ADVERTISE | SUBSCRIBE
Optics,Coatings,Mechanics,Motor Stages
Home > Science and Research > PHOTOVOLTAICS: Photoluminescence imaging speeds solar cell inspection
PH O TO VO LTAICS: Photolum inescence im aging speedssolar cell inspection12/01/2010
THORSTEN TRUPKE and WAYNE MCMILLAN
Laser-based photoluminescence imaging is a technique for rapid characterization of silicon samples by revealing a host of material and device properties. With acquisition times of typically a few seconds or even fractions of a second, megapixel luminescence images can be captured of silicon bricks, unprocessed and partially processed wafers, and fully processed cells. The quantitative luminescence imaging applications that have been developed over the last few years open up intriguing possibilities for inline process monitoring during silicon solar cell production.
Photovoltaics (PV) technology has grown into a substantial industry with annual revenues in 2009 estimated to be more than $40 billion, and it is expected to continue growing exponentially over years to come. The majority of PV manufacturing capacity is in wafer-based crystalline silicon solar cells; in 2008 the PV industry consumed 68% of silicon feedstock and has thus become the main consumer of silicon. So-called grid parity (the point at which an alternative means of generating electricity is equal in cost, or cheaper than grid power) is within reach in many countries but requires further improvements in manufacturing efficiency and yield to achieve necessary cost reduction.
Achieving high production yield at lower cost requires advanced process monitoring tools that allow inspection with high lateral spatial resolution of specific electronic and device parameters at various parts of the PV value chain at line speed on every sample. Sample throughput in PV manufacturing is up to 3600 wafers per hour. Existing measurement techniques, which in many cases were developed for much smaller sample throughput in microelectronics applications, are unable to fulfill such requirements—they are either too slow or cannot provide sufficient spatial information or both.
FIGURE 1. In a photoluminescence imaging setup, the output from a high-power fiber-coupled infrared (IR) laser is expanded to homogeneously illuminate a silicon brick, wafer, or solar cell. While the sample is illuminated (red arrows), a sensitive IR camera takes a snapshot of the luminescence signal (blue arrows) emitted by the sample.
Photoluminescence (PL) imaging of silicon bricks, wafers, and solar cells has been developed over recent years. Compared to measurement techniques such as microwave photoconductance decay (μ-PCD) mapping, PL imaging offers vastly superior speed and spatial resolution, making it perfectly suited for process monitoring in production. Developed by researchers at the University of New South Wales (UNSW) in Sydney, the patented technology enables PL images to be
measured with acquisition times less than 1 s.1 Only a few years after its introduction, research institutes and silicon wafer and solar cell manufacturers worldwide use commercial PL imaging equipment, which is offered by BT Imaging, a UNSW
spin-off company.2
How it works
In PL imaging of silicon samples, the entire surface of the sample—typically 156 × 156 mm—is illuminated homogeneously. The external optical excitation stimulates luminescence emission from the sample, which is captured with an infrared (IR) camera. In other words, a photograph is taken of the luminescent sample (see Fig. 1). With both excitation and detection being optical signals, PL imaging is contactless and can be applied to a wide range of samples, including silicon bricks and wafers. The measured luminescence comes from spontaneous emission within the sample; hence, the PL intensity allows assessment of the bulk electronic quality inside the sample. So photoluminescence imaging can be likened to x-ray imaging of wafers and cells.
FIGURE 2.Bulk minority carrier lifetime in microseconds can be obtained from
iPhone iPad Android
Sponsor Information
LASER FO CU S W O RLD M AGAZIN E
Read the Current Issue
Read Past Issues
Subscribe to Laser Focus World Magazine
Subscribe to Laser Focus World Newsletters
BU YERS GU IDE
• Laser Sources• Laser Specification Tables• Applied Optical Systems• Optical Coating & Fabrication• Optical Test & Measurement Equipment• Fiber-optic Components• Laser Systems Parts & Accessories• Detectors & Accessories• Materials & Substrates• Products & Services
Click here to have your products listed in the Laser Focus World Buyers Guide.
TO PIC IN D EX
View Laser Focus World articles by topic, A-Z
VID EO LIBRARY
View the Laser Focus World video library
ARTICLE ARCH IVE
View Laser Focus World past articles now.
TO PIC CEN TERS
Spectroscopy - NEW TOPIC
Detectors and Imaging
Fiber Optic Components & Systems
Lasers & Sources
Optical Components & Systems
Positioning, Support & Accessories
Photonics Education
Photonics Business
Science and Research
Software
Test & Measurement
H O M E BRO W SE BY TO PIC BU YERS GU IDE PRO DU CTS BU SIN ESS CEN TER EDU CATIO N RESO U RCES VID EO M O BILE JO BS
0
0
0
Share
0
Página 1 de 7PHOTOVOLTAICS: Photoluminescence imaging speeds solar cell inspection - Las...
01/03/2013http://www.laserfocusworld.com/articles/print/volume-46/issue-12/features/photovolt...
a PL image on a silicon brick. Variations in bulk lifetime due to crystal defects (dark line-shaped features) and due to contaminated regions (dark bands at the bottom and the top) are assessed in a matter of 30 s, where previously several hours were required.
Experimental challenges in PL imaging applications are: a) the required continuous optical power of typically 100 mW/cm2
over an area of at least 156 × 156 mm; b) the need for homogeneous illumination over that area; and c) the low luminescence quantum efficiency from silicon. For example, on some of the measurements on as-cut wafers discussed
further on, the number of luminescence photons emitted by the sample per incident photon is as low as 10-8.
High-power near-IR fiber-coupled laser diodes are often used as light sources in PL imaging. They provide the required high total optical continuous-wave power of more than 50 W, are sufficiently monochromatic and can easily be collimated to allow separation by optical filtering of the weak luminescence signal from the orders-of-magnitude stronger reflected excitation signal, and they can be turned into uniform illumination sources over large areas using customized beam-shaping optics. Furthermore, they are cost-effective, which is particularly relevant for inline PL imaging in PV production.
Applications
The production of a standard industrial solar cell includes the casting of feedstock into silicon ingots, cutting of ingots into bricks and wafers, and finally the processing of wafers into solar cells. The key quality parameter of the finished solar cell is its solar energy conversion efficiency. The latter depends strongly on the electronic material quality, which is given by the so-called excess minority carrier lifetime, and by device parameters such as the series resistance. Special PL imaging applications to assess these parameters have been developed with applicability across the entire PV value chain. Often these applications involve measuring and analyzing two or more images taken under different excitation and/or detection conditions.
0
0
0
Share
0
Página 2 de 7PHOTOVOLTAICS: Photoluminescence imaging speeds solar cell inspection - Las...
01/03/2013http://www.laserfocusworld.com/articles/print/volume-46/issue-12/features/photovolt...
FIGURE 4. Analyzing PL images taken under different illumination and bias conditions shows series resistance (Ω/cm2) information. The pattern of features with enhanced series resistance is caused by the metal belt in the firing furnace.
Bulk lifetime measurements on silicon bricks: Application of PL imaging to silicon bricks prior to wafer cutting allows assessment of the electronic material quality at an early production stage. A PL image taken on the side facet of a 24 × 15.6 cm silicon brick can be calibrated into a color scale that represents the bulk minority carrier lifetime in microseconds
(see Fig. 2).3 Measurement time for this image was 30 s. The same measurement with equivalent spatial resolution using conventional μ-PCD mapping would take several hours. A further advantage of PL imaging is that it allows measurement of the so-called "bulk minority carrier lifetime," a more relevant physical quantity in practice than the "effective minority carrier lifetime," which is measured by μ-PCD mapping. The bulk lifetime information from PL can predict wafer quality and provide feedback on feedstock quality as well as offering a fast process monitoring tool that allows process optimization and process excursions to be detected early. An example of process excursions in production is the formation of slip lines in monocrystalline silicon ingots, which can be reliably detected by PL imaging on silicon ingots and slabs without the need
for any surface preparation.4
As-cut wafer characterization: Wafer manufacturing and cell manufacturing are separate parts of the PV value chain, generally performed in different factories by different companies. Photoluminescence imaging can be used for both outgoing quality control (wafer makers) and incoming quality control (cell makers). An as-cut multicrystalline silicon wafer can be imaged without any surface preparation (see Fig. 3). The BT Imaging iLS-W1 used for that measurement is an automated inline PL imaging system with a throughput of up to 2400 wafers per hour, capable for the first time of measuring as-cut wafer PL images with less than 1 s exposure time. The red color overlay marks the position of specific types of defects related to structural defects within the silicon crystal lattice—defects that have a dominant impact on cell efficiency. The position of those defects was obtained from the PL image by image-processing algorithms trained to identify specific spatial features. Systematic PL imaging inspection of silicon wafers and automatic assessment of metrics derived using image-analysis methods allow cell performance to be predicted at the start of cell manufacturing—a unique
opportunity enabled for the first time by fast PL imaging.5,6,7 Analyzing PL on silicon wafers from bottom to top of a silicon brick also enables the 3D distribution of defects within a brick to be measured, valuable information for gaining understanding and better control of the crystallization process.
Series resistance imaging: A strong correlation exists between the local PL signal and the local voltage within a solar
cell. This allows quantitative assessment of the local series resistance in a fully processed solar cell.8 Photoluminescence-based series resistance imaging is based on measuring a number of PL images with different combinations of illumination intensity and bias conditions. It provides the local series resistance with high resolution in a matter of seconds. Previously the only widely used technique to measure such variations in solar cells was with a product called Corescan, a
measurement technique that typically requires 40 min per cell and destroys the sample in the process.9 An example of a series resistance image from PL imaging shows series resistance patterns that match the shape of the belt in the firing furnace, providing immediate clues on the origin of the problem (see Fig. 4). With measurement times on the order of seconds, inline Rs imaging is conceivable, allowing small process excursions to be identified and rectified earlier than previously possible.
0
0
0
Share
0
Página 3 de 7PHOTOVOLTAICS: Photoluminescence imaging speeds solar cell inspection - Las...
01/03/2013http://www.laserfocusworld.com/articles/print/volume-46/issue-12/features/photovolt...
Print Email Save
RSS
Font Sizes:
Facebook Twitter LinkedIn
0
Share
FIGURE 3. In a photoluminescence image of a 156 × 156 mm as-cut multicrystalline silicon wafer, a red color overlay displays the result of automatic image-processing analysis for a specific defect type. Metrics derived from such image analysis allow correlation with and prediction of cell performance based on measurements on the starting material. The image was taken using a BT Imaging iLS-W1 inline inspection system.
Photoluminescence imaging of silicon bricks, wafers, and solar cells has seen rapid development since its introduction in 2005. The application of PL imaging is not limited to the specific applications mentioned here. A large number of additional applications have now been demonstrated and that number is growing even more rapidly with the availability and penetration of commercial PL imaging systems offered by BT Imaging. The company recently launched specialized equipment for inline quality control and process monitoring. With its combination of speed and high spatial resolution, PL imaging is on the verge of being adopted for inline monitoring in PV manufacturing. It can also be expected to find applications in other arenas, such as the semiconductor and LED industries.
REFERENCES1. T. Trupke et al., "Photoluminescence imaging of silicon wafers," Appl. Phys. Lett., 89, p. 044107 (2006).2. www.btimaging.com3. T. Trupke et al., "Photoluminescence imaging on silicon bricks," 24th European Photovoltaic Solar Energy Conf., Hamburg, Germany (September 2009).4. W. McMillan et al., "Slip line detection on mono ingots and wafers at production throughput using photoluminescence," 25th EPVSC, Valencia, Spain (September 2010).5. M. Demant et al., "Analysis of luminescence images applying pattern recognition techniques," 25th EPVSC, Valencia, Spain (September 2010).6. J. Haunschild et al., "Comparing luminescence imaging with illuminated lock-in thermography and carrier density imaging for inline inspection of silicon solar cells," 24th European Photovoltaic Solar Energy Conf., Hamburg, Germany (September 2009).7. W. McMillan et al., "In-line monitoring of electrical wafer quality using photoluminescence imaging," 25th EPVSC, Valencia, Spain (September 2010).8. T. Trupke et al., "Spatially resolved series resistance of silicon solar cells obtained from luminescence imaging," Appl. Phys. Lett., 90, p. 093506 (2007).9. A.S.H.v.d. Heide et al., "Mapping of Contact Resistance and Locating Shunts on Solar Cells Using Resistance Analysis by Mapping of Potential (Ramp) Techniques," 16th EPVSC, Glasgow, UK (2000).
Editor's note: Find out more about the market for photovoltaic equipment and market outlook at the 2011 Lasers & Photonics Marketplace Seminar in January. For information or to register, visit www.marketplaceseminar.com.
Thorsten Trupke is a founder and CTO, and Wayne McMillan is VP, sales & marketing, at BT Imaging Pty Ltd., 2-12 Foveaux Street, Surry Hills, NSW, 2010, Australia; e-mail: [email protected]; www.btimaging.com.
Tell us what you think about this article. Send an e-mail to [email protected].
More Laser Focus World Current Issue ArticlesMore Laser Focus World Archives Issue Articles
0
0
0
Share
0
0 0 0 0
Página 4 de 7PHOTOVOLTAICS: Photoluminescence imaging speeds solar cell inspection - Las...
01/03/2013http://www.laserfocusworld.com/articles/print/volume-46/issue-12/features/photovolt...
0 Comments RSS | Subscribe
Silica nanowires from University of Southampton are 15 times stronger than steel
Open Photonics facilitates R&D-to-commercialization process
Laser Marketplace Seminar a month away--register now!
Laser Market Review & Forecast from Strategies Unlimited available for pre-release ordering
The dangers of photonicsMon Jan 28 18:35:00 CST 2013 - Photon Focus
A new tool for prototyping flexible photonicsFri Jan 25 10:16:00 CST 2013 - Photon Focus
Broader view for adaptive opticsMon Jan 21 14:42:00 CST 2013 - Spectral Bytes
2013: Laser markets, trends, analysisThu Jan 17 10:14:00 CST 2013 - Photon Focus
In-air touch-enabled displayThu Jan 10 16:31:00 CST 2013 - Photon Focus
Zero refractive indexTue Jan 08 14:27:00 CST 2013 - Spectral Bytes
Would you "iRobot" with Jules?Mon Jan 07 11:03:00 CST 2013 - Photon Focus
Marketing people LOVE -- reallyWed Jan 02 15:57:00 CST 2013 - Marketing for Engineers
Top photonics articles in 2012 point to 2013Wed Jan 02 08:10:00 CST 2013 - Photon Focus
How laser 'printing' builds DNAThu Dec 20 15:17:00 CST 2012 - Spectral Bytes
ED ITO RS' PICKS
RECEN T BLO GS
View More Blogs
M O ST PO PU LAR ARTICLES
PHOTONICS APPLIED: LIDAR: Wind energy gets a boost from wind-turbine lidar
MEDICAL APPLICATIONS OF FIBER-OPTICS: Optical fiber sees growth as medical sensors
Downhole fiber-optic sensing focus of Halliburton's Pinnacle Applied Photonics Center
Graphene multiplies the power of light
AMS Technologies names Klaus Maier as regional sales director
Magnify your intellectual property IQ at SPIE Photonics West 2013
General Atomics to build a second 150 kW HELLADS military laser, this one for the U.S. Navy
Smart controller from Energetiq available for company's laser-driven light sources
3D solar cells generate up to 20 times more energy
05/11/2012
Northrop Grumman demonstrates anti-cruise missile laser weapon
05/06/2012
Quantum-dot VCSELs can emit anywhere in the visible spectrum
04/30/2012
Terahertz microchip could let cell phones see through walls
04/27/2012
Laser-based 3D nozzle quality test from Fraunhofer ILT improves laser material deposition
04/26/2012
FIBER LASERS: Fiber lasers: The state of the art
04/01/2012
DIODE-PUMPED SOLID-STATE LASERS: Laser dazzlers are deployed
03/01/2012
OPTICAL DATA STORAGE: Holographic data storage uses volumetric crystal media
02/07/2012
RECEN T ARTICLES
FRO M TH E ARCH IVES
More Laser Focus World Current Issue ArticlesMore Laser Focus World Archives Issue Articles
PO ST A CO M M EN T
Easily post a comment below using your Linkedin, Twitter, Google or Facebook account.
Post a new comment
0
0
0
Share
0
Login
Post
Página 5 de 7PHOTOVOLTAICS: Photoluminescence imaging speeds solar cell inspection - Las...
01/03/2013http://www.laserfocusworld.com/articles/print/volume-46/issue-12/features/photovolt...
Magnify your intellectual property IQ at SPIE Photonics West 2013
Superconducting nanowire single-photon detector has near-unity detection efficiency
Silica nanowires from University of Southampton are 15 times stronger than steel
Bodkin lands Air Force hyperspectral imaging contract
Leica Microsystems research microscopy software optimized for fluorescence imaging
Magnify your intellectual property IQ at SPIE Photonics West 2013
General Atomics to build a second 150 kW HELLADS military laser, this one for the U.S. Navy
Epigem secures nearly $600K to commercialize flexible OLEDs for EU Flex-o-Fab project
Laser modules from ProPhotonix have output powers up to 150 mW
Virtual reality glasses from Google's Project Glass could have projected keyboard
Magnify your intellectual property IQ at SPIE Photonics West 2013
Epigem secures nearly $600K to commercialize flexible OLEDs for EU Flex-o-Fab project
Silica nanowires from University of Southampton are 15 times stronger than steel
Virtual reality glasses from Google's Project Glass could have projected keyboard
NASA demonstrates laser communication between Earth and Lunar orbiter
Leica Microsystems research microscopy software optimized for fluorescence imaging
Open Photonics facilitates R&D-to-commercialization process
Spectroscopy software from Avantes features multimonitor setups
3D holograms assist battle preparation
DESIGN FOR MANUFACTURING: Practical design software eases asphere manufacturability
Beam profiler from Ophir Photonics Group measures at rates over 20 Hz
Mitutoyo measuring microscopes feature LED illumination
Raman microspectrometer from CRAIC Technologies integrates with optical microscopes
FIBER-OPTIC SENSING: Distributed fiber-optic sensing solves real-world problems
DETECTO RS AN D IM AGIN G
More Detectors and Imaging
LASER & SO U RCES
More Laser & Sources
O PTICAL CO M PO N EN TS & SYSTEM S
More Optical Components & Systems
SO FTW ARE
More Software
TEST & M EASU REM EN T
Sandia’s laser-guided bullet prototype can hit small targets a mile away
02/02/2012
Huawei and Vodafone complete first 2 Tbit/s WDM field trial
3SAE Technologies optical fiber tester performs destructive testing up to 50 N
Silica nanowires from University of Southampton are 15 times stronger than steel
UC Irvine neuroscientists terminate epileptic seizures with implanted optical fibers
FIBER-OPTIC SENSING: Distributed fiber-optic sensing solves real-world problems
Huawei and Vodafone complete first 2 Tbit/s WDM field trial
3SAE Technologies optical fiber tester performs destructive testing up to 50 N
Silica nanowires from University of Southampton are 15 times stronger than steel
UC Irvine neuroscientists terminate epileptic seizures with implanted optical fibers
FIBER-OPTIC SENSING: Distributed fiber-optic sensing solves real-world problems
General Atomics to build a second 150 kW HELLADS military laser, this one for the U.S. Navy
Superconducting nanowire single-photon detector has near-unity detection efficiency
Virtual reality glasses from Google's Project Glass could have projected keyboard
White LED has gallium oxide substrate, vertically placed electrodes
NASA demonstrates laser communication between Earth and Lunar orbiter
Raman microspectrometer from CRAIC Technologies integrates with optical microscopes
Bodkin lands Air Force hyperspectral imaging contract
High-performance spectral systems goal of Avantes and Tornado partnership
Semrock puts 11-band optical filter into production
Raman analyzer from BaySpec is customizable to any wavelength range
FIBER O PTIC CO M PO N EN TS &SYSTEM S
More Fiber Optic Components & Systems
PO SITIO N IN G, SU PPO RT &ACCESSO RIES
More Positioning, Support & Accessories
SCIEN CE AN D RESEARCH
More Science and Research
SPECTRO SCO PY
More Spectroscopy
0
0
0
Share
0
Página 6 de 7PHOTOVOLTAICS: Photoluminescence imaging speeds solar cell inspection - Las...
01/03/2013http://www.laserfocusworld.com/articles/print/volume-46/issue-12/features/photovolt...
InView Technology compressive sensing workstation includes objective lens
High-performance spectral systems goal of Avantes and Tornado partnership
More Test & Measurement
© 2013. PennWell Corporation. All Rights Reserved. PRIVACY POLICY | TERMS AND CONDITIONS | SITE MAP
0
0
0
0
Share
0
TOPICS
Biophotonics
Detectors and Imaging
Fiber Optics Components & Systems
Lasers & Sources
Optical Components & Systems
Positioning, Support & Accessories
Science and Research
Software
Test & Measurement
ABOUT US & SUPPORT
Laser Focus World Magazine
Contact Us
About Us
Advertising
Subscribe
Login
Register
RSS
RESOURCES
Webcasts
White papers
Editorial Digests
Video
Blogs
Events
PennWell Events
PennWell Websites
Strategies Unlimited
SECTOR PUBLICATIONS
Laser Focus World
Laser Focus World Japan
Laser Focus World China
Industrial Laser Solutions
Industrial Laser Solutions China
Industrial Laser Solutions Japan
BioOptics World Magazine
STAY CONNECTED
Linked In
Página 7 de 7PHOTOVOLTAICS: Photoluminescence imaging speeds solar cell inspection - Las...
01/03/2013http://www.laserfocusworld.com/articles/print/volume-46/issue-12/features/photovolt...