Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2019 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
ILLUMINATEDDOOR SILL TRIM
served. AII08967-26 (190
2019 PASSPORT
1) 0
Issue Date
JAN 2019
PARTS LIST
Illuminated Door Sill Trim KitP/N 08E12-TGS-100
2 Front illuminated door sill trims
2 Rear illuminated door sill trims
2 Door sill trim harnesses
25 Wire ties
2 Fuse labels
2 Aluminum tapes
4 Alcohol wipes
2 Protective tapes
4 Protective clips
TOOLS AND SUPPLIES REQUIRED
Diagonal cutters
10 mm Open end wrench
Isopropyl alcohol
Scissors
Shop towel
Ruler
Masking tape
The following tools are available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
• Plastic Trim Tool (T/N SILTRIMTL10)
1 of 218E12-TGS-1A00-90
Illustration of the Illuminated Door Sill Trims on the Vehicle
FRONT ILLUMINATED DOOR SILL TRIM
DOOR SILL TRIM HARNESS
2A FUSE FRONT ILLUMINATED DOOR SILL TRIM2A FUSE
DOOR SILL TRIM HARNESS
REAR ILLUMINATED DOOR SILL TRIM
REAR ILLUMINATED DOOR SILL TRIM
INSTALLATION
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
2 of 21 AII08967-2
1. Disconnect the negative cable from the battery:
• Wrap a shop towel around the hood latch.
HOOD LATCH (Wrap with a shop towel.)
• Remove the front bulkhead cover.
FRONT BULKHEAD COVER
10 CLIPS
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
• Remove the intake air tube.
• Disconnect the negative cable from the battery.
INTAKE AIR TUBE2 CLIPS
2. Remove the passenger’s dashboard under cover, and unplug the vehicle connector (if equipped).
PASSENGER’S DASHBOARD UNDER COVER
4 CLIPS
2 PINS VEHICLE CONNECTOR (if equipped)
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
3. Remove the passenger’s door sill trim.
4 CLIPS
2 RETAINING TABS
PASSENGER’S DOOR SILL TRIM
4. Pull away the door opening seal, and remove the passenger’s kick panel.
2 CLIPS
PASSENGER’S KICK PANEL
DOOR OPENING SEAL (Pull away.)
6 (1901) 3 of 21
5. Pull away the door opening seal, and remove the driver’s dashboard side lid.
DOOR OPENING SEAL (Pull away.)
3 CLIPS 2 RETAINING TABS
DRIVER’S DASHBOARD SIDE LID
6. Remove the driver’s dashboard lower cover, and unplug the vehicle connectors, and release the vehicle sensor.
12 CLIPSVEHICLE CONNECTORS
2 RETAINING TABS
VEHICLE SENSOR
DRIVER’S DASHBOARD LOWER COVER
4 of 21 AII08967-2
7. Remove the driver’s door sill trim.
2 RETAINING TABS
4 CLIPS
DRIVER’S DOOR SILL TRIM
8. Pull away the door opening seal, and remove the driver’s kick panel.
2 CLIPS
DRIVER’S KICK PANEL
DOOR OPENING SEAL (Pull away.)
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
9. Attach a piece of masking tape to the vehicle panel as shown.
LEFT REAR MIDDLE DOOR SILL TRIM
VEHICLE PANEL
MASKING TAPE
MASKING TAPE
85 mm (3.35 in.)
10. Remove the left second row seat front foot cover.
CLIP
LEFT SECOND ROW SEAT FRONT FOOT COVER
2 RETAINING TABS
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
11. Fold down the left second row seat, and move it forward.
LEFT SECOND ROW SEAT
Fold down.
Move forward.
12. Remove the left rear upper door sill trim.
2 CLIPS
LEFT REAR UPPER DOOR SILL TRIM
7 RETAINING TABS
6 (1901) 5 of 21
13. Remove the left rear middle door sill trim.
10 CLIPS
LEFT REAR MIDDLE DOOR SILL TRIM
CLIP
14. Remove the left rear lower door sill trim.
3 CLIPS
LEFT REAR LOWER DOOR SILL TRIM
2 RETAINING TABS
6 of 21 AII08967-2
15. Remove the left center pillar lower trim cover.
LEFT CENTER PILLAR LOWER TRIM COVER
3 RETAINING TABS
16. Remove the left center pillar lower trim.
LEFT CENTER PILLAR LOWER TRIM
4 RETAINING TABS
17. Repeat steps 9 through 16 on the right side of the vehicle.
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
18. Using scissors, cut the protective tapes as shown.
A
PROTECTIVE TAPE
B
30 mm (1.18 in.)
30 mm (1.18 in.)30 mm
(1.18 in.)
30 mm (1.18 in.)
30 mm (1.18 in.)
40 mm (1.57 in.)
40 mm (1.57 in.)
A
PROTECTIVE TAPE
30 mm (1.18 in.)
40 mm (1.57 in.)
40 mm (1.57 in.)
B
19. Pull away the door opening seal as shown.
DOOR OPENING SEAL(Pull away.) DRIVER’S DOOR
SILL TRIM OPENING
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
20. Using an alcohol wipe, thoroughly clean the vehicle panel where the front illuminated door sill trim will attach.
VEHICLE PANEL
ALCOHOL WIPE Clean with the
alcohol wipe.
21. Remove the two adhesive backings from the front illuminated door sill trim.
2 ADHESIVE BACKINGS (Remove.)
FRONT ILLUMINATED DOOR SILL TRIM
6 (1901) 7 of 21
22. Line up the cutout shape on the front illuminated door sill trim with the bump shape on the vehicle panel. Press down firmly on the adhesive part of the front illuminated door sill trim firmly.
FRONT ILLUMINATED DOOR SILL TRIM
FRONT ILLUMINATED DOOR SILL TRIM
Line up.VEHICLE PANEL
CUTOUT SHAPE
VEHICLE PANEL
Line up.BUMP SHAPE
8 of 21 AII08967-2
23. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel where the protective tape will attach. Attach one protective tape A to the vehicle panel as shown.
FRONT ILLUMINATED DOOR SILL TRIM
VEHICLE PANEL
FRONT ILLUMINATED DOOR SILL TRIM HARNESS
PROTECTIVE TAPE A
Clean with isopropyl alcohol.
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
24. Install the protective clip to the protective tape A on the vehicle panel.
FRONT ILLUMINATED DOOR SILL TRIM HARNESS
PROTECTIVE CLIP
PROTECTIVE TAPE B
PROTECTIVE CLIP
FRONT ILLUMINATED DOOR SILL TRIM
PROTECTIVE TAPE A
25. Line up and route the front illuminated door sill trim harness over the protective clip as shown.
26. Secure the front illuminated door sill trim harness to the protective clip with one protective tape B.
27. Pull away the door opening seal as shown.
DOOR OPENING SEAL(Pull away.) LEFT REAR LOWER DOOR
SILL TRIM OPENING
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
28. Using an alcohol wipe, thoroughly clean the vehicle panel where the rear illuminated door sill trim will attach.
VEHICLE PANEL
ALCOHOL WIPE Clean with the
alcohol wipe.
29. Peel back the adhesive backing, and tape it to the front surface of the rear illuminated door sill trim with masking tape. Remove the adhesive backing from the rear illuminated door sill trim.
ADHESIVE BACKING(Peel back.)
REAR ILLUMINATED DOOR SILL TRIM
ADHESIVE BACKING(Remove.)
MASKING TAPE
Temporarily attach.
6 (1901) 9 of 21
30. Line up the rear illuminated door sill trim with the masking tape. Attach the rear illuminated door sill trim to the vehicle panel.
MASKING TAPE
VEHICLE PANEL
REAR ILLUMINATED DOOR SILL TRIM
31. While applying light pressure against the rear illuminated door sill trim, carefully remove the taped adhesive backing.
ADHESIVE BACKING(Remove.)
REAR ILLUMINATED DOOR SILL TRIM
32. Using the palm of your hand, firmly press the rear illuminated door sill trim against the vehicle panel.
33. Remove the masking tape.
10 of 21 AII08967-2
34. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel where the protective tape will attach. Attach one protective tape A to the vehicle panel as shown.
REAR ILLUMINATED DOOR SILL TRIM
VEHICLE PANEL
REAR ILLUMINATED DOOR SILL TRIM HARNESS
PROTECTIVE TAPE A
Clean with isopropyl alcohol.
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
35. Install the protective clip to the protective tape A on the vehicle panel.
REAR ILLUMINATED DOOR SILL TRIM HARNESS
PROTECTIVE CLIP
PROTECTIVE TAPE B
PROTECTIVE CLIP
PROTECTIVE TAPE A
REAR ILLUMINATED DOOR SILL TRIM
36. Line up and route the rear illuminated door sill trim harness over the protective clip as shown.
37. Secure the rear illuminated door sill trim harness to the protective clip with one protective tape B.
38. Repeat steps 19 through 37 on the right side of the vehicle.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
39. Using isopropyl alcohol on a shop towel, thoroughly clean the fuse case where the fuse label will attach. Attach the fuse label (2A STEP ILLUMI) to the fuse case on the door sill trim harness. Repeat on the remaining door sill trim harness.
FUSE CASE
DOOR SILL TRIM HARNESS
Clean with isopropyl alcohol.
FUSE LABEL(2A STEP ILLUMI)
6 (1901) 11 of 21
If the vehicle is equipped with another accessory harness, continue with step 40; otherwise, go tostep 42.
With another accessory harness
40. Unplug the other accessory harness 2-pin connector, and plug the vehicle 2-pin connector into the door sill trim harness 2-pin connector.
DOOR SILL TRIM HARNESS 2-PIN CONNECTORS
TAPE (Remove.)
OTHER ACCESSORY HARNESS 2-PIN CONNECTOR
VEHICLE 2-PIN CONNECTOR
DRIVER’S DASHBOARD LOWER COVER OPENING
41. Remove the tape to free the door sill trim harness 2-pin connector, and plug it into the other accessory harness 2-pin connector. Go to step 43.
12 of 21 AII08967-2
Without another accessory harness
42. Plug the vehicle 2-pin connector into the door sill trim harness 2-pin connector.
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
VEHICLE 2-PIN CONNECTOR
DRIVER’S DASHBOARD LOWER COVER OPENING
43. Secure the door sill trim harness to the vehicle harness with two wire ties.
VEHICLE HARNESS
2 WIRE TIES
DOOR SILL TRIM HARNESS
VEHICLE HARNESS
DRIVER’S KICK PANEL OPENING
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
44. Route the door sill trim harness along the vehicle harness.
DOOR SILL TRIM HARNESS
VEHICLE HARNESS
DRIVER’S DOOR SILL TRIM OPENING
45. Route the door sill trim harness along the vehicle harness.
LEFT CENTER PILLAR LOWER TRIM OPENING
DOOR SILL TRIM HARNESS
VEHICLE HARNESS
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
46. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel where the aluminum tape will attach.
ALUMINUM TAPE (Cut in half.)
VEHICLE PANEL
ALUMINUM TAPE
Clean with isopropyl alcohol.
REAR ILLUMINATED DOOR SILL TRIM HARNESS
LEFT REAR LOWER DOOR SILL TRIM OPENING
ALUMINUM TAPE
SECTION VIEW
REAR ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE PANEL
47. Using scissors, cut one aluminum tape in half, and secure the rear illuminated door sill trim harness to the vehicle panel with one piece of aluminum tape as shown.
6 (1901) 13 of 21
48. Route the rear illuminated door sill trim harness along the vehicle harness, and secure it to the vehicle harness with one wire tie as shown.
VEHICLE PANEL
REAR ILLUMINATED DOOR SILL TRIM HARNESS VEHICLE
HARNESS
SECTION VIEW
WIRE TIE
VEHICLE HARNESS
WIRE TIE
REAR ILLUMINATED DOOR SILL TRIM HARNESS
LEFT CENTER PILLAR LOWER TRIM OPENING
14 of 21 AII08967-2
49. Plug the door sill trim harness 2-pin connector into the rear illuminated door sill trim harness 2-pin connector.
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
REAR ILLUMINATED DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
REAR ILLUMINATED DOOR SILL TRIM HARNESS(Bundle up the excess.)
2-PIN CONNECTORS VEHICLE HARNESS
2 WIRE TIES
DOOR SILL TRIM HARNESS
LEFT CENTER PILLAR LOWER TRIM OPENING
50. Bundle up the excess rear illuminated door sill trim harness, and secure it and the 2-pin connectors to the vehicle harness with two wire ties as shown.
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
51. Secure the door sill trim harness to the vehicle harness with three wire ties as shown.
VEHICLE PANEL
DOOR SILL TRIM HARNESS VEHICLE
HARNESS
SECTION VIEW
WIRE TIE
VEHICLE HARNESS
3 WIRE TIES
DRIVER’S DOOR SILL TRIM OPENING
DOOR SILL TRIM HARNESS
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
52. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel where the aluminum tape will attach.
VEHICLE PANEL
ALUMINUM TAPE
Clean with isopropyl alcohol.
FRONT ILLUMINATED DOOR SILL TRIM HARNESS
ALUMINUM TAPE(Cut in step 47.)
DRIVER’S DOOR SILL TRIM OPENING
53. Secure the front illuminated door sill trim harness to the vehicle panel with one piece of aluminum tape cut in step 47.
6 (1901) 15 of 21
54. Route the front illuminated door sill trim harness along the vehicle harness, and secure it and door sill trim harness to the vehicle harness with three wire ties as shown.
FRONT ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE HARNESS
3 WIRE TIES
SECTION VIEW
WIRE TIE
FRONT ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE PANEL
VEHICLE HARNESS
DOOR SILL TRIM HARNESS
DRIVER’S DOOR SILL TRIM OPENING
DOOR SILL TRIM HARNESS
55. Plug the door sill trim harness 2-pin connector into the front illuminated door sill trim harness 2-pin connector.
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
FRONT ILLUMINATED DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
DRIVER’S KICK PANEL OPENING
16 of 21 AII08967-2
56. Bundle up the excess front illuminated door sill trim harness, and secure it and the 2-pin connectors to the vehicle harness with three wire ties as shown.
3 WIRE TIES
VEHICLE HARNESS
2-PIN CONNECTORS
FRONT ILLUMINATED DOOR SILL TRIM HARNESS(Bundle up the excess.)
DOOR SILL TRIM HARNESS
DRIVER’S KICK PANEL OPENING
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
If the vehicle is equipped with another accessory harness, continue with step 57; otherwise, go to step 61.
With another accessory harness
57. Unplug the other accessory harness 2-pin connector, and plug the vehicle 2-pin connector into the door sill trim harness 2-pin connector.
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
TAPE (Remove.)
OTHER ACCESSORY HARNESS 2-PIN CONNECTOR
VEHICLE 2-PIN CONNECTOR
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
PASSENGER’S KICK PANEL OPENING
58. Remove the tape to free the door sill trim harness 2-pin connector, and plug it into the other accessory harness 2-pin connector.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
59. Secure the door sill trim harness to the vehicle harness with one wire tie.
DOOR SILL TRIM HARNESS
PASSENGER’S KICK PANEL OPENING
WIRE TIEVEHICLE HARNESS
60. Bundle up the excess other accessory harness, and secure it and the 2-pin connectors to the vehicle harness with two wire ties as shown. Go to step 63.
DOOR SILL TRIM HARNESS
PASSENGER’S KICK PANEL OPENING
2 WIRE TIESVEHICLE HARNESS
OTHER ACCESSORY HARNESS(Bundle up the excess.)
2-PIN CONNECTORS
6 (1901) 17 of 21
Without another accessory harness
61. Plug the vehicle 2-pin connector into the door sill trim harness 2-pin connector.
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
VEHICLE 2-PIN CONNECTOR
PASSENGER’S KICK PANEL OPENING
62. Secure the door sill trim harness to the vehicle harness with three wire ties.
VEHICLE HARNESS
3 WIRE TIES
DOOR SILL TRIM HARNESS
PASSENGER’S KICK PANEL OPENING
18 of 21 AII08967-2
63. Route the door sill trim harness along the vehicle harness.
DOOR SILL TRIM HARNESS
VEHICLE HARNESS
PASSENGER’S DOOR SILL TRIM OPENING
64. Route the door sill trim harness along the vehicle harness.
RIGHT CENTER PILLAR LOWER TRIM OPENINGDOOR SILL
TRIM HARNESS
VEHICLE HARNESS
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
65. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel where the aluminum tape will attach.
ALUMINUM TAPE (Cut in half.)
VEHICLE PANEL
ALUMINUM TAPE
Clean with isopropyl alcohol.
REAR ILLUMINATED DOOR SILL TRIM HARNESS
RIGHT REAR LOWER DOOR SILL TRIM OPENING
ALUMINUM TAPE
SECTION VIEW
REAR ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE PANEL
66. Using scissors, cut one aluminum tape in half, and secure the rear illuminated door sill trim harness to the vehicle panel with one piece of aluminum tape as shown.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
67. Route the rear illuminated door sill trim harness along the vehicle harness, and secure it to the vehicle harness with two wire ties as shown.
VEHICLE PANEL
REAR ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE HARNESS
SECTION VIEW
WIRE TIE
VEHICLE HARNESS
2 WIRE TIES
REAR ILLUMINATED DOOR SILL TRIM HARNESS
RIGHT REAR LOWER DOOR SILL TRIM OPENING
6 (1901) 19 of 21
68. Plug the door sill trim harness 2-pin connector into the rear illuminated door sill trim harness 2-pin connector, and secure the 2-pin connectors and door sill trim harness to the vehicle harness with three wire ties as shown.
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
REAR ILLUMINATED DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
2-PIN CONNECTORS
VEHICLE HARNESS
WIRE TIE
RIGHT CENTER PILLAR LOWER TRIM OPENING
VEHICLE PANEL
REAR ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE HARNESS
SECTION VIEW
WIRE TIE
DOOR SILL TRIM HARNESS
2 WIRE TIES
VEHICLE HARNESS
20 of 21 AII08967-2
69. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel where the aluminum tape will attach.
VEHICLE PANEL
ALUMINUM TAPE
Clean with isopropyl alcohol.
FRONT ILLUMINATED DOOR SILL TRIM HARNESS
ALUMINUM TAPE(Cut in step 66.)
PASSENGER’S DOOR SILL TRIM OPENING
70. Secure the front illuminated door sill trim harness to the vehicle panel with one piece of aluminum tape cut in step 66.
6 (1901) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
71. Route the front illuminated door sill trim harness along the vehicle harness, and secure it and door sill trim harness to the vehicle harness with two wire ties as shown.
FRONT ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE HARNESS
2 WIRE TIES
SECTION VIEW
WIRE TIE
FRONT ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE PANEL
VEHICLE HARNESS
DOOR SILL TRIM HARNESS
DOOR SILL TRIM HARNESS
PASSENGER’S DOOR SILL TRIM OPENING
72. Plug the door sill trim harness 2-pin connector into the front illuminated door sill trim harness 2-pin connector, and secure the 2-pin connectors and door sill trim harness to the vehicle harness with one wire tie.
WIRE TIE2-PIN CONNECTORS
VEHICLE HARNESS
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
FRONT ILLUMINATED DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
PASSENGER’S DOOR SILL TRIM OPENING
DOOR SILL TRIM HARNESS
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII08967-2
73. Check that all wire harnesses are routed properly and all connectors are plugged in.
74. Install all removed parts except for the front bulkhead cover and the intake air tube.
75. Connect the negative cable to the battery.
76. Install the front bulkhead cover and the intake air tube.
77. Press and hold the audio unit power button for 2 seconds to restore the audio and navi (if equipped) system functions.
78. Set the clock on vehicles without navigation.
79. If necessary, restore the system back to normal operation as described in the service information.
Check the Operation of the Illuminated Door Sill Trims
80. Make sure the lights come on when you open each door.
6 (1901) 21 of 21