Download - Ch2 Conduction

Transcript
Page 1: Ch2  Conduction

Heat Conduction Equation

BMCG 2123Faculty of Manufacturing Engineering,

UTeMTaufik

Week 204/11/23 BMCG 2123 Heat Transfer 1

Page 2: Ch2  Conduction

04/11/23 BMCG 2123 Heat Transfer 2

Learning Objectives At the end of this chapter, students

should be able to: Explain multidimensionality and time dependence of

heat transfer. Obtain the differential equation of heat conduction

in various coordinate systems. Solve one-dimensional heat conduction problems

and obtain the temperature distributions within a medium and the heat flux,

Analyze one-dimensional heat conduction in solids that involve heat generation.

Page 3: Ch2  Conduction

Introduction

• Although heat transfer and temperature are closely related, they are of a different nature.

• Temperature has only magnitudeit is a scalar quantity.

• Heat transfer has direction as well as magnitude it is a vector quantity.

• We work with a coordinate system and indicate direction with plus or minus signs.

Page 4: Ch2  Conduction

Introduction ─ Continue• The driving force for any form of heat transfer is the

temperature difference.• The larger the temperature difference, the larger the

rate of heat transfer.• Three prime coordinate systems:– rectangular (T(x, y, z, t)) ,– cylindrical (T(r, , z, t)),– spherical (T(r, , , t)).

Page 5: Ch2  Conduction

Classification of conduction heat transfer problems:• steady versus transient heat transfer,• multidimensional heat transfer,• heat generation.

Introduction ─ Continue

Page 6: Ch2  Conduction

Steady versus Transient Heat Transfer

• Steady implies no change with time at any point within the medium

• Transient implies variation with time or time dependence

Page 7: Ch2  Conduction

Multidimensional Heat Transfer

• Heat transfer problems are also classified as being:– one-dimensional,– two dimensional,– three-dimensional.

• In the most general case, heat transfer through a medium is three-dimensional. However, some problems can be classified as two- or one-dimensional depending on the relative magnitudes of heat transfer rates in different directions and the level of accuracy desired.

Page 8: Ch2  Conduction

• The rate of heat conduction through a medium in a specified direction (say, in the x-direction) is expressed by Fourier’s law of heat conduction for one-dimensional heat conduction as:

• Heat is conducted in the direction of decreasing temperature, and thus the temperature gradient is negative when heat is conducted in the positive x-direction.

(W)cond

dTQ kA

dx (2-1)

Page 9: Ch2  Conduction

General Relation for Fourier’s Law of Heat Conduction

• The heat flux vector at a point P on the surface of the figure must be perpendicular to the surface, and it must point in the direction of decreasing temperature

• If n is the normal of the isothermal surface at point P, the rate of heat conduction at that point can be expressed by Fourier’s law as

(W)n

dTQ kA

dn (2-2)

Page 10: Ch2  Conduction

General Relation for Fourier’s Law of Heat Conduction-Continue

• In rectangular coordinates, the heat conduction vector can be expressed in terms of its components as

• which can be determined from Fourier’s law as

n x y zQ Q i Q j Q k

x x

y y

z z

TQ kA

xT

Q kAy

TQ kA

z

(2-3)

(2-4)

Page 11: Ch2  Conduction

Heat Generation• Examples:– electrical energy being converted to heat at a rate of I2R,– fuel elements of nuclear reactors,– exothermic chemical reactions.

• Heat generation is a volumetric phenomenon.• The rate of heat generation units : W/m3 or Btu/h · ft3.• The rate of heat generation in a medium may vary with

time as well as position within the medium. • The total rate of heat generation in a medium of

volume V can be determined from

(W)gen gen

V

E e dV (2-5)

Page 12: Ch2  Conduction

Exercise 1• The resistance wire of a 1200-W hair dryer is 80 cm

long and has diameter of D = 0.3 cm. Determine: a) the rate of heat generation in the wire per unit

volume, in W/cm3, andb) The heat flux on the outer surface of the wire as

result of this heat generation.

04/11/23 BMCG 2123 Heat Transfer 12

Page 13: Ch2  Conduction

Solution 1

a) The rate of heat generation:

b) The heat flux on the outer surface:

04/11/23 BMCG 2123 Heat Transfer 13

3

22 W/cm212

804/)3.0(

1200

4/

cmcm

W

LD

E

V

Ee

gen

wire

gengen

2/ 9.15)80)(3.(

W1200cmW

cmcmoDL

E

A

EQ gen

wire

gens

Page 14: Ch2  Conduction

One-Dimensional Heat Conduction Equation - Plane Wall

xQ

Rate of heat

conduction

at x

Rate of heat

conduction

at x+x

Rate of heat

generation inside the element

Rate of change of the energy content of

the element

- + =

,gen elementE x xQ elementE

t

(2-6)

Page 15: Ch2  Conduction

• The change in the energy content and the rate of heat generation can be expressed as

• Substituting into Eq. 2–6, we get

,

element t t t t t t t t t

gen element gen element gen

E E E mc T T cA x T T

E e V e A x

,element

x x x gen element

EQ Q E

t

(2-6)

(2-7)

(2-8)

x x xQ Q (2-9)gene A x t t tT T

cA xt

1gen

T TkA e c

A x x t

(2-11)

• Dividing by Ax, taking the limit as x 0 and t 0, and from Fourier’s law:

Page 16: Ch2  Conduction

The area A is constant for a plane wall the one dimensional transient heat conduction equation in a plane wall is

gen

T Tk e c

x x t

Variable conductivity:

Constant conductivity:2

2

1 ; geneT T k

x k t c

1) Steady-state:

2) Transient, no heat generation:

3) Steady-state, no heat generation:

2

20gened T

dx k

2

2

1T T

x t

2

20

d T

dx

The one-dimensional conduction equation may be reduces to the following forms under special conditions

(2-13)

(2-14)

(2-15)

(2-16)

(2-17)

Page 17: Ch2  Conduction

One-Dimensional Heat Conduction Equation - Long

Cylinder

rQ

Rate of heat

conductionat r

Rate of heat

conduction

at r+r

Rate of heat

generation inside the element

Rate of change of the energy content of

the element

- + =

,gen elementE elementE

t

r rQ

(2-18)

Page 18: Ch2  Conduction

• The change in the energy content and the rate of heat generation can be expressed as

• Substituting into Eq. 2–18, we get

,

element t t t t t t t t t

gen element gen element gen

E E E mc T T cA r T T

E e V e A r

,element

r r r gen element

EQ Q E

t

(2-18)

(2-19)(2-20)

r r rQ Q (2-21)gene A r t t tT T

cA rt

1gen

T TkA e c

A r r t

(2-23)

• Dividing by Ar, taking the limit as r 0 and t 0, and from Fourier’s law:

Page 19: Ch2  Conduction

Noting that the area varies with the independent variable r according to A=2rL, the one dimensional transient heat conduction equation in a plane wall becomes1

gen

T Trk e c

r r r t

10gened dT

rr dr dr k

The one-dimensional conduction equation may be reduces to the following forms under special conditions

1 1geneT Tr

r r r k t

1 1T Tr

r r r t

0d dT

rdr dr

Variable conductivity:

Constant conductivity:

1) Steady-state:

2) Transient, no heat generation:

3) Steady-state, no heat generation:

(2-25)

(2-26)

(2-27)

(2-28)

(2-29)

Page 20: Ch2  Conduction

One-Dimensional Heat Conduction Equation - Sphere

22

1gen

T Tr k e c

r r r t

22

1 1geneT Tr

r r r k t

Variable conductivity:

Constant conductivity:

(2-30)

(2-31)

Page 21: Ch2  Conduction

General Heat Conduction Equation

x y zQ Q Q

Rate of heat

conduction

at x, y, and z

Rate of heat

conduction

at x+x, y+y, and

z+z

Rate of heat

generationinside theelement

Rate of changeof the energy

content of the

element

- + =

x x y y z zQ Q Q ,gen elementE elementE

t

(2-36)

Page 22: Ch2  Conduction

Repeating the mathematical approach used for the one-dimensional heat conduction the three-dimensional heat conduction equation is determined to be

2 2 2

2 2 2

1geneT T T T

x y z k t

2 2 2

2 2 20geneT T T

x y z k

2 2 2

2 2 2

1T T T T

x y z t

2 2 2

2 2 20

T T T

x y z

Two-dimensional

Three-dimensional

1) Steady-state:

2) Transient, no heat generation:

3) Steady-state, no heat generation:

Constant conductivity: (2-39)

(2-40)

(2-41)

(2-42)

Page 23: Ch2  Conduction

Exercise 2• A 2-kW resistance heater with thermal conductivity

k = 15 W/m.K, diameter D = 0.4 cm, and length L = 50 cm is used to boil water by immersing it in water. Assuming the variation of thermal conductivity of the wire with temperature to be negligible, obtain the differential equation that describes the variation of the temperature in the wire during steady state operation.

04/11/23 BMCG 2123 Heat Transfer 23

Page 24: Ch2  Conduction

Analysis

The resistance wire of a water heater is considered to be a very long cylinder since its length is more than 100 times its diameter. Also heat is generated uniformly in the wire and the conditions on the outer surface of the wire are uniform. Therefore, it is reasonable to expect the temperature in the wire to vary in the radial r direction only and thus the heat transfer to be one-dimensional. Then we have T=T(r) during steady operation since the temperature in this case depends on r only.

04/11/23 BMCG 2123 Heat Transfer 24

Page 25: Ch2  Conduction

Solution 1

The rate of heat generation in the wire per unit volume:

Nothing that the thermal conductivity is given to be constant, the differential equation that governs the variation of temperature in the wire is simply Eq.2-27

Which steady one-dimensional heat conduction equation in cylindrical coordinates for the case of constant thermal conductivity.

04/11/23 BMCG 2123 Heat Transfer 25

39

22 W/m10318.0

5.04/004.0

2000

4/x

mm

W

LD

E

V

Ee

gen

wire

gengen

01

k

e

dr

dTr

dr

d

rgen

Page 26: Ch2  Conduction

Cylindrical Coordinates

2

1 1gen

T T T T Trk k k e c

r r r r z z t

(2-43)

Page 27: Ch2  Conduction

Spherical Coordinates

22 2 2 2

1 1 1sin

sin sin gen

T T T Tkr k k e c

r r r r r t

(2-44)

Page 28: Ch2  Conduction

Boundary and Initial Conditions

• Specified Temperature Boundary Condition• Specified Heat Flux Boundary Condition• Convection Boundary Condition• Radiation Boundary Condition• Interface Boundary Conditions• Generalized Boundary Conditions

Page 29: Ch2  Conduction

Specified Temperature Boundary Condition

For one-dimensional heat transfer through a plane wall of thickness L, for example, the specified temperature boundary conditions can be expressed as

T(0, t) = T1

T(L, t) = T2

The specified temperatures can be constant, which is the case for steady heat conduction, or may vary with time.

(2-46)

Page 30: Ch2  Conduction

Specified Heat Flux Boundary Condition

dTq k

dx

Heat flux in the positive x-direction

The sign of the specified heat flux is determined by inspection: positive if the heat flux is in the positive direction of the coordinate axis, and negative if it is in the opposite direction.

The heat flux in the positive x-direction anywhere in the medium, including the boundaries, can be expressed by Fourier’s law of heat conduction as

(2-47)

Page 31: Ch2  Conduction

Two Special Cases

Insulated boundary Thermal symmetry

(0, ) (0, )0 or 0

T t T tk

x x

,2 0LT t

x

(2-49) (2-50)

Page 32: Ch2  Conduction

Convection Boundary Condition

1 1

(0, )(0, )

T tk h T T t

x

2 2

( , )( , )

T L tk h T L t T

x

Heat conduction

at the surface in a

selected direction

Heat convection

at the surface in the same direction

=

and

(2-51a)

(2-51b)

Page 33: Ch2  Conduction

Radiation Boundary Condition

Heat conductionat the surface in aselected direction

Radiation exchange at the surface

inthe same direction

=

4 41 ,1

(0, )(0, )surr

T tk T T t

x

4 42 ,2

( , )( , ) surr

T L tk T L t T

x

and

(2-52a)

(2-52b)

Page 34: Ch2  Conduction

Interface Boundary Conditions

0 0( , ) ( , )A BA B

T x t T x tk k

x x

At the interface the requirements are:(1) two bodies in contact must have the same

temperature at the area of contact,(2) an interface (which is a

surface) cannot store any energy, and thus the heat flux on the two sides of an interface must be the same.

TA(x0, t) = TB(x0, t)

and(2-53)

(2-54)

Page 35: Ch2  Conduction

Generalized Boundary ConditionsIn general a surface may involve convection, radiation, and specified heat flux simultaneously. The boundary condition in such cases is again obtained from a surface energy balance, expressed as

Heat transferto the

surfacein all

modes

Heat transferfrom the surface

In all modes

=

Heat Generation in SolidsThe quantities of major interest in a medium with heat generation are the surface temperature Ts and the maximum temperature Tmax that occurs in the medium in steady operation.

Page 36: Ch2  Conduction

The heat transfer rate by convection can also be expressed from Newton’s law of cooling as (W)s sQ hA T T

gens

s

e VT T

hA

Rate ofheat

transferfrom the

solid

Rate ofenergy

generationwithin the

solid

=

For uniform heat generation within the medium (W)genQ e V

-

Heat Generation in Solids -The Surface Temperature

(2-64)

(2-65)

(2-66)

(2-63)

Page 37: Ch2  Conduction

Heat Generation in Solids -The Surface Temperature

For a large plane wall of thickness 2L (As=2Awall and V=2LAwall)

, gen

s plane wall

e LT T

h

For a long solid cylinder of radius r0 (As=2r0L and V=r0

2L) 0, 2

gens cylinder

e rT T

h

For a solid sphere of radius r0 (As=4r02 and V=4/3r0

3)

0, 3

gens sphere

e rT T

h

(2-68)

(2-69)

(2-67)

Page 38: Ch2  Conduction

Heat Generation in Solids -The maximum Temperature in a Cylinder

(the Centerline)The heat generated within an inner cylinder must be equal to the heat conducted through its outer surface.

r gen r

dTkA e V

dr

Substituting these expressions into the above equation and separating the variables, we get 22

2gen

gen

edTk rL e r L dT rdr

dr k

Integrating from r =0 where T(0) =T0 to r=ro2

0max, 0 4

gencylinder s

e rT T T

k

(2-71)

(2-70)

Page 39: Ch2  Conduction

Exercise 3• A 2-kW resistance heater with thermal conductivity k

= 15 W/m.K, diameter D = 4 mm, and length L = 0.5 m is used to boil water. If the outer surface temperature of the resistance wire is Ts = 105oC, determine the temperature at the center of the wire.

• Assumption:– Heat transfer is steady since there is no change with time– Heat transfer is one-dimensional since there is thermal symmetry

about the center line and no change in the axial direction.– Thermal conductivity is constant– Heat generation in the heater is uniform

04/11/23 BMCG 2123 Heat Transfer 39

Page 40: Ch2  Conduction

Solution 3The heat generation per unit volume:

The center temperature of the wire using Eq.2-71

04/11/23 BMCG 2123 Heat Transfer 40

39

220

W/m10318.05.0002.0

2000x

mm

W

Lr

E

V

Ee gen

wire

gengen

C

CmW

mmWx

k

reTT o

oogen

s 126./154

002.0/10318.0105

4

23920

0

Page 41: Ch2  Conduction

Variable Thermal Conductivity, k(T)

• The thermal conductivity of a material, in general, varies with temperature.

• An average value for the thermal conductivity is commonly used when the variation is mild.

• This is also common practice for other temperature-dependent properties such as the density and specific heat.

Page 42: Ch2  Conduction

Variable Thermal Conductivity for One-Dimensional Cases

2

1

2 1

( )T

Tave

k T dTk

T T

When the variation of thermal conductivity with temperature k(T) is known, the average value of the thermal conductivity in the temperature range between T1 and T2 can be determined from

The variation in thermal conductivity of a material with can often be approximated as a linear function and expressed as

0( ) (1 )k T k T the temperature coefficient of thermal conductivity.

(2-75)

(2-79)

Page 43: Ch2  Conduction

Variable Thermal Conductivity

• For a plane wall the temperature varies linearly during steady one-dimensional heat conduction when the thermal conductivity is constant.

• This is no longer the case when the thermal conductivity changes with temperature (even linearly).

Page 44: Ch2  Conduction

Exercise 4• A 2-m-high and 0.7-m-wide bronze plate whose

thickness is 0.1 m. One side of the plate is maintained at a constant temperature of 600 K while the other side is maintained at400 K, as shown in Figure 2.1. Thermal conductivity of the bronze plate can be assumed to vary linearly in the temperature range as K(T)=k0(1+βT) where k0 = 38 W/m.K and β = 9.21x10-4 K-1. Disregarding the effects and assuming steady one-dimensional heat transfer, determine the rate of heat conduction through the plate.

04/11/23 BMCG 2123 Heat Transfer 44

Figure 2.1

Page 45: Ch2  Conduction

Solution 4• The average thermal conductivity of the medium is

simply the value at the average temperature:

• The rate of heat conduction through the plate using Eq. 2-76:

04/11/23 BMCG 2123 Heat Transfer 45

W/m.K5.55

2

4006001021.91./38

21

14

120

KKxKmW

TTkTkk avgavg

kW 155

1.0

4006007.02./5.55

21

m

KmmxKmW

L

TTAkQ avg


Top Related