Logitech Extreme 3D Pro Main Joystick SpringReplacement
This guide will assist you in replacing the main joystick spring on a Logitech Extreme 3D Pro.
Written By: Emanuel Canela
Logitech Extreme 3D Pro Main Joystick Spring Replacement Draft: 2018-06-26Guide ID: 106455 -
This document was generated on 2019-09-20 06:13:17 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 8
INTRODUCTION
When moving the joystick, the main spring bends. The spring also keeps the joystick upright. Aftertime, the spring can cause the joystick to sag when not in use. In this situation, replacing the springwill be necessary.
TOOLS:Phillips #1 Screwdriver (1)
Logitech Extreme 3D Pro Main Joystick Spring Replacement Draft: 2018-06-26Guide ID: 106455 -
This document was generated on 2019-09-20 06:13:17 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 8
Step 1 — Disassembly of the handle
Remove these three Phillips #1screws:
Two 10mm screws.
One 7mm screw.
Step 2
Using your fingers, lower the rubberboot to reveal two screwsunderneath the joystick.
Remove the two 10mm Phillips #1screws.
Logitech Extreme 3D Pro Main Joystick Spring Replacement Draft: 2018-06-26Guide ID: 106455 -
This document was generated on 2019-09-20 06:13:17 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 8
Step 3
Pull apart the joystick chassis by hand.
Release this clip located underneath the hand rest
The circuit board will be loose and may fall down.
Step 4 — Disassembly of the base
Remove the eight 10mm Phillips #1screws from the bottom.
Logitech Extreme 3D Pro Main Joystick Spring Replacement Draft: 2018-06-26Guide ID: 106455 -
This document was generated on 2019-09-20 06:13:17 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 8
Step 5
Flip the joystick upright.
Lift up the sliver base cover and feed the loose circuit board through.
Careful with the wires still attached to the silver base cover from the bottom of the joystick.
Step 6 — Main Joystick Spring
Disconnect the wire from the motherboard.
Logitech Extreme 3D Pro Main Joystick Spring Replacement Draft: 2018-06-26Guide ID: 106455 -
This document was generated on 2019-09-20 06:13:17 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 8
Step 7
Remove this plug from the motherboard.
Step 8
Remove the four 10mm Phillips #1 screws from the joystick base.
Logitech Extreme 3D Pro Main Joystick Spring Replacement Draft: 2018-06-26Guide ID: 106455 -
This document was generated on 2019-09-20 06:13:17 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 8
Step 9
Remove the joystick assembly.
Step 10
Remove the white plastic piece ontop of the spring.
The white plastic will be covered in alubricant.
Logitech Extreme 3D Pro Main Joystick Spring Replacement Draft: 2018-06-26Guide ID: 106455 -
This document was generated on 2019-09-20 06:13:17 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 7 of 8
To reassemble your device, follow these instructions in reverse order.
Step 11
Remove the Spring
The spring will be covered inlubricant.
Logitech Extreme 3D Pro Main Joystick Spring Replacement Draft: 2018-06-26Guide ID: 106455 -
This document was generated on 2019-09-20 06:13:17 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 8 of 8