Download - Mig welding. Manufacturing Process
MANUFACTURING PROCESS
Name : Zia ur Rehman
Roll # 12-MC-16
Presented to : Sir Shah Nawaz
MIG Welding
Metal inert gas welding: a
method of welding in which the filler metal wire supplies the electric
current to maintain the arc, which is shielded from the access of air
by an inert gas, usually argon
The "Metal" in Gas Metal Arc
Welding refers to the wire that is used to start the arc. It is shielded by
inert gas and the feeding wire also acts as the filler rod. MIG is fairly
easy to learn and use as it is a semi-automatic welding process.
Metal Inert Gas (MIG) welding,
also sometimes called Gas Metal Arc Welding (GMAW) is a
process that was developed in the 1940s for welding aluminum and
other non-ferrous metals. MIG welding is an automatic or semi-
automatic process in which a wire connected to a source of direct
current acts as an electrode to join two pieces of metal as it is
continuously passed through a welding gun. A flow of an inert gas,
originally argon, is also passed through the welding gun at the
same time as the wire electrode. This inert gas acts as a shield,
keeping airborne contaminants away from the weld zone.
How The Machine Works
The Welder : Inside the welder you will find a spool of
wire and a series of rollers that pushes the wire out to the
welding gun.. If the wire feed jams up for any reason (this
does happen from time to time) you will want to check
this part of the machine out.The large spool of wire should
be held on with a tension nut. The nut should be tight
enough to keep the spool from unraveling, but not so tight
that the rollers can't pull the wire from the spool.
Assuming you are
using a shielding gas with your MIG welder
there will be a tank of gas behind the MIG.
The tank is either 100% Argon or a mixture
of CO2 and Argon. This gas shields the
weld as it forms. Without the gas your welds
will look brown, splattered and just
generally not very nice. Open the main
valve of the tank and make sure that there is
some gas in the tank.
The Gas Tank :
The Welding Gun
The welding gun is the
business end of things. It's where most of your
attention will be directed during the welding
process. The gun consists of a trigger that controls
the wire feed and the flow of electricity. The wire
is guided by a replaceable copper tip that is made
for each specific welder. Tips vary in size to fit
whatever diameter wire you happen to be welding
with.. The outside of the tip of gun is covered by a
ceramic or metal cup which protects the electrode
and directs the flow of gas out the tip of the gun.
During the MIG welding process, the
electrode melts within the arc and becomes deposited as filler material. The
shielding gas that is used prevents atmospheric contamination from atmospheric
and protects the weld during solidification. The shielding gas also assists with
stabilizing the arc which provides a smooth transfer of metal from the weld
wire to the molten weld pool.
Once your welder is set up and you have prepped your
piece of metal it's time to start focusing on the actual welding.If it's your first
time welding you might want to practice just running a bead before actually
welding two pieces of metal together. You can do this by taking a piece of scrap
metal and making a weld in a straight line of its surface.
Do this a couple of times before you start actually welding so that you can get a
feel for the process and figure out what wire speed and power settings you will
want to use.Every welder is different so you will have to figure these settings
out yourself. Too little power and you will have a splattered weld that won't
penetrate through your work piece. Too much power and you might melt right
through the metal entirely.
Once you've got your method tested
out a bit on some scrap, it's time to do the actual weld. In this photo I am doing
just a simple butt weld on some square stock. We've already ground down the
edges of the surfaces that are going to be welded so that the seem where they
meet makes a small "v". We are basically just taking the welder and making our
sewing motion across the top of the seem. It's ideal to weld from the bottom of
the stock up to the top, pushing the weld forward with the tip of the gun
If the weld is showing or you are
welding something that you want to look nice then you will most likely want to
grind down your weld and smooth it out. Slap a grinding wheel onto an angle
grinder and get started grinding on the weld.
Be careful as you approach the surface of the
original stock. You don't want to grind through your nice new weld or gouge
out a piece of the metal. Move the angle grinder around like you would a sander
so as not to heat up, or grind away any one spot of the metal too much. If you
see the metal get a blue tinge to it you are either pushing too hard with the
grinder or not moving the grinding wheel around enough. This is can happen
especially easily while grinding thing sheets of metal.
The neater your weld was the less grinding you
will have to do, and after you have spent a whole day grinding, you will see
why it's worth it to keep your welds neat in the first place. If you use a ton of
wire and made a mess of things it's ok, it just means that you might be grinding
for a while. If you had a neat simple weld though, then it shouldn't take too
long to clean things up.