Compact PanelManifolds/Changeover Regulators DCATLABO1259XEN2
The TESCOM Compact Panel is a central gas supply unit for the pressure control of analytical gases in laboratory facilities. Depending on the requirements, these units switch over to a spare cylinder in order to enable a continuous gas supply. The use of contact gauges allows the monitoring of empty gas cylinders.
Applications• Central gas supply for the distribution of gases in
laboratory applications
• Supply of gases for laser cutting applications
• Various other processes requiring continuos gas supply
Features and Benefits• Few connections and minimized internal volume
due to the integration of valves and pressure regulator in one body
• Suitable for ECD (Electron Capture Detector) applications
• Short purging time when changing cylinders
• Purging with process or inert gas
• Easy and quick to maintain - a P & ID is located on front of the panel
• Stainless Steel mounting plate for corrosive environments
• Very compact design (fits into most gas cabinets)
• All versions contain a filter element in the inlet
PANEL FOR 1 CYLINDER WITH CONTACT GAUGE
SpecificationsFor other materials or modifications, please consult TESCOM.
FLUID MEDIA
Non corrosive/corrosive gases and mixtures up to high purity of 6.0 (99.9999 Vol%)
OPERATING PARAMETERSPressure rating per criteria of ANSI/ASME B31.3
Maximum Inlet Pressure
4350 psig / 300 bar
Outlet Pressure Range
0 to 145 psig / 0 to 10 bar
0 to 290 psig / 0 to 20 bar
MaterialNickel-plated Brass or Stainless Steel
Leak Rate10-7 mbar l/s He
Operating Temperature
-4°F to 158°F / -20 °C to 70 °C
Nominal Flow Rate
10 m3/h based on Nitrogen, Cv = 0.06
MEDIA CONTACT MATERIALS
Body
316 Stainless Steel or Nickel-plated Brass
Diaphragm
316L Stainless Steel
OTHERS
Inlet Port Type and SizeG 3/8" femaleCompression fitting 6 mm
Outlet Port Type and SizeProcess Outlet: G 1/4" *Purge Gas: G 1/4" *Relief Valve: M 12x1 **
Cleaning
Cleaned for Oxygen Service
Weight (approximately)
17.6 lbs / 7.9 kg for 2x1 cylinder
8.1 lbs / 3.7 kg for 1 cylinder
* Adapters to all metric and imperial tube sizes available! Please check data sheet “Fittings” for adaptors
** Adapter PIN to metric tube available! Please contact TESCOM.
DUAL STAGE COMPACT PANEL AUTOMATIC CHANGEOVER WITH CONTACT GAUGES
557
558
KP1
(Compact Panel, 1 cylinder, standard manometer)
KPM – Manual changeover
(Compact Panel, 2x1 cylinder, standard manometer)
All dimensions are reference & nominal
Metric [millimeter] equivalents are in brackets
Compact Panel Drawings
Compact Panel Part Number Selector
Repair Kits, Accessories & Modifications may be available for this product. Please contact TESCOM for more information.
Example for selecting a part number:
KP1- 1 KM 1
BASIC SERIES MATERIAL GAUGES OUTLET PRESSURE
KP1 1 Cylinder
KPM 2x1 cylinder, manual changeover
KPA 2x1 cylinder, automatic changeover, single stage
KPA2 2x1 cylinder, automatic changeover, dual stage
1 – Brass
6 – Stainless Steel
SM – Standard gauge
KM – Contact gauge
EX – Inductive contact gauge
KG – Pressure switch
1 – 145 psig / 10.0 bar Set point 145 psig / 10 bar
2 – 290 psig / 20.0 bar Set point 290 psig / 20 bar
Please reference data sheets “Accessories for Panels” and “Fittings” for additional accessories for compact panel.
Please reference data sheet “System Components for Compact Panels” for information about annunciator system and emergency switch-off components.
7.9 [200]
6.7 [170]
IN
INProcess Out
Shut-off Purge
Relief valve
Purge Out
7.9 [200]
6.7 [170]
ININ
Process Out
Shut-off Shut-off
Relief valve
6.7 [170]
16.9 [430]
IN
ININ
IN
Process Out
Shut-offPurge Shut-off Purge
Process Out
Purge Out
Relief valve
Purge Out
6.7 [170]
16.9 [430]
IN
ININ
IN
Process Out
Shut-offPurge Shut-off Purge
Purge Out
Purge Out
Relief valve
KPA2 – Automatic changeover, dual-stage
(Compact Panel, 2x1 cylinder, standard manometer)
KPA – Automatic changeover, single-stage
(Compact Panel, 2x1 cylinder, standard manometer)
Ultra High Purity Compact PanelManifolds/Changeover Regulators DCATLABO1264XEN2
TESCOM Ultra High Purity Compact Panel is a VCR® compatible central gas supply unit for pressure control of high grade analytical gases in laboratory facilities. Depending on the requirements, these units switch over to a spare cylinder in order to enable an uninterrupted gas supply. The use of contact gauges allows the monitoring of empty gas cylinders, in combination with an annunciator.
Application
• Central gas supply for the distribution of gases in laboratory applications
Advantages
• VCR® technology for high purity application
• Automatic changeover for continuous gas supply
• Integrated purge and shut-off valve for fast purging
• Optional Hastelloy® trim and positive seal for corrosive media
• Field-proven TESCOM 64 Series regulator design
SpecificationsFor other materials or modifications, please consult TESCOM.
REGULATOR
Maximum Inlet Pressure1000 or 3480 psig / 69.0 or 240 bar
Outlet Pressure Range145, 247 psig / 10.0, 17.0 bar maximum
Body Material316L Stainless Steel
Regulator SeatPCTFE
Valve SeatCeramic on Stainless Steel
Remaining Parts316 Stainless Steel
Flow Capacity< 9 Nm3/h at Cv = 0.06 trim
Leak Rate1x10-8 mbar l/s He
Operating Temperature-40°F to 140°F / -40°C to 60°C
GAUGESMaterial
Stainless Steel
Connection1/4" HPIC (VCR® compatible internal connection)
RELIEF VALVEOutlet Connection
6 mm Compression fitting
Body MaterialStainless Steel 1.4404
Seat MaterialViton®
CONTACT GAUGES 2.5"Material
Stainless Steel
Scale Range2900 or 4570 psig / 200 or 315 bar (other ranges on request)
SwitchReed switch, opens with decreasing pressure
Surge Current1 A
Permanent Current0.6 A
Power30 Watt, 50 VA
Cable3 wire, 2 m length
OTHERSWeight
Single Cylinder Panel: 8.2 lbs / 3.7 kgAutomatic Changeover Panel: 18.5 lbs / 8.4 kg
Hastelloy® is a registered trademark of Haynes International. VCR® is a registered trademark of Swagelok.Viton® and Vespel® are registered trademarks of E.I. du Pont de Nemours and Company.
559
560
Ultra High Purity Compact Panel Drawing
All dimensions are reference & nominal
Metric [millimeter] equivalents are in brackets
Standard Features:Stainless Steel mounting plate, regulator with integrated valves, inlet/outlet pressure gauges and relief valve. All connections 1/4" HPIC.
Ultra High Purity Compact Panel Part Number Selector
Repair Kits, Accessories & Modifications may be available for this product. Please contact TESCOM for more information.
7.87 [200]
7.0
9 [
180]
6.65 [169]
7.2
4 [
184]
6.72 [170.7]18.9 [480]
CYLINDER PANEL STAINLESS STEEL AUTOMATIC CHANGEOVER SYSTEM
SINGLE CYLINDER PANEL
AUTOMATIC CHANGEOVER PANEL
CYLINDER PRESSURE OUTLET PRESSURE
PURGE
VALVE
SHUT-OFF
VALVE
P1 P2
CYLINDER PRESSURE CYLINDER PRESSURE OUTLET PRESSURE
P1 P1 P2
PURGE
VALVE
SHUT-OFF
VALVE
PURGE
VALVE
SHUT-OFF
VALVE
FUNCTIONAL DIAGRAMSINGLE CYLINDER PANEL
OPEN AND CLOSE VALVES SLOWLY OPEN AND CLOSE VALVES SLOWLY
FUNCTIONAL DIAGRAMAUTOMATIC CHANGEOVER PANEL
Example for selecting a part number:
D45429 - SM - S - 2 - XXX
TYPE GAUGES VALVE UNIT OUTLET PRESSUREOPTIONS
(PLEASE CONSULT FACTORY)
D45429 – Single Cylinder Panel
D45450 – Automatic Changeover Panel
SM – Standard gauges
KM – Contact gauges
S – Untied
P – Positive Seal
1 – 145 psig / 10.0 bar
2 – 247 psig / 17.0 bar
• Cv = 0.15 or Cv = 0.24
• Inlet filter
• Vespel® regulator seat
• Pigtail with cylinder connector
System Components for Compact PanelsManifolds/Changeover Regulators DCATLABO12166XEN2
The annunciator system is used in combination with a cylinder station in order to avoid a complete discharge of the cylinder which would cause an interruption of the process. The annunciator system consists of a signal box, the pressure switches or contact gauges and the electrical wiring. For Explosion Proof environments a Switch Amplifier Box (Ex-Modul) must be added. The annunciation consists of an integrated horn, lights or an additional external indicator.
Application
• Easy continuous monitoring of gas storage
Features and Benefits
• One annunciator system monitors up to 10 contact pressure gauges
• Acoustical and optical signals
• Error messages can be forwarded to external systems using potential-free relay contacts
Annunciator System
OPERATING PARAMETERSPressure rating per criteria of ANSI/ASME B31.3
Power Supply Connection: Terminal clamp X4, cage clamps Voltage: 230 V AC, 50 Hz Power Consumption: < 3 VA
Outlets Connection: Terminal clamp X3, cage clamps Type: Change-over relay contact, potential-free Load: 8A/230 V AC ohmic load Function: Collective error report Connection: Terminal clamp X2, cage clamps Type: Change-over relay contact, potential-free Load: 8A/230 V AC ohmic load Function: Non-confirmed error report
Inputs Connection: Terminal clamp X1, 2-tier cage clamps Number: SK-02: 2 inputs SK-06: 6 inputs SK-10: 10 inputs Type: internal direct current supply to the inputs, potential free Voltage between terminals: approximately 6 VC / 10 mA
Dimensions Casing: 7.9" x 4.7" x 3" / 200 mm x 120 mm x 75 mm (WxHxD) Protection: IP65 Material: ABS Joints: 4 x M16 Ambient temperature: 32°F to 131°F / 0 °C to 55 °C
Annunciator signal box
Switch Amplifi er Box
561
562
Emergency Switch-Off System(Solenoid Valve, Control Box and Emergency Switch)
The emergency switch-off system acts in case of emergency or other hazardous events as an electrical operated quick shut-off for main pipe systems, floor pipe systems or room pipe systems. All gas supplies will be stopped at the feeding points already. In combination with a control box and a gas warning system the emergency switch-off system is an important part of the central gas supply system.
Applications
• Solenoid valves control the gas stream after the compact panels
• The Solenoid Valve Control Box is needed to control solenoid valves in case an emergency shut-down is necessary
• Safety device according TRG 280
Features and Benefits
• Easy to install
• Reliable design
• Long-life system
SOLENOID VALVE TYPE 214 SOLENOID VALVE TYPE 220Nominal Width / Connection
DN 10 / G 1/4" internalOperating Pressure
0-260 psig / 0-18 barFunction
2/2-way powerless closedVoltage
230 V AC, 50 HzType of Protection
IP65 / Ex EEx em II T4Body Material
Brass / Stainless SteelSeatsFor Ex-Version: FPMFor all IP65-Types: EPDM
Nominal Width / ConnectionDN 10 / G 3/8" internalOperating Pressure*
2.9-145 psig / 0.2-10 barFunction
2/2-way powerless closedVoltage
230 V AC, 50 HzType of Protection
IP65 / Ex EEx em II T4Body Material
Brass / Stainless SteelSeatsFor Ex-Version: FPMFor all IP65-Types: EPDM
*Do not use for line pressures below 3 psig / 200 mbar.
SOLENOID VALVE CONTROL BOX SPECIFICATIONS
Voltage230 V AC, 50 HzInput Power
< 3 VADimensions for Box Width x Height x Depth
200 x 120 x 75 mmMaterial
ABSProtection
IP65Ambient Temperature
32°F to 131°F / 0 °C to 55 °C
Solenoid Valve
Solenoid Valve Control Box
563
Annunciator System Drawing
Annunciator Signal Box - Interface Panel
Confi rmation Switch
Red Light for Gas Failure
Power
Room A Room B Room C
Solenoid ValveControl Box
Gas Detection SystemGas Failure Warning
Supply Channel
Floor Shut-Off Room Shut-off
Room A Room B Room C
Room Shut-off
Compact Panel Compact Panel
Non-flammable gases Flammable gases
Gas Storage
Ground Floor
1st Floor
11
2
2
1
2
Point of use
Shut-off solenoid valve
Emergency shut-off switch
Measuring head
Drop Point below minimum storage
Legend:
E
564
Annunciator Signal Box
D44542 - 02 EX2
BASIC SERIES OPTION USAGE
D44542 02 – Dual 06 – Sixfold
010 – Tenfold
Annunciator system via 2 contact gauges – not for Ex zonesAnnunciator system via 6 contact gauges – not for Ex zonesAnnunciator system via 10 contact gauges – not for Ex zones
Annunciator Signal Box + Switch Amplifi er Box
BASIC SERIES USAGE
D44542-00-EX2 EX-Modul 2 D44542-00-EX6 EX-Modul 6
D44542-00-EX10 EX-Modul 10
Annunciator + Switch amplifier dual for signal box 2 for Ex-proof areasAnnunciator + Switch amplifier sixfold for signal box 6 for Ex-proof areasAnnunciator + Switch amplifier tenfold for signal box 10 for Ex-proof areas
Emergency Switch-Off System Number Selector
Repair Kits, Accessories & Modifications may be available for all products. Please contact TESCOM for more information.
Solenoid Valve
BASIC SERIES NOMINAL WIDTH BODY MATERIAL PROTECTION OPTIONS
D45093 04 – DN 3.5 Valve Type 21410 – DN 10 Valve Type 220
1 – Brass 6 – Stainless Steel
[BLANK] – IP65 (this is standard) EX – Ex EEx em T4
A –24 V DC[BLANK] –230 V AC (this is standard)
Solenoid Valve Control Box
BASIC SERIES NUMBER OF CONTROLLED SOLENOID VALVES
D44700 05 – 5 Valves
10 – 10 Valves
Emergency Switch
PART NUMBER DESCRIPTION DRAWING
V09556 Emergency-Switch
Key-operated: After emergency switch-off, the keymust be turned to activate the system again.
Material: Stainless SteelType of protection: IP54 or EX II 1 G EExia IIC T6Connection: G 1/4" maleDiameter: 2.48" / 63 mm
PRESSURE RANGE* ORDERING NUMBER: REED CONTACT MINIMUM SWITCH POINT ORDERING NUMBER: INDUCTIVE CONTACT**
4569 psi / 315 bar5802 psi / 400 bar580 psi / 40.0 bar
580 psi / 40.0 bar Acetylene
D44500-00G3156D44500-00G4006D44500-00G0406
- - - -
218 psi / 15.0 bar290 psi / 20.0 bar
44 psi / 3.0 bar12 psi / 1.5 bar
D44272-00G3156D44272-00G4006D44272-00G0406D44272-22G0406
Contact Pressure Gauges
* Please, contact us for additional pressure ranges and connection types (e.g. NPT or VCR®).**For use with EX-proof version!
Certificate EN 10204-2.2 available - Please, add “Z“ at the end when ordering!
High Pressure PanelManifolds/Changeover Regulators DCATLABO1282XEN2
TESCOM High Pressure Panel is a central gas supply unit for the pressure control of analytical gases in laboratory facilities. The use of contact gauges allows the monitoring of the filling pressure of gas cylinders.
Applications
• High pressure central gas supply for the distribution of gases in laboratory applications
• Suitable for ECD (Electronic Capture Detector) applications
Features and Benefits
• For very high work pressures up to 2175 psig / 150 bar
• Inlet section with purge valve, purging with process or inert gas
• Easy to use and safe operation (includes relief valve)
• Few connections and minimized internal volume due to the integrated design of valves and pressure regulators in one body
• Quick and simple installation
• Small dimensions
• Stainless Steel mounting plate for corrosive environment
• High pressure, explosion proof contact gauge is available
SpecificationsFor other materials or modifications, please consult TESCOM.
FLUID MEDIA
For non-corrosive gases and mixtures up to purity 6.0 (99.9999 Vol %)
OPERATING PARAMETERSPressure rating per criteria of ANSI/ASME B31.3
Maximum Inlet Pressure
2900 psig / 200 bar
4350 psig / 300 bar
Outlet Pressure Range
2175 psig / 150 bar
Operating Temperature
-4°F to 158°F / -20°C to 70°C
Nominal Flow
10 m3/h, Cv = 0.06 (depending on pressure and gas)
MEDIA CONTACT MATERIAL
Material
Chrome plated Brass or Stainless Steel
OTHER
Connections
6 mm compression fitting or G 3/8" female
Other outlet options on request
Weight
9.26 lbs / 4.2 kg
565
566
High Pressure Panel Drawing
All dimensions are reference & nominal
Metric [millimeter] equivalents are in brackets
7.87 [200]
7.7
2 [
196]
6.6
9 [
170]
8.8
6 [
225]
INLET
INLET
OU
TLE
T
PR
OC
ES
S G
AS
OU
TLE
T
PU
RG
E G
AS
INLET
INLET
OU
TLE
T
PR
OC
ES
S G
AS
OU
TLE
T
PU
RG
E G
AS
INLET INLET
INLET
OU
TLE
T
PU
RG
E G
AS
INLETINLET INLET
INLET INLET
7.7
2 [
196]
6.6
9 [
170]
8.8
6 [
225]
16.93 [430]
WITH STANDARD GAUGES WITH CONTACT GAUGES OR
INDUCTIVE CONTACT GAUGES
WITH STANDARD GAUGES WITH CONTACT GAUGES OR
INDUCTIVE CONTACT GAUGES
HIGH PRESSURE PANEL FOR 1 CYLINDER
HIGH PRESSURE PANEL FOR 2 CYLINDERS WITH AUTOMATIC CHANGEOVER
567
High Pressure Panel Functional Diagram
HIGH PRESSURE PANEL FOR 1 CYLINDER
HIGH PRESSURE PANEL FOR 2 CYLINDERS WITH AUTOMATIC CHANGEOVER
OUTLET PRESSURE
SHUT-OFF VALVE RELIEF / PURGE
RE
LIE
F
PU
RG
E
OUTLET
CYLINDER PRESSURE
P1P2
INLET
INLE
T
OUTLET PRESSURE
SHUT-OFF VALVE SHUT-OFF VALVE RELIEF / PURGERELIEF / PURGE
RE
LIE
F
PU
RG
E
PU
RG
E
OU
TLE
T
CYLINDER PRESSURECYLINDER PRESSURE
P1 P2
INLETINLET
INLE
T
INLE
T
P1
568
High Pressure Panel Flow Chart
High Pressure Panel Part Number Selector
Repair Kits, Accessories & Modifications may be available for this product. Please contact TESCOM for more information.
Example for selecting a part number:
KP1 6 SM 3
BASIC SERIES MATERIAL GAUGES OUTLET PRESSURE RANGE
KP1KPA
1 – Brass6 – Stainless Steel
SM – Standard gauge KM – Contact gauge
EX – Inductive contact gauge
3 – 2175 psig / 150 bar
For more information on how to read flow curves, please refer to the Flow Curves and Calculations document (debul2007x012) in the TESCOM catalog or on www.tescom.com.
OU
TL
ET
PR
ES
SU
RE
- p
sig
[b
ar]
0
1
1
1
2
2
2
3
FLOW RATE - SCFM [SLPM] Nitrogen
2500
[172]
2000
[138]
1500
[103]
1000
[69]
500
[35]
10
[283]
20
[566]
30
[849]
40
[1132]
50
[1416]
MODEL 44-1812-24
INLET P1 = psig [bar]
1 = 3000 [207]
2 = 1500 [103]
3 = 500 [35]
Please reference the “Accessories for Panels” datasheet in the Manifolds/Changeover Regulators section or “Fittings” in the Accessories section for pigtail or high pressure hoses, etc.
Accessories for PanelsManifolds/Changeover Regulators DCATLABO12159XEN2
High Pressure Pigtail Assemblies
The pigtail assembly consists of a metal cylinder lead, that is either a looped tube or a flexible hose with a gas specific connector at one end and a compression fitting at the other end. It is used to interconnect the Compact Panel manifold to a storage gas cylinder or a cylinder bundle. Loop construction permits spacing adjustments between cylinders. TESCOM Pigtails are made of Stainless Steel and available for various national gas cylinder valves. TESCOM Pigtails are designed for high pressure applications up to a nominal pressure of 4350 psig / 300 bar. All TESCOM Pigtails are manufactured with a compression fitting 6 mm.
High Pressure Pigtail Part Number Selector
HDS-9-3-F – High pressure fl exible hose for Oxygen according to DIN 477-1, 2900 psig / 200 bar, No.9.
Example part number:
HDS - 9 - 3 - F
PIGTAIL TYPE
BASIC SERIES
CYLINDER CONNECTION – National Standard* LENGTH OPTIONS ** CERTIFICATES
Flexible hose
HDS
N – NPT 1/4" female 1 – DIN 477-1, 200 bar, No.16 – DIN 477-1, 200 bar, No.69 – DIN 477-1, 200 bar, No.910 – DIN 477-1, 200 bar, No.1013 – DIN 477-1, 200 bar, No.1314 – DIN 477-1, 200 bar, No.1454 – DIN 477-5, 300 bar, No.5455 – DIN 477-5, 300 bar, No.5556 – DIN 477-5, 300 bar, No.5657 – DIN 477-5, 300 bar, No.5759 – DIN 477-5, 300 bar, No.59LU1 – NEN3268, LU1LU4 – NEN3268, LU4LI2 – NEN3268, LI2RI2 – NEN3268, RI2RU1 – NEN3268, RU1RU3 – NEN3268, RU3RU4 – NEN3268, RU4RU6 – NEN3268, RU6BS3 – BS 341, No.3BS4 – BS 341, No.4BS8 – BS 341, No.8
1 – 1 m2 – 2 m3 – 3 m5 – 5 m
F – Anti-whip cable mounted to the hose; with incorporated fixtures or loops for external fixing
E – Integrated purging valve to control the purging of the hose system before disconnecting
L – 90° Elbow at cylinder connection to prevent the kinking and cracking of the hose at cylinder or bundle side
Z – 3.1
Pigtail rigid
HDW
– C – curved end (standard)S – straight end
* Other National Standards on request, for example CGA or AFNOR. Spare Parts (O-Rings, Gaskets) available on request.
FLEXIBLE HOSE PIGTAIL, STAINLESS STEEL WITH ANTI-KINK SPRINGS PIGTAIL RIGID, LOOPED TUBE, STAINLESS STEEL
*Contains just compression ring.
Option E – Integrated purging valveRequired for KPM, manual changeover
Option L – 90° Elbow
Standard: Anti-Kink Springs
*
HDW with straight ends
*
HDW with curved endsOption F – Anti-Whip cable
** Other options available on request
569
570
Additional Accessories Ordering Information
PART NUMBER DESCRIPTION
D44924Gas Cylinder bracket (wall mounted type)
224
199
ø 10
30
52
3
D02316Sintered filter for inlet connection of compact panel(Brass version)
D44274-xx-01
• Gas type label 70 x 270 x 1.5 (lasered)
• Please indicate gas type when ordering
• Gas table D41716 will be sent on request
COMPRESSION FITTING FOR OUTLET, G 1/4" MALE
METRIC TUBE SIZE
PART NUMBER RELATING TO MATERIAL
Brass Stainless Steel
6 mm D40619 D40579
8 mm D42669 D42754
10 mm D41756 D41933
12 mm D44792 ERAA02388
IMPERIAL TUBE SIZE
Ø 1/8'' D41329 D41362
Ø 1/4'' D41328 D41360
Ø 3/8'' B-600-1-4RS SS-600-1-4RS
Ø 1/2'' – D51252
FITTINGS FOR RELIEF VALVE OUTLET, MATERIAL BRASS
THREAD TUBE SIZE PART NUMBER
M12x1 Ø 8 mm D51275
Manifold Extension Kit for Automatic or Manual Changeover Compact Panel
Facilitates the extension of the 2 x 1 CP; allows for the connection of additional cylinders to the CP system. Mounted on wall bracket. Available in two versions:
1. Manifold with shut-off valve
Enables the exchange of an empty cylinder without the interruption of the gas flow.
2. Manifold without shut-off valve
Pure extension function. Cylinders must be changed at the same time.
Manifold Extension Kit Part Number Selector
ERCA02607-1LV – Manifold extension, brass, design left, with shut-off valve.
Example part number:
ERCA02607 - 1 L V
BASIC SERIES MATERIAL ORIENTATION SHUT-OFF VALVE
ERCA02607 1 – Brass 6 – Stainless Steel
L – Left R – Right
V – with shut-off valve T – without shut-off valve
10.9 inch / 277 mm
4.8 inch / 122 mm
6.9
in
ch
/ 1
70
mm
7.9 inch / 200 mm10.9 inch / 277 mm
3.0 inch / 77 mm
6.9
in
ch
/ 1
70
mm
7.9 inch / 200 mm