 125 27 u.r.1065BV125-88K 800mm x 800mm, h 75mm B 125 31 u.r.1065BV125-106K 1000mm x 600mm, h 75mm B 125 31 u.r.1065BV125-108K 1000mm x 800mm, h 75mm B 125 37 u.r.1065BV125-110K 1000mm x 1000mm, h 75mm B 125 42 u.r.1065BV125SCHL key set for BV, BVE, BVGD 1 u.r.ä Test load is obtained by complete filling with concrete to EN 206 Type C 30/37
Recessed steel tops,hot-dip galvanised. Reinforced recessed tops(infill cover)
Art. No. Descriptione x f, h
up to Class ä
Weight (kg) € / piece
impermeable to surface water
Price group 040
depth of recessed top 102 mm1065BVH-MAXI66 600mm x 600mm, h 125 mm B 125 28 u.r.1065BVH-MAXI88 800mm x 800mm, h 125 mm B 125 34 u.r.Trafficable by passenger cars, without seal, depth of recessed top 96 mm1065BH-MAXI600 DN 600, h 100 mm B 125 27 u.r.ä Test load is obtained by complete filling with concrete to EN 206 Type C 30/37
Recessed stainless steel tops,smell and water proof, reinforced recessed tops for optional fillings
Art. No. Descriptione x f, h
up to Class ä
Weight (kg) € / piece
Price group 040
1065BVE33K 300mm x 300mm, h 75mm B 125 6 u.r.1065BVE44K 400mm x 400mm, h 75mm B 125 13 u.r.1065BVE55K 500mm x 500mm, h 75mm B 125 18 u.r.1065BVE64K 600mm x 400mm, h 75mm B 125 16 u.r.1065BVE66K 600mm x 600mm, h 75mm B 125 21 u.r.1065BVE88K 800mm x 800mm, h 75mm B 125 30 u.r.ä Test load is obtained by complete filling with concrete to EN 206 Type C 30/37
Parts for 1065BVE Art. No. Description € / piece
Price group 040 no image1065EV-GRIFFE-L Lifting handles u.r.1065E-ABDK Cover panel u.r.
Rece
ssed
cove
rs
�6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Recessed steel tops, hot-dip galvanised, stainless steel 1.4301
Recessed steel tops,hot-dip galvanised. Reinforced recessed tops(infill cover)
Art. No. Descriptione x f, h
up to Class ä
Weight (kg) € / piece
impermeable to surface waterdepth of recessed tops 52 mm
Price group 040
like Type 1065BV but with reinforced recessed top1065BVS250-66 600mm x 600mm, h 75mm C 250 21 u.r.1065BVS250-88 800mm x 800mm, h 75mm C 250 31 u.r.1065BVS250-106 1000mm x 600mm, h 75mm C 250 31 u.r.1065BVS250-110 1000mm x 1000mm, h 75mm C 250 42 u.r.ä Test load is obtained by complete filling with concrete to EN 206 Type C 30/37
Recessed steel tops,hot-dip galvanised. Reinforced recessed tops(infill cover)
Art. No. Descriptione x f, h
up to Class ä
Weight (kg) € / piece
impermeable to surface waterdepth of recessed tops 52 mm
Price group 040
like Type 1065BVS250 but with reinforced recessed top1065BVS400-66 600mm x 600mm, h 75mm D 400 21 u.r.1065BVS400-88 800mm x 800mm, h 75mm D 400 31 u.r.1065BVS400-110 1000mm x 1000mm, h 75mm D 400 42 u.r.ä Test load is obtained by complete filling with concrete to EN 206 Type C 30/37
Recessed steel tops,hot-dip galvanised. Reinforced recessed tops(infill cover)
Art. No. Descriptione x f, h
up to Class ä
Weight (kg) € / piece
impermeable to surface waterdepth of recessed tops 52 mm
Price group 040
made from steel, hot-dip galvanised1065BV-GD66 600mm x 600mm, h 75mm B 125 21 u.r.1065BV-GD86 800mm x 600mm, h 75mm B 125 27 u.r.1065BV-GD88 800mm x 800mm, h 75mm B 125 31 u.r.1065BV-GD106 1000mm x 600mm, h 75mm B 125 30 u.r.1065BV-GD110 1000mm x 1000mm, h 75mm B 125 42 u.r.ä Test load is obtained by complete filling with concrete to EN 206 Type C 30/37
Recessed stainless steel tops,Reinforced recessed tops (infill cover) Art. No. Description
e x f, hup to
Class äWeight
(kg) € / piece
impermeable to surface waterdepth of recessed tops 52 mm
Price group 040
made from stainless steel1065BVE-GD66 600mm x 600mm, h 75mm B 125 21 u.r.1065BVE-GD86 800mm x 600mm, h 75mm B 125 27 u.r.1065BVE-GD88 800mm x 800mm, h 75mm B 125 31 u.r.1065BVE-GD106 1000mm x 600mm, h 75mm B 125 30 u.r.1065BVE-GD110 1000mm x 1000mm, h 75mm B 125 42 u.r.ä Test load is obtained by complete filling with concrete to EN 206 Type C 30/37
Gully
gra
tes a
nd to
ps
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Gully grate DN 600
Type 31000manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg) € / piece
CI frame round
Price group 051
31015 610 mm / 70 mm / 18 mm A 15 50 u.r.31125 610 mm / 70 mm / 18 mm B 125 55 u.r.31250 610 mm / 70 mm / 18 mm C 250 60 u.r.31400 610 mm / 100 mm / 50 mm D 400 110 u.r.31400D as above, with cushioning insert D 400 110 u.r.
Type 32000manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg) € / piece
CI frame with square-shaped base plate
Price group 051
32015 610 mm / 70 mm / 18 mm A 15 55 u.r.32125 610 mm / 70 mm / 18 mm B 125 60 u.r.32250 610 mm / 70 mm / 18 mm C 250 65 u.r.32400 610 mm / 100 mm / 50 mm D 400 110 u.r.32400D as above, with cushioning insert D 400 110 u.r.
Type 37000manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg) € / piece
Concrete/CI frame round
Price group 051
37015 610 mm / 130 mm / 18 mm A 15 85 u.r.37125 610 mm / 130 mm / 18 mm B 125 90 u.r.37250 610 mm / 130 mm / 18 mm C 250 95 u.r.37400 610 mm / 160 mm / 50 mm D 400 150 u.r.37400D as above, with cushioning insert D 400 150 u.r.
Type 38000manufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
Clear Opening/Frame Depth/Installation Depth Class Weight (kg) € / piece
Concrete/CI frame square-shaped
Price group 051
38015 610 mm / 130 mm / 18 mm A 15 130 u.r.38125 610 mm / 130 mm / 18 mm B 125 135 u.r.38250 610 mm / 130 mm / 18 mm C 250 140 u.r.38400 610 mm / 160 mm / 50 mm D 400 210 u.r.38400D as above, with cushioning insert D 400 210 u.r.
Gully
gra
tes a
nd to
ps
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
SGCI Gully grate DN 600
Type Paysagemanufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description Class Weight
(kg) € / piece
SGCI grating and frame for use on kerbs and premises
with cushioning insert
Price group 130
round framePM-31250D DN 600, h 75 mm C 250 55 u.r.frame with square-shaped base plate (no image)PM-32250D DN 600, h 75 mm C 250 62 u.r.
Type Rexelmanufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description Class Weight
(kg) € / piece
SGCI grating and frame for urban traffic and in traffic-calmed areas with hinge and auto-locking mechanism
with cushioning insert
Price group 130
round framePM-31400VD DN 600, h 100 mm D 400 57 u.r.frame with square-shaped base plate (no image)PM-32400VD DN 600, h 100 mm D 400 66 u.r.
Type Pamrexmanufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description Class Weight
(kg) € / piece
SGCI grating and frame for heavily trafficked roads with hinge (lockable at 90°)
with cushioning insert
Price group 130
round framePM-31400D DN 600, h 100 mm D 400 91 u.r.frame with square-shaped base plate (no image)PM-32400D DN 600, h 100 mm D 400 100 u.r.
Gully
gra
tes a
nd to
ps
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Tops (gully grates) for road surface run-off
Type 44000manufactured to ÖN/EN 124 and ÖN B5110, Clear Opening DN 450
Art. No. Descriptionc x c, h Class Weight
(kg) € / piece
Tops (gully grates) for street inlets with inte-grated bucket holderGrating: CIclatter-free due to inclined base
Price group 050
flat form44250P 560 x 560, h 180 mm C 250 108 u.r.44400P 560 x 560, h 180 mm D 400 114 u.r.
concave form, not approved for carriageways44250R 560 x 560, h 180 mm C 250 106 u.r.44400R 560 x 560, h 180 mm D 400 115 u.r.
Type VIATOP-Topmanufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description
c x c, h Class Weight (kg) € / piece
SGCI grating and frame with hingeclatter-free due to spring bar locking mechanism,safe for cyclists, anti-slip, with bucket holderNEW DESIGN:Safe for wheel-chairs and bicycles
Price group 130
flat formPM-43250P55 482 x 485, h 102 mm C 250 44 u.r.PM-43400P55 482 x 485, h 102 mm D 400 52 u.r.concave formPM-43250R55 482 x 485, h 127 mm C 250 48 u.r.PM-43400R55 482 x 485, h 127 mm D 400 52 u.r.
Type DEDRAmanufactured to ÖN/EN 124 and ÖN B5110 Art. No. # Description
c x d, h Class Weight (kg) € / piece
SGCI grating and frame with hingelockable,Clear Opening 600 x 600
Price group 130
Flange on three sidesPM-43400P66-3 u 714 x 800, h 101 mm D 400 85 u.r.
Flange on four sidesPM-43400P66-4 v 800 x 800, h 101 mm D 400 88 u.r.
u
v
Gully
gra
tes a
nd to
ps
�0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
SGCI gully grate
Type Viatop-Topmanufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description Class Weight
(kg) € / piece
SGCI grating and frame for clear opening 300 x 500 with integrated bucket holder
Price group 130
flat formPM-43250P35 520 x 307, h 102 mm C 250 33 u.r.PM-43400P35 520 x 307, h 102 mm D 400 36 u.r.concave formPM-43250R35 520 x 307, h 102 mm C 250 37 u.r.PM-43400R35 520 x 307, h 102 mm D 400 40 u.r.
Type Squadra-Austriamanufactured to ÖN/EN 124 and ÖN B5110 Art. No. Description Class Weight
(kg) € / piece
SGCI grating and frame for street inletsDN 450 with spring bar locking mechanism and bucket holder
Price group 130
flat formPM-43250P-AUT 500 x 530, h 100 mm C 250 35,5 u.r.
Type Squadramanufactured to EN 124 Art. No. Description Class Weight
(kg) € / piece
SGCI grating and frame with spring bar locking mechanism
Price group 130
flat formPM-SQU250P a 250, h 40 mm C 250 15,3 u.r.PM-SQU300P a 300, h 40 mm C 250 20,1 u.r.PM-SQU400P a 400, h 40 mm C 250 27,5 u.r.PM-SQU500P a 500, h 40 mm C 250 42,0 u.r.PM-SQU600P a 600, h 40 mm C 250 60,0 u.r.PM-SQU700P a 700, h 40 mm C 250 77,0 u.r.
Type Victoriamanufactured to EN 124 Art. No. Description Class Weight
(kg) € / piece
SGCI grating and frame with hinge and and three-point support
Price group 130
flat formPM-VIC250P 400 mm x 445 mm x 75 mm C 250 34 u.r.PM-VIC400P 400 mm x 445 mm x 100 mm D 400 41 u.r.
Gully
gra
tes a
nd to
ps
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Tops for yard gullies
Gully top conforming to EN 1253CI, round, without basket holder Art. No. Description Class Weight
(kg) € / piece
Price group 06021015 DN 330, h 25 mm L 15 9 u.r.21050 DN 330, h 25 mm L 50 12 u.r.
Gully top conforming to EN 1253CI, flat, square-shaped, basket holder integrated
Art. No. Description Class Weight (kg) € / piece
Price group 06061015P DN 300, h 60 mm L 15 13 u.r.61125P DN 300, h 100 mm M 125 20 u.r.
Gully top conforming to EN 1253CI, concave, square-shaped, without basket holder
Art. No. Description Class Weight (kg) € / piece
Price group 06061015R DN 300, h 100 mm L 15 17 u.r.61125R DN 300, h 100 mm M 125 23 u.r.
Gully top conforming to EN 1253concrete/CI, flat, square-shaped, basket holder integrated
Art. No. Description Class Weight (kg) € / piece
Price group 06068015P DN 300, h 80 mm L 15 33,5 u.r.68125P DN 300, h 130 mm M 125 50,0 u.r.
Gully top conforming to EN 1253concrete/CI, flat, square-shaped, basket holder integrated
Art. No. Description Class Weight (kg) € / piece
Price group 06068250P DN 300, h 150 mm M 250 50 u.r.
Gully
gra
tes a
nd to
ps
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Gully grates with square-shaped openings
Gully grate 1001MRsquare, CI, with frame Art. No. Description Class Weight
(kg) € / piece
Price group 0601001MR200 a 200 mm, h 20 mm 50 kN 3,5 u.r.1001MR250 a 250 mm, h 20 mm 50 kN 4,5 u.r.1001MR300 a 300 mm, h 27 mm 50 kN 8,0 u.r.1001MR350 a 350 mm, h 27 mm 50 kN 12,0 u.r.1001MR400 a 400 mm, h 30 mm 50 kN 15,0 u.r.1001MR450 a 450 mm, h 40 mm 50 kN 22,0 u.r.1001MR500 a 500 mm, h 42 mm 50 kN 34,0 u.r.1001MR600 a 600 mm, h 42 mm 50 kN 43,0 u.r.
Gully grate 1001MRsqare, aus SGCI, with frame Art. No. Description Class Weight
(kg) € / piece
Price group 0601001MR400SG a 400 mm, h 30 mm B 125 10,0 u.r.1001MR450SG a 450 mm, h 40 mm B 125 16,0 u.r.1001MR500SG a 500 mm, h 42 mm B 125 21,0 u.r.1001MR600SG a 600 mm, h 42 mm B 125 32,0 u.r.
Gully grate 1001Csquare, CI, with frame Art. No. Description Class Weight
(kg) € / piece
Price group 0601001C400 a 410 mm, h 50 mm C 250 34,0 u.r.1001C500 a 500 mm, h 65 mm C 250 48,0 u.r.1001C600 a 600 mm, h 70 mm C 250 75,0 u.r.
Gully grate 1001Csqare, aus SGCI, with frame Art. No. Description Class Weight
(kg) € / piece
Price group 0601001C400SG a 410 mm, h 50 mm D 400 34,0 u.r.1001C500SG a 500 mm, h 65 mm D 400 48,0 u.r.1001C600SG a 600 mm, h 70 mm D 400 75,0 u.r.
Gully grate 1006square, CI, with frame, concave Art. No. Description Class Weight
(kg) € / piece
Price group 0601006E1 a 300 mm, h 105 mm B 125 33,0 u.r.1006F1 a 400 mm, h 110 mm 50 kN 39,0 u.r.
Gully
gra
tes a
nd to
ps
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Gully grates made from cast iron
Gully grate „Tunnel“SGCI, flat, clatter-free due to two inclined bases, hook-in domed trap cover quenches flammable light liquids
Art. No. a x bmm
c x dmm
hmm Class Weight
(kg) € / piece
Price group 0501005C-TU 600 x 600 770 x 810 120 F 900 270 u.r.complete domed trap cover DN 1501005C-SIF - 78 u.r.
Gully grate for mountain roads „Total“with extra-high intake capacity, e.g. in downhill roads. Note direction of flow!
Art. No. Clear Openingmm
hmm Class Weight
(kg) € / piece
Price group 0501005TO250 450 70 C 250 45 u.r.1005TO400N* 450 100 D 400 68 u.r.1005STR(STREET) 444 125 D 400 82 u.r.* not applicable for dynamic load szenario
Gully grate „HIGHWAY“only for installation on edge of carriageway! Art. No. Clear Opening
mmh
mm Class Weight (kg) € / piece
Price group 0501005HI 500 x 500 160 D 400 115 u.r.
1005HI-SR 500 x 500, 4 screws 160 D 400 115 u.r.1005HI-SCH-600 500 x 500, with lock 130 E 600 95 u.r.l For pedestrian precincts available with narrow slots of 16 mmSCHL6 key to lock - - u.r.
Gully
gra
tes a
nd to
ps
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Regional gully grates, special models
Model Graz 1 with lengthwise slots Art. No. h1/h2 Exposed frame surface mm Class Weight
(kg) € / piece
Clear Opening300 x 500
Price group 050
1011N-N250-M 100/80 525 x 329 C 250 51 u.r.1011N-H250-M 150/130 525 x 329 C 250 65 u.r.1011N-N400-M 100/80 525 x 329 D 400 51 u.r.1011N-H400-M 150/130 525 x 329 D 400 65 u.r.l All gully grates Graz 1 and Graz 2 are mutually exchangeable (same frame)
h1 h2
Model Graz 2 with crosswise slots Art. No. h1/h2 Exposed frame surface mm Class Weight
(kg) € / piece
Clear Opening300 x 500
Price group 050
1011Q-N250-M 100/80 525 x 329 C 250 53 u.r.1011Q-H250-M 150/130 525 x 329 C 250 67 u.r.1011Q-N400-M 100/80 525 x 329 D 400 53 u.r.1011Q-H400-M 150/130 525 x 329 D 400 67 u.r.l All gully grates Graz 1 and Graz 2 are mutually exchangeable (same frame)
h1 h2
Model Styria Art. No. h Exposed frame surface mm Class Weight
(kg) € / piece
Clear Opening500 x 500 and600 x 600
Price group 050
concave1012C-M 100 527 x 527 C 250 80 u.r.1012D-M 100 627 x 627 C 250 105 u.r.1012C-M-400 100 527 x 527 D 400 78 u.r.1012D-M-400 100 627 x 627 D 400 110 u.r.flat1012C-G-M 100 527 x 527 C 250 78 u.r.1012D-G-M 100 627 x 627 C 250 110 u.r.1012C-G-M-400 100 527 x 527 D 400 78 u.r.1012D-G-M-400 100 627 x 627 D 400 110 u.r.
Gully
gra
tes a
nd to
ps
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CI gully grate with PAT hinge
CI street gully grate Art. No. Clear opening, heightmm Class Weight
(kg) € / piece
with PAT hinge
Price group 0501005B
without integrated lock1005B2-PAT-400 600 mm, h 210 mm D 400 234 u.r.1005B3-PAT-600 600 mm, h 210 mm E 600 260 u.r.with integrated lock1005B2-PAT-S400 600 mm, h 210 mm D 400 234 u.r.1005B3-PAT-S600 600 mm, h 210 mm E 600 260 u.r.l PATent hinge: Top and bolt replaceable without need to remove frame!
Model for pedestrian precinctsSpecial model for pedestrian precinct with smaller desired inlet cross-section for pedestrian area
Art. No. Clear opening, heightmm Class Weight
(kg) € / piece
with PAT hinge
Price group 050
1005F with textured grid design, without lock1005F-PAT-400 450 mm, h 210 mm D 400 139 u.r.with textured grid design, with lock1005F-PAT-S400 450 mm, h 210 mm D 400 139 u.r.l PATent hinge: Top and bolt replaceable without need to remove frame!
CI street gully grate Art. No. Clear opening, heightmm Class Weight
(kg) € / piece
with PAT hinge
Price group 0501005P
flat without lock1005P-PAT-400 450 mm, h 210 mm D 400 139 u.r.1005P-PAT-S400 450 mm, h 210 mm D 400 139 u.r.flat with lock1005P-PAT-600 450 mm, h 210 mm E 600 139 u.r.1005P-PAT-S600 450 mm, h 210 mm E 600 139 u.r.l PATent hinge: Top and bolt replaceable without need to remove frame!
CI street gully grate Art. No. Clear opening, heightmm Class Weight
(kg) € / piece
with PAT hinge
Price group 050 1005R
concave without lock1005R-PAT-300 300 mm, h 170 mm D 400 60 u.r.1005R-PAT-400 450 mm, h 210 mm D 400 139 u.r.1005R-PAT-600 450 mm, h 210 mm E 600 139 u.r.concave with lock1005R-PAT-S400 450 mm, h 210 mm D 400 139 u.r.1005R-PAT-S600 450 mm, h 210 mm E 600 139 u.r.l PATent hinge: Top and bolt replaceable without need to remove frame!
Kerb
gul
lys
�6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CI/SGCI kerb gullies
Kerb gullies square-shaped, Water inlet either on the straight or the chamfered face
Art. No. Description Class Weight (kg) € / piece
Price group 50
905G450 a 440 mm, h 170 mm A 50 59 u.r.905S450 a 440 mm, h 170 mm A 50 59 u.r.905G600 a 570 mm, h 170 mm A 50 88 u.r.905S600 a 570 mm, h 170 mm A 50 88 u.r.915G450 a 440 mm, h 170 mm B 125 63 u.r.915S450 a 440 mm, h 170 mm B 125 63 u.r.with hinge and 14 mm facet925G450SPH-F a 440 mm, h 170 mm C 250 61 u.r.925G450-650SPH 450 mm x 650 mm, h 210 mm C 250 111 u.r.925VLBG-G 550 mm x 530 mm C 250 61 u.r.925VLBG-S 550 mm x 530 mm C 250 61 u.r.l Lock upon request
SGCI kerb gullies Art. No. Description Class Weight (kg) € / piece
Price group 130
Type T with coverPM-925T120 DN 610, h 120 mm C250 72 u.r.PM-925T200 DN 610, h 200 mm C250 78 u.r.Type Selecta - 500with grating, lid with hinges, and automatic locking mechanismPM-925SEL125 a 385 mm, h 125 mm C 250 55 u.r.PM-925SEL205 a 385 mm, h 205 mm C 250 57 u.r.Type Selecta - Maxiwith grating, lid with hinges, and automatic locking mechanism,level-adjusting lidPM-925MAXI-N 540 x 450 x 135-155 C 250 92 u.r.PM-925MAXI-H 540 x 450 x 175-225 C 250 94 u.r.
Solid concrete with CI ringand frame in seating area Art. No. Description Class Weight
(kg) € / piece
Price group 50
8317 Clear Opening 440 mm, h 260 mm B 125 137 u.r.
Brid
ge d
rain
age s
yste
ms
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.
CI Bridge drainage systems „WAL-AUSTRIA“according RVS 15.43
Bridge drainage system, Class D 400, extendable Price group 060
Art. No. Description Class Weight(kg) € / piece
SpoutWAL332 Drains vertically, DN 150, flat D 400 34 u.r.WAL333 Drains laterally 3 ° DN 100 D 400 37 u.r.WAL334 Drains vertically DN 150 D 400 37 u.r.Base frame with compression-moulded flangeWAL335G h 50 mm D 400 26 u.r.WAL335-60 h 60 mm D 400 26 u.r.WAL335H-70 h 70 mm D 400 31 u.r.WAL335A-80 h 80 mm D 400 34 u.r.WAL335B-90 h 90 mm D 400 35 u.r.WAL335C-100 h 100 mm D 400 38 u.r.WAL335D-110 h 110 mm D 400 40 u.r.WAL335E-120 h 120 mm D 400 42 u.r.WAL335E-130 h 120 mm D 400 44 u.r.WAL335E-140 h 120 mm D 400 46 u.r.WAL335E-150 h 120 mm D 400 48 u.r.Extension frameWAL336B-50 inst. depth 25 mm, h 50 mm D 400 15 u.r.WAL336A-70 h 70 mm D 400 20 u.r.WAL336-100 h 100 mm D 400 34 u.r.WAL337-140 h 140 mm D 400 46 u.r.WAL338-160 h 160 mm D 400 53 u.r.Gully gridsWAL339-400 inlet cross section: 350 cm², h 54 mm D 400 25 u.r.WAL339-600 inlet cross section: 350 cm², h 54 mm E 600 25 u.r.WAL340-400 inlet cross section: 350 cm², h 54 mm D 400 25 u.r.WAL340-600 inlet cross section: 350 cm², h 54 mm E 600 25 u.r.WAL341-400 ics: 430 cm², only for WAL336B, h=25 mm D 400 25 u.r.
Set of screws for base frame Price group 060
Art. No. Description € / SetWAL-VERSCHR070N Set (2 pcs.) L 70 mm u.r.for extension up to WAL336WAL-VERSCHR170N Set. (2 pcs.) L 170 mm u.r.for extension up to WAL338WAL-VERSCHR230N Set (2 pcs.) L 230 mm u.r.PE pipe with shrink sleeve and sealing ringWAL-PEKR160-1 L 1000 mm u.r.WAL-PEKR160-1,5 L 1500 mm u.r.WAL-PEKR160-2 L 2000 mm u.r.Interlayers + dirt pansWAL1 Set (4 pcs.), h 10 mm u.r.WAL2 Set (4 pcs.), h 20 mm u.r.WAL-SFE dirt pants made from stainless steel u.r.
WAL334
Brid
ge d
rain
age s
yste
ms
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Cast iron insulating drainage
Insulation and drainage
CI - parts tarred (T) or galvanised (G) or stainless steel (SS)
1 set consists of:
(SIDE...) CI cover(SITR...) PVC funnel(SIRO...) PVC pipe, length = 500 mm(SIKO...) PVC cone (optional for newly constructed bridges)
Insulation drainage Price group 060
Art. No. Description Weight(kg) € / piece
SI352GT-N CI - parts tarred DN/da/ 36/50 2 u.r.SI352V-N CI - parts galvanised DN/da/ 36/50 2 u.r.
SI350GT-N tarred DN/da/ 45/70 8 u.r.SI350V-N galvanised DN/da 45/70 8 u.r.
SI352GT-S tarred DN/da/ 36/50 2 u.r.SI352V-S galvanised DN/da 36/50 2 u.r.
SI353GT-S tarred DN/da/ 53/60 7 u.r.SI353V-S galvanised DN/da 53/60 7 u.r.
SI300GT-S tarred DN/da/ 55/70 8 u.r.SI300V-S galvanised DN/da 55/70 8 u.r.
SI350GT-S tarred DN/da/ 45/70 8 u.r.SI350V-S galvanised DN/da 45/70 8 u.r.SI300E-S stainless steel 1.4301 DN 70 3,3 u.r.SI300-V4A-S stainless steel 1.4571 DN 70 3,3 u.r.
SI354GT-S tarred DN/da/ 90/100 11 u.r.SI354V-S galvanised DN/da 90/100 11 u.r.
Top with lateral discharge opening DN 150 Price group 060
Art. No. Description Class € / piece1007-250 a 300 mm, h 70 mm C 250 u.r.with lock1007-250S a 300 mm, h 70 mm C 250 u.r.ET1007 hook in funnel - u.r.KTSCH8 key to lock - u.r.
For newly constructed bridges
Insulation
Concrete and reinforcement (lenght on side of
structure)
Formwork
Pipe socket glued into the cone after removal of formwork
For bridge rehabilitation
by core boring(by owner)
Insulation
Concrete load-bearing structure
core boring
without sleeve, (lenght on side of
structure)
(clamp)
Stee
l gra
tings
, ho
t-dip
galv
anise
d
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Steel gratings, hot-dip galvanised
Bar grating stair treadsPrice group 400
Art. No. Description mesh € / piece06026-3330 600 mm x 260 mm, h 30 mm 30/30 u.r.07026-3330 700 mm x 260 mm, h 30 mm 30/30 u.r.08026-3330 800 mm x 260 mm, h 30 mm 30/30 u.r.09026-3330 900 mm x 260 mm, h 30 mm 30/30 u.r.10026-3330 1000 mm x 260 mm, h 30 mm 30/30 u.r.
Gratings with casing
Price group 400
Art. No. Description mesh € / piece05035-3120 500 mm x 350 mm, h 20 mm 30/10 u.r.06030-3120 600 mm x 300 mm, h 20 mm 30/10 u.r.06040-3120 600 mm x 400 mm, h 20 mm 30/10 u.r.07040-3120 700 mm x 400 mm, h 20 mm 30/10 u.r.08040-3120 800 mm x 400 mm, h 20 mm 30/10 u.r.08050-3120 800 mm x 500 mm, h 20 mm 30/10 u.r.08060-3120 800 mm x 600 mm, h 20 mm 30/10 u.r.09040-3120 900 mm x 400 mm, h 20 mm 30/10 u.r.09050-3120 900 mm x 500 mm, h 20 mm 30/10 u.r.10040-3120 1000 mm x 400 mm, h 20 mm 30/10 u.r.10050-3120 1000 mm x 500 mm, h 20 mm 30/10 u.r.10060-3120 1000 mm x 600 mm, h 20 mm 30/10 u.r.square-shaped03030-3325 a 300 mm, h 25 mm 30/30 u.r.04040-3330 a 400 mm, h 30 mm 30/30 u.r.05050-3330 a 500 mm, h 30 mm 30/30 u.r.06060-3340 a 600 mm, h 40 mm 30/30 u.r.
Garage collecting drain for car parks, without water supply,Content: 60 Liter
Price group 106
Art. No. Description € / piece30009 553 mm x 380 mm x 450 mm,
Content 60 Liter, accessible u.r.
30009-150 553 mm x 380 mm x 450 mm, Content 60 Liter, trafficable u.r.
30009-125L-PKW 550 mm x 550 mm x 640 mm, Content 125 Liter, trafficable u.r.
galvanised safety chain galvanised safety hook galvanised clamp
Safety device
Steel gratings, hot-dip galvanisedfor pedestrian traffic
Price group 400
Art. No. Description mesh € / piece05035-3320 500 mm x 350 mm, h 20 mm 30/30 u.r.06040-3320 600 mm x 400 mm, h 20 mm 30/30 u.r.07040-3320 700 mm x 400 mm, h 20 mm 30/30 u.r.08040-3320 800 mm x 400 mm, h 20 mm 30/30 u.r.08050-3320 800 mm x 500 mm, h 20 mm 30/30 u.r.09040-3320 900 mm x 400 mm, h 20 mm 30/30 u.r.09050-3320 900 mm x 500 mm, h 20 mm 30/30 u.r.10040-3320 1000 mm x 400 mm, h 20 mm 30/30 u.r.10050-3320 1000 mm x 500 mm, h 20 mm 30/30 u.r.08050-3325 800 mm x 500 mm, h 25 mm 30/30 u.r.08060-3325 800 mm x 600 mm, h 25 mm 30/30 u.r.09050-3325 900 mm x 500 mm, h 25 mm 30/30 u.r.09060-3325 900 mm x 600 mm, h 25 mm 30/30 u.r.10050-3325 1000 mm x 500 mm, h 25 mm 30/30 u.r.10060-3325 1000 mm x 600 mm, h 25 mm 30/30 u.r.10050-3330 1000 mm x 500 mm, h 30 mm 30/30 u.r.10060-3330 1000 mm x 600 mm, h 30 mm 30/30 u.r.
Garage gratings with casingtrafficable by passenger carsPrice group 400
Art. No. Description mesh € / piece10020-3330 1000 mm x 200 mm, h 30 mm 30/30 u.r.12520-3330 1250 mm x 200 mm, h 30 mm 30/30 u.r.20020-3330 2000 mm x 200 mm, h 30 mm 30/30 u.r.10025-3330 1000 mm x 250 mm, h 30 mm 30/30 u.r.12525-3330 1250 mm x 250 mm, h 30 mm 30/30 u.r.
Industrial gratings, loose
Price group 400
Art. No. Description mesh € / pieceI10050-3332R 1000 mm x 500 mm, h 30 mm 30/30 u.r.I100100-3332R 1000 mm x 1000 mm, h 30 mm 30/30 u.r.I10050-3333R 1000 mm x 500 mm, h 30 mm 30/30 u.r.I100100-3333R 1000 mm x 1000 mm, h 30 mm 30/30 u.r.
Stre
et an
d ya
rd g
ullie
s
�0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Concrete street gulliesDry sludge - models
for dry sludge
Street inlet high, long shaftconsisting of:
Top: Type ...*)Bucket: E8000 od E8811Compensating ring: 5008AShaft: 5005A(without bearing studs)Bottom: 5001-150 (-200)
Street inlet low, short Shaftconsisting of:
Top: Type ...*)Bucket: E8050 od E8812Compensating ring: 5008AShaft: 5005C(without bearing studs)Bottom: 5001-150 (-200)
Motorway gullyconsisting of:
Top: 1005HI(-SR) 1005WN 1005ABSCompensating ring: 5008ABottom: 5001-200 with rebate
for wet sludge
Street inlet consisting of:
Top: Type ...*)Compensating ring: 5008AShaft: 5005BSleeve: 5003-150(-200)
Extension: 5006ASump: 5002-300(-500)
Traps (odour traps)
*) Top with integrated bucket holder does not require inlet funnel. Use only shaft without bearing studs
Price group 070
1038A DN 100 u.r.1038B DN 125 u.r.1038C DN 150 u.r.
Stre
et an
d ya
rd g
ullie
s
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Street gullies
Concrete street gulliesParts Price group 111
Art. No. # Description Weight (kg) € / pieceCompensating ring with bearing studs (model Burgenland)5004C u DN 450, h 100 mm 51 u.r.Compensating ring5008A v DN 450, h 60 mm 25 u.r.
Shaft with bearing studs, do not use with integrated bucket-support5004A w DN 450, h 570 mm, long 125 u.r.5004B w DN 450, h 195 mm, short 50 u.r.
Shaft without bearing studs5005A x DN 450, h 670 mm 130 u.r.5005B x DN 450, h 295 mm 60 u.r.5005C x DN 450, h 195 mm 40 u.r.5005D x DN 450, h 570 mm 120 u.r.Sleeve without odour trap5003-150 y DN 450, h 350 mm, sleeve DN 150 80 u.r.5003-200 y DN 450, h 380 mm, sleeve DN 200 90 u.r.Sleeve with odour trap5003-150MGV z DN 450, h 490 mm, sleeve DN 150 150 u.r.Extension5006A { DN 450, h 295 mm 55 u.r.5006B { DN 450, h 195 mm 40 u.r.Sump5002-300 | DN 450, h 300 mm 125 u.r.Bottom with rebate5001-150 } DN 450, h 335 mm, PVC-sleeve DN 150 120 u.r.5001-200 } DN 450, h 400 mm, sleeve DN 200 125 u.r.
Bottom with odour trap and sleeve5001-150MGV ~ DN 450, h 415 mm, sleeve PVC DN 150 165 u.r.
u v w x y
z { | } ~
Stre
et an
d ya
rd g
ullie
s
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Concrete yard gullies DN �00for tops see chapter „gully grates and tops“
Yard gully high with odour trapconsisting of:- Compensating ring- Shaft- Bottomapplicable bucket: E8406, E8807l without top
Price group 110
Art. No. DN Outlet sleeve DN Class Weight
(kg) € / piece
BHOF-H-GV100 300 100 B 125 116 u.r.BHOF-H-GV150 300 150 B 125 138 u.r.
Yard gully low with odour trapconsisting of :- Compensating ring- Shaft- Bottomapplicable bucket: E8452, E8806 l without topPrice group 110
Art. No. DN Outlet sleeve DN Class Weight
(kg) € / piece
BHOF-N-GV100 300 100 B 125 94 u.r.BHOF-N-GV150 300 150 B 125 116 u.r.
Yard gully high without odour trap consisting of:- Compensating ring- Shaft- Bottomapplicable bucket: E8406, E8807l without top
Price group 110
Art. No. DN Outlet sleeve DN Class Weight
(kg) € / piece
BHOF-H-100 300 100 B 125 102 u.r.BHOF-H-150 300 150 B 125 112 u.r.
Yard gully low without odour trapconsisting of :- Compensating ring- Shaft- Bottomapplicable bucket: E8452, E8806 l without top
Price group 110
Art. No. DN Outlet sleeve DN Class Weight
(kg) € / piece
BHOF-N100 300 100 B 125 80 u.r.BHOF-N150 300 150 B 125 90 u.r.
Concrete parts Price group 110
Art. No. # Description Weight (kg) € / pieceCompensating ringBE300AR u DN 300, h 60 mm 25 u.r.Shaft without bearing studsBE300SCH280 v DN 300, h 280 mm 33 u.r.ExtensionBE300ZWT220 w DN 300, h 225 mm 20 u.r.Shaft without bearing studsBE300SCH510 x DN 300, h 510 mm 55 u.r.
Concrete parts Price group 110
Art. No. # Description Weight (kg) € / pieceBottom without odour trap
BE300UT100 uDN 300, h 255 mm,
sleeve DN 100 47 u.r.
BE300UT150 uDN 300, h 310 mm,
sleeve DN 150 57 u.r.
Bottom with odour trap
BE300UT100GV v DN 300, h 420 mm, sleeve DN 100 61 u.r.
BE300UT150GV v DN 300, h 530 mm, sleeve DN 150 83 u.r.
uv w x u
v
Slot
ted
buck
ets
and
dirt
pans
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Slotted bucket und Dirt pan
Slotted bucket made of plastic Price group 120
Art. No. # Description Weight (kg) € / piece
Slotted bucket high, for street gullyE8811 u clear opening 450 3,5 u.r.
Slotted bucket low, for street gullyE8812 v clear opening 450 2,0 u.r.
Slotted bucket high, for yard gullyE8807 w clear opening 300 0,9 u.r.
Slotted bucket low, for yard gullyE8806 x clear opening 300 0,7 u.r.
Dirt pan made of plastic Price group 120
Art. No. # Description Weight (kg) € / piece
Dirt pan low, galvanised steel crossbar, for manhole coversS8869 u DN 600 2,9 u.r.
Dirt pan deep, (240 mm), galvanised steel crossbar, for manhole coversS8869T v DN 600 3,0 u.r.Inlet funnel made of plastic (PE)T8894 - clear opening 450 0,5 u.r.
Slotted bucket made of galvanised steel Price group 120
Art. No. # Description Weight (kg) € / piece
Slotted bucket high, for street gullyE8000 u clear opening 450 6,5 u.r.
Slotted bucket low, for street gullyE8050 v clear opening 450 5,5 u.r.
Slotted bucket high, for yard gullyE8406 w clear opening 300 3,5 u.r.
Slotted bucket low, for yard gullyE8452 x clear opening 300 2,5 u.r.
Dirt pan made of galvanised steel Price group 120
Art. No. # Description Weight (kg) € / piece
Dirt pan low, light-weight model, for manhole coversS8614 u DN 600 4,5 u.r.
Dirt pan low, heavy-duty model, for manhole coversS8615 v DN 600 7,3 u.r.S8615A v light-weight, DN 600 4,4 u.r.ditto, without crossbarS8616 u DN 600 5,6 u.r.
Dirt pan deep, (220 mm), heavy-duty model, for manhole coversS8615T w DN 600 7,2 u.r.Inlet funnel made of galvanised steelT8900 - clear opening 450 1,5 u.r.
u v w x u v w x
u v u v
w
plastic galvanised steel
Surfa
ce b
oxes
and
hydr
ant c
ases
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Surface boxes and special covers, hydrant cases
Surface boxes Price group 030
Art. No. # Description Class kg €/piece1058A300 u DN 300, h 75 mm K 10 8,0 u.r.1058A300-S u as above, with lock K 10 8,4 u.r.1058A300-S-S u as above, with hinge and lock K 10 8,5 u.r.KTSCH9 - key u.r.1058D200 v DN 200, h 100 mm M 400 18,0 u.r.1058D200-S v as above, with lock M 400 18,0 u.r.SCHL2 - key 0,6 u.r.
141-4368-10-00 - DN 300, h 75 mmwith three locks M 400 36,0 u.r.
1058E400 w DN 400, h 60 mm M 600 55,0 u.r.
u v w
Surface boxes Price group 030
Art. No. # Description Class Weight (kg) €/piece
with cast iron cover17250-300 u DN 300, h 100 mm M 250 24,0 u.r.
17250-300S uas above, with two locks
and key M 250 24,0 u.r.
with concrete/cast iron cover87250-300 v DN 300, h 100 mm M 250 31,0 u.r.
u v
Cast iron hydrant cases Price group 150
Art. No. # Description Class kg €/piece141# u d 180, for water gate valves, h = 275 B 125 12,0 u.r.147# v d 92, for road valves, h = 250 B 125 6,0 u.r.149# u d 92, for low road valves, h = 155 B 125 4,0 u.r.144# w Surface box, oval 340/240, h = 310 C 250 33,0 u.r.1077-1 x oval 215/140, for garden valves, h = 160 6 kN 6,0 u.r.1077-2 x oval 250/180, for garden valves,h = 135 6 kN 6,0 u.r.1077-3 x oval 270/200, for garden valves,h = 150 6 kN 7,0 u.r.1078 y Box for road valves
* 150, h = 200 mm, AF: * 280 B 125 25,0 u.r.SCHKA-W - Surface box, * 180 (no image) D 400 30,0 u.r.1079 z 305 x 200, h = 220 B 125 48,0 u.r.200# { Ø 200, h = 225 - 355 B 125 48,0 u.r.
u v w x
y z {
Hist
orica
l cas
ting
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Historical casting
PostModel Otto Wagner 5Standard finish: bitumen-coated
Price group 182
Art. No. Description Height h mm kg € /
piece
STEHER-OW5-OB Octagonal post, without base plate 1425 58 u.r.
STEHER-OW5-OB-B With bore for chain holder 1425 58 u.r.STEHER-OW5-OB-L painted RAL 6005 1425 58 u.r.
STEHER-OW5UMKL Fold-down (ground clearance 210 mm) 1425 60 u.r.
STEHER-OW5SPH made of ductile graphite iron 1425 58 u.r.
Accessories
Price group 182
Art. No. Description €/pieceBOHÜ Base sleeve made of steel for OW5-OB u.r.BOHÜ-DE Cover for base sleeve u.r.STEHER-OW5SET Chain holder set for OW5 u.r.
Accessories
Price group 180
Art. No. # Description €/piece
KETTE-OOG uForged steel chain, raw,
oval-oval-links u.r.
KETTE-ROG vForged steel chain, raw,
round-oval-links u.r.
PostModel Krems
Price group 182
Art. No. Description Height h mm kg €/piece
STEHER-KREMS Model Krems 1350 u.r.
PostModels Otto Wagner Price group 182
Art. No. # Description Height h mm kg €/piece
STEHER-OW1 u Model Otto Wagner 1 1050 18 u.r.STEHER-OW7 v Model Otto Wagner 7 1020 18 u.r.STEHER-OW12v Model Otto Wagner 12 1020 18 u.r.SPANGE w Clip for OW 7 or OW 12 u.r.STEHER-OW6 x Model Otto Wagner 6 1020 18 u.r.STEHER-OW2 y Model Otto Wagner 2 1075 27 u.r.
E-GITTER zCast iron Edelweiss panel for mounting between two
OW2 posts740 u.r.
STEHER-OW3 { Model Otto Wagner 3 620 u.r.STEHER-OW4 { Model Otto Wagner 4 1090 u.r.
STEHER-OW8 � Bridge post Model Otto Wagner 8 1225 33 u.r.
u v w x
y z { �
u
v
Hist
orica
l cas
ting
�6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Historical casting
Spur post, bollard, bridge post Price group 180
Art. No. # Description Height h mm kg €/piece
RADABWEISER uSpur post, grey cast iron, raw 654 42 u.r.RADABWEISER-Su Spur post, SGCI, raw 654 42 u.r.RADABWEIS-SCHvMod. snail, grey cast iron, raw 470 55 u.r.RADABWEIS-SCH-Sv Mod. snail, SGCI, raw 470 55 u.r.POLLER w Bollard, grey cast iron, raw 600 160 u.r.l phase-out models
u v w
Benches and tables Price group 180
Art. No. # Description Lenghtmm kg € / Set
G-BANKFUSS-LG u
Garden bench side, painted green, model
Schönbrunn, grey cast iron, SET of 2 pieces
35 u.r.
G-BANK-HOLZ uWood planks (incl. fastening material) 1800 u.r.
G-TISCHFUSS-LG v
Table leg, grey cast iron, modell Gumpoldskir-chen, painted green
SET of 2 pieces
32 u.r.
G-TISCH-HOLZ vWood planks (incl. fastening material) 1600 u.r.
G-BANKFUSS6001wBench leg, grey cast iron,
modell Gumpoldskir-chen, painted green
15 u.r.
l without wood! Wood planking not included with legs
u v w
Tree gratings (tree grills)made of grey cast iron/SGCI, round Price group 182
Art. No. # Description Øa / Øi mm kg € / Set
Tree gratings (tree grills) made of grey cast iron Price group 182
BSS4R800-1600 u Tree grating model GrinzingSET of 4 segments
1600/800 55 u.r.
BSS4R800-2250 vTree grill model Kärntnerstr.
SET of 4 segments
2250/800 115 u.r.
BSS4R1000-2250 vTree grill model Kärntnerstr.
SET of 4 segments
2250/1000 103 u.r.
BSS8R800-3000 wTree grill model
SieveringSET of 8 segments
3000/800 153 u.r.
BSS8R1000-3000 wTree grill model
SieveringSET of 8 segments
3000/1000 145 u.r.
BSS8R800-3000Kx
Tree grill model Landstraße
with concentric slotsSET of 8 segments
3000/800 131 u.r.
Tree gratings (Tree grills) made of SGCI Price group 130
PM-RE99F2BD y Tree grating model Des-landes, SET of 4 segments
2000/600 38 u.r.
PM-RE99F0AD z Tree grating model MonetSET of 4 segments
1414/600 15 u.r.
u v w
x y z
Bollard ballhighly resillient to use as bump guard agaings cars and vehicles
Art. No. Description kg € / piecePollerkugel Ø 400 mm 44 u.r.
Hist
orica
l cas
ting
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Historical casting
Tree gratings (Tree grills)made of grey cast iron/SGCI, rectangular/square/cambered shaped
Price group 181
Art. No. # Description mm kg € / SetTree gratings (Tree grills) made of gray cast iron
BSS4QU600-1800u Tree grating model MödlingSET of 4 segments
1800x1800/600
108 u.r.
BSS8QU800-3000vTree grill model
DonauinselSET of 8 segments
3000x3000/800
203 u.r.
BSS8QU800-3000KwTree grill model Hiltonwith concentric slots SET of 8 segments
3000x3000/800
176 u.r.
BSS8QU3000-G2 xTree grill model Graz
with square-shaped ope-nings, SET of 8 segments
3000x3000/1000
131 u.r.
BS-EUROPA yTree grating model Europawith square-shaped ope-nings, SET of 8 segments
32002180/800
1340 u.r.
Tree gratings (Tree grills) made of SGCI Price group 130
PM-RE99FOCD +PM-RE99FOJD v
Tree grating model Fantin-Latour
SET of 4 segments
1414x1414/600
23 u.r.
Tree gratings (Tree grills) made of SGCI, cambered shapedPM-RE99F18D +PM-RE99F1GD u Tree grating model Santorin
SET of 4 segments1450/750 15 u.r.
u v w
x y
u v
Tree protection railing
Price group 180
Art. No. # Description Ø Amm
Ø Bmm
hmm €/piece
BG1 u galvanised steel 375 900 1740 u.r.BG2 u galvanised steel 500 1250 1800 u.r.BG5 v Forged iron 375 900 1750 u.r.
u v
Base structure
Hot-dip galvanised steel base structure upon requestONLY based on actual measurements!
Cast iron snow poles Base sleeves made of steel
Price group 150
Art. No. # Description €/pieceSCHNHA300 u h = 300 mm, d = 70 mm u.r.SCHNHA450 u h = 450 mm, d = 70 mm u.r.BODENHÜLSE60 v h = 500 mm, d = 60 mm u.r.BODENHÜLSE70 v h = 500 mm, d = 70 mm u.r.
u v
Cast iron rain pipemodel „Antique“
Price group 180
Art. No. # Description €/pieceMLRSTR070 - Rain pipe, DN 70 u.r.MLRSTR0100 - Rain pipe, DN 100 u.r.MLROSTRO100ANTIK u Rain pipe, DN 100 u.r.
u
Hist
orica
l cas
ting
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Tree gratings (Tree grills)made of cast iron, ray design Price group 181
Art. No. # L/D (mm) Hmm kg €/piece
BS-S-1250-600 u 1250/600 41 102 u.r.BS-S-1500-700 u 1500/700 41 128 u.r.BS-S-1900-700 u 1900/700 41 238 u.r.BS-S-2000-700 u 2000/700 41 260 u.r.BS-S-2300-700 u 2300/700 46 354 u.r.BS-S-2500-700 u 2500/700 46 400 u.r.BS-S-3000-800 u 3000/800 46 640 u.r.
BS-SQ-1000-600 v 1000/600 41 75 u.r.BS-SQ-1250-600 v 1250/600 41 145 u.r.BS-SQ-1400-700 v 1400/700 41 147 u.r.BS-SQ-1500-700 v 1500/700 41 168 u.r.BS-SQ-1800-700 v 1800/700 41 275 u.r.BS-SQ-1900-700 v 1900/700 41 297 u.r.BS-SQ-2000-700 v 2000/700 41 332 u.r.BS-SQ-2300-700 v 2300/700 46 525 u.r.BS-SQ-2500-700 v 2500/700 46 595 u.r.BS-SQ-3000-700 v 3000/800 46 960 u.r.l matching supports and tree protection railings upon request
Historical casting
Tree gratings (Tree grills)made of cast iron, radial design Price group 181
Art. No. # L/D (mm) Hmm kg €/piece
BS-R-1250-600 u 1250/600 41 115 u.r.BS-R-1500-700 u 1500/700 41 145 u.r.BS-R-1900-700 u 1900/700 41 265 u.r.BS-R-2000-700 u 2000/700 41 285 u.r.BS-R-2300-700 u 2300/700 46 390 u.r.BS-R-2500-700 u 2500/700 46 440 u.r.BS-R-3000-800 u 3000/800 46 720 u.r.
BS-RQ-1000-600 v 1000/600 41 85 u.r.BS-RQ-1250-600 v 1250/600 41 160 u.r.BS-RQ-1400-700 v 1400/700 41 165 u.r.BS-RQ-1500-700 v 1500/700 41 185 u.r.BS-RQ-1800-700 v 1800/700 41 300 u.r.BS-RQ-1900-700 v 1900/700 41 325 u.r.BS-RQ-2000-700 v 2000/700 41 365 u.r.BS-RQ-2300-700 v 2300/700 46 575 u.r.BS-RQ-2500-700 v 2500/700 46 650 u.r.BS-RQ-3000-700 v 3000/800 46 1060 u.r.l matching supports and tree protection railings upon request
u v
Viennese Bassena (communal water tap)model „Wallner & Neubert“, incl. odour trap, facing and grating
Price group 180
Art. No. Description €/pieceBASSENA-KOMPL model „Wallner & Neubert“ u.r.
Traditional Viennese tapmade of brass, incl. rosette
Price group 180
Art. No. # Description €/piece
BASS-HAHN-FRA uTap model „Frankfurt“
heavy-duty model, with winter shut-off
u.r.
BASS-HAHN-NOS - Tap model „Nostalgia“light-weight model u.r.
u
����
u v
Box g
utte
rs
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Examples of uses of box gutters
PDC Installation in asphalt
PDC Installation in cobblestone
PDC Installation in concrete
l For installation drawings and installation directions for gutters conforming to EN 1433 contact our office
PURADRAIN® made of precast polymer concrete
PDC-Domo gutter, clear opening 100The gutter for private residences (garage drive, etc..) Art. No. Nominal
length (mm)Nominal
height (mm)Weight
(kg) € / piece
Price group 010
PDC-DOMO 1000 80 6,5 u.r.DOMO end panelPDC-TDOMO100C - - 0,3 u.r.DOMO box gutter 500x300x130 - EuroPDC-A-EURO100 500 300 u.r.DOMO bar-type gratingPDC-GN100UCA 1000 - 1,8 u.r.DOMO Cast iron grating - Class C 250 kNPDC-FNX100UCCM 500 - 2,3 u.r.
concrete coating base layer
frost-free underground
sandbed
base layer
each first block in concrete
concrete coatingfrost-free underground
concrete coating
frost-free underground
base layerconcrete coating
concrete slabexpansion joint
ClassC 250D 400E 600F 900
ClassA 015B 125
ClassA 015
ClassB 125
ClassC 250
ClassA 015 D 400B 125 E 600C 250 F 900
Box g
utte
rs
�0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURADRAIN® PDC 100 UK and Mini gutter made of precast polymer concrete
Type UK end panel, clear opening 100end panel, galvanised steel, closed versionPrice group 010
Art. No. Nominal height (mm)
Weightkg € / piece
PDC-T100K00C 150 mm 0,4 u.r.
PDC-T100K05C 175 mm 0,5 u.r.
PDC-T100K10C 200 mm 0,6 u.r.
PDC-T100K15C 225 mm 0,7 u.r.
PDC-T100K20C 250 mm 0,8 u.r.
Type Mini MK... Gutter, LW100 Drainage gutter with galvanised steel case A15 up to C250, b=130mm with minor insertion depth, without pitch, b=130mm
Price group 010
Art. No. Drainage Nominal length (mm)
Nominal height (mm)
Weightkg € / piece
PDC-M100K ò 1000 80 11,20 u.r.
Type Mini MK, end panel, clear opening 100end panel, galvanised steel, closed versionPrice group 010
Art. No. Nominal height (mm)
Weightkg
€ / piece
PDC-T100MKC 80 mm 0,2 u.r.
Type UK + MK intake box, clear opening 100b=130 mm, without basketPrice group 010
Art. No. Descrip-tion
Weightkg
€ / piece
PDC-AEURO100K length 500 mmheight 318 mm 16 u.r.
PDC-AK100 length 500 mmheight 560 mm 26 u.r.
PDC-CU100 basket for AK 100 - u.r.
PDC-CEURO100 basket for Euro - u.r.
Type UK end panel, clear opening 100end panel, galvanised steel, with outlet clear opening 100Price group 010
Art. No. Nominal height (mm)
Weightkg
€ / piece
PDC-T100K00A 150 mm 0,2 u.r.
PDC-T100K05A 175 mm 0,3 u.r.
PDC-T100K10A 200 mm 0,4 u.r.
PDC-T100K15A 225 mm 0,5 u.r.
PDC-T100K20A 250 mm 0,6 u.r.
Type UK... Gutter, clear opening 100 Price group 010
Drainage gutter with galvanised steel case A15 up to C250, b=130mm
Art. No. Pitch0,5 % Drainage
Nominal length (mm)
Nominal height (mm)
Weightkg € / piece
PDC-U100K00R - ò 1000 150 15,1 u.r.PDC-U100K01 a 1000 155 15,1 u.r.PDC-U100K02 a 1000 160 15,1 u.r.PDC-U100K03 a 1000 165 15,1 u.r.PDC-U100K04 a 1000 170 15,1 u.r.PDC-U100K05 a 1000 175 17,3 u.r.PDC-U100K05R - ò 1000 175 17,3 u.r.PDC-U100K06 a 1000 180 17,3 u.r.PDC-U100K07 a 1000 185 17,3 u.r.PDC-U100K08 a 1000 190 17,3 u.r.PDC-U100K09 a 1000 195 17,3 u.r.PDC-U100K10 a 1000 200 18,9 u.r.PDC-U100K10R - òð 1000 200 18,9 u.r.PDC-U100K11 a 1000 205 18,9 u.r.PDC-U100K12 a 1000 210 18,9 u.r.PDC-U100K13 a 1000 215 18,9 u.r.PDC-U100K14 a 1000 220 18,9 u.r.PDC-U100K15 a 1000 225 20,5 u.r.PDC-U100K15R - òð 1000 225 20,5 u.r.PDC-U100K16 a 1000 230 20,5 u.r.PDC-U100K17 a 1000 235 20,5 u.r.PDC-U100K18 a 1000 240 20,5 u.r.PDC-U100K19 a 1000 245 20,5 u.r.PDC-U100K20 a 1000 250 22,3 u.r.PDC-U100K20R - òð 1000 250 22,3 u.r.PDC-U100K25R - òð 1000 275 24,5 u.r.PDC-U100K30R - òð 1000 300 26,5 u.r.ò for vertical drainage ð for horizontalen drainage
Box g
utte
rs
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURADRAIN® PDC 100 UK and Mini gutter - Accessories
Gratings for type UK, clear opening 100 Price group 010
Art. No. # Description Nominal height (mm) Class Weight (kg) € / piecegalvanisedPDC-GN100KCA u bar-type grating 1000 A 15 1,7 u.r.PDC-GP100KCA v perforated grating 1000 A 15 1,7 u.r.PDC-GE100KCB w mesh grating 1000 B 125 2,9 u.r.stainless steelPDC-IN100KCA u bar-type grating 1000 A 15 1,7 u.r.PDC-IP100KCA v perforated grating 1000 A 15 1,7 u.r.PDC-IE100KCB w mesh grating 1000 B 125 3,0 u.r.cast ironPDC-FNX100KCCM x bart-type grating 500 C 250 3,4 u.r.plastic gratingPDC-VB100KOA y longitudinal slot grating 1000 A 15 1,5 u.r.PDC-PP100KCAM z perforated grating PP 500 A 15 0,5 u.r.
Lock for type UK and MKclear opening 100requires 2 pcs. / m1
Price group 010
Art. No. Description Weight (kg)
€ / piece
PDC-TEF860 screws for Mini h = 80 mm see gratings image w + x 0,1 u.r.
PDC-TNPC870 screws for Mini h = 80 mm see gratings image u + v 0,1 u.r.
PCD-CS100 toggle for UK 0,1 u.r.PDC-TEF850 screws for CS 100 for UK 0,1 u.r.
Anti-syphon trap
Price group 010
Art. No. Description Weight (kg) € / piecePDC-ES110 syphon DN 110 4 u.r.PDC-ES160 syphon DN 160 4 u.r.
u v w x y z
Box g
utte
rs
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Gratings for FMF... gutter, clear opening 100
Price group 010 Art. No. # Description Nominal length (mm) Class kg € /
piecePDC-FE100FTEM v GUGI ductile iron mesh grating 500 E 600 3,4 u.r.PDC-FC100FTFM w cast iron slab 500 F 900 7,4 u.r.PDC-FN100FTFM u cast iron slotted bar-type
grating 500 F 900 6,9 u.r.
PURADRAIN® PDC�00 FMF gutter made of precast polymer concrete
Type FMF... gutter, clear opening 100 Drainage gutter with galvanised steel case, class A 15 up to C 250, b = 163 mm, conforming to EN 1433, without pitch
Price group 010 Art. No. Pitch Nominal length (mm)
Nominal height (mm)
Weight (kg) € / piece
PDC-F100MF000R - 1000 130 23,0 u.r.PDC-F100MF00R - 1000 190 27,5 u.r.PDC-F100MF10R - 1000 250 30,0 u.r.PDC-F100MF20R - 1000 310 36,1 u.r.
u v w
Screw connectionrequires 8 pcs. / m1
Price group 010
Art. No. Description Weight (kg) € / piecePDC-TF1023 Screw - u.r.
Pitch element
Price group 010
Art. No. Description € / piece
PDC-CEF100 Pitch element for gutter installed with pitch u.r.
Intake box
Price group 010
Art. No. Description Weight (kg) € / piecePDC-AMF100 without basket
500x580x160 mm - u.r.EimerPDC-CF100 basket - u.r.
End panel, clear opening 100end panel, galvanised steel, closed version
Price group 010
Art. No. Nominal height (mm)
Weightkg € / piece
PDC-T100F000C 130 mm 0,5 u.r.PDC-T100F00C 190 mm 0,6 u.r.PDC-T100F10C 250 mm 0,7 u.r.PDC-T100F20C 310 mm 0,8 u.r.
End panel, clear opening 100end panel, galvanised steel, with outlet clear opening 100
Price group 010
Art. No. Nominal height (mm)
Weightkg € / piece
PDC-T100F00A 190 mm 0,4 u.r.PDC-T100F10A 250 mm 0,5 u.r.PDC-T100F20A 310 mm 0,6 u.r.
Installation variant without pitch Installation variant with pitch
Anti-syphon trap
Price group 010
Art. No. Description Weight (kg) € / piecePDC-ES110 syphon DN 110 4 u.r.PDC-ES160 syphon DN 160 4 u.r.
Box g
utte
rs
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURADRAIN® PDC MK gutter (shallow) made of precast polymer concrete
Type Mini MK.. gutter, clear opening 150 Drainage gutter with galvanised steel case, class A 15 up to C 250 mm, 102 mm insertion depth, without pitch, l= 1000 mm, b=204 mm
Price group 010
Art. No. Width Weigthkg
€ / piece
PDC-M150K outside 204inside 150 17,2 u.r.
Type Mini MK.. gutter, clear opening 200 Drainage gutter with galvanised steel case, class A 15 up to C 250 mm, 125 mm insertion depth, without pitch, l= 1000 mm, b=260 mm
Price group 010
Art. No. Width Weigthkg
€ / piece
PDC-M200K outside 260inside 200 23,1 u.r.
Type Mini MK.. gutter, clear opening 300 Drainage gutter with galvanised steel case, class A 15 up to C 250 mm, 150 mm insertion depth, without pitch, l= 1000 mm, b=360 mm
Price group 010
Art. No. Width Weigthkg
€ / piece
PDC-M300K outside 360inside 300 31,0 u.r.
Gratings for type MK... gutter, clear opening 150, b = 194 mm, l = 1000mm
Price group 010
Art. No. Description Class kg € / piece
PDC-FNX150KCCM cast iron slotted grating C 250 5,2 u.r.
PDC-GP150KCA perforated graing, galvanised A 15 3,5 u.r.
PDC-GE150KCB mesh grating, gavanised B 125 5,1 u.r.
PDC-IP150KCA Stainless steel perforated grating A 15 2,8 u.r.
PDC-IE150KCB mesh grating, stainless steel B 125 5,2 u.r.
MK intake box, clear opening 150, 500x400x204 mmPrice group 010Art. No. Description € / piece
PDC-ASELF200K without basket length 500 mm u.r.
EimerPDC-CSELF200 basket u.r.
MK end panel, clear opening 150, closed verison, galvanised steel
Price group 010
Art. No. Description Weightkg € / piece
PDC-T150MKC geschlossen 0,6 u.r.
MK end panel, clear opening 200, closed version, galvanised steel
Price group 010
Art. No. Description Weightkg € / piece
PDC-T200MKC geschlossen 0,6 u.r.
MK end panel, clear opening 300, closed version, galvanised steel
Price group 010
Art. No. Description Weightkg € / piece
PDC-T300MKC geschlossen 0,6 u.r.
Gratings for type MK... gutter, clear opening 200, b = 250 mm, l = 1000mm
Price group 010
Art. No. Description Class kg € / piece
PDC-FNX200KCCM cast iron slotted grating C 250 8,4 u.r.
PDC-GE200KCB mesh grating, gavanised B 125 8,1 u.r.
PDC-IE-200KCB mesh grating, stainless steel B 125 8,5 u.r.
Gratings for type MK... gutter, clear opening 300, b = 350 mm, l = 1000mm
Price group 010
Art. No. Description Class kg € / piece
PDC-FNX300KCCM cast iron slotted grating C 250 13,5 u.r.
PDC-GE300KCB mesh grating, gavanised B 125 13,5 u.r.
PDC-IE-300KCB mesh grating, stainless steel B 125 14,0 u.r.
MK intake box, clear opening 200, 500x363x260 mmPrice group 010Art. No. Description € / piece
PDC-AK200K without basket length 500 mm u.r.
EimerPDC-C200 basket u.r.
MK intake box, clear opening 300, 500x390x360 mmPrice group 010Art. No. Description € / piece
PDC-A300K without basket length 500 mm u.r.
EimerPDC-C300 basket u.r.
*
* l = 500 mm
* *
* l = 500 mm * l = 500 mm
l Locks and screw connections upon requestl Gratings for intake box (500 mm) upon request
Anti-syphon trap
Price group 010
Art. No. Description kg € / pc.PDC-ES110 syphon DN 110 4 u.r.PDC-ES160 syphon DN 160 4 u.r.
Box g
utte
rs
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Please note instructions in EN 1433:Extract from standard:In placing the foundation and the shell• as appropriate for type of gutters• as appropriate for load class• as appropriate for point of installationnote the manufacurer‘s general instructions for installation
Type SMMF... gutter, clear opening 150 Drainage gutter with galvanised steel case, class D 400 up to F 900 mm, 100 mm insertion depth, without pitch, l= 1000 mm, b=210 mm
Price group 010
Art. No. Width Weightkg
€ / piece
PDC-SM200MF outside 210inside 150 17,0 u.r.
Type SMMF... gutter, clear opening 200 Drainage gutter with galvanised steel case, class D 400 up to F 900 mm, 125 mm insertion depth, without pitch, l= 1000 mm, b=266 mm
Price group 010
Art. No. Width Weightkg
€ / piece
PDC-SM250MF outside 260inside 200 22,9 u.r.
Type SMMF... gutter, clear opening 300 Drainage gutter with galvanised steel case, class D 400 up to F 900 mm, 150 mm insertion depth, without pitch, l= 1000 mm, b=366 mm
Price group 010
Art. No. Width Weightkg
€ / piece
PDC-SM350MF outside 366inside 300 35,0 u.r.
Gratings for Type SMMF... gutter, clear opening 150, b = 190 mm, l = 500 mm, cast iron
Price group 010
Art. No. Description Class kg € / piece
PDC-FNX150FTDM Slotted grating D 400 5,2 u.r.PDC-FN150FTFM Slotted grating F 900 12,1 u.r.PDC-FC150FTFM plate F 900 12,9 u.r.
Gratings for Type SMMF... gutter, clear opening 200, b = 254 mm, l = 500 mm, cast iron
Price group 010
Art. No. Description Class kg € / piece
PDC-FNX200FTDM Slotted grating D 400 5,7 u.r.PDC-FN200FTFM Slotted grating F 900 13,0 u.r.PDC-FC200FTFM plate F 900 14,5 u.r.
Gratings for Type SMMF... gutter, clear opening 300, b = 346 mm, l = 500 mm, cast iron
Price group 010
Art. No. Description Class kg € / piece
PDC-FN300FTDM Slotted grating D 400 14,4 u.r.PDC-FN300FTFM Slotted grating F 900 25,2 u.r.PDC-FC300FTFM plate F 900 27,9 u.r.
Intake box,clear opening 150500x400x210 mmPrice group 010Art. No. Description € / piece
PDC-AS200MF without basket length 500 mm u.r.
EimerPDC-CSELF200 basket u.r.
MK end panel, clear opening 150, clesed versoin, galvanised steel
Price group 010
Art. No. Description Weightkg € / piece
PDC-T150MKC closed version 0,6 u.r.
Intake box, clear opening 200500x363x266 mmPrice group 010Art. No. Description € / piece
PDC-AMF200 without basket length 500 mm u.r.
EimerPDC-C200 basket u.r.
MK end panel, clear opening 200, closed versoin, galvanised steel
Price group 010
Art. No. Description Weightkg € / piece
PDC-T200MKC closed version 0,6 u.r.
Intake box, clear opening 300500x390x366 mmPrice group 010Art. No. Description € / piece
PDC-AMF300 without basket length 500 mm u.r.
EimerPDC-C300 basket u.r.
MK end panel, clear opening 300, closed version, galvanised steel
Price group 010
Art. No. Description Weightkg € / piece
PDC-T300MKC closed version 0,6 u.r.
PURADRAIN® PDC SMMF gutter (shallow) made of precast polymer concrete
Screw connectionrequires 8 pcs. / m1
Price group 010
Art. No. Description Weight (kg) € / piecePDC-TF1023 Screw - u.r.
Was
te w
ater
pur
ifica
tion
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Table of contentsWaste water purification
Cesspools 56
Sewage treatment plants 60
Mineral oil seperators 63
Grease seperators 74
Conveyor technique 93
Concrete parts 106
Cess
pool
s
�6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Concrete cesspoolsring design, with floor and cover, without step irons Price group 091
Art. No. Capacity m³ Inner ØD m
Wall thick-ness s cm
Inlet depthZt m
Insertion depthEt m
Weight t
weight of largest
part t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
l IMPORTANT NOTE:Provide cesspool with protective coating in-side before taking it into operation. Requirement about 0,6 kg/m²
SG-15-3,20BO 3,20 1,50 8 0,88 2,77 3,4 1,20 u.r. u.r. u.r.SG-15-4,10BO 4,10 1,50 8 0,88 3,28 3,9 1,20 u.r. u.r. u.r.SG-15-4,95BO 4,95 1,50 8 0,88 3,79 4,4 1,20 u.r. u.r. u.r.
SG-20-3,35BO 3,35 2,00 9 0,99 2,10 4,1 1,85 u.r. u.r. u.r.SG-20-4,15BO 4,15 2,00 9 0,99 2,35 4,5 1,85 u.r. u.r. u.r.SG-20-4,95BO 4,95 2,00 9 0,99 2,61 4,8 1,85 u.r. u.r. u.r.SG-20-5,70BO 5,70 2,00 9 0,99 2,85 5,2 1,85 u.r. u.r. u.r.SG-20-6,50BO 6,50 2,00 9 0,99 3,11 5,6 1,85 u.r. u.r. u.r.SG-20-7,30BO 7,30 2,00 9 0,99 3,36 5,9 1,85 u.r. u.r. u.r.SG-20-8,10BO 8,10 2,00 9 0,99 3,62 6,3 1,85 u.r. u.r. u.r.SG-20-8,90BO 8,90 2,00 9 0,99 3,86 6,7 1,85 u.r. u.r. u.r.SG-20-9,70BO 9,70 2,00 9 0,99 4,12 7,0 1,85 u.r. u.r. u.r.
SG-25-5,00BO 5,00 2,50 9 1,23 2,34 5,8 2,65 u.r. u.r. u.r.SG-25-6,30BO 6,30 2,50 9 1,23 2,59 6,2 2,65 u.r. u.r. u.r.SG-25-7,55BO 7,55 2,50 9 1,23 2,85 6,7 2,65 u.r. u.r. u.r.SG-25-8,80BO 8,80 2,50 9 1,23 3,09 7,2 2,65 u.r. u.r. u.r.SG-25-10,00BO 10,00 2,50 9 1,23 3,35 7,6 2,65 u.r. u.r. u.r.SG-25-11,20BO 11,20 2,50 9 1,23 3,60 8,1 2,65 u.r. u.r. u.r.SG-25-12,50BO 12,50 2,50 9 1,23 3,86 8,5 2,65 u.r. u.r. u.r.SG-25-13,75BO 13,75 2,50 9 1,23 4,10 9,0 2,65 u.r. u.r. u.r.SG-25-14,95BO 14,95 2,50 9 1,23 4,36 9,5 2,65 u.r. u.r. u.r.SG-25-16,10BO 16,10 2,50 9 1,23 4,61 9,9 2,65 u.r. u.r. u.r.l Cesspools without floor upon request
Concrete cesspools
Bituminous coatingfor cesspools in ring design Price group 000
Art. No. Descreption € / piece
Schutzanstrich - 25 kg Bituminous coating, 25kg can u.r.
ALARM SYSTEMfor cesspools, with obstruction-triggered alarm and float switch Price group 000
Art. No. Descreption € / piece
ALARM-SG-10M Alarm System incl.10m cable u.r.ALARM-SG-20M Alarm System incl.20m cable u.r.
Cess
pool
s
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Concrete cesspoolscompact design Price group 092
Art. No. Capacity m³
Inner ØD m
Wall thick-ness s cm
InletDNmm
Inlet depthZt m
Insertion depthEt m
Weight t
weight of largest
part t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
SGKom-15-2,9 2,9 1,50 10 150 0,91 2,67 3,8 3,1 u.r. u.r. u.r.SGKom-20-5,2 5,2 2,00 10 150 0,98 2,74 5,9 4,7 u.r. u.r. u.r.SGKom-20-6,81 6,8 2,00 10 150 0,98 3,25 6,6 5,5 u.r. u.r. u.r.SGKom-20-8,41 8,4 2,00 10 150 0,98 3,75 7,4 4,7 u.r. u.r. u.r.SGKom-20-10,01 10,0 2,00 10 150 0,98 4,25 8,1 4,7 u.r. u.r. u.r.SGKom-20-11,51 11,5 2,00 10 150 0,98 4,76 8,8 4,7 u.r. u.r. u.r.
SGKom-25-8,00 8,0 2,50 12 150 1,23 2,98 8,2 6,5 u.r. u.r. u.r.SGKom-25-10,51 10,5 2,50 12 150 1,23 3,49 9,1 6,5 u.r. u.r. u.r.SGKom-25-13,01 13,0 2,50 12 150 1,23 3,99 10,1 6,5 u.r. u.r. u.r.SGKom-25-15,51 15,5 2,50 12 150 1,23 4,49 11,0 6,5 u.r. u.r. u.r.SGKom-25-18,01 18,0 2,50 12 150 1,23 5,00 11,9 6,5 u.r. u.r. u.r.1 2-part compact unit; joint is factory-sealed (not possible below 0° C). Joints in the cone and any extension rings
that may be required have to be sealed at construction site.
Concrete cesspools
City-of-Vienna-approved cesspoolcompact design, with step irons, pump sump Price group 092
Art. No. Capacity m³
Inner ØD m
Wall thick-ness s cm
InletDNmm
Inlet depthZt m
Insertion depthEt m
Weight t
weight of largest
part t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
l Also available with anti-buoyancy protection for diameters 2.00m and 2.5m.
SGSTKom-20-5,2 5,2 2,00 10 150 0,87 2,63 6,7 4,7 u.r. u.r. u.r.SGSTKom-20-6,81 6,8 2,00 10 150 0,87 3,14 7,4 5,5 u.r. u.r. u.r.SGSTKom-20-8,41 8,4 2,00 10 150 0,87 3,65 8,1 4,7 u.r. u.r. u.r.SGSTKom-20-10,01 10,0 2,00 10 150 0,87 4,16 8,9 4,7 u.r. u.r. u.r.SGSTKom-20-11,51 11,5 2,00 10 150 0,87 4,67 9,6 4,7 u.r. u.r. u.r.
SGSTKom-25-8,00 8,0 2,50 12 150 0,87 2,63 9,6 6,5 u.r. u.r. u.r.SGSTKom-25-10,51 10,5 2,50 12 150 0,87 3,14 10,5 6,5 u.r. u.r. u.r.SGSTKom-25-12,91 12,9 2,50 12 150 0,87 3,65 11,4 6,5 u.r. u.r. u.r.SGSTKom-25-15,31 15,3 2,50 12 150 0,87 4,16 12,3 6,5 u.r. u.r. u.r.SGSTKom-25-17,71 17,7 2,50 12 150 0,87 4,67 13,3 6,5 u.r. u.r. u.r.1 2-part compact unit; joint is factory-sealed (not possible below 0° C). Joints in the cone and any extension rings
that may be required have to be sealed at construction site.
ADVANTAGES of compact-type cesspools • Compact bottom structure of 2 m height • units are plant-tested for tightness before leaving the factory • integrated DN 150 socket for immediate connection to building • tightness certificate issued free of charge
Cess
pool
s
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
GRP cesspools made of glass-fibre-reinforced plastic
GRP cesspoolsmade of glass-fibre-reinforced pastic, horizontal tank Price group 092
Art. No. Capacity m³ Inner ØD m
Length L m
InletDNmm
Inlet depthZt m
Insertion depthEt m
Weight t
weight of largest part t € / piece
B-GFK-3N1,25 3,0 1,25 2,62 150 0,76 2,06 0,44 0,18 u.r.B-GFK-4N1,25 4,0 1,25 3,45 150 0,76 2,06 0,48 0,22 u.r.B-GFK-5N1,50 5,0 1,50 3,10 150 0,76 2,31 0,52 0,27 u.r.B-GFK-6N1,50 6,0 1,50 3,65 150 0,76 2,31 0,56 0,31 u.r.B-GFK-8N1,50 8,0 1,50 4,80 150 0,76 2,31 0,64 0,38 u.r.B-GFK-10N1,70 10,0 1,70 4,75 150 0,76 2,51 0,74 0,48 u.r.B-GFK-15N2,00 15,0 2,00 5,10 150 0,76 2,81 0,92 0,66 u.r.B-GFK-20N2,00 20,0 2,00 6,67 150 0,76 2,81 1,10 0,85 u.r.
B-GFK-3W1,25 1 3,0 1,25 2,62 150 0,76 2,06 0,46 0,20 u.r.B-GFK-4W1,25 1 4,0 1,25 3,45 150 0,76 2,06 0,50 0,25 u.r.B-GFK-5W1,50 1 5,0 1,50 3,10 150 0,76 2,31 0,55 0,30 u.r.B-GFK-6W1,50 1 6,0 1,50 3,65 150 0,76 2,31 0,59 0,33 u.r.B-GFK-8W1,50 1 8,0 1,50 4,80 150 0,76 2,31 0,67 0,41 u.r.B-GFK-10W1,70 1 10,0 1,70 4,75 150 0,76 2,51 0,76 0,50 u.r.B-GFK-15W2,00 1 15,0 2,00 5,10 150 0,76 2,81 0,95 0,69 u.r.B-GFK-20W2,00 1 20,0 2,00 6,67 150 0,76 2,81 1,20 0,88 u.r.1 with stepladder and pump sump, designed in accordance with City of Vienna guidelinel to be installed only in accessible area; other inlet depths and diameters upon request
Cess
pool
s
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PE water meter pitincl. grey iron cover with seal, Flex tube, without water meter Price group 436
Art. No. Cover Inner Ø D mm
Pipe cover m Inner thread € / piece
EWE-0399631 Class A 384 1,00 Rp 1“ u.r.EWE-0399632 Class A 384 1,25 Rp 1“ u.r.EWE-0399633 Class A 384 1,50 Rp 1“ u.r.l The water meter is easy to pull out, therefore low assembly costs with OVGW (Austrian Association for Gas and
Water) ball-type shut-off valves and insulating lid. For details and water meter see chapter on water supply
Concrete water meter pitcompact design Price group 092
Art. No. cover type Inner Ø D mm
wall thicknesscm
Insertion depthm
Weightt
weight of largest part t € / piece
WA-SCH-100 1B concrete 1,00 10 1,63 1,8 1,5 u.r.WA-SCH -100 17136 steel checker plate 1,00 10 1,63 1,8 1,5 u.r.
WA-SCH-100 17166 galvanised, impermea-bility to surface water 1,00 10 1,63 1,8 1,5 u.r.
l Cover accessible, step irons factory-provided
Concrete water meter pitcompact design, with pump sump conforming to City of Vienna guideline Price group 092
Art. No. cover type Inner Ø D mm
wall thicknesscm
Insertion depthm
Weightt
weight of largest part t € / piece
WA-SCH -120 17136 steel checker plate 1,20 10 2,21 3,3 2,7 u.r.
WA-SCH-120 17166 galvanised, impermea-bility to surface water 1,20 10 2,21 3,3 2,7 u.r.
l Cover accessible, step irons factory-provided, water meter pit built to Viennese communal standard rules sheet
Water meter pits
Sew
age t
reat
men
t plan
ts
60
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Sewage treatment plants
• Customised solutions• Water rights project• Aid project and application• Representation before authorities• Further purification stages• etc.
our PURATOR engineering team will be pleased to assist you!
ADVANTAGES Compact and tight containers: easy to install High performance: excellent effluent qualityAdjustable: to meet every needLow running and maintenance costs
Sew
age t
reat
men
t plan
ts
6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURACOS - Small sewage treatment plants - concrete from 5 up to 40 inhabitants equivalentsconsisting of primary sedimentation basin, activated sludge tank and sedimentation/circulation basin Price groupe 093
Art. No. max. IE
Inlet, outlet DN mm
Inlet depthZt m
Outlet depthAt m
Installati-on Depth
Et m
Inner Ø D or
L x B m
Weight t
weight of largest part t
€ / piece125 kN
€ / piece400 kN
PURACOS-5 5 150/100 1,13 1,18 2,88 2,00 7,9 6,8 u.r. u.r.PURACOS-10 10 150/100 1,13 1,18 2,88 2,00 7,9 6,8 u.r. u.r.PURACOS-15 15 150/100 1,28 1,38 3,13 2,50 11,4 9,7 u.r. u.r.PURACOS-20 20 150/150 1,28 1,33 3,53 2,50 12,8 11,2 u.r. u.r.PURACOS-30 30 150/150 0,91 1,01 3,01 3,85 x 2,50 18,7 13,7 u.r. u.r.PURACOS-40 40 150/150 0,91 0,96 3,11 3,85 x 2,50 19,5 14,5 u.r. u.r.l PURACOS - sewage treatment plants over 40 IE upon requestl different inlet depths upon request
PURACOS/PURACHRON Small sewage treatment plants - concrete
PURACHRON - Small sewage treatment plants - concrete from 5 bis 20 inhabitants equivalents Price groupe 093
Art. No. max. IE
Inlet, outlet DN mm
Inlet depthZt m
Outlet depthAt m
Installati-on Depth
Et m
Inner Ø D or L x B m
Weight t
weight of largest part t
€ / piece125 kN
€ / piece400 kN
PURACHRON-5 5 150/100 1,10 1,15 2,85 2,00 7,9 6,8 u.r. u.r.PURACHRON-10 10 150/100 1,10 1,15 3,35 2,00 8,9 7,8 u.r. u.r.PURACHRON-15 15 150/100 1,30 1,35 3,55 2,50 12,8 11,2 u.r. u.r.PURACHRON-20 20 150/150 0,90 1,00 3,00 3,85 x
2,50 18,7 13,7 u.r. u.r.
l PURACHRON - sewage treatment plants over 20 IE and customised solutions upon requestl different inlet depths upon request
Products for sewage treatment plant maintenance Price groupe 000
Art. No. Description € / piece
KA-WA-SET1
Sewage treatment plant maintenance set consisting of:100 pcs. NH4-N test strips
1 roll indicator paper, pH 1-121 measuring cylinder, transparent
1 Imhoff funnel1 one-piece scoop, about 1200 mm long
u.r.
WARTUNGSBUCH-K Maintenance manual for sewage treatment plants u.r.
Design and workmanship con-
forming to ÖNORM B2502
INSPECTION and MAINTENANCE: Ask for our maintenance service offers!
Sew
age t
reat
men
t plan
ts
6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURACOS - small sewage treatment plants from 5 up to 100 inhabitants equivalents - made of plastic consisting of primary sedimentation basin, activated sludge tank and sedimentation/circulation basin, with walk-on top
Price groupe 093
Art. No. max. IE
Inlet, outlet DN mm
Inlet depthZt m
Outlet depthAt m
Installati-on Depth
Et m
L x B (outside)
m
Weight t € / piece
PURACOS-5K 5 150/100 0,75 0,85 2,50 2,16 x 1,50 0,70 u.r.PURACOS-10K 10 150/100 0,75 0,85 2,50 2,16 x 2,00 1,00 u.r.PURACOS-15K 15 150/100 0,75 0,85 3,00 2,16 x 2,00 1,15 u.r.PURACOS-20K 20 150/150 0,75 0,85 3,00 2,50 x 2,16 1,50 u.r.PURACOS-30K 30 150/150 0,75 0,85 3,00 3,50 x 2,16 1,75 u.r.PURACOS-40K 40 150/150 0,75 0,85 3,00 4,00 x 2,16 2,00 u.r.PURACOS-50K 50 150/150 0,75 0,85 3,50 4,00 x 2,16 2,30 u.r.PURACOS-65K 65 150/150 0,75 0,85 3,50 5,00 x 2,16 2,50 u.r.PURACOS-80K 80 150/150 0,75 0,85 3,50 6,00 x 2,16 2,80 u.r.PURACOS-100K 100 150/150 0,75 0,85 3,50 7,00 x 2,16 3,00 u.r.l PURACOS - sewage treatment plants over 100 inh. upon requestl different inlet depths upon request
PURACOS/PURACHRON Small sewage treatment plants - plastic
PURACHRON - small sewage treatment plants from 5 up to 20 inhabitants equivalents - made of plasticwith walk-on top
Price groupe 093
Art. No. max. IE
Inlet, outlet DN mm
Inlet depthZt m
Outlet depthAt m
Installation DepthEt m
L x B m(outside)
m
Weight t € / piece
PURACHRON-5K 5 150/100 0,60 0,70 2,50 2,00 x 2,00 0,70 u.r.PURACHRON-10K 10 150/100 0,60 0,70 2,50 2,16 x 2,20 1,20 u.r.PURACHRON-15K 15 150/100 0,60 0,70 3,00 2,50 x 2,16 1,70 u.r.PURACHRON-20K 20 150/150 0,60 0,70 3,00 3,00 x 2,16 2,00 u.r.l PURACHRON - sewage treatment plants over 20 inh. and customised solutions upon requestl different inlet depths upon request
Design and workmanship con-
forming to ÖNORM B2502
INSPECTION and MAINTENANCE: Ask for our maintenance service offers!
Mine
ral o
il sep
arat
or
6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURATOP Mineral oil separator
PURATOP Series SBK mineral oil separatorDesigned with leak-proofness factor fd = 1.0 ß Price group 097
Art. No. NS Sludge trap m³
Inner ØD m
Inlet, OutletDNmm
Inlet depthZt m
Outlet depthAt m
Insertion depth Et m
Total weight
t
weight of largest part
t
€ / piece125 kN
€ / piece400 kN
SBK-3-0,65 3 0,80 1,20 150 0,72 0,74 2,13 2,8 2,1 u.r. u.r.SBK-6-2,50 6 2,80 2,00 150 0,56 0,58 2,12 6,3 4,5 u.r. u.r.SBK-6-5,00 6 5,00 2,00 150 0,56 0,58 2,82 7,6 5,7 u.r. u.r.SBK-10-2,50 10 2,70 2,00 150 0,73 0,75 2,25 6,6 4,5 u.r. u.r.SBK-10-5,00 10 5,00 2,00 150 0,73 0,75 2,95 7,9 5,8 u.r. u.r.SBK-15-3,00 15 3,80 2,00 200 0,78 0,80 2,95 7,9 5,8 u.r. u.r.SBK-15-5,00 15 5,80 2,50 200 0,77 0,79 2,95 10,8 7,8 u.r. u.r.SBK-20-5,00 20 5,80 2,50 200 0,77 0,79 2,95 10,8 7,8 u.r. u.r.ß given an assumed density of the liquid to be separated of 0,85-0,90 kg/dm³
Tested and registered according to
revised ÖNORM B5101/EN858
as amended 1 Sept. 2003
PURATOP Series SK mineral oil separatorDesigned with leak-proofness factor fd = 1,5 ß Price group 097
Art. No. NS Sludge trap m³
Inner ØD m
Inlet, OutletDNmm
Inlet depthZt m
Outlet depthAt m
Insertion depth Et m
Total weight
t
weight of largest part
t€ / piece125 kN
€ / piece400 kN
SK-3-0,65 3 0,92 1,20 150 0,72 0,74 2,13 2,8 2,1 u.r. u.r.SK-6-2,50 6 2,70 1,50 150 0,56 0,58 2,72 4,7 3,6 u.r. u.r.SK-6-5,00 6 5,15 2,00 150 0,56 0,58 2,82 7,6 5,7 u.r. u.r.SK-10-2,50 10 2,70 1,50 150 0,56 0,58 2,72 4,7 3,6 u.r. u.r.SK-10-5,00 10 5,15 2,00 150 0,56 0,58 2,82 7,6 5,7 u.r. u.r.SK-15-3,00 15 3,30 2,00 200 0,78 0,80 2,45 6,7 4,7 u.r. u.r.SK-15-5,00 15 6,40 2,00 200 0,78 0,80 2,95 7,7 5,7 u.r. u.r.SK-20-5,00 20 6,40 2,00 200 0,78 0,80 2,95 7,7 5,7 u.r. u.r.ß given an assumed density of the liquid to be separated of 0,85-0,90 kg/dm³, Systems larger than NS 20 or customised solutions upon request
dip pipe inlet
sampling opening
seperator chamber
automatic locking system
coalescing filter
sludge trap
dip pipe inlet
sampling opening
seperator chamber
automatic locking system
coalescing filter
sludge trap
Mine
ral o
il sep
arat
or
6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURATOP mineral oil separator
PURATOP PT mineral oil seperator Price group 097
Sludge trap Seperator
Art. No. NSInlet/Outlet
DN mm
Inlet depthZt m
Outlet depthAt m
Insertion depth
Et1 m
Inner ØD m
Volm³
Insertion depth
Et2 m
Inner ØD m
Total weight
t
weight of largest part t
€ / piece
PT-30-2-6,0 30 250 0,85 0,89 2,47 2,5 7,25 2,00 1,50 13,9 6,5 u.r.
PT-40-2-8,0 40 300 0,91 0,95 3,00 2,5 9,56 3,00 2,00 18,7 7,4 u.r.
PT-50-2-10 50 300 0,88 0,92 2,97 2,5 9,56 2,13 2,00 16,8 7,4 u.r.
PT-65-2-13 65 300 0,88 0,92 2,61 2,5 x 4,65 15,9 2,13 2,00 26,6 14,3 u.r.
PT-80-2-16 80 400 1,20 1,22 2,84 2,5 x 5,75 19,3 2,84 2,00 32,4 17,2 u.r.
PT-100-2-20 100 400 1,20 1,22 2,84 2,5 x 5,75 19,3 2,84 2,50 36,2 17,2 u.r.
Tested and registered according to
revised ÖNORM B5101/EN858
as amended 1 Sept. 2003
Mine
ral o
il sep
arat
or
6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOPUR mineral oil separatorwith self-cleaning inclined plate packs Price group 097
Art. No. NS Sludge trap m³
Inlet, OutletDNmm
Inner Ø D bzw. L x B
m
Inlet depthZt m
OutletdepthAt m
Insertion depth Et m
Total weight
t
weight of largest part
t
€ / piece125 kN
€ / piece400 kN
ECOPUR-3 3 2,16 150 1,50 0,59 0,69 2,34 4,7 3,2 u.r. u.r.ECOPUR-4,5P 4,5 4,36 150 2,00 0,70 0,80 2,45 6,8 4,6 u.r. u.r.ECOPUR-6 6 4,36 150 2,00 0,70 0,80 2,45 6,8 4,6 u.r. u.r.ECOPUR-7,5P 7,5 7,13 150 2,50 0,70 0,80 2,45 10,2 6,9 u.r. u.r.ECOPUR-7,5L 7,5 9,62 150 2,50 0,70 0,80 2,95 11,1 7,8 u.r. u.r.ECOPUR-9 9 6,23 200 2,50 0,75 0,85 2,45 10,2 6,9 u.r. u.r.ECOPUR-12 12 10,78 200 3,60 x 2,50 0,80 0,90 2,60 17,9 12,5 u.r. u.r.ECOPUR-12L 12 10,78 200 3,60 x 2,50 0,80 0,90 2,60 17,9 12,5 u.r. u.r.ECOPUR-14 14 10,78 200 3,60 x 2,50 0,80 0,90 2,60 17,9 12,5 u.r. u.r.ECOPUR-16 16 15,50 200 4,65 x 2,50 0,80 0,90 2,60 20,9 15,3 u.r. u.r.l different inlet depths upon request
from NS 12 from NS 12, also available as 2-tank systems
ÖNORM B 5101 tested!
Version 1990
l PHASE-OUT MODEL
Accessory products Price group 000
Art. No. Description € / piece
Wassernachweispaste Water indicating paste, tube á 150 g u.r.Deckelausheber Titanium-alu cover lifter u.r.Wartungsbuch-MOEA Maintenance manual u.r.
Training provided when mineral oil separator is taken into operation upon request
INSPECTION and MAINTENANCE: Ask for our maintenance service offers!
Single-tank systems
ECOPUR mineral oil separator
Mine
ral o
il sep
arat
or
66
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ADD-ON COALESCING KITSfor installation in existing mineral oil separatorsl NOTE: inspect the system before installation of add-on kit
Concrete SURFACE RUN-OFF PURIFICATION SYSTEM
CRITERIA according to standard ÖNORM B 5102
• Surface and capacity of sludge trap• Purification efficiency analogous to separation class I• Hydraulic performance
WATER PROTECTION SYSTEMSProject-based upon request
Series VSS-PT with sludge trap Price group 097
Sludge trap Seperator
Art. No. NSInlet/
Outlet DN mm
Inlet depthZt m
Outlet depthAt m
Insertion depth
Et1 m
Inner ØD m
Volm³
Insertion depth
Et2 m
Inner ØD m
Total weight
t
weight of largest part t
€ / piece
VSS-PT-20-1 20 200 0,78 0,80 - - 3,3 2,45 2,00 6,4 4,7 u.r.
VSS-PT-30-2 40 250 0,85 0,89 2,00 2,0 3,2 3,00 1,50 9,8 4,0 u.r.
VSS-PT-45-2 50 300 0,88 0,92 1,97 2,5 4,7 2,13 2,00 14,4 5,2 u.r.
VSS-PT-65-2 65 300 0,88 0,92 2,60 2,5 x 3,60 11,9 2,13 2,00 24,1 11,5 u.r.
VSS-PT-80-2 80 400 1,20 1,22 2,84 2,5 x 4,65 15,3 2,84 2,00 29,0 16,4 u.r.
VSS-PT-100-2 100 400 1,20 1,22 2,84 2,5 x 4,65 15,3 2,84 2,50 32,0 16,4 u.r.
* Sludge trap is integrated with model NS 20; given an assumed density of rain of 150l/s-hal different inlet depths upon request, all products available for class 125 kN and 400 kN
conforms ÖN B5102 1.12.2004
EN 858 tested!
Surface run-off purification systems for vehicular traffic and parking areas are prefabricated systems retaining solids, settlable particles and, if present, mineral oil from surface run-off. As a rule, maintenance, repair work, fuel filling or washing activities are not carried out on such areas.
Mine
ral o
il sep
arat
or
6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Stainless steel sludge traps
Stainless steel sludge traps for mineral oil separatorsMaterial 1.4571 Price group 097
Art. No. NSSludge trap
capacitym³
Inlet, OutletDNmm
Diameter D m
Inlet depthZt m
Outlet depthAt m
Insertion depth Et m
Weightt € / piece
Installation in the ground (125 kN)96.03.12 1,5/3 0,65 100 1,13 0,44-1,17 0,47-1,20 1,15-1,88 0,17 u.r.96.06.12 6/10 2,50 150 1,60 0,36-1,17 0,39-1,20 1,67-2,48 0,29 u.r.
Art. No. NSSludge trap
contendm³
Inlet, OutletDNmm
Diameter D m
Inlet depthZt m
Outlet depthAt m
HeightH m
Weightt € / piece
Free-Standing96.03.08 1,5/3 0,65 100 1,13 0,68 0,65 1,06 0,15 u.r.96.06.08 6/10 2,50 150 1,60 1,25 1,25 1,52 0,26 u.r.
Installation in the ground Free-standing
Stainless steel mineral oil separatorsMaterial 1.4571 Price group 097
Art. No. NS Inlet, OutletDN mm
DiameterD m
Inlet depthZt m
Outlet depthAt m
Insertion depth Et m
Weightt € / piece
Installation in the ground (125 kN)94.03.12 1,5/3 100 0,65 0,47-1,20 0,50-1,23 1,15-1,88 0,17 u.r.94.10.12 6/10 150 0,96 0,39-1,20 0,42-1,23 1,67-2,48 0,24 u.r.
Art. No. NS Inlet, OutletDN mm
Diameter D m
Inlet depthZt m
Outlet depthAt m
HeightH m
Weightt € / piece
Free-standing94.03.08 1,5/3 100 0,65 0,65 0,62 1,06 0,14 u.r.94.10.08 6/10 150 0,96 1,25 1,22 1,52 0,21 u.r.
Installation in the ground Free-standing
Stainless steel mineral oil separators
Mine
ral o
il sep
arat
or
6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Plastic mineral oil separators
system diagramExample: Free-standing with integrated pump
Special solutions
Mineral oil separator with integrated plastic sludge trap made of plasticCover 125 kN Price group 000
Art. No. NSSludge trap
capacitym³
Inlet, OutletDNmm
Diameter D m
Inlet depthZt m
Outlet depthAt m
Insertion depth Et m
Weightt € / piece
SEP-PE-0,3 0,3 0,12 100 0,75 0,33-0,63 0,36-0,66 1,14-1,44 0,14 u.r.l different NS and covers upon request
Grey cast iron mineral oil separatorwith exchangeable coalescence insert conforming to DIN 1999 Parts 4-6 (not tested to ÖNORM B 5101) cover 125kN Price group 097
Art. No. NSInlet, Outlet
DNmm
Dimensions a x b m
Inlet depthZt m
Outlet depthAt m
Insertion depth Et m
Total weight t
€ / piece400 kN
140-6701-11-30 1,5 100 0,82 x 0,32 0,23 0,26 0,60 0,11 u.r.140-6711-11-30 1,5 100 0,82 x 0,32 0,49 0,51 0,85 0,15 u.r.140-6721-11-30 1,5 100 0,82 x 0,32 0,80 0,82 1,16 0,20 u.r.140-6703-11-30 3 100 1,05 x 0,42 0,23 0,26 0,74 0,22 u.r.140-6753-11-30 3 100 1,05 x 0,42 0,41 0,43 0,91 0,25 u.r.140-6713-11-30 3 100 1,05 x 0,42 0,62 0,64 1,12 0,30 u.r.140-6756-11-30 6 150 1,26 x 0,42 0,44 0,47 0,98 0,33 u.r.140-6716-11-30 6 150 1,26 x 0,42 0,65 0,68 1,19 0,38 u.r.140-6726-11-30 6 150 1,26 x 0,42 0,86 0,89 1,40 0,42 u.r.
Grey cast iron mineral oil separator
Inlet Outlet
Mine
ral o
il sep
arat
or
6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Oil binding agents
Oil binding agents Price group 000
Art. No. DescriptionLoose unit
weightg/l
Oil absorption per packing
unitPacking unit € / piece
EKOPERL-33 Oil-binding agent for use on dry and solidground and on bodies of water 90 25-30 Bag á 100 l
(= approx. 9 kg) u.r.
EKOPERL-OELBINDEWUER Oil-binding cubes:Oil-binding agent for use on bodies of water 180 30-40 Bag á 80 l
(= approx. 12 kg) u.r.
EKOPERL-OELBINDESCHL Oil-binding hose:Oil-binding agent for use on bodies of water - - Schlauch
á 3m u.r.
EKOPERL-66 Special oil-binding agent for use on bodies of water 120 30-35 Bag á 100 l (= approx. 12 kg) u.r.
TERRAPERL-S heavy-duty universal absorption agent for use ondry and solid ground 490 17 Bag á 40 l
(= approx. 20 kg) u.r.
TERRAPERL-S-NOVA/F-34Oil- and chemicals binding agent for use on
solid, dry groundgrain size 0,25 - 1,8 mm
425 19-25 Bag á 34,1 l (= approx. 14,5 kg) u.r.
TERRAPERL-S-NOVA-G38Oil- and chemicals binding agent for use on
solid, dry groundgrain size 1,8 - 3,5 mm
330 approx. 15 Bag á 37,9 l (= approx. 12,5 kg) u.r.
BIOREG-UNIVERSAL Universal binding agent for oil & chemicalsnatural product Type II/R 200 approx. 28 Bag á 50 l
(= approx. 10,0 kg) u.r.
BIOREG-ABSORBER Heavy binding agent for oil & chemicalsType III/R 585 9,6 Bag á 20 l
(= approx. 12,0 kg) u.r.
BIOREG-CLEANER Purificatoin concentrate for degreasingof trafficked areas - - 10 l can u.r.
Mine
ral o
il sep
arat
or
�0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
OilSET WARNING SYSTEM
This device alerts the user to the need to remove oil, petrol or grease from the separator. This prevents the unnecessary release of hydrocarbon emissions into the sewer system.
Control unit and probe approved under ATEX Directive 94/9/EC.
OilSET-2000 Warning system for oil, petrol and grease separator with two probesOilSET-2000 signals full oil chamber and high level of sludge in the separator. This prevents the unnecessary release of hydrocar-bon emissions as well as sludge emission into the sewer system.
Control unit and probe approved under ATEX Directive 94/9/EC.
Oilset Warning System Price group 000Art. No. Description € / piece
SE10001E/PUR OilSET-1000 warning system for oil, petrol and grease separator u.r.SE10081E/PUR OilSET-2000 warning system for oil, petrol and grease separator and measuring sludge level u.r.
Specifications, control unit OilSET 1000Outputs: Two relays, floating changeover contact, 250
V AC 5 A. One relay (alarm relay) acknowled-geable. In case of an alarm, the relays switch off. Acknowledgeable buzzer and LED displays indicate supply voltage, short-circuits and ruptures in the wiring.
Probes: A conductive SET DM/3, ultrasound probe SET/S or capacitive SET/…2.
Housing: IP 65, 175 x 125 x 75 mm (BxHxT), Polycarbonat
Probe cables: Screened instrument cable
Ex-conformity certificate: EX II(1) G, [EEx ia] II C, VTT 04 ATEX 031X
Specifications, ProbesSET DM3, for oil, petrol and grease separatorsOperating principle: Conductive
Application: Detects full oil or grease chamber in the separator
Conformity certification: EX II(1) G, EEx ia IIA T4, VTT 02 ATEX 012X
Specifications, control unit OilSET 2000Outputs: Two relays, floating changeover contact, 250 V
AC 5 A.In case of an alarm, the relays switch off. Acknowledgeable buzzer and LED displays indicate supply voltage, short-circuits and ruptures in the probe wiring.
Probes: Two capacitive SET/…2 probes, SET DM/3or SET/S.
Housing: IP 65, 175 x 125 x 75 mm (BxHxT), Polycarbonat
Probe cables: Screened instrument cable
Ex-conformity certificate: EX II(1) G, [EEx ia] II C, VTT 04 ATEX 031X
Specifications, ProbesSET S for sludge detectionOperating principle: Ultrasound
Application: Detects sand and sludge
Conformity certification: EX II(1) G, EEx ia IIB T5, VTT 03 ATEX 007X
OilSET-1000 warning system for oil, petrol and grease separator
control unit
Oil
Water
Sludge
Mine
ral o
il sep
arat
or
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Concrete sludge traps
Concrete sludge trapscompact design Price group 094
Art. No. Capacity m³
Inlet, OutletDNmm
Inner Ø D bzw. L x B
m
Wall thick-ness s
cm
Inlet depthZt m
OutletdepthAt m
Insertion depth Et m
Total weight
t
weight of largest part
t
€ / piece125 kN
€ / piece400 kN
SF-15-2,8-150 2,8 150 1,50 10 0,65 0,75 2,40 4,3 3,1 u.r. u.r.SF-15-2,8-200 2,8 200 1,50 10 0,69 0,79 2,40 4,3 3,1 u.r. u.r.SF-15-2,8-250 2,8 250 1,50 10 0,74 0,84 2,40 4,3 3,1 u.r. u.r.
SF-20-5,0-150 5,00 150 2,00 10 0,70 0,80 2,45 6,6 4,7 u.r. u.r.SF-20-5,0-200 5,00 200 2,00 10 0,74 0,84 2,45 6,6 4,7 u.r. u.r.SF-20-5,0-250 5,00 250 2,00 10 0,79 0,89 2,45 6,6 4,7 u.r. u.r.
SF-25-7,5-150 7,5 150 2,50 12 0,70 0,80 2,45 9,5 6,5 u.r. u.r.SF-25-7,5-200 7,5 200 2,50 12 0,74 0,84 2,45 9,5 6,5 u.r. u.r.SF-25-7,5-250 7,5 250 2,50 12 0,79 0,89 2,45 9,5 6,5 u.r. u.r.
SF-25-10,0-150 10,0 150 2,50 12 0,70 0,80 2,95 10,4 7,4 u.r. u.r.SF-25-10,0-200 10,0 200 2,50 12 0,74 0,84 2,95 10,4 7,4 u.r. u.r.SF-25-10,0-250 10,0 250 2,50 12 0,79 0,89 2,95 10,4 7,4 u.r. u.r.
SF-25-12,5-150 12,5 150 2,50 12 0,70 0,75 3,45 11,4 8,4 u.r. u.r.SF-25-12,5-200 12,5 200 2,50 12 0,74 0,79 3,45 11,4 8,4 u.r. u.r.SF-25-12,5-250 12,5 250 2,50 12 0,79 0,84 3,45 11,4 8,4 u.r. u.r.
SF-390-12,1-150 12,1 150 3,60 x 2,50 15 0,76 0,86 2,60 16,2 11,6 u.r. u.r.SF-390-12,1-200 12,1 200 3,60 x 2,50 15 0,80 0,90 2,60 16,2 11,6 u.r. u.r.SF-390-12,1-250 12,1 250 3,60 x 2,50 15 0,85 0,95 2,60 16,2 11,6 u.r. u.r.
SF-495-16,4-150 16,40 150 4,65 x 2,50 15 0,76 0,86 2,60 20,4 14,3 u.r. u.r.SF-495-16,4-200 16,40 200 4,65 x 2,50 15 0,80 0,90 2,60 20,4 14,3 u.r. u.r.SF-495-16,4-250 16,40 250 4,65 x 2,50 15 0,85 0,95 2,60 20,4 14,3 u.r. u.r.
SF-605-20,8-150 20,80 150 5,75 x 2,50 15 0,76 0,86 2,60 24,6 17,2 u.r. u.r.SF-605-20,8-200 20,80 200 5,75 x 2,50 15 0,80 0,90 2,60 24,6 17,2 u.r. u.r.SF-605-20,8-250 20,80 250 5,75 x 2,50 15 0,85 0,95 2,60 24,6 17,2 u.r. u.r.l different inlet depths upon request
Mine
ral o
il sep
arat
or
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Concrete sampling shafts
Concrete sampling shaftscompact design, without/with sampling pit Price group 092
Art. No. Inner Ø D m
Wall thick-ness s
cm
Inlet depthZt m
Outlet depthAt m
Insertion depth Et m
nominal diameter DN mm
Total weight
t
weight of largest part
t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
without sampling pitPE-100-100-OM 1,00 8 1,04 1,24 1,32 100 0,97 0,53 u.r. u.r. u.r.PE-100-150-OM 1,00 8 1,04 1,24 1,32 150 0,97 0,53 u.r. u.r. u.r.PE-100-200-OM 1,00 8 1,04 1,24 1,32 200 0,97 0,53 u.r. u.r. u.r.PE-100-250-OM 1,00 8 1,04 1,24 1,32 250 0,97 0,53 u.r. u.r. u.r.with sampling pitPE-100-100 1,00 8 1,04 1,09 1,32 100 1,17 0,72 u.r. u.r. u.r.PE-100-150 1,00 8 1,04 1,09 1,32 150 1,17 0,72 u.r. u.r. u.r.PE-100-200 1,00 8 1,04 1,09 1,32 200 1,17 0,72 u.r. u.r. u.r.PE-100-250 1,00 8 1,04 1,09 1,32 250 1,17 0,72 u.r. u.r. u.r.l different inlet depths upon request, special designs upon request
Art. No. Inner Ø D m
Wall thick-ness s
cm
Inlet depthZt m
Outlet depthAt m
Insertion depth Et m
nominal diameter DN mm
Total weight
t
weight of largest part
t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
PE-60-100-OM 0,60 8 0,46 0,66 0,78 100 0,41 0,28 u.r. u.r. u.r.PE-60-150-OM 0,60 8 0,46 0,66 0,78 150 0,41 0,28 u.r. u.r. u.r.l different inlet depths upon request, special designs upon request
Mine
ral o
il sep
arat
or
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PUROZON - recycling systems
PUROZON is employed wherever process water is highly contaminated with organic or chemicalpollutants and treatment is required.
Range of application
Example of applications • washing water recycling systems• (single washing stations/drive-through car washes)• Engine cleaning• Retrofitting of mineral oil separators• Effluents of disposal plants• Effluents of painting shops• Effluents of printing shops• Effluents of wood and pulp mills• Effluents of automobile industry (components factories)• Landfill leachate• Waste air scrubbers
Advantages • water consumption reduced by 95%• Consumption of cleaning agents reduced by 50%• No need for connection to sewer• No generation of hazardous waste• No problem with road salt contamination in winter• Suitable for retrofitting – expandable due to modular design• Every system is planned, designed and built to meet specific customer needs
Special features Even heavily polluted water carrying stable emulsions, including effluents from components cleaning, canbe discharged into the circuit without problems and purified. Unlike conventional gravity separators, which retain only non-dissolved hydrocarbons, this type of waste water purification also removes dissolved hydrocarbons from cleaning agents, anti-freeze agents, brake fluids, and cleaner solvent.
The waste product is inert material which, in contrast to waste water purification systems operatingwith cracking chemicals, is not hazardous waste and can therefore easily be disposed of.
Washing water treatment plant(example of application)
CAR WASH
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOLIP concrete grease separatorInstallation in the ground
Type ECOLIP-Bwith partition wall and integrated sludge trap; discharge through service openings
Price group 097
Art. No. NS Sludge trap m³
Inlet, Outlet DNmm
Inner Ø Dbzw. L x B
m
Wall thick-nesss
cm
Inlet depthZt m
Outlet depthAt m
Insertion depthEt m
Total weight
t
weight of largest part
t
€ / piece125 kN
€ / piece400 kN
FA-2-12-0,3 2 0,3 150 1,20 10 0,77 0,82 2,07 3,0 2,5 u.r. u.r.FA-4-15-0,5 4 0,5 150 1,50 10 0,63 0,68 1,88 4,1 3,0 u.r. u.r.FA-7-20-0,7 7 0,7 150 2,00 10 0,64 0,69 1,89 6,6 4,6 u.r. u.r.FA-9-20-0,9 9 0,9 150 2,00 10 0,64 0,69 2,19 7,1 5,2 u.r. u.r.FA-12-25-1,2 12 1,2 200 2,50 12 0,69 0,74 1,89 9,5 6,6 u.r. u.r.FA-15-25-1,5 15 1,5 200 2,50 12 0,69 0,74 2,19 10,2 7,3 u.r. u.r.FA-22-390-2,2 22 2,2 250 3,60 x 2,50 15 0,86 0,91 2,66 17,3 12,7 u.r. u.r.FA-30-495-3,0 30 3,0 300 4,65 x 2,50 15 0,91 0,96 2,66 21,5 15,4 u.r. u.r.FA-38-605-3,8 38 3,8 300 5,75 x 2,50 15 0,91 0,96 2,66 25,7 18,3 u.r. u.r.
Type ECOLIP-B-ENconforms to ÖN/EN 1825 with integrated Sludge trap; discharge through service openings
Price group 097
Art. No. NS Sludge trap m³
Inlet, Outlet DNmm
Inner Ø Dbzw. L x B
m
Wall thick-nesss
cm
Inlet depthZt m
Outlet depthAt m
Insertion depthEt m
Total weight
t
weight of largest part
t
€ / piece125 kN
€ / piece400 kN
FAKON-2-10 2 0,2 100 1,00 10 0,95 1,02 2,25 2,0 1,5 u.r. u.r.FA-4-12ä 4 0,4 100 1,20 10 0,50 0,57 2,05 2,7 2,1 u.r. u.r.FAKON-7-15 7 0,7 150 1,50 10 0,95 1,02 2,70 3,8 3,1 u.r. u.r.FAKON-10-20 10 1,0 200 2,00 10 1,07 1,14 2,57 5,3 4,2 u.r. u.r.FAKON-15-25 15 1,5 200 2,50 12 1,31 1,38 2,81 7,7 6,0 u.r. u.r.FAKON-20-25 20 2,0 200 2,50 12 1,31 1,38 3,01 8,2 6,5 u.r. u.r.ä available only with flat topl Special models upon request
l Special model: with plate tops (reduced insertion depth) and/or special sampling pipe (integrated into the effluent pipe) upon request
Note: The standard calls for a vent lineabove the roof!
OutletInlet OutletInlet
OutletInlet
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Concrete sampling shaftcompact design, without sampling pit Price group 092
Art. No. Inner Ø D m
Wall thick-nesss
cm
Inlet depthZt m
Outlet depthAt m
Insertion depthEt m
Nominal Diameter DN mm
Weight t
Weight of largest
part t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
PE-100-100-OM 1,00 8 1,04 1,24 1,32 100 0,97 0,53 u.r. u.r. u.r.PE-100-150-OM 1,00 8 1,04 1,24 1,32 150 0,97 0,53 u.r. u.r. u.r.PE-100-200-OM 1,00 8 1,04 1,24 1,32 200 0,97 0,53 u.r. u.r. u.r.PE-100-250-OM 1,00 8 1,04 1,24 1,32 250 0,97 0,53 u.r. u.r. u.r.l Special model upon request
ECOLIP concrete grease separator
Concrete sampling shaftcompact design, without sampling pit Price group 092
Art. No. Inner Ø D m
Wall thick-nesss
cm
Inlet depthZt m
Outlet depthAt m
Insertion depthEt m
Nominal Diameter DN mm
Weight t
Weight of
largest part t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
PE-60-100-OM 0,60 8 0,46 0,66 0,78 100 0,41 0,28 u.r. u.r. u.r.PE-60-150-OM 0,60 8 0,46 0,66 0,78 150 0,41 0,28 u.r. u.r. u.r.l Special model upon request
Sampling pipe can be integratedfor optional use with ECOLIP-B concrete grease separator
Grea
se se
para
tors
�6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type ECOLIP-K Mobil 1made of PE-HD, with integrated Sludge trap, discharge through service openings
Price group 092
Art. No. Description € / piece
46.00.00 ECOLIP-K Mobil 1 u.r.89.50.51 4 wheels with locks u.r.
wheels with locks
Type ECOLIP-K Mobil 2 conforms DIN 4040/ÖNORM EN 1825made of PE-HD, with integrated Sludge trap, discharge through service openings
Price group 092
Art. No. Description € / piece
92.200 sludge trap capacity: 60 lgrease separator cap.: 150 l
weight: 45 kgu.r.
917.700 Trolley u.r.
Img. shows Type 0,5� Inlet� Outlet� Sludge trap� Separator chamber� Snap-close lid
ECOLIP (PE-HD) plastic grease separator NS 2 - NS 7Free-standing
Support frame
Driving facility
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOLIP (PE-HD) plastic grease separator NS 2 - NS 7Free-standing
Type ECOLIP-K Chromtech G ova conforms ÖNORM EN 1825with integrated Sludge trap, without partition wall, discharge through service openings
Price group 095
NS 2Basic model
Art. No.(note direction of flow) DN outside Ø mm Base Inlet
mmBase Outlet
mm € / piece
Cap. ST: 200 LiterCap. GS: 730 Liter
right 42.02.01100 110 1000 930 u.r.
left 42.02.02
NS 4Basic model
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 400 LiterCap. GS: 960 Liter
right 42.04.01100 110 1060 990 u.r.
left 42.04.02
NS 7Basic model
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 700 LiterCap. GS: 1270 Liter
right 42.07.01150 160 1040 970 u.r.
left 42.07.02
l Special model or different NS‘s upon request
DN 70 suction pipe with DIN flange at the end only with series42.22.51-42.30.52
Inspection window with wiper (optional)
Ventilation connection outside
OutletInlet
filling unit (optional)
DN 70 suction pipe with DIN flange at the end only with series42.22.51-42.30.52
Inspection window with wiper (optional)
Ventilation connection Ø 110 outside
OutletInlet
filling unit (optional)
DN 70 suction pipe with DIN flange at the end only with series42.22.51-42.30.52
Inspection window with wiper (optional)
Ventilation connection
OutletInlet
filling unit (optional)outside
l images show right flow cover with seal and tension ring
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOLIP (PE-HD) plastic grease separator NS 2 - NS 7Free-standing
Absuction pipe angeflanscht DN100 Höhe bis Oberkante Fettabscheider am Ende Bördel-Flansch ND 10 DIN 2642
Type ECOLIP-K Chromtech D ova conforms ÖNORM EN 1825with integrated sludge trap, without partition wall, discharge via direct discharge connection DN 100 PN 10
Price group 095
NS 2suction pipe
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 200 LiterCap. GS: 730 Liter
right 42.22.01100 110 1290 1220 u.r.
left 42.22.02
NS 4Suction pipe
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 400 LiterCap. GS: 960 Liter
right 42.24.01100 110 1350 1280 u.r.
left 42.24.02
NS 7Suction pipe
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 700 LiterCap. GS: 1270 Liter
right 42.27.01150 160 1330 1260 u.r.
left 42.27.02
l Special model or different NS‘s upon request
Ventilation connection Ø 110 outside
OutletInlet
filling unit (optional)
motor-driven mixer (optional)
Suction pipe DN 100 flange-mounted rises up to top edge of grease separator, termi-nates in flare flange ND 10 DIN 2642
Inspection window with wiper (optional)
Outlet
Suction pipe DN 100 flange-mounted rises up to top edge of grease separator, termi-nates in flare flange ND 10 DIN 2642
Inspection window with wiper (optional)Ventilation connection Ø 110 outside
Inlet
filling unit (optional)
motor-driven mixer (optional)
Optional against extra charge:Inspection window, motor-driven mixer, filling unit
Inspection window with wiper (optional)
Ventilation connection Ø 110 outside
OutletInlet
filling unit (optional)
motor-driven mixer (optional)
l images show right flow cover with seal and tension ring
Suction pipe DN 100 flange-mounted rises up to top edge of grease separator, termi-nates in flare flange ND 10 DIN 2642
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOLIP (PE-HD) plastic grease separator NS 2 - NS 7Free-standing
Type ECOLIP-K Chromtech A ova conforms ÖNORM EN 1825with integrated sludge trap, without partition wall, discharge via manually controlled discharge device, homogenisation by mixer(s), discharge connection R 2 1/2“ outside thread PN 10
Price group 095
NS 2Semiautomatic
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 200 LiterCap. GS: 730 Liter
right 42.52.01100 110 1290 1220 u.r.
left 42.52.02
NS 4Semiautomatic
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 400 LiterCap. GS: 960 Liter
right 42.54.01100 110 1350 1280 u.r.
left 42.54.02
NS 7Semiautomatic
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 700 LiterCap. GS: 1270 Liter
right 42.57.01150 160 1330 1260 u.r.
left 42.57.02
l Special model or different NS‘s upon request
l images show right flow cover with seal and tension ring
Pump flange-mounted with discharge pipe rising totop edge of grease separator terminating with 2 1/2“ thread
Inspection window with wiper
Ventilation connection Ø 110 outsideOutlet
Inlet
Filling unit
Motor-driven mixer
Ventilation connection Ø 110 outsideOutlet
Inlet
Filling unit
Motor-driven mixerPump flange-mounted with discharge pipe rising totop edge of grease separator terminating with 2 1/2“ thread
Inspection window with wiper
Pump flange-mounted with discharge pipe rising totop edge of grease separator terminating with 2 1/2“ thread
Inspection window with wiper
Ventilation connection Ø 110 outsideOutlet
Inlet
Filling unit
Motor-driven mixer
Grea
se se
para
tors
�0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOLIP (PE-HD) plastic grease separator NS 2 - NS 7Free-standing
Type ECOLIP-K Chromtech VA ova conforms ÖNORM EN 1825with integrated sludge trap, without partition wall, discharge via program-controlled discharge devicedischarge connection R 2 1/2“ outside thread PN 10
Price group 095
NS 2Fully automatic
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 200 LiterCap. GS: 730 Liter
right 42.72.01100 110 1290 1220 u.r.
left 42.72.02
NS 4Fully automatic
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 400 LiterCap. GS: 960 Liter
right 42.74.01100 110 1350 1280 u.r.
left 42.74.02
NS 7Fully automatic
Art. No.(note direction of flow) DN Ø outside mm Base Inlet mm Base Outlet mm € / piece
Cap. ST: 700 LiterCap. GS: 1270 Liter
right 42.77.01150 160 1330 1260 u.r.
left 42.77.02
l Special model or different NS‘s upon request
Motor-driven mixer
l images show right flow cover with seal and tension ring
Pump flange-mounted with discharge pipe rising totop edge of grease separator termi-nating with 2 1/2“ thread outside
Inspection window with wiper
Ventilation connection Ø 110 outsideOutlet
Inlet
Filling unit
Pressure cell
Pump flange-mounted with discharge pipe rising totop edge of grease separator terminating with 2 1/2“ thread outside
Inspection window with wiper
Ventilation connection Ø 110 outsideOutlet
Inlet
Filling unit
Motor-driven mixer Pressure cell
Pump flange-mounted with discharge pipe rising totop edge of grease separator terminating with 2 1/2“ thread outside
Inspection window with wiper
Ventilation connection Ø 110 outsideOutlet
Inlet
Filling unit
Motor-driven mixer
Pressure cell
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type ECOLIP-K E+S PV ova conforms DIN 4040/ÖNORM EN 1825with integrated sludge trap, discharge via fully automated program-controlled discharge device,Homogenisation by actuator(s), jet and conic nozzles for mixing and flushing, with externally mountedpump with integrated shredder and gate valve, discharge connection DN 65 PN 10
Price group 095
1 Inlet2 Outlet3 Sludge trap4 Grease separator chamber
5 Snap-close lid6 Inspection glass7 Dispatcher8 Actuator
9 Jet nozzle10 Conic nozzle11 Pump with gate valve
12 flushing water supply (warm water) and filling water supply (cold water)
13 Control cabinet14 Discharge connection
NS DNSpace requirement for
installation a x b b1 h h1 h2 h3Used water capacity
Weight approx. kga b Sludge trap Separator
2 100 1700 680 1080 1455 1030 1100 1180 220 l 570 l 240 kg4 100 2250 920 1320 1455 1030 1100 1180 430 l 1070 l 290 kg7 150 3180 1150 1550 1455 1030 1100 1180 720 l 1870 l 400 kg10 150 3600 1350 1750 1455 1030 1100 1180 1052 l 2480 l 440 kg
ECOLIP (PE-HD) plastic grease separator NS 2 - NS 10Free-standing
l Image shows NS 7
NS Art. No.left pump
Art. No.right ump Pump size € / piece
completely assembled€ / piece
welded on-site
2 93.222.50/P11 93.222.50/P32 93.222.00/P11 93.222.00/P32 2,6 kW u.r. u.r.4 93.224.50/P11 93.224.50/P32 93.224.00/P11 93.224.00/P32 2,6 kW u.r. u.r.7 93.227.50/P11 93.227.50/P32 93.227.00/P11 93.227.00/P32 2,6 kW u.r. u.r.
10 93.210.50/P11 93.210.50/P32 93.210.00/P11 93.210.00/P32 4,0 kW u.r. u.r.1 system completely assembled2 system welded on-site l Special model or different NS‘s upon request
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type ECOLIP-K E+S PV eck conforms DIN 4040/ÖNORM EN 1825with integrated sludge trap, discharge via fully automated program-controlled discharge device,Homogenisation by actuator(s), jet and conic nozzles for mixing and flushing, with externally mountedpump with integrated shredder and gate valve, discharge connection DN 65 PN 10
Price group 095
NS DNSpace requirement for
installation a x b b1 h h1 h2 h3 cUsed water capacity
Weight approx. kga b Sludge trap Separator
15 200 4600 1444 1930 1764 1130 1240 1380 570 1506 l 3740 l 1220 kg20 200 5520 1700 2190 1864 1230 1340 1480 695 2100 l 6201 l 1500 kg25 200 6760 1700 2190 1864 1230 1340 1480 695 2546 l 7509 l 1780 kg
ECOLIP (PE-HD) plastic grease separator NS 15 - NS 25Free-standing
NS Art. No.left pump
Art. No.right pump
€ / piececompletely assembled
€ / piecewelded on-site
15 95.415.50/P11 95.415.50/P32 95.415.00/P11 95.415.00/P32 u.r. u.r.20 95.420.50/P11 95.420.50/P32 95.420.00/P11 95.420.00/P32 u.r. u.r.25 95.425.50/P11 95.425.50/P32 95.425.00/P11 95.425.00/P32 u.r. u.r.
1 completely assembled2 welded on-site l Special model or different NS´s upon request
Image shows NS 151 Inlet2 Outlet3 Sludge trap4 Grease separator chamber5 Lid cover6 Inspection glass7 Dispatcher8 Actuator9 Jet nozzle10 Conic nozzle11 Pump with gate valve12 flushing water supply (warmwater)13 filling water supply (coldwater)14 Run-dry protection15 Control cabinet16 Discharge connection
Scope of delivery• Tank with three lid covers• Complete internal and external piping• 3 dispatchers with actuator• Long inspection glass with cleaning device• Filling devices• Pumps with gate valves removed for transport• 2 solenoid valves to be mounted by owner
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Nominal Size
Sludge trap + Grease separatormax. frost-free depth 1200 mm
Cover concrete casting Kl B 125Art. No.
ØTotal
heightmm
Height of container
mma c
DNOutside
Økg € / piece
125 kN€ / piece400 kN
NS 1Cap. ST 100 l
GS 270 l41.01.12 810 1975 1400 845 775 100
110 65 u.r. u.r.
NS 2Cap. ST 200 l
GS 550 l41.02.12 1216 2115 1570 985 915 100
110 90 u.r. u.r.
NS 4Cap. ST 400 l
GS 1060 l41.04.12 1665 2145 1665 1015 945 100
110 145 u.r. u.r.
NS 7Cap. ST 700 l
GS 1744 l41.07.12 1860 2120 1465 990 920 150
160 210 u.r. u.r.
NS 10Cap. ST 1000 l
GS 2500 l41.10.12 ST 1170
GS 1860 2170 1465 1040 970 150160 320 u.r. u.r.
NS 15Cap. ST 1560 l
GS 3800 l41.15.12 ST 1450
FS 2320 2170 1465 1040 970 200200 410 u.r. u.r.
Type ECOLIP-K Chromtech E rund conforms ÖNORM EN 1825with integrated Sludge trap, without partition wall, discharge through service openings
Price group 095
l Special model or different NS‘s upon request
ECOLIP (PE-HD) plastic grease separator NS 1 - NS 15Installation in the ground
Concrete plateBe
hälte
rhöh
e H frostf
reie
Tiefe
NS 1-7 with dome and 1 coverNS 10 - 15 with 2 tanks with 1 dome and cover each
OutletInlet
Subgrade offine sand or fresh concrete
Compacted sand layers
Crushed stone base
5cm soft layer of mineral fibressupplied by owner
Surface
Design counteracting groundwater pressure
Reinforced concrete base plate, L x W or Ø, depending on load pressure, to be designed
by a structural engineer!
Grease separator with integrated sludge trap
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOLIP Accessories
Sampling pipe made of PE-HDfor free-standing grease separator systems with closable access hole and cleaning brush to be supplied with the shipment. Including discharge socket and discharge cock as well as connection for link to grease separator.
Price group 095
Art. No. for NS DN Ø outside € / piece
48.01.00 1, 2, 4 100 110 u.r.48.01.50 7, 10 150 160 u.r.48.02.00 15, 20, 25 200 200 u.r.
Sampling pipe „K“ made of PE-HDfor separators installed in the ground. The sampling device consists of a PE-HD pipe with welded-in bottom and two inlet and discharge pipes offset in height by 100 mm. Easy to shorten to match frost-free depth. With cast iron top 330 x 330 mm including cast iron cover plate B 125.
Price group 095
Art. No. for NS DN Ø outside € / piece
48.21.01 1, 2, 4 100 110 u.r.48.21.51 7, 10 150 160 u.r.48.22.01 15, 20, 25 200 200 u.r.l frost-free 1200 mml for bulb-plate cover class D400 add „D“ in front of Art.No.
cast iron flap
Plastic pipeeasy to shorten
Filling unit made of PE-HDmade of polyethylene (flow rate) with free discharge for connecting 1“ fresh water line to free-standing grease separator systems, including trap DN 40.Inlet funnel 110 mm Ø screwed into bracket and 1“ pipe coupling, with anti-backflow spherical closure inside.
Price group 095
Art. No. Description € / piece
48.00.00 Filling unit incl. trap DN 40 u.r.
Muffe 1“
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOLIP stainless steel grease separatormobile
Type ECOLIP-E Chromtech Mobil 1with integrated sludge trap, discharge through service openings
Price group 095
Art. No. Description € / piece
89.00.20 ECOLIP-E Chromtech Mobil 1 u.r.l Special model or different NS‘s upon request
Flexible InletØ 40 mm
Discharge socketØ 40 mm
Drain cock 1 1/4“ atdischarge opening
Wheels lockable
Height of discharge socket (bottom)up to bottom edge of tank: 280 mm (plus wheels)
Type ECOLIP-E Chromtech Mobil 2with integrated sludge trap, discharge through service openings
Price group 095
Art. No. Description € / piece
89.00.10 ECOLIP-E Chromtech Mobil 2 u.r.l Special model or different NS‘s upon request
Flexible InletØ 40 mm
Discharge socketØ 40 mm
Drain cock 1 1/4“ atdischarge opening
Height of discharge socket (bottom)up to bottom edge of tank: 400 mm (plus wheels)
Räder feststellbar
Type ECOLIP-E Chromtech Mobil 3similar to DIN 4040/ÖNORM EN 1825, NS 1with integrated sludge trap, discharge through service openings
Price group 095
Art. No. Description € / piece
89.50.01 ECOLIP-E Chromtech Mobil 3 u.r.l Special model or different NS‘s upon request
Wheels lockable
outsi
de
outsi
de
Grea
se se
para
tors
�6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type ECOLIP-E Chromtech D eck conforms DIN 4040/ÖNORM EN 1825with separate sludge trap, discharge via direct discharge connection DN 100 PN 10
Price group 095
Type ECOLIP-E Chromtech G eck conforms DIN 4040/ÖNORM EN 1825with separate sludge trap, discharge through service openings
Price group 095
ECOLIP stainless steel grease separator NS 2 - NS 25Free-standing
Nominal Size Sludge trapArt. No.
Grease separatorArt. No. L A B C H Cap.
ST lCapGS l € / piece
NS 2 rightleft
80.02.5080.02.51
80.02.0080.02.01 1250 270 702 840 1460 200 l
85l515 l150 l u.r.
NS 4 rightleft
80.04.5080.04.51
80.04.0080.04.01 2110 490 770 1480 1590 400 l
115 l1065 l230 l u.r.
NS 7 rightleft
80.07.5080.07.51
80.07.0080.07.01 3450 860 770 2450 1590 700 l
150 l1750 l330 l u.r.
NS 10 rightleft
80.10.5080.10.51
80.10.0080.10.01 3740 950 1000 2650 1590 1000 l
190 l2480 l390 l u.r.
NS 15 rightleft
80.15.5080.15.51
80.15.0080.15.01 3760 950 1490 2670 1590 1500 l
245 l3780 l445 l u.r.
NS 20 rightleft
80.20.5080.20.51
80.20.0080.20.01 4110 980 1970 2990 1590 2000 l
305 l6000 l675 l u.r.
NS 25 rightleft
80.25.5080.25.51
80.25.0080.25.01 5100 1210 1995 3750 1590 2500 l
335 l7510 l790 l u.r.
Nominal Size Grease separatorArt. No. D e f B DN Total capacity
GS l € / piece
NS 2 rightleft
81.02.0081.02.01 1110 1396 1326 702 100 800 l
190 l u.r.
NS 4 rightleft
81.04.0081.04.01 1980 1396 1326 770 100 1700 l
300 l u.r.
NS 7 rightleft
81.07.0081.07.01 3310 1396 1326 770 150 2500 l
450 l u.r.
NS 10 rightleft
81.10.0081.10.01 3600 1396 1326 1000 150 3900 l
550 l u.r.
NS 15 rightleft
81.15.0081.15.01 3620 1396 1326 1490 200 5800 l
680 l u.r.
CoverNS 2/ 4 1 Piece A x B and C x B
NS 7 /10 / 15 1 Piece A x 600 mm and C x 600 mm
NS 20 / 25 1 Piece A x 600 mm and 2 Pieces 1310 x 600 mm
CoverNS 2/ 4 1 Cover and 1* Revision
NS 7 /10 / 15 2 Covers
flange for supply connection Ventilation Ø 110
NS 2 - NS 15
filling unit (optional)Ventilation Ø 110
l Special model or different NS‘s upon request
Lenght AWidht B
Lenght CWidht B
Lenght DWidht B
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type ECOLIP-E Chromtech VA oval similar to DIN 4040/ÖNORM EN 1825with integrated sludge trap, without partition wall, discharge via program-controlled discharge devicedischarge connection R 2 1/2“ outside thread PN 10
Price group 095
Type ECOLIP-E Chromtech A oval similar to DIN 4040/ÖNORM EN 1825with integrated sludge trap, without partition wall, discharge via manually controlled discharge device, homogenisation by mixer(s), discharge connection R 2 1/2“ outside thread PN 10
Price group 095
ECOLIP stainless steel grease separator NS 2 - NS 4Free-standing
Nominal size SemiautomaticArt. No. A B H a c DN Weight
kgGS
Capacity lSF
Capacity l € / piece
NS 2 rightleft
85.02.1085.02.11 1310 760 1590 1290 1220 100 270 730 200 u.r.
NS 4 rightleft
85.04.1085.04.11 1770 760 1590 1350 1280 100 300 960 400 u.r.
Inspection glassoptional Heater
Filling unit
Vent. connectionØ outside
Motor-driven mixer
Outlet
Inlet
l images show right flow
Nominal size Fully automaticArt. No. A B H a c DN Weight
kgGS
Capacity lSF
Capacity l € / piece
NS 2 rightleft
85.02.2085.02.21 1310 760 1590 1290 1220 100 270 730 200 u.r.
NS 4 rightleft
85.04.2085.04.21 1770 760 1590 1350 1280 100 300 960 400 u.r.
l images show right flow Inspection glassoptional Heater
Filling unit
Vent. connectionØ outside
Motor-driven mixer
Outlet
Inlet
l Special model or different NS‘s upon request
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type ECOLIP-E Chromtech A eck conforms DIN 4040/ÖNORM EN 1825with integrated sludge trap, without partition wall, discharge via manually controlled discharge device, homogenisation by mixer(s), discharge connection R 2 1/2“ outside thread PN 10
Price group 095
ECOLIP stainless steel grease separator NS 2 - NS 25Free-standing
Nominal sizeS1
G2Art. No. L A B C H DN Outside
Ø a b c STin l
GS.in l € / piece
NS 2S=200 lF=515 l
rightleft
86.02.1086.02.11 1440 450 700 840 1630 100 110 1315 350 1245 130 240 u.r.
NS 4S=400 lF=1065 l
rightleft
86.04.1086.04.11 2200 550 800 1500 1630 100 110 1315 400 1245 140 320 u.r.
NS 7S=700 lF=1750 l
rightleft
86.07.1086.07.11 3580 950 800 2480 1630 150 160 1335 400 1265 180 450 u.r.
NS 10S=1000 lF=2480 l
rightleft
86.10.1086.10.11 4050 1100 1000 2800 1630 150 160 1355 400 1285 215 530 u.r.
NS 15S=1500 lF=3780 l
rightleft
86.15.1086.15.11 4330 1200 1492 2980 1630 200 210 1305 400 1235 260 610 u.r.
NS 20S=2000 lF=6000 l
rightleft
86.20.1086.20.11 5440 1300 870 3990 1630 200 210 1305 400 1235 330 970 u.r.
NS 25S=2500 lF=7500 l
rightleft
86.25.1086.25.11 5440 1300 2330 3990 1630 200 210 1305 400 1235 390 1165 u.r.
1 Sludge trap capacity in liter (S)2 Grease separator capacity in liter (G)
CoverNS 2/ 4 1 Piece A x B and C x B
NS 7 /10 / 15 1 Piece A x 600 mm and C x 600 mm
NS 20 / 25 1 Piece A x 600 mm and 2 Pieces 1310 x 600 mm
l images show right flow
about 160 mm maximum grease layer to DIN
Ventilation
Filling unit Inspection glass
Control cabinet
Pump flange-mounted Motor-driven mixer
Semi-automated grease separator with motor-driven mixer(s) and separate sludge trap
l Special model or different NS‘s upon request
Lenght L21/2“ outside
Heigh
t H
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type ECOLIP-E Chromtech VA eck conforms DIN 4040/ÖNORM EN 1825with integrated sludge trap, without partition wall, discharge via program-controlled discharge devicedischarge connection R 2 1/2“ outside thread PN 10
Price group 095
ECOLIP stainless steel grease separator NS 2 - NS 25Free-standing
Nominal sizeS1
G2
Art. No.without heater
Art. No.with
heaterL A B C H
DNOutside
Øa b c
STGSin l
€ / piecewithout heater
€ / piecewith
heaterNS 2
S=200 lF=515 l
rightleft
86.02.5086.02.51
87.02.0087.02.01 1440 450 700 840 1630 100
110 1315 350 1245 130235 u.r. u.r.
NS 4S=400 lF=1065 l
rightleft
86.04.5086.04.51
87.04.0087.04.01 2200 550 800 1500 1630 100
110 1315 400 1245 140315 u.r. u.r.
NS 7S=700 lF=1750 l
rightleft
86.07.5086.07.51
87.07.0087.07.01 3580 950 800 2480 1630 150
160 1335 400 1265 180430 u.r. u.r.
NS 10S=1000 lF=2480 l
rightleft
86.10.5086.10.51
87.10.0087.10.01 4050 1100 1000 2800 1630 150
160 1355 400 1285 215510 u.r. u.r.
NS 15S=1500 lF=3780 l
rightleft
86.15.5086.15.51
87.15.0087.15.01 4330 1200 1492 2980 1630 200
210 1305 400 1235 260590 u.r. u.r.
NS 20S=2000 lF=6000 l
rightleft
86.20.5086.20.51
87.20.0087.20.01 5440 1300 1870 3990 1630 200
210 1305 400 1235 330940 u.r. u.r.
NS 25S=2500 lF=7500 l
rightleft
86.25.5086.25.51
87.25.0087.25.01 5440 1300 2330 3990 1630 200
210 1305 400 1235 3901080 u.r. u.r.
1 Sludge trap capacity in liter (S)2 Grease separator capacity in liter (G)
l Special model or different NS‘s upon request
CoverNS 2/ 4 1 Piece A x B and C x B
NS 7 /10 / 15 1 Piece A x 600 mm and C x 600 mm
NS 20 / 25 1 Piece A x 600 mm and 2 Pieces 1310 x 600 mm
l images show NS 10 right flow
about 160 mm maximum grease layer to DIN
Ventilation
Filling unit Inspection glass
Control cabinet
Pump flange-mounted
Motor-drivenmixer
Fully-automated grease separator with motor-driven mixer(s) and separate sludge trap
el. Heater
End switchLenght L
21/2“ outside
Heigh
t H
Grea
se se
para
tors
�0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Type ECOLIP-E Chromtech Praktikusfresh grease separator for separate, concentrated separation of sludge and grease into drums,manual or fully automated discharge
Price group 095
ECOLIP stainless steel grease separator NS 2 - NS 25Installation in the ground
l images show right flow
Ventilation
Discharge opening with sampling pointswivel-mounted. Inlet
Control cabinetWorm extruder withslotted hole screen forseparation of solids
Container for solids
swivel-mounted
swivel-mounted
Inspection glass
Grease container Heater
NS Art. No.Semiautomatic
Art. No.Fully automatic DN Outside
Ø C B L a c H kg € / pieceSemiautomatic
€ / pieceFully automatic
Unflanged worm extruder, discharge with removable ventilation, resulting in tank height 16652 88.00.02 88.10.02 100 110 1000 590 1480 1665 1300 1845 190 u.r. u.r.4 88.00.04 88.10.04 100 110 1230 590 1710 1665 1300 1845 210 u.r. u.r.7 88.00.07 88.10.07 150 160 2090 700 2570 1665 1300 1895 350 u.r. u.r.
Flanged as shown, largest part: C x B x 785 / NS 20 + 25: C x B x 86010 88.00.10 88.10.10 150 160 3110 1330 3590 1665 1300 1895 480 u.r. u.r.15 88.00.15 88.10.15 200 210 3110 1970 3590 1665 1300 1895 550 u.r. u.r.20 88.00.20 88.10.20 200 210 3590 2290 4070 1865 1500 2145 675 u.r. u.r.25 88.00.25 88.10.25 200 210 4120 2380 4600 1865 1500 2145 790 u.r. u.r.
l Special model or different NS‘s upon request
NSNSNS
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Nominal SizeS1
G2
Sludge trap + Grease separatormax. frost-free depth 1200 mm
Artikel-Nr.D Ø
Height of container
H mma c DN Outside
Ø kg € / piece
NS 1Cap. S = 100 l
G = 270 l84.01.12 800 1650 845 775 100 110 270 u.r.
NS 2Cap. S = 200 l
G = 550 l84.02.12 1160 1650 980 910 100 110 355 u.r.
NS 4Cap. S = 400 l
G = 1050 l84.04.12 1410 1650 1015 945 100 110 460 u.r.
NS 7Cap. S = 700 l
G = 1744 l84.07.12 1850 1650 995 925 150 160 670 u.r.
NS 10Cap. S = 1000 l
G = 2500 l84.10.12 SF 1160
GS 1850 1650 1020 950 150 160 790 u.r.
1 Sludge trap capacity in liter (S)2 Grease separator capacity in liter (G)l Total height ~ measure c + frost-free depth (800 - 1200 mm)
Type ECOLIP-E Chromtech E round conforms ÖNORM EN 1825with integrated Sludge trap, without partition wall, discharge through service openings
Price group 095
l Special model or different NS‘s upon request
ECOLIP stainless steel grease separator NS 1 - NS 10Installation in the ground
NS 1-7 with dome and 1 coverNS 10 - 15 with 2 tanks with 1 dome and cover each
subgrade of fine sand or fresh concrete
compacted sand layers
crushed stone base
5cm soft layer of mineral fibres supplied by owner
Surface
Concrete plate
Design counterac-ting groundwater pressure
Behä
lterh
öhe fro
stfre
ie Tie
fe
Reinforced concrete base plate, L x W or Ø, depending on load pressure, to be designed
by a structural engineer!
Grease separator with integrated sludge trap,cover concrete casting B 125 kN or D 400 kN
conta
iner h
eight fro
stfre
e dep
th
Grea
se se
para
tors
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
ECOLIP Stainless steel accessories
Sampling pipe made of stainless steel 1.4571made of sleeve-less Cr-Ni pipe, material No. 1.4571, for free-standing grease separator systems with closable access hole and cleaning brush to be supplied with the shipment. Including discharge socket and discharge cock as well as connection for link to grease separator.
Price group 095
Art. No. for NS DN Ø outside € / piece
98.00.70 1 70 75 u.r.98.01.00 2, 4 100 110 u.r.98.01.50 7, 10 150 160 u.r.98.02.00 15, 20, 25 200 200 u.r.
Filling unit made of stainless steel 1.4571Filling unit (4 ltr/s flow rate) with free discharge for connecting 1“ fresh water line to free-standing grease separator systems, including trap DN 40.Inlet funnel 110 mm Ø with bracket and 1“ threaded nipple.Made exclusively from Cr-Ni material No. 1.4571.Inlet funnel flange-mounted, with anti-backflow spherical closure inside.
Price group 095
Art. No. Description € / piece
98.00.00 Filling unit u.r.
1“ threaded nipple
Sampling pipe „K“ made of stainless steel 1.4571 made of Cr-Ni material no. 1.4571, for separators installed in the ground. CR-Ni flow pipe with stepped continuation, matching nominal size NS... and connection to SML pipe including CV connector. Plastic pipe easy to shorten for frost-free depth of 200 - 1300 mm.Cast iron top 340 mm Ø, class M 125.Additional extension per 400 mm unit - surcharge upon request
Price group 095
Art. No. for NS DN Ø outside € / piece
98.21.00 1, 2, 4 100 110 u.r.98.21.50 7, 10 150 160 u.r.98.22.00 15, 20, 25 200 200 u.r.l frost-free 1200 mm
Casting
Easy-to-trim plastic pipe
Conv
eyor
tech
niqu
e
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Used water pumps
CORONADA 200with stainless steel slide ring seal Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connec-
tion
Flowmax. (m³/h)
Pressure head
max. (m)€ / piece
Delivery connection(serial production)
CORONADA 200with 10 m cable 230 0,30 1,36 6,5
internal thread 1 1/4“
8,2 6 u.r.
CORONADA 200 KSwith ball float switch 230 0,30 1,36 6,5
internal thread 1 1/4“
8,2 6 u.r.
CORONADA 200SX/KSwith ball float switch, viton seal, special shaft
230 0,30 1,36 6,5internal thread 1 1/4“
8,2 6 u.r.
non-return flap
ROBUSTA 1, ROBUSTA 200 TS, ROBUSTA 300 TS with shaft sealing ring, pump housing PPRobusta 200TS / 300TS is suitable for use in narrow shafts due to TS control provided as a standard feature
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connec-
tion
Flowmax. (m³/h)
Pressure head
max. (m)€ / piece
Delivery connection(serial production)
ROBUSTA 1 äwith 10 m cable 230 0,28 1,3 3,0
internal thread 1 1/4“
6,0 6 u.r.
ROBUSTA 200 TSwith 10 m cable 230 0,48 2,1 3,3
internal thread 1 1/4“
10,8 6 u.r.
ROBUSTA 300 TSwith 10 m cable 230 0,50 2,2 3,8
internal thread 1 1/4“
13,8 8 u.r.
ä Robusta 1 without level control, flat-suction to 1 mm
Conv
eyor
tech
niqu
e
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
MF 054 bis MF 804with unchokable wheel, 20-60 mm completely free passage. Portable unit with 10 m cableand ball float switch
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connec-tion
Flowmax. (m³/h)
Pressure head
max. (m)
Grain size mm
€ / piecewithout KS
€ / piecewith KS
MF 054 W/KS 230 0,39 1,75 7,4 internal thread 1 1/4“ 7 7,5 20 u.r. u.r.MF 154 W/KS 230 0,66 2,95 9,0 internal thread 1 1/4“ 9,5 10 20 u.r. u.r.MF 254 W/KS 230 0,72 3,14 9,0 internal thread 1 1/4“ 18 8 30 u.r. u.r.MF 324 W/KS 230 0,83 3,61 9,0 internal thread 1 1/4“ 18 10 30 u.r. u.r.MF 354 W/KS 230 1,50 5,90 15,0 internal thread 2“ 31 10 40 u.r. u.r.MF 504 W/KS 230 2,00 8,06 17,0 internal thread 2“ 38 13 40 u.r. u.r.MF 334 D/KS 400 0,83 1,40 9,0 internal thread 1 1/4“ 18 10 30 u.r. u.r.MF 404 D/KS 400 1,50 2,08 15,0 internal thread 2“ 31 10 40 u.r. u.r.MF 804 D/KS 400 2,60 4,10 20,0 internal thread 2“ 43 15 40 u.r. u.r.MF 565 W/KS 230 2,40 10,80 20,0 DN 65 57 8 60 u.r. u.r.MF 665 D/KS 400 2,20 4,10 20,0 DN 65 57 8 60 u.r. u.r.
Used water pumps
Immersion construction pump JumboPlug-in construction pump with power cable 10 m Anschlusskabel, 6 mm completely free passage Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Motor rating P2 (kW)
Weight (kg)
Delivery connec-
tion
Flowmax. (m³/h)
Pressure head
max. (m)€ / piece
JUMBO 5 230 0,59 0,48 9,5 2“ 14 11 u.r.l further immersion construction pumps „JUMBO“ upon request
Conv
eyor
tech
niqu
e
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PIRANHA, 09 S12 - S26with cutting device, cable 10 m
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg) Delivery connection Flow
max. (m³/h)Pressure head
max. (m)€ / piece
without KS€ / piece äwith KS
PIRANHA 09-D/KS 400 2,6 4,6 23 internal thread 1 1/4“ 13 20 u.r. u.r.PIRANHA 12-2D/KS 400 1,7 3,3 32 internal thread 1 1/4“ 8 23 u.r. u.r.PIRANHA 17-2D/KS 400 2,3 4,0 32 internal thread 1 1/4“ 9 30 u.r. u.r.PIRANHA 21-2D/KS 400 2,8 4,8 37 internal thread 1 1/4“ 13 33 u.r. u.r.PIRANHA 26-2D/KS 400 3,4 5,6 40 internal thread 1 1/4“ 16 37 u.r. u.r.ä KS model incl. control unit, CEE plug and level control, without Klixon and DI
Waste water immersion motor pumps
A B CPIR S12-S17 305 402 130PIR S21-S26 305 415 130
AS 0530-0840Immersion motor pumps with CB system CONTRA-BLOC® or with unchokable wheel, cable 10m
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connec-tionDN
Flowmax. (m³/h)
Pressure headmax. (m)
€ / piecewithout KS
€ / piece äwith KS
AS 0530 S12-2D/KS 400 1,7 3,2 34 50 32 13 u.r. u.r.AS 0630 S13-4D/KS 400 1,9 3,6 37 65 38 10 u.r. u.r.AS 0830 S13-4D/KS 400 1,9 3,6 40 80 38 10 u.r. u.r.AS 0840 S17-2D/KS 400 2,3 4,0 35 80 58 17 u.r. u.r.ä KS model incl. control unit, CEE plug and level control, without Klixon and DI
A B C D F GAS 0530 S12-2 435 290 183 160 125 175AS 0630 S13-4 448 307 290 160 140 247AS 0830 S13-4 448 307 290 160 200 342AS 0840 S17-2 418 250 262 130 200 342
Conv
eyor
tech
niqu
e
�6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
SANIMAX-S und SANIMAX-MFUsed water lifting systems with Pump, overground; tank capacity = 25 l with integrated trap (activated carbon)
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connection
DN
Flowmax. (m³/h)
Pressure head
max. (m)€ / piece
SANIMAX-S Robusta 202 TS 230 0,48 2,1 9 40 8 6 u.r.
SANIMAX-MF 054W 230 0,39 1,75 9 40 7,5 7,5 u.r.SANIMAX-MF 154W 230 0,66 2,95 9 40 11 10,5 u.r.SANIMAX-MF 324W 230 0,78 3,61 9 40 22 10 u.r.
Used water lifting systems
NIROLIFTFloor outlet with used water pump incl. float control, underground; tank capacity = 100 l Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connection
DN
Flowmax. (m³/h)
Pressure head
max. (m)€ / piece
NIROLIFTwithout top piece 230 0,48 2,1 8,9 50 8 6 u.r.
1) Connection for SML pipe DIN 19522 or KG pipe DIN 19531
2) Connection for KG pipe DIN 195313) for steel pressure line: Outer Ø: 60,3 mm
Plastic: Outer Ø: 63,0 mm4) 30 - 133 mm depending on top piece
Accessory products Price group 000
Art. No. Description € / piece
42480013 Cast iron top and grid, asphalt-paved u.r.61090016 Trap for 42480013 u.r.42480016 Top PP, Cr-Ni grating u.r.
Conv
eyor
tech
niqu
e
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Used water lifting systems
SANISETT 1 + SANISETT 2Prefabricated used water gully, bottom outlet incl. control unit, underground Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input
l nom (A)
Weight (kg)
Delivery connection
DN
Flow max. (m³/h)
Pressure head
max. (m)
€ / piecewithout KS
SANISETT 1Complete system with pump ROBUSTA 200 TS, control unit, cover plate and trap
230 0,48 2,1 21,3 50 8 6 u.r.
SANISETT 2Complete system with pumps ROBUSTA 200 TS, control unit, cover plate and trap
230 2 x 0,48 2 x 2,1 25,6 50 8 6 u.r.
l different pump types upon request
Accessory products for SANISETT 1 und 2 Price group 000
Art. No. Description € / piece
6 190 0019 Shaft extension max. 180 mm, with vent and carbon filterDIN 19541, to replace top 4 248 0013 and 4 248 0014 u.r.
6 190 5104 Cap, required only if SANISETT2 is used as stand-alone unit u.r.
Conv
eyor
tech
niqu
e
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Used water lifting systems
PIRANHAMAT 100/120 Small used water lifting system for domestic effluents with shredder, cable 2 m; tank capacity = 12 l, housing vent with activated carbon filter, incl. non-return flap, to be placed direct behind toilet
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connection
DN
Flow max. (m³/h)
Pressure head max. (m)
tank capacity
l
€ / piecewithout KS
PIRANHAMAT 100 230 1,10 4,7 9,0 25/32 7 7 12 u.r.PIRANHAMAT 120 with alert 230 1,10 4,7 9,0 23/32 7 7 12 u.r.
PIRANHAMAT 1002 used water lifting system for domestic effluents Solids handling sewage lift system incl. control unit and non-return flap, tank capacity = 100 l
Price group 096
Under EN 12056-4, rooms housing used water lifting systems must be large enough to provide working space of a minimum width of 60 cm beside and above all parts requiring service and maintenance. Provide a pump sump for room drainage.
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery con-nection
DN
Flow max. (m³/h)
Pressure head max. (m) € / piece
PIRANHAMAT 1002 D 400 2 x 230 2 x 4,0 98 2 x 32 9,5 25 u.r.
Vent
Manual control
Level control
Pump position in case of single unit
Inspection openings
Pressure line
Connections
Inlet horizontal (1) DN 100 (2) DN 100 (3) DN 100 (4) DN 100 (5) DN 150Inlet vertical (6)1) DN 100 (7) 1) DN 100 (8) DN 50 (9) DN 100 (10) 2) DN 100Pressure line () DN 100Vent (V) DN 100
1) can also be used as roof vent2) can be used as connection for manually operatred membrane pump
Conv
eyor
tech
niqu
e
��
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Used water lifting systems
PIRANHAMAT 701 used water lifting system for domestic effluentsSolids handling sewage lift system incl. control unit and non-return flap, tank capacity = 70 l
Price group 096
Under EN 12056-4, rooms housing used water lifting systems must be large enough to provide working space of a minimum width of 60 cm beside and above all parts requiring service and maintenance. Provide a pump sump for room drainage.
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery con-nection
DN
Flow max. (m³/h)
Pressure head max. (m) € / piece
PIRANHAMAT 701 D 400 2,30 4,0 58 32 9 30 u.r.
SANIMAT 1000 S-1Solids handling sewage lift system incl. control unit and non-return flap, cable 4 m; tank capacity = 68 l
Price group 096
Under EN 12056-4, rooms housing used water lifting systems must be large enough to provide working space of a minimum width of 60 cm beside and above all parts requiring service and maintenance. Provide a pump sump for room drainage.
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connection
DN
Flow max. (m³/h)
Pressure head max. (m) € / piece
SANIMAT 1000 S-1/ D 400 1,70 3,3 50 80 36,0 9 u.r.
Inlet with pipe adapter (1) DN 100Inlet with temporary cover (2) DN 100Inlet (3) DN 100Inlet (4) DN 70
Inlet (5) DN 70Inlet/Vent (6) DN 70Inlet/Vent (7) DN 70Inlet/man. operated membrane pump (8) DN 40
Level control (9) DN 40Pressure line (10) conn. socket 4“ 1)
Gate valve DN 80 - not included in scope of delivery
1) or for pipe DN 100
Conv
eyor
tech
niqu
e
�00
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
SANIMAT 1702Solids handling sewage lift system incl. control unit and non-return flap, tank capacity = 170 l
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery connection
DN
Flow max. (m³/h)
Pressure head max. (m) € / piece
SANIMAT 1702 AS 12D 400 2 x 1,70 2 x 3,2 130 80 50 12,5 u.r.SANIMAT 1702 AS 17D 400 2 x 2,30 2 x 4,0 130 80 58 17 u.r.SANIMAT 1702 AS 26D 400 2 x 3,40 2 x 5,6 140 80 67 21 u.r.
Connection
(1) DN 100 Inlet(2) DN 100 Inlet(3) DN 100 Inlet(4) DN 100 Inlet(5) DN 150 Inlet(6)1) DN 100 Inlet/Vent(7) DN 70 Inlet/Vent(8) 2) DN 40 Inlet/man. operated membran pump(9) DN 40 level control(10) 2) DN 150 Inlet(11) Elast. conn. 4“ pressure line
1) optional use as vent over roof2) can be used as man. operated membran pump
Used water lifting systems
SANIMAT 1001 and 1002Solids handling sewage lift system incl. control unit and non-return flap, cable 4 m; tank capacity = 100 l
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery con-nection
DN
Flow max. (m³/h)
Pressure head max. (m) € / piece
SANIMAT 1001 D 400 1,70 3,2 62 80 32,2 9 u.r.SANIMAT 1001 D/HD 400 2,30 4,0 62 80 40,3 11 u.r.SANIMAT 1002 D 400 2 x 1,70 2 x 3,2 88 80 32,2 9 u.r.SANIMAT 1002 D/HD 400 2 x 2,30 2 x 4,0 88 80 40,3 11 u.r.
Connection
Inlet horizontal (1) DN 100 (2) DN 100 (3) DN 100 (4) DN 100 (5) DN 150Inlet vertical (6)1) DN 100 (7) 1) DN 100 (8) DN 50 (9) DN 150 (10) 2) DN 40Pressure line (1) conn. socket 4“ *)
Vent (2) DN 70
1) optional use as vent over roof2) can be used as man. operated membran pump*) or for pipe DN 100
Gate valve DN 80 - not included in scope of delivery
Conv
eyor
tech
niqu
e
�0�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Accessory ProductsMechanical accessories, fittings
Price group 000
Art. No. Description Size € / piece
62325012Pump foot complete
with bracket and pipe clamper
1 1/4“ u.r.62320560 2“ u.r.62320673 DN 65 u.r.62320649 DN 80 u.r.
SCHIEBER-MS-5/4Gate valve (Ms) PN 16
with socket
internal thread 1 1/4“ u.r.SCHIEBER-MS-2 internal thread 2“ u.r.SCHIEBER-MS-5/2 internal thread 2 1/2“ u.r.
SCHIEB65AVK 0630 Gate valve (SGCI-50),
epoxy-coated, soft-sealing
DN 65 u.r.
61420500 DN 80 u.r.61420501 DN 100 u.r.61420503 DN 150 u.r.
61400511 Non-return flap (Synthetic),with socket
internal thread 1 1/4“ u.r.61400513 internal thread 2“ u.r.
RKL-MS-5/4Non-return flap (Ms),
with socket
internal thread 1 1/4“ u.r.RKL-MS-2 internal thread 2“ u.r.RKL-MS-5/2 internal thread 2 1/2“ u.r.
61400525 Ball check valve (GG-20),with socket
internal thread 1 1/4“ u.r.61400527 internal thread 2“ u.r.
61400543 Ball check valve (SGCI-40), with socket internal thread 2 1/2“ u.r.HDL65-5087EPOX Ball check valve (SGCI-40),
with flangeDN 65 u.r.
61400523 DN 80 u.r.
14990028 Manually operated membrane pump with integrated check valve with wall bracket internal thread 1 1/2“ u.r.
Used water and waste water system accessories
Conv
eyor
tech
niqu
e
�0�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Used water and waste water system accessories
Accessory productsElectrical accessories
Price group 000
Art. No. Description € / piece
KS-level switch (for ISO, ISO-HL, LSC and P control). Individual KS float switches also for retrofitting, with 1 KS switch for each pump and alarm unit1 280 0021 KS 3 = 3 m Cable u.r.1 280 0022 KS 5 = 5 m Cable u.r.1 280 0023 KS 10 = 10 m Cable u.r.1 280 0025 KS 20 = 20 m Cable u.r.
AQUALEVEL KS level switch with 10 m cable, wall bracket and poise weight6 245 0052 KS 2 Switch u.r.6 245 0058 KS 3 Switch u.r.
KS 5 Switch ( 6 245 0052 + 6 245 0058) u.r.
Plug-in alarm
1 602 0201For 230 V shock-proof plug with buzzer, alarm diode and acknow-ledgement button, potential-free fault alarm output, mains-opera-
ted but fitted with loading device for mains-independent operationu.r.
624 50 039 Washing machine shutoff incl. NSM05 alarm device u.r.
Fertigpumpstation - Kunststoff
SYNCONTA 801-PIR S12 to 801-PIR S26 Synthetic complete manholes with pump and control cabinet with Pneumostatand, manhole top
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Delivery con-nection
DN
Flow max. (m³/h)
Pressure head max. (m) € / piece
Single-pump units, stainless steel piping (material no. 1.4301)SYNCONTA 801-PIR S12-D 400 1,7 3,3 50 8,0 23 u.r.SYNCONTA 801-PIR S17-D 400 2,3 4,0 50 9,4 30 u.r.SYNCONTA 801-PIR S21-D 400 2,8 4,8 50 14,0 34 u.r.SYNCONTA 801-PIR S26-D 400 3,4 5,6 50 16,0 37 u.r.l also available with pump AS0530 or MF 354-804shaft extension u.r.
Pressure line connection with outside thread G 2“
connection pipe for ventilation/cable duct, connection with DIN plug coupling
inlet pipe DN 150, connection with DIN plug coupling
ABS coupling above water level complete with bracket
NEW!
Conv
eyor
tech
niqu
e
�0�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Prefabricated pumping unit - plastic
SYNCONTA 901-PIR S12 up to 902-PIR S26Synthetic prefabricated shafts complete with pump(s) and control cabinet with Pneumostat and shaft top - accessible
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Weight (kg)
Delivery con-nection
DN
Flow max. (m³/h)
Pressure head max. (m) € / piece
Single-pump units, stainless steel piping (material no. 1.4301)SYNCONTA 901-PIR S12-D 400 1,7 3,3 172 50 8,0 23 u.r.SYNCONTA 901-PIR S17-D 400 2,3 4,0 172 50 9,4 30 u.r.SYNCONTA 901-PIR S21-D 400 2,8 4,8 177 50 14,0 34 u.r.SYNCONTA 901-PIR S26-D 400 3,4 5,6 180 50 16,0 37 u.r.Twin-pump units, stainless steel piping (material no. 1.4301)SYNCONTA 902-PIR S12-D 400 2 x 1,7 2 x 3,3 204 50 8,0 23 u.r.SYNCONTA 902-PIR S17-D 400 2 x 2,3 2 x 4,0 204 50 9,4 30 u.r.SYNCONTA 902-PIR S21-D 400 2 x 2,8 2 x 4,8 214 50 14,0 34 u.r.SYNCONTA 902-PIR S26-D 400 2 x 3,4 2 x 5,6 220 50 16,0 37 u.r.
flushing water supply for SYNCONTA 2“ Storz u.r.
shaft extension to total height 2.190 mm / 901L / 902L u.r.
Synconta 901/902 Synconta 901L/902L
8) Pressure line connection with outside thread G 2“
9) connection pipe for ventilation/cable duct, connection with DIN plug coupling
10) inlet pipe DN 150, connection with DIN plug coupling
5) ABS coupling above water level complete with bracket
Conv
eyor
tech
niqu
e
�0�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURACONTA Prefabricated pumping unit - concrete
PURACONTA 1-PIR S12 bis 2-PIR S26Prefabricated pumping unit, made of condrete, complete system with pump(s), control cabinet with Pneumostat and shaft top - trafficable
Price group 096
Type Voltage(V)
Motor rating P1 (kW)
Power input l nom (A)
Delivery con-nection
DN
Flow max. (m³/h)
Pressure head max. (m) € / piece
Single-pump units, stainless steel piping (material no. 1.4301)PURACONTA 1-PIR S12-D 400 1,7 3,3 50 8,0 23 u.r.PURACONTA 1-PIR S17-D 400 2,3 4,0 50 9,4 30 u.r.PURACONTA 1-PIR S21-D 400 2,8 4,8 50 14,0 34 u.r.PURACONTA 1-PIR S26-D 400 3,4 5,6 50 16,0 37 u.r.Twin-pump units, stainless steel piping (material no. 1.4301)PURACONTA 2-PIR S12-D 400 2 x 1,7 2 x 3,3 50 8,0 23 u.r.PURACONTA 2-PIR S17-D 400 2 x 2,3 2 x 4,0 50 9,4 30 u.r.PURACONTA 2-PIR S21-D 400 2 x 2,8 2 x 4,8 50 14,0 34 u.r.PURACONTA 2-PIR S26-D 400 2 x 3,4 2 x 5,6 50 16,0 37 u.r.
flushing water supply for PURACONTA 2“ Storz u.r.
l different system combinations (shaft depth, pumps) upon request
400 kN
trafficable
Inlet
Instal
lation
depth
Conv
eyor
tech
niqu
e
�0�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Prefabricated pumping unit - concrete
Prefabricated pumping unitfor trafficable areas
Standard Typen Shaft Ø m
Min. Inst.depth
m
Inlet depthm € / piece
FP100/ 1,00 2,00 0,80 u.r.FP150/ 1,50 2,28 0,88 u.r.FP200/ 2,00 2,28 0,88 u.r.FP250/ 2,50 2,28 0,88 u.r.
ADVANTAGES• brief construction time• no need for formwork• can be adapted to local conditions• monolithic, leak-proof
required BASIC INFORMATION• Type of pump• Control cabinet (inside/outside)• Loading class of top• Control system• Medium to be pumped• Flow and height• Special requirements
Prefabricated pumping unit FP 100/1/ Prefabricated pumping unit FP 200/2/
Customised solutions regarding inlet/insertion depth, anti-buoyancy protection, loading class, control etc.
Cover
pressure pipe
Inlet
mounting manhole
cable protection pipe DN100leading to control cabinet
Cover Cover
pressure pipe
Inlet
mounting manhole
cable protection pipe DN100leading to control cabinet
manhole Ø 60
mounting manhole
Conc
rete
par
ts
�06
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PREFABRICATED CONCRETE PARTS
PREFABRICATED CONCRETE PARTS – SINGLE UNITSConcrete well rings, cones Price group 091
Art. No. Inner Ø Dm
Wall thickness scm
Height hcm Weight (kg) € / piece
without step€ / piecewith step
Well Rings 82a 0,80 7 50 235 u.r. -102a 1,00 7 50 300 u.r. -
H102a 1,00 7 25 150 u.r. -122a(st) 1,20 7 50 350 u.r. u.r.152a(st) 1,50 8 50 500 u.r. u.r.
H152a(st) 1,50 8 25 250 u.r. u.r.152a-100 1,50 8 100 1000 u.r. -
202a-100(st) 2,00 9 100 1470 u.r. u.r.202a-75(st) 2,00 9 75 1110 u.r. u.r.
202a(st) 2,00 9 50 740 u.r. u.r.H202a(st) 2,00 9 25 365 u.r. u.r.
252a-100(st) 2,50 9 100 1850 u.r. u.r.252a-75(st) 2,50 9 75 1360 u.r. u.r.
252a(st) 2,50 9 50 920 u.r. u.r.H252a(st) 2,50 9 25 460 u.r. u.r.
Concrete well rings with inlet opening up to NW 250 mm
82aEA 0,80 7 50 235 u.r. -102aE 1,00 7 50 300 u.r. -
152aE(st) 1,50 8 50 490 u.r. u.r.202aE(st) 2,00 9 50 735 u.r. u.r.252aE(st) 2,50 9 50 920 u.r. u.r.
Concrete well rings with drainage openings 82s 0,80 7 50 230 u.r. -102s 1,00 7 50 340 u.r. -152s 1,50 8 50 495 u.r. -202s 2,00 9 50 740 u.r. -252s 2,50 9 50 910 u.r. -
Rings with bottom (bottom rings) 83 0,80 7 53 360 u.r. -103 1,00 7 60 525 u.r. -153 1,50 8 60 1200 u.r. -203 2,00 9 60 1850 u.r. -253 2,50 9 60 2650 u.r. -
A = Phase-out modell (st) = with step irons
Art. No. Inner Ø Dm
Wall thickness scm
Height hcm
Test loadkN
Weight (kg) € / piece
Cones 151 0,60/1,50 8 55 50-400 575 u.r.151AZ 0,60/1,50 8 60 50-400 630 u.r.201-60 0,60/2,00 9 62 50-400 1020 u.r.251-60 0,60/2,50 9 86 50-400 1600 u.r.
l AZ = out-of-centre manhole
Conc
rete
par
ts
�0�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PREFABRICATED CONCRETE PARTS
PREFABRICATED CONCRETE PARTS – SINGLE UNITSCover plates, well ring covers Price group 091
Art. No. outside Ø Dm
Height hcm
Test loadkN
Weight (kg) € / piece
Well ring cover, 2 parts
BR.DE80GET 1,06 7 accessible 104 u.r.BR.DE100GET 1,26 7 accessible 155 u.r.
Cover plates with central/lateral openingØ 60 cm
85Ba1, A 1,00 12 50 150 u.r.85Bc 1,00 12 125 150 u.r.85Be 1,00 12 400 150 u.r.
105a1 1,20 12 50 255 u.r.105c 1,20 12 125 270 u.r.105e 1,20 15 400 330 u.r.
Cover plates with lateral openingØ 60 cm
125a-11 1,40 14 accessible 470 u.r.125c-1 1,40 14 BK II 473 u.r.125e-1 1,40 14 BK I 473 u.r.
155a-11 1,70 15 accessible 750 u.r.155c-1 1,70 15 BK II 750 u.r.155e-1 1,70 20 BK I 1000 u.r.
205a-12 2,20 15 accessible 750 u.r.205c-13 2,20 20 BK II 1760 u.r.205e-13 2,20 20 BK I 1760 u.r.
255a-12 2,74 25 accessible 2040 u.r.255c-13 2,74 20 BK II 2810 u.r.255e-13 2,74 20 BK I 2810 u.r.
Cover plates with lateral openingØ 80 cm
125BaA 1,40 14 accessible 390 u.r.125Bc 1,40 14 BK II 390 u.r.125Be 1,40 14 BK I 390 u.r.
155BaA 1,70 15 accessible 630 u.r.155Bc 1,70 15 BK II 683 u.r.155Be 1,70 20 BK I 900 u.r.
205Ba 2,20 20 accessible 1415 u.r.205Bc 2,20 20 BK II 1650 u.r.205Be 2,20 20 BK I 1650 u.r.
255Ba 2,74 20 accessible 2600 u.r.255Bc 2,74 20 BK II 2750 u.r.255Be 2,74 20 BK I 2750 u.r.
1 = with spigot for concrete cover 1b or 1c2 = also available with 2, 3 or 4 openings D = 60 cm upon request3 = also available with 2 or 3 openings D = 60 cm upon requestA = phase-out model
Conc
rete
par
ts
�0�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PREFABRICATED CONCRETE PARTSmiscellaneous
Well sealing foam Price group 000Art. No. Description € / piece
BrunnenschaumSingle-component polyurethane foam
for sealing shaft rings(not suitable for cesspools!)
u.r.
Step irons, stirrups Price group 150
Art. No. # Description € / piece
1066-6 uGrey cast iron step irons for place-
ment in fresh concrete u.r.
17063ä - Kanalith cast iron steps irons u.r.
21B618 vPoly-Norm stirrups, cranked, with
insulating wall-plugs for straight walls u.r.ä without image
u v
Cementing prefabricated concrete partswith 2-component adhesive Price group 000
Art. No. Description Ø m € / piece
Kleben-80 Prefabricated parts cemented at the plant 0,80 u.r.Kleben-100 Prefabricated parts cemented at the plant 1,00 u.r.Kleben-150 Prefabricated parts cemented at the plant 1,50 u.r.Kleben-200 Prefabricated parts cemented at the plant 2,00 u.r.Kleben-250 Prefabricated parts cemented at the plant 2,50 u.r.
Installation of sockets in prefabricated concrete parts Price group 000
Art. No. Description Ø m € / piece
Muffeneinbau-100 Installation of sockets, at the plant 100 u.r.Muffeneinbau-150 Installation of sockets, at the plant 150 u.r.Muffeneinbau-200 Installation of sockets, at the plant 200 u.r.Muffeneinbau-250 Installation of sockets, at the plant 250 u.r.Muffeneinbau-300 Installation of sockets, at the plant 300 u.r.
Protective coating - internal coating Price group 000Art. No. Description € / piece
Schutzanstr - 25 kg Bituminous coating 25 kg can u.r.INL PEHD PE-HD Inliner lining u.r.
Anti-buoyancy protectionfor compact concrete tanks Price group 000
Art. No. Description € / piece
ATRS-150 for concrete tanks with Inner Ø = 1,5 m u.r.ATRS-200 for concrete tanks with Inner Ø = 1,5 m u.r.ATRS-250 for concrete tanks with Inner Ø = 1,5 m u.r.
Ladders made of aluminium, poly-steel, stainless steel
Conc
rete
par
ts
�0�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURATOR valve shaft, complete solutionConcrete shaft with valve, flaps or outflow limiter
Advantages
n Complete solution
n little assembly effort required
n many options for variations
n top-quality materials
gate valve
outlet
intlet
cover surface boxes
Ø D btw. LxW
��0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Sewa
ge tr
eatm
ent
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.
Table of contentsSewage treatment
Kanalith - concrete shaft system 112
Puraplast PE manhole 114
Boxless sliding gates 119
Back-water gates and antiflooding valves 122
Pipe ducts 129
Kana
lith
conc
rete
shaf
t sys
tem
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
KANALITH shafts - single units
Price group 091
Art. No. Inner Ø Dm
wall thick-ness s cm
height hcm
Test loadkN
Weight (kg) € / piece
Entry cover 1b 0,66 - - 30 50 u.r.1c 0,66 - - 50 62 u.r.
Compensating frame
60f 0,60 9 10 - 42 u.r.60g 0,60 8 15 - 53 u.r.
Compensating ring (without rebate) 59 0,60 9 5 - 25 u.r.60 0,60 9 10 - 49 u.r.61 0,60 9 20 - 100 u.r.62 0,60 9 15 - 75 u.r.80 0,80 9 8 - 57 u.r.
Cone with steps 81c 0,60/0,80 7 30 - 160 u.r.101c 0,80/1,00 7 30 - 190 u.r.181c 0,60/1,00 7 60 - 350 u.r.
Rings without steps 6a 0,60 8 25 - 106 u.r.6b 0,60 8 13 - 50 u.r.6d 0,60 8 20 - 86 u.r.62a 0,60 8 50 - 207 u.r.62f 0,60 8 60 - 250 u.r.80f 0,80 8 8 - 60 u.r.9 1,00 7 12 - 95 u.r.
Rings with steps 82d 0,80 7 30 - 140 u.r.82f 0,80 7 60 - 277 u.r.
102d 1,00 7 30 - 180 u.r.102f 1,00 7 60 - 360 u.r.
Rings without steps, with inlet/outlet
102fEE 1,00 7 60 - 340 u.r.
Cover plates with round opening Ø 60 cm 105as 1,20 2 - 12 50 255 u.r.105cs 1,20 2 - 12 125 270 u.r.105es 1,20 2 - 15 400 330 u.r.
Cover plates with rectangular opening60 x 100 cm
105agw 1,20 2 - 12 50 170 u.r.105egw 1,20 2 - 15 400 215 u.r.
Cover plates with square opening60 x 60 cm incl. steel checker plate or galvanised cover
105as17136 1 1,20 2 - 12 50 238 u.r.105as17166.00 1 1,20 2 - 12 50 238 u.r.105as17166.10 1 1,20 2 - 12 50 238 u.r.1 for detailed description of covers see image folder, 2 outside Ø m
Kana
lith
conc
rete
shaf
t sys
tem
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Flushing gully
The problemUsed water and mixed water sewers are used to carrywaste water to the treatment plant. For a variety of reasons,material is deposited in the sewers.
The consequences are:• Odour nuisance• Danger of corrosion due to the formation of biogenic sul-
phuric acid• Reduced hydraulic action • High cleaning costs• Higher administrative and organisational costs due, for
example, to additional effort required
The solution• Automatic flushing without any need for energy input• Can be mounted on any DN 1000 gully bottom and is
installed like a common sewer inspection manhole• Attains powerful flushing effect due to strong gush of water• Initiates flushing automatically once the storage unit is full.
Even small amounts of precipitation are collected and used for flushing.
• Reduces excess deposits and high sewer cleaning costs and the associated effort
Flushing gully Price group 000Art. No. Inner Ø m Height m Weight € / piece
Spülschacht Typ U 1,00 / 1,20 1,05 depending on model u.r.Spülschacht Typ A 1,00 / 1,20 1,05 depending on model u.r.
Type U
Flushing volume:about 500 l
Typ A
Flushing volume:about 500 l
Examples of use
Flushing gully Typ UAs first gully in connection to mains, requiredsewer depth ≥ 1.50 m (flushing water inlet)
Flushing gully Typ AAs intermediate gully in connection to mains, requiredsewer depth = 2.00 m (flushing water e.g. from estate drai-nage such as yard drainage, gutter, etc.)
Pura
plas
tPE
man
hole
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PE manhole DN 425 Price group 099
Art. No. # Description Number of inlets
Inlet DN mm
OutletDN mm
Height1
min/maxcm
€ / piece
E42/20 v Elevation - - - 20 u.r.5B42/50 u Base 5 100-150 100-150 37/50 u.r.5B42/70 u Base 5 100-150 100-150 35/70 u.r.
PE manhole DN 600 Price group 099
Art. No. # Description Number of inlets
Inlet DN mm
OutletDN mm
Height1
min/maxcm
€ / piece
E60/20 v Elevation - - - 10/20 u.r.E60/40ä - Elevation - - - 20/40 u.r.3B60/100ä - Base 3 100-300 200-300 60/100 u.r.5B60/60 u Base 5 100-150 100-150 35/60 u.r.5B60/80 u Base 5 100-150 100-150 ../80 u.r.RB60/100ä - Base round bottom - - - 60/100 u.r.ä without image
PURAPLAST PE manhole
AccessoryArt. No. Description € / pieceES 600 Ring seal Ø 600 mm u.r.
1 Height = from channel bottom to upper edge - (without cover)
u
u
v
AccessoryArt. No. Description € / pieceES 425 Ring seal Ø 425 mm u.r.
u
v
u
NEW!
NEW!
Pura
plas
tPE
man
hole
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PE manhole DN 800 Price group 099
Art. No. # Description Number of inlets
Inlet DN mm
OutletDN mm
Height1
min/maxcm
€ / piece
U80/40 w Cone - - - 20/40 u.r.U80/55 w Cone - - - 20/55 u.r.E80/40 v Elevation - - - 20/40 u.r.E80/100 v Elevation - - - 60/100 u.r.3B80/100ä - Base 3 100-300 200-300 70/100 u.r.5B80/50 u Base 5 100-150 100-150 40/50 u.r.RB80/80ä - Base round bottom - - - 50/80 u.r.ä no image
w
1 Height = from channel bottom to upper edge - (without cover)
PURAPLAST PE manhole
AccessoriesArt. No. Description € / pieceES 800 Ring seal Ø 800 mm u.r.
Setconsisting of manhole + sing seals
Art. No. Description Number of inlets
Inlet DN mm
OutletDN mm
Height1
min/maxcm
€ / piece
SET-3B/80-140 complete set 3 100-300 200-300 90/140 u.r.SET-5B/80-90 complete set 5 100-150 100-150 60/90 u.r.special solution: single-part manholeSET-5C/80-120 single-part manhole 5 100-150 100-150 90/120 u.r.
Image shows complete manhole SET-5C/80-120ä
v
u
NEW!
Pura
plas
tPE
man
hole
��6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PE manhole DN 1000 Price group 099
Art. No. # Description Number of inlets
Inlet DN mm
OutletDN mm
Height1
min/maxcm
€ / piece
U100/75 w Cone - - - 63/75 u.r.U100/100 w Cone - - - 70/100 u.r.E100/50 v Elevation - - - 40/50 u.r.E100/100 v Elevation - - - 90/100 u.r.1B100/60ä - Base 1 100-250 150-250 47/60 u.r.3B100/70ä - Base 3 100-400 300-400 55/70 u.r.5B100/60 u Base 5 100-250 150-250 47/60 u.r.ä no image
v
w
u
PURAPLAST PE manhole
AccessoriesArt. No. Description € / pieceES 1000 Ring seal Ø 1000 mm u.r.
1 Height = from channel bottom to upper edge - (without cover)
NEW!
Pura
plas
tPE
man
hole
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURAPLAST PE manhole
PE manhole DN 1000Complete manhole system with 5 inlets DN 100-250 and 1 outlet DN 200-250
Price group 099
Art. No. max. Heightcm
Base5B100-60
ElevationE100-50
Elevation E100-100
ConeU100-75
ConeU100-100
SealES 100 € / piece
SET-5B-100-135 135 1 - - 1 - 1 u.r.SET-5B-100-160 160 1 - - - 1 1 u.r.SET-5B-100-185 185 1 1 - 1 - 2 u.r.SET-5B-100-210 210 1 1 - - 1 2 u.r.SET-5B-100-235 235 1 - 1 1 - 2 u.r.SET-5B-100-260 260 1 - 1 - 1 2 u.r.SET-5B-100-285 285 1 1 1 1 - 3 u.r.SET-5B-100-310 310 1 1 1 - 1 3 u.r.
PE manhole DN 1000Complete manhole system with 3 inlets DN 100-400 and 1 outlet DN 300-400
Price group 099
Art. No. max. Heightcm
Base3B100-70
ElevationE100-50
Elevation E100-100
ConeU100-75
ConeU100-100
SealES 100 € / piece
SET-3B-100-145 145 1 - - 1 - 1 u.r.SET-3B-100-170 160 1 - - - 1 1 u.r.SET-3B-100-195 195 1 1 - 1 - 2 u.r.SET-3B-100-220 220 1 1 - - 1 2 u.r.SET-3B-100-245 245 1 - 1 1 - 2 u.r.SET-3B-100-270 270 1 - 1 - 1 2 u.r.SET-3B-100-295 295 1 1 1 1 - 3 u.r.SET-3B-100-320 320 1 1 1 - 1 3 u.r.
NEW!
NEW!
Pura
plas
tPE
man
hole
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURAPLAST PE manhole accessories
Pipe connector seal
Price group 000
Art. No. Description Pipe Ø mm € / pieceIS110 Pipe connector seal 100 u.r.IS125 Pipe connector seal 125 u.r.IS160 Pipe connector seal 150 u.r.IS200 Pipe connector seal 200 u.r.IS250 Pipe connector seal 250 u.r.IS315 Pipe connector seal 300 u.r.IS400 Pipe connector seal 400 u.r.
Pipe connector sealfor groundwater installation
Price group 000
Art. No. Description Pipe Ø mm € / pieceISW110 Pipe connector seal 100 u.r.ISW125 Pipe connector seal 125 u.r.ISW160 Pipe connector seal 150 u.r.ISW200 Pipe connector seal 200 u.r.ISW250 Pipe connector seal 250 u.r.ISW315 Pipe connector seal 300 u.r.
Core bitfor pipe connection
Price group 000
Art. No. Description Pipe Ø mm € / pieceID110 Core bit 100 u.r.ID125 Core bit 125 u.r.ID160 Core bit 150 u.r.ID200 Core bit 200 u.r.ID250 Core bit 250 u.r.ID315 Core bit 300 u.r.ID400 Core bit 400 u.r.
Examples of use
PURAPLAST PE manhole DN 425 PURAPLAST PE manhole DN 1000 with standard cover
s surface s surface
NEW!
NEW! NEW!
Adaptor für core bit
Price group 000
Art. No. Description € / pieceBOHRADAPTER Adaptor for core bit u.r.
Boxle
ss sl
idin
g ga
tes
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Boxless sliding gates
Manual sliding valve made of cast iron, GG typeManual sliding gate with handle, plug type, sliding frame and plate made of GG25 grey cast iron, exchangeable bronze block seals on frame and plate, spindle, plate rollers and shafts made of stainless steel 1.4571 / 1.4404, wall seals made of wastewater-resistant Neoprene, including wall holder and handle, mounted directly on the sliding plate
Price group 098
l with flange upon request
Art. No. DN Minimum installation depth mm
Weight kg € / piece
TE-B0501-GG-150 150 360 55 u.r.TE-B0501-GG-200 200 460 65 u.r.TE-B0501-GG-250 250 560 80 u.r.TE-B0501-GG-300 300 660 95 u.r.TE-B0501-GG-350 350 760 110 u.r.TE-B0501-GG-400 400 860 140 u.r.
Manual sliding valve made of steel, ST typeManual sliding gate with handle, plug/flange type, sliding frame, plate and guides made of galvanised steel, waste-water-resistant Neoprene plate seal, wall sealing on building side (recommended: silicone), including wall holder and handle, mounted directly on the sliding plate
Price group 098
l with flange upon request
Art. No. DN Minimum installation depth mm
Weight kg € / piece
TE-C0511-ST-150 150 360 11 u.r.TE-C0511-ST-200 200 460 16 u.r.TE-C0511-ST-250 250 560 33 u.r.TE-C0511-ST-300 300 660 38 u.r.TE-C0511-ST-350 350 760 46 u.r.TE-C0511-ST-400 400 860 58 u.r.TE-C0511-ST-500 500 1060 75 u.r.TE-C0511-ST-600 600 1260 88 u.r.
Manual sliding valve made of stainless steel, A2 typeManual sliding gate with handle, plug/flange type, sliding frame, plate and guides made of stainless steel 1.4301, wastewater-resistant Neoprene plate seal, wall sealing on building side (recommended: silicone), including wall holder and handle, mounted directly on the sliding plate
Price group 098
l with flange upon request
Art. No. DN Minimum installation depth mm
Weight kg € / piece
TE-C0511-A2-150 150 360 11 u.r.TE-C0511-A2-200 200 460 16 u.r.TE-C0511-A2-250 250 560 33 u.r.TE-C0511-A2-300 300 660 38 u.r.TE-C0511-A2-350 350 760 46 u.r.TE-C0511-A2-400 400 860 58 u.r.TE-C0511-A2-500 500 1060 75 u.r.TE-C0511-A2-600 600 1260 88 u.r.
Boxle
ss sl
idin
g ga
tes
��0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Boxless sliding gates
Threaded sliding gate made of cast iron, GG typeThreaded sliding gate with spindle, plug type, sliding frame and plate made of GG25 grey cast iron, exchangeable bronze block seals on frame and plate, aluminium bronze spindle nut. Spindle, plate rollers and shafts made of stainless steel 1.4571 / 1.4404. Stainless steel spindle extension, wall seals made of wastewater-resistant Neoprene, including valve actuator, type 100
Price group 098
l with flange upon request
Art. No. DN Minimum installation depth mm
Weight kg € / piece
TE-B1001-GG-150 150 710 55 u.r.TE-B1001-GG-200 200 835 65 u.r.TE-B1001-GG-250 250 935 80 u.r.TE-B1001-GG-300 300 1035 95 u.r.TE-B1001-GG-350 350 1135 110 u.r.TE-B1001-GG-400 400 1235 140 u.r.TE-B1001-GG-500 500 1455 240 u.r.TE-B1001-GG-600 600 1695 275 u.r.
Threaded sliding gate made of hot-dip galvanised steel, ST typeThreaded sliding gate with spindle, plug type, sliding frame plate and guides made of hot-dip galvanised steel, block seals made of wastewater-resistant Neoprene, wall sealing on building side (recommended: silicone), aluminium bronze spindle nut, spindle made of stainless steel 1.4571 / 1.4404, spindle extension made of stainless steel 1.4301, including valve actuator, type 100 GST
Price group 098
l with flange upon request
Art. No. DN Minimum installation depth mm
Weight kg € / piece
TE-C2001-ST-150 150 615 15 u.r.TE-C2001-ST-200 200 690 20 u.r.TE-C2001-ST-250 250 760 42 u.r.TE-C2001-ST-300 300 890 47 u.r.TE-C2001-ST-350 350 990 57 u.r.TE-C2001-ST-400 400 1090 67 u.r.TE-C2001-ST-500 500 1330 86 u.r.TE-C2001-ST-600 600 1530 97 u.r.
Threaded sliding gate made of stainless steel 1.4301, type A2Threaded sliding gate with spindle, plug type, sliding frame plate and guides made of stainless steel 1.4301, block seals made of wastewater-resistant Neoprene, wall sealing on building side (recommended: silicone), aluminium bronze spindle nut, spindle made of stainless steel 1.4571 / 1.4404, spindle extension made of stainless steel 1.4301, including valve actuator, type 100 ST
Price group 098
l with flange upon request
Art. No. DN Minimum installation depth mm
Weight kg € / piece
TE-C2001-A2-150 150 615 15 u.r.TE-C2001-A2-200 200 690 20 u.r.TE-C2001-A2-250 250 760 42 u.r.TE-C2001-A2-300 300 890 47 u.r.TE-C2001-A2-350 350 990 57 u.r.TE-C2001-A2-400 400 1090 67 u.r.TE-C2001-A2-500 500 1330 86 u.r.TE-C2001-A2-600 600 1530 97 u.r.
Boxle
ss sl
idin
g ga
tes
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Valve actuator and accessories
Valve actuator for threaded sliding gates
Type 100 Type 100 ST and 100 GST Type 108
Coupling made of stainless steel 1.4571
Price group 098
Art. No. Material € / pieceTE-KUPPL stainless steel 1.4571 u.r.
Spindle extension stainless steel 1.4571/1.4401 no
imagePrice group 098
Art. No. Material € / piece
TE-SPINDELV stainless steel 1.4571/1.4401 u.r.
Spindle guide made of stainless steel 1.4571/1.4401
Price group 098
Art. No. Material € / piece
TE-SPINDELF stainless steel 1.4571/1.4401 u.r.
Service key 21/25 Length L = 1.200 mm
Price group 098
Art. No. Length mm € / pieceTE-N1001 1200 u.r.
Wall holder made of stainless steel 1.4571 for manual sliding gates
Price group 098
Art. No. Material € / piece
TE-WANDHALT stainless steel 1.4571 u.r.
Plug-Setmade of galvanised steelfor threades slide gates no image
Price group 098
Art. No. for DN € / pieceTE-SET1ST-15-20 150-200 u.r.TE-SET1ST-25-30 250-300 u.r.TE-SET1ST-35-60 350-600 u.r.TE-SET1ST-70 700 u.r.TE-SET1ST-80 800 u.r.
Plug-Setmade of stainless steelfor threades slide gates no image
Price group 098
Art. No. for DN € / pieceTE-SET1A4-15-20 150-200 u.r.TE-SET1A4-25-30 250-300 u.r.TE-SET1A4-35-60 350-600 u.r.TE-SET1A4-70 700 u.r.TE-SET1A4-80 800 u.r.
Back
-wat
er g
ates
and
antifl
oodi
ng va
lves
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Back-water gates
Cast iron back-water gate without pendulum bob, type GG – plug versionFrame and valve made of GG-25 , valve seal made of wastewater-resistant Neoprene, Frame seal exchangeable, made of corrosion-proof zinc-free bronze, wall seal made of wastewater-resistant Neoprene, bearing and screws made of stainless steel 1.4571 / 1.4404, Bushing made of corrosion-proof zinc-free bronze, blast cleaned SA 2,5. Zinc prime coat with 400 μm epoxy finish
Price group 098
l flange version upon request
Art. No. DN Weight kg € / pieceTE-G1020-GG-200 200 18 u.r.TE-G1020-GG-250 250 20 u.r.TE-G1020-GG-300 300 22 u.r.TE-G1020-GG-350 350 30 u.r.TE-G1020-GG-400 400 35 u.r.TE-G1020-GG-450 450 40 u.r.TE-G1020-GG-500 500 50 u.r.TE-G1021-GG-600 600 120 u.r.
Automatic cast iron back-water gate with pendulum bob, type GG – plug versionFrame and valve made of GG-25 , valve seal made of wastewater-resistant Neoprene, Frame seal exchangeable, made of corrosion-proof zinc-free bronze, wall seal made of wastewater-resistant Neoprene, bearing and screws made of stainless steel 1.4571 / 1.4404, Bushing made of corrosion-proof zinc-free bronze, blast cleaned SA 2,5. Zinc prime coat with 400 μm epoxy finish
Price group 098
l flange version upon request
Art. No. DN Weight kg € / pieceTE-G1005-GG-200 200 25 u.r.TE-G1005-GG-250 250 28 u.r.TE-G1005-GG-300 300 30 u.r.TE-G1005-GG-350 350 50 u.r.TE-G1005-GG-400 400 55 u.r.TE-G1005-GG-450 450 60 u.r.TE-G1005-GG-500 500 70 u.r.TE-G1005-GG-600 600 170 u.r.
Back-water gate made of steel, type ST hot-dip galvanised steelBack-water gate with single cover, plug/flange-version, frame and valve made of hot-dip galvanised steel, valve seal made of Neoprene, shafts made of stainless steel 1.4301
Price group 098
Art. No. DN Weight kg € / pieceTE-G1030-ST-100 100 6 u.r.TE-G1030-ST-150 150 8 u.r.TE-G1030-ST-200 200 10 u.r.TE-G1030-ST-250 250 15 u.r.TE-G1030-ST-300 300 20 u.r.TE-G1030-ST-350 350 24 u.r.TE-G1030-ST-400 400 27 u.r.TE-G1030-ST-500 500 38 u.r.TE-G1030-ST-600 600 45 u.r.
Fixed to wall by plugs
Flange connection(flange type: PN10)
Back
-wat
er g
ates
and
antifl
oodi
ng va
lves
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Back-water gate made of stainless steel, type A2 stainless steel 1.4301Back-water gate with single cover, plug/flange-version, frame and valve made of hot-dip galvanised steel, valve seal made of Neoprene, shafts made of stainless steel 1.4301
Price group 098
Art. No. DN Weight kg € / pieceTE-G1030-A2-100 100 6 u.r.TE-G1030-A2-150 150 8 u.r.TE-G1030-A2-200 200 10 u.r.TE-G1030-A2-250 250 15 u.r.TE-G1030-A2-300 300 20 u.r.TE-G1030-A2-350 350 24 u.r.TE-G1030-A2-400 400 27 u.r.TE-G1030-A2-500 500 38 u.r.TE-G1030-A2-600 600 45 u.r.
Fixed to wall by plugs
Flange connection(flange type: PN10)
Back-water gates, pipe valves
Cast iron pipe valve, “frog valve” GG type - plug/flange-versionPlug-in/flange-mounted pipe valve, frame and valve made of GG-25 cast iron, valve seals made of wastewater-resistant Neoprene, shafts and screws made of stainless steel 1.4571 / 1.4404, dual joint, blast cleaned SA 2,5. Zinc prime coat with 400 μm epoxy finish
Price group 098
Art. No. DN L S Weight kg € / pieceTE-G1003-GG-100 100 120 40 4 u.r.TE-G1003-GG-125 125 130 40 5 u.r.TE-G1003-GG-150 150 140 40 7 u.r.TE-G1003-GG-200 200 155 40 9 u.r.TE-G1003-GG-250 250 170 40 10 u.r.TE-G1003-GG-300 300 180 60 15 u.r.TE-G1003-GG-350 350 185 60 20 u.r.TE-G1003-GG-400 400 190 60 28 u.r.TE-G1003-GG-450 450 195 60 45 u.r.TE-G1003-GG-500 500 200 80 38 u.r.TE-G1003-GG-600 600 210 80 60 u.r.
Cast iron pipe valve, “frog valve” GG type - cast concrete versionPipe valve for placement in concrete, frame and valve made of GG-25 cast iron, valve seals made of wastewater-resistant Neoprene, shafts and screws made of stainless steel 1.4571 / 1.4404, bushing made of corrosion-proof zinc-free bronze, blast cleaned SA 2,5. Zinc prime coat with 400 μm epoxy finish
Price group 098
Art. No. DN DA Weight kg € / pieceTE-G1001-GG-100 100 130 4 u.r.TE-G1001-GG-125 125 155 5 u.r.TE-G1001-GG-150 150 180 7 u.r.TE-G1001-GG-200 200 230 9 u.r.TE-G1001-GG-250 250 280 10 u.r.TE-G1001-GG-300 300 330 15 u.r.
Back
-wat
er g
ates
and
antifl
oodi
ng va
lves
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Accessories
Accessories back-water gates Price group 098
Art. No. Beschreibung for DN € / pieceAccessories for cast iron back-water gatesTE-SET2ST-20-40 Plug set made of hot-dip galvanised steel 200-400 u.r.TE-SET2ST-45-60 Plug set made of hot-dip galvanised steel 450-600 u.r.TE-SET2ST-70-12 Plug set made of hot-dip galvanised steel 700-1200 u.r.TE-SET2A4-20-40 Plug set made of stainless steel 1.4571 200-400 u.r.TE-SET2A4-45-60 Plug set made of stainless steel 1.4571 450-600 u.r.TE-SET2A4-70-12 Plug set made of stainless steel 1.4571 700-1200 u.r.Accessories for steel back-water gatesTE-SET3ST-10-60 Plug set made of hot-dip galvanised steel 100-600 u.r.TE-SET3ST-70-80 Plug set made of hot-dip galvanised steel 700-800 u.r.TE-SET3ST-90-12 Plug set made of hot-dip galvanised steel 900-1200 u.r.TE-SET3A4-10-60 Plug set made of stainless steel 1.4571 100-600 u.r.TE-SET3A4-70-80 Plug set made of stainless steel 1.4571 700-800 u.r.TE-SET3A4-90-12 Plug set made of stainless steel 1.4571 900-1200 u.r.
Our range of sliding gate valves and back-water gates comprises:• sliding gate valves• Sliding gate actuators (manual and electric motor drives)• Float-controlled slide gates• Throttle gate valves• Back-water gates• Pipe flap gates• Hand stop• Channel stop• Sliding panels and stop logs
NOTE
Please ask for the special catalogue. If re-quired, we will assist you by providing expert assistance or complete installation by know-ledgeable personnel.
Back
-wat
er g
ates
and
antifl
oodi
ng va
lves
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
SCOPE OF APPLICATION
PURATOR System Mosbaek™ discharge regulators are used wherever large quantities of water may be discharged only in exactly defined maximum amounts, e.g. to observe the maximum discharge quantity from stormwater basins, backwater channels, etc. into the sewer system, water treatment plant, separation plants, absorbing wells, receiving waters, etc.
DESCRIPTION
PURATOR System Mosbaek™ discharge regulators limit the quantities discharged by creating a cyclone in the regulating device which reduces the pressure impact of the liquid inflow.
The cyclone created in the regulator increases flow resistance to a level that permits a much larger design of inlet and outlet openings. The combination of cyclone and a large free cross-section minimises the danger of congestion in the regulator.
OPERATING PRINCIPLE
As the flow rate increases, air is enclosed in the upper part of the regulator. This results in special outflow characteristics. As the pressure level rises, the outflow curve is initially still similar to that of a plain opening. Once the water head exceeds the level of h, air is pressed out of the cyclone chamber, creating a slow-down effect. The shape of the curve changes back and then reflects the slow-down.
As the pressure level recedes, the decelerated curve moves steadily downwards until the flow rate suddenly increases and the outflow path follows a non-braked pattern.
The sudden increase in the flow rate is attributable to the air enclosed in the regulator and results in excellent self-cleansing (deposits are entrained due to the increase in the flow rate).
DESIGN
PUATOR System Mosbaek™ discharge regulators are made of acid-resistant steel DIN 1.4401/1.4404. Four main types are available to match different discharge quantities, pressure levels and media:
PURATOR discharge regulatorSystem MOSBAEK™
Example of installation
u Type CY: cyclonev Type CE/H: horizontalw Type DB: double orificex Type CEN: vertical
water head H (m)
max. flow rate
increasing storage level
decreasing storage level
flow rate Q
self purification level
Back
-wat
er g
ates
and
antifl
oodi
ng va
lves
��6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Antiflooding valves
Antiflooding valvewith automatic stainless steel flap and access hole Price group 250
Art. No. Amm
Hmm DN Weight
kg € / piece
HL710 288 190 100 2,0 u.r.HL712 303 190 125 2,1 u.r.HL715 380 248 150 3,8 u.r.HL720 445 217 200 4,1 u.r.
Antiflooding valvewith automatic stainless steel flap, additional manual stop and access hole Price group 250
Art. No. Amm
Hmm DN Weight
kg € / piece
HL710.1 288 215-270 100 2,2 u.r.HL712.1 303 215-270 125 2,2 u.r.HL715.1 380 248-348 150 3,4 u.r.HL720.1 445 248-348 200 3,7 u.r.
Antiflooding valvewith automatic plastic flap and access hole Price group 250
Art. No. Lmm
Hmm
A x Bmm DN Weight
kg € / piece
371100 355 170 205 x 155 100 1,9 u.r.371125 405 230 270 x 200 125 2,0 u.r.371150 450 230 270 x 200 150 3,7 u.r.371200 530 278 353 x 248 200 4,0 u.r.
Antiflooding valvewith automatic plastic flap, additional manual stop and access hole Price group 250
Art. No. Lmm
Hmm
A x Bmm DN Weight
kg € / piece
372100 355 205 205 x 155 100 2,1 u.r.372125 405 280 270 x 200 125 2,1 u.r.372150 450 280 270 x 200 150 3,3 u.r.372200 530 328 353 x 248 200 3,6 u.r.
Antiflooding valvewith two automatic plastic flaps, additional manual stop and access hole Price group 250
Art. No. Lmm
Hmm DN Weight
kg € / piece
373050 196 80 50 0,5 u.r.
Open
Close
Back
-wat
er g
ates
and
antifl
oodi
ng va
lves
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Antiflooding valves
Antiflooding valvewith two automatic plastic flaps, additional manual stop and access hole Price group 250
Art. No. Lmm
Hmm
A x Bmm DN Weight
kg € / piece
373100 355 205 205 x 155 100 3,1 u.r.373125 405 280 270 x 200 125 3,2 u.r.373150 450 280 270 x 200 150 5,8 u.r.373200 530 328 353 x 248 200 6,1 u.r.
Antiflooding valvewith two automatic plastic flaps, additional manual stop and access holeWith plastic protective cap (for uncovered line)
Price group 250
Art. No. Lmm
Hmm DN Weight
kg € / piece
373100-10 545 343 100 6,1 u.r.373125-10 555 343 125 6,1 u.r.373150-10 585 343 150 7,9 u.r.
Antiflooding valve for wastewaterwith two automatic stainless steel flaps, additional manual stop and access hole Price group 250
Art. No. Amm
Bmm
Cmm DN Weight
kg € / piece
HL710.2 490 378 320 100 3,2 u.r.HL712.2 490 378 320 125 3,3 u.r.HL715.2 590 426 355 150 5,9 u.r.HL720.2 615 335 350 200 6,2 u.r.
Antiflooding valve for wastewater containing faeceswith electronically controlled flap, additional manual stop and access hole. Visual operating control, visual and acoustic fault indication on the electronic control unit.
Price group 250
Art. No. Amm
Bmm
Cmm DN Weight
kg € / piece
HL710.2E 490 378 320 100 6,2 u.r.HL712.2E 490 378 320 125 6,2 u.r.HL715.2E 590 426 355 150 8,0 u.r.
Antiflooding valve for wastewater containing faeceswith electronically controlled flap, additional manual stop and access hole. With plastic protective cap (for uncovered line). Control and warning device with integrated self-diagnosing system and battery buffer.
Price group 250
Art. No. Lmm
Hmm DN Weight
kg € / piece
383100 545 343 100 10,0 u.r.383125 555 343 125 10,0 u.r.383150 585 343 150 10,0 u.r.
Back
-wat
er g
ates
and
antifl
oodi
ng va
lves
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Antiflooding valves
Antiflooding valve for wastewater containing faeceswith electronically controlled flap, additional manual stop and access hole. With vertically adjustable extension unit, teles-copic. Control and warning device with integrated self-diagnosing system and battery buffer.
Price group 250
Art. No. Lmm
Hmm DN Weight
kg € / piece
383100S 545 292 - 470 100 17,0 u.r.383125S 555 285 - 465 125 17,0 u.r.383150S 585 268 - 450 150 17,0 u.r.
Antiflooding valve for wastewater containing faeceswith electronically controlled flap, additional manual stop and access hole. With pump (1kW, 230V), activated by backwa-ter. With plastic protective cap (for uncovered line). Control and warning device with integrated self-diagnosing system and battery buffer.
Price group 250
Art. No. Lmm
Hmm DN Weight
kg € / piece
328100 545 343 100 20,0 u.r.328125 555 343 125 20,0 u.r.328150 585 343 150 20,0 u.r.
Antiflooding valve for wastewater containing faeceswith electronically controlled flap, additional manual stop and access hole. With pump (1kW, 230V), activated by backwa-ter. With vertically adjustable extension unit, telescopic. Control and warning device with integrated self-diagnosing system and battery buffer.
Price group 250
Art. No. Lmm
Hmm DN Weight
kg € / piece
328100S 545 292 - 470 100 25,0 u.r.328125S 555 285 - 465 125 25,0 u.r.328150S 585 268 - 450 150 25,0 u.r.
Antiflooding valvewith automatically activated plastic flap and access hole. With pipe clamp permitting connection of all types of pipe materials. Price group 250
Art. No. DAmm
Hmm
Lmm
A x Bmm DN Weight
kg € / piece
371250 260 485 730 680 x 400 250 12,0 u.r.371300 320 490 840 530 x 460 300 15,0 u.r.371400 400 605 990 655 x 590 400 27,0 u.r.371500 510 670 1245 960 x 710 500 36,0 u.r.
Pipe
duc
ts
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Polo pipe ducts RDS
RDS pipe ductSewer shaft liner, from l = 240 + 10 mm compensating ring
Price group 375 no image
Art. No. DN/ 0D Lengthmm € / piece
RDS4130 110 110 u.r.RDS4131 125 110 u.r.RDS4132 160 110 u.r.RDS4133 200 110 u.r.RDS4134 250 110 u.r.RDS4056 110 240 + 10 u.r.RDS4057 125 240 + 10 u.r.RDS4058 160 240 + 10 u.r.RDS4059 200 240 + 10 u.r.RDS4054 250 240 + 10 u.r.
RDS pipe ductExtension unit with 2 protective shells
Price group 375 no image
Art. No. DN/ 0D Lengthmm € / piece
RDS4068 110 60 u.r.RDS4069 125 60 u.r.RDS4070 160 60 u.r.RDS4071 200 60 u.r.
RDS EVOLUTIONfor medium pipes da 19-50 mm (downward extensible to da 8 mm)
Price group 375
Art. No. Description € / piece
RDS1040EV
Polo RDS evolutionpipe duct complete
Ø1 19 - 50 mm (finned pipe 100 + 2x sealing unit Ø1 19 - 50 mm
hinged, l = 300 mm
u.r.
RDS1030EVPolo RDS evolution finned pipe with integrated flange DN 100(Ø1 8 - 50 mm), l = 300 mm
u.r.
RDS1011EV Polo RDS evolution sealing unitØ1 19 - 50 mm hinged u.r.
RDS1010EVPolo RDS evolution sealing unit
with multiple ductsØ1 8 - 18 mm hinged
u.r.
RDS1020EV Polo RDS evolution sealing unit100 blind - blind insert u.r.
Ø1 = outside diameter
RDS EVOLUTIONfor medium pipes da 50-125 mm (downward extensible up to da 160 mm)
Price group 375
Art. No. Description € / piece
RDS1041EV
Polo RDS evolutionpipe duct complete
Ø1 50 - 125 mm (finned pipe 200 + 2x sealing unit Ø1 50 - 125 mm
hinged, l = 300 mm
u.r.
RDS1031EVPolo RDS evolution finned pipe with integrated falnge DN 100(Ø1 50 - 125 mm + 160 mm)
l = 300 mmu.r.
RDS1012EV Polo RDS evolution sealing unitØ1 50 - 125 mm hinged u.r.
RDS1013EVPolo RDS evolution sealing unit
with multiple ductsØ1 160 mm hinged
u.r.
RDS1021EV Polo RDS evolution sealing unit200 blind - blind insert u.r.
Ø1 = outside diameter
RDS AidsPrice group 375 no image
Art. No. Description € / pieceRDS8985 Chamfering tool 30/40/50 u.r.RDS8972 Lubricant in bottles approx. 250g u.r.RDS8975 Lubricant in pails approx. 1 kg u.r.RDS8977 Lubricant in pails approx. 10 kg u.r.RDS8978 Manual pump for 10 kg pail u.r.
RDS8990PP welding plug for repairing holes inad-
vertently drilled into POLO-KAL NG or POLO KAL 3S drain pipes
(the required PP manual welding tool is made available upon request against a rental charge)
u.r.
��0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Publ
ic wa
ter s
uppl
y
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Table of contentsInfiltration, drainage, cable guard
Infiltration 132
Infil
tratio
n
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Drain Wells
DRAIN WELLSwithout step irons Price group 091
Art. No.Detention chamber
m³
max. area exposed to rainfall m²
Inner Ø D m
Wall thick-nesscm
Inlet depthZt m
Insertion depthEt m
Weight t
weight of largest
part t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
SIR-10-115 2,19 115 1,00 7 1,02 1,76 1,1 0,35 u.r. u.r. u.r.SIR-10-140 2,74 140 1,00 7 1,02 2,02 1,2 0,35 u.r. u.r. u.r.SIR-10-165 3,39 165 1,00 7 1,02 2,27 1,4 0,35 u.r. u.r. u.r.SIR-10-190 3,88 190 1,00 7 1,02 2,53 1,5 0,35 u.r. u.r. u.r.
SIR-15-190 3,55 190 1,50 8 0,93 1,69 1,7 0,58 u.r. u.r. u.r.SIR-15-230 4,37 230 1,50 8 0,93 1,95 2,0 0,58 u.r. u.r. u.r.SIR-15-275 5,15 275 1,50 8 0,93 2,20 2,2 1,02 u.r. u.r. u.r.SIR-15-320 5,96 320 1,50 8 0,93 2,46 2,5 1,02 u.r. u.r. u.r.SIR-15-360 6,74 360 1,50 8 0,93 2,71 2,7 1,02 u.r. u.r. u.r.SIR-15-400 7,56 400 1,50 8 0,93 2,97 3,0 1,02 u.r. u.r. u.r.SIR-15-440 8,34 440 1,50 8 0,93 3,22 3,2 1,02 u.r. u.r. u.r.SIR-15-480 9,16 480 1,50 8 0,93 3,48 3,5 1,02 u.r. u.r. u.r.
SIR-20-290 5,15 290 2,00 9 1,04 1,78 2,6 1,02 u.r. u.r. u.r.SIR-20-350 6,43 350 2,00 9 1,04 2,04 3,0 1,11 u.r. u.r. u.r.SIR-20-420 7,55 420 2,00 9 1,04 2,28 3,4 1,47 u.r. u.r. u.r.SIR-20-480 8,93 480 2,00 9 1,04 2,54 3,8 1,11 u.r. u.r. u.r.SIR-20-550 10,14 550 2,00 9 1,04 2,79 4,1 1,47 u.r. u.r. u.r.SIR-20-620 11,42 620 2,00 9 1,04 3,05 4,5 1,47 u.r. u.r. u.r.SIR-20-680 12,65 680 2,00 9 1,04 3,29 4,8 1,47 u.r. u.r. u.r.SIR-20-750 13,90 750 2,00 9 1,04 3,55 5,2 1,47 u.r. u.r. u.r.
SIR-25-400 7,21 400 2,50 9 1,28 2,02 3,6 1,60 u.r. u.r. u.r.SIR-25-500 9,06 500 2,50 9 1,28 2,28 4,0 1,60 u.r. u.r. u.r.SIR-25-590 10,84 590 2,50 9 1,28 2,52 4,5 1,85 u.r. u.r. u.r.SIR-25-690 12,58 690 2,50 9 1,28 2,78 5,0 1,60 u.r. u.r. u.r.SIR-25-780 14,45 780 2,50 9 1,28 3,03 5,4 1,85 u.r. u.r. u.r.SIR-25-870 16,30 870 2,50 9 1,28 3,29 5,9 1,85 u.r. u.r. u.r.SIR-25-970 18,07 970 2,50 9 1,28 3,53 6,3 1,85 u.r. u.r. u.r.SIR-25-1060 19,93 1060 2,50 9 1,28 3,79 6,8 1,85 u.r. u.r. u.r.1 max. area exposed to rainfall relative to rain intensity according to Bodenseher and very well-draining soill different inlet depths upon request
Appropriate dimensions of drain well to be calculated by an expert!
Calculation according to ÖNORM
B2506, Part 1 dated 1 June 2000
INSPECTION and MAINTENANCE: Ask for our maintenance service offers!
Infil
tratio
n
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Drain Wells
DRAIN WELLSwith step irons Price group 091
Art. No.Detention chamber
m³
max. area exposed to rainfall m²
Inner Ø D m
Wall thick-nesscm
Inlet depthZt m
Insertion depthEt m
Weight t
weight of largest
part t
€ / piece30 kN
€ / piece125 kN
€ / piece400 kN
SIR/ST-10-115 2,19 115 1,00 7 1,02 1,96 1,2 0,36 u.r. u.r. u.r.SIR/ST-10-140 2,74 140 1,00 7 1,02 2,27 1,4 0,36 u.r. u.r. u.r.SIR/ST-10-165 3,39 165 1,00 7 1,02 2,57 1,6 0,36 u.r. u.r. u.r.SIR/ST-10-190 3,88 190 1,00 7 1,02 2,88 1,7 0,36 u.r. u.r. u.r.
SIR/ST-15-190 3,46 190 1,50 8 0,60 1,34 1,9 0,75 u.r. u.r. u.r.SIR/ST-15-230 4,28 230 1,50 8 0,60 1,60 2,1 0,75 u.r. u.r. u.r.SIR/ST-15-275 5,06 275 1,50 8 0,60 1,85 2,4 0,75 u.r. u.r. u.r.SIR/ST-15-320 5,87 320 1,50 8 0,60 2,11 2,6 0,75 u.r. u.r. u.r.SIR/ST-15-360 6,66 360 1,50 8 0,60 2,36 2,9 0,75 u.r. u.r. u.r.SIR/ST-15-400 7,47 400 1,50 8 0,60 2,62 3,1 0,75 u.r. u.r. u.r.SIR/ST-15-440 8,25 440 1,50 8 0,60 2,87 3,4 0,75 u.r. u.r. u.r.SIR/ST-15-480 9,08 480 1,50 8 0,60 3,13 3,6 0,75 u.r. u.r. u.r.
SIR/ST-20-290 5,15 290 2,00 9 0,60 1,34 2,4 0,75 u.r. u.r. u.r.SIR/ST-20-350 6,43 350 2,00 9 0,60 1,59 2,7 1,11 u.r. u.r. u.r.SIR/ST-20-420 7,55 420 2,00 9 0,60 1,84 3,1 1,47 u.r. u.r. u.r.SIR/ST-20-480 8,93 480 2,00 9 0,60 2,10 3,5 1,11 u.r. u.r. u.r.SIR/ST-20-550 10,14 550 2,00 9 0,60 2,35 3,8 1,47 u.r. u.r. u.r.SIR/ST-20-620 11,42 620 2,00 9 0,60 2,60 4,2 1,47 u.r. u.r. u.r.SIR/ST-20-680 12,65 680 2,00 9 0,60 2,85 4,6 1,47 u.r. u.r. u.r.SIR/ST-20-750 13,90 750 2,00 9 0,60 3,11 4,9 1,47 u.r. u.r. u.r.
SIR/ST-25-400 7,21 400 2,50 9 0,70 1,44 4,0 2,04 u.r. u.r. u.r.SIR/ST-25-500 9,06 500 2,50 9 0,70 1,69 4,5 2,04 u.r. u.r. u.r.SIR/ST-25-590 10,84 590 2,50 9 0,70 1,94 5,0 2,04 u.r. u.r. u.r.SIR/ST-25-690 12,58 690 2,50 9 0,70 2,20 5,4 2,04 u.r. u.r. u.r.SIR/ST-25-780 14,45 780 2,50 9 0,70 2,45 5,9 2,04 u.r. u.r. u.r.SIR/ST-25-870 16,30 870 2,50 9 0,70 2,70 6,3 2,04 u.r. u.r. u.r.SIR/ST-25-970 18,07 970 2,50 9 0,70 2,95 6,8 2,04 u.r. u.r. u.r.SIR/ST-25-1060 19,93 1060 2,50 9 0,70 3,21 7,3 2,04 u.r. u.r. u.r.1 max. area exposed to rainfall relative to rain intensity according to Bodenseher and very well-draining soil2 Please note: Weight and largest unit weight vary with the load class (data in table applicable to 30 kN)l different inlet depths upon request
INSPECTION and MAINTENANCE: Ask for our maintenance service offers!
Appropriate dimensions of drain well to be calculated by an expert!
Calculation according to ÖNORM
B2506, Part 1 dated 1 June 2000
weight of largest partSIR/ST-15 1,0 tSIR/ST-20 1,8 tSIR/ST-25 2,8 t
Infil
tratio
n
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURABOX seepage block
ADVANTAGES• Combines maximum storage capability with enormous stability for subterranean application• The natural water cycle is maintained and load on sewers is reduced• Variable, low-cost and low-weight system• No loss of usable area due to underground installation• Storage capacity up to 95% of total volume• Quick and easy to install
The PURABOX seepage block is an extensive, close to the surface drainage system for decentralized seepage and pondage in all areas as per RAL quality standards. The mod-ular design allows time optimized installation, no gravel needed (replaces gravel bed). Single blocks are interconnected with each other in horizontal and vertical dimension with connection clips (horizontal) and plug connectors (vertical) to avoid stowing and moving.The installation can be done in up to five layers, is accessible up to SLW 60. Installation is done with use of geotextile.
Total volume of a single box is 200 Liter (volume ≥ 95 %),
PURABOX seepage blocks
Price group 000
Art. No. # Description Dimensions € / piece
PURABOX seepage block V=1000 x 500 x 400 = 0,2 m³ u.r.PURABOX-CLIPSE u connection clips (horizontal) u.r.PURABOX-STECKV v plug connectors (vertical) u.r.PURABOX-ANSCHL connection sleeve DN 150 u.r.PURABOX-BELÜFT w plastic blower and exhaust DN 100 u.r.
PURABOX-KS400 manhole for controlling and ventilisation withmanhole top class A with dirt pan DN 400, H = 1500 mm u.r.
PURABOX-GEOTEX geotextile GRK 3, 233 g/m² L x B = 100m x 5,15m u.r.
Example of use
Infil
tratio
n
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Purator D-RaincleanDrain pit with substrate forms active layer of soil
Conforms to ATV standard A 138 / ÖNORM B 2506
for polluted surface runoff
PURATOR Rainclean Price group 000
Art. No. Description Dimensions €
RAINCLEAN-OF plastic drain channel with substrate, open type 400 x circa 399 x 500B x H x L (mm) u.r.
RAINCLEAN-PKW plastic drain channel with substrate, open typeincl. frame and grating (casting), trafficable
400 x circa 470 x 500B x H x L (mm) u.r.
RAINCLEAN-ENDSET-OF End units left + right incl. substrate 400 x circa 399 x 250total length = 500 mm u.r. / Set
RAINCLEAN-ENDSET-PKW End units left + right incl. substrate and gully grates 400 x circa 470 x 250total length = 500 mm u.r. / Set
ADVANTAGES• groundwater is protected through filtration,• adsorption and retention, ion exchange, precipitation and biological degradation• space-saving, easy and safe installation• can be trafficked by lorries• meets requirements of ATV 138, ÖNORM B 2506
Certified and registered system!
Examples of use
Infil
tratio
n
��6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURASORP - adsorption filter for storm waterconforming to City of Vienna MA 45 technical guidelines, consisting of:
• compact design sludge trap with buffer reservoir and prefilter• drain well composed of concrete rings• activated carbon container made of plastic with distributor, fine filter inserts and activated carbon fill• storm water sampling point• excessive backwater triggers automatic emergency overflow
VARIANT: Anti-buoyancy protection in case
of high groundwater table
PURASORP - adsorption filter for storm waterconforming to City of Vienna MA 45 technical guidelines Price group 092
Art. No.max. area
exposed to rainfall m²
Inner Ø D1
m
Inner Ø D2
m
Wall thicknesscm
s1/s2 cm
Inlet depthZt1 m
Insertion depthEt1 m
Insertion depthEt2 m
Weight t
weight of largest
part t€ / piece
PS-260 260 2,05 1,50 8/7 0,66 2,04 2,71 7,1 3,0 u.r.PS-490 490 2,50 1,50 9/7 0,62 2,04 2,95 9,8 4,0 u.r.PS-780 780 2,50 1,50 9/7 0,61 2,62 3,48 11,8 5,0 u.r.PS-1040 1040 2,70 1,50 9/7 0,69 2,89 3,74 13,4 6,4 u.r.PS-1330 1330 2,70 1,50 9/7 0,69 3,39 4,24 15,3 7,4 u.r.1 Rain yield conforming to City of Vienna MA 45 technical guidelinesl all systems available in loading classes 30 kN, 125 kN and 400 kN
other inlet depths or sludge trap in ring design for larger areas exposed to rainfall
INSPECTION and MAINTENANCE: Ask for our maintenance service offers!
Sludge trap Cesspool
Infil
tratio
n
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Filters
Adsorption filter set for retrofitting existing drain wellswith AC mats, nonwoven fabric cover and tension ring Price group 000
Art. No. Drain well diameter m € / piece
AFS-10-A-3SP 1,00 u.r.AFS-15-A-3SP 1,50 u.r.AFS-20-A-3SP 2,00 u.r.AFS-25-A-3SP 2,50 u.r.
Activated carbon filter for retrofitting existing drain wellswith 20 cm filter bed, nonwoven fabric cover and tension ring Price group 000
Art. No. Drain well diameter m € / piece
AFS-10-AK20 1,00 u.r.AFS-15-AK20 1,50 u.r.AFS-20-AK20 2,00 u.r.AFS-25-AK20 2,50 u.r.
A in mm
B in mm
C in mm
D in mm
E in mm
F in mm
G in mm
670 540 475 390 325 275 320670 540 525 980 325 275 880670 540 525 980 325 275 880670 540 575 980 325 275 880
Filter Rainwater Inlet Sewer Inlet Cistern Inlet Screen mesh size
min. gully Ø mm max. flow rate connectable roof area
VF2 1 x DN 200 1 x DN 200 1 x DN 150 550 my 1000 25,5 l/s 850 m²VF3 1 2 x DN 200 2 1 x DN 200 1 x DN 150 550 my 1200 33,0 l/s 1100m²VF4 2 x DN 250 2 1 x DN 250 1 x DN 150 550 my 1200 51,5 l/s 1700m²VF6 2 x DN 250 2 1 x DN 250 1 x DN 200 550 my 1200 70,5 l/s 2350m²1 Only one side of volume filter VF3 is fitted with a ribbed unit.2 The two inlets do not have to be used but increase filter capacity. Upon request, the appropriate panels will be enclosed.
VOLUME FILTER
Infil
tratio
n
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
l container with coverborehole for in/outlet preparedtechnical piping prepared
l filter-syphon-module
l supply slow-down
Rainwater utilisation - basic set
Rainwater utilisation basic setwith concrete container, compact design, manhole top 30 kN and 125 kN Pricegroup 092
Art. No. Capacity m³
Inner ØD m
Wall thickness s cm
InletDN mm
Inlet depth Zt m
Insertion depth Et m
Weight t
weigth of largest part t
€ / piece30 kN
€ / piece125 kN
RWN-GAPA3 3,0 1,50 10 100 0,86 2,67 3,8 3,1 u.r. u.r.RWN-GAPA5 5,0 2,00 10 100 0,93 2,74 5,9 4,7 u.r. u.r.RWN-GAPA8 8,0 2,50 12 100 1,18 2,98 8,2 6,5 u.r. u.r.l different inlet depths upon request
Plastic tank PE, basic setmax. coverage 100 cm (container peak), accessible manhole cover
Art. No. Capacity m³
Ø D m
Insertion depth Et m
Lm € / piece
3101490-A 2,0 1,26 1,59 2,14 u.r.3101491-A 3,0 1,45 1,78 2,45 u.r.3101492-A 4,0 1,69 2,00 2,45 u.r.l different inlet depths upon request
Rainwater utilisation - basic set for garden watering, consisting of:
Accessoriesl Forta Duo pump Suction and force pump with lighting set 230V, 50Hz, 1.100 Watt, H=41m, Q=3,1 m³/h, Connection 1“, integrated flow guard, protection against dry running Art. No.: 3101228 u.r.
l Taking set consisting of plastic manhole Ø 15cm 1/2“ hose connection, 15m plastic pipe PE DN 25 with clamp fitting Art. No.: 3101610 u.r.
l further accessories upon request
Infil
tratio
n
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
l container with manhole cover height adjustable dome (only PE)
borehole for in/outlet prepared technical piping prepared
l rainwater suction module with floating taking
l filter-syphon-module
l supply slow-down
Rainwater utilisation - complete set
Rainwater utilisation complete setwith concrete container, compact design, manhole top 30 kN and 125 kN Pricegroup 092
Art. No. Capacity m³
Inner ØD m
Wall thickness s cm
InletDN mm
Inlet depth Zt m
Insertion depth Et m
Weight t
weigth of largest part t
€ / piece30 kN
€ / piece125 kN
RWN-HAGAPA3 3,0 1,50 10 100 0,86 2,67 3,8 3,1 u.r. u.r.RWN-HAGAPA5 5,0 2,00 10 100 0,93 2,74 5,9 4,7 u.r. u.r.RWN-HAGAPA8 8,0 2,50 12 100 1,18 2,98 8,2 6,5 u.r. u.r.l different inlet depths upon request
Plastic tank PE, basic setmax. coverage 100 cm (container peak), accessible manhole cover
Art. No. Capacity m³
Ø D m
Insertion depth Et m
Lm € / piece
3101051 4,0 1,69 2,45 - 2,65 2,45 u.r.3101052 5,0 1,91 2,67 - 2,87 2,45 u.r.3101053 7,5 2,20 2,95 - 3,15 2,80 u.r.
Rainwater utilisation - complete set for domestic use and garden watering, consisting of:
Accessoriesl Labelling set consisting of engravure plate, adhesive film, 10m guarding band, adhesive label, pipe marker Art. No.: 34000700 u.r.
l Taking set consisting of plastic manhole Ø 15cm 1/2“ hose connection with shut-off, 15m plastic pipe PE DN 25 with clamp fitting Art. No.: 3101610 u.r.
l further accessories upon request
��0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Build
ing
drain
age
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Table of contentsBuilding drainage
Roof outlets 142
Floor drains 145
Stainless steel channels and trays 153
Basement drains and heating oil stops 158
Rainwater drains 160
Roof
out
lets
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Basic body made of stainless steel 1.4571 with clamp flange Price group 142
Outlet vertical Outlet horizontal
Art. No. DN Type € / piece76.11.70 70 without heat insulation u.r.76.21.70 70 with heat insulation u.r.76.31.70 70 with heat insulation and heater u.r.76.11.00 100 without heat insulation u.r.76.21.00 100 with heat insulation u.r.76.31.00 100 with heat insulation and heater u.r.76.11.25 125 without heat insulation u.r.76.21.25 125 with heat insulation u.r.76.31.25 125 with heat insulation and heater u.r.76.11.50 150 without heat insulation u.r.76.21.50 150 with heat insulation u.r.76.31.50 150 with heat insulation and heater u.r.
Art. No. DN Type € / piece76.51.70 70 without heat insulation u.r.76.61.70 70 with heat insulation u.r.76.71.70 70 with heat insulation and heater u.r.76.51.00 100 without heat insulation u.r.76.61.00 100 with heat insulation u.r.76.71.00 100 with heat insulation and heater u.r.76.51.25 125 without heat insulation u.r.76.61.25 125 with heat insulation u.r.76.71.25 125 with heat insulation and heater u.r.76.51.50 150 without heat insulation u.r.76.61.50 150 with heat insulation u.r.76.71.50 150 with heat insulation and heater u.r.
Technical details: heat insulation with stainless steel case, heater 230V/10 Watt automatic control
FERROTECH® - cast iron roof outlets DN 70/100
Basic body made of GG25 grey cast iron with clamp flange Price group 142
Outlet vertical Outlet horizontal
Art. No. DN Type € / piece67.40.00 70 without heat insulation u.r.67.40.10 70 with heat insulation u.r.67.40.20 70 with heat insulation and heater u.r.68.40.00 100 without heat insulation u.r.68.40.10 100 with heat insulation u.r.68.40.20 100 with heat insulation and heater u.r.
Art. No. DN Type € / piece67.70.00 70 without heat insulation u.r.67.70.10 70 with heat insulation u.r.67.70.20 70 with heat insulation and heater u.r.68.70.00 100 without heat insulation u.r.68.70.10 100 with heat insulation u.r.68.70.20 100 with heat insulation and heater u.r.
Technical details: heat insulation with stainless steel case, heater 230V/10 Watt automatic control
Leaf/debris trapplastic, PP
Price group 142
Art. No. € / piece67.11.00 u.r.
Insulating unit made of foamed glass
Price group 142
Art. No. Description Drain € / piece68.40.01 for basic body h = 130 mm vertical u.r.68.40.02 for basic body h = 130 mm horizontal u.r.68.11.86 for extension h = 130 mm vertical u.r.
All basic bodies shown on this page can be combined with extensions and accessories shown on pages 147 - 153
CHROMTECH® - cast iron roof outlets DN 70/100/125/150NEW!
with heater
Roof
out
lets
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Polyurethane roof outletwith factory-fixed skirt membrane Art. No. Description DN Weight
(kg)Price group
€ / piece
heat-insulated
also available factory-welded skirt membranes made of:• PIB• EPDM• ECB• SARNAFIL• AUSTROPLANor without factory-fixed skirt membrane
with bituminous membrane057651000 h 230 mm, d 75 mm 70 2,0 253 u.r.057663000 h 245 mm, d 110 mm 100 2,1 253 u.r.057675000 h 250 mm, d 125 mm 125 3,8 253 u.r.057687000 h 250 mm, d 160 mm 150 4,1 253 u.r.with PVC skirt membrane057297000 h 230 mm, d 75 mm 70 2,0 253 u.r.057302000 h 245 mm, d 110 mm 100 2,1 253 u.r.057314000 h 250 mm, d 125 mm 125 3,8 253 u.r.057326000 h 250 mm, d 160 mm 150 4,1 253 u.r.
as above, including ice guardfor automatic heating below 1-3° C
with bituminous membrane057728000 h 230 mm, d 75 mm 70 2,0 253 u.r.057730000 h 245 mm, d 110 mm 100 2,1 253 u.r.057742000 h 250 mm, d 125 mm 125 3,8 253 u.r.057754000 h 250 mm, d 160 mm 150 4,1 253 u.r.with PVC skirt membrane057417000 h 230 mm, d 75 mm 70 2,0 253 u.r.057429000 h 245 mm, d 110 mm 100 2,1 253 u.r.057431000 h 250 mm, d 125 mm 125 3,8 253 u.r.057443000 h 250 mm, d 160 mm 150 4,1 253 u.r.
Plastic roof outletsOu
tlet v
ertic
al
Polyurethane roof outletwith factory-fixed skirt membrane Art. No. Description DN Weight
(kg)Price group € / piece
heat-insulated
also available factory-welded skirt membranes made of:• PIB• EPDM• ECB• SARNAFIL• AUSTROPLANor without factory-fixed skirt membrane
with bituminous membrane057699000 h 115 mm, d 75 mm 70 2,0 253 u.r.057704000 h 147 mm, d 77 mm 100 2,1 253 u.r.057716000 h 147 mm, d 92 mm 125 3,8 253 u.r.with PVC skirt membrane057118000 h 115 mm, d 75 mm 70 2,0 253 u.r.057120000 h 147 mm, d 77 mm 100 2,1 253 u.r.057132000 h 147 mm, d 92 mm 125 3,8 253 u.r.
as above, including ice guardfor automatic heating below 1-3° C
with bituminous membrane057766000 h 115 mm, d 75 mm 70 2,0 253 u.r.057778000 h 147 mm, d 77 mm 100 2,1 253 u.r.057780000 h 147 mm, d 92 mm 125 3,8 253 u.r.with PVC skirt membrane057194000 h 115 mm, d 75 mm 70 2,0 253 u.r.057209000 h 147 mm, d 77 mm 100 2,1 253 u.r.057211000 h 147 mm, d 92 mm 125 3,8 253 u.r.
Outle
t hor
izont
al
Roof
out
lets
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Accessories for plastic roof outlets, HL plastic roof outlets
Clamping collarconsisting of two aluminium rings, one rolling ring, one sealing ring, to clamp on to 1 to 2 mm roof membranes
Price group 253
Art. No. DN Weight (kg) € / piece289462000 100 0,5 u.r.
Polyurethane add-on unitwith factory-fixed skirt membrane, continuously adjustable
Price group 253
Art. No. Adjustable range € / piecewith bituminous membrane057792000 60 - 160 mm u.r.057792200 160 - 240 mm u.r.
with PVC skirt membrane057584000 60 - 160 mm u.r.057584200 160 - 240 mm u.r.
Roof deck kitthree-piece set of aluminium die cast, componentscontinuously adjustable between 33 mm and 106 mm
Price group 253
Art. No. DN Weight (kg) € / piece057560000 100 0,5 u.r.
grating
grating support
heigth setup ring
Flashing unit for building rehabilitationfor installation of add-on unit in existing roof gullies with inlet cross-section of 125 mm
Price group 253
Art. No. DN Weight (kg) € / piecewith bituminous membrane649545100 100 2,1 u.r.649545140 125 3,8 u.r.649545165 150 4,1 u.r.
with PVC skirt membrane649557100 100 2,1 u.r.649557140 125 3,8 u.r.649557165 150 4,1 u.r.
HL plastic roof outletswith heat-insulated outlet body Price group 250
Outlet DN 75vertical
Outlet DN 110vertical
Outlet DN 125vertical
Outlet DN 160vertical
Outlet DN 75/110horizontal
Art. No. € / pieceHL62-70 u.r.
Art. No. € / pieceHL62-110 u.r.
Art. No. € / pieceHL62-125 u.r.
Art. No. € / pieceHL62-160 u.r.
Art. No. € / pieceHL64 u.r.
with
clam
ping
colla
r
HL plastic roof outletswith heat-insulated outlet body and bitumen collar (H) Price group 250
Outlet DN 75vertical
Outlet DN 110vertical
Outlet DN 125vertical
Outlet DN 160vertical
Outlet DN 75/110horizontal
Art. No. € / pieceHL62H-75 u.r.
Art. No. € / pieceHL62H-110 u.r.
Art. No. € / pieceHL62H-125 u.r.
Art. No. € / pieceHL62H-160 u.r.
Art. No. € / pieceHL64H u.r.
with
bitu
min
ous c
ollar
Floo
r Dra
ins
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
FERROTECH® one-piece cast iron floor drains
Cast iron sewer coverwith rivet-mounted odour trap
Price group 70
Art. No. Description DN Weightkg € / piece
1016A100 ¨ a 115 mm 30 2,0 u.r.1016A120 ¨ a 135 mm 40 2,6 u.r.1016A150 ¨ a 170 mm 50 4,0 u.r.1016A200 ¨ a 205 mm 50 5,6 u.r.
Cast iron sewer coverwith cast-on odour trapexchangeable grating
Price group 70
Art. No. Description DN Weightkg € / piece
1016B100 ¨ a 100 mm 30 1,6 u.r.1016B120 ¨ a 140 mm 40 2,5 u.r.1016B150 ¨ a 170 mm 50 3,8 u.r.1016B200 ¨ a 210 mm 50 5,3 u.r.1016B250 ¨ a 260 mm 70 12,0 u.r.1016B300 ¨ a 320 mm 70 20,0 u.r.
Cast iron floor drainwith fixed knee pipe with cleaning plug
Price group 70
Art. No. # Description DN Weightkg € / piece
1018A u ¨ a 160 mm 70 5,3 u.r.1018B u ¨ a 180 mm 70 6,8 u.r.1035C1 v Ø a 220 mm 100 14,0 u.r.
u v
Cast iron basement drainwith odour trap, black prime-coated
Price group 140
Art. No. # Description Class Weightkg € / piece
140-5000-00-00u DN 100, outlet 3° K 3 5,3 u.r.140-5001-00-00v DN 100, outlet 1,5° L 15 6,8 u.r.140-5002-00-00 - DN 100, outlet 20° L 15 14,0 u.r.
u v
Cast iron floor drainwithout odour trap, black prime-coated Price group 140
Art. No. # Description Class Weightkg € / piece
140-5194-10-00u DN 100 M 125 11,5 u.r.140-5194-20-00u DN 125 M 125 11,5 u.r.140-5194-30-00u DN 150 M 125 11,5 u.r.140-5095-80-00v h 46 mm - 3,8 u.r.140-5193-00-00w DN 100 L 15 10,0 u.r.140-5191-00-00x DN 100 L 15 10,0 u.r.140-5191-05-00x DN 100 M 125 10,0 u.r.140-5192-00-00x DN 150 L 15 11,5 u.r.140-5192-05-00x DN 150 M 125 11,5 u.r.
140-5190-00-00y DN 100, with flashing L 15 11,3 u.r.
140-5190-05-00y DN 100, with flashing M 125 11,3 u.r.
140-6199-00-00z DN 100 M 125 13,5 u.r.140-5188-00-00z DN 150 M 125 46,0 u.r.
w
u v
x
y z
Floo
r Dra
ins
��6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
FERROTECH® - cast iron floor drains DN 70/80/100with drain body Ø150 conforming to ÖNorm-EN1253
Extension with cast iron grating, prime-coatedand collar with weep holes
Price group 142Art. No. Class Size € / piece65.71.48 L15 £ 150 u.r.65.71.48-1 M125 £ 150 u.r.
Extension for thin mortar bed with slotted stainless steel grating and triple lip sealPrice group 142Art. No. Class Size € / piecePlastic extenstion60.71.46 K3 £ 150 u.r.60.71.46-1 L15 £ 150 u.r.Stainless steel extenstion60.71.47 K3 £ 150 u.r.60.71.47-1 L15 £ 150 u.r.
Extension with stainless steel grating and collar with weep holes
Price group 142Art. No. Class Size € / piece60.71.41 L15 £ 150 u.r.60.71.42 M125 £ 150 u.r.61.71.41-2 L15 £ 200 u.r.61.71.42-3 M125 £ 200 u.r.
Extension with slotted stainless steel grating, plastic adapter and collar with weep holesPrice group 142Art. No. Class Size € / piece60.71.43 K3 £ 150 u.r.60.71.43-1 L15 £ 150 u.r.61.71.43-2 K3 £ 200 u.r.61.71.43-3 L15 £ 200 u.r.
Extension with slotted stainless steel grating and collar with weep holes
Price group 142Art. No. Class Size € / piece60.71.44 K3 £ 150 u.r.60.71.44-1 L15 £ 150 u.r.61.71.44-2 K3 £ 200 u.r.61.71.44-3 L15 £ 200 u.r.
Plastic extension with slotted stainless steel grating and collar with weep holes
Price group 142
Art. No. Class Size € / piece60.71.45 K3 £ 150 u.r.60.71.45-1 L15 £ 150 u.r.61.71.45-2 K3 £ 200 u.r.61.71.45-3 L15 £ 200 u.r.
Basic body made of GG25 grey cast ironprime-coated, with removable PP odour trap Price group 142
vertical, with glued flashing vertical, with clamp flange
Art. No. DN € / piece65.41.00 70 u.r.65.41.00-80 80 u.r.65.51.00 100 u.r.
Art. No. DN € / piece65.41.20 70 u.r.65.41.20-80 80 u.r.65.51.20 100 u.r.
horizontal, with glued flange horizontal, with clamp flange
Art. No. DN € / piece65.61.00 70 u.r.65.61.00-80 80 u.r.65.81.00 100 u.r.
Art. No. DN € / piece65.61.20 70 u.r.65.61.20-80 80 u.r.65.81.20 100 u.r.
Floo
r Dra
ins
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
FERROTECH® - cast iron floor drains DN 100with drain body Ø205 conforming to ÖNorm-EN1253
Cast iron add-on unit Price group 142
Art. No. # for outlet body Typ € / piece65.71.05 - Ø 150 with glued flange u.r.65.71.25 u Ø 150 with clamp flange u.r.66.71.05 - Ø 205 with glued flange u.r.66.71.25 v Ø 205 with clamp flange u.r.
u v
Plastic add-on unit Price group 142
Art. No. # for outlet body Typ € / piece65.71.05PVC u Ø 150 with glued flange u.r.65.71.25PVC v Ø 150 with clamp flange u.r.
u v
Accessories Price group 142
Art. No. Description for outlet body € / piece60.47.28 Mud basket Ø 150 u.r.60.71.30 Seal with backflow protection Ø 150 u.r.60.71.35 Grating screws Ø 150 u.r.61.47.28 Mud basket Ø 205 u.r.61.71.30 Seal with backflow protection Ø 205 u.r.61.71.35 Grating screws Ø 205 u.r.l Side inlet , epoxy-coated upon request
Odour trap for fire protection F90
Price group 142
Art. No. for outlets € / piece60.71.11 60.40... - 65.41... DN 70, outlet body Ø 150 u.r.60.71.12 60.50... - 65.51... DN 100, outlet body Ø 150 u.r.61.71.11 61.40... - 66.41... DN 100, outlet body Ø 205 u.r.
Extension with cast iron grating, prime-coatedand collar with weep holes
Price group 142Art. No. Class Size € / piece66.71.48 L15 £ 200 u.r.66.71.48-1 M125 £ 200 u.r.
Extension with slotted stainless steel grating, plastic adapter and collar with weep holesPrice group 142Art. No. Class Size € / piece66.71.43 K3 £ 200 u.r.66.71.43-1 L15 £ 200 u.r.
Plastic extension with slo-tted stainless steel grating and collar with weep holes
Price group 142Art. No. Class Size € / piece66.71.45 L15 £ 200 u.r.66.71.45-1 M125 £ 200 u.r.
Extension with stainless steel grating and collar with weep holes
Price group 142Art. No. Class Size € / piece66.71.41 L15 £ 200 u.r.66.71.42 M125 £ 200 u.r.
Extension with slotted stainless steel grating and collar with weep holes
Price group 142Art. No. Class Size € / piece66.71.44 L15 £ 200 u.r.66.71.44-1 M125 £ 200 u.r.
Extension for thin mortar bed with slotted stainless steel grating and triple lip sealPrice group 142Art. No. Class Size € / piece66.71.46 K3 £ 200 u.r.66.71.46-1 L15 £ 200 u.r.
Basic body of GG25 grey cast ironprime-coated, with removable PP odour trap Price group 142
vertical, with glued flange vertical, with clamp flange
Art. No. DN € / piece66.41.00 100 u.r.
Art. No. DN € / piece66.41.20 100 u.r.
Floo
r Dra
ins
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Extension with stainless steel grating and collar with weep holes
Price group 231
Art. No. Class Size € / piece70.71.41 L15 £ 150 u.r.70.71.42 M125 £ 150 u.r.71.71.41-2 L15 £ 200 u.r.71.71.42-3 M125 £ 200 u.r.
Extension with stain-less steel treadplate and collar with weep holes
Price group 231
Art. No. Class Size € / piece70.71.43 M125 £ 150 u.r.
Extension with slotted stainless steel grating and collar with weep holes
Price group 231
Art. No. Class Size € / piece70.71.44 K3 £ 150 u.r.70.71.44-1 L15 £ 150 u.r.71.71.44-2 K3 £ 200 u.r.71.71.44-3 L15 £ 200 u.r.
Plastic extension with slo-tted stainless steel grating and collar with weep holes
Price group 231
Art. No. Class Size € / piece70.71.45 K3 £ 150 u.r.70.71.45-1 L15 £ 150 u.r.71.71.45-2 K3 £ 200 u.r.71.71.45-3 L15 £ 200 u.r.
Extension with slotted grating, plastic adapter and collar with weep holes
Price group 231Art. No. Class Size € / pieceStainless steel extenstion70.37.01 K3 £ 150 u.r.70.37.02 L15 £ 150 u.r.Plastic extenstion70.37.03 K3 £ 150 u.r.70.37.04 L15 £ 150 u.r.
Extension for thin mortar bed with slotted stainless steel grating and triple lip sealPrice group 231Art. No. Class Size € / piecePlastic extenstion70.37.27 K3 £ 150 u.r.70.37.28 L15 £ 150 u.r.Stainless steel extenstion70.37.29 K3 £ 150 u.r.70.37.29-1 L15 £ 150 u.r.
CHROMTECH® stainless steel floor drains DN 50/70/80/100with drain body Ø150 conforming to ÖNorm-EN1253
Basic body made of stainless steel 1.4571with removable PP odour trap Price group 231
vertical, with glued flange vertical, with clamp flange
Art. No. DN € / piece70.14.00 70 u.r.70.14.00-80 80 u.r.70.15.00 100 u.r.
Art. No. DN € / piece70.14.20 70 u.r.70.14.20-80 80 u.r.70.15.20 100 u.r.
horizontal, with glued flange horizontal, with clamp flange
Art. No. DN € / piece70.34.00 70 u.r.70.34.00-80 80 u.r.70.35.00 100 u.r.
Art. No. DN € / piece70.34.20 70 u.r.70.34.20-80 80 u.r.70.35.20 100 u.r.
Floo
r Dra
ins
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CHROMTECH® stainless steel floor drains DN 100with drain body Ø150 conforming to ÖNorm-EN1253
Extension with stainless steel grating and collar with weep holes
Price group 231
Art. No. Class Size € / piece71.71.41 L15 £ 200 u.r.71.71.42 M125 £ 200 u.r.71.71.41-3 L15 £ 300 u.r.71.71.42-3 M125 £ 300 u.r.
Extension with stain-less steel treadplate and collar with weep holes
Price group 231
Art. No. Class Size € / piece71.71.43 M125 £ 200 u.r.71.71.43-3 M125 £ 300 u.r.
Extension with slotted stainless steel grating and collar with weep holes
Price group 231
Art. No. Class Size € / piece71.71.44 K3 £ 200 u.r.71.71.44-1 L15 £ 200 u.r.
Plastic extension with slo-tted stainless steel grating and collar with weep holes
Price group 231
Art. No. Class Size € / piece71.71.45 K3 £ 200 u.r.71.71.45-1 L15 £ 200 u.r.
Extension with bar-type stainless steel gratings and collar with weep holes
Price group 231
Art. No. Class Size € / piece71.71.47 M125 £ 200 u.r.71.71.47-3 M125 £ 300 u.r.
Basic body made of stainless steel 1.4571with removable PP odour trap Price group 231
vertical, with glued flange vertical, with clamp flange
Art. No. DN € / piece71.31.00 100 175,-
Art. No. DN € / piece71.31.20 100 212,-
horizontal, with glued flange horizontal, with clamp flange
Art. No. DN € / piece71.61.00 100 278,-
Art. No. DN € / piece71.61.20 100 313,-
Floo
r Dra
ins
��0
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CHROMTECH® one-piece industrial drains, stainless steel DN 70/100/125/200made of stainless steel 1.4571, with large stainless steel mud bucket
verticalwithout flashinggrating class M 125
Price group 231
Art. No. DN Size Heightä € / piece74.44.02 70 £ 200 220 u.r.74.45.02 100 £ 200 220 u.r.74.45.12 100 £ 300 265 u.r.74.46.02 125 £ 300 265 u.r.74.47.02 150 £ 300 265 u.r.ä Height without connection pipe
verticalwithout flashingtreadplate class M 125
Price group 231
Art. No. DN Size Heightä € / piece74.44.03 70 £ 200 220 u.r.74.45.03 100 £ 200 220 u.r.74.45.13 100 £ 300 265 u.r.74.46.03 125 £ 300 265 u.r.74.47.03 150 £ 300 265 u.r.ä Height without connection pipe
verticalwithout flashingbar-type grating class M 125
Price group 231
Art. No. DN Size Heightä € / piece74.44.04 70 £ 200 220 u.r.74.45.04 100 £ 200 220 u.r.74.45.14 100 £ 300 265 u.r.74.46.04 125 £ 300 265 u.r.74.47.04 150 £ 300 265 u.r.ä Height without connection pipe
verticalwith flashinggrating class M 125
Price group 231
Art. No. DN Size Heightä € / piece73.44.02 70 £ 200 220 u.r.73.45.02 100 £ 200 220 u.r.73.45.12 100 £ 300 265 u.r.73.46.02 125 £ 300 265 u.r.73.47.02 150 £ 300 265 u.r.ä Height without connection pipe
verticalwith flashingtreadplate class M 125
Price group 231
Art. No. DN Size Heightä € / piece73.44.03 70 £ 200 220 u.r.73.45.03 100 £ 200 220 u.r.73.45.13 100 £ 300 265 u.r.73.46.03 125 £ 300 265 u.r.73.47.03 150 £ 300 265 u.r.ä Height without connection pipe
verticalwith flashingbar-type grating class M 125
Price group 231
Art. No. DN Size Heightä € / piece73.44.04 70 £ 200 220 u.r.73.45.04 100 £ 200 220 u.r.73.45.14 100 £ 300 265 u.r.73.46.04 125 £ 300 265 u.r.73.47.04 150 £ 300 265 u.r.ä Height without connection pipe
l Note: Covers also available in round design
Floo
r Dra
ins
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CHROMTECH® one-piece industrial drains, stainless steel DN 70/100/125/200made of stainless steel 1.4571, with large stainless steel mud bucket
horizontalwithout flashingGrating Class M 125
Price group 231
Art. No. DN Size Height € / piece74.64.02 70 £ 200 220 u.r.74.65.02 100 £ 200 220 u.r.74.65.12 100 £ 300 265 u.r.74.66.02 125 £ 300 265 u.r.74.67.02 150 £ 300 265 u.r.
horizontalwithout flashingtreadplate class M 125
Price group 231
Art. No. DN Size Height € / piece74.64.03 70 £ 200 220 u.r.74.65.03 100 £ 200 220 u.r.74.65.13 100 £ 300 265 u.r.74.66.03 125 £ 300 265 u.r.74.67.03 150 £ 300 265 u.r.
horizontalwithout flashingbar-type grating class M 125
Price group 231
Art. No. DN Size Height € / piece74.64.04 70 £ 200 220 u.r.74.65.04 100 £ 200 220 u.r.74.65.14 100 £ 300 265 u.r.74.66.04 125 £ 300 265 u.r.74.67.04 150 £ 300 265 u.r.
horizontalwith flashingGrating Class M 125
Price group 231
Art. No. DN Size Height € / piece73.64.02 70 £ 200 220 u.r.73.65.02 100 £ 200 220 u.r.73.65.12 100 £ 300 265 u.r.73.66.02 125 £ 300 265 u.r.73.67.02 150 £ 300 265 u.r.
horizontalwith flashingtreadplate class M 125
Price group 231
Art. No. DN Size Height € / piece73.64.03 70 £ 200 220 u.r.73.65.03 100 £ 200 220 u.r.73.65.13 100 £ 300 265 u.r.73.66.03 125 £ 300 265 u.r.73.67.03 150 £ 300 265 u.r.
horizontalwith flashingbar-type grating class M 125
Price group 231
Art. No. DN Size Height € / piece73.64.04 70 £ 200 220 u.r.73.65.04 100 £ 200 220 u.r.73.65.14 100 £ 300 265 u.r.73.66.04 125 £ 300 265 u.r.73.67.04 150 £ 300 265 u.r.
l Note: Covers also available in round design
Floo
r Dra
ins
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Add-on unit made of stainless steel Price group 231
Art. No. # for outlet body Typ € / piece70.71.00 - Ø 150 with glued flange u.r.70.71.20 u Ø 150 with clamp flange u.r.71.71.00 - Ø 230 with glued flange u.r.71.71.20 v Ø 230 with clamp flange u.r.
Add-on unit made of plastic Price group 231
Art. No. # for outlet body Typ € / piece70.71.00PVC u Ø 150 with glued flange u.r.70.71.20PVC v Ø 150 with clamp flange u.r.
Accessories Price group 231Art. No. Description for outlet body € / piece70.47.28 Mud basket Ø 150 u.r.70.71.30 Seal with backflow protection Ø 150 u.r.70.71.35 Grating screws Ø 150 u.r.71.47.28 Mud basket Ø 230 u.r.71.71.70 Mud basket Ø 230 u.r.71.71.30 Seal with backflow protection Ø 230 u.r.71.71.35 Grating screws Ø 230 u.r.l Side inlet , epoxy-coated upon request
Odour trap for fire protection F90
Price group 231
Art. No. for outlets € / piece
70.47.1170.12.00 - 70.13... DN 50, outlet body Ø 150
u.r.70.12.10 - 70.14... DN 70, outlet body Ø 15070.47.12 70.12.20 - 70.15... DN 100, outlet body Ø 150 u.r.71.47.11 71.30... - 71.40... DN 100, outlet body Ø 230 u.r.
u v
u v
CHROMTECH® - Accessoriesfor floor drains with outlet body Ø 150 und Ø 230
Stain
less s
teel
chan
nels
and
trays
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
PURALINE shower channelmade of stainless steel 1.4301
Slotted grating
Hole grating
Tile tray (tiles supplied by customer)
PURALINE shower channel is designed for on grade showers.A wide scope for your bahtroom design is given by the sleek appea-rance of 75 mm internal width and the availability of different design-gratings.
Please select from thefollowing design gratings:
PURALINE model 2 (2H) with glued flange, installa-tion height 89 mm (114 mm) with outlet capacity 0,65 l / sec (0,90 l / sec)
Pricegroup 233
Art. No. Channel Art. No. Design-grating Length € / set PURALINE2(H)-500 PURALINE-ä500 500 mm u.r.PURALINE2(H)-750 PURALINE-ä750 750 mm u.r.PURALINE2(H)-800 PURALINE-ä800 800 mm u.r.PURALINE2(H)-900 PURALINE-ä900 900 mm u.r.PURALINE2(H)-1000 PURALINE-ä1000 1000 mm u.r.PURALINE2(H)-1100 PURALINE-ä1100 1100 mm u.r.PURALINE2(H)-1200 PURALINE-ä1200 1200 mm u.r.PURALINE2(H)-1300 PURALINE-ä1300 1300 mm u.r.PURALINE2(H)-1400 PURALINE-ä1400 1400 mm u.r.PURALINE2(H)-1500 PURALINE-ä1500 1500 mm u.r.ä S for slotted grating, L for hole grating, F for tile tray
PURALINE model 3 (3H) with glued flange, installa-tion height 89 mm (114 mm) with outlet capacity 0,65 l / sec (0,90 l / sec) and loosly arranged waterproof fleece
Pricegroup 233
Art. No. Channel Art. No. Design-grating Length € / set PURALINE3(H)-500 PURALINE-ä500 500 mm u.r.PURALINE3(H)-750 PURALINE-ä750 750 mm u.r.PURALINE3(H)-800 PURALINE-ä800 800 mm u.r.PURALINE3(H)-900 PURALINE-ä900 900 mm u.r.PURALINE3(H)-1000 PURALINE-ä1000 1000 mm u.r.PURALINE3(H)-1100 PURALINE-ä1100 1100 mm u.r.PURALINE3(H)-1200 PURALINE-ä1200 1200 mm u.r.PURALINE3(H)-1300 PURALINE-ä1300 1300 mm u.r.PURALINE3(H)-1400 PURALINE-ä1400 1400 mm u.r.PURALINE3(H)-1500 PURALINE-ä1500 1500 mm u.r.ä S for slotted grating, L for hole grating, F for tile tray
PURALINE mounting set Pricegroup 233
Art. No. € / piece PURALINE-SET u.r.
Stain
less s
teel
chan
nels
and
trays
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CHROMTECH® - stainless steel channels and trays
General features:
l stainless steel 1.4301 or 1.4571l welded constructionl optional without/0,5%/1% pitchl adjustable base for continuous heightl drained by an integrated socket, vertically incorporated into the
bottom of the channel fitting for CHROMTECH® floor drainsl optional with hollow space filling, wall edging and tile connector
bracket
Channels exceeding 6.000 mm length are delievered in parts and mounted with screwed flanged connectors
CHROMTECH® box gutter E with 50 mm universal flange Pricegroup 232
l circumferential design edge with 8 mm widel channel width up to 200 mml gratings see page 157l connection to tiled floor / thin mortar bed /
synthetic resin flooring
CHROMTECH® box gutter D Pricegroup 232
l circumferential design edge with 8 mm widel channel width up to 200 mml gratings see page 157l connection to tiled floor / screed
Stain
less s
teel
chan
nels
and
trays
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CHROMTECH® - stainless steel channels and trays
CHROMTECH® box gutter A with 50 mm universal flange Pricegroup 232
l circumferential design edge 25 mm widel channel width from 200 mml gratings see page 157l connection to tiled floor / thin mortar bed /
synthetic resin flooring
CHROMTECH® tray A with 50 mm universal flange Pricegroup 232
l stainless steel 1.4301l circumferential design edge 25 mm widel connection to tiled floor / thin mortar bed /
synthetic resin flooringl grating with anti-slip finish,
mesh size 30 x 30 mm class L 15
Art. No. Dimensions L x B h H max X-measurement Ø Da € / piece
26.12.36 300 x 300 50 70 16 185 u.r.26.12.46 400 x 400 50 70 16 185 u.r.26.12.56 500 x 500 50 70 16 185 u.r.26.12.66 600 x 600 50 70 16 185 u.r.26.12.86 800 x 800 50 70 16 185 u.r.26.12.16 1000 x 1000 50 70 16 185 u.r.l different gratings upon request
CHROMTECH® - box gutters and special trays are quoted and produced upon request
Stain
less s
teel
chan
nels
and
trays
��6
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CHROMTECH® - stainless steel slit gutter
General features:
l stainless steel 1.4301 or 1.4571l welded constructionl optional without/0,5%/1% pitchl adjustable base for continuous heightl drained by a welded on socket fitting for CHROMTECH® floor
drainsl optional with tile connector bracket
Channels exceeding 6.000 mm length are delievered in parts and mounted with screwed flanged connectors
CHROMTECH® slit gutter K with 50 mm universal flange Pricegroup 232
l design edge 22,5 mml slit width 20 mml channel width from 200 mml gratings see page 157l connection to tiled floor / thin mortar bed /
synthetic resin flooring
CHROMTECH® slit gutter H Pricegroup 232
l design edge 22,5 mml slit width 20 mml gratings see page 157l connection to tiled floor / screed
Stain
less s
teel
chan
nels
and
trays
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
CHROMTECH® - stainless steel slit gutter
CHROMTECH® slit gutter SK8 with 35 mm glued flange Pricegroup 232
l design edge 15 mml slit width 8 mm (barefoot secure)l gratings see page 157l connection to tiled floor / thin mortar bed
CHROMTECH® gratings for channels and trays Pricegroup 232
Grating class L 15 Grating class M 125
Bar-type grating class M 125 Treadplate class M 125
PVC roll-up grating class K 3 Slotted grating or Hole grating (no img.) class K 3 or L 15
CHROMTECH® - slit gutters are quoted and produced upon request
anti-slip finishmesh size: 30 x 30 mm, 30 x 10 mm, 23 x 23 mm - further mesh sizes upon request
anti-slip finishmesh size: 30 x 30 mm, 30 x 10 mm, 23 x 23 mm - further mesh sizes upon request
barefoot secure finishstandard colours: white, beige, greyother colours upon request
barefoot secure finish
l Please ask for your individual grating design!
Base
men
t dra
ins a
nd
heat
ing
oil s
tops
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
HL Perfekt plastic drainswith frost-proof odour trap
HL606Perfekt drain DN110 vertical with plastic frame 244 x 244 mm, cast inlet grating 226 x 226 mm, grit catcher und frost and dry-out-proof odour trap
Price group 250
Art. No. DN Frame Grate Class € / pieceHL606L 110 Plastic Plastic 15 kN u.r.HL606 110 Plastic Cast iron 15 kN u.r.HL606.1 110 Cast iron Cast iron 125 kN u.r.HL606.1/160 160 Cast iron Cast iron 125 kN u.r.HL606-160 160 Plastic Cast iron 15 kN u.r.
HL605Perfekt drain DN110 horizontal with plastic frame 244 x 244 mm, cast inlet grating 226 x 226 mm, grit catcher und frost and dry-out-proof odour trap
Price group 250
Art. No. DN Frame Grate Class € / pieceHL605L 110 Plastic Plastic 15 kN u.r.HL605 110 Plastic Cast iron 15 kN u.r.HL605.1 110 Cast iron Cast iron 125 kN u.r.
HL616LPerfekt drain DN110 vertical with sealing flange, plastic frame (can be trimmed to required size) 42 - 130 mm / 240 x 240 mm and screw-on grating 226 x 226 mm, grit catcher und frost and dry-out-proof odour trapPrice group 250Art. No. DN Frame Grate Class € / pieceHL616L 110 Plastic Plastic 15 kN u.r.
HL616HLPerfekt drain DN110 vertical with factory welded bitumen collar, d 500 mm as perfect connection to bituminous sealing, plastic frame (can be trimmed to required size) 42 - 130 mm / 240 x 240 mm and screw-on grating 226 x 226 mm, grit catcher und frost and dry-out-proof odour trapPrice group 250
Art. No. DN Frame Grate Class € / pieceHL616HL 110 Plastic Plastic 15 kN u.r.
HL615LPerfekt drain DN110 horizontal with sealing flange, plastic frame (can be trimmed to required size) 42 - 130 mm / 240 x 240 mm and screw-on grating 226 x 226 mm, grit catcher und frost and dry-out-proof odour trapPrice group 250Art. No. DN Frame Grate Class € / pieceHL615L 110 Plastic Plastic 15 kN u.r.
HL615HLPerfekt drain DN110 horizontal with factory welded bitumen collar, d 500 mm as perfect connection to bituminous sealing, plastic frame (can be trimmed to required size) 42 - 130 mm / 240 x 240 mm and screw-on grating 226 x 226 mm, grit catcher und frost and dry-out-proof odour trap
Price group 250
Art. No. DN Frame Grate Class € / pieceHL615HL 110 Plastic Plastic 15 kN u.r.
Notes:1. vertical drains also available in DN 1602. all drains shown can also be supplied with water odour trap instead of frost-proof odour trap3. all Perfekt drains can be supplied with either plastic or cast iron gratings4. For class B 125 kN design, combination of cast iron frame/cast iron grating is mandatory
Base
men
t dra
ins a
nd
heat
ing
oil s
tops
���
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Basement drains, heating oil stops
Basement drain made of PPDN 100, lateral outlet 2,5°, class K 3 kN, with 2 inlets DN 50, 1 inlet DN 70, with removable odour trap and mud bucket
Price group 250
Art. No. Description DN € / piece
329111 Plastic slotted grating 200 x 200 mm 100 u.r.
329121 Stainless steel slotted grating 200 x 200 mm 100 u.r.
Basement drain made of ABSDN 100, lateral outlet 2,5°, class K 3 kN, with removable dual anti-flooding valve and manually lockable emergency stop and mud bucketPrice group 250
Art. No. Description DN € / piece
327301 Plastic slotted grating 150 x 190 mm 100 u.r.
Basement drain made of PPDN 100, lateral outlet 2,5°, class K 3 kN, with 2 inlets DN 50, 1 inlet DN 70, with removable dual anti-flooding valve and manually lockable emergency stopPrice group 250
Art. No. Description DN € / piece
327611 Plastic slotted grating 200 x 200 mm 100 u.r.
327621 Stainless steel slotted grating 200 x 200 mm 100 u.r.
Cast iron Basement drainwith anti-flooding valve, lockable with service key
Price group 140
Art. No. Description DN Weight (kg)
€ / piece
140-6020-00-00 grating 150 x 200 mm 100 11,5 u.r.
Accessories:140-6040-00-00 service key - u.r
Univa heating oil stopmade of plastic, with odour trap, with/without anti-flooding valve
Price group 250
Art. No. Description DN Weight (kg) € / piece
351101 without anti-flooding valve 100 3,9 u.r.
352101 with anti-flooding valve 100 4,3 u.r.l Special extension upon request
Cast iron heating oil stopwith odour trap, without anti-flooding valve
Price group 140
Art. No. Description DN Weight (kg) € / piece
140-6760-00-00 without anti-flooding valve 100 23,0 u.r.
Cast iron heating oil stopwith odour trap, with anti-flooding valve
Price group 140
Art. No. Description DN Weight (kg) € / piece
140-6763-00-00 without anti-flooding valve 100 44,0 u.r.
Rain
wate
r dra
ins
�60
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Rainwater drains
Cast iron rainwater drainswith bucket, vertical drainage, without odour trap
Price group 70
Art. No. DN DN1 Weight (kg) € / piece
1003A 100 125 8,5 u.r.1003B 125 150 10,0 u.r.1003C 150 175 11,5 u.r.Spare parts:E1003A-C-N PVC bucket, loose u.r.
Cast iron rainwater drainswith dirt trap, vertical draina-ge, without odour trap
Price group 70
Art. No. DN DN1 Weight (kg) € / piece
1003AN 100 125 8,5 u.r.Spare parts:E1003A-N PVC dirt trap u.r.1003AN-MRS Bushing reduction u.r.
Rainwater drains made of prefabricated concrete partswith PE bucket, cast iron lid, side outlet with bushing
Price group 140
Art. No. Description DN DN1 Weight (kg) € / piece
140-5201-10-00 without odour trap 100 100 60,0 u.r.140-5203-10-00 without odour trap 150 150 65,0 u.r.
Rainwater drains made of prefabricated concrete partswith PE bucket, cast iron lid, side outlet with bushingPrice group 140
Art. No. Description DN DN1 Weight (kg) € / piece
140-5211-10-00 with odour trap 100 100 73,0 u.r.140-5213-10-00 with odour trap 150 150 91,0 u.r.
Accessories for prefabricated concrete rainwater drainPrice group 140
Art. No. Description H (mm)
Weight (kg) € / piece
E9201-13 bucket, loose - - u.r.140-5215-00-00 Concrete compensating unit 300 19 u.r.140-5216-00-00 Concrete compensating unit 400 24 u.r.140-5216-10-00 Concrete compensating unit 500 29 u.r.
Plastic rainwater drainagewith leaf trap and odour trap, pin-connectedadjustable from 0° to 90°
Price group 250
Art. No. DN Weight(kg) € / piece
HL600 100 1,6 u.r.HL600/2 125 1,8 u.r.
Plastic odour traps
Price group 250
Art. No. # Description DN € / pieceHL603-100 u Pipe odour trap
for downpipes, for installation in vertical pipes
100 u.r.HL603-150 v 150 u.r.
u v
Plastic rainwater drainblack, with leaf trap and odour trap
Price group 250
Art. No. Description DN DN1 Weight (kg) € / piece
PWN-RSE DN 100/110 100 80-125 1 u.r.
NEW!
Rain
wate
r dra
ins
�6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Modular system Plastic yard gullies/stormwater gullies
Supporting frame, class 15 kN
Art. No. € / piece327180 u.r.
Slotted grating, class L 15 kN
Art. No. € / piece327173 u.r.
Stormwater gully cover
Art. No. € / piece367750 u.r.
Stormwater gully cover
Art. No. € / piece367700 u.r.
Stormwater gully cover
Art. No. € / piece367775 u.r.
Cast iron supporting frameclass M 125 kNArt. No. € / piece327181 u.r.
Cast iron slotted grating,class M 125 kNArt. No. € / piece327174 u.r.
Extension piece, with supp. frame
Art. No. € / piece348985 u.r.
Bell-type odour trap
Art. No. € / piece327171 u.r.
Drain body laterally
Art. No. € / piece367000 u.r.
Plastic extension piece
Art. No. € / piece367400 u.r.
Adaptor
Art. No. € / piece367500 u.r.
Adaptor
Art. No. € / piece367600 u.r.
Valve insert for leakproof-ness test
Art. No. € / piece348984 u.r.
Bell-type odour trap
Art. No. € / piece327170 u.r.
Fireproof insert with odour trap
Art. No. € / piece348200 u.r.
Bell-type stainless steel odour trap
Art. No. € / piece327182 u.r.
Mud bucket
Art. No. € / piece367300 u.r.
Backflow ball
Art. No. € / piece348980 u.r.
Drain body vertical
Art. No. € / piece367040 u.r.
Wall bracket
Art. No. € / piece367800 u.r.
Lip-type seal
Art. No. € / piece327140 u.r.
Lip-type seal
Art. No. € / piece327141 u.r.
Lifting device
Art. No. € / piece3850144 u.r.
Price group 250 für all products shown on this page
�6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Term
s & C
ondi
tions
�6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Table of contentsTerms & Conditions
Terms & Conditions 164
Gene
rals
�6�
All information subject to change. Errors and omissions excepted. All rights reserved.
PURATOR Central and Eastern EuropeTel.: +43 (0)5 05 13-0, Fax: +43 (0)5 05 13-300, Mail: [email protected], Web: www.purator.com
Terms and Conditions of Sale, Delivery and Payment 2007
1. GENERAL1.1 These sales, delivery and payment conditions are valid for all sales and other legal transactions with our customers insofar as they are not consumers in the sense of the Austrian Consumer Protection Act (KSchG). In the event that one of our customers does fulfill the characteristics of a consumer in the sense of Austrian Consumer Protect Act those conditions will be modified by the mandatory articles of the currently valid version of the Austrian Consumer Protection Act. Those conditions will also be valid even if contrary conditions of the customer remain unopposed. Such conditions will only be deemed to have been recognized by us if they have been accepted by us in writing prior to the provision of the order confirmation.1.2 The prices we offer are generally non-binding and only become binding after acceptance of an order. A commitment of any other kind must be specially agreed to.Orders and/or the acceptance of offers generally must take place in writing.Products order via electronic means will be confirmed immediately after the receipt of the customer’s order. This receipt confirmation does not present any kind of binding acceptance of the order. The receipt confir-mation only presents a declaration of acceptance if we expressly declare this. Declarations to our customers are deemed to have been received if they have been given in the event of orders by the customers or if they have been sent to different addresses in writing afterwards. As per these general terms and conditions of trade, declarations that must be provided in writing –insofar as nothing to the contrary is declared- may also be provided via fax or email.1.3 If our order confirmation is not objected to in writing within one week, it is valid as contractual content.1.4 Prices, if nothing to the contrary has been agreed to, are ex factory plus value-added tax. An increase to the price basis (raw material, collective agreement, energy, other costs) between offer, order and delivery allows us to make a corresponding price adjustment. The conclusion of the contract takes place under the re-servation that service will not be provided or provided only in part in the event of incorrect or improper delivery to us of supplies and raw materials. The customer will be informed immediately in the event of unavailability or only partial availability of service. Any service already provided will be refunded immediately.1.5 Subsequent changes or supplement require our written confirmation in order to be valid. Additional oral agreements are also unenforceable.
2. DELIVERY2.1 Our business address is deemed to be the place of fulfillment agreed to. Any another place of fulfillment requires written agreement. The products will always be delivered at the cost and risk of the customer insofar as nothing to the contrary is agreed to. Prices in delivery agreements do not include unloading and transportation.2.2 Agreed upon deliveries assumes that the access road can be drive on by a heavy transportation vehicle.2.3 The products are deemed to have been delivered even if they are not immediately requested after notifica-tion of their readiness to ship; in these cases we are entitled to store the products at the cost of our customers.2.4 Force Majeure and other unforeseeable events or events not caused by us such as labor disputes, governmental measures, traffic disturbances, interruptions to the energy supply, et cetera as well as traffic accidents not caused by us or our suppliers free us from the obligation of delivery for their duration, even if they have happened to our suppliers or their suppliers, but only insofar, in every event, as we can prove these events as the cause of the disturbance of service to the customer. If delivery is made impossible by these events named, our delivery obligation expires under the same conditions.2.5 The products will be packed and shipped as is customary. The packaging will be billed at our own whole-sale prices. Packaging material will only be taken back or compensated for insofar as this has been agreed to in writing. Loading devices (e.g. palettes, attachment frames, wire boxes, loading lumber, et cetera) will be exchanged for cash against delivery or charged to the buyer wherein we will credit these free of all charges if they are returned within four weeks. The precondition for exchange and return is the proper condition of the loading device.2.6 The products will only be insured against damage, loss or break during transport upon the written request of the customer and at their expense to their account. Externally recognizable transportation damages must be immediately registered after receipt of the goods to the exclusion of other guarantees and the nature and scope of the damage must be immediately provided in writing.2.7 In the event that the products ordered are sent in the form of data via the internet and/or acquired by the customer via a download, the risk of destroying or changing the data transfers to the customer upon accessing the network interface.
3. NOTIFICATION OF DEFECTS / GUARANTEE3.1 We guarantee that the products are in order and posses the standard characteristics; liability for special characteristics is only assumed if this has been confirmed in writing.3.2 For products that have been designated to be of lower quality, such as “second choice”, the guarantee is correspondingly limited to those characteristics which can be expected given the special characterization of the product. 3.3 No guarantee can be given for production and material based variations to color nuances.3.4 Delivered products must be inspected by the customer immediately; defects determined must be immedi-ately registered under a special exclusion of the guarantee prior to processing or installation.3.5 Returned products will only be accepted by us after prior written agreement and placed in our warehouse free of charge if they are in flawless condition. Our personnel are only allowed to accept products with return certificate created by the company. We are entitled to bill 20% of the amount of the order, as well as any shipping performed, as handling charges – but at least 50.00 EUR per occurrence. The return and exchange of custom-made products is generally not possible.3.6 Our guarantee only applies to defects occurring under compliance with the intended installation, operation and maintenance instructions during normal use. This especially does not apply to defects occurring due to poor assembly by the customer or their agents, poor maintenance, poor repairs or those not conducted with our approval, alterations or normal wear and tear.3.7 We will then honor our guarantee for defective products via our choice of improvement or exchange.3.8 If an improvement is not possible or feasible, the customer generally requests their choice of a price reduction or, insofar as this does not merely concern a minor defect, cancellation of the contract. 3.9 The customer bears the entire burden of proof for all claim requirements, particularly those for the defect itself, the time of determination of the defect and the timeliness of the notification of the defect.3.10 The period of guarantee is six months following the delivery of the product.3.11 The right of recourse as per § 933 b of the Austrian Civil Code (ABGB) in the event that our commercial customer must provide a guarantee to a customer is excluded.3.12 We do not provide any guarantees to our customers in the legal sense. Manufacturer’s guarantees are unaffected by this.
4. PRODUCT LIABILITY AND DAMAGE COMPENSATION LIABILITY4.1 We are liable for damages caused by us in the context of product liability as well as those we are culpable for causing in the context of the valid legal conditions; under consideration of the following fixed conditions:
4.2 We are not liable for the accuracy of information regarding maintenance, use or operation insofar as this is included in prospectuses, technical descriptions or other instructions; these are the responsibility of the manufacturer and/or importer. We are also not obligated to provide any additional information, particularly regarding storage, maintenance, installation or other handling.4.3 In the event of material or pecuniary damage, we are only liable in the event of deliberate acts or gross negligence by persons accountable to us. The liability is limited to the actual value of the order. Liability for additional damages is expressly prohibited. There is no claim to lost profits in any event.4.4 Our liability is limited to deliberate misconduct or gross negligence outside of the area of application of the Austrian Product Liability Law. Liability for slight negligence, compensation for consequential and pecuniary damages, unmet savings, loss of interest and damages resulting from the claims of third parties against customers is prohibited.4.5 The previously listed limitations of liability are not valid for damages to the body or health attributable to us or the loss of life of the customer.4.6 We are only liable for our own content on our website. Insofar as we enable access to other websites via links, we are not responsible for the external content contained there. The external content is not ours. Insofar as we learn of unlawful content on external websites, we will immediately block access to these pages.4.7 Claims against us for damage compensation, regardless of what kind, expire –insofar as shorter expiration or preclusive periods are not legally valid – six months from the time that the customer learned of the damage and the person damage or other event used to make a claim.
5. PAYMENT5.1 Our bills are due for immediately insofar as no other arrangement has been made. The use of approved discounts requires that all prior bills –with the exception of those justifiably objected by our customers – have been paid. Incoming payments will be assigned to the oldest respective bills.5.2 A payment is deemed to have been paid from the day on which we have access to it.5.3 Our employees are only entitled to accept payments with an express, written, power of collection.5.4 Checks and bills of exchange will only be accepted as payment with express prior agreement; exchange taxes, discount, objection and collection expenses will be borne by the customer. We make no guarantee for timely billing and objections.5.5 Offsetting with counterclaims is only permissible insofar as these are recognized by us or have been determined to be legally valid.5.6 In the event of default in payment, we are entitled, regardless of additional claims, to assess default interest in the amount of 8% above the basic rate.5.7 All costs associated with dunning, collection and attorneys incurred in the process of the recovery of debt will be borne entirely by the culpable party.5.8 In the event of default on the part of the customer we are entitled to demand immediate payment of outstanding debts; we are also entitled to this right if we learn of unfavorable circumstances regarding the customer’s ability to make payment or their economic circumstances after the conclusion of the contract.5.9 If the customer does not meet our request for payment despite the establishment of an eight-day grace period, we are entitled, regardless of our other rights to take back the products in our possession without simultaneously withdrawing from the contract or to wholly or partial withdraw from the contract to protect our rights, particularly those for damage compensation from non-fulfillment.5.10 The billed prices agreed upon are valid with the requirement that the agreed upon payment conditions are complied with. If these payments are not made on time, we are entitled to subsequently bill the difference between any discount given and the list prices.5.11 In the event of atypical and unforeseeable price increases in raw materials and/or energy costs underly-ing our products, we have the right to an extraordinary price adjustment in the sense of correction to the extent of the increase in price for the raw materials for prices already given by us for products subject to damage compensation reduction. In this event, the buyer is entitled to withdraw from the contract using registered mail within a period of 14 days after the announcement of the new sales price. This applies to the agreed upon elimination of possible fulfillment, non-fulfillment and/or breaches of faith.
6. RETENTION OF PROPRIETARY RIGHTS6.1 Delivered products remain our property until complete payment of all obligations on the part of the custo-mer resulting from the sales contract. The customer is obligated to make the retention of proprietary rights by us on the delivered products known to all. The customer is obligated to treat the products with care during the retention of proprietary rights. Insofar as maintenance and inspection work is necessary, the customer must conduct these regularly at their own expense.6.2 The customer is entitled to sell products we retain proprietary right over in the course of their daily busi-ness. In this case, the customer will cede all possible payments resulting from the sale of our products to third parties to us as payment, which we will accept. The customer is obligated to inform us about the successful cession. After cession, the company is entitled to collect the payment in our name. We reserve the right to coll-ect the payment ourselves as soon as the company has not properly fulfilled their payment obligations and is in default of payment. The customer is obligated to make a corresponding record in their books and invoices. The customer is prohibited from using such products of securities or pawning them as well as any other uses not corresponding to daily business operations. If products that are still our property are pawned or otherwise seized by third parties, the customer must inform us immediately; costs accruing from the enforcement of our rights will be compensated by the customer.6.3 Manipulation or processing of products that are our property also does not eliminate our reservation of the property; in this event, it is deemed as agreed to that we are entitled to an aliquot share of the joint ownership of the items created by manipulation or processing.6.4 In the event of elimination of the law enabling the retention of proprietary right, a request for the sales price will take its place. These will then be due to us.
7. PLACE OF FULFILLMENT7.1 The application of Austrian law has been agreed to. The application of The United Nations Convention on the International Sale of Goods has been mutually excluded.7.2 The place of jurisdiction is the location of the seller unless the customer is prosecuted elsewhere at the seller’s choice. The place of fulfillment is the location of the seller unless the delivery has taken place somewhere as per agreement.
8. CLOSING REMARKS:Should individual conditions of the sales, delivery and payment be wholly or partially unenforceable, the other conditions will remain valid.
Wallner & Neubert Gesellschaft m.b.H.HG Wien,FN 152084d,UID ATU41961908, ARA LN Nr. [email protected], www.pwn.at
Head Quater WienSchönbrunner Straße 13A-1052 WienTel. +43 (0)1/588 13-0Fax +43 (0)1/588 [email protected]
Logistic Center MödlingIm Felberbrunn 2A-2340 MödlingTel. +43 (0)1/588 13-0Fax +43 (0)1/588 13-500
Branch Office GrazReininghausstraße 25A-8020 GrazTel. +43 (0)316/57 42 58-0Fax +43 (0)316/57 42 [email protected]
Wallner & Neubert Gesellschaft m.b.H.
Branch Office RegauPreising 84A-4844 RegauTel. +43 (0)7674/622 25-0Fax +43 (0)7674/622 [email protected]
Branch Office TirolSchlöglstraße 59A-6060 Hall in TirolTel. +43 (0)5223-54320Fax +43 (0)[email protected]
www.pwn.atw
ww
.pur
ator
.com
BiH Generalno zastupništvo - Remak d.o.o.Nedima Filipovića 27dBiH-71000 SarajevoTel.:+387 33 71 68 41Fax:+387 33 71 68 [email protected], www.purator.com
BG фирма БЕРКСул.Любен Каравелов 112 BG-8000 Бургас Tel.:+359 56 815 775Fax:+359 56 815 775www.purator.com, [email protected]
CZ Purator-Techno Tip CZ, spol. s r.o.Šumavská 15 CZ-602 00 Brno Tel.:+420 5 41 59 25 93Fax:+420 5 41 59 25 93www.purator.cz, [email protected]
H Purator Hungaria Kft.Vöröskereszt utca 8-10H-1222 BudapestTel.:+36 1 464 72 00Fax:+36 1 464 72 01www.purator.hu, [email protected]
HR Generalno zastupstvo - PRONEKO d.o.o.Savska 42HR - 10000 ZagrebTel.: + 385 1 61 76 072Fax: + 385 1 61 77 693www.proneko.hr
PL Purator Polska Ekotechnika Sp. z o.o.ul. Poloneza 93PL-02-826 WarszawaTel.:+48 22 543 89 89Fax:+48 22 543 80 15www.purator.pl, [email protected]
RO Purator Ecotechnic s.r.l.Str. Mihai Bravu, no. 192, ap. 6, sector 3RO-021344 BucharestTel.:+40 21 323 84 16Fax:+40 21 323 84 16www.purator.ro, [email protected]
SRB Purator Ekotehnika d.o.o.Draže Pavlovića 31SCG-11120 BeogradTel.: +381 11 276 78 90Fax: +381 11 276 41 42www.purator.com
SK Purator-Techno Tip spol. s r.o.Puchovská 16SK-83505 BratislaváTel.:+421 2 49 20 86 40Fax:+421 2 49 20 86 41www.purator.sk
SLO Purator Ekotehnik d.o.o.Gmajna 16SLO-1236 TrzinTel.:+386 1 564 45 95Fax:+386 1 562 13 76www.purator.com