![Page 1: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/1.jpg)
Lecture 2
• Resistance• Ohm’s Law• Electric Energy • Electric Power• Efficiency
http://dramermejbel.weebly.com
![Page 2: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/2.jpg)
• The common units: Volts, Amps, Ohms, Coulombs are all named after people
Volta Ampere Ohm Coulomb
![Page 3: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/3.jpg)
Resistance
• The resistance of a conductor is due to the collisions between free electrons and atoms.
• When the same voltage is applied across different conductors, different currents flow.
• Some conductors offer more opposition or resistance to the passage of current than others.
![Page 4: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/4.jpg)
Factors Affecting Resistance
1. The length L of the material. Longer materials have greater resistance.
1 W
L
2 W
2L
If the wire doubles in length, it doubles in resistance
![Page 5: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/5.jpg)
2. The cross-sectional area A of the material. Larger areas offer LESS
resistance.
. • Notice that the electrons
seem to be moving at the same speed in each one but there are many more electrons in the larger wire.
• This results in a larger current which leads us to say that the resistance is less in a wire with a larger cross sectional area.
It can be shown thatR1/A.
![Page 6: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/6.jpg)
• For metals and a lot of insulators, when temperature is raised, the lattice ions vibrate more vigorously, increasing the frequency of collision between electrons and the lattice. The resistance therefore increases. T ↑ R↑⇒
3. The higher temperatures result in higher resistances.
![Page 7: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/7.jpg)
4. The kind of material. Iron has more electrical resistance than a geometrically similar copper conductor.
Ig < Is < IcR glass > R steel > R copper
![Page 8: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/8.jpg)
Introductory Circuit Analysis, 12/eBoylestad
Copyright ©2011 by Pearson Education, Inc.publishing as Pearson [imprint]
TYPES OF RESISTORS (Fixed and variable) Fixed Resistors
FIG. 3.13 Fixed-composition resistors: (a) construction; (b) appearance.
![Page 9: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/9.jpg)
Calculating Resistance
• It’s possible to calculate resistance of a resistor using the color bands on it– AB represent a 2 digit number– C represents the magnitude
– Resistance = AB * 10C + D
![Page 10: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/10.jpg)
Example: Calculating Resistance
• The first two bands correspond to 4 and 7. The third band tells you the number of zeros following.
47*103 = 47,000 Ω + 10%
![Page 11: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/11.jpg)
Larger devices have a larger surface area.
A physically larger device is able to dissipate more heat and handle more power.
11
Since a device loses heat through its surface, the larger the surface area, the more heat a device dissipates. Heat dissipation is related to
device surface area.
Copyright © Texas Education Agency, 2013. All rights reserved.
![Page 12: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/12.jpg)
Variable Resistors -- Potentiometers
• is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.
Rac = Rab + Rbc
![Page 13: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/13.jpg)
Construction
![Page 14: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/14.jpg)
Setting the Value of Resistance
EGR 101 14
![Page 15: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/15.jpg)
RheostatsA variable resistance used to control current
Usually a two-terminal variable resistorPotentiometer can be wired as a rheostat
![Page 16: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/16.jpg)
Introductory Circuit Analysis, 12/eBoylestad
Copyright ©2011 by Pearson Education, Inc.publishing as Pearson [imprint]
TEMPERATURE EFFECTS
Demonstrating the effect of a positive temperature coefficient( a-for conductors) and a negative temperature coefficient (b-for semiconductors )on the resistance
![Page 17: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/17.jpg)
Temperature Coefficient
For most materials, the resistance R changes in
proportion to the initial resistance Ro and to the
change in temperature Dt.
0R R t Change in resistance:
The temperature coefficient of resistance, a
is the change in resistance per unit resistance per unit degree change of temperature.
00
1; Units:
C
R
R t
![Page 18: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/18.jpg)
Example : The resistance of a copper wire is 4 mW at 200C. What will be its resistance if heated to 800C? Assume that a = 0.004 /Co.
0 00 ; (0.004 / C )(4 m )(60 C )R R t R
Ro = 4 m ; W Dt = 80oC – 20oC = 60 Co
DR = 1.03 mWDR = 1.03 mW
R = Ro + DR
R = 4 mW + 1.03 mW
R = 5.03 mWR = 5.03 mW
![Page 19: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/19.jpg)
Resistivity of a materialis a measure of how strongly a material opposes the flow of electric current
is called the resistivity of the material.
AR
1 As R and
AR
get We
AR
Hence
The unit of is .m
1 •Conductivity of material , s
![Page 20: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/20.jpg)
Resistivity of various materials
Material Class (.m )
Copper Good conductor 1.72 10-8
Aluminum Good conductor 2.65 10-8
Germanium Semiconductor 0.6
Silicon Semiconductor 2300
Quartz insulator 5 1016
![Page 21: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/21.jpg)
Ohm’s Law Every conversion of energy from one form to
another can be related to this equation.
In electric circuits the effect we are trying to establish is the flow of charge, or current.
The potential difference, or voltage between two points is the cause (“pressure”),
The resistance is the opposition encountered.
![Page 22: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/22.jpg)
Ohm’s Law Developed in 1827 by Georg Simon Ohm
For a fixed resistance, the greater the voltage (or pressure) across a resistor, the more the current.
The more the resistance for the same voltage, the less the current.
Current is proportional to the applied voltage and inversely proportional to the resistance.
![Page 23: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/23.jpg)
Ohm’s Law (Golden Triangle)
; ; V V
I V IR RR I
![Page 24: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/24.jpg)
Plotting Ohm’s Law
![Page 25: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/25.jpg)
Plotting Ohm’s Law
Insert Fig 4.8
![Page 26: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/26.jpg)
Example : When a 3-V battery is connected to a light, a current of 6 mA is observed. What is the resistance of the light filament?
Source of EMF
RI
+ -
V = 3 V6 mA
3.0 V
0.006 A
VR
I
R = 500 WR = 500 W
![Page 27: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/27.jpg)
Copyright © Texas Education Agency, 2011. All rights reserved. 27
In this first example, we will calculate the amount of current (I) in
a circuit, given values of voltage (E) and resistance (R):
What is the amount of current (I) in this circuit?
![Page 28: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/28.jpg)
Copyright © Texas Education Agency, 2011. All rights reserved. 28
In the last example, we will calculate the amount of voltage supplied by a
battery, given values of current (I) and resistance (R):
What is the amount of voltage provided by the battery?
![Page 29: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/29.jpg)
Energy
Energy (W ) lost or gained by any system is determined by:
W = P×t
Since power is measured in watts (or joules per second) and time in seconds, the unit of energy is the wattsecond (Ws) or joule (J)
![Page 30: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/30.jpg)
Power Power is an indication of how much work (the
conversion of energy from one form to another) can be done in a specific amount of time; that is, a rate of doing work.
• Power is the rate of doing work– Power = Work / time
• Power is measured in watts (W)• Work and energy measured in joules (J)• One watt = One joule per second
![Page 31: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/31.jpg)
Power in Electrical Systems
• From V = W /Q → W = V × Q• and I = Q / t → Q = I× t • W = V× I × t , P = W / t• P = V× I × t / t → P = V× I • From Ohm’s Law ( I = V / R ), we can
also find that
P = I 2 R and P = V 2 / R
![Page 32: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/32.jpg)
32
Power in Electrical Systems
• We should be able to use any of the power equations to solve for V, I, or R if P is given
• For example:
PRV
R
PI
![Page 33: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/33.jpg)
Diagnosis and Troubleshooting of Automotive Electrical,Electronic, and Computer Systems, Fifth EditionBy James D. Halderman
© 2010 Pearson Higher Education, Inc.Pearson Prentice Hall - Upper Saddle River, NJ 07458
WATT’S LAW ( Magic Circle )
![Page 34: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/34.jpg)
Efficiency Efficiency () of a system is determined by the
following equation:
= Po / Pi
Where: = efficiency , (η is Greek letter eta) Po = power output
Pi = power input
- Poor efficiency in energy transfers results in wasted energy , generates more heat .
- Heat must be removed (requires fans and heat sinks)
![Page 35: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/35.jpg)
Efficiency
• To find the total efficiency of a system–Obtain product of individual efficiencies
of all subsystems:
Total = 1 × 2 × 3 × ∙∙∙
![Page 36: Lecture 2 Resistance Ohm’s Law Electric Energy Electric Power Efficiency](https://reader035.vdocuments.net/reader035/viewer/2022062409/56649d315503460f94a09fc7/html5/thumbnails/36.jpg)
EfficiencyThe basic components of a generating (voltage) system
are depicted below, each component has an associated efficiency, resulting in a loss of power through each stage.
Insert Fig 4.19