Download - Circuit theory mt
![Page 1: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/1.jpg)
CIRCUIT THEORY 1
Rojien V. Morcilla, R.E.E., M.Eng’g.
![Page 2: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/2.jpg)
ELECTRIC CIRCUIT
An interconnection of electrical elements.
![Page 3: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/3.jpg)
SYSTEMS OF UNITS
![Page 4: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/4.jpg)
CHARGE AND CURRENT
Charge most basic quantity in an electric circuit is an electrical property of the atomic
particles of which matter consists, measured in coulombs (C).
charge e on an electron is negative and equal in magnitude to 1.602×10−19 C, while a proton carries a positive charge of the same magnitude as the electron. The presence of equal numbers of protons and electrons leaves an atom neutrally charged.
![Page 5: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/5.jpg)
CHARGE AND CURRENT
Points should be noted about electric charge: The coulomb is a large unit for charges. In 1 C of
charge, there are 1/(1.602 × 10−19) = 6.24 × 1018
electrons. Thus realistic or laboratory values of charges are on the order of pC, nC, or μC.
According to experimental observations, the only charges that occur in nature are integral multiples of the electronic charge e = −1.602 × 10−19 C.
The law of conservation of charge states that charge can neither be created nor destroyed, only transferred. Thus the algebraic sum of the electric charges in a system does not change.
![Page 6: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/6.jpg)
CHARGE AND CURRENT
Electric charge or electricity is mobile• Positive charges move in one direction while negative charges move in the opposite direction• Motion of charges creates electric current• Conventionally take the current flow as the movement of positive charges, that is, opposite to the flow of negative charges.
![Page 7: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/7.jpg)
CHARGE AND CURRENT
Electric current is the time rate of change of charge, measured in amperes (A).
Direct Current (DC) is a current that remains constant with time.
Alternating Current (AC) is a current that varies sinusoidally with time.
1 ampere = 1 coulomb/second
![Page 8: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/8.jpg)
CHARGE AND CURRENT (Example)
1. How much charge is represented by 4,600 electrons?2. Calculate the amount of charge represented by two
million protons.3. The total charge entering a terminal is given by q =
5tsin4πt mC. Calculate the current at t = 0.5s.4. If in Example 3, q = (10 − 10e−2t ) mC, find the
current at t = 0.5 s.5. Determine the total charge entering a terminal
between t = 1 s and t = 2s if the current passing the terminal is i = (3t2 − t) A.
6. The current flowing through an element isCalculate the charge entering the element from t = 0 to t = 2s.
![Page 9: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/9.jpg)
VOLTAGE
Voltage (or potential difference) is the energy required to move a unit charge through an element, measured in volts (V).
Voltage vab between two points a and b in an electric circuit is the energy (or work) needed to move a unit charge from a to b; mathematically,
where w is energy in joules (J) and q is charge in coulombs (C).
Voltage vab or simply v is measured in volts (V)1 volt = 1 joule/coulomb = 1 newton meter/coulomb
![Page 10: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/10.jpg)
VOLTAGE
The plus (+) and minus (−) signs are used to define reference direction or voltage polarity.(1)point a is at a potential of vab volts higher than point b
(2)the potential at point a with respect to point b is vab vab = −vba
(a), there is a 9-V voltage drop from a to b or equivalently a 9-V voltage rise from b to a.(b), point b is −9 V above point a.
A voltage drop from a to b is equivalent to a voltage rise from b to a.
constant voltage is called a dc voltage and is represented by V, whereas a sinusoidally time-varying voltage is called an ac voltage and is represented by v.
![Page 11: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/11.jpg)
POWER AND ENERGY
Power is the time rate of expending or absorbing energy, measured in watts (W).
where p is power in watts (W), w is energy in joules (J), and t is time in seconds (s).
power p is a time-varying quantity and is called the instantaneous power.
If the power has a + sign, power is being delivered to or absorbed by the element. If, on the other hand, the power has a − sign, power is being supplied by the element.
![Page 12: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/12.jpg)
POWER AND ENERGY
Passive sign convention is satisfied when the current enters through the positive terminal of an element and p = +vi. If the current enters through the negative terminal, p = −vi.
![Page 13: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/13.jpg)
POWER AND ENERGY
law of conservation of energy must be obeyed:
algebraic sum of power in a circuit, at any instant of time, must be zero.
Energy absorbed or supplied by an element from time t0 to time t is
Energy is the capacity to do work, measured in joules ( J). electric power utility companies measure
energy in watt-hours (Wh)
![Page 14: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/14.jpg)
POWER AND ENERGY (Example)
1. An energy source forces a constant current of 2A for 10s to flow through a light bulb. If 2.3kJ is given off in the form of light and heat energy, calculate the voltage drop across the bulb.
2. To move charge q from point a to point b requires−30 J. Find the voltage drop vab if: (a) q = 2C, (b) q = −6C .
3. Find the power delivered to an element at t = 3 ms if the current entering its positive terminal is i = 5cos60πt A and the voltage is: (a) v = 3i, (b) v = 3 di/dt .
4. Find the power delivered to the element in Example 3 at t = 5 ms if the current remains the same but the voltage is: (a) v = 2i V, (b) v =
5. How much energy does a 100-W electric bulb consume in two hours?
6. A stove element draws 15 A when connected to a 120-V line. How long does it take to consume 30 kJ?
![Page 15: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/15.jpg)
CIRCUIT ELEMENTS
Two types of elements found in electric circuits: Passive element – not capable of generating
energy (resistors, capacitors, and inductors) Active element - capable of generating energy
(generators, batteries, and operational amplifiers) Two kinds of sources:
Independent Sources - an active element that provides a specified voltage or current that is completely independent of other circuit variables
Dependent Sources - an active element in which the source quantity is controlled by another voltage or current. (transistors, operational amplifiers and integrated circuits)
![Page 16: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/16.jpg)
CIRCUIT ELEMENTS
Ideal Independent Voltage Source delivers to the circuit whatever current is necessary to maintain its terminal voltage (batteries and generators).
Symbols for independent voltage sources: (a) used for constant or time-varying voltage, (b) used for constant voltage (dc).
![Page 17: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/17.jpg)
CIRCUIT ELEMENTS
Ideal Independent Current Source is an active element that provides a specified current completely independent of the voltage across the source.
Symbol for independent current source
![Page 18: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/18.jpg)
CIRCUIT ELEMENTS
Four possible types of dependent sources: Voltage-Controlled Voltage Source (VCVS). Current-Controlled Voltage Source (CCVS). Voltage-Controlled Current Source (VCCS). Current-Controlled Current Source (CCCS).
Symbols for: (a) dependent voltage source, (b) dependent current source.
![Page 19: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/19.jpg)
CIRCUIT ELEMENTS
1. Calculate the power supplied or absorbed by each element
2. Compute the power absorbed or supplied by each component of the circuit
![Page 20: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/20.jpg)
OHM’S LAW
Resistance (R) –of an element denotes its ability to resist the flow of electric current; it is measured in ohms (Ω).
The resistance of any material with a uniform cross-sectional area (A) depends on A and its length (l)
where ρ is known as the resistivity of the material in ohm-meters.
Good conductors, such as copper and aluminum, have low resistivities, while insulators, such as mica and paper, have high resistivities.
![Page 21: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/21.jpg)
OHM’S LAW
(a) Resistor, (b) Circuit symbolfor resistance.
![Page 22: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/22.jpg)
OHM’S LAW
Ohm’s law states that the voltage “v” across a resistor is directly proportional to the current “i” flowing through the resistor.
Short circuit is a circuit element with resistance approaching zero.
Open circuit is a circuit element with resistance approaching infinity.
![Page 23: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/23.jpg)
OHM’S LAW
(a) Short circuit (R = 0), (b) Open circuit (R =∞).
![Page 24: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/24.jpg)
OHM’S LAW
Conductance is the ability of an element to conduct electric current; it is measured in mhos ( ) or siemens (S).
Resistance can be expressed in ohms or siemens
The power dissipated by a resistor can be expressed in terms of R.
The power dissipated by a resistor may also be expressed in terms of G
![Page 25: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/25.jpg)
OHM’S LAW
1. An electric iron draws 2 A at 120 V. Find its resistance.
2. In the circuit shown, calculate the current i, the conductance G, and the power p.
3. A voltage source of 20 sin πt V is connected across a 5-k resistor. Find the current through the resistor and the power dissipated.
![Page 26: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/26.jpg)
NODES, BRANCHES, AND LOOPS A branch represents a single element
such as a voltage source or a resistor A node is the point of connection
between two or more branches A loop is any closed path in a circuit. A network with b branches, n nodes, and
l independent loops will satisfy the fundamental theorem of network topology:
b = l + n − 1
![Page 27: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/27.jpg)
NODES, BRANCHES, AND LOOPS Two or more elements are in series if
they are cascaded or connected sequentially and consequently carry the same current
Two or more elements are in parallel if they are connected to the same two nodes and consequently have the same voltage across them.
![Page 28: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/28.jpg)
NODES, BRANCHES, AND LOOPS1. Determine the number of branches and
nodes in the circuit shown. Identify which elements are in series and which are in parallel.
2. How many branches and nodes does the circuit in have? Identify the elements that are in series and in parallel.
![Page 29: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/29.jpg)
KIRCHHOFF’S LAWS
Kirchhoff’s current law (KCL) states that the algebraic sum of currents entering a node (or a closed boundary) is zero.
where N is the number of branches connected to the node and in is the nth current entering (or leaving) the node. By this law, currents enteringa node may be regarded as positive, while currents leaving the node maybe taken as negative or vice versa.
![Page 30: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/30.jpg)
KIRCHHOFF’S LAWS
The sum of the currents entering a node is equal to the sum of the currents leaving the node.
![Page 31: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/31.jpg)
KIRCHHOFF’S LAWS
Kirchhoff’s voltage law (KVL) states that the algebraic sum of all voltages around a closed path(or loop) is zero.
where M is the number of voltages in the loop (or the number of branches in the loop) and vm is the mth voltage.
![Page 32: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/32.jpg)
KIRCHHOFF’S LAWS
By KVL:−v1 + v2 + v3 − v4 + v5 = 0
v2 + v3 + v5 = v1 + v4
Sum of voltage drops = Sum of voltage rises
![Page 33: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/33.jpg)
KIRCHHOFF’S LAWS
1. For the circuit, find voltages v1 and v2.
2. Determine vo and i in the circuit shown.
![Page 34: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/34.jpg)
KIRCHHOFF’S LAWS
3. Find current io and voltage vo in the circuit shown
4. Find the currents and voltages in the circuit shown
![Page 35: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/35.jpg)
SERIES RESISTORS AND VOLTAGE DIVISION
Using Ohms Law
By KVL (clockwise direction)The equivalent resistance of any number of resistors connected in series is the sum of the individual resistances.
![Page 36: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/36.jpg)
SERIES RESISTORS AND VOLTAGE DIVISION
Voltage across each resistor
Principle of Voltage Division - source voltage ‘v’ is divided among the resistors in direct proportion to their resistances; the larger the resistance, the larger the voltage drop.
![Page 37: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/37.jpg)
PARALLEL RESISTORS AND CURRENT DIVISION
By Ohms Law
By KCL @ Node ‘a’
Then:
![Page 38: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/38.jpg)
PARALLEL RESISTORS AND CURRENT DIVISION
Where: The equivalent resistance of two parallel resistors is equal to the product of their resistances divided by their sum.
Req is always smaller than the resistance of the smallest resistor in the parallel combination. If R1 = R2 = … = RN = R, then
![Page 39: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/39.jpg)
PARALLEL RESISTORS AND CURRENT DIVISION
Equivalent conductance for N resistors in parallel :
The equivalent conductance of resistors connected in parallel is the sum of their individual conductance's.
Equivalent conductance Geq of N resistors in series:
![Page 40: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/40.jpg)
PARALLEL RESISTORS AND CURRENT DIVISION
Principle of Current Division - total current ‘i’ is shared by the resistors in inverse proportion to their resistances.
![Page 41: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/41.jpg)
PARALLEL RESISTORS AND CURRENT DIVISION
Divide both the numerator and denominator by R1R2
In general, if a current divider has N conductors (G1,G2, . . . , GN) in parallel with the source current i, the nth conductor (Gn) will have current:
![Page 42: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/42.jpg)
Example
1. Find Req for the circuit shown in Fig. A.
2. Calculate the equivalent resistance Rab in the circuit shown in Fig. B
3. Find the equivalent conductance Geq for the circuit in Fig. C.
Fig. A
Fig. BFig. C
![Page 43: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/43.jpg)
Example
4. Find io and vo in the circuit shown in Fig. D. Calculate the power dissipated in the 3- resistor.
5. For the circuit shown in Fig. E, determine: (a) the voltage vo, (b)the power supplied by the current source, (c) the power absorbed by each resistor.
Fig. DFig. E
![Page 44: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/44.jpg)
WYE-DELTA TRANSFORMATIONS
The bridge network
Two forms of the same network: (a) Y, (b) T.
Two forms of the same network: (a) Δ, (b) π.
![Page 45: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/45.jpg)
WYE-DELTA TRANSFORMATIONS Delta to Wye Conversion
Each resistor in the Y network is the product of the resistors in the two adjacent Δ branches, divided by the sum of the three Δ resistors.
![Page 46: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/46.jpg)
WYE-DELTA TRANSFORMATIONS Wye to Delta Conversion
Each resistor in the Δ network is the sum of all possible products of Y resistors taken two at a time, divided by the opposite Y resistor.
![Page 47: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/47.jpg)
WYE-DELTA TRANSFORMATIONS The Y and Δ networks are said to be
balanced when
Under these conditions, conversion formulas become
![Page 48: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/48.jpg)
Example
1. Convert the Δ network in Fig. A to an equivalent Y network.
2. Obtain the equivalent resistance Rab for the circuit in Fig. B and use it to find current ‘i’.
Fig. A Fig. B
![Page 49: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/49.jpg)
NODAL ANALYSIS
Nodal analysis provides a general procedure for analyzing circuits using node voltages as the circuit variables
Steps to Determine Node Voltages:1. Select a node as the reference node. Assign
voltages v1, v2, . . . , vn−1 to the remaining n − 1 nodes. The voltages are referenced with respect to the reference node.
2. Apply KCL to each of the n − 1 nonreference nodes. Use Ohm’s law to express the branch currents in terms of node voltages.
3. Solve the resulting simultaneous equations to obtain the unknown node voltages.
![Page 50: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/50.jpg)
NODAL ANALYSIS
Current flows from a higher potential to a lower potential in a resistor.
![Page 51: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/51.jpg)
NODAL ANALYSIS
@ Node 1
@ Node 2
Then;
So;
In Terms of Conductance:
In Matrix Form:
![Page 52: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/52.jpg)
NODAL ANALYSIS (Example)1. Calculate the node voltages in the
circuits shown.
![Page 53: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/53.jpg)
NODAL ANALYSIS WITH VOLTAGE SOURCES
Case 1: If a voltage source is connected between the reference node and a nonreference node, we simply set the voltage at the nonreference node equal to the voltage of the voltage source.
Case 2: If the voltage source (dependent or independent) is connected between two nonreference nodes, the two nonreference nodes form a generalized node or supernode; we apply both KCL and KVL to determine the node voltages.
![Page 54: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/54.jpg)
NODAL ANALYSIS WITH VOLTAGE SOURCES
A supernode is formed by enclosing a (dependent or independent) voltage source connected between two nonreference nodes and any elements connected in parallel with it.Note the following properties of a supernode:1. The voltage source inside the supernode
provides a constraint equation needed to solve for the node voltages.
2. A supernode has no voltage of its own.3. A supernode requires the application of both
KCL and KVL.
![Page 55: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/55.jpg)
NODAL ANALYSIS WITH VOLTAGE SOURCES (Example)
1. For the circuits shown, find the node voltages.
![Page 56: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/56.jpg)
NODAL ANALYSIS WITH VOLTAGE SOURCES (Example)
2. Find v and i in the circuit.
![Page 57: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/57.jpg)
MESH ANALYSIS
Mesh analysis provides another general procedure for analyzing circuits, using mesh currents as the circuit variables
A mesh is a loop that does not contain any other loop within it
Nodal analysis applies KCL to find unknown voltages in a given circuit, while mesh analysis applies KVL to find unknown currents
only applicable to a circuit that is planar Planar circuit is one that can be drawn in a
plane with no branches crossing one another; otherwise it is nonplanar.
![Page 58: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/58.jpg)
MESH ANALYSIS
(a) A planar circuit with crossing branches(b) the same circuit redrawn with no crossing
branches(c) A nonplanar circuit.
(c)
![Page 59: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/59.jpg)
MESH ANALYSIS
![Page 60: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/60.jpg)
MESH ANALYSIS (Example)1. For the circuit shown, find the branch
currents I1, I2, and I3 using mesh analysis.
![Page 61: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/61.jpg)
MESH ANALYSIS (Example)2. Calculate the mesh currents i1 and i2 in
the circuit shown.
3. Use mesh analysis to find the current io in the circuit shown.
![Page 62: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/62.jpg)
MESH ANALYSIS (Example)4. Using mesh analysis, find io in the
circuit shown.
![Page 63: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/63.jpg)
MESH ANALYSIS WITH CURRENT SOURCES
Case 1: When a current source exists only in one mesh:
Case 2: When a current source exists between two meshes: We create a supermesh by excluding the current source and any elements connected in series with it.
Set i2 = −5 A and write a mesh equation for the other mesh in the usual way, that is,
![Page 64: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/64.jpg)
MESH ANALYSIS WITH CURRENT SOURCES
A supermesh results when two meshes have a (dependent or independent) current source in common.
(a) Two meshes having a current source in common
(b) a supermesh, created by excluding the current source.
![Page 65: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/65.jpg)
MESH ANALYSIS WITH CURRENT SOURCES
Note the following properties of a supermesh:1. The current source in the supermesh is
not completely ignored; it provides the constraint equation necessary to solve for the mesh currents.
2. A supermesh has no current of its own.3. A supermesh requires the application of
both KVL and KCL.
![Page 66: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/66.jpg)
MESH ANALYSIS WITH CURRENT SOURCES (Example)
1. For the circuit shown, find i1 to i4 using mesh analysis.
![Page 67: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/67.jpg)
MESH ANALYSIS WITH CURRENT SOURCES (Example)
2. Use mesh analysis to determine i1, i2, and i3 in the circuit shown.
![Page 68: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/68.jpg)
LINEARITY PROPERTY
Linearity is the property of an element describing a linear relationship between cause and effect
The property is a combination of both the homogeneity (scaling) property and the additivity property
Homogeneity property requires that if the input (also called the excitation) is multiplied by a constant, then the output (also called the response) is multiplied by the same constant.
![Page 69: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/69.jpg)
LINEARITY PROPERTY
For example, Ohm’s law relates the input i to the output v,
If the current is increased by a constant k, then the voltage increases correspondingly by k, that is,
The additivity property requires that the response to a sum of inputs is the sum of the responses to each input applied separately. Using the voltage-current relationship of a resistor, if
then applying (i1 + i2) gives
![Page 70: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/70.jpg)
LINEARITY PROPERTY
In general, a circuit is linear if it is both additive and homogeneous. A linear circuit consists of only linear elements, linear dependent sources, and independent sources
A linear circuit is one whose output is linearly related (or directly proportional) to its input
Relationship between power and voltage (or current) is nonlinear – linearity theorems are not applicable to power
![Page 71: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/71.jpg)
LINEARITY PROPERTY
Consider the linear circuit shown linear circuit has no independent sources
inside it Excited by a voltage source vs
Terminated by a load R Current i through R as the output Suppose vs = 10 V gives i = 2 A. According to
the linearity principle, vs = 1 V will give i = 0.2 A. By the same token, i = 1 mA must be due to vs =5 mV.
![Page 72: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/72.jpg)
LINEARITY PROPERTY
1. For the circuit, find io when vs = 12 V and vs = 24 V.
2. For the circuit , find vo when is = 15 and is = 30 A.
![Page 73: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/73.jpg)
LINEARITY PROPERTY
3. Assume Io = 1 A and use linearity to find the actual value of Io in the circuit.
4. Assume that Vo = 1 V and use linearity to calculate the actual value of Vo in the circuit.
![Page 74: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/74.jpg)
SUPERPOSITION
The superposition principle states that the voltage across (or current through) element in a linear circuit is the algebraic sum of the voltages across (or currents through) that element due to each independent source acting alone.
To apply the superposition principle, we must keep two things in mind:
1. We consider one independent source at a time while all other independent sources are turned off. This implies that we replace every voltage source by 0 V (or a short circuit), and every current source by 0 A (or an open circuit). This way we obtain a simpler and more manageable circuit.
2. Dependent sources are left intact because they are controlled by circuit variables.
![Page 75: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/75.jpg)
SUPERPOSITION
Steps to Apply Superposition Principle : Turn off all independent sources except one
source. Find the output (voltage or current) due to that active source using nodal or mesh analysis.
Repeat step 1 for each of the other independent sources.
Find the total contribution by adding algebraically all the contributions due to the independent sources.
![Page 76: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/76.jpg)
SUPERPOSITION
1. Use the superposition theorem to find v in the circuit
2. Using the superposition theorem, find vo in the circuit
![Page 77: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/77.jpg)
SUPERPOSITION
3. Find io in the circuit using superposition.
4. Use superposition to find vx in the circuit
![Page 78: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/78.jpg)
SUPERPOSITION
5. For the circuit, use the superposition theorem to find i.
6. Find i in the circuit using the superposition principle.
![Page 79: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/79.jpg)
SOURCE TRANSFORMATION A source transformation is the process of
replacing a voltage source vs in series with a resistor R by a current source is in parallel with a resistor R, or vice versa.
![Page 80: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/80.jpg)
SOURCE TRANSFORMATION
Points to be mind when dealing with source transformation: The arrow of the current source is directed
toward the positive terminal of the voltage source.
Source transformation is not possible when R = 0, which is the case with an ideal voltage source. However, for a practical, nonideal voltage source, R = 0. Similarly, an ideal current source with R =∞cannot be replaced by a finite voltage source.
![Page 81: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/81.jpg)
SOURCE TRANSFORMATION1. Use source transformation to find vo in
the circuit
2. Find io in the circuit using source transformation
![Page 82: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/82.jpg)
SOURCE TRANSFORMATION3. Find vx using source transformation.
4. Use source transformation to find ix in the circuit.
![Page 83: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/83.jpg)
THEVENIN’S THEOREM
Developed in 1883 by M. Leon Thevenin (1857–1926), a French telegraph engineer
Thevenin’s theorem states that a linear two-terminal circuit can be replaced by an equivalent circuit consisting of a voltage source VTh in series with a resistor RTh, where VTh is the open-circuit voltage at the terminals and RTh is the input or equivalent resistance at the terminals when the independent sources are turned off.
![Page 84: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/84.jpg)
THEVENIN’S THEOREM
CASE 1: If the network has no dependent sources, we turn off all independent sources. RTh is the input resistance of the network looking between terminals a and b, as shown
![Page 85: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/85.jpg)
THEVENIN’S THEOREM
CASE 2: If the network has dependent sources, we turn off all independent sources. As with superposition, dependent sources are not to be turned off because they are controlled by circuit variables. We apply a voltage source vo at terminals a and b and determine the resulting current io. Then RTh = vo/io, as shown. Alternatively, we may insert a current source io at terminals a-b as shown in and find the terminal voltage vo. Again RTh = vo/io. Either of the two approaches will give the same result.
![Page 86: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/86.jpg)
THEVENIN’S THEOREM
It often occurs that RTh takes a negative value. In this case, the negative resistance (v = −iR) implies that the circuit is supplying power.
![Page 87: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/87.jpg)
THEVENIN’S THEOREM
1. Find the Thevenin equivalent circuit of the circuit shown, to the left of the terminals a-b. Then find the current through RL = 6Ω, 16Ω, and 36Ω .
2. Using Thevenin’s theorem, find the equivalent circuit to the left of the terminals in the circuit. Then find i.
![Page 88: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/88.jpg)
THEVENIN’S THEOREM
3. Find the Thevenin equivalent of the circuit shown.
4. Find the Thevenin equivalent circuit of the circuit shown to the left of the terminals.
![Page 89: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/89.jpg)
THEVENIN’S THEOREM
5. Determine the Thevenin equivalent of the circuit shown.
6. Obtain the Thevenin equivalent of the circuit.
![Page 90: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/90.jpg)
NORTON’S THEOREM
Developed by E. L. Norton, an American engineer at Bell Telephone Laboratories in 1926, about 43 years after Thevenin published his theorem.
Norton’s theorem states that a linear two-terminal circuit can be replaced by an equivalent circuit consisting of a current source IN in parallel with a resistor RN, where IN is the short-circuit current through the terminals and RN is the input or equivalent resistance at the terminals when the independent sources are turned off.
![Page 91: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/91.jpg)
NORTON’S THEOREM
By Source transformation, the Thevenin and Norton resistances are equal
To find the Norton current IN,we determine the short-circuit current flowing from terminal a to b in both circuits .
Observe the close relationship between Norton’s and Thevenin’s theorems: RN = RTh
![Page 92: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/92.jpg)
NORTON’S THEOREM
Since VTh, IN, and RTh are related, to determine the Thevenin or Norton equivalent circuit requires that we find: The open-circuit voltage voc across
terminals a and b. The short-circuit current isc at terminals a
and b. The equivalent or input resistance Rin at
terminals a and b when all independent sources are turned off.
Thus we find;
![Page 93: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/93.jpg)
NORTON’S THEOREM
1. Find the Norton equivalent circuit of the circuits
2. Using Norton’s theorem, find RN and IN of the circuit at terminals a-b.
![Page 94: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/94.jpg)
NORTON’S THEOREM
3. Find the Norton equivalent circuit of the circuit.
![Page 95: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/95.jpg)
MAXIMUM POWER TRANSFER Circuit is designed to provide power to a load Electric utilities, minimizing power losses in
the process of transmission and distribution is critical for efficiency and economic reasons, there are other applications in areas such as communications where it is desirable to maximize the power delivered to a load
Address problem of delivering the maximum power to a load when given a system with known internal losses.
![Page 96: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/96.jpg)
MAXIMUM POWER TRANSFER Thevenin equivalent is useful in finding
the maximum power a linear circuit can deliver to a load
Maximum power is transferred to the load when the load resistance equals the Thevenin resistance as seen from the load (RL = RTh).
Maximum power transferred is obtained by:
![Page 97: Circuit theory mt](https://reader033.vdocuments.net/reader033/viewer/2022061300/54c8ebce4a795988608b45e1/html5/thumbnails/97.jpg)
MAXIMUM POWER TRANSFER1. Find the value of RL for maximum power
transfer in the circuits. Find the maximum power.