Download - Hoisting equipments

Transcript
Page 1: Hoisting equipments

HOISTING EQUIPMENTS

Page 2: Hoisting equipments

INTRODUCTION The hoisting is the lifting of the

material against gravity and maybe done with a wide range of equipments from the small hand operated simple screw or hydraulic-jack to modern high powered cranes and elevators.

Page 3: Hoisting equipments

The common equipments used are as follows:

Pulley and sheave block Chain hoists Mobile cranes Winch Jack Shear leg Tower cranes Whirler cranes Derrick cranes Gantry cranes

Page 4: Hoisting equipments

PULLEY AND SHEAVE BLOCK

A pulley is a wheel on an axle or shaft that is designed to support movement and change of direction of a cable or belt along its circumference. Pulleys are used in a variety of ways to lift loads, apply forces, and to transmit power. In nautical contexts, the assembly of wheel, axle, and supporting shell is referred to as a "block."

A pulley may also be called a sheave or drum and may have a groove between two flanges around its circumference. The drive element of a pulley system can be a rope, cable, belt, or chain that runs over the pulley inside the groove.

Page 5: Hoisting equipments

The pulley and sheave blocks suitable for lifting rough surface and heavy loads.

For this purpose the chains and wire ropes are used.

The alloy chains are best suited for hoisting operation.

The weakest component of this system is the load hook. The hook fails by straightening. Once the hook gets elongated or straightened, it should be replaced.

A typical sheave and pulley block is shown in fig.

Page 6: Hoisting equipments
Page 7: Hoisting equipments

CHAIN HOISTS The chain hoists are the popular

mechanism for lifting loads upto tones. The system consists of two sets of

chains, namely the hand and load chain. The hand chains are particularly useful

for the isolated location , where an electric motor or other types of mechanical equipments are not available.

The pull applied through the hand chain is transmitted to the load chain with a multiplication factor of over 20.

Page 8: Hoisting equipments

The load to be lifted is held by a load hook while another hook(called support hook) at the top, support the mechanism.

The two hooks however ,should not be interchange as the support hook is made much stronger than the load hook.

There are four types of hand operated chain hoists are in use:

( 1) Differential (2)screw geared (3) spur geared (4) pull lift

Page 9: Hoisting equipments
Page 10: Hoisting equipments

MOBILE CRANES

Mobile crane is used in big construction projects for lifting heavy loads.

It is used for loading and unloading for material in coal mines.

Loading and unloading of ships. To take the load from ground level and

place it into the trucks.

Page 11: Hoisting equipments
Page 12: Hoisting equipments
Page 13: Hoisting equipments

WINCH A winch is a mechanism in the shape of

a cylinder or drum, over which rope or chain is wound.

If a winch is used only for raising and lowering, it is sometimes referred to as hoist.

The winches are of two types :- (1) hand winches (2) power winches

Page 14: Hoisting equipments
Page 15: Hoisting equipments

TOWER CRANES

These are the crane of swing job type and are mounted on high steel towers.

The height of tower maybe 25 to 30 m and these cranes are found to be suitable in the construction of tall buildings in congested areas.

The ground area required for such cranes is very small.

Page 16: Hoisting equipments
Page 17: Hoisting equipments
Page 18: Hoisting equipments
Page 19: Hoisting equipments

WHIRLER CRANES This crane is a combination of stationary

and mobile unit. This combines the advantages of log boom of derrick crane and mobility of the mobile crane.

The rotating structure has an outer framework.

The boom is attached to the front end of this framework. The counter weight is provided at the rear end. On the diagonally opposite corners of the base, two separate motors are provided, which give movement to the central shaft.

Page 20: Hoisting equipments

DERRICK CRANES The derrick cranes are of two types,

namely: (1) Guy derrick and (2) Stiff leg derrick The guy derrick consists of a vertical

mast. This mast is supported by the number of guys and can revolve through 360ْ.

While revolving, the radius of revolution should be such that the revolving structure is not obstructed by the guy wires.

The power is supplied by a diesel engine or by an electric motor.

Page 21: Hoisting equipments

A typical derrick crane is illustrated in fig.

This derrick can be constructed upto 200 tonnes capacity .

In stiff leg type derricks, the guy wires are replaced by trussed structure.

This type of derricks are suitable for loads from 10 to 50 tonnes.

Page 22: Hoisting equipments
Page 23: Hoisting equipments

GANTRY CRANES

The Gantry cranes or overhead cranes are the indispensable machines in factories and workshops.

In large workshops, there are separate machines for fabrications or repairs of the machine parts.

The machine or the components, which are to be repaired, can be transferred to the place of fabrication or assembly with the help of Gantry cranes.

Page 24: Hoisting equipments
Page 25: Hoisting equipments

DIFFERENT HOISTING

EQUIPMENTS

Page 26: Hoisting equipments
Page 27: Hoisting equipments
Page 28: Hoisting equipments
Page 29: Hoisting equipments
Page 30: Hoisting equipments
Page 31: Hoisting equipments
Page 32: Hoisting equipments
Page 33: Hoisting equipments

COSTING/ECONOMY Pulley and sheave block :- ₹ 30000 - 120000 Electric chain hoist 2 tonnes:- ₹ 30000 -

1200000 Electric whinches :- ₹ 8400 - 300000 Hydraulic jack :- ₹ 30000 – 84000 Overhead crane or gantry crane :- ₹360000

– 18000000 Tower crane :- ₹6000000 – 12000000 70 tone hydraulic crawler crane :- ₹

1500000 – 18000000 Elevators :- ₹ 600000 – 1800000

Page 34: Hoisting equipments

Fixed Derrick crane :- ₹ 1560000 – 2400000

Mobile cranes :- ₹ 1200000 – 3000000 Truck cranes 7 ton :- ₹ 500000 -

1800000 Truck mounted crrane 70 ton :- ₹

12000000 - 18000000

Page 35: Hoisting equipments

ADVANTAGES OF HOISTING EQUIPMENTS

Hoisting equipment assists in the lifting and positioning of large, heavy loads in a variety of industries, including:

Automotive Chemicals Commercial printing Manufacturing Newspaper Paper Steel Warehousing and distribution

Page 36: Hoisting equipments

Hoisting equipment provides a variety of benefits:

Customizable – Hoisting equipment can be customized with below the hook attachments, end effectors or specialized tooling to handle a diverse variety of products and loads

Ergonomics – By doing the heavy lifting, hoisting equipment takes the strain off operators, reducing fatigue and lowering the risk of injury

Flexible – Hoisting equipment can be easily re-fitted for longer lifting capability

Page 37: Hoisting equipments

Indoor/outdoor use – Hoisting equipment can be used with equipment both inside a facility and outside, on the dock or in the yard

Lower maintenance costs – Incorporating the latest technologies and offered in a variety of usage and capacity ratings, hoisting equipment requires less maintenance compared to other lifting devices

Portable – Hoisting equipment can be easily transported from job to job or site to site

Positioning – Highly automated systems maneuver with the precision of one thousandth of the rated speed to an exact location

Page 38: Hoisting equipments

Reduction in product damage – By allowing for smooth, direct-path lifting over obstacles—with soft start features, multiple speed options and a variety of end effectors to interface with and secure the load—products are handled gently to minimize damage

Safety – Because they operate overhead and work in a specific area, hoisting equipment is less likely than forklift traffic to maneuver a load into personnel, walls, machinery or other obstacles

Page 39: Hoisting equipments

HOW IS HOISTING EQUIPMENT USED?

Hoisting equipment is used in a variety of areas to support processing and handling throughout a facility:

Assembly: Moving products through production processes

Positioning: Securing a component for additional work

Transportation: Loading finished products onto open trailers or railcars

Page 40: Hoisting equipments

Staging: Holding work-in-process for additional production processes

Storage: Transporting heavy items to and from storage areas

Warehousing: Moving large, heavy products to and from docks

Page 41: Hoisting equipments

DISADVANTAGES OF HOISTING EQUIPMENTS

Disadvantage of chain hoist is slow lifting pace and limited places.

Hydraulic engine hoist can take a lot of space in garage.

Electric hoist are not good with heavier loads.

 electric hoist is that they need a special place to be installed.

 electric hoist will be static and cannot be moved around (without special installations), so you will always have to place a reparable car in the same place.

Page 42: Hoisting equipments

 Electric hoist needs to be placed above the ground. This usually means mounting it to ceiling or building a special scaffolding to install an electric hoist.

 Another disadvantage of electric hoist is that it needs an electric power source in order to work. Hydraulic or chain engine hoists need to be operated manually, while electric hoist has got an electrical motor that works with an electrical power.

 electric hoist is fast and convenient tool to use for lifting moderately heavy loads, but becomes much more expensive, if you need to lift loads heavier than 225 kg (500 lb).

Page 43: Hoisting equipments

 The lifting of load is also very slow in chain hoist.

This lifting process in chain hoist is slower than electric hoists or hydraulic hoists.

The cranes used as hoisting equipments are expensive.

 The climbing tower crane disadvantages: 

Due to the direct support tower crane in the construction, the need for checking the structure, when necessary, temporary reinforcement, increased costs. 

Page 44: Hoisting equipments

 Due to the crane installed in the elevator shaft of the building, so the crane installation will affect the construction schedule basement structure.  due to the crane installed in the elevator shaft of the building, so the crane installation will affect the construction schedule basement structure.

driver communication links with the ground is difficult, driver vision is not enough open to lifting bring some security risks.

 after the project is completed, disassemble downstairs need auxiliary lifting equipment, difficult to disassemble, not safety.

Page 45: Hoisting equipments

MANUFACTURERS OF HOISTING EQUIPMENTS

Roughneck Industries Neiko Enterpises Haulmaster Industries Torin Blackbull Goodway industries, Ghaziabad Techno industries, Ahmedabad Hydraulic force Enterprises, delhi Power tech industries, Ludhiana D.A.V. Engineering works, Ludhiana

Page 46: Hoisting equipments

Belt and Bearing house, Ahmedabad Trophy Tech India, Bengaluru Southern Plantaids private Limited

secunderabad Sany Group, etc.

Page 47: Hoisting equipments

HIRING CHARGES OF HOISTING EQUIPMENTS

Truck mounted 70 tone crane :- 40,000/day

Mobile crane 15 tone :- 10,000/day Chain hoist :- 5000/day Tower crane :- 90,000 to 1,20,000/day


Top Related