-
(A
Ins
F
Fire AAS724
stallat
Fire
Alarm40 – 2
tion, Op
MA
eFi
m Con2 & 4
Comperat
AN299
ind
ntrol / AS4
mmisstion
94-4
der
Pane4428
sionin
PL
el - 3)
ng &
LUSS
-
Acce
The indicaZone
Acce
If a nresou Note:“Next
the a
ess Level 1
ator will alsoes in alarm ar
Tpf
ess Level 2 c A
new alarm isund.
: If Delays tot” button and
larms the PR
Tfa Ws
1
i be illuminatre displayed
FIRST A D.DSC: Z.DCS:LAST AL D.DSC: Z.DCS:PRESS PAC:2Z
This control panel buzzerfire alarm is a
2 – Default A
When the acontrol will si
Activating the
s recognised
o Outputs had “Enter” butt
REVIOUS an
A Zone or Dthe Disable
Note: The Ausing this bu
This control ault indicator
When using tsilenced first
Resp
indicator wilted if a Zoneon the LCD
ALARM: L1 D:Loop 1 Sen:Zone 1 LARM: L4 D4:Loop 4 Sen:Zone 5 DepPREVIOUS/NE ALM:5
is used to sr, which soua steady sou
Access level
alarm devicelence all alar
e control aga
d whilst the
ve been conon.
PreLCDsele Whmu
nd NEXT con
Device can bbutton.
Alarm conditutton to disab
is used to rer.
the Reset buby means of
FIRE B
ponding
ll be illumine Board is ins
as follows.
D1 Z1 nsor 1
49 Z5 nsor 49 pend C
NEXT TO VIE PALM:0
silence the londs whenev
und where as
when the do
es are activerms excludin
ain, will resou
alarm devic
nfigured, to in
evious and ND. The eveected view, i
hen the “SEVltiple fire ala
ntrols are use
be disabled w
tion takes pble faults.
eset the FAC
utton to cleaf Alarms Sile
BRIGADE RFIRE BR
g to a Fi
nated. The astalled otherw
W OTHER ALFLT:0 D
ocal buzzer. ver there is as for a fault it
oor is opened
e (FACP is ng the Extern
und the prev
ces are “sile
nvestigate th
Next controlsents being de Zone Mod
VERAL ALAarms are preed.
when in an A
precedence a
CP from the f
r a fire condence / Resou
RESPONSRIGADE RE
re
applicable zwise details
15:31
15:31
ARMS IS:0
Pressing thia fire alarm o
is intermitte
d.
in the fire cnal Alarm dev
iously silence
enced”, then
he delayed A
s are used todisplayed dee or Device M
ARMS” indicaesent on the
Alarm or Fau
and no alarm
fire condition
ition, alarm dnd control.
SE GUIDE ESPONSE G
zone of the Loop,
is button wilor fault. The
ent.
condition), acvice.
ced alarm dev
all alarm d
Alarm conditio
o scroll the eepends on Mode.
ator is illumFACP. In o
ult condition
ms must be
n and to clea
devices mus
GUIDE
Sensor and
l silence thesound for a
ctivating this
vices.
devices shall
on press the
vents on thethe current
inated, thenorder to view
by pressing
e present for
r the system
st have been
d
e a
s
l
e
e t
n w
g
r
m
n
-
FIRE BRIGADE RESPONSE GUIDE
FIRE BRIGADE RESPONSE GUIDE
Disabling a Zone / Device Access Level 2 The following methods can be used to DISABLE a ZONE or Device: For Zones:
Press then Press for Zone 1 selection.
FIREFINDER 17/10/2013 09:00:00 ZONE:1 SELECT ZONE NO. THEN TO OR DISPLAY OR ZONE/DEVICE DISABLE/ENABLE KEY AC:2Z ALM:0 PALM:0 FLT:0 DIS:0
Now Press the . For Devices:
Press the then enter Loop number, Press then enter device number.
FIREFINDER 17/10/2013 09:00:00 LOOP:1 DEVICE:1 SELECT DEVICE NO. THEN TO OR DISPLAY OR ZONE/DEVICE DISABLE/ENABLE KEY AC:2Z ALM:0 PALM:0 FLT:0 DIS:0
Now Press the .
In either case the Disable LED will illuminate and the screen will display the disabled information
Loop 1 Sensor 1 MCP L1 D1 Z1 STAT:NORMAL /DISB ZONES DISABLES 1 of 1 AC:2Z ALM:0 PALM:0 FLT:0 DIS:1
-
TABLE OF CONTENTS Section Page No. 1 About This Manual ............................................................................................................ 1
1.1 Introduction .......................................................................................................... 1 1.2 General Requirements ......................................................................................... 1 1.3 References .......................................................................................................... 1 1.4 Symbols ............................................................................................................... 1
2 Introduction ....................................................................................................................... 2 2.1 System Overview ................................................................................................. 2 2.2 Key Features ....................................................................................................... 2 2.3 Compliance .......................................................................................................... 3 2.4 FACP Configuration Examples ............................................................................ 4
3 FireFinder PLUS Description ........................................................................................... 5 4 Placing The Basic System Into Operation ...................................................................... 7
4.1 Unpacking ............................................................................................................ 7 4.2 Anti-Static Precautions ........................................................................................ 7 4.3 Working on the System ........................................................................................ 7 4.4 The Cabinet ......................................................................................................... 7 4.5 Cabling Recommendations.................................................................................. 8 4.6 Power Supplies and AC Mains Installation ........................................................ 10
4.6.1 Connecting the Mains Earth ............................................................... 10 4.6.2 Connecting 5 AMP Power Supply ...................................................... 10
4.7 CORRECT Power Up / Turn “ON” Procedure ................................................... 11 4.8 Brigade / PSU Monitor Board ............................................................................ 11
4.8.1 Battery Connections ........................................................................... 13 4.8.2 Auxiliary 27 Volt Power ...................................................................... 13 4.8.3 Monitored Inputs ................................................................................. 14 4.8.4 Monitored Outputs .............................................................................. 15 4.8.5 Relay Output Connections ................................................................. 16
4.10 Main Board ........................................................................................................ 18 4.11 Front Panel Board .............................................................................................. 19 4.12 Main CPU........................................................................................................... 20 4.13 Slave CPU ......................................................................................................... 21 4.14 Addressable Dual Loop Termination Board....................................................... 22
4.14.1 Detector loop Isolator Installation ....................................................... 23 4.14.2 Loop Isolator calculator ...................................................................... 23 4.14.3 Loop Open / Short Circuit. .................................................................. 23
5 FireFinder PLUS Control Panel ..................................................................................... 24 5.1 System Controls ................................................................................................ 24 5.2 System Indicators .............................................................................................. 28
6 Functions And Menus ..................................................................................................... 31 6.1 The Default LCD Display ................................................................................... 31 6.2 LCD Contrast ..................................................................................................... 31 6.3 Accessing Functions and Menus ....................................................................... 31 6.4 Function Menu and Access Levels .................................................................... 32
6.4.1 Forgotten Passwords ......................................................................... 32 7 The Main Menu ................................................................................................................ 33
7.1 Alarms ................................................................................................................ 33 7.2 Stage 1 Alarms .................................................................................................. 33 7.3 Pre-Alarms ......................................................................................................... 34 7.4 Faults ................................................................................................................. 34 7.5 Disables ............................................................................................................. 35 7.6 Walk Tests ......................................................................................................... 35 7.7 Status ................................................................................................................. 36
-
7.8 Tools .................................................................................................................. 40 7.9 Setup .................................................................................................................. 41 7.10 About .................................................................................................................. 42
8 The Function Menu ......................................................................................................... 43 8.1 Date ................................................................................................................... 43 8.2 Time ................................................................................................................... 43 8.3 Day/Night ........................................................................................................... 44 8.4 Logs ................................................................................................................... 44 8.5 TESTS ............................................................................................................... 45 8.6 I/O ...................................................................................................................... 46 8.7 Global (Network Panels) .................................................................................... 47 8.8 Passwords (Level III) ......................................................................................... 48 8.9 Programming ..................................................................................................... 49
8.9.1 Conv (Conventional) Zone ................................................................. 49 8.9.2 Device ................................................................................................. 50 8.9.3 Input .................................................................................................... 51 8.9.4 Output ................................................................................................. 51 8.9.5 Panel Based MCP .............................................................................. 51 8.9.6 Sub Address ....................................................................................... 51 8.9.7 Zone programming ............................................................................. 51 8.9.8 Extra Devices Detected ...................................................................... 53 8.9.9 Mismatch Detected ............................................................................. 53
9 Incoming Fire Alarm Signal............................................................................................ 54 10 Accessing a Loop, Device or Zone ............................................................................... 55 11 Modem / Programming / Debug Interfacing ................................................................. 56 12 Expanding the FACP with Compatible FireFinder PLUS Boards ............................... 57
12.1 Ancillary Services .............................................................................................. 57 12.2 Compatible FireFinder PLUS Boards ................................................................ 57 12.3 Expansion Board ............................................................................................... 58 12.4 8 Zone Conventional Board ............................................................................... 59 12.5 32 Zone Alarm Mimic Card ................................................................................ 60 12.6 8 Way Switch and Indicator Card ...................................................................... 61 12.7 16 Way Input Board ........................................................................................... 62 12.8 8 Way Relay Board ............................................................................................ 63
12.8.1 Internal Relay Board ........................................................................... 63 12.8.2 Remote Relay Board .......................................................................... 64
12.9 8 Way Sounder Board ....................................................................................... 65 12.10 4 Way Fire Fan Module ..................................................................................... 66 12.11 4 Way Fan Termination Board ........................................................................... 67 12.12 Bargraph Display Card ...................................................................................... 68
12.12.1 Mechanical ......................................................................................... 68 12.12.2 Front Panel Decal ............................................................................... 68 12.12.3 Front Panel Controls .......................................................................... 68
12.13 Communications Extender Board ...................................................................... 69 12.14 SmartTerminal ................................................................................................... 69
12.14.1 Overview ............................................................................................ 69 12.14.2 Mechanical ......................................................................................... 70 12.14.3 Installation & Cabling .......................................................................... 71 12.14.4 Setting the SmartTerminal Address ................................................... 71 12.14.5 Operation ............................................................................................ 72 12.14.6 SmartTerminal Controls and Indicators .............................................. 73 12.14.7 SmartTerminal Screen Format ........................................................... 73
12.15 Agent Release Control ....................................................................................... 76 12.15.1 Operation ............................................................................................ 76 12.15.2 Agent Release Module ....................................................................... 79 12.15.3 Local Control Station .......................................................................... 80 12.15.4 Agent Release Termination Board ..................................................... 83
-
12.15.5 Interface Wiring .................................................................................. 84 12.15.6 Warning Signs .................................................................................... 85
12.16 Occupant Warning Systems .............................................................................. 89 12.16.1 Amplifier Board (25W and 50W) ........................................................ 89 12.16.2 Front Panel Switch and Indicator Module .......................................... 90 12.16.3 Panel Interfacing ................................................................................ 91
12.17 Printer ................................................................................................................ 92 12.17.1 Indicators and Buttons ........................................................................ 92 12.17.2 Maintenance ....................................................................................... 93 12.17.3 Printer Connections and Jumpering ................................................... 95 12.17.4 Printer 5 Volt Power Supply ............................................................... 95
13 Expanding the System through Networking ................................................................ 96 13.1 Networking ......................................................................................................... 96 13.2 Network Interface Card ...................................................................................... 96 13.3 High Level Interface Expander .......................................................................... 98
14 Certification Information .............................................................................................. 100 15 Maintenance and Troubleshooting Chart ................................................................... 101
15.1 Maintenance .................................................................................................... 101 15.2 Troubleshooting FireFinder PLUS ................................................................... 102
16 Compatible Devices ...................................................................................................... 103 17 Address Setting ............................................................................................................. 105 18 Glossary of Terms ......................................................................................................... 106 19 Definitions ...................................................................................................................... 107 20 Specifications ................................................................................................................ 108 21 QUICK REFERENCE GUIDE ......................................................................................... 110 22 Statement of Compliance ............................................................................................. 111
22.1 Installation Details ............................................................................................ 113 23 Commissioning Test Report ........................................................................................ 114
23.1 Procedure ........................................................................................................ 115 23.2 System Information .......................................................................................... 115
-
FIREFI
1 Abou1.1 This PLUSin its 1.2 The compcomp
1.3 Conf ApolAmp AustAS72AS72AS44 1.4
N
NDER PLUS
ut This MIntrod
manual contS Fire Alarminstallation,
GenerFireFinder
ponents so promised in a
Be qualified
Be familiar of a FireFin
Observe an
Be aware tparameters
ReferefigManager P
lo: ac:
ralian Stand240 - 2: 2004240 - 4: 2004428 - 3: 2010
Symbo
Note:
S (AUST)
Manual uction tains all the Control Pancommissioni
ral RequirePLUS FACPas to comp
any way insta
d and trained
r with the connder PLUS c
nti-static pre-
that if a probs of the insta
ences PLUS: Ope
Det Pro
dard: 4 Con4 Pow0 Fire
ols Important o
Configuratio
Obs
Mains supp
DA
INSTALLA
information nel (FACP) aing and oper
ements P has been ply with majallation staff
d for the task
ntents of thiscontrol syste
-cautions at a
blem is encoallation the su
eration Manu
tector / Devicoduct Data S
ntrol and Indwer Supply Ee Brigade Pa
perational in
on considera
serve antista
ply earth
NGER mains
Page
ATION,COMM
required to and is only avration.
designed aajor world st
and operato
k they undert
s manual prioem;
all times; and
untered or thupplier shoul
ual
ce Manualsheets
icating EquipEquipment anel
nformation
ations
atic precautio
s supply pres
1
MISSIONING
install, commvailable to a
and manufactandards. To
ors should;
take;
or to the inst
d
here is any dd be contact
pment
ons
sent
G OPERATIO
mission and nd for the us
ctured from o ensure th
tallation, com
doubt with reted.
ON
operate these of person
high quality hese standa
mmissioning
espect to the
e FireFindernel engaged
commercialards are not
or operation
e operational
r d
l t
n
l
-
Page 2
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
2 Introduction 2.1 System Overview The purpose of the FireFinder PLUS Fire Alarm Control Panel (FACP) is to monitor changes in inputs, report those changes and update selected outputs as programmed. 2.2 Key Features The FireFinder PLUS panel is capable of supporting:
Apollo Discovery and XP95 Intelligent Detectors, Multisensor, Photoelectric, Ionisation, Thermal (heat) and CO detectors.
Conventional two wire zone detector circuits Multiple input/outputs Agent Release Fan Control High Level Interfaces SmartGraphics EV3000 – Early Warning System Nurse Call SmartTerminal Remote LED mimics Peer to Peer networking Master Slave (Main - Sub) networking Main panel plus Data Gathering Panels networking
Figure 1: Typical Application
-
Page 3
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION 2.3 Compliance
The FireFinder PLUS FACP is approved to AS7240 – 2 & 4 and AS4428 – 3:2010 and includes the following ‘Optional requirements’ as defined by AS7240-2:2004:
7.8 Output to fire alarm devices
7.9.1 Output to fire alarm routing equipment
7.9.2 Input from fire alarm routing equipment
7.10.1 Output type A to fire protection equipment
7.11.1 Delays to outputs – configuration of delays (for item C)
7.11.2 Delays to outputs – control of delays (for item C)
7.12.1 Dependency Type A
7.12.2 Dependency Type B
7.12.3 Dependency Type C
9.3 Fault signals from points
9.9 Output to fault warning routing equipment
10 Disable condition
10.5 Disablement of addressable points
11 Test condition
ZB Alarm Acknowledgement Facility
ZD Ancillary Control function
The FireFinder PLUS PSE includes the following ‘Optional requirement’ as defined by AS7240-4:2004:
5.5 Battery function check
-
Page 4
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
2.4 FACP Configuration Examples
CN3
TB1
TB2
CN
1
TB3
+27V
0V TR
X+
TRX-
SCR
N
CO
M
TXD
RXD
RTS
CTS
OU
T
COMMS IN COMMS OUT+ - S C B AD+ - S C B AD C
OM
TXD
RXD
RTS
CTS TB3
CN1 CN2
TB2TB1
OPTIONAL NETWORKING BOARDSNETWORK INTERFACE CARDNOTE: POSITION MAY VARY AS SHOWN AND IS FOR INDICATION ONLY.
TYPICAL FRONT DOOR LAYOUT FOR A FULLY POPULATED PANEL
NOTE: PANEL LAYOUT MAY VARY DEPENDING ON CLIENT CONFIGURATION
MAIN CONTROL BOARD
FRONT PANEL CONTROL
CN
21
CN20
TH1CN8
CN1
CN6
D13
D14C
N3
C12
BZ1CN5
CN2
CN7
CN11
CH16CH15
CH6 CH8
CH2CH1
CN16
CN14
CN18
R17
TP3
RN17RN20
CN4
CN10
CN15
CN13
CN17
cba
4 3 2
BRIGADE I/F
FRONT PANELEXPANSION LEDSEXPANSION PANEL
MODEM
27V
IN
PRINTER
PSU MONITOR
LOO
P C
OMM
S
1
+
CN1
CN2
1
SLAV
E CP
U
CH8
CN1
CN2
1
CH8
CN1
CN2
1
SLAV
E CP
U
SLAV
E CP
U
U15
CN2
a b c
U11
U10
U14
U13
CPU
BOAR
D
PRINTER PSUC/W CABLE
+ -
BRIGADEO/P TERMBOARD
EARTH STUD
MAINSSWITCH
POWERSUPPLYUNIT
CABINET BACKPAN VIEWSHOWING MODULES FITTEDTO THE BACKPANAND WIRING DETAILS
TO BATTERIES
DANGER240V
CN1CN3
2 LOOP TERMINATION BOARD
L2+ L1-B
L2+ L1-A
EXT+35V
EXT+35V
L2+ L1-B
L2+ L1-A
EXT+35V
EXT+35V
SERIAL RELAYBRD ORAGENT TERM BRDORFAN TERM BRD
POWERCN4CN2 TX1
POW
ER
ZD7
CN2
CN1
CN3
L(AC) N(AC) -V -V +V +V(AC)
ACTI
VE
NEUT
RAL
GRO
UND
-VE
HPCI
SGD
AU
X O
UT
1A
UX
OU
T 2
+-
N/C
CN
/ON
/O
E. BOARD CONTROL
BAT+BAT- +27V0VE. BOARD SW. POWER
CN
1 TB
10
CN
3
REL
AY 4
N/C
CN
/ON
/CC
N/O
N/C
CN
/OR
ELA
Y 3
REL
AY 2
REL
AY 1
+-
POWERO/Ps
+VE
TO CN11BRIGADE O/P BRD
20 WAY
3 WAY
16 WAY
26 WAY
X- PRINTERC/W MOUNTINGPLATE.
FAN CONTROL,AGENT RELEASE, OWS CONTROL ORSWITCH & INDICATOR
Figure 2: Typical Example of a SP1M/SP1X Layout
FRONT DOOR AND FRONT INNER DOOR REAR VIEW SHOWINGINSTALLED BOARDS ON FRONT INNER DOOR AND WIRING DETAILS
CABINET BACKPAN VIEWSHOWING MODULES FITTED TO THE BACKPANAND WIRING DETAILS
BRIGADEPSU MON.BOARD
MAIN CONTROL BOARD
FRONT PANEL CONTROL
TO BATTERIES
2 LOOP TERMINATION BOARD OR16Z CONVENTIONAL BOARD
CN8
CN1
CN6
CN5
CN7
CH15
CH2
CN10
BRIGADE I/F
PRINTER
PSU MONITOR
BLANK
SLAV
E CP
U 4
EARTH STUD
EXPANSION BOARD
TB1TB2
CN2
CN1
TB3
CTS
RTS
RXD
TXD
COM
DA
BC
S-
+D
AB
CS
-+
COM
MS O
UTC
OMM
S IN
OUT
CTS
RTS
RXD
TXD
COM
SCRN
TRX-
TRX+
0V
+27V
TB3
CN1
TB2
TB1
CN3
OPTIONAL NETWORKING BOARDSNETWORK INTERFACE CARDCONTROLLER INTERFACE CARD.NOTE: POSITION MAY VARY ASSHOWN AND IS FOR INDICATIONONLY.NETWORK
I/F CARD
SLAV
E CP
U 3
SLAV
E CP
U 2
SLAVE CPU6
NOTE: WIRING MAY VARY DUE TOCLIENT PANEL CONFIGURATION
CH15
CONTROLLERI/F CARD
CPU
BOAR
D
SLAVE CPU7
SLAVE CPU8
MAINSINPUT
16Z
CO
NVEN
TIO
NAL
BOAR
D
CABINET
L(AC) N(AC) -V -V +V +V(AC)
POWERSUPPLYUNIT
ANCILLARIES or HOUSING BLANKS
AGENT RELEASEMODULE ORFIRE FAN CONTROLMODULE
CN1CN3
AGENT TERMBRD ORFAN TERMBRD
ZD7
CN2
MAINSSWITCH
DANGER240V
GENERALINDICATORCARD
BLANK
SLAVE CPU5
HPCI
POWER OK
SGD
AUX
OU
T 1
AUX
OU
T 2
+-
N/C
CN/
ON/
CC
N/O
1+1-
2+2-
3+3-
4+4-
2+3+
4+C
E. BOARD CONTROL
COM
MS.
COM
MS.
BAT+BAT- +27V0V
COMMS FAIL
1+
E. BOARD SW. POWER
CN
11C
N10
CN1 T
B10
CN3
CN10RS485
COMMS.IN
CN11RS485
COMMS.OUT
RELA
Y 4
RELA
Y 5
MO
NITO
RED
OUTP
UTS
N/C
CN/
ON/
CC
N/O
N/C
CN/
ORE
LAY
3RE
LAY
2RE
LAY
1+
-
POWERO/Ps
BATT
MO
NITO
RED
INPU
TS
20 WAY
10 WAY
3 WAY
3 WAY
20 WAY
16 WAY
ACTI
VENE
UTRA
LG
ROUN
D
-VE
+VE
TO CN11BRIGADEO/P BRD
RJ45/8 PIN
X- PRINTERC/W MOUNTINGPLATE.
Figure 3: Typical Example of a SP8 Layout
-
Page 5
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
3 FireFinder PLUS Description The following description does not relate to specific cabinets as the size of each cabinet will vary with the amount of hardware fitted. The heart of the FireFinder PLUS consists of two boards collectively known as the Controller. These boards are the Main Board and the CPU Board. Combining these two boards with a front panel forms the basis for a FireFinder PLUS FACP. A single Controller without an expansion board has the capacity to interface to four (4) Slave CPU’s modules. These Slave CPU’s can be used for Loop Termination Boards. The Main Board has the Slave CPU Board for the first Loop Termination Board and the provision for mounting of up to three additional Slave CPU’s to interface to loops 2 - 4. The Slave CPU’s all have the same software installed and the manner in which they operate is automatically determined by the type of termination or interface board onto which they connect. If the system is to be expanded to have more than four Loop’s an Expansion Board is required. This board contains Slave CPU No. 5 and expansion sockets for three more to interface to loops 6 - 8. This configuration allows for a maximum number of 8 Slave CPU’s that any one Controller can accommodate.
OUTBUZZERINHIBIT
BUZZERRS485 EOL+5V
0V
PRINTER 27V
TER
MIN
ATI
ON
BO
AR
D1
NO
DE
AD
DR
ESS
NET
WO
RK
LO
OP
CO
MM
SPS
U M
ON
ITO
R
PRINTER
RESET
27V
IN
COMMS1RS232/MODEM (BOTTOM) EXPANSION PANEL EXPANSION LEDS
FRONT PANEL
BRIG
ADE
I/F
234
BACKLIGHT
EXPA
NSI
ON
EXTRA CONTROLS
KEY SWITCH
EXPANSION
SLAVE 2SLAVE 3SLAVE 4
MODULE
MO
DU
LE
COMMS2 RS232 (TOP)
RS232COMMS 2
CN
26
CN8
CN27
CN11
CN23
CN17
CN13 CN15
CN
10
CN4
87
65
43
21
SW2
CN
18
CN14
CN9
CN16
CN
7
CN2CN5
+ BZ1
SW1
CN3CN1
LK3
CN20
LK2
CN6
CN100
DE
BU
G
CN
2
LK1
TP1
76 8
CN
5
CN1CN2 CN3 CN4
DE
BU
G
CN
2
LK1
TP1
DE
BU
G
CN
2
LK1
TP1
DE
BU
G
CN
2
LK1
TP1
DE
BU
G
CN
2
LK1
TP1
DE
BU
G
CN
2
LK1
TP1
MAIN BOARD
MAIN CPU
SLAVE CPU 4 SLAVE CPU 3 SLAVE CPU 2
SLAVE CPU 6 SLAVE CPU 7 SLAVE CPU 8
RS485 COMMS TO BACKPAN BOARDS
LOOP COMMSEXTERNAL LOOPCOMMUNICATIONCONNECTS TO NIC
NODE ADDRESS
THE MAIN BOARDIS FITTED WITHSLAVE CPU 1CN10 TO LOOPTERMINATION BRD
27VDC IN
INTERNAL PRINTERO/P
TO FRONT KEYPAD(NOT USED IF THE PANEL IS A NODE WITHIN THE SAME PANEL)
KEYSWITCHAND EXTRACONTROLSINTERNAL SERIAL
COMMS PORTEXPANSION LED'S (CN3)
RS485 COMMS TO FRONT DOOR BRDS
CN21
AN EXPANSION BOARD (BRD86FEPB) CAN BE CONNECTEDTO FACILITATE UP TO FOUR ADDITIONAL SLAVE CPU'S IF REQ
SLAVE CPU 5ON BOARD
20 WAYRIBBON
USB
CN25
USBDEBUG
COMMS 3
Figure 4: Single Controller Board with Expansion Board
-
Page 6
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION FireFinder PLUS has an internal RS485 communication bus that allows for various ancillary boards (add on modules) to be connect to the panel. These boards can be used to control and monitor field plant equipment or the addition of an agent release module. Where the system design exceeds the capability of one FireFinder PLUS then other FireFinder PLUS panels can be networked together to provide an expanded system containing multiple boards in a variety of applications. Some of these applications include:
A Master / Slave (Main Sub) FACP arrangement (MFACP / SFACP) A Peer to Peer System Use of Data Gathering Panels (DGP’s) SmartTerminal SmartGraphics
A Network FireFinder PLUS System supports a combination or all these options on a single network. Each panel on the network is regarded as a “node”. The NETWORK BUS is accessed using a Network Interface Card (BRD86NIC). The network configuration determines whether a NIC is required. Configurations can be; Master / Sub FACP: Where there is one or more FACP’s configured as local panels then each report the status of their associated zones/devices to a MFACP. There is no control between local panels as the MFACP is structured to have full control of the entire system. Peer to Peer: Each FACP user can take control of the entire fire system from any FACP. Data Gathering Panel: The use of this type of panel may be installed where there is a need to have field terminations only at one location and all control is performed by an FACP that is remotely located. SmartTerminal: Provide the user with the ability to monitor the status of designated areas or an entire site as well as execute specific interrogation tasks. SmartGraphics: Is an active graphics system connected to the FireFinder PLUS.
-
FIREFI
4 Plac4.1 Caref The p
4.2 To prwhile 4.3 or reto pr 4.4 Feat
Openbottodevic
NDER PLUS
ing The Unpac
fully unpack
package sho FireF A CD 003
Anti-Srevent dama
e performing
WorkiPrior to
placing anyrevent dama
The Ctures: The
eithe Norm The
allow Knoc
cabin
Note: It is re
n the front dom of the un
ces are broug
Fig
S (AUST)
Basic Sycking the FireFind
ould include: Finder PLUSD containing keys
Static Precage to compoany task with
ng on the o unplugginy module or age to panel
abinet
cabinet is aer surface or mally paintedinner and ou
w the doors ockouts are pnet to simplif
ecommended
oor. Use thenit to mount ght in throug
gure 5: Exam
INSTALLA
ystem In
der PLUS.
S Fire Alarmthis “Installa
cautions onents, modhin the FACP
System g any conneboard, ensu
l componen
available in fflush mounte
d Surf Mist Ruter door hinopen to an anpositioned onfy cable entry
d the cabinet
e keyhole moit on the w
h the knocko
mple SP1 Ba
Page 7
ATION,COMM
to Opera
Control Panation and Com
dules and boP. The same
ector, connure that botts.
four differened. With flus
Ripple. Other nges are mongle of 100º.n gland platey. Mounting
t should be i
ounting holeswall. Cables outs on the to
ck Pan Moun
7
MISSIONING
ation
nel mmissioning
oards, anti-ste applies to th
ecting or dith the Mains
nt styles. Eash mounting tcolours are
ounted on the A keyed enes and a cuThe Cabinet
installed in a
s in the top cto connect top or bottom
R 6mm
Tap lightly arim of the kn
nting Hole &
G OPERATIO
” manual
atic precautihose situated
sconnectings and Batter
ch style hasthough a suravailable on e left-hand stry is providet out is avai
t
clean, dry, v
corners and the system t of the cabin
m.
around thenockout
Removing K
ON
ions MUST bd in the field.
g any wiringries have be
s the capabirround is reqrequest.
side of the caed ilable on the
vibration-free
the two holeto its extern
net.
12 mm
R 3 m
Knockouts
be observed.
g, removingeen isolated
ility of beinguired.
abinet which
e rear of the
e area.
es along thenal actuating
m
d
g d
g
h
e
e g
-
Page 8
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.5 Cabling Recommendations Conventional Zones Cabled in red Twin Plastic Sheath (TPS), Fire rated Radox or approved equivalent. Analogue Loop Two core cable. The minimum cable size is 0.75mm2, the maximum loop resistance is 50 ohms and the maximum loop distance is 2km. RS 485 Network Single twisted pair screened (2 core) cable originating from FACP extending through the protected areas and returning to the FACP. Cable Specifications Capacitance of 100 Pico farads per metre or less Resistance of 100 milliohms per metre or less Impedance of loop typical 100 to 120 ohms Maximum distances between modules 1.2km providing cable meets above specifications. Recommended cable type Belden 8132 or 9842 (non fire rated) Radox FR Communication 0.75mm 1 pair (fire rated) x 2 SmartTerminal Single twisted pair shielded cable (2 core) plus 2 core power, or local supply. Maximum distance between from the last SmartTerminal and the FACP is 1.2km. LED Mimic (RS485) Single twisted shielded cable (No return loop) plus 2 core power or local supply. Maximum distance between each LED repeater card and FACP is 1.2km. Recommended Cable Type Hartland HC2335 Belden 9841 Radox FR Communication Fire Alarm Bell Connection Two core 1.5mm2 PVC sheathed MIMS (Mineral Insulated Metal Sheathed) to the bell location. Brigade Connection via Telecom Two core 1.5mm² PVC sheathed MIMS from the FACP to the Telecom MDF. RJ45 Multi-drop Serial Port 8 core Flat cable Power Supplies / AC Mains The requirement for the mains supply to the FACP is fixed wiring, using three core cable (no less than 0.75mm² and no more than 2.5mm² ) or a suitable three conductor system, fed from an isolating switch fuse spur, fused at 3A. This should be secured from unauthorised operation and be marked 'FIRE ALARM: DO NOT SWITCH OFF. The Mains supply must be exclusive to the FACP.
-
FIREFI
withotighte
CommSwitchHigh eUniverShort cBuilt in Input VInput PFC PowerType N PSU18PSU18330-00
NDER PLUS
out the Poweened.
mon Power Sh Mode Desigefficiency, lowrsal AC inputcircuit/ over ln EMI Filter a
Voltage: 8Freq 4
0
r Supply SpNo
888 890 015
S (AUST)
Important: er Supply PC
Supply Featgn w working temt/ full range load and PFC Circ
85 to 264 VA47 to 63Hz. 0.95~230VAC
ecificationsOutput 27V @ 5.624V @ 14A27VDC @
INSTALLA
Under no CB correctly
tures & Spec
mp.
cuit
AC
C
s To
6A 1A 122A 1
Page 9
ATION,COMM
circumstancmounted in
cificationsOveHigSoftRemOve ToleLoaLine
olerance
1% 1% 1%
9
MISSIONING
ces should tthe enclosur
er voltage proh efficiency; t start with limmote control er temp. prot
erance at 27ad Regulatioe Regulation
R & N 150mV150mV240mV
G OPERATIO
the FireFindre and the re
otection low ripple nomiting AC suon/off (optioection (optio
7V +/on +/n +/
V V V
ON
der PLUS betaining scre
oise urge current n)
on)
/- 1% /- 0.5% /- 0.5%
Efficiency 84% 87% 86%
be operatedews securely
y
d y
-
Page 10
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.6 Power Supplies and AC Mains Installation Generally the AC Mains will be connected to either a 5 Amp, 14Amp or 22 Amp 27 volt supply. These supplies will be either mounted in the upper or lower right hand corner of the cabinet with the Brigade Board mounted in close proximity. The wiring should enter the cabinet through the nearest knockout entry hole on that side. Refer to Figures 6 - on for the wiring and fusing details for each supply. 4.6.1 Connecting the Mains Earth All earth cabling shall be terminated to the panel Chassis Earth Terminal in a star configuration. The earth cable closest to the cabinet body shall have an M4 SPW beneath the lug then an M4 SPW and M4 nut. Each additional earth cable shall be terminated with an M4 SPW and M4 nut. An additional M4 nut and M4 SPW are fitted to the Chassis Earth Terminal for installers to connect their Mains Earth.
M4 Shake Proof Washer
M4 Shake Proof Washer
CHASSIS EARTH TERMINAL
M4 Nut
Earth Cable
Earth Cable
M4 NutM4 Shake Proof Washer *
M4 Nut *Note:
* Extra M4 Nut and M4 SPW are provided finger tight on the Earth bolt.
Figure 6: Panel Earthing
4.6.2 Connecting 5 AMP Power Supply Output Voltage: 27.4 Volts. FUSE Rating: 2 Amp 3AG Slow Blow Mains Cable: should be no less than 0.75mm²
Figure 7: Mains Power Connection to the 5 AMP Power Supply
-
Page 11
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.7 CORRECT Power Up / Turn “ON” Procedure Once all the field devices are installed and the wiring has been correctly terminated the FireFinder PLUS is ready to turn on. For reliable power up it is essential the following procedure be followed;
1. Turn the Mains power on, THEN 2. Connect the batteries observing correct polarity. 3. The green power on LED should be illuminated.
4.8 Brigade / PSU Monitor Board The Brigade / PSU Monitor Board (BRD86BPSC) monitors and controls the power supply, battery charging, monitored / un-monitored inputs, outputs and the 5 relay outputs.
Connections TB(x) Function Type of Output TB1 Aux Out x 2 Protected TB2 Relay 1 1 Amp Voltage Free Contacts TB3 Relay 2 1 Amp Voltage Free Contacts TB4 Relay 3 1 Amp Voltage Free Contacts TB5 Relay 4 1 Amp Voltage Free Contacts TB6 Relay 5 1 Amp Voltage Free Contacts TB7 Monitored Outputs x 4 24Vdc EOL TB8 Monitored Inputs x 4 Switched Negative, EOL TB9 Battery Out / 27VDC PSU IN Protected TB10 External Board / SW POWER CN(x) Function Type of Output CN1 JTAG CN1 SGD CN3 External Board Controls CN4-8 Power Out 1 Amp ( protected )
Relay Information Voltage Free contacts are rated at 1A @ 30V Back EMF Protection Inductive loads fitted to the Brigade PSU Monitor Board MUST be fitted with “Flyback” diodes at the load for back EMF protection. Transient Protection Recognised transient line protection methodologies at the FACP and the load MUST be considered when connecting any control devices to the outputs be they in close or remote.
-
Page 12
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
IsolateRelay
AlarmRelay
Batt Fail Relay(NormallyEnergised)
FaultRelay
To CN20 of the MainController Board
CN4 to 8 SuppliesRegulated +27VDC to Internal Boards 1A / Connector
+27VDCfrom PSU
Note: N/C C N/O Denotes Voltage Free ContactsN/C = Normally ClosedC = CommonN/O = Normally Open
( EOL Required )
C
N/C
N/O
EOL10KOhms
WarningSystemAlarm
Battery 2 12Volts
Battery 1 12 Volts
+-
-+
Bell
Note:If a diode is NOT fittedinternally to a bell / soundera diode MUST be fitted asshown - fit 1N4004 or similar
2 x AUX OUT27VDC @ 2A
HPCI
EOL10KOhms
Sounder
( EOL's Required )
POWER OK
22/0
9/09
SGD
AU
X O
UT
1A
UX
OU
T 2
+-
N/C
CN
/ON
/CC
N/O
1+1-
2+2-
3+3-
4+4-
2+3+
4+C
JTAG
E. BOARD CONTROL
CO
MM
S.C
OM
MS.
ETH
BAT+BAT- +27V0V
COMMS FAIL
EO
L
1+
E. BOARD SW. POWER
BRD
86B
PSC
4-
EXT
TEM
P
L9
R10
3R
108
C36
C34
C35
C56 C58
CN4
CN5
CN6
CN7
CN
11C
N10
CN
1
CN2
D9
D10
D11
D7
LK1
M2
M11
M1
M4
M12
M3
M6
M13
M5
M8
M14
M7
M10
M15
M9
Q5
R75
RL1
RL2
RL3
RL4
RL5
TB1
TB9
TB8
TB7
TB2
TB3
TB4
TB5
TB6
TH4
TH2
TH1
TH7
TH8
U2
U8
U5
U6
U7
ZD8
ZD5
ZD4
ZD1
ZD6
ZD2
ZD7
ZD3
TB10
HSNK2
CN
3
N12
36
L6
L7L8
C43
CN12
1T1
Q8
TH5
HSN
K1
TH9
CN8
M16
CN10RS485
COMMS.IN
CN11RS485
COMMS.OUT
Relays are ProgrammableDefault SetupShown
MONITORED INPUTS
MONITORED OUTPUTS
REL
AY
4R
ELAY
5M
ON
ITO
RED
OU
TPU
TSN
/CC
N/O
N/C
CN
/ON
/CC
N/O
REL
AY
3RE
LAY
2R
ELAY
1
AUX OUT 1
AUX OUT 2
+-
POWERO/Ps
BATTFLT.
MO
N E
N
MO
NIT
OR
ED IN
PUTS
Figure 8: Brigade / PSU Monitor Board Layout
Note: When connecting to the Brigade PSU Monitor board transient and “Flyback” (Back EMF) protection methodologies MUST be applied.
-
Page 13
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.8.1 Battery Connections A FireFinder PLUS requires two (2) 12 volt batteries (TB9). The batteries should be placed into the bottom right hand side of the cabinet. A red and black lead coming from TB1 on the Brigade Board will be clearly seen in the same area, this lead is to be connected to the batteries red to positive and black to negative once the system is operating on Mains supply. Battery size is dependent on the system configuration and can vary from 12 AHr to over 100 AHr.
Note: Refer to Ampac’s battery calculation tool to calculate the required battery size.
TB9 is located on the bottomright hand side of the board
+27VDCfrom PSU
Battery 2 12Volts
Battery 1 12 Volts
+-
-+
HPCI
POWER OK
22/0
9/09
SGD
AUX
OU
T 1
AUX
OU
T 2
+-
N/C
CN
/ON
/CC
N/O
1+1-
2+2-
3+3-
4+4-
2+3+
4+C
JTAG
E. BOARD CONTROL
CO
MM
S.C
OM
MS
.
ETH
BAT+BAT- +27V0 V
COMMS FAIL
EO
L
1+
E. BOARD SW. POWER
BRD
86BP
SC4-
EX
T TE
MP
L9
R10
3R
108
C36
C34
C35
C56
C58
CN4
CN5
CN6
CN7
CN
11C
N10
CN
1
CN2
D9
D10
D11
D7
LK1
M2
M11
M1
M4
M12
M3
M6
M13
M5
M8
M14
M7
M10
M15
M9
Q5
R75
RL1
RL2
RL3
RL4
RL5
TB1
TB8
TB7
TB2
TB3
TB4
TB5
TB6
TH4
TH2
TH1
TH7
TH8
U2
U8
U5
U6
U7
ZD8
ZD5
ZD4
ZD1
ZD6
ZD2
ZD7
ZD3
TB10
HSNK2
CN
3
N12
36
L6
L7L8
C43
CN12
1T1
Q8
TH5
HS
NK
1
TH9
CN8
M16
CN10RS485
COMMS.I N
CN11RS485
COMMS.OU T
RELA
Y 4
REL
AY 5
MO
NIT
OR
ED O
UTP
UTS
N/C
CN
/ON
/CC
N/O
N/C
CN
/ORE
LAY
3RE
LAY
2RE
LAY
1+
-
POWERO/Ps
BATTFLT.
MO
N E
N
MO
NIT
OR
ED IN
PUTS
+27VDCfrom PSU
Battery 2 12Volts
Battery 1 12 Volts
+- -+ TB9
+ +- -
BAT+BAT- +27V0V
TB9
BRIGADE BOARD
Figure 9: Battery Connections to the Brigade / PSU Monitor Board
4.8.2 Auxiliary 27 Volt Power Two (2) 1 Amp outputs are available from TB1 terminals 1+ (plus) and 2- (minus) or 3+ and 4- on the Brigade Board. It is important to note these outputs are short circuit monitored.
TB1 is located in the lowerleft hand side of the board
TB1
+ -
+ -
AUX OUT 1
AUX OUT 2 2 X LIMITED 2AAUX POWEROUTPUTS
POWER OK
22/0
9/09
SGD
AUX
OU
T 1
AUX
OU
T 2
+-
N/C
CN/
ON/
CC
N/O
1+1-
2+2-
3+3-
4+4-
2+3+
4+C
JTAG
E. BOARD CONTROL
COM
MS.
COM
MS.
ETH
BAT+BAT- +27V0V
COMMS FAIL
EOL
1+
E. BOARD SW. POWER
BRD8
6BPS
C4-
EXT
TEM
P
L9
R10
3R
108
C36
C34
C35
C56 C58
CN4
CN5
CN6
CN7
CN
11C
N10
CN2
D9
D10
D11
D7
LK1
M2
M11
M1
M4
M12
M3
M6
M13
M5
M8
M14
M7
M10
M15
M9
Q5
R75
RL1
RL2
RL3
RL4
RL5
TB8
TB7
TB2
TB3
TB4
TB5
TB6
TH4
TH2
TH1
TH7
TH8
U2
U8
U5
U6
U7
ZD8
ZD5
ZD4
ZD1
ZD6
ZD2
ZD7
ZD3
TB10
HSNK2
CN
3
N123
6
L6
L7L8
C43
CN12
1T1
Q8
TH5
HSN
K1
TH9
CN8
M16
CN10RS485
COMMS.IN
CN11RS485
COMMS.OUT
RELA
Y 4
RELA
Y 5
MON
ITOR
ED O
UTPU
TSN/
CC
N/O
N/C
CN/
ON/
CC
N/O
RELA
Y 3
RELA
Y 2
RELA
Y 1
+-
POWERO/Ps
BATTFLT.
MON
EN
MON
ITOR
ED IN
PUTS
BRIGADE BOARD
CN
1TB
1
+27VDCfrom PSU
Battery 2 12Volts
Battery 1 12 Volts
+-
-+
HPCI
Figure 10: Auxiliary 27VDC Power Output
-
Page 14
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.8.3 Monitored Inputs Four independently monitored inputs (TB8) are provided and can be configured for a variety of uses.
Manual Call Point (MCP) – if activated the FACP will go into alarm. Connected to the MCP on the front of the FACP.
Class Change – if activated all Alarm Devices/Sounders and Alarm Device/Sounder Outputs in Sounder Group 1 are turned on.
External Fault – if activated the FACP will indicate a Fault condition Ancillary Disable - if activated, the FACP’s “DISABLED” and ANC OUTPUT STATUS LEDs
will both be turned on. Note that this event is used to indicate an ancillary/auxiliary disablement or a door-opened condition if a door switch is fitted. It also activates any Relays on the Brigade board configured as “Isolate” relays and affects the Brigade Board’s “Aux/Anc” outputs based on their “normally energised” settings.
Evacuate – if activated the FACP goes into Evacuation. Sounder Silence – if activated all activated sounders are silenced. Reset – if activated a Master Reset is initiated. Fire/Feedback - if activated, the FACP’s “Fire Output On” LED will flash (AS7240.2 Clause
7.9.2). Note that this is a latched condition and will only be cleared a “Master Reset” command from the FACP.
General Purpose – for use in Functions (Cause and Effects) The default configuration types for the inputs are as follows:
Input 1 – MCP Input 2 – Evacuate Input 3 – External Fault Input 4 – Reset
The inputs have been designed to operate with a programmable EOL of 3K3Ω, 10KΩ 22KΩ or Unmonitored (no EOL) the 10K EOL is the default. The normal and active ranges change according to the end of line selected.
Line Resistance (10K EOL) Sensed Condition 0Ω– 150Ω Short circuit Fault 470Ω – 4KΩ Active condition 8KΩ – 15KΩ Normal 20KΩ to ∞ Open circuit Fault
Door Switch TB11
EOL10KOhms
DBA / MCP
4K7
Note: Door Switch is Open for Normal Operation and not Monitored
TB8
TB8 location
C 1
+ 2
+ 3
+ 4
+
TB8 / C
TB8 / 1+, 2+, 3+ or 4+(EOL depends on config)
TB8 / 1+, 2+, 3+ or 4+(Config set to "unmonitored")
TB8 / CTO
TO
POWER OK
22/0
9/09
SGD
AUX
OU
T 1
AUX
OU
T 2
+-
N/C
CN/
ON/
CC
N/O
1+1-
2+2-
3+3-
4+4-
2+3+
4+C
JTAG
E. BOARD CONTROL
COM
MS.
COMM
S.
ETH
BAT+BAT- +27V0V
COMMS FAIL
EOL
1+
E. BOARD SW. POWER
BRD8
6BPS
C4-
EXT
TEM
P
L9
R10
3R
108
C36
C34
C35
C56 C5
8
CN4
CN5
CN6
CN7
CN1
1C
N10
CN2
D9
D10
D11
D7
LK1
M2
M11
M1
M4
M12
M3
M6
M13
M5
M8
M14
M7
M10
M15
M9
Q5
R75
RL1
RL2
RL3
RL4
RL5
TB7
TB2
TB3
TB4
TB5
TB6
TH4
TH2
TH1
TH7
TH8
U2
U8
U5
U6
U7
ZD8
ZD5
ZD4
ZD1
ZD6
ZD2
ZD7
ZD3
TB10
HSNK2
CN3
N123
6
L6
L7L8
C43
CN12
1T1
Q8
TH5
HSN
K1
TH9
CN8
M16
CN10RS485
COMMS.IN
CN11RS485
COMMS.OUT
RELA
Y 4
RELA
Y 5
MON
ITOR
ED O
UTPU
TSN/
CC
N/O
N/C
CN/
ON/
CC
N/O
RELA
Y 3
RELA
Y 2
RELA
Y 1
+-
POWERO/Ps
BATTFLT.
MON
EN
MON
ITOR
ED IN
PUTS
BRIGADE BOARD
CN1
TB1
+27VDCfrom PSU
Battery 2 12Volts
Battery 1 12 Volts
+-
-+
HPCI
TB8
Figure 11: Inputs DBA / MCP and Door Switch Wiring
-
Page 15
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.8.4 Monitored Outputs Four independently monitored and controlled outputs (TB7) are provided and can be configured for a variety of uses.
Alarm Devices - activated when any of its four sounder groups is active. (AS7240.2 Clause 7.7 and 7.8). The output is turned off during an Alarm (sounder) disable or Alarm (sounder) silence condition.
ASE – (Australia Firefinder Plus Only) Fire/FARE – activated by alarm condition (AS7240.2 Clause 7.7 and 7.9.1). The output is
turned off during a FIRE disable condition. Ancillary - activated on device alarm conditions. The Output is turned off during an Ancillary
disable condition. Warning System - activated on evacuation and device alarm conditions. The output is
turned off during an Alarm (sounder) disable or Alarm (sounder) silence condition. Fault - activated on all fault conditions (AS7240.2 Clause 9.9). The output is turned off
during a FAULT disable condition. General Purpose – activated via the Configmanager “Function” programmed logic. External Alarm Devices - activated by an Alarm condition when a Point (Detector) has
been configured as Fire/FARE. (AS7240.2 Clause 7.7 and 7.8). The output is turned off by the removal of the alarm condition – Silence Alarms followed by Reset.
These monitored switched outputs, supply a nominal 24VDC, at up to 1 Amperes. Monitoring is for short, open and earth faults when the output is OFF. The outputs have been designed to operate with a programmable EOL of 3K3Ω, 10KΩ 22KΩ or Unmonitored (no EOL) the 10K EOL is the default.
Line Impedance (10K EOL) Reported Condition 0Ω– 50Ω Short circuit Fault 50Ω – 150Ω Indeterminate: Maybe reported as shorted or normal 150Ω – 15KΩ Normal 15KΩ – 40KΩ Indeterminate: Maybe reported as normal or open circuit 40KΩ to ∞ Open circuit Fault
Warning systems and sounders are connected to the Brigade / PSU Monitor Board as shown below. If more sounders are required, the Sounder / Bell Control Board must be used.
SounderTB7EOL10KOhms
1+
1-
TB7 Location
+ / - are monitored 1A outputs. Un-used O/P'smust be terminated in 10K Ohms EOL
Note: If a diode is NOT fitted internally to a bell / sounder a diode MUST be fitted asshown - fit 1N4004 or similar
EOL10KOhms
2+
2-3+
3-
4+
4-
Bell
Warning System
+27VDCfrom PSU
Battery 2 12Volts
Battery 1 12 Volts
+- -+
HPCI
POWER OK
22/0
9/09
SGD
AU
X O
UT
1A
UX
OU
T 2
+-
N/C
CN
/ON
/CC
N/O
1+1-
2+2-
3+3-
4+4-
2+3+
4+C
JTAG
E. BOARD CONTROL
CO
MM
S.C
OM
MS.
ETH
BAT+BAT- +27V0V
COMMS FAIL
EO
L
1+
E. BOARD SW. POWER
BR
D86
BPSC
4-
EXT
TEM
P
L9
R10
3R
108
C36
C34
C35
C56 C58
CN4
CN5
CN6
CN7
CN
11C
N10
CN2
D9
D10
D11
D7
LK1
M2
M11
M1
M4
M12
M3
M6
M13
M5
M8
M14
M7
M10
M15
M9
Q5
R75
RL1
RL2
RL3
RL4
RL5
TB2
TB3
TB4
TB5
TB6
TH4
TH2
TH1
TH7
TH8
U2
U8
U5
U6
U7
ZD8
ZD5
ZD4
ZD1
ZD6
ZD2
ZD7
ZD3
TB10
HSNK2
CN
3
N12
36
L6
L7L8
C43
CN12
1T1
Q8
TH5
HSN
K1
TH9
CN8
M16
CN10RS485
COMMS.IN
CN11RS485
COMMS.O UT
RELA
Y 4
REL
AY 5
MO
NIT
OR
ED O
UTP
UTS
N/C
CN
/ON
/CC
N/O
N/C
CN
/OR
ELAY
3R
ELAY
2RE
LAY
1+
-
POWERO/Ps
BATTFLT.
MO
N E
N
MO
NIT
ORE
D IN
PUTS
BRIGADE BOARD
CN
1TB
1TB
8TB
7
Figure 12 Connecting a Bell / Sounders
-
Page 16
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.8.5 Relay Output Connections Five “voltage free” relay outputs (TB2 – TB6) are provided and can be configured for a variety of uses.
Alarm - activated on device alarm conditions and “Function” programmed logics. The relay is turned off during a ALARM disable condition.
Sprinkler - activated on device alarm conditions and “Function” programmed logics. Fault - activated on all fault conditions and “Function” programmed logics. The relay is
turned off during a FAULT disable condition. Isolate - activated on all isolate conditions and “Function” programmed logics. Battery Fail - activated on battery fail conditions and “Function” programmed logics. Mains Fail - activated on a mains power fail condition and “Function” programmed logics. Warning System - activated on evacuation, device alarm conditions and “Function”
programmed logics. If the activation of this relay is due to an evacuation condition, then the relay is turned off during an Alarm (sounder) disable or Alarm (sounder) silence condition.
Ancillary - activated on device alarm conditions. General Purpose - activated via “Function” programmed logics
Relay Switching Characteristics These outputs have been designed to be able to switch predominately resistive loads as listed below.
Switching voltage Maximum switching current 30VDC 1A 24VAC 1A 50VDC 250mA 40VAC 250mA
The default relay contacts are connected as shown below.
TB2 TB3 TB4 TB5 TB6TB2 to TB6 are located on thelower to mid left hand side of the board
C NC
NO
1A Un-monitoredVoltage Free Conacts:NO: Normally OpenNC: Normally ClosedC: Common
NO C NCNO C NCNO C NCNO C NC NO C NC NO C NC NO C NC
Note:
NO C NCNO C NC
FIRE FAULT EWIS ISOLATE BATTFAIL
Relays are Programmable. Default Setup Shown
+27VDCfrom PSU
Battery 2 12Volts
Battery 1 12 Volts
+-
-+
HPCI
POWER OK
22/0
9/09
SGD
AU
X O
UT
1A
UX
OU
T 2
+-
N/C
CN
/ON
/CC
N/O
1+1-
2+2-
3+3-
4+4-
2+3+
4+C
JTAG
E. BOARD CONTROL
CO
MM
S.C
OM
MS.
ETH
BAT+BAT- +27V0V
COMMS FAIL
EO
L
1+
E. BOARD SW. POWER
BR
D86
BP
SC4-
EX
T TE
MP
L9
R10
3R
108
C36
C34
C35
C56 C58
CN4
CN5
CN6
CN7C
N11
CN
10
CN2
D9
D10
D11
D7
LK1
M2
M11
M1
M4
M12
M3
M6
M13
M5
M8
M14
M7
M10
M15
M9
Q5
R75
RL1
RL2
RL3
RL4
RL5
TB2
TB3
TB5
TH4
TH2
TH1
TH7
TH8
U2
U8
U5
U6
U7
ZD8
ZD5
ZD4
ZD1
ZD6
ZD2
ZD7
ZD3
TB10
HSNK2
CN
3
N12
36
L6
L7L8
C43
CN12
1T1Q
8
TH5
HSN
K1
TH9
CN8
M16
CN10RS485
CO MMS.I N
CN11RS485
COMMS.O UT
REL
AY 4
REL
AY 5
MO
NIT
OR
ED O
UTP
UTS
N/C
CN
/ON
/CC
N/O
N/C
CN
/OR
ELA
Y 3
REL
AY
2R
ELA
Y 1
+-
POWERO/Ps
BATTFLT.
MO
N E
N
MO
NIT
OR
ED IN
PUTS
BRIGADE BOARD
CN
1TB
1TB
8TB
7TB
4TB
6
Figure 13: Relay Outputs
-
Page 17
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.9 High Current Interface Board
When the 14Amp power supply is used in the FACP the High Current Interface Board is required to provide protection for the boards, cards and other 27VDC distribution within the FACP. The board plugs/connects into the Brigade / PSU Monitor Board (BRD86BPSC) and the 27V DC output from the PSU is connected to TB1 of the BRD86HCI instead of TB9 on the BRD86BPSC
Figure 14: High Current Interface Board
Connections TB Function 1 27VDC PSU IN 2 Battery Out 3 27VDC Out 4 27VDC Out 9 Battery Out / 27VDC PSU IN 10 External Board / SW POWER CN Function 1 - 5
27VDC 3A Max
-
Page 18
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION 4.10 Main Board The Main Board (BRD86MBA) carries the devices for interconnecting to all the other Boards, a buzzer for auditory indication, the backlight power supply for the LCD and CPU Reset. The Main CPU is mounted on this board and connected to it by CN11. The main connection board then provides interfacing to:
Up to 3 Slave CPU’s (Slave CPU 1 is onboard) A printer A Modem An Expansion Panel An Internal serial bus An External communication bus.
Connections CN1 Extra Control (Not Fitted) CN15 Slave CPU connection CN2 Expansion Panel CN16 Printer 27VDC Out CN3 Expansion LED’s (Not Fitted) CN17 To LCD Backlight supply CN4 Front Keypad CN18 External Loop Communication CN5 Printer CN19 LCD Characters CN6 Key Switch (Not Fitted) CN20 RS485 Communications Port 1 CN7 Brigade Output CN21 RS485 Communications Port 2 CN8 Modem and RS232 Comms CN22 To LCD Backlight supply CN9 Ext Buzzer Output (Not Fitted) CN23 Slave CPU Debug (Not Fitted)
CN10 Slave CPU output 1 CN24 Jtag Programming Slave CPU1 (Not Fitted) CN11 Main CPU CN25 USB Programming CN12 LCD Graphic CN26 27VDC In CN13 Slave CPU connection CN27 Comms 2 RS232 CN14 Slave CPU connection CN28 27VDC In (not fitted)
OUTBUZZER
INHIBITBUZZER
RS485 EOL+5V
0V
PRINTER 27V
SLAVE 1
USB
DEBUG
JTAG
DEBUG
TER
MIN
ATIO
N BO
ARD
1
NO
DE
AD
DR
ESS
NET
WO
RK L
OO
P C
OM
MS
PSU
MO
NIT
OR
PRINTER
CN12
RESET
27V
IN
COMMS1 RS232/MODEM (BOTTOM)
EXPANSION PANEL EXPANSION LEDS FRONT PANEL
BRIG
ADE
I/F
234
BACKLIGHT
CN19
EXPA
NSI
ON
EXTRA CONTROLS
KEY SWITCH
SLAVE 2SLAVE 3SLAVE 4
MODULE
MO
DU
LE
BRD86MBA4- 30/06/10
LCD BACKLIGHT INVERTER
COMMS2 RS232 (TOP)
RS232COMMS 227V IN
BACKLIGHT
GRAPH LCD
CH
AR
LCD
CHINESE
NO
N-C
HIN
ES
EG
RAPH
LCD
C91
RN19
RN18
RN17
RN16
R67
CN
26
C90
C89
CN8
U36
U35
R66
R65
R64
R63
R62
Q8
Q6
CN27
C88
C87C86
C85
R4
CN11
ZDN2
ZDN1
U28
R51
R52
R53
R28
R24
R17
R22
R21
R50
R49
R39
R18
R40
R37 R38
R35 R36
R33
R19
R34
Q2
LK1
CN24
CN23
C12
C15
C13
C50
C77
C75C73
C55
C51
CN17
U10
U16
R16
R12
R15
R9
C78
C76
CN13 CN15
CN4RN10RN9
RN
3
RN
7
R59
R60
RN
48
76
54
32
1
SW2
Q3
Q1
R10
R5
C61
U24
U32
U34
C19
C53
C11
C28
C10
C71
C24
R31
R48
R47
R46
R41
R45
R44
R43
R42
C27
C65C66
C62 C63
C58
C26
C69
C56
C39
C52
C59
C68
C45C44 C43
C38
C49
R27
R23
R30
R25
C21
C70
CN18
RN15
RN2
RN14RN13RN12
R29
C72
C33
C34
CN14
CN9
C29
R20
X1
U26
U6U5
U18
U15
U12
U23
U19
U27
RN8
D7
Q4
Q5
CN2
+ BZ1
U17
U22
SW1
U13
U33U31
RN11
C79
D13
D14
D10
D11
D17
D12
D15
D16
C23
C30
C32
C57
C42
C74
C37
C18
U4
C9
C64
C40
CN3
C46
U14
C25
C35
D5
U21
C48C47
C60
U25
C67
D6
U29
C36
C31
C83
R26
C81
C80
D8
U20
D4
R32
RN6
CN1
RN5
C41
U9
C5
C16
LK3
R14
R8
R11
U11
U30
C1
L2
C84
C54
C2
C3C7
C4
C6 D1
L1
R6
R1
R3
R7
R13
U1
R61
C20
C17
C22
CN20
D3D2
R56
RN1
TH1
U8
U3
U2
U7
CN21C82
LK2
TP5
TP3
TP6
TP4
N1236
C8
C14
D9
R58
R54
R57
R55
R2HY1
CN28
CN12
CN
19
CN100
CN22
TP69
CN26
CN10
CN7
CN5
CN16CN6
CN25
EXPANSION
Figure 15: Main Board Layout with no Main CPU or Slave CPU’s
-
Page 19
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.11 Front Panel Board The Front Panel Board (BRD86FPB) provides the buttons used to control the FACP as well as all LED indications. All LED’s are surface mounted and the buttons are embedded within the board. The LCD is viewed / protected by a clear Perspex screen. Connections
CN2 To CN4 Main Board
KEYSWITCH
BRD86FPB4-
11/08/10
KEYSWITCH
U8
R47
R46
R45
R44
R43R42R41
L8
L7 L6L5 L4
D28
C23
C22
C21C20
C19
CN1U1
R21
R20
R22
R19R18R17
R15
R16
R10
R11
R12
R13
R14
Q2
D15C2
R9D9
N1236 U3
U7
U5
U4 U6
U2
R30
R28
R27
R25
R24
R31
R26
R40
R39
R38
R37
R35
R34
R8
R32
R7
R6
R5
R4
R3
R2
R1
R33
Q1
L3L2L1
D2
D20
D1
D11D12
D13
D10
D16
D19
D27
D26
D25
D24
D22
D21
D8
D7
D6
D5
D4
D3
D18
C11
C8
C6
C15C5
C3
C17
C9 C10C12C7
C13
C14 C16
C4
CN2
D14 D23R23 R36
C1 C18
D17R29
D30 R50
Figure 16: Front Panel Board
-
Page 20
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.12 Main CPU The Main CPU (BRD86MCPU) holds the main central processing unit including the Application software and Configuration settings for the FACP.
The Main CPU is a 4-layer surface mount board The processor runs at 60MHz. 16Mbytes of FLASH 32/64 Mbytes SDRAM
Connections
CN1 USB CN2 To Main Board CN11
0V
USB
R30
U11
U6
C45
R25
U4
C32
C20
C31
C17
C27
C10
C4
C7
C11
+
C44
C15
C14
C1
C6
C5
C9
C36
C30
C43
C13C12
C26C25C24
C19
C40
C41
C42
C35
C21
C18
C16
C8
C2
C23
C38
C39
C22
C33
C28
C29
CN1
D2
D1
D4
D3
Q3
Q1
Q2
R2
R14
R1
R22
R24
R18
R17
R19
R15
R13R
6
R11
R4
R8
R9
R3
R10
R12
R26
R27
R7
R5
U5
U13
U3U2
U14U15
U10U9
U16
U7
U12
U8
U1
X1
X2
ZDN
3
ZDN1
ZDN
2
CN2
R16
C3
C37
C34R
20
R21
R23
R28R
29
Figure 17: The Main CPU Board PCB Layout
-
Page 21
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.13 Slave CPU The Slave CPU (BRD86SCPU) provides the interfacing signals and I/O’s required to allow the FACP to connect / communicate to a variety of termination boards. A single chip micro controller U7 controls all operations of the FACP Slave CPU. This device contains the control program within Read Only Memory (ROM). Automatic Termination Board Sensing A unique feature of the Slave CPU is its ability to automatically sense the type of board it is connected to without the user having to configure the board to suit. Connections
CN2 To Loop Termination Board CN3 To Main Control Board
BRD86SCB3-
JTAG
DEBUG
COMMS Q2
R25
R6
C1
C36
C13
C6C2
C34
C14
C10
C15
C37
C11
C16 C
17C
18
C5
C19
C20 C
21
C23
C3
C31
C8
C32
C9
C4
C33
C27
C7
C35
C12
CN2
CN
1D
1
U2
LK1
Q1
R4
R1
R14
R8
R7
R13
R11
R5
R2
R10
R12
R24
RN1
TP2
TP5
TP3
TP4
TP1U7
U6
U3U1
U5
U4
X1
R26R27D2
D3
CN3
CN4
Figure 18: Slave CPU Board
-
Page 22
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.14 Addressable Dual Loop Termination Board The Addressable Dual Loop Termination Board (BRD86DLTB) acts as the interface between the external addressable devices and the control and monitoring functions of the FireFinder PLUS. Each board provides terminations for two loops and can be used with the Apollo range of detectors. One slave CPU is required per loop.
Note: Apollo devices L2 is +ve (positive), L1 is -ve (negative) AMPAC strongly recommend that the LoopManager test set is used to check that the Apollo loop has been correctly installed and commissioned before connecting it to the FireFinder PLUS. Loop Parameters
126 Apollo Devices (i.e. maximum address range) When using Alarm Acknowledgement Facility’s (AAF’s) a max of 50 per Loop 500mA Current Max S/C protection circuitry activates at approximately 650mA Maximum length 1.2km
Note: To achieve full current, the Loop Trip current in Loop Parameters needs to be set to 300mA (ConfigManager PLUS) CONNECTIONS
CN1 / 2 To Slave CPU Board CN3 / 4 27VDC in / out TB1 / 2 To Addressable loop devices
REGULATED27VDC In / Out
T0 SLAVE CPUCN1
R+L1
L2
-R
L1
L2-R
L1
L2-R
R+
R+
Wiring Shown Above is for aXP95 Circuit
with one DetectorHaving LEDMonitoring
L1
L1
L1
L2
L2
L2
INOUT
IN
OUT
BRD86DLTB2-
LOOP 2
LOOP 1
+
-
-
+
+
-
IN
OUT
-
+
+
-
D C+
-
D C
OUT
IN
LOO
P 1
CO
NTR
OL
LOO
P 2
CO
NTR
OL
-5V
+5V
+12V
+40V
0V
LOOP 1 RETURN SENSE
LOOP 2 RETURN SENSE
TRI WAVE
POWER
OUT
OUTLOOP2
INLOOP2
C52
C50
R100
R92
R76
R67
R43
R34
R23
R12
R13
8
R148R142
R13
5
R146R140
R51
R81
R50
R10
4
R103
R10
8
R10
6
R5
R56R55
R54R52
Q26
Q10
Q17Q15
Q18
Q13Q11
Q2
Q8
Q6
Q9
Q4
Q1
D12
D13
D6D5
C17
C41
C97
N1236
R84
R10
5R
4
R127
R12
5
R155
R13
7
R12
3
R15
9
R149
R15
1
R16
0
R16
6
R16
5
R16
4
Q19
Q23
Q21
D19
D15
C65
C49
C76
C54
C61
C87
C77
C82
C75
C90C
89
C100
C94
U1
U8
U21
U22
R18
4
R17
9R17
8
R17
5R17
3
R174
R17
7
R176
C96
C109
C10
8
C10
2
C106
C10
1
C95
U23
ZD23
ZD17
ZD21ZD22
ZD20
ZD13
ZD16
ZD18
ZD15
ZD14
ZD12
ZD6
ZD10
ZD11
ZD9
ZD2
ZD4
ZD7
ZD5
U9
U7
U12
U10
U5
U14
U16
U20
U3
U2
U19
U6
U4
U13
U15
U18
U17
U24 U25
TH2
TH1
TH3
TB2
TB1
RN1
R139
R62
R63
R71
R85
R57
R83
R119
R61
R86
R11
3
R87
R93
R89
R114
R12
2
R77
R12
1
R12
0
R13
4
R66
R64
R97
R143
R15
8
R16
8
R110
R16
7
R147
R136
R2
R3
R9
R37
R30
R11
1R
38
R115
R39
R40
R11
8
R112
R20
R11
6
R11
7
R131
R13
3
R44
R141
R157
R16
3
R109
R16
2
R145
R181R180
R18
2
R18
3
Q16
Q28
Q7
Q27
L4
L3
L6
L8
L2
L1
L5L7
L9
D14
D17
D7
D1
D16
D22
D21
CN3 CN4
CN2CN1
C26
C46
C2
C21
C70
C31
C39
C48
C38
C45
C35
C58
C40
C64
C68
C36
C27
C73
C74
C86
C83
C56
C69
C15
C6
C16
C24
C57
C63
C67
C3
C71C72
C85
C81
C55
C103 C104 C105
C99
C107
C59
C91
C92
C78
C84
C80
C88
C62
C53
C79
C51
C66
C60
D18
D20
Q22
Q24
Q20
R17
0
R17
1
R17
2R16
1
R15
2R
150
R16
9
R12
4
R14
4
R156
R12
8
R130
U26
HSNK1
C1
C98
ZD1
R14
R132
RN2
Q25
C34
+-
+-
--
T0 SLAVE CPUCN1
LOOP 1 / 2 LED STATUS INDICATION/S
OUT
ON
ON
OK
SHORT CCT/ OPEN CCT
INDICATESIN
OFF
ON
OUT+
-
IN+
-LOOP 1IN
LOOP 1
Figure 19: Addressable Loop Termination Board
-
Page 23
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
4.14.1 Detector loop Isolator Installation In applications where it is not necessary to use an isolating base for each detector, up to 20 detectors may be installed between isolating bases.
Note: Refer to Apollo Isolating specifications and guidelines for further details. If a short circuit or abnormally low impedance occurs, the base isolates the negative supply in the direction of the fault. When the short circuit is removed the power will automatically be restored.
Note: Isolating base is polarity sensitive. 4.14.2 Loop Isolator calculator The number of isolating devices on the loop can limit the maximum loop cable length depending on the type of cable used and the total loop current. Refer to the tables below for reference.
Maximum Cable Length Using 1.5mm². Cable Number of Isolators 0 5 10 15 20 25 30 35 40 45 50 Loop Current Total (mA) MAX CABLE LENGTH USING 1.5mm².
50 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 100 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 150 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 200 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 960 250 1000 1000 1000 1000 973 933 893 853 813 733 733 300 971 931 891 851 811 771 731 691 651 611 571 350 850 810 770 730 690 650 610 570 530 490 450 400 756 716 676 636 596 556 516 476 436 396 356 450 680 640 600 560 520 480 440 400 360 320 280 500 618 578 538 498 458 418 378 338 298 258 218
Maximum Cable Length Using 2.5mm². Cable
Number of Isolators 0 5 10 15 20 25 30 35 40 45 50 Loop Current Total (mA) MAX CABLE LENGTH USING 2.5mm².
50 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 100 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 150 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 200 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 250 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 300 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 952 350 1000 1000 1000 1000 1000 1000 1000 950 883 817 750 400 1000 1000 1000 1000 993 926 859 793 726 659 593 450 1000 1000 1000 933 867 800 733 667 600 53 467 500 1000 964 897 930 764 697 630 564 497 430 364
4.14.3 Loop Open / Short Circuit. In the case of an Open Circuit or Short circuit (short circuit isolators used) on the Loop Line the Loop board provides the ability to drive out from both sides of the loop (In and Out). When these Faults are repaired / cleared the panel will still report a Loop Fault until a Loop Test is performed on the appropriate loop.
-
Page 24
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
5 FireFinder PLUS Control Panel
Figure 20: The FireFinder PLUS Control Panel
The LCD is used to display abnormal conditions and for interrogation, control and programming activities. When the FACP is in its normal state a default screen is displayed. In access level 2 or higher the backlight shall always be ON. Alarm, Fault and Disable information is accessed through the Main Menu.
Is the intended area for the Alarm Routing Address Code. This area is not printed on the Decal. 5.1 System Controls
- Active at access level 1, 2 and 3 This control is used to silence the local buzzer. Pressing this button will silence the panel buzzer, which sounds whenever there is a fire alarm or fault. The sound for a fire alarm is a steady sound where as for a fault it is intermittent.
- Active at access level 2 and 3. When the alarm devices are active (FACP is in the fire condition), activating the control will silence all alarms excluding the External Alarm device. Activating the control again, will resound the previously silenced alarm devices. If a new alarm is recognised whilst in the alarm devices are “silenced”, then all alarm devices shall sound. Note: If Delays to Outputs have been configured to investigate the delayed Alarm condition press the “Next” button and “Enter” button.
#1
#1
-
FIREFI
Previon th WhenFACP
This c This and wcontr
This c This Reso After requi Entiti
ThisThe
NDER PLUS
ous and Nexe current sel
n the “SEVEP. In order to
- Acontrol is use
control is uswon’t functionrol.
- control is use
control won’ound control.
disablemenred to remov
es which can
Zoneand
Sens Loop Soun
s control is ue indicator is
S (AUST)
xt controls arlected view.
ERAL ALARMo view the ala
Active at acced to reset th
sed to reset n unless the
Active at aced to disable
t function un
nt, output indve the panel
n be disabled
es – to provizone outputs
sors – loop b
p devices – w
nders – loop
used to disab
lit steady if a
INSTALLA
- Acre used to sc
MS” indicatoarms the PR
cess 2 and 3he FACP from
the FACP fralarm device
cess level 2e collective zo
nless the ala
dicators wonfrom the ala
d are:
de an options (sounders,
based
where the inp
based and m
- Active at able (and enabany zones or
Page 2
ATION,COMM
ctive at accescroll events o
r is illuminatEVIOUS and
m the fire co
rom the fire es have bee
ones and/or
rm devices h
n’t clear autorm condition
n to distinguibeacons, m
puts have be
monitored ou
ccess level 2ble) individuar devices hav
25
MISSIONING
ss level 1, 2 on the LCD. T
ted, then mud NEXT cont
ondition and t
condition anen silenced b
individual ad
have been s
omatically a.
sh between onitored out
een configure
utputs
2 and 3 al Zones andve been disa
G OPERATIO
and 3 The events b
ultiple fire alatrols are used
to clear the s
nd to clear thy means of A
ddressable p
ilenced by m
nd a subseq
zone inputs puts
ed as alarm i
d/or Devices.abled.
ON
being display
arms are pred.
system fault
he system faAlarm Silenc
points in alarm
means of Ala
quent reset
(sensors, d
nitiating
.
yed depends
esent on the
indicator.
ault indicatorce / Resound
m.
arm Silence /
operation is
etectors etc)
s
e
r d
/
s
)
-
Page 26
FIREFINDER PLUS (AUST) INSTALLATION,COMMISSIONING OPERATION
- Active at access level 2 and 3 This control is used to disable (and enable) the Alarm D