CORANGAMITE CMA SOIL HEALTH STRATEGY
Identification andmanagement of soil erosion
Produced for the Corangamite Catchment ManagementAuthority by the Victorian Department of Primary Industries
Cover Photos: Soil erosion presents a threat to natural and builtassets in the Corangamite region.
Compiled by : Laurie Norman, Ian Crook and Troy Clarkson.
2
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
Contents
Introduction – Soil erosion 4
How does erosion occur? 5
Impacts and implications of soil erosion 6
Soil erosion in the field 8
Known extent of soil erosion sites in Corangamite CMA region 12
Field recognition and on-the-spot tests 14
Road construction and soil erosion 15
Road maintenance 16
Key points to remember about soil erosion 18
Further information 19
A FIELD GUIDE: SOIL EROSION 3
CONTENTS
TITLE PAGE
4
Introduction – Soil erosion Soil erosion – by water or wind – is costly, withimpacts on natural and built assets includinginfrastructure, water quality, biodiversity and in somecases, human safety.
It occurs because soils have not been protected from theforces of wind, raindrop impact or running water in sheets,rills, gullies or tunnels.
Wind erosion occurs on dry, exposed surfaces andcan be aggravated by disturbance of the exposed soilsurface by vehicular traffic, livestock (just walking for feedor water) or cultivation. The keys to controlling wind erosionare wet soil (not always feasible); surface cover (ideally byvegetation) and a lack of disturbance.
Erosion by water is much the more important form oferosion in the Corangamite region. Although a naturallyoccurring phenomenon – just one of the forces that hascreated the landscape – it is unwanted and uncontrolledsoil erosion by water that creates costs for infrastructuremanagers, landholders, and local government - with a verysignificant but little-appreciated damage to all forms of lifein streams, creeks and rivers that feed into water suppliesand the wider environment.
Defining soil erosion. Soil erosion is the detachment,transportation and deposition of soil by water or wind.Eroded soil in transport is ‘sediment’; sedimentation occurswhen sediment is deposited. The rate of erosion dependson the climate, soil, topography, plant cover and land use.
It all starts with raindrops.Leaving wind erosion to oneside, the first and most importantstage in soil erosion by water isthe impact of the raindrop.
Fig.1: Research has shown that rainfalling at an intensity of 50mm/hr for30 minutes generates sufficientenergy to raise the top 10cm of soilto a height of 45cm.
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
A FIELD GUIDE: SOIL EROSION 5
How does erosion occur?
In simple terms, erosion occurs because the energy inwater is sufficient to overcome the inertia and other forcesthat are holding soil particles in place.
The start – rain drops of sufficient size and/or intensityimpact the soil, impart the energy they have acquiredthrough falling, impact the soil surface and createdisturbance. Water, failing to infiltrate, then starts to ‘run’across the soil surface, wherever there is a gradient andgravity at work.
Step 2 – Sheet erosion – water movement across thesoil surface begins sheet erosion. This can be over verysmall or very large areas. Generally, sheet erosion isassociated with larger areas of shallow water movingacross the soil surface.
Step 3 – Rill erosion – rills are small, eroding channelsacross the soil. They can be naturally occurring channelsor indentations before erosion begins or they can becreated - for instance from the ridges and valleys left bycultivation or other mechanical means. Water runs fromsheets large and small into these channels. In thisconcentrated form, the running water now as smallrivulets picks up soil particles and erosion begins.
Step 4 – Gully erosion – gullies are larger rills –sometimes many metres deep. They are generally steep-sided and can be metres deep, and cut through top soilinto sub-soil layers and even bedrock. Most gullies formin natural drainage lines and are generally precipitated byclearing upstream which itself leads to sheet and rillerosion. Gullies can also be formed from the collapse ofsurface soil into an eroded sub-surface area.
Tunnel erosion – the most insidious form of erosionbecause it is generally taking place out of view, under thesurface. Tunnel erosion is the subsurface erosion of soilthat becomes apparent only when signs of subsoil appearon the surface or the tunnel collapses.
HOW DOES EROSION OCCUR?
6
Impacts and Implicationsof soil erosion
Sedimentation is a majorimpact of soil erosion. The implications ofsedimentation include:
• Blocking of culverts withsediment reducing theflow of run-off wateroff site
• Blocking of flow underbridge resulting inbridge damage andfailure
• Loss of valuable topsoilcontaining nutrients
• Reducing capacity ofdrainage basin causingdiversion and flooding.
Tunnel erosion The insidious nature oftunnel erosion makes itextremely dangerous whenworking machinery onareas affected by tunnels.Tunnels can also createstructural problems ifsituated near buildingdevelopment.
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
Blocking of culverts
Blocking of flow under bridge
Loss of valuable topsoil
Reducing capacity of drainage
Tunnel erosion
Tunnel erosion
A FIELD GUIDE: SOIL EROSION 7
IMPACTS OF EROSION
Gully erosion will impacton and destroy publicutilities including roads,communication lines, waterpipes, etc. Gullies alsodisrupt access acrosscultivation paddocks andare a hazard for stock andmachinery movement.Gullies are also a majorcontributor of sediment tothe system.
Erosion on roads can beextremely dangerous forroad users and creates ahigh maintenancerequirement.
Wind erosion removesvaluable topsoil andnutrients, with impacts onhealthy living and towns.Wind erosion can alsobecome a traffic by hazardreducing visibility.
Fig. 2: Examples of impacts caused by soil erosion.
8
Soil erosion in the field
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
Sheet Erosion on steep hills removes the topsoil andplant nutrients and develops a hard impermeable surfacewhich increases the rate of run-off, creating furthererosion problems down-slope.
Fig. 3: An example of sheet erosion.Photo: Peter Dahlhaus.
Sheet and rill erosion can be a major contributor ofsediment to public infrastructure such as roads andstreams.
Fig.4: An example of sheet and rill erosion.Photo: Troy Clarkson.
A FIELD GUIDE: SOIL EROSION 9
SOIL EROSION IN THE FIELD
Rill erosion in a paddock situation can create problemswith paddock trafficability and concentrates water flowwhich, if unattended, increases velocity and leads toformation of gullies.
Gully erosion in a paddock situation can causedisruption to cultivation, stock movement and generalaccess across the paddock. Sediment from the gully canimpact on public utilities such as roads and bridges.
Fig. 6: An example of gully erosion.Photo: Laurie Norman.
Fig. 5: An example of rill erosion.
10
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
The first sign of tunnel erosion is yellow clay emanatingfrom pop-holes or formation of silt fans. The final stage isthe collapse of the tunnel and formation of a gully.
Fig. 7 & 8: Examples of tunnel erosion.Photos: Peter Dahlhaus.
Tunnel erosion can cause havoc on building blocks.There was no sign of this problem prior to its collapse.
A FIELD GUIDE: SOIL EROSION 11
SOIL EROSION IN THE FIELD
Wind erosion destroys the soil structure and fertility byblowing away the fine soil particles which also contain soilnutrients. Wind-blown soil can impact on paddockstructures such as fencing and water supplies, as well aspublic amenities, roads, houses and road safety during awind storm.
Formal risk assessment in the field can be purely byobservation of the landscape on site. Observations thatcan be useful in determining the potential risk of soilerosion occurring include:
• Light coloured subsoil can be highly dispersible andtherefore prone to erosion if not protected.
• Topography: Steep slopes will discharge water fasterreducing infiltration and increasing potential forerosion.
• Length of slope: Long slopes will allow run-off togather speed and volume, increasing the potential forerosion.
• Vegetation cover: Bare soil will increase erosionpotential by both wind and water.
Fig. 9: An example of wind erosion.Photo: Peter Dahlhaus.
12
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
Known extent of soil erosionsites in Corangamite CMAregionPlease note: There is a series of CMA region-wide andShire maps covering the different forms of erosion,including susceptibility maps. Shown below is a selection.Full details in the manual and from the website.
Tunnel Erosion Sites
CORANGAMITE
GLENELG HOPKINS
PORT PHILLIP & WESTERNPORT
NORTH CENTRAL
Colac
Terang
Cressy
Lismore
CobdenTorquay
Skipton
Macedon
GEELONG
Ballarat
Werribee
Mortlake
Beaufort
Anglesea
Lorne
Blackwood
Lake Bolac
Inverleigh
Camperdown
Apollo Bay
Cape Otway
Princetown
Glenaire
Queenscliff
Diggers Rest
Port Campbell
Riddells Creek
Tunnel Erosion sitePublic Land
0 10 20 30 405
Kilometres
Gully Erosion Sites
Corangamite Catchment Management Authority Gully Erosion Susceptibility
Fig.10: Known tunnel erosion sites in Corangamite Catchment ManagementAuthority region.
Fig. 11: Gullyerosionsusceptibility inin CorangamiteCatchmentManagementAuthorityregion.
A FIELD GUIDE: SOIL EROSION 13
KNOWN EXTENT OF SOIL EROSION SITES IN CORANGAMITE CMA
Colac-Otway Shire Gully erosion Susceptibility
Colac-Otway Shire GullyErosion Susceptibility
Fig. 12: Gully erosionsusceptibility in
Colac-Otway Shire.
14
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
Field recognition and on-the-spot testsSoil Stability Test:
This is a simple test used to determine if the soil isdispersive and if it slakes. This is a modification of thelaboratory-based Emerson Dispersion Test.You can carryout the test simply with rainwater or distilled water. Fulldetails in the manual.
Unlike dispersion, slaking is amechanical process and occurs whenthe soil structure is weak. When a drysoil is wet rapidly, water moves intopores within the aggregate and forcesair out. The force of the escaping air
causes the aggregate to burst. The soil microaggregatesare washed into the soil and block soil pores and form acrust on the soil surface. In the field, soil crusting can becaused by slaking or dispersive soils.
Organic matter is important as a treatment for holding soilparticles together and preventing them from slaking.
Complete dispersion A cloud of dispersed clay covers thebottom of the dish and the aggregatehas almost disappeared.
Incomplete dispersionThe dispersed clay spreads in thinstreaks and crescents on the bottomof the container.
What does this mean for treating the soil?In the field, a dispersible soil may suffer from severecrusting, erosion and poor drainage. When wet, the soilloses all structure with the clay particles dissolving inwater. This means the soil can be easily transported,leading to all types of water erosion - including tunnelerosion – and high impact on water quality.
Fig. 13: Soil aggregates dispersing and slaking in water.
A FIELD GUIDE: SOIL EROSION 15
ROAD CONSTRUCTION AND SOIL EROSION
Road construction andsoil erosionRoads are a major source of erosion and sediment.Gravel roads have an inherent potential for causingerosion. They have a surface, batters and table drains ofsubsoil material which is frequently erodible and exposedto splattering action of raindrops.
Fig. 14: Gully erosion forming along a road side.Photo: Peter Dahlhaus.
Roads have a surface, batters, and tabledrains of subsoilmaterial which is frequently erodible and continuallyexposed to erosion by rain and surface run-off. Note thatthis road has no apparent opportunity to divert run-offaway from the road.
Location of roadsCareful location of a road can significantly reduce itsconstruction, drainage and maintenance costs. Where the velocity of water is doubled, its capacity toerode and transport sediment increases 64 times. It istherefore important to provide more drains and use gentlegradients wherever possible.
16
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
Road maintenance
A considerable amount of careful planning and work goesinto construction of a stable road free of acceleratederosion, but this continued state is often destroyed bypoor maintenance.
The four most common problems are:
• Failing to re-open mitre or cut-off drains blocked byroad surface grading
• Leaving an unnecessary ridge or bank of gradedearth or gravel along the outside edge of the road sothat the water cannot flow freely off the road butconcentrates instead to scouring volumes andvelocities
• Removing the toe of the cut-off batters whilst clearingout table drains with a grader. This often upsets thewhole stability of the cut batter, leading to furtherundercutting by water in the table drains, causingeither slumps or the onset of rill erosion
• Dumping unwanted sediment from drains, or materialfrom cut batter slumps, where the table drain andother drains discharge at the end of the cut section.
Fig. 15: A cut off drain blocked by road grading must be re-opened for effective road drainage.
A FIELD GUIDE: SOIL EROSION 17
ROAD MAINTENANCE
Fig. 16: Removal of the toe of the cut batter during grading upsetsthe stability of the batter leading to slumping or rilling andblocking of table drains.
Fig. 17: Soil from the slumped cut batters or silted table drainsshould not be dumped near culvert or table drain outlets.
18
CORANGAMITE CMA SOIL HEALTH STRATEGY 2008-2012
Key points to rememberabout SOIL EROSION
Municipality Gully & Sheet LandslidesStreambank & Rill
Erosion Erosion
City of Ballarat 93 228 20
City of Geelong 178 288 117
Colac Otway 153 139 3,189
Corangamite 49 27 931
Golden Plains 1,603 777 48
Moorabool 709 1,125 379
Surf Coast 128 119 224
Other shires 11 32 36adjacent to the CCMA region
Totals 2,924 2,735 4,944
Overall total of erosion & landslide features = 10,603
• As at April 2007 there are 5659 mapped erosion sitesin the CCMA Region
• As a guide, positional accuracy may range from+/- 25m to +/-200m
• Also as a guide, there may be many more incipient orpotential soil erosion that have not been identified bythe surveying techniques used so far
• Many of the mapped sites intersect roads, railways orother infrastructure where human activity has createdpredisposing factors
• Further human activity may create triggering factors;climatic factors may also create ‘triggers’.
Whilst the capture and collation of information and data isongoing, the current number of mapped occurrences (as of April 2007) of erosion and landslide by municipalitywithin the CCMA region is shown in the following table.
Individual erosion inventory maps have been produced byCorangamite Catchment Management Authority for each shire atboth local government area scale and at 1:25,000 scale forindividual map sheets.
A FIELD GUIDE: SOIL EROSION 19
Further Information
Contact your Supervisor who will have access to moredetailed information on soil erosion from theCorangamite Catchment Management Authority.Additional information also available on the CCMA SoilHealth Web site at www.ccma.vic.gov.au/soilhealth
Acknowledgement: Much of this information has beensourced from other documents and full reference isgiven in the accompanying training manual.
FURTHER INFORMATION
Disclaimer:
This publication may be of assistance to you, but theCorangamite Catchment Management Authority, itsemployees and other contributors do not guarantee thatthe publication is without flaw of any kind or is whollyappropriate for your particular purposes and thereforedisclaim all liability from error, loss or other consequencethat may arise from you relying on any information in thispublication. Further, specific references to funding levelsin this publication are for indicative purposes only. Thelevel of Government investment in this publication iscontingent on budgets and Government priorities.
8555 Erosion Field Guide 16/4/08 8:45 AM Page 19
GS
DM
_855
5
Corangamite Catchment Management Authority
64 Dennis Street, Colac. 3250
T: 03 5232 9100 E: [email protected]
W: www.ccma.vic.gov.au
For further information on Soil Health in the Corangamite region:www.ccma.vic.gov.au/soilhealth