Our Home from Scratch LLC Page 1 CabinetsfromScratch.com
Kitchen Base Cabinet:
Single Drawer with Double Doors
by
Cabinets from Scratch
Our Home from Scratch LLC Page 2 CabinetsfromScratch.com
Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for
any loss, damage, disappointment, injury or death resulting from following the
procedures or techniques described in these plans. Our Home from Scratch LLC
and its legal owners assume no risk and cannot be held responsible for any misuse
of these plans either directly or indirectly. They make no statements as to the
weight or strength capacity of the item described in these plans.
These plans may contain errors and Our Home from Scratch LLC and its legal
owners cannot be held responsible for any error. No guarantee is made as to the
quality of any product that is described herein.
Always use appropriate Personal Protection Equipment when working with tools
and exercise caution if taking any action associated with these plans.
Attempt at your own risk. Some woodworking skills are required. Sorry if that’s a
bummer.
This procedure contains affiliate links.
Distribution Policy By downloading these plans you consent to this distribution policy. These plans
are not to be distributed in anyway without the express consent of Our Home
from Scratch LLC or its legal owners. The individual pictures or procedures
contained herein are also not to be copied or shared.
Our Home from Scratch LLC Page 3 CabinetsfromScratch.com
Introduction
These plans for a base kitchen cabinet are nearly identical to the kitchen
cabinets I built from scratch in my first home in Philadelphia. They design has
been updated to include better joinery methods and the doors and drawers are
overlay instead of inset, which makes the project easier for entry level
woodworkers.
The cabinet box is made from 3/4” thick plywood and includes a 3/4" thick
back board. While this thicker back board makes the cabinet heavier and slightly
more expensive, it also adds strength, rigidity and reduces the different types of
plywood you’ll need to purchase and manage. It’s the same approach I took in
my kitchen cabinets.
Feel free to add additional fasteners to this project if the sides of the
cabinet will be between other cabinets or walls.
The drawers are made from solid maple hardwood and birch plywood and I
recommend you stick with that material since it’s more attractive and it will hold
up much better over time compared to pine or other softwoods.
If you get stuck on any particular part of these woodworking plans, feel free
to email me at [email protected] with any questions. For full
cabinet building training, visit CabinetsfromScratch.com for more information on
our comprehensive video training course.
I hope you enjoy the challenge of building this project.
R,
John Gerard
Our Home from Scratch LLC Page 4 CabinetsfromScratch.com
Getting Started These woodworking plans will take you step by step through the build of a
kitchen base cabinet with a single drawer and two doors. The first thing you
should do is read through these procedures to familiarize yourself with the
materials, tools and skill requirements necessary to complete them.
Tools The tools and miscellaneous supplies I used for this project include the
following:
1. Table Saw with 60 tooth saw blade
2. Miter Saw (also with 60 tooth saw blade)
3. Pneumatic Brad Nail Gun with Pancake Compressor
4. Pocket Screws
5. Dado Blade Set
6. Cordless Drill
7. Wood Glue
8. 3/4" Long Brad Nails
9. K-Body Clamps
Dimensions This cabinet is designed to the following dimensions:
1. Width: 36”
2. Height: 34 ½”
3. Depth: 24”
This version of the cabinet has ¾” overlay doors and drawers. Feel free to
modify the plans to meet your needs. A customizable version of these plans in
MS Excel are available to Cabinets from Scratch subscribers.
Our Home from Scratch LLC Page 5 CabinetsfromScratch.com
Material: Listed below in Table 1 is a list of all the lumber you’ll need to build one
cabinet. All of this lumber should be available at your local large hardware store
(Lowe’s, Home Depot, True Value, etc.), except for the maple. Half-inch thick
hardwood maple boards can be purchased from your local lumberyard or ordered
online. Many lumberyards will also plane down a ¾” thick maple board to ½”
thick upon request and possibly for a small fee. If you can’t find ½” thick maple,
feel free to substitute it with ½” thick oak, which is more readily stocked at large
home improvement stores. Avoid softwoods like pine for this project.
TABLE 1: LUMBER PURCHASE LIST
Item Description Width Length (in) Qty
1 3/4" Thick Birch or Oak Plywood 48” 96” 1
2 3/4" Thick Birch or Oak Plywood 24” 48” 1
3 3/4” Thick Poplar or Oak Hardwood 2 ½” 96” 4
4 3/4" Thick Poplar or Oak Hardwood 7 ½” 36” 1
5 1/2" Thick Birch or Oak Plywood 24” 48” 1
6 1/2” Thick Maple Hardwood 4 ½” 96” 1
7 1/4" Thick Birch Plywood 48” 48” 1
Our Home from Scratch LLC Page 6 CabinetsfromScratch.com
Hardware:
You’ll also need to purchase the following material to complete your
cabinet build. The drawer parts were sized to accept a Blum drawer runner. If you
decide to purchase a different drawer runner, you might need to resize the
drawer parts. Blum components are not cheap, but they work really well. There
are less expensive options available, but again, you’ll probably have to resize the
drawer box to match different drawer runner hardware.
1. Blum Drawer Runner without Blumotion. PN: 562H5330C
2. Blum Locking Device Right Side: PN: T51.1801R
3. Blum Locking Device Left Side: PN: T51.1801L
4. Drawer Shelf Pins
5. Door and Drawer Pulls (you pick)
6. 3/4" Overlay Hinges
Preparation:
To begin this project, you’ll need to take your purchased lumber and cut
out all of the parts listed in Table 2. Plywood parts should be cut to their final size
using a combination of a table saw and a circular saw. Refer to the plywood cut
sheets at the end of these plans
Hardwood components however, should be cut to their final lengths, but
not their final widths. All hardwood boards should be cut slightly wider than their
final width on the table saw then brought down to their final width using a jointer
or thickness planer. If you skip this process and simply cut your hardwood boards
down to their final widths using the table saw you’ll end up with boards that have
a very rough-cut and uneven edge. It won’t look as clean or professional.
Our Home from Scratch LLC Page 7 CabinetsfromScratch.com
TABLE 2: CABINET PARTS LIST
Hardwood Cabinet Parts
Item Name Length (in.) Width (in.) Thk (in.) Qty. Material
1 Stiles 31 2 3/4 2 Oak or Poplar
2 Top Rail 32 2 3/4 1 Oak or Poplar
3 Mid-Rail 32 2 3/4 1 Oak or Poplar
4 Bottom Rail 32 2 3/4 1 Oak or Poplar
5 Vertical Divider 20 2 3/4 1 Oak or Poplar
6 Drawer Front 33-1/2 6-1/2 3/4 1 Oak or Poplar
7 Shelf Front 33-3/4 1 3/4 1 Oak or Poplar
Hardwood Door Parts
Item Name Length (in.) Width (in.) Thk (in.) Qty. Material
8 Door Stiles 21-1/2 2 3/4 4 Oak or Poplar
9 Door Rails 14 2 3/4 4 Oak or Poplar
Cabinet Plywood Parts
Item Name Length (in.) Width (in.) Thk (in.) Qty. Material
10 Sides 34-1/2 23-1/2 3/4 2 Matching Ply
11 Bottom 34-3/4 22-5/8 3/4 1 Matching Ply
12 Back 34-1/2 34-3/4 3/4 1 Matching Ply
13 Shelf 33-3/4 12 3/4 1 Matching Ply
Hardwood Drawer Parts
Item Name Length (in.) Width (in.) Thk (in.) Qty. Material
14 Sides 21 4-1/4 1/2 2 Maple
15 Front 30-9/16 4-1/4 1/2 1 Maple
16 Back 30-9/16 4-1/4 1/2 1 Maple
17 Sides 21 4-1/4 1/2 2 Maple
Plywood Door Parts
Item Name Length (in.) Width (in.) Thk (in.) Qty. Material
18 Door Panel 18 13 1/2 2 Matching Ply
Plywood Drawer Parts
Item Name Length (in.) Width (in.) Thk (in.) Qty. Material 19 Bottom 30-9/16 20-1/4 1/4 1 Birch Ply
Our Home from Scratch LLC Page 8 CabinetsfromScratch.com
Machining:
With all of your lumber cut to their final dimensions, we can begin
machining the lumber to add grooves and pocket screw holes, which will allow us
to assemble the cabinet.
Face Frame
Let’s start with the face frame. Lay out all of your face frame boards down
on a workbench. Evaluate each board to determine which side looks best. Using
a pencil, lightly mark the better side so you know what side is which. Flip all of
the boards over. Drill two pocket screw holes on both ends of the backsides of
the Top Rail, the Middle Rail and the Bottom Rail. Drill one pock screw hole on
the ends of the back of the Vertical Divider.
The stiles then get a ¼” deep by ¾” wide groove down the length of the
back. These grooves will allow the cabinet box to recess and attach to the face
frame during assembly. This groove needs to be located ¼” in from the outside
edge of the stiles.
Figure 1 illustrates what the back of the face frame will look like once
assembled. You don’t need to assemble it at this point.
Our Home from Scratch LLC Page 9 CabinetsfromScratch.com
Figure 1: Face Frame Back with Pocket Screw Holes and Stile Grooves
Doors
Moving onto the doors, you’ll need to expose a ¾” long tongue (or tenon)
at the ends of each door rail. For a clear instruction on how to accomplish this
using a table saw, watch this YouTube video from my channel:
https://www.youtube.com/watch?v=WTwRxyHVHFg
Once the tongues are exposed on the door rails, you can cut a ¼” wide by
¼” deep groove down the middle of each door part. Next, raise the table saw
blade to ¾” high and make a 2-1/2” long groove on the ends of the door stiles.
This will allow the tongues on the rails to plug into the stiles. Test for fit.
For another example of this technique, you can watch this YouTube video
from my channel: https://www.youtube.com/watch?v=VyWnPv8DGx0
At this point, you can cut a ¼” deep by ¼” wide rabbit all along the edge of
the door center panels. You should be able to assemble doors dry without any
glue to test its fit up. Make adjustments where necessary.
Our Home from Scratch LLC Page 10 CabinetsfromScratch.com
Drawers
The drawer front is easy. Once it’s cut to its final dimensions, it’s complete.
For the drawer box, you’ll need to do a little machining. Add ¼” deep by ¼” wide
groove down the length of all four hardwood drawer parts. The bottom edge of
the groove should allow a ½” of remaining material. See Figure 2 for guidance.
This groove will support the drawer bottom once assembled.
Figure 2: Groove in the Drawer Box Sides, Front and Back
Next we’ll need to add notches to both ends of the front and back drawer
box parts. These notches are for the side drawer box boards to sit in. See Figure
3 for guidance. The notches can be made on the table saw. You should dry fit the
drawer parts together to make sure they fit well. Make adjustments as necessary.
Our Home from Scratch LLC Page 11 CabinetsfromScratch.com
Figure 3: Notches for Drawer Box Front and Back Boards
Plywood Boxes
Machining the plywood boxes will require adding 3/4” grooves in a few
places but first we’ll start with the toe kicks. Using a pencil, mark 3-1/2” in from
the bottom and 3-1/2” from the front corner of one of the sides. This box will be
for the toe kick and can be removed using a circular saw and a handsaw. Repeat
this on the other side board.
Next, you’ll need to add a 3/4” wide by 3/8” deep groove 4-1/4” up from
the bottom of one of the sides. A second groove will go down the length of the
side board 1/4” in from the back. These grooves should be located on the inside
facing surface. Repeat these grooves on the other side board, but make them
mirror image to the first. By that I mean you need to have a left and a right box
side and not two lefts or two rights. See Figure 4 for guidance on where to locate
the grooves.
Our Home from Scratch LLC Page 12 CabinetsfromScratch.com
Figure 4: Box Side Board – Left Side
The back board will need one 3/4" wide by 3/8” deep groove 4-1/4” up
from the bottom edge. See Figure 5 for that image. The bottom board won’t
need any modifications.
Our Home from Scratch LLC Page 13 CabinetsfromScratch.com
Figure 5: Back Board
Assembly:
Using wood glue and 1-1/4” long pocket screws, assemble the face frame as
per Figure 1. Make sure the Vertical Divider is located at the midpoint of the
frame.
For the box assembly, dry fit the box components together first before
gluing the assembly together. The sides can be stood upright, while the back is
inserted into the grooves in each side. You can then insert the bottom board into
the grooves in the sides. The bottom board should fully seat into the groove in
the back board and will be 1/4" recessed from the front edges of the sides. Use
clamps to help you keep the assembly together during dry fit. If everything fits
together well without glue, you can disassemble it and glue it together.
Liberally apply a bead of wood glue into each groove before you re-
assemble. You can shoot in a 3/4" long brad nail at an angle into the joints to
Our Home from Scratch LLC Page 14 CabinetsfromScratch.com
keep the assembly together while you are clamping it up. Make sure to clamp the
assembly in multiple spots as you go.
At this point, you can also glue the face frame to the box assembly and
clamp both units together by applying a liberal bead of glue in the face fame
groove. Check to ensure the top of the face frame and the top of the box
assembly are flush. It might help to position the cabinet upside down on a
workbench to ensure they remain flush. Measure the cabinet from diagonal to
diagonal at the top of the cabinet to verify the cabinet is square. If it’s out of
square, use a long clamp over the longer corners and tighten it down until it
comes into square. Keep the cabinet clamped together overnight to make sure
the glue cures properly.
Dry fit and assemble the drawer box in a similar manner. When gluing
together, you don’t need to put glue in the 1/4” groove for the drawer bottom.
The glue should only be applied to where the sides meet the front and back
boards. You’ll also need to use a couple brad nails at each joint to keep it
together. A dovetail joint would be best here, but that’s a more advanced
technique that requires more equipment and training. Instead, these brad nails
and glue should hold up fine under average use.
The doors will go together similarly. Only apply glue to the tongues. You
don’t need to glue the center panel in, but you can if you want to since it’s
plywood. Make sure the stiles ends are flush to the rails and clamp together
overnight.
Once the cabinet has been completely glued up, you can install the drawer
runners to the cabinet and the runner hardware to the drawer boxes. If you’re
using Blum Tandem runners, follow the instructions posted here:
https://www.blum.com/us/en/01/30/10/ - ASSEMBLY0. You’ll need to add
blocking to the inside of the cabinet box near the drawer space to bring the
surface flush with the edges of the face frame. The drawer runners can then be
screwed into that blocking. More detailed instructions can be found at the Blum
link above.
Our Home from Scratch LLC Page 15 CabinetsfromScratch.com
The shelf front board can be attached to the plywood shelf board using glue
and brad nails.
For the door hinges, it’s best to simply follow the manufacturer’s
instructions provided with the hinges you purchase as they vary from
manufacturer to manufacturer. The doors should be installed temporarily to
ensure fit and functionality then removed for finishing.
The drawer front should be attached to the drawer box temporarily using a
clamp to hold it in place. Once it’s positioned correctly, two screws from inside
the cabinet box can be driven into the drawer front. After installation, remove
the drawer front for finishing.
Finishing:
Before painting or staining, sand every surface lightly using 120-grit
sandpaper. Sand every surface again using 220-grit sandpaper and then wipe
clean with a clean rag. You can use a tack cloth and a rag with denatured alcohol
as well.
If you want to paint your cabinet, you should apply two coats of a primer
followed by two coats of your finish paint. It’s best to spray both applications
using an HVLP gun. You can use a shellac-based primer like BIN and a satin
lacquer for the final coat. If spraying your paint is not an option, you can use a
brush to apply your paint. Read more here about best practices and products for
painting cabinets:
http://www.ourhomefromscratch.com/2014/09/cabinet-painting-101/
If you plan to stain your cabinet, apply a pre-stain conditioner first to avoid
blotches. Follow that with your stain and then either a clear coat lacquer as a
topcoat or satin polyurethane. You should generally avoid anything glossier than
satin or eggshell.
Our Home from Scratch LLC Page 16 CabinetsfromScratch.com
For your drawer boxes, don’t paint or stain them. You can apply a few thin
coats of polyurethane to make sure they don’t stain from use.
After the finishing process is complete, you can re-assemble your cabinet
permanently by re-installing the doors and the drawer front.
Resources
That’s it. If you find any errors, have any suggestions for improvement or
any questions, drop me a line at [email protected]
Thanks and good luck!!
Our Home from Scratch LLC Page 17 CabinetsfromScratch.com
4x8 Plywood Panel Cutsheet
Our Home from Scratch LLC Page 18 CabinetsfromScratch.com
2x4 Plywood Panel Cutsheet
Our Home from Scratch LLC Page 19 CabinetsfromScratch.com
1/2” Thick Door Panel Plywood Cutsheet