First results of BBA testsat FERMI @ Elettra (Trieste)
and
Update from ATF2
Andrea Latina for the CLIC Beam Physics team
Inputs on ATF2 from Juergen Pfingstner and Marcin Patecki
CLIC Project Meeting – June 13, 2014
2
Introduction / Disclaimer
• We tested our BBA tools developed for FACET at Fermi, Elettra, Trieste
• Due to some bugs in the software interfacing our tools with their control system, we ended up having only three hours of effective beamtime
3
Fermi @ ElettraFree Electron Laser for Multidisciplinary Investigations
4
FERMI electron beamlines
Single-pass FEL w/ 10 Hz repetition rateLinac energy: from 100 MeV to ~1.2 GeVBunch charge: 800 pCBunch length: from 1.5 mm to 60 micron Emittance at gun: ~1.2 mm mrad
5
The Fermi control room
6
BBA setup and System IdentificationThe goal was to test our automatic steering tools:- Orbit + Dispersion + Wakefield
correction(1:1 + DFS + WFS)
BBA Setup:• 27 X correctors• 27 Y correctors• 30 BPMs
Machine:• 1.5 betatron oscillations• Effective bpm resolution = 5 - 10 micron• Single-bunch 10 Hz repetition rate• SysID time required:
– About 3 minutes to measure 1 response matrix (can be reduced to 30 seconds, with deeper integration in their control system)
Measured horizontal orbit response matrix
7
Dispersion-Free Steering
The dispersion was measured reducing the amplitude of klystron 2 to 98% of its nominal value
This operation occurs in 1 cycle @ 10 Hz
Weight for DFS = 7 (tuned for ~10 micron BPM resolution)
8
800 mm
200 mm
Dispersion measurement before DFS
9Vertical dispersion reduced by a factor ~40 ! Horizontal dispersion by factor ~4 (!)
25 mm
50 mm
Dispersion measurement after DFS
10
Emittance before BBAat the end of L4
HV
11
Emittance measurement after DFS
Horizontal emittance from 4.31 mm mrad to 3.30 mm mrad. Vertical emittance wasn’t good though: needs investigation.
12
1:1 + WFS
The wakefields were measured by changing the bunch charge to 650 pC(tests with 900 pC were foreseen, but there was not time for performing them)
Changing the charge takes about 10 seconds (time for charge feedback to converge)
Weight for WFS = 7 - 20 (tuned for ~10 micron BPM resolution)
13
1:1 + DFS + WFS
14
Emittance measurement after1:1 + DFS + WFS
HV
Emittance summary at Linac End: (H; V) (measurement error: ~±0.05 mm mrad)
Before correction: (4.31; 3.21) mm mradAfter DFS: (3.30; - ) mm mradAfter DFS+WFS: (2.75; 2.57) mm mrad (-35% in X, -20% in Y)
Ground motion correlation experiment at ATF2
Acquisition of • BPM readings
Acquisition of• GM readings• Beam arrival signal
• Goal 1: Show that the beam motion (due to ground motion) can be predicted via motion
sensors (correlation between two measurements).
• Goal 2: Correct the beam motion via a feed-forward system.
• Purpose: Such a feed-forward system could simplify and improve the ground motion
mitigation for ATF2 and for linear colliders in general.
• Experimental setup for goal 1:
J. Pfingstner & M. Patecki
16
Region with strong ground motion source
1.Water pipes under girder
(probably touching at one point)
2.Heavy objects on the girder (lead
bricks, Dipole magnet). This could
lower resonance frequency.
Q1X
Q2X
Cooling water pipes
At least two were problems identified
J. Pfingstner & M. Patecki
17
Orbit jitter reduction after detecting excitation sources
Beam jitter
• The correlation between motion sensors and BPM measurements have been up to 70%.
• Strong excitation of quadrupole motion was detected via motion sensors.
• An inspection showed that water cooling pipes and tubes were touching the girder.
• After removing the excitation, orbit jitter was reduced from 20% to 14% (half the power).
• Similar excitation detected and removed further upstream. Later measurements revealed the existence of another jitter source. This has to be
investigated.
Correlation
J. Pfingstner & M. Patecki
18
Conclusions / Future PlansI. Beam-based alignment tests• Fermi is a very good machine for tests
– Very fast control system– Excellent diagnostics
• Our tools worked very well: emittance reduced by ~35% in H and ~20% in V
• Future plans: near future– Study convergence and fully explore the space of parameters– Envisage tests of tuning bumps? on-line parasitic DFS / WFS?
II. Ground-motion correlation experiment at ATF2:• Important progress:
– One jitter source located and removed: orbit jitter was reduced from 20% to 14% (half the power)
– Correlation measurements improved as well
• Future plans:– Search for the remaining jitter sources, by putting the sensors to further locations– Start preparing for goal 2 (uncertain time scale)
III. Other tests: FACET, Wakefields in the accelerating structures, …