Nov
emb
er
2006
Ed
itio
n
Corrosion Resistant Polypropylene Fan Catalogue
Laboratory & Industrial Fume Extraction
www.axair-fans.co.uk
2 Axair Fans UK Ltd 01782 349 430
...About Axair Fans UK
• 230V or 115V single phase motor• 230/400V three phase direct-on-line or inverter supplied motor• 400/690V three phase star-delta connection in larger motor sizes.• Pre-wired electrical isolators• Motor starters• Inverter drives• Fume cupboard air alarms
• ATEX motor
• Choice of handing• Choice of standard or weather pedestals• Anti-vibration mountings• Flexible connectors• Flange pairs• Duct transformations• Manual dampers• Drain hose connectors• ATEX polypropylene/carbon fans
Lowfi eld Drive - Centre 500 - Wolstanton - Newcastle-under-Lyme - ST5 0UUTel : 01782 349430 Fax : 01782 349439 Email : [email protected] www.axair-fans.co.uk
All specifi cations, data and drawings are subject to alterations without prior notice
Application Knowledge : 20 years experience in general air movement; including corrosive, explosive and hot fume handling.
Plastic range : 9 basic sizes of polypropylene fan in plain scroll housing from stock, plus 3 sizes of in-line fan on short lead-time.
Stock facility: Large modern warehouse facility containing a vast selection of fans, fan components and general accessories.
Customised build: Fans assembled from standard components to create the perfect mechanical and electrical solution to safe fume extraction.
Customer care : Experience a sense of partnership with Axair Fans.
Axair offers you a wide range of electrical options including :
Axair offers you a wide range of mechanical options including :
Motors & Accessories
All polypropylene fans are directly driven by IEC dimensioned electric motors manufactured to BS4999-EN60034 Standards and are selected on their capacity for:
• Low electro-magnetic vibration
• Dimensional compactness
• Inverter drive compatibility
• Electrical terminal accessibility
• IP55 dust and hosed water protection
• Integrity of surface fi nish
Accessories
Motors
• Flange pairs with sockets to fi t standard plastic
ductwork. These can provide an easy method of
disconnecting the fan stack in situations where a disconnecting the fan stack in situations where a
fl exible connector is impractical.
• Pre-wiring of electrical isolators to the motor
terminals to ensure fi rst class electrical work in
factory conditions and an isolator on the fan
pedestal.
• Fume cupboard ‘low air’ alarms and air speed
controls that are modern sophisticated
products requiring no special training to install
and commission.
AXAIR polypropylene fans are the best starting point for a fully functional and reliableinstallation, but are just the fi rst consideration. It is the total ‘system’ that providesultimate customer satisfaction and a desire to repeat the experience. With that in mind we offer:-
disconnecting the fan stack in situations where a
• Mechanical isolation of the fan from the ductwork by means of chemical resistant and truly fl exible
duct connectors, attached by quick-release stainless steel band clips.
• Mechanical isolation of the fan from the motor pedestal or base by means of rubber anti-vibration
mountings of the correct hardness and compression.
4 Axair Fans UK Ltd 01782 349 430
Product Coding System
Index
SEAT ‘S’ FanElectrical data, sound levels & dimensions
Page 5
‘S’ Fan on weatherpadestal
Dimensions
Page 8
STORM ‘ST’ FanElectrical data, sound levels & dimensions
Page 9
‘ST’ Fan on weather pedestal
Dimensions
Page 12
Accessories
Page 13
ATEXCategory 3Consult Axair
Model abbreviationS: SEAT fume cupboard and general duty polypropylene fan ST: STORM fi lter duty and general low fl ow / higher pressure fanJ: JET in-duct and roof mounted in-line fan
Model numberS & J range impeller diameter (cm)ST model number
Scroll housing ‘handling’R: Right handed or clockwise rotation on the fan inlet (Eurovent LG)L: Left handed or anti-clockwise rotation on the fan inlet (Eurovent RD)
Inlet & discharge diameter75 ST1090 ST12125 ST14 & S15160 ST16, S20 & J20200 S25 & J25250 S30 & J30315 S35
Motor & impeller rotational speed
2 2 pole or 2870/min4 4 pole or 1450/min6 6 pole or 930/min
ATEX Flameproof
EX Where stated
Electrical supply
1 Single phase electrical supply3 Three phase electrical supply
Pedestal
STD Standard steel pedestal for indoor and sheltered installationsBOX Weather protecting polypropylene box pedestal
S 25 R /200 /4 EX /1 /STD
SEAT ‘S’ Fans
SEAT ‘S’ range fans are designed to provide high air fl ow rate against medium system pressures; typical applications being the extract of corrosive fumes from laboratory fume cupboards and industrial process tanks.
Notes: Tabulated current values are approximate and depend on make and model of motor.Size the wiring with a built-in safety factor. Set current overload protection to A(Full Load)A (Full Load) = Motor full load current - to select wiring and current overload protection.A (Start) = Motor starting current - mainly advisory for motors with Y/∆ facility.To obtain 230V 3phase current multiply 400V A(Full Load) by 1,732.* ∆ connected 400V direct-on-line. Y/∆ switching reduces starting current to 1/3 x A(Start).
Sound Level
Electrical DataModel /min kW Motor V A
(full load)A
(start)V A
(full load)A
(start)S15/2 2870 0,37 71-2 230 2,8 7 400 1,2 6S15/4 1450 0,25 71-4 230 2,0 5 400 1,0 5S20/2L 2870 0,55 71-2 230 3,8 9 400 1,5 7S20/2M 2870 0,75 80-2 230 5,1 14 400 1,8 10S20/2H 2870 1,10 80-2 230 7,0 19 400 2,5 14S20/4 1450 0,25 71-4 230 2,0 5 400 1,0 5S20/6 930 0,18 71-6 230 1,9 5 400 0,9 2,5S25/2L 2870 1,50 90S-2 230 10,8 28 400 3,7 20S25/2M 2870 2,20 90L-2 230 14,6 63 400 5,1 34S25/2H 2870 3,00 90L-2 400 6,9 49S25/4 1450 0,37 71-4 230 3,4 8 400 1,2 5S25/6 930 0,18 71-6 230 1,9 5 400 0,9 2,5S30/4 1450 1,50 90L-4 230 10,5 28 400 3,7 20S30/4L 1450 0,75 80-4 230 4,9 27 400 2,2 10S30/6 930 0,75 90S-6 230 4,8 16 400 2,2 8,0S35/4 1450 5,50 112M-4 400 11,4∆ *75∆S35/4H 1450 7,50 132M-4 400 14,7∆ *96∆S35/6 930 2,20 112M-4 400 5,3Y 24Y
Model /min dB(A) 63 125 250 500 1000 2000 4000 8000 Hz
S151450 58 39 52 60 64 64 60 56 48 dB(A)2870 75 56 69 77 81 81 77 73 65 dB(A)
S20960 53 34 47 55 59 59 55 51 43 dB(A)
1450 65 46 59 67 71 71 67 63 55 dB(A)2870 81 62 75 83 87 87 83 79 71 dB(A)
S25960 59 42 55 63 67 68 64 60 51 dB(A)
1450 69 52 65 73 77 78 74 70 61 dB(A)2870 87 70 83 91 95 96 92 88 79 dB(A)
S30930 63 48 61 69 73 74 70 66 57 dB(A)
1450 75 60 73 81 85 86 82 78 69 dB(A)
S35930 75 71 81 83 86 85 85 83 74 dB(A)
1450-5.5kW 79 75 85 87 90 89 89 87 78 dB(A)1450-7.5kW 84 80 90 92 95 94 94 92 83 dB(A)
THREE PHASESINGLE PHASE
SEAT ‘S’ range curves are in Total Pressure, as
appropriate for ducted systems.
The Pv characteristic is the Fan Velocity Pressure.
The performance available from the fan is
affected by the speed at which air leaves the
ventilation system and the KW rating of the
motor. For performances beyond the PV curve,
please consult Axair.
6 Axair Fans UK Ltd 01782 349 430
Performance Characteristics (50Hz)
S25 / 200
S35 / 315
S20 / 160
S30 / 250
S15 / 125
Handings
8 discharge angles available for each
direction of rotation RD or LG.
Applicable for all types except S35,
(available in LG handings only)
MODEL A B C ØD E F G H L M P Y Y1 Z X X1
S15/125/2&4 170 240 203 125 100 32 115 30 70 80 360 180 160 340 240 71
S20/160/2L,4&6 208 303 240 160 100 57 143 32 84 94 390 180 160 340 240 71
S20/160/2M&H 208 303 240 160 100 57 143 32 84 94 390 180 160 340 240 80
S25/200/4&6 248 365 310 200 103 92 164 35 95 105 415 180 160 420 300 71
S25/200/2L,M&H 248 365 310 200 103 92 164 35 95 105 515 240 220 460 370 90
S30/250/4&6 300 450 373 250 117 112 198 35 110 120 540 240 220 460 370 90
S30/250/4L 300 450 373 250 117 112 198 35 110 120 540 240 220 460 370 80
S35/315/4 370 570 450 315 130 170 255 60 150 170 724 350 314 600 468 112
S35/315/4H 370 570 450 315 130 170 255 60 150 170 822 350 314 600 468 132
S35/315/6 370 570 450 315 130 170 255 60 150 170 724 350 314 600 468 112
Dimensional Data
‘S’ Fan on a Box Pedestal
‘S’ range polypropylene fan on a weather-protecting
box pedestal (the drawing shows handing LG90 – other
handings available).
Dimensions of pedestal
Dimensions of scroll housing
8 Axair Fans UK Ltd 01782 349 430
MODEL A B C ØD E F G H L Q
S15 170 240 203 125 100 32 115 30 70 90
S20 208 303 240 160 100 57 143 32 84 104
S25 248 365 310 200 103 92 165 35 95 115
S30 300 448 373 250 117 112 198 35 110 130
S35 370 570 450 315 130 170 255 60 150 180
MODEL Motor R U1 U2 V V1 W W1
S15 all sizes 71 450 75 315 260 200 320 250
S20 0.25kW - 0.55kW 71 480 75 315 260 200 320 250
S20 0.75kW - 1.1kW 80 480 85 365 260 200 330 260
S25 0.37kW 71 505 76 374 260 200 330 260
S25 1.5kW - 2.2kW - 3kW 90 610 95 455 365 300 400 330
S30 all sizes 90 640 95 455 365 300 400 330
S35 5.5kW 112 880 122 578 500 400 585 480
S35 7.5kW 132 880 142 558 500 400 585 480
STORM ‘ST’ FansSTORM ‘ST’ range fans are designed to provide relatively low air fl ow rate against elevated system pressures; typical applications being air fi ltration, local extraction arms, fume scrubbers and chemical stores.
Electrical Data
Sound Level
Model /min kW Motor VA
(full load)A
(start)V A
(full load)A
(start)
ST 10/2 2870 0,12 56-2 230 1,4 2 400 0,5 6
ST 10/4 1450 0,09 56-4 230 1,0 1,5 400 0,4 1
ST 10/2/1E 1450 0,07 ERM(1) 230 0,11
ST 12/2 2870 0,37 71-2 230 2,8 7 400 1,2 6
ST 12/2 1450 0,25 71-4 230 2,0 5 400 1,0 5
ST 14/2 2870 1,10 80-2 230 7,0 19 400 2,5 14
ST 16/2 2870 2,20 90L-2 230 14,6 63 400 5 34
SINGLE PHASE THREE PHASE
/min dB(A) 63 125 250 500 1000 2000 4000 8000 Hz
ST12 2870 75 56 69 77 81 81 77 73 65 dB(A)
ST14 2870 79 60 73 81 85 85 81 77 69 dB(A)
ST16 2870 84 65 78 86 90 90 86 82 74 dB(A)
(1) ERM : external rotor motor
Notes: Tabulated current values are approximate and depend on make and model of motor.Size the wiring with a built-in safety factor. Set current overload protection to A(Full Load)A (Full Load) = Motor full load current - to select wiring and current overload protection.A (Start) = Motor starting currentTo obtain 230V 3phase current multiply 400V A(Full load) by 1,732.
(ST10 fi gures not available)
Sound power (Lw) in dB(A) at specifi ed frequency (Hz)Sound pressure at 3m range in dB(A)
10 Axair Fans UK Ltd 01782 349 430
Performance Characteristics (50Hz)
ST10 / 75 ST12 / 90
ST16 / 160ST14 / 125
STORM ‘ST’ range curves are in Static Pressure, as appropriate
for applications requiring elevated pressures.
The PV characteristic is the Fan Velocity Pressure
Dimensional Data
Handing
8 discharge angles available.
MODEL A B C ØD E G H L M N P Y Y1 Z X X1
ST10/75/2&4 115 135 127 75 158 97 32 48 57 - - 140 - 260 130 56
ST10/75/4/1E 115 135 127 75 158 97 32 48 57 - 205 - - - - -
ST10/75/4/1E/BKT(*) 115 135 127 75 158 97 32 48 57 - 205 - 100 165 135 -
ST12/90/4/2&4 145 175 163 90 212 130 45 80 72 10 350 180 160 340 240 71
ST14/125/2 188 232 227 125 218 170 55 110 83 10 433 180 160 340 240 80
ST16/160/2 235 288 278 160 262 205 40 100 97 10 477 240 160 420 370 90
(*) BKT : Right-angled bracket supporting the inlet side of fan housing
12 Axair Fans UK Ltd 01782 349 430
‘ST’ Fan on a Box Pedestal
‘ST’ range polypropylene fan on a weather-protecting
box pedestal (the drawing shows handing LG90 – other
handings available).
Dimensions of pedestal
Dimensions of scroll housing
MODEL A B C ØD E G H L Q
ST12 145 175 203 90 212 130 45 80 82
ST14 188 232 227 125 218 170 55 110 93
ST16 235 288 278 160 262 205 40 100 107
MODEL Motor P U1 U2 V V1 W W1
ST12 0,37kW 422 75 315 260 200 320 250
ST14 1,1kW 463 85 365 260 200 330 260
ST16 2,2kW 572 95 455 365 300 400 330
Duct Adaptor
Manual Damper
Flexible Connector & Quick Release Clips
Drain Hose ConnectorAdjustable Height
AV Mountings
Armoured Cable Gland
Weather Protecting Pedestal
Pre-wired IsolatorSingle Phase
Plastic Cable Gland
Pre-wired IsolatorThree phase
Metal Pedestal
Plastic Cable GlandDrain Hose
Connector
Flexible Connector & Quick Release Clips
AV Mountings
Manual Damper
Duct AdaptorSocket Flanges
Accessories
AccessoriesS15 S20 S25 S30 S35
Ø125 Ø160 Ø200 Ø250 Ø315
AV Mounting(Ø20x15 rubber bobbin)
AVB-M6 AVB-M6 AVB-M6 (1) (1)
AV Mounting(Ø25x22 rubber bobbin)
(1) (1) AVB-M8 (S25/2) AVB-M8 (1)
AV Mounting(2)
(25 high rubber turret)(1) (1) (1) (1) AVT-M8
Flexible connector & stainless clips
FLX-125 FLX-160 FLX-200 FLX-250 FLX-315
Socket PVC flange (1) FLG-160 FLG-200 FLG-250 FLG-315
PVC adaptor(Ø125/160) DAD-1216(Ø125/200) DAD-1220
(Ø160/200) DAD-1620
(Ø200/250) DAD-2025(Ø200/315) DAD-2031
(Ø250/315) DAD-2531
(Ø315/355) DAD-3135
Manual damper DAM-125 DAM-160 DAM-200 DAM-250 DAM-315
Pre-wired isolatorSingle phase
IPW-1 IPW-1 IPW-1 IPW-1 IPW-1
Pre-wired isolatorThree phase
IPW-3 IPW-3 IPW-3 IPW-3 (1)
Drain hose connector(Ø12PP)
HOC-3812 HOC-3812 HOC-3812 HOC-3812 HOC-3812
Fume cupboard alarm
LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)
AccessoriesST10 ST12 ST14 ST16
Ø75 Ø90 Ø125 Ø160
AV Mounting(Ø20x15 rubber bobbin)
(1) AVB-M6 AVB-M6 (1)
AV Mounting(Ø25x22 rubber bobbin)
(1) (1) (1) AVB-M8
AV Mounting(2)
25 high rubber turret(1) (1) (1) (1)
Flexible connector & stainless clips
(1) (1) FLX-125 FLX-160
Socket PVC flange (1) (1) (1) 815401
PVC adaptor (1) (1)(Ø125/160) DAD-1216(Ø125/200) DAD-1220
(Ø160/250) DAD-1620
Manual damper (1) (1) DAM-125 DAM-160
Pre-wired isolatorSingle phase
(1) IPW-1 IPW-1 IPW-1
Pre-wired isolatorThree phase
(1) IPW-3 IPW-3 IPW-3
Drain hose connector (1) HOC-3812 HOC-3812 HOC-3812
Fume cupboard alarm (1)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)
14 Axair Fans UK Ltd 01782 349 430
(1) Consult Axair Fans for details & availability(2) Also available for all weather boxesLABAIR-A(3) Fume cupboard air alarm & monitorLABAIR-A(4) Fume cupboard air alarm, monitor & air speed controller (when used in conjunction with an inverter or motorised damper)
‘S’ F
an
s‘S
T’ F
an
s
AccessoriesS15 S20 S25 S30 S35
Ø125 Ø160 Ø200 Ø250 Ø315
AV Mounting(Ø20x15 rubber bobbin)
AVB-M6 AVB-M6 AVB-M6 (1) (1)
AV Mounting(Ø25x22 rubber bobbin)
(1) (1) AVB-M8 (S25/2) AVB-M8 (1)
AV Mounting(2)
(25 high rubber turret)(1) (1) (1) (1) AVT-M8
Flexible connector & stainless clips
FLX-125 FLX-160 FLX-200 FLX-250 FLX-315
Socket PVC fl ange (1) FLG-160 FLG-200 FLG-250 FLG-315
PVC adaptor(Ø125/160) DAD-1216(Ø125/200) DAD-1220
(Ø160/200) DAD-1620
(Ø200/250) DAD-2025(Ø200/315) DAD-2031
(Ø250/315) DAD-2531
(Ø315/355) DAD-3135
Manual damper DAM-125 DAM-160 DAM-200 DAM-250 DAM-315
Pre-wired isolatorSingle phase
IPW-1 IPW-1 IPW-1 IPW-1 IPW-1
Pre-wired isolatorThree phase
IPW-3 IPW-3 IPW-3 IPW-3 (1)
Drain hose connector(Ø12PP)
HOC-3812 HOC-3812 HOC-3812 HOC-3812 HOC-3812
Fume cupboard alarm
LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)
AccessoriesST10 ST12 ST14 ST16
Ø75 Ø90 Ø125 Ø160
AV Mounting(Ø20x15 rubber bobbin)
(1) AVB-M6 AVB-M6 (1)
AV Mounting(Ø25x22 rubber bobbin)
(1) (1) (1) AVB-M8
AV Mounting(2)
25 high rubber turret(1) (1) (1) (1)
Flexible connector & stainless clips
(1) (1) FLX-125 FLX-160
Socket PVC fl ange (1) (1) (1) 815401
PVC adaptor (1) (1)(Ø125/160) DAD-1216(Ø125/200) DAD-1220
(Ø160/250) DAD-1620
Manual damper (1) (1) DAM-125 DAM-160
Pre-wired isolatorSingle phase
(1) IPW-1 IPW-1 IPW-1
Pre-wired isolatorThree phase
(1) IPW-3 IPW-3 IPW-3
Drain hose connector (1) HOC-3812 HOC-3812 HOC-3812
Fume cupboard alarm (1)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)LABAIR-A(3)
LABAIR-C(4)
Labair
Air Speed Alarms & Controllers for Laboratory Fume Cupboards
Compliant with EU laboratory standard EN-14175Electromagnetic standard EN 61326, RoHS Directive, CE 12
Standard Features
Display: 2 green LED - normal air speed 1 green LED - high air speed 1 red LED fl ashing - ‘low air’ 1 orange LED fl ashing - ‘sash high’ 1 orange LED - calibration Test: Fan, Mute & Light LED test facility
Alarms: Audible buzzer for ‘low air’ speed alarm Audible buzzer for ‘sash high’ alarm
Settings: Alarm delay for 0s, 10s or 30s System purge for 0s or 30s
Buttons: Start/stop, with orange LED, for fume fan & air make-up fan Mute to cancel audible alarms Light cupboard, with orange LED
Mounting: Flush or Surface Box with IP55 seal 210 x 90 fascia x 10 deep Vertical and horizontal options
Supply: 230Vac/12Vdc power supply included
Sensor: Ø22 tube. 3,5m shielded cable. Included: Calibrated 0,5m/s. Recalibration facility.
Options
Relay to switch for an external alarm device
Battery back-up for red LED.
Rechargeable and lasting up to 12 hours
Fascia colour white, dark grey, or silver plastic
Logo plate printed to customer requirements (100pieces minimum)
3 digit air speed display in m/s
UK 3 pin plug on 230V power supply lead
Models
LABAIR-A is a basic air speed monitor and alarm
LABAIR-C has PID outputs to an inverter speed controller or to air damper drive electronics
The purpose of LABAIR-C is to maintain a fi xed air speed at the fume cupboard sash face regardless of sash height, to save heat extraction from the laboratory, and to prevent draughts within the fume cupboard
Both models are available with LED Display only, or with Digital Display of air speed in m/s
Lowfield DriveCentre 500WolstantonNewcastle-under-LymeST5 0UUTel : 01782 349430Fax : 01782 349439
Email : [email protected]
ww
w.a
xair
-fan
s.co
.uk
Lowfield DriveCentre 500WolstantonNewcastle-under-LymeST5 0UUTel : 01782 349430Fax : 01782 349439
Email : [email protected]