Download - JSAE Paper Number 20025335
-
7/30/2019 JSAE Paper Number 20025335
1/4
20025335
324 A Class of Optimal Broadband Beamformer
Geometries Designed for Easy Construction
Jacob J. CHRISTENSEN and Jrgen HALD
Brel & Kjr Sound & Vibration Measurement A/S, Skodsborgvej 307, DK-2850 Nrum, Denmark
Very regular beamformer array geometries will have Grating Lobes in their directivity
pattern when applied above a certain frequency. The grating lobes can be suppressed by
removing periodicities, typically by the use of random arrays or spiral arrays. Large
irregular arrays are, however, difficult to build due to their complicated support structure
and cabling. The present paper describes a novel array design, which maintains the low
grating lobe level of irregular arrays, but which has a regularity that allows a much simpler
support structure and cabling. The performance is compared with that of comparable
irregular arrays, and verified through practical measurements
Keywords: Noise Source Location, Phased Array, Beamforming.
1. INTRODUCTION
As illustrated in Figure 1, we consider a planar array of
Mmicrophones at locations in the
xy-plane of our coordinate system. When such an arrayis applied for Delay-and-Sum Beamforming, the
measured pressure signals are individually delayed
and then summed, [1]:
),...,2,1( Mmm =r
mp
. (1)=
=M
m
mm tptb1
))((),(
The individual time delays are chosen with the aim
of achieving selective directional sensitivity in a specific
direction, characterized here by a unit vector
m
. Thisobjective is met by adjusting the time delays in such a
way that signals associated with a plane wave, incidentfrom the direction , will be aligned in time before theyare summed. Geometrical considerations (see Figure 1)show that this can be obtained by choosing:
c
mm
r = , (2)
where c is the propagation speed of sound. Signals
arriving from other far-field directions will not bealigned before the summation, and therefore they willnot coherently add up.
The frequency domain version of expression (1) for theDelay-and-Sum beamformer output is:
(3)
=
=
=
=
M
m
jm
M
m
jm
m
m
eP
ePB
1
1
)(
)(
)(),(
rk
Here, is the temporal angular frequency, k k isthe wave number vector of a plane wave incident from
the direction
in which the array is focused seeFigure 1 and ck= is the wave number. In
equation (3) an implicit time factor equal to is
assumed. Through our choice of time delays
tje
)(m , or
equivalently of the preferred wave number vector
k k , we have tuned the beamformer on the far-field direction . Ideally we would like to measure
only signals arriving from that direction, in order to get aperfect localization of the sound source. To investigate,
how much leakage we will get from plane wavesincident from other directions, we assume now a plane
wave incident with a wave number vector k differentfrom the preferred k
0
k . The pressure measured bythe microphones will then be:
jeP k
= 00
1
)( 0 rkk ej
=
M
m
j me1
rK
P
),( =B
W
r
m
)
0M
m
)K
)0
,x K
k
K
=
, (4)mmr(
which according to equation (3) will give the followingoutput from the beamformer:
. (5)(0 k WPP
Here, the function W
(6)(
is the so called Array Pattern, defined entirely by thearray geometry. It has the form of a generalized spatialDFT of a weighting function, which equals one over thearray area and zero outside. Because the microphone
positions havez-coordinate equal to zero, the Array
Pattern is independent of . We shall therefore
consider the Array Pattern W only in the (
plane, i.e. we consider the projections of the wave
m
zK
)y
2002 JSAE Spring Convention 1/4
-
7/30/2019 JSAE Paper Number 20025335
2/4
20025335
number vectors onto that plane. There, W has an areawith high values around the origin with a peak value
equal to M at . According to
equation (5), this peak represents the high sensitivity toplane waves coming from the direction
)0,0(),( =yx KK
, in which the
array is focused. Figure 1 contains an illustration of thatpeak, which is called the mainlobe. Other directionalpeaks, which are calledsidelobes, will cause waves from
such directions to leak into the measurement of themainlobe direction . This will produce falsepeaks/images in a measured directional source map. A
good phased array design can therefore be characterizedby having low Maximum Sidelobe Level (MSL),measured relative to the mainlobe level. With reference
to equation (5), both kand k have length equal to the
wave numberk, and they can have opposite direction pointing for example in the positive and negative x-axis
directions meaning that
0
k20 kk . Therefore, at
a given frequency only the section ck 22 =K
of the Array Pattern will be visible. And if the Array
Pattern has low MSL for cmax2=K maxK ,
then a beamformer application will provide accuratedirectional source maps with a low degree of false
images up to the frequency cmaxK21
max = . If the
beamformer will be focused on directions not more
than 30 off-axis, then the projection of the wave
number vector k on the array plane will be
shorter than
0)( k
k23 . Therefore only the section
ck 23
23 =K will be visible, so the upper
limiting frequency becomes cKmax32
max )30( = .
Phased Array of Microphones
rm
Plane wave
k k=
Origin
Main
lobe
Figure 1: Illustration of a phased microphonearray, a directional sensitivity represented by a
mainlobe, and a Plane wave incident from the
direction of the mainlobe.
The width of the mainlobe of the Array Pattern can beestimated from the similarity of the expression (5) with a
2D DFT of a rectangular type of spatial window
function covering the area of the array: The mainlobewidth will be inversely proportional to the diameterD ofthe array, and the first null will be approximately at
DK 2min ==K , [1].
2. OPTIMAL ARRAY GEOMETRIES
Very regular phased array geometries, with a highdegree of periodicity, will have so-called grating lobesin their directivity pattern, when they are applied above acertain frequency. A grating lobe is a sidelobe withamplitude of the same size as the mainlobe, created byspatial aliasing. Consider as an example a rectangular
array with constant microphone spacing din both the x-and they-direction. For such an array, the Array PatternW of equation (6) will have a first grating lobe at
)0,2(),( dKK yx = . According to the above
description, this grating lobe will enter the visible
region at the frequency for which dc /22 = .
At that frequency the microphone spacing d is equal tohalf a wavelength. At higher frequency there may befalse images of the same magnitude as the true image inmeasured directional source maps.
Grating lobes can be avoided by removing theperiodicities, for example by the use of randomgeometries, which will provide a variety of differentspatial sampling intervals and thereby suppress thespatial aliasing problems, [1]. Large random arrays are,however, much more difficult to build than more regulararrays. Both the support structure and the cabling aremore complicated and as a consequence the operation inthe practical measurement situation is difficult or
tedious. Various non-random designs have beenintroduced, which provide also a variety of different
spatial sampling intervals and therefore rather lowMSLover a wide frequency range for example arraygeometries based on one or several concentriclogarithmic spirals, [2], or on an Archimedes spiral, [3].But the spiral arrays are still quite complicated to builddue to the complicated curved geometries. See Figure 2.Also, the need for high resolution in the far field canonly be met with relatively large dimensions of thearrays. Thus, an array with a diameter of several metersis often required. In connection with outdoorapplications it is therefore of practical importance thatthe array construction allows for easy assembly anddisassembly at the site of use, and for easy transport.
2002 JSAE Spring Convention 2/4
-
7/30/2019 JSAE Paper Number 20025335
3/4
20025335
Figure 2: Schematic representation of a 90 ch.
Archimedes spiral with the same diameter (2.43m)
as the B&K wheel array [Fig.3]. The microphone
spacing, measured as arc length along the spiral
curve, is 0.3 m.
Figure 3 shows an example of a new-patented
Wheel Array design, which can be optimized to havevery lowMSL over a wide frequency band, but which isbuilt of a set of identical line arrays, simplifying themechanical construction and the cabling. The patenteddesign consists of typically an odd numberN of smallidentical line arrays arranged around a center as spokes
in a wheel, with identical angular spacing between thespokes. All spokes are tilted the same angle away fromradial direction. The geometry is invariant under a
rotation around the center, n being any
integer. The mechanical design of the array shown inFigure 3 is fully modular: all spokes can easily bedetached from the supporting inner and outer ringswhich themselves can be disassembled. Thus the whole
array structure can be disassembled and transported in astandard size flight case. Regarding the cabling each
spoke mounts 6 microphones, which through integratedcabling, are connected to a common plug (LEMO-connector). Each spoke is then connected to a 6-channelinput module through a single cable. Despite itsirregularity the Wheel Array has its sensors grouped ineasily identifiable logical units. In a practical
measurement situation, which requires channel
detection, calibration and occasionally detection ofhardware faults, this is a great advantage.
Nn /360
Minimize Max |W(K)| over the area
cD
max22 K , (7)
Figure 3: Example of a 90-channel Brel & Kjr
wheel array for beamforming. The wheel array
depicted has 15 identical spokes, with integrated
cabling, each carrying 6 microphones. The wheel
diameter is 2.43 m (patent pending).
Here, max is the upper limiting frequency for use of
the array. This optimization is performed by the use of a
Minimax optimization program.The Wheel Array of Figure 3 was optimized with
max = 3.0 kHz. For a given diameter and number of
channels the Archimedes spiral array can be optimizedfor a given frequency range by adjusting the microphonespacing, d (d = 0.3m was chosen for optimal
performance below 3 kHz).
The array diameter determines the width of themainlobe and thus the angular resolution. Havingselected the array diameterD, the number of spokes and
the number of microphones per spoke, the followingvariables are adjusted to provide the lowest possiblevalue of the MSL: 1) The rotation of the spokes awayfrom radial direction. 2) The position of the microphoneson a spoke. With 6 microphones on each spoke, wehave 7 adjustable parameters to minimize the MSL over
the following area in the Array Pattern (see section 1):
Figure 4 shows the MSL as a function of frequency forthe optimized Wheel Array of Figure 3 and thecomparable spiral array shown in Figure 2 These arrayshave approximately the same diameterD = 2.43m and
therefore the same mainlobe width (2/D) and spatialangular resolution. Both arrays are designed for the
frequency range 0.5 3.0 kHz but clearly the WheelArray is superior in performance.Due to the grating lobes, which always are present inregular arrays, the traditional X-shaped arrays and
rectangular grid-arrays perform even worse. Seereference [5] for a discussion.
2002 JSAE Spring Convention 3/4
-
7/30/2019 JSAE Paper Number 20025335
4/4
20025335
2002 JSAE Spring Convention 4/4
3. MEASUREMENTS
In order to demonstrate the capabilities of the 90 ch.Wheel Array of Figure 3 we have performed ameasurement on a car (Volvo S60). The vehicle wasinstalled in an in-door test bench and the engine wasoperated at 2500 RPM with no load. The Wheel Array
was placed in parallel with the side of the car at adistance of 2.9m and the stationary sound field wasrecorded for 5 sec. at 16 KHz sampling rate using theBrel & Kjr Acoustic Test Consultant (Type 7761)running on the PULSE measurement system. Data werepost-processed with the PULSE Beamformingapplication (Type 7768) and a representative result is
shown in Figure 5. Despite acoustically challengingmeasurement conditions (back ground noise andreflecting walls, ceiling and floor) a useful dynamicrange of 12 dB is achieved. The beamformingcalculation clearly reveals a leakage from the frontwheel box at high frequencies.
-18
-15
-12
-9
-6
-3
0
0 1000 2000 3000 4000 5000
f [Hz]
MSL
[dB]
90 ch. Archimedes
spiral
90 ch. B&K wheel
array
Figure 4: MSL as function of frequency for the B&K
Wheel array [Fig.3] and the spiral array [Fig.2].
Figure 5: Beamforming result using the 90 ch. B&K
Wheel Array shown in Figure 3. The upper display
shows the sound pressure levels resulting from the
beamforming calculation as a contour plot. The
lower display gives the spectrum in 1/3-octave bandsat a point on the front tire, and the highlighted
interval (2.03.15 kHz) is the selected frequency
range which the contour plot covers. (Screen-shot
from the PULSE Beamforming application).
REFERENCES
1. D. H. Johnson and D. E. Dudgeon, ArraySignal Processing: Concepts and Techniques,Prentice Hall, New Jersey, 1993.
4. CONCLUSION 2. J. R. Underbrink and R. P. Dougherty, Array
Design for Non-intrusive Measurement ofNoise Sources,Proceedings of Noise-Con 96,757-762, 1996.
The new-patented Wheel Array with tilted spokes can beoptimized to have low Maximum Sidelobe Level (MSL)over a very broad frequency range. Its performance issuperior to that of comparable Archimedes spiral arrays.The Wheel Array type has an irregular geometry but due
to its modular construction it is easy to manufacture,transport and operate. As demonstrated by practicalmeasurements the low sidelobe levels of the WheelArray makes its useful even in acoustically non-idealenvironments.
3. A. Nordborg, J. Wedemann and L. Willenbrink,Optimum Array Microphone Configuration,
Proceedings of Inter-Noise 2000.4. G. Elias, Source Localization with a Two-
dimensional Focused Array: Optimal SignalProcessing for a Cross-shaped Array,Proceedings of Inter-Noise 95, 1175-1178,1995.
5. J. Hald and J.J. Christensen, to appear inProceedings of Inter-Noise 2002.