Download - Diploma i boee u 2 dc circuit analysis
![Page 1: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/1.jpg)
DC circuit analysis
Course: Diploma
Subject: Basics of Electrical Engineering
Unit: II
![Page 2: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/2.jpg)
What is DC circuit?• Direct current (DC) circuits basically consist
of a loop of conducting wire (like copper)through which an electric current flows. Anelectric current consists of a flow of electriccharges, analogous to the flow of water (watermolecules) in a river. In addition to the copperwire in a circuit there usually are componentssuch as resistors which restrict the flow ofelectric charge, similar to the way rocks anddebris in a river restrict the flow of the riverwater.
![Page 3: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/3.jpg)
Continue..
• Common DC circuit diagram is shown in figure containing resistors and battery.
Fig 1
![Page 4: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/4.jpg)
Voltage source• A voltage source is a two terminal device
which can maintain a fixed voltage. An idealvoltage source can maintain the fixed voltageindependent of the load resistance or the outputcurrent. However, a real-world voltage sourcecannot supply unlimited current. A voltage sourceis the dual of a current source. Real-world sourcesof electrical energy, such as batteries, generators,and power systems, can be modeled for analysispurposes as a combination of an ideal voltagesource and additional combinationsof impedance elements.
![Page 5: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/5.jpg)
Cont..
A schematic diagram of a real voltage source, V, driving a resistor, R, and creating a current I
Fig 2
![Page 6: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/6.jpg)
Ideal voltage source• An ideal voltage source is a two-terminal device
that maintains a fixed voltage drop across its terminals. It is often used as a mathematical abstraction that simplifies the analysis of real electric circuits. If the voltage across an ideal voltage source can be specified independently of any other variable in a circuit, it is called an independent voltage source. Conversely, if the voltage across an ideal voltage source is determined by some other voltage or current in a circuit, it is called a dependent or controlled voltage source.
![Page 7: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/7.jpg)
Cont..
• A mathematical model of an amplifier will include dependent voltage sources whose magnitude is governed by some fixed relation to an input signal, for example. In the analysis of faults on electrical power systems, the whole network of interconnected sources and transmission lines can be usefully replaced by an ideal (AC) voltage source and a single equivalent impedance
![Page 8: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/8.jpg)
Cont..
Ideal Voltage Source
Controlled Voltage SourceSingle cell
Battery of cells
Fig 3
![Page 9: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/9.jpg)
Current sources• A current source is an electronic circuit that delivers or
absorbs an electric current which is independent of the voltage across it.
• A current source is the dual of a voltage source. The term constant-current 'sink' is sometimes used for sources fed from a negative voltage supply. Figure 1 shows the schematic symbol for an ideal current source, driving a resistor load. There are two types – an independent current source (or sink) delivers a constant current. A dependent current source delivers a current which is proportional to some other voltage or current in the circuit.
![Page 10: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/10.jpg)
Cont..
Ideal Current Source
Controlled Current Source
Fig 3
![Page 11: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/11.jpg)
Dependent and independent source
• Dependent sources:-
• In the theory of electrical networks, a dependent source is a voltage source or a current source whose value depends on a voltage or current somewhere else in the network.
• Dependent sources are useful, for example, in modeling the behavior of amplifiers. A bipolar junction transistor can be modeled as a dependent current source whose magnitude depends on the magnitude of the current fed into its controlling base terminal.
![Page 12: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/12.jpg)
Cont..
• An operational amplifier can be described as a voltage source dependent on the differential input voltage between its input terminals. Practical circuit elements have properties such as finite power capacity, voltage, current, or frequency limits that mean an ideal source is only an approximate model. Accurate modelling of practical devices requires using several idealized elements in combination.
![Page 13: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/13.jpg)
Classification
Dependent sources can be classified as follows:a)Voltage-controlled voltage source: The source delivers
the voltage as per the voltage of the dependent element.b)Voltage-controlled current source: The source delivers the
current as per the voltage of the dependent element.c)Current-controlled current source: The source delivers the
current as per the current of the dependent element.d)Current-controlled voltage source: The source delivers the
voltage as per the current of the dependent element.
![Page 14: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/14.jpg)
Circuits
Voltage-controlled voltage source
Voltage controlled current source
Current controlled current source
Current controlled voltage source
Fig 4
![Page 15: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/15.jpg)
Independent sources
• An independent voltage source maintains a voltage (fixed or varying with time) which is not affected by any other quantity. Similarly an independent current source maintains a current (fixed or time-varying) which is unaffected by any other quantity. The usual symbols are shown in figure
![Page 16: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/16.jpg)
Symbols
• Symbols for dependent sources
![Page 17: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/17.jpg)
Star Delta connection circuit
• The Y-Δ transform, also written wye-delta and also known by many other names, is a mathematical technique to simplify the analysis of an electrical network. The name derives from the shapes of the circuit diagrams, which look respectively like the letter Y and the Greek capital letter Δ. This circuit transformation theory was published by Arthur Edwin Kennelly in 1899. It is widely used in analysis of three-phase electric power circuits.
• The Y-Δ transform can be considered a special case of the star-mesh transform for three resistors.
![Page 18: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/18.jpg)
Cont..
Page No. 1.19 from Elements of Electrical Engineering ( J.N.Swamy)
![Page 19: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/19.jpg)
Cont..
• The transformation is used to establish equivalence for networks with three terminals. Where three elements terminate at a common node and none are sources, the node is eliminated by transforming the impedances. For equivalence, the impedance between any pair of terminals must be the same for both networks. The equations given here are valid for complex as well as real impedances.
• Equations for the transformation from Δ-load to Y-load 3-phase circuit
• The general idea is to compute the impedance at a terminal node of the Y circuit with impedances , to adjacent node in the Δ circuit by
![Page 20: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/20.jpg)
Cont..
• where are all impedances in the Δ circuit. This yields the specific formulae
![Page 21: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/21.jpg)
Cont..• Equations for the transformation from Y-load to
Δ-load 3-phase circuit.• The general idea is to compute an impedance in
the Δ circuit by
• where is the sum of the products of all pairs of impedances in the Y circuit and is the impedance of the node in the Y circuit which is opposite the edge with . The formula for the individual edges are thus
![Page 22: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/22.jpg)
Cont..
![Page 23: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/23.jpg)
Kirchhoff's laws• Kirchoff’s current law:-• This law is also called Kirchhoff's first
law, Kirchhoff's point rule, or Kirchhoff's junction rule (or nodal rule).
• The principle of conservation of electric charge implies that:
• At any node (junction) in an electrical circuit, the sum of currents flowing into that node is equal to the sum of currents flowing out of that node, or:Thealgebraic sum of currents in a network of conductors meeting at a point is zero.Recalling that current is a signed (positive or negative) quantity reflecting direction towards or away from a node, this principle can be stated as:
![Page 24: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/24.jpg)
Cont..
• n is the total number of branches with currents flowing towards or away from the node.
• The law is based on the conservation of charge whereby the charge (measured in coulombs) is the product of the current (in amperes) and the time (in seconds).
![Page 25: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/25.jpg)
Cont..
The current entering any junction is equal to the current leaving that junction. i2 + i3 = i1 + i4
Page No: 1.16 from Elements of Electrical Engineering ( J.N.Swamy)
![Page 26: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/26.jpg)
Kirchoff’s voltage law• This law is also called Kirchhoff's second
law, Kirchhoff's loop (or mesh) rule, and Kirchhoff's second rule.
• The principle of conservation of energy implies that
• The directed sum of the electrical potential differences (voltage) around any closed network is zero, or:More simply, the sum of the emfs in any closed loop is equivalent to the sum of the potential drops in that loop, or:The algebraic sum of the products of the resistances of the conductors and the currents in them in a closed loop is equal to the total emf available in that loop.Similarly to KCL, it can be stated as:
![Page 27: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/27.jpg)
Cont..
The sum of all the voltages around the loop is equal to zero. v1+ v2 + v3 - v4 = 0
Page No: 1.17 from Elements of Electrical Engineering ( J.N.Swamy)
![Page 28: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/28.jpg)
Cont..• Here, n is the total number of voltages
measured. The voltages may also be complex:
• This law is based on the conservation of energy whereby voltage is defined as the energy per unit charge. The total amount of energy gained per unit charge must equal the amount of energy lost per unit charge, as energy and charge are both conserved.
![Page 29: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/29.jpg)
Nodal Analysis
• Circuit Nodes and Loops:-
• Node:- A node is a point where two or more circuit elements are connected.
• Loop:- A loop is formed by tracing a closed path in a circuit through selected basic circuit elements without passing through any intermediate node more than once
![Page 30: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/30.jpg)
Example: Find the Nodes
+
-Vs
node
Page No: 2.35 self making from Circuits and Networks (U.A.Patel)
![Page 31: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/31.jpg)
Example: Find the loops
loop
Page No: 2.35 self making from Circuits and Networks (U.A.Patel)
![Page 32: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/32.jpg)
Equivalent Circuits:-
Source Transformation
Vs
+
-
Rs
Is Rs
sss IRV s
s
sR
VI
Page No: 2.61 self making from Circuits and Networks (U.A.Patel)
![Page 33: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/33.jpg)
Methods of Analysis• Introduction
• Nodal analysis
• Nodal analysis with voltage source
• Mesh analysis
• Mesh analysis with current source
• Nodal and mesh analyses by inspection
• Nodal versus mesh analysis
![Page 34: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/34.jpg)
Steps of Nodal Analysis
1. Choose a reference (ground) node.
2. Assign node voltages to the other nodes.
3. Apply KCL to each node other than the reference node; express currents in terms of node voltages.
4. Solve the resulting system of linear equations for the nodal voltages.
![Page 35: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/35.jpg)
Common symbols for indicating a reference node, (a) common ground, (b) ground, (c) chassis.
self making from Circuits and Networks (U.A.Patel)
![Page 36: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/36.jpg)
1. Reference Node
The reference node is called the ground node where V = 0
+
–
V 500W
500W
1kW
500W
500WI1 I2
Page No: 2.53 self making from Circuits and Networks (U.A.Patel)
![Page 37: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/37.jpg)
Steps of Nodal Analysis
1. Choose a reference (ground) node.
2. Assign node voltages to the other nodes.
3. Apply KCL to each node other than the reference node; express currents in terms of node voltages.
4. Solve the resulting system of linear equations for the nodal voltages.
![Page 38: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/38.jpg)
2. Node Voltages
V1, V2, and V3 are unknowns for which we solve using KCL
500W
500W
1kW
500W
500WI1 I2
1 2 3
V1 V2 V3
Page No: 2.37 self making from Circuits and Networks (U.A.Patel)
![Page 39: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/39.jpg)
Steps of Nodal Analysis1. Choose a reference (ground) node.
2. Assign node voltages to the other nodes.
3. Apply KCL to each node other than the reference node; express currents in terms of node voltages.
4. Solve the resulting system of linear equations for the nodal voltages.
![Page 40: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/40.jpg)
3. Mesh Analysis
• Mesh analysis: another procedure for analyzing circuits, applicable to planar circuit.
• A Mesh is a loop which does not contain any other loops within it
![Page 41: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/41.jpg)
(a) A Planar circuit with crossing branches,(b) The same circuit redrawn with no crossing branches.
self making from Circuits and Networks (U.A.Patel)
![Page 42: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/42.jpg)
• Steps to Determine Mesh Currents:
1. Assign mesh currents i1, i2, .., in to the n meshes.
2. Apply KVL to each of the n meshes. Use Ohm’s law to express the voltages in terms of the mesh currents.
3. Solve the resulting n simultaneous equations to get the mesh currents.
![Page 43: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/43.jpg)
Figure:A circuit with two meshes.
Page No: 1.53 from Circuits and Networks (U.A.Patel)
![Page 44: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/44.jpg)
• Apply KVL to each mesh. For mesh 1,
• For mesh 2,
123131
213111
)(
0)(
ViRiRR
iiRiRV
223213
123222
)(
0)(
ViRRiR
iiRViR
![Page 45: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/45.jpg)
• Solve for the mesh currents.
• Use i for a mesh current and I for a branch current. It’s evident from Fig. 3.17 that
2
1
2
1
323
331
V
V
i
i
RRR
RRR
2132211 , , iiIiIiI
![Page 46: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/46.jpg)
• Find the branch current I1, I2, and I3 using mesh analysis.
self making from Circuits and Networks (U.A.Patel)
![Page 47: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/47.jpg)
• For mesh 1,
• For mesh 2,
• We can find i1 and i2 by substitution method or Cramer’s rule. Then,
123
010)(10515
21
211
ii
iii
12
010)(1046
21
1222
ii
iiii
2132211 , , iiIiIiI
![Page 48: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/48.jpg)
• Use mesh analysis to find the current I0 in the circuit.
self making from Circuits and Networks (U.A.Patel)
![Page 49: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/49.jpg)
• Apply KVL to each mesh. For mesh 1,
• For mesh 2,126511
0)(12)(1024
321
3121
iii
iiii
02195
0)(10)(424
321
12322
iii
iiiii
![Page 50: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/50.jpg)
• For mesh 3,
• In matrix from become
we can calculus i1, i2 and i3 by Cramer’s rule, and find I0.
02
0)(4)(12)(4
, A, nodeAt
0)(4)(124
321
231321
210
23130
iii
iiiiii
iII
iiiiI
0
0
12
211
2195
6511
3
2
1
i
i
i
![Page 51: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/51.jpg)
Mesh Analysis with Current Sources
A circuit with a current source.
Page no. 2.36 self making from Circuits and Networks (U.A.Patel)
![Page 52: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/52.jpg)
• Case 1
– Current source exist only in one mesh
– One mesh variable is reduced
• Case 2
– Current source exists between two meshes, a super-mesh is obtained.
A21 i
![Page 53: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/53.jpg)
References-Images• https://www.google.co.in/url?sa=i&rct=j&q=&esr
c=s&source=images&cd=&cad=rja&uact=8&ved=0CAcQjRw&url=http%3A%2F%2Fwww.school-for-champions.com%2Fscience%2Fdc_circuits.htm&ei=K4ubVJ6gDpOTuATJpoLQCQ&bvm=bv.82001339,d.c2E&psig=AFQjCNEl_SrgsiAyIRg9HZYUFPPp6lHOjA&ust=1419566195856245
• https://www.google.co.in/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=0CAcQjRw&url=http%3A%2F%2Fcommons.wikimedia.org%2Fwiki%2FFile%3AOhm%27s_Law_with_Voltage_source.svg&ei=YYybVM27BsWyuATjoYLICg&bvm=bv.82001339,d.c2E&psig=AFQjCNGq9pnRDWqj5g2bi8jMXldu5gBR1g&ust=1419566530224368
![Page 54: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/54.jpg)
• https://www.google.co.in/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=0CAcQjRw&url=http%3A%2F%2Fwww.electrical4u.com%2Fideal-dependent-independent-voltage-current-source%2F&ei=WpmbVKD9CdS3uQSbjoHwBA&bvm=bv.82001339,d.c2E&psig=AFQjCNFqF_8padWMdp9hmHqIvJNWKC8n0Q&ust=1419569841612381
• https://www.google.co.in/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=0CAcQjRw&url=http%3A%2F%2Fen.wikipedia.org%2Fwiki%2FAmplifier&ei=epqbVNTFG8vbuQTyyoLACQ&bvm=bv.82001339,d.c2E&psig=AFQjCNGDRHyPWYdX7hQ85ZyeWd9na7LJww&ust=1419570102290642
![Page 55: Diploma i boee u 2 dc circuit analysis](https://reader034.vdocuments.net/reader034/viewer/2022042817/55a6a62c1a28abd02e8b46c1/html5/thumbnails/55.jpg)
REFERENCE
• B.L.Theraja, “Electrical Technology Vol.1”, S.ChandPublication.
• D.P.Kothari, “Basic Electrical Engineering”, Tata McGraw-Hill publication.
• U.A.Patel “Circuits and Networks”.