VOLT® Low Voltage Landscape Lighting VOLT® Path & Area Light StemVSM-2407 & VSM-1203
INSTALLATION INSTRUCTIONS
Specifications and product details subject to change without notice. © Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -
VOLT® Path & Area Light StemVSM-2407 & VSM-1203
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
This fixture is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this fixture.
2. Warning: this fixture is not intended to be installed within 10 feet [3 meters] of a pool, spa or fountain.
3. This fixture is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in order to connect to the main low voltage cable.
5. Wiring connections must be made with wire connectors that are suitable for outdoor use.
6. Position the wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting.
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.1. Turn off/unplug and allow to cool before reducing lamp.2. Lamp gets HOT quickly!3. Do not touch the hot lens, guard or cowl.4. Keep lamp away from materials that may burn.5. Do not touch lamp at any time.6. Use a soft cloth.7. Oil from skin may damage lamp.8. Do not operate the fixture with a damaged or missing lens or shield.
!
!
w w w . v o l t l i g h t i n g . c o m- 2 -
Package Contents
Product Dimensions
A. (1) Stem
[email protected] • 813.978.3700
2.5”
9”
- 3 -
22.5”
Parts Required (sold separatly)
A. (1) Hat B. (1) Bulb
C. Stake
Max Spread Hat Pictured Here
w w w . v o l t l i g h t i n g . c o m
INSTALLATION INSTRUCTIONS
Remove Stem Top1Loosen the stem top and remove it from the stem.
Stem Top
Stem
- 4 -
Install Bulb2Insert the bulb with correct wattage and type marked on the fixture label and push firmly into place.
CAUTION: Do not exceedmaximum wattage marked onluminaire label.
Socket
Bulb
Place the stem top over thebulb and thread the stem top onto the stem. Hand tighten until snug.
Install Stem Top3
Stem Top
Stem
VOLT® Path & Area Light StemVSM-2407 & VSM-1203
[email protected] • 813.978.3700- 5 -
Install Stake4Determine the desired location formounting the fixture. Hammer thestake into the ground until the flangeof the stake is flush to grade. To avoiddamage to the stake, place a boardon top of the stake while hammering.
NOTE: If the ground is hard and thestake is difficult to install, make acrosscut in the ground using a flatshovel.
Board
Stake
Soil
Ground
Clear away an area in the ground at the wireway slot on the top of the stake. Lay the luminaire pigtail into the wireway slot and attach the stem onto the stake. Tighten until snug.
Install Stem to Stake5
Stem
Stake
Pigtail
Wireway Slot
INSTALLATION INSTRUCTIONS
w w w . v o l t l i g h t i n g . c o m- 6 -
Wire Connection6
Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.
Pigtail
Main Supply CableWire Connectors
Install Hat7Place the hat of your choice onto the stem top and secure it with the finial. Hand tighten until snug.
Shield
Finial
Hat of your choice
Install/Replace Bulb
Remove the finial, hat and stem top to expose the bulb. Replace itwith the correct wattage and type marked on the fixture label. Then,reinstall the stem top and hat.
IMPORTANT: Bulbs must be protected from moisture and dust at alltimes. Always reinstall the stem top and hat when removed.
VOLT® Path & Area Light StemVSM-2407 & VSM-1203
[email protected] • 813.978.3700- 7 -
IS-VSM-2407/1203-ver1.pdf
Specifications and product details subject to change without notice. © Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
w w w . v o l t l i g h t i n g . c o m
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 8 -