© 2013 CADFEM CIS, ANSYS, Inc.1
Modeling of underground horizontal composite tank
Yury NovozhilovHead of HPC [email protected]
© 2013 CADFEM CIS, ANSYS, Inc.2
Creation FE model of underground horizontal composite tank in ANSYS Design Modeler, Composite PrePost, Mechanical
Parameterization of composite fibers stacking angles, properties of materials, the number of layers.
Linear buckling analysis and static structural analysis taking into account large displacements.
Objectives
© 2013 CADFEM CIS, ANSYS, Inc.3
The properties of the soil
ρ = 1500 кг/м3 – soil density
g = 9,81 м/с2 – acceleration of gravity
h = [5,8 ; 7,6] м – depth is of the point from the mark-plan
ν = 0,3 – soil Poisson's ratio
С = 12 МН/м3 – elastic foundation stiffness for loose saturated sands
Tsinovitch N.A. (Цитович Н.А.) “Soil Mechanics”, 1983
© 2013 CADFEM CIS, ANSYS, Inc.4
Geometry and dimensions
* Some dimensions are given with shell thickness of 6 mm taking into account
© 2013 CADFEM CIS, ANSYS, Inc.5
Elastic foundation
Boundary conditions and loads
© 2013 CADFEM CIS, ANSYS, Inc.6
Vertical component of pressure Pv = ρgh, Pa
Horizontal component of pressure Ph = ρghν/(1-ν), Pa
Ivanova P.L. (Иванова П.Л.) «Ground and foundation of hydraulic structures»
Boundary conditions and loads
© 2013 CADFEM CIS, ANSYS, Inc.7
Horizontal component of pressure Ph = ρghν/(1-ν), Pa
Ivanova P.L. (Иванова П.Л.) «Ground and foundation of hydraulic structures»
Boundary conditions and loads
© 2013 CADFEM CIS, ANSYS, Inc.8
Horizontal component of pressure Ph = ρghν/(1-ν), Pa
Ivanova P.L. (Иванова П.Л.) «Ground and foundation of hydraulic structures»
Boundary conditions and loads
© 2013 CADFEM CIS, ANSYS, Inc.9
Thickness 6 - 10 mm
Winding angle 5 - 20°
4 - 6 monolayers of equal thickness
Main tube
© 2013 CADFEM CIS, ANSYS, Inc.10
Caps Thickness 6 mm
Manual layout
3 layers of equal thickness: woven fiberglass cloth / mat / woven fiberglass
© 2013 CADFEM CIS, ANSYS, Inc.11
PVC pipes and saddlePVC pipes
Thickness 4 mm
Isotropic elastic material
Saddle
Thickness 6 mm
Winding angle 15°
4 monolayers of equal thickness
© 2013 CADFEM CIS, ANSYS, Inc.12
Reinforcements Thickness 6 мм
Manual layout
4 monolayers of equal thickness
© 2013 CADFEM CIS, ANSYS, Inc.13
2nd order shell elements
95751 DOFs
31917 Nodes
31870 Elements
FE Mesh
© 2013 CADFEM CIS, ANSYS, Inc.14
Buckling cross section mode (z = 1.8 m)
Linear buckling with 4 layer main tube
Load multiplier = 0.49 – not acceptable
© 2013 CADFEM CIS, ANSYS, Inc.15
Buckling cross section mode (z = 1.8 m)
Linear buckling with 6 layer main tube
Load multiplier = 1.33 – acceptable
© 2013 CADFEM CIS, ANSYS, Inc.16
Total deformation, |U|, m
© 2013 CADFEM CIS, ANSYS, Inc.17
Normal stress in cylindrical CS, σy, Pa
© 2013 CADFEM CIS, ANSYS, Inc.18
Model with 4 layer main tube• Load multiplier after the linear buckling analysis = 0.49 – not acceptable
Model with 6 layer main tube• Load multiplier after the linear buckling analysis = 1.33 – acceptable • Maximum of Total deformation is 54 mm• Normal stress in cylindrical CS σy = [-150 MPa; 136 MPa]
Results overview
© 2013 CADFEM CIS, ANSYS, Inc.19
Thank you for attention!
Yury NovozhilovHead of HPC [email protected]