Download - En NewUI Short V3.1G
-
User Manual for Embedded DVR
-
User Manual for Embedded DVR
- 1 -
Notes:
The power supply of this DVR is provided through DC12V adapter, please check the
power output before installation and ensure it can meet the requirements;
Do not place the DVR at a place subject to rain and moisture;
Do not install the DVR at a place subject to violent vibration;
Do not install the DVR at a place subject to direct sunlight, and be far away from high
temperature environment;
The DVR should be installed in a space without much dust, and the environment
should be kept clean and tidy;
The DVRs back panel should be placed 15cm or more away from other objects or
wall for cooling;
The DVR should work under temperature, humidity and voltage according to its
technical specifications;
The space where DVR is installed should not be stored with corrosive chemicals that
may produce volatile gases to avoid affecting the DVRs life;
Proper grounding should be guaranteed during operation;
The DVR shall be installed to ensure proper connection with other devices.
Please buy HDD from official channel to meet DVRs long time and large data reading
and writing requirements.
Statement:
This manual only introduces basic operation.
Products are subject to the real products and this manual is just for reference.
Products update without further notice. Nuances of partial functions are permitted
before and after updating.
Please contact the Customer Service Department for the latest program and
supplementary instruction files.
This manual is applicable to various models, and the specific operation of each
product is not listed here. Users can operate the DVR based on this manual for the
actual products.
We have tried our best to ensure the completeness and accuracy of this manual.
However, due to the unstable environment and other reasons, the real value of some
data may differ. If any problem or dispute arises, the companys final explanation will
prevail.
If carrying out operation not according to the instruction of this manual, the user
shall bear the losses sustained.
-
User Manual for Embedded DVR
- 2 -
Introduction
DVR Introduction
This DVR adopts high performance video processing chips and embedded Linux system. It
utilizes many most advanced technologies, such as standard H.264 with low bit rate, Dual
stream, SATA interface, VGA output mouse supported, IE browser supported with full
remote control, mobile view(by phones), etc. it has very powerful functions and high
stability. It can be widely used in bank, telecommunication, transportation, factories,
warehouse, irrigation, etc.
Main Features
Standard H.264 compression
Simultaneous multi-output ,VGA ,CVBS and HDMI(optional)
Support channel privacy mask and motion detection
Alarm schedule
Multi channels playback
USB mouse and IR remote control included
USB backup with AVI format
Multi PTZ dome control
Free DDNS services supported
Free Cloud platform service for Internet view
Support network access via browsers, PC client ,CMS , smart phone,etc
Support 3G USB modem to access the Internet
-
User Manual for Embedded DVR
- 3 -
Chapter 1 Open Case And Installation
1.1 Open case inspection
1.1.1 Notes
After receiving the products, please check if the DVR is complete and make sure if there
is any accidental damage during transportation.
Open the package and check if the accessories are complete, and then remove the
protective film of the DVR package.
1.1.2 Package and accessories
The Package contains the following accessories:
One IR remote control.
One pair of remote controll batteries.
One piece of Product Certificate.
One piece of User Manual.
One or more SATA HDD cables (already installed in the case)
One DC12V power adapter.
One piece of CD.
One HDD bracket (already installed) and mounting screws, etc.
NOTE: Specific model of the above accessories may differ, please refer to the list of
accessories in the package.
-
User Manual for Embedded DVR
- 4 -
1.2 Product appearance and ports
1.2.1 Front panels
-
User Manual for Embedded DVR
- 5 -
1.2.2 Keys and tags
NO. Tag Name Discription
1 MUTE Disable the sound output
2 INFO Check the device system information
3
PIP Display live images picture in picture
4 PTZ Call the PTZ camera
5 PLAY / PAUSE Compound button play and pause
6 REW Rewind
7 SEARCH Search the video file
8
REC Start or stop the manual record
9
MENU Enter the main menu
10 ESC Quit
11 USB Connect the USB decives
12
POWER Power switch button
13
DIRECTION Move the cursor to right/left/up/down
14 Enter Comfirm the change
15
IR Reciever IR remote reciever window
16
STATUS Indicate the running status
-
User Manual for Embedded DVR
- 6 -
1.2.3 Rear panel and ports
Note: the real production maybe have some difference with this panels below.
-
User Manual for Embedded DVR
- 7 -
1.2.3 Ports descriptions
NO. Name Discription
1 VIDEO IN BNC connectors for analog video input
2 VIDEO OUT BNC connector for analog video output
3 AUDIO IN RCA connectors for analog audio input
4 AUDIO OUT RCA connector for analog audio output
5 VGA DB15 for VGA monitor
6 HD-port To connect the HDMI high definition monitor(optional)
7 NETWORK RJ-45 connector for Ethernet
8 RS485 To control the PTZ camera(A > +,B > -,G > Ground)
9 DC 12V DC 12V power supply
10 ALARM Alarm output(On-off switch output)
11 SENSOR Alarm input(On-off switch input)
12
Ground
Note:
1, RS485 A should connect to PTZ data+, B to data-;
2, Recommend connecting the DVR housing to ground (PE cable).
-
User Manual for Embedded DVR
- 8 -
1.3 IR remote control
The DVR can be controlled with the IR remote control. Ensure the batteries are installed
before using.
NO. Name Discription
1 POWER OFF Shutdown the DVR
2 ESC Quit the menu
3 FAST REWIND Change the rewind speed
4 SETP Playback frame by frame
5 PIP Show video picture in picture
6 RECORD Start/stop manual record
7 MUTE Disable the sound
8 NUMBER Switch the channel
9 MENU Enter to the menu
10 ENTER Comfirm an item
11 FAST FORWARD Change the forward speed
12 PLAY / PAUSE Play and pause when playback
13 PTZ Move the PTZ camera
14 SEARCH Playback the video
15 ZOOM Enlarge the channel image
-
User Manual for Embedded DVR
- 9 -
1.4 Hardware installation
1.4.1 HDD installation
(1)Open the cover of the DVR, fix the HDD into the bracket;.
(2)Connect the HDD data and power cables to the HDD;
(3)Tighten the screws to fix the HDD in the case;
(4)Lock the cover with crews.
Note: Do not plug in or out the HDD when the DVR powered on.
1.4.2 Connection to the camera and monitor
Connecting the signal of camera with a BNC cable to the DVR video input, connect the
signal of DVR video output with a BNC cable to the monitor (Please refer to the back panel
figure). Connect the RS485A (+) and the B (-) respectively to corresponding DVR interface
with wires, if camera is the PTZ which can be controlled.
Note: Please refer to the electric topology in the last page to connect the devices.
-
User Manual for Embedded DVR
- 10 -
Chapter 2 Getting Started
2.1 Power on and off
Note:
Ensure that the power supply can meet the requirement of the voltage and rated
power. Make sure the monitor is powered on and connected to the DVR.
Power on
1. Connect the power supply plug to the outlet;
2. Conenct the DC 12V output plug to DVR;
3. Switch on the Power button (if available)
Power off
Note:
Strongly recommend click the Shut Down in the Main Menu before switch off the
DVR.
1. Click the Shut Down icon in the Main Menu;
2. Switch off the Power button;
3. Plug out the DC 12V plug and the AC plug.
2.2 Using the Setup Wizard
When you turn on the DVR, the system shows the boot logo and BIOS message, and then
enters to Setup Wizard window by default.
Note:
If the check box is unselected the Setup Wizard will not show next time. Otherwise ,it
will pop up every time restarting the DVR.
-
User Manual for Embedded DVR
- 11 -
1. This step you can configure the basic parameters, such as, device name, language date
time ,etc.
2. If the DVR will connect to the Internert via a router, the network parameters should
be configured.
3. In the last setp, you should format the HDD if you want save the video files.
After finished all the setps above, the DVR will start recording in normal.
--- end.
Chapter 3 Live View
In this figure you can see the channel name and timestamp. Also you can see the record
status green for timer record ,yellow for motion detection, blue for manal record and red
for alarm record. The small speaker means the sound output is enabled for this channel.
Note:
By default, the DVR enable the motion detection and manual record , you can click
the REC button on the live view bar(see 3.2) to stop the manual record
-
User Manual for Embedded DVR
- 12 -
3.1 Login window
When you quit or power on with unselected the Setup Wizard check box , the login
window will show above. Click the input field the virtual key board will pop up.
Note:
User Name: admin
Password: 00000000
3.2 Live control bar
In the live view screen, you can see a control bar showing on the screen.
Main menu: click and enter to the Main Menu;
Split mode: to split the screen to different display mode;
PIP: display picture in picture;
Sequence patrol: enable multi-camera auto sequence in Live View mode;
Digital zoom: enlarge the image in single channel;
Sound: adjust or disable the audio output;
PTZ: move the PTZ dome camera;
Capture: make a channel screenshot and save to HDD;
REC: start / stop recording manually;
Quicklly review: start a playback of the last five minutes.
Chapter 4 Main Menu
The Main Menu contain all the function for the DVR configuration parameters. If you login
as administrator you can have the full control permission.
-
User Manual for Embedded DVR
- 13 -
Chapter 5 Record Search And Backup
Select the date and click the Search button, the list will show the blue or red if there are
video fils in the HDD.
Select the start time and click button to start playback.
The DVR support channel capture and store in the HDD. You can view the image directly.
You can set the start time and end time to backup. Click the Start button to stat the
backup.
Main Functions
Sub Functions Lists Function Details
1. Setup
2. Backup&Playback
3. Maintenance 4. Record Schedule 5. Alarm Schedule 6. Advanced Settings 7. System Info
-
User Manual for Embedded DVR
- 14 -
Capture 6 Working on the Internet
6.1 Remote view via IE browser
6.1.1 IE Active-X control download and installation
6.1.2 Login window
1. After installing, you can see a login window showing as below:
User name: admin
Password: 00000000
NOTE:
The ID/IP can be MAC address,Domain or the IP
address. Check the network for the IP address and MAC
address.
6.1.3 Live view
The live view window will pop up after successful login. You can configure the parameters
at the right click menu of the device name.
Enter the URL:
http://121.199.46.114
/
Click install
-
User Manual for Embedded DVR
- 15 -
6.1.5 Remote playback and download
Click the Playback button then click the Search button you can playback the record files via
remote computer.
Click the Video clip to set the beginning time and click it again to finish the video clip. The
file will save at D:\CMS Files\Video\Remote Playback Record\ by default.
6.2 CMS management
This series DVR supports the CMS software and can be managed intensively.
6.2.1 CMS installation
You can find the CMS in the accessary CD. Double click the install program to install it to
your computer.
6.2.2 First running
At the first running you need make an account:
Click the OK to make the account and login into the live view window.
Right click the device list and select add area to add a region. Right click the region again
you can add more regions and devices.
Download Video clip
-
User Manual for Embedded DVR
- 16 -
6.2.3 CMS Cloud function
You can add the DVR by IP or by ID. The MAC address can be used as Device ID. The Device
IP can use the routers public IP address or DVRs private IP address.
Note :
How to use the Cloud sercive ?
Setp 1. Connect the DVR to network and power on the DVR;
Setp 2. Write down the MAC address in network icon and check the Cloud status;
Step 3. Install the CMS software from the CD and right click to add device;
Step 4. Change the login type to by ID,and input the wrote down MAC address;
Step 5. Click OK to add this device.
----End
6.2.4 Live view
After adding the DVR, you can see the camera Icon become blue. Drag or double click the
camera you can open the view.
Device ID
-
User Manual for Embedded DVR
- 17 -
6.2.5 Remote playback
Click the second Icon on the top you can see the playback window showing as below:
Click the search button and click the play button you can see the playback by remote CMS.
Also you can click the cut and download the video fils.
Note:
The file will save at D:\CMS Files\Video\Remote Playback Record\ by default.
6.2.6 Electrolic Map
The CMS support powerfull electrolic map function. This function make the video s
urveillance more easy and the camera control become more convenient.
Click the icon you can enter to the E-map function interface . you can see th
e Google Map show in the center . you can operate the google map like the goo
gle website.
The E-map function have two layers of maps. The one is google map and the other one is
the building ichnography. The building ichnography is used to put the cameras in.
How to use the E-map function?
Step 1. Add the picture of the building ichnography under the google map at the right
side of the window;
Step 2. Find out the DVR address in the google map
Step 3. Right click on the google map and select the Add hot area to add a loc
ation mark. You can see a sign on the map;
search Video list
play download
-
User Manual for Embedded DVR
- 18 -
Step 4. Click the location mark and drag the camera to the to the building ichnography.
You can move the camera icon to the place you want. Double click the camera icom you
can view the live video the the channel.
----End
When the channel catch an ALARM event the E-map will pop up the live video to alert the
user.
6.3 Mobile phone view
The DVR supports the IOS and Andriod smartphone to login and monitoring. The APP video
defence can download from the APPStore and Google play. It can support multi-channel
live view and playback functions.
More details you can get from the CD.
-
User Manual for Embedded DVR
- 19 -
Appendix: System topology
-
User Manual for Embedded DVR
- 20 -