®
filtration technologies
FTP SERIES CARTRIDGEFILTERS(GRP FILTERHOUSING)
The permanentfiltering solution
2 filtration technologies
ftp series cartridge filters (grp)
■ Perfect corrosion resistance behaviour.■ Reduced maintenance during its life span.■ Excellent quality/price ratio, above all in
filters for treating large flows.■ High resistance when treating waters
with a high degree of salinity.■ Versatility in design for different pressures.
Advantages
Standard materials
IntroductionFluytec GRP (Glass Fibre Reinforced Polyester) cartridge filters provide optimal behaviour with water of various degrees of salinity, reducing the maintenance needed in these conditions and optimizing the installation cost of filtering equipment.
General review of Double Flange Filter.
The bodies of these filters are designed according to the Ad-Merkblatt design code from pressure vessels and are made according to the 97/23 CE S. S.3.3 European Standard for Pressure Filters.
The standard pressure is 6 bar and it is possible to design equipment for different nominal pressures to order.
The internal parts in contact with the water are of various plastics and, when of metal, are suitably plasticised. The seals are O-rings and are designed for easy replacement and maintenance.
The bodies have a natural internal finish while externally they are covered with a twin component paint and finished with a top coat of paint.
All the main connections for the fluid inlet and outlet and the vent and drain are designed with flanges.
The equipment is anchored at the base with Carbon Steel legs, each with a hole for anchoring studs, not supplied by the manufacturer.
General description
View of top opening of Double Flange Filter.
Body: GRP
FF plate: GRP / PVC
Legs: Coated CS *
External bolts: AISI 304*
Internal parts: PVC
O-ring: EPDM*
*Other materials available.
3filtration technologies
ftp series cartridge filters (grp)
4 filtration technologies
ftp series cartridge filters (grp)
Traditional double flange type cartridge filters with 40 to 100 cartridges.
These filters have inlet and outlet connections on the side of the body consisting of two flanges, an upper one, also called the closure, and a low one at the bottom, on which the cartridges are housed.
1. FTP Medium Flow series
Cartridge installation
■ Possibility of equipping with a lifting arm.
Options
The bottom of the cartridge is located on the guide pipe, the base of which has a perimeter flange to seal the bottom end of the cartridge - Figure 1 -. The top is closed with a part exclusively designed and manufactured by Fluytec called “teat” which is pressed against the
cartridge by the spring between it and the top and/or filter lid - Figures 2 and 3 -.
This system ensures the perfect sealing of the cartridge, making it impossible for the fluid to pass through any place other than the filtering medium (the end purpose of the filter) - Figure 4 -.
Model ADN B C H L N1/N2
DNQdesignm3/hour
No. cartridges
L cartridges
80 FTP-4 FL 750 485 1,365 2,140 595 200 208 80 1,000
80 FTP-5 FL 750 485 1,490 2,390 595 200 260 80 1,250
90 FTP-4 FL 800 500 1,405 2,175 625 200 234 90 1,000
90 FTP-5 FL 800 500 1,530 2,425 675 250 292 90 1,250
• Measurements in mm.
• Measurements for a design pressure of 6 bar. Other measurements/flows to order.
• Design flows calculated for a flow rate of 0.65 m³/h for every 10” of cartridge.
Virgen del Milagro desalination plant, Mazarrón (Murcia).
2
4
1
3
AL
H
B
C
5filtration technologies
ftp series cartridge filters (grp)
Traditional double flange type cartridge filters with 120 to 400 cartridges.
These filters have inlet and outlet connections on the side of the body consisting of two flanges, an upper one, also called the closure, and a low one at the bottom, on which the cartridges are housed.
2. FTP HighFlow series: double flange
■ Possibility of equipping with a lifting arm.■ Possibility of equipping with inlet and
outlet elbows.
Options
Cartridge installationThe bottom of the cartridge is located on the guide pipe, the base of which has a perimeter flange to seal the bottom end of the cartridge - Figure 1 -. The top is closed with a part exclusively designed and manufactured by Fluytec called “teat” which is pressed against the
cartridge by the spring between it and the top and/or filter lid - Figures 2 and 3 -.
This system ensures the perfect sealing of the cartridge, making it impossible for the fluid to pass through any place other than the filtering medium (the end purpose of the filter) - Figure 4 -.
2
4
1
3
Installation in Abrera, Barcelona.
Model ADN B C H L N1/N2
DNQdesignm3/hour
No. cartridges
L cartridges
100 FTP-4 FL 850 750 1,850 2,650 690 250 260 100 1,000
100 FTP-5 FL 850 750 1,975 2,900 690 250 325 100 1,000
120 FTP-4 FL 925 750 1,870 2,680 670 250 312 120 1,000
120 FTP-5 FL 925 750 1,995 2,930 670 250 390 120 1,250
135 FTP-4 FL 950 750 1,880 2,700 750 250 351 135 1,000
135 FTP-5 FL 950 750 2,005 2,950 750 250 438 135 1,250
150 FTP-4 FL 1,000 750 1,910 2,760 780 250 390 150 1,000
150 FTP-5 FL 1,000 750 2,035 3,010 780 250 487 150 1,250
180 FTP-4 FL 1,100 750 1,945 2,820 820 250 468 180 1,000
180 FTP-5 FL 1,100 875 2,235 3,230 820 300 585 180 1,250
215 FTP-4 FL 1,200 875 2,135 3,030 920 300 559 215 1,000
215 FTP-5 FL 1,200 950 2,335 3,350 920 350 698 215 1,250
240 FTP-4 FL 1,300 950 2,215 3,130 970 350 624 240 1,000
240 FTP-5 FL 1,300 950 2,340 3,380 970 350 780 240 1,250
280 FTP-4 FL 1,400 950 2,245 3,185 1,020 350 728 280 1,000
280 FTP-5 FL 1,400 1,050 2,470 3,535 1,020 400 910 280 1,250
330 FTP-4 FL 1,500 1,050 2,375 3,345 1,075 400 858 330 1,000
330 FTP-5 FL 1,500 1,050 2,500 3,595 1,075 400 1,072 330 1,250
360 FTP-4 FL 1,600 1,050 2,405 3,400 1,125 400 936 360 1,000
360 FTP-5 FL 1,600 1,050 2,530 3,650 1,125 400 1,170 360 1,250
• Measurements in mm.
• Measurements for a design pressure of 6 bar. Other measurements/flows to order.
• Design flows calculated for a flow rate of 0.65 m³/h for every 10” of cartridge.
AL
H
B
C
6 filtration technologies
ftp series cartridge filters (grp)
Cartridge filters with sword system and single flange for high flows.
Filters consisting of a body with a single flange in which the inlet connection is at the bottom while the outlet is in the top lid of the filter.
The false bottom plate on the flange is the support from which the swords hang.
3. FTP HighFlow series:swords system
The filter cartridges are mounted on swords, supports with their heads screwed into the false bottom plate and with a nut threaded onto their tops to seal the cartridge - Figure 1 -.
The lower plastic grille gives the filter pack the necessary rigidity to prevent the
cartridges from breaking due to internal vibration - Figure 2 -. With an additional false bottom plate and set of swords, a filter pack can be prepared on site while the other is operating, thus reducing the equipment’s downtime - Figure 3 - .
Cartridge installation
Installation in Águilas, Murcia.
■ Replacement of complete filter pack.■ Optimizing of filtering cross section.■ Economical manufacture.■ Possibility of equipping with inlet and
outlet elbows.
Advantages
21
3
Replacement of filter pack.
Model ADN
B H N1/N2DN
Qdesignm3/hour
No.cartridges
L cartridges
120 FTP-4 B 900 750 3,040 250 312 120 1,000
120 FTP-5 B 900 750 3,285 250 390 120 1,250
120 FTP-7 B 900 875 3,960 300 546 120 1,750
150 FTP-4 B 1,000 750 3,095 250 390 150 1,000
150 FTP-5 B 1,000 750 3,345 250 487 150 1,250
150 FTP-7 B 1,000 875 4,020 300 682 150 1,750
180 FTP-4 B 1,100 750 3,140 250 468 180 1,000
180 FTP-5 B 1,100 875 3,615 300 585 180 1,250
180 FTP-7 B 1,100 950 4,140 350 819 180 1,750
240 FTP-4 B 1,200 875 3,410 300 624 240 1,000
240 FTP-5 B 1,200 950 3,735 350 780 240 1,250
240 FTP-7 B 1,200 1,050 4,285 400 1,092 240 1,750
270 FTP-4 B 1,300 875 3,435 300 702 270 1,000
270 FTP-5 B 1,300 950 3,760 350 877 270 1,250
270 FTP-7 B 1,300 1,050 4,310 400 1,228 270 1,750
310 FTP-4 B 1,400 950 3,565 350 806 310 1,000
310 FTP-5 B 1,400 1,050 3,910 400 1,007 310 1,250
310 FTP-7 B 1,400 1,150 4,465 450 1,410 310 1,750
360 FTP-4 B 1,500 950 3,615 350 936 360 1,000
360 FTP-5 B 1,500 1,050 3,965 400 1,170 360 1,250
360 FTP-7 B 1,500 1,300 4,665 500 1,638 360 1,750
400 FTP-4 B 1,600 1,050 3,765 400 1,040 400 1,000
400 FTP-5 B 1,600 1,150 4,115 450 1,300 400 1,250
400 FTP-7 B 1,600 1,300 4,715 500 1,820 400 1,750
• Measurements in mm.
• Measurements for design pressure of 6 bar; other measurements/flows to order.
A
H
B
7filtration technologies
Project Country Capacity m3/day
Shuqaiq II IWPP Saudi Arabia 240,000
ETAP Abrera Spain 220,000
Rabigh IWPP Saudi Arabia 220,000
Al Dur Bahrain 214,000
UDEM Ténès Algeria 200,000
Águilas Guadalentín Spain 200,000
Hamma SWRO Algeria 200,000
Sant Joan Despí Spain 190,000
Perth II SWRO, phase 1 Australia 153,000
Barka II SWRO Oman 153,000
Perth II SWRO, phase 2 Australia 153,000
Trinidad and Tobago SWRO Trinidad and Tobago 130,000
Bahía de Palma SWRO Spain 68,000
WTP for Steel Plant Turkey 65,000
Aruba SWRO Netherlands Antilles 57,120
Tía Juana Venezuela 48,000
Harley SWRO USA 40,000
Ouargla BWRO Algeria 40,000
Sta. Bárbara IDAM Curaçao 25,000
Marsa Matrouth SWRO Egypt 24,000
Copiapó SWRO Chile 18,000
Mossel Bay SWRO South Africa 15,000
ftp series cartridge filters (grp)
Fluytec filters process 12,000,000 m3 per day in installations worldwide, making it the leader in the national market and with an increasing international presence.
The following table shows some references for Fluytec projects, reflecting its worldwide presence.
Fluytec references
Fluytec installations in various parts of the world.
Camino de Sakoni, 18 • 48950 Erandio - Vizcaya (Spain) • T: (+34) 94 467 61 50 • F: (+34) 94 467 61 [email protected] • www.fluytec.com
Sub
ject
to c
hang
e w
ithou
t not
ice.
See our Website for other design criteria
Fluytec solutions worldwide
■ FTI series cartridge filters (SS, CS)■ FTPV series cartridge filters (PVC)■ …
Other products in this range:
v.4