Chapter 25: UHV/VHF Operation
2
Introduction: First Contacts
• For most amateurs, their first solo-contacts tend to be on 2m or 70cm (VHF/UHF respectively)– Recall: 2m = 144-148 MHz & 70cm = 430-450 MHz– Only basic qualifications required– Affordable equipment for under $100– Relatively simple operating procedures– Offers best introduction to local (established)
amateurs
3
VHF/UHF: Basic overview2M 1.25m 70cm
Frequencies 144-148 MHz 222-225 MHz 430-450 MHz
Band Size 4 MHz 5 MHz 20 MHz
Maximum Bandwidth
30 kHz (FM-wide) 100kHz 12 MHz (DSS)
Calling Frequency
144.100 MHz – CW146.520 MHz – FM
222.1 MHz – CW222.2 MHz – SSB
432.1 MHz – CW432.2 MHz – SSB446.0 MHz – FM
Typical Repeater Offset
0.6 MHz 0.6 MHz 5 MHz
Common Uses
CW, Voice, APRS, Packet, Satellite (U/L)
CW, Voice, Packet CW, Voice, Packet, Satellite (D/L), ATV
Less Common Uses
Remote linking, Moonbounce,
4
Operating: Basic Guidelines
• Listen, Listen, Listen!– No matter what the frequency, ensure that you will not
interrupt a contact in-progress before transmitting– By listening first, you learn the established etiquette on-air
• Use only the minimum power necessary to conduct a contact
• When using a “calling frequency” be sure to QSY once established– Determine a mutually agreed frequency and move to it to
continue chatting• Always comply with the Radiocommunication Act
5
QSO: Methods of making a contact
• There are three possible schemes for making a contact:– Simplex– Half-Duplex– Full-Duplex
• Each method has benefits and drawbacks– Ease of implementation– Cost of hardware associated– Etc..
6
Simplex: The most basic QSO
• Any method of communication which uses the same frequency for transmission and reception
• Only one person may transmit at a time, otherwise, you are “doubling” over each other
• Simplest form of communication• Ex: Walkie-Talkies as a kid
7
Duplex: Using different TX/RX Freq.
• Duplex (half and full) is any method of communication which uses different transmit and receive frequencies
• Half-duplex:– As with simplex, only one person may transmit at a
time for effective communication– Repeaters commonly operate as half-duplex
• Full-duplex:– Seldom used due to the technical challenges– Common example is the cellular telephone
8
Repeaters: A Primer• Repeaters are a very popular resource in
amateur radio• Frequently used by local residents to
improve their “coverage area”• Many local “nets” are hosted on repeaters
because of their enhanced coverage area• May be used to link distant geographic
locations via– RF
• Eg. VE2REH network in Quebec
– Internet• IRLP, Echolink
147.3 MHz
147.9 MHz
9
Repeaters: Major Types
• What:– Any radio station which automatically retransmits
an input signal to increase the effective range of the original signal
– Generally placed in a highly favourable location such as top of a tall building, mountain-top, etc.
Simplex Half-Duplex Full-Duplex
Cross-Band -- HT → Car → APRS iGate
Satellite Operation
Same-Band “Parrot-Box” StandardRepeater
WiFi & Digital “repeaters”
10
Repeaters: Privileges
• Basic licensee:– Use any open repeaters with operating frequencies which are within
the permitted range of the user (ie. your privileges)• Basic (70% < 80%) can use only those repeaters which operate on: 6m, VHF,
UHF• Basic+ (≥80%) may use any repeaters, even those which theoretically
retransmit on HF
– Own/operate a cross-band repeater• In addition to Basic privileges, an Advanced operator may
– Own/operate a same-band repeater• Repeater is generally given its own callsign and the input/output frequency
pairs are supposed to be managed by a repeater council• Must conform to all Radiocommunication Act requirements
– Ie. station identification at least every 30 minutes
11
Repeaters: How It Works
• Simply take an incoming signal and retransmit at higher power, generally in the same band but on a slightly different frequency (the offset)– Generally done with two commercial radios designed
for this purpose (100% duty cycle)• Repeater is generally controlled via DTMF tones
and a controller board– Handles on/off operation, CTCSS tones, identification
• When operating in the same band, a cavity filter (very high Q) is frequently used so that the same antenna can be used for simultaneous TX/RX
12
Coded Squelch: Preventing Noise
• Sub audible tones used in (RF) noisy environment to trigger a radio’s squelch only when a signal with the associated coded squelch is present
• Two major code types:– CTCSS• Continuous Tone-Coded Squelch System
– DCS/DTCS• Digitally (Tone) Coded Squelch
13
CTCSS: Most Common
• As many as 50 sub-audible tones• Originally only 32 tones, but was adapted to incorporate
PL tones (Motorola)
67.0 Hz 94.8 Hz 131.8 Hz 171.3 Hz 203.5 Hz
69.3 Hz 97.4 Hz 136.5 Hz 173.8 Hz 206.5 Hz
71.9 Hz 100.0 Hz 141.3 Hz 177.3 Hz 210.7 Hz
74.4 Hz 103.5 Hz 146.2 Hz 179.9 Hz 218.1 Hz
77.0 Hz 107.2 Hz 151.4 Hz 183.5 Hz 225.7 Hz
79.7 Hz 110.9 Hz 156.7 Hz 186.2 Hz 229.1 Hz
82.5 Hz 114.8 Hz 159.8 Hz 189.9 Hz 233.6 Hz
85.4 Hz 118.8 Hz 162.2 Hz 192.8 Hz 241.8 Hz
88.5 Hz 123.0 Hz 165.5 Hz 196.6 Hz 250.3 Hz
91.5 Hz 127.3 Hz 167.9 Hz 199.5 Hz 254.1 Hz
14
DCS: Seldom Used
• DCS superimposes FSK data (134.4bps) onto the transmitted signal
• Similar to CTCSS, the DCS data serves to prevent squelch opening unless the correct data is received
• Has great potential, however, control boards are more cumbersome to implement
15
Repeaters: How to start
• To use a repeater, you need some information:– Repeater’s TX & RX frequencies
• Repeaters are listed by the frequency at which they transmit
• You must determine the repeater’s receive (listening) frequency by using the offset for the band the repeater is operating on
– Control tone(s) (if used)• Often used in radio-congested areas to reduce unwanted
retransmission of garbage• Generally listed with the repeater’s TX frequency
16
Repeaters: Simple Example
• Let’s use VE3TWO as an example. It is listed simply as:
• This is the repeater’s transmit frequency– Following convention, we know that repeaters which operate on
2m use 0.6 MHz as the offset value (unless otherwise stated)• The (+) means a positive offset frequency for the repeater’s
receive frequency so we add 0.6 MHz to determine the “listening” frequency
147.3 MHz + 0.6 MHz = 147.9 MHz
VE3TWO 147.3 MHz (+)
17
Repeaters: Advanced Example
• Suppose a repeater is listed as:
• To use the repeater, set your radio to:– RX on 147.65 MHz
• using CTCSS tone 151.4 on receive
– TX on 147.05 MHz• using CTCSS tone 110.9 on transmit
*unless otherwise stated, assume that CTCSS tones are listed as (out/in)
VE3FAKE 147.65 MHz (-) (151.4 / 110.9)*
18
Repeater Linking: RF
• Repeaters may be linked to each other by an RF link to increase total coverage area
• When you transmit on repeater A’s input (listen) frequency, all repeaters (including A) retransmit your signal
A
B
C
youdistantstation(Tom)
147.05 MHz
146.3 MHz
147.65 MHz(-)434.86 MHz (-0.6)
146.3 MHz(+)434.86 MHz (-0.6)
147.4 MHz(-)434.80 MHz (+0.6)
147.
4 M
Hz
147.65 MHz
434.86 MHz
434.80 MHz
434.86 MHz
“Hi Tom..”
“Hi Tom..”
“Hi Tom..”
“Hi Tom..”
Blue = 2m “open repeater” frequencyRed = 70cm “rf link” frequencyPTT is pressed
A’s Incoming 70cm RF link locked out by 2m reception (in use)
19
Repeater Linking: Internet
• IRLP– Internet Radio Linking Project
Internet
Radio↔ Repeater (A) Repeater (B) ↔ Radio147.05 MHz(+)Node: 2001
146.7 MHz (-)Node: 2002
•Using your radio which is set to: (TX 147.65MHz, RX 147.05MHz) you would link to the distant repeater by pressing: “2002” on the DTMF keypad while holding the PTT button•Once the IRLP link is established, you could then transmit to your local repeater and have the distant repeater (B) retransmit at 146.7MHz
20
Repeater Linking: Echolink
• Echolink is similar to IRLP with the exception that you can link to distant repeaters directly from a computer, dropping the radio-to-repeater portion of the link
• Theoretically possible to have straight echolink-to-echolink contacts without even using a radio– Not really radio any more, huh?