![Page 1: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/1.jpg)
ECE 002Dr. Ahmadi
Department of Electrical and Computer Engineering
The George Washington University
![Page 2: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/2.jpg)
![Page 3: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/3.jpg)
Communication SystemCommunication systems send information
electronically over communication channelsMany different types of systems which convey
many different types of informationDesign challenges include hardware, system,
andnetwork issues
Communication systems recreate transmittedinformation at receiver with high fidelity
![Page 4: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/4.jpg)
Communication System
Source encoder converts message into message signal or bits.
Transmitter converts message signal or bits into format appropriate for channel transmission (analog/digital signal).
Channel introduces distortion, noise, and interference.
Receiver processes received signal back to message signal.
Source decoder decodes message signal back into original message.
SourceEncoder Transmitt
er
SignalChannel Receiver
SourceDecoder
![Page 5: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/5.jpg)
Amplitude Modulation(AM)Modulation:
The process of converting a signal so that it can be successfully sent through a medium.
The addition of the original signal to a carrier signal
Types of Modulation:Analog Modulation – AM,FM, etcDigital Modulation
History: 1900s AM invented and popularized by De Forest; commercial radio station begins broadcasting in Pittsburgh 1920.
![Page 6: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/6.jpg)
Amplitude Modulation(AM)AM works by varying the amplitude of the
transmitted signal in relation to the information being sent. For example, changes in the signal amplitude can be used to reflect the sounds to be reproduced by a speaker
Audio signal - fa Carrier signal - fc
![Page 7: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/7.jpg)
![Page 8: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/8.jpg)
Receiver: AM Radio KitModel: AM-780 A standard AM radio frequency receiverRadio frequency (RF): 3kHz – 300GHzAM Broadcast Frequencies : 535kHz –
1605kHz
![Page 9: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/9.jpg)
![Page 10: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/10.jpg)
AM Radio: 535kHz – 1605kHz
FM Radio: 88MHz – 108MHz
![Page 11: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/11.jpg)
AM-780 Block Diagram
Component List: Printed Circuit Board(PCB)
(mechanically support and electrically connect electronic components) LC Circuit: Inductors and Capacitors.
(Selects the input signals by different frequencies) IC 484: Transistor.
(Amplifies the selected input signal) Peak Detector: Two diodes.
(Detects the peak of the amplified input signal) IC LM-386 chip: Power amplifier
Specifications: http://www.national.com/mpf/LM/LM386.html#Overview
Antenna, Speaker, Resistors/Potentiometers and Wires
Antenna LC Circuit
Transistor(IC 484)
Diodes IC LM 386 Chip
![Page 12: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/12.jpg)
Circuit BoardPrinted Circuit Board
![Page 13: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/13.jpg)
ResistorsUse bands to tell resistors apart and to find
value
![Page 14: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/14.jpg)
CapacitorAn electronic component that has ability to
store a charge and block DC current.
![Page 15: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/15.jpg)
Semiconductors
DiodesIntegrated Circuits IC 386
Transistor 484
![Page 16: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/16.jpg)
Other Parts
![Page 17: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/17.jpg)
![Page 18: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/18.jpg)
Soldering Safety Precautions :Never touch the element or tip of the soldering iron.
They are very hot (about 400°C) and will give you a nasty burn.
Take great care to avoid touching the mains flex with the tip of the iron. The iron should have a heatproof flex for extra protection. An ordinary plastic flex will melt immediately if touched by a hot iron and there is a serious risk of burns and electric shock.
Always return the soldering iron to its stand when not in use. Never put it down on your workbench, even for a moment!
Work in a well-ventilated area. The smoke formed as you melt solder is mostly from the flux and quite irritating. Avoid breathing it by keeping you head to the side of, not above, your work.
Wash your hands after using solder. Solder contains lead which is a poisonous metal.
![Page 19: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/19.jpg)
Preparing the soldering iron: Place the soldering iron in its stand and plug in.
The iron will take a few minutes to reach its operating temperature of about 400°C.
Dampen the sponge in the stand. The best way to do this is to lift it out the stand and hold it under a cold tap for a moment, then squeeze to remove excess water. It should be damp, not dripping wet.
Wait a few minutes for the soldering iron to warm up. You can check if it is ready by trying to melt a little solder on the tip.
Wipe the tip of the iron on the damp sponge. This will clean the tip.
Melt a little solder on the tip of the iron. This is called 'tinning' and it will help the heat to flow from the iron's tip to the joint. It only needs to be done when you plug in the iron, and occasionally while soldering if you need to wipe the tip clean on the sponge.
![Page 20: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/20.jpg)
Preparing the soldering iron:
![Page 21: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/21.jpg)
Start soldering: Hold the soldering iron like a pen, near the base of the handle.
Imagine you are going to write your name! Remember to never touch the hot element or tip.
Touch the soldering iron onto the joint to be made. Make sure it touches both the component lead and the track. Hold the tip there for a few seconds and...
Feed a little solder onto the joint. It should flow smoothly onto the lead and track to form a volcano shape as shown in the diagram. Apply the solder to the joint, not the iron.
Remove the solder, then the iron, while keeping the joint still. Allow the joint a few seconds to cool before you move the circuit board.
Inspect the joint closely. It should look shiny and have a 'volcano' shape. If not, you will need to reheat it and feed in a little more solder. This time ensure that both the lead and track are heated fully before applying solder.
![Page 22: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/22.jpg)
Start soldering:
Resistor 1
![Page 23: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/23.jpg)
Start soldering:
![Page 24: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/24.jpg)
Soldering Tips: Ensure that items to be soldered are perfectly clean. This can be achieved
with wire wood or fine emery cloth. Just because a piece of metal looks bright and clean it may not be.
Make a good mechanical connection by wrapping wires around each other or around a terminal.
When applying heat, do not apply it to the solder. Heat the base material, e.g. wires so they become sufficiently hot to melt the solder and flow it into the joint. A small amount of fresh solder on the tip when you begin soldering will help to carry heat from the iron to the joint.
When solder has been applied to a joint smoothly slide the iron away to leave the joint neat.
Avoid moving joint or wire after removing iron. Blowing on the joint will speed cooling.
On electrical and electronic components avoid too much heat. A heat sink can be used to dissipate heat away from the component.
Do not apply more solder than needed. Excess solder can cause short circuits. It is advisable to pre tin components before soldering, especially stranded
wire. Twist the strands together, then heat and saturate with solder. Sweating a joint is easy after tinning. Just twist wires together and apply heat. To desolder a joint apply heat and use a soldering aid like solder wick to
remove solder and separate joint. Be sure to use new solder when re-soldering.
Fumes from some fluxes can be unpleasant so be sure there is good ventilation in the work area.
Do not use a file to clean soldering tip, wiping on a wet sponge when tip is hot should keep tip clean.
![Page 25: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/25.jpg)
Soldering Tips:
![Page 26: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/26.jpg)
![Page 27: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/27.jpg)
Schematic Diagram AM-780K
![Page 28: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/28.jpg)
Assemble Components to the PCB
![Page 29: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/29.jpg)
Assemble Components to the PCB
![Page 30: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/30.jpg)
Assemble Components to the PCB
![Page 31: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/31.jpg)
Assemble Components to the PCB
![Page 32: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/32.jpg)
Assemble Components to the PCB
![Page 33: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/33.jpg)
Install Battery Holder
![Page 34: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/34.jpg)
Install Antenna
![Page 35: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/35.jpg)
Alignment
![Page 36: ECE 002 Dr. Ahmadi Department of Electrical and Computer Engineering The George Washington University](https://reader038.vdocuments.net/reader038/viewer/2022103022/56649cad5503460f9497039e/html5/thumbnails/36.jpg)