1
4
5
7
9
11
13
15
17
19
21
23
UNIC is...
NEW Products
UNIC Truck Mounted Crane
UNIC Truck Crane Line Up
URW 230 Series
URW 260 Series
URW 290 Series
URW 340 Series
URW 370 Series
URW 500 Series
URW 540 Series
URU 800 Series
CONTENTS
1
VER
SA
TILE
STR
ON
G
Operational advantages…
Heavy Lifts with a winch rope crane…
The working radius can increase when the load is lifted with a knuckle boom crane.
An 8TM UNIC easily lifts a 3 tonne cable drum. This is not possible with even a 9TM knuckle boom crane.
The Lift Curve Graph of a typical 9TM knuckle boom crane shows it cannot lift a 3 tonne load onto the tray.
When a load is raised by a winch rope crane, the working radius does not increase.
Buildings, walls, whatever, with UNIC wire-rope cranes you get precise high-lift placement and safe, sure operation. Their dependability is all in their strength and design, original UNIC features.
Higher performance, too, at lower depths. UNIC wire-rope cranes handle heavy loads in deep-hole jobs with accuracy and stability. A wide range of models assures versatile matching to job requirements.
Tight places are the right places for UNIC wire-rope cranes. In any operating situation their strong steel cables mean extra dependability and safety. High, low or tight, UNIC wire-rope cranes are always right.
UNIC IS...
2
SM
AR
TSIM
PLE
PR
OB
LEM
SO
LVIN
G
Automatic Hook Stow System…
Hook storage on a knuckle boom crane fi tted with a winch is always a problem.Not with a UNIC. Flick one switch - job done!
Control lever layout…
Synchronised control levers are laid out for operational ease. One hand can boom telescope and simultaneously hook down or reverse. UNIC control levers also have refl ective direction symbols for safer operation in low light situations.
Digital Load Meter...
The digital load meter provides clear critical load weight information to the operator at all times.
3
UNIC IS...EFFIC
IEN
T
Automative Throttle Advance…
This is an inbuilt feature of UNIC cranes. Incorporated into the control levers, increase truck engine revs proportionally with lever movement. This provides optimums in control of load handling, speed of hook travel, fuel economy and noise control.
Anti-two block system…
UNIC’s anti two-block system means that there is no fear of the hook striking the boom tip.The overwind alarm and auto stop is a standard in all UNIC truck cranes.
Without this feature the dangerous practice of overwinding can easily occur.
Three Light Tower…
Optional on all new UNIC cranes. This safety feature is clear, bright and visible to everyone on site.
SA
FE
VIS
IBLE
NBRequires to interface with the chassis manufacturerssuitable “throttle pod” system.
4
NEW PRODUCTS
Read…
• Exactly what you can lift in kg• Exactly what you are lifting in kg• Critical information such as boom
length, angle and radius
Observe…
• The load factor bar• Signal strength
Control…
• Crane operating speed• All crane functions• Warning horn and much more
UNIC’s Super Stability System automatically…
• Detects outrigger extension from nil to half to full extension.• Detects outrigger ground contact• Works three separate zones - left, right and overfront• Automatically adjusts the Moment Limiter to match the
stabiliser setting• Automatically changes Moment Limiter as the boom slews
from zone to zone.
AS YOU WORK
SUPER ML RADIO REMOTE TRANSMITTER
Australia’s NEW Super ML Radio Remote Transmitter gives the operator remote access to load weight and crane capacity information.Additional features include a warning lamp and load factor bar.
SUPER STABILITY SYSTEM
Need to work next to heavy traffi c?
Need to work overfront of truck?
Need to work in confi ned areas?
Just want to load or unload a light item quickly?
Need to do all of that with the best safety and control?
THEN CHOOSE UNIC
5
The UNIC truck mounted crane incorporates superior lifting performance, a wide working range, ease of operation and second-to-none safety features to provide multipurpose hydraulic cranes that are engineered to handle a great variety of loading operations. In addition to normal lifting operations, UNIC truck mounted cranes excel in work involving the lowering of cargo below ground level via the use of a winch. It offers excellent operational control and accurate load placement.
UNIC Truck mounted cranes provide an endless variety of applications and support for many industries including:Transportation, Construction, Landscaping, Lumber, Railroad Work, Iron & Steel Production, Recycling & Salvage, Steel Erection, Poles & Signwork, Marine, Irrigation, and Drilling.
perations. In s, UNIC truckving the
vel via the perationalent.
e an endless t for many
caping, Production, , Poles & lling.
HIGH LEVEL PERFORMANCE
With its hoist-winch and long straight telescopic boom, the UNIC provides exceptionally high level lifting performance.
UNIC TRUCK M
6
MAXIMUM CONTROL & PRECISION
Controlling the speed from high to low means maximum control in even the most challenging situations.
OPERATION RANGE
A wide working range means that UNIC can handle cargo in high places, below ground or placed at a distance from the truck.
OUNTED CRANE
7
URW230 seriesLifting capacity 2,330 kg
Max hook height 9.8 m
Number of booms 4
Recommended min. chassis GVM 7,500 kg
URW290 seriesLifting capacity 3,030 kg
Max hook height 13.9 m
Number of booms 6
Recommended min. chassis GVM 10,400 kg
URW340 seriesLifting capacity 3,030 kg
Max hook height 11.7 m
Number of booms 4
Recommended min. chassis GVM 12,000 kg
URW260 seriesLifting capacity 2,630 kg
Max hook height 13.9 m
Number of booms 6
Recommended min. chassis GVM 7,500 kg
UNIC TRUCK
8
URW370 seriesLifting capacity 3,030 kg
Max hook height 16.2 m
Number of booms 6
Recommended min. chassis GVM 12,000 kg
URW540 seriesLifting capacity 4,050 kg
Max hook height 19.8 m
Number of booms 6
Recommended min. chassis GVM 15,000 kg
URU800 seriesLifting capacity 8,200 kg
Max hook height 17.5 m
Number of booms 5
Recommended min. chassis GVM 24,000 kg
URW500 seriesLifting capacity 3,030 kg
Max hook height 17.6 m
Number of booms 6
Recommended min. chassis GVM 15,000 kg
CRANE LINE UP
9
URW230 series
SPECIFICATIONS
CRANE MODEL URW232 URW233 URW234Max lifting capacity Max 2330kg at 1.7m
Working radius Min 0.59m, Max 4.23m Min 0.6m, Max 6.23m Min 0.68, Max 8.43m
Max hook height (approx.)
Above ground 5.6m 7.6m 9.7m
Below ground 4.8m with 4-part line 7.2m with 4-part line 9.9m with 4-part line
Boom length Min 2.5m, Max 4.4m Min 2.59m, Max 6.4m Min 2.87m, Max 8.6m
Boom sections 2-section box beam type telescoping boom
3-section box beam type telescoping boom
4-section box beam type telescoping boom
Boom raise angle 1° to 76°
Slewing angle 360° continuous
WinchSingle line pull 5.64kN {575kgf}
Wire rope Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length: 8mm x 34m / Breaking strength: 42.4kN {4320kgf}
Outriggers
Vertical jacks, double acting hydraulic cylinders with pilot-operated check valves / Horizontal beams, manual extension type
Retracted: 1.546m, Extended: 2.6m, Mid-extended: 2.1m
Hydraulic pump Rated pressure 20.6MPa {210kgf/cm2)
Hydraulic oil tank capacity 22L
Safety devices
Pressure relief valve for hydraulic circuit / Counterbalance valves for boom raising and boom telescoping cylinders / Pilot-operated check valves for vertical outrigger cylinders / Boom angle indicator with load indicator / Hook safety latch / Automatic mechanical brake for winch / Digital load meter / Automatic stop for overwinding / Overwinding alarm / Alarm
buzzer / Level / Emergency stop button / Overloading alarm / Turnover protection
RADIOREMOTE
CONTROL
2,330 kg
APPROX. 9.8 mLIFTING CAPACITY
MAX. HOOK HEIGHTABOVE GROUND
10
315 203
389
1,574
175
STROKE379
TRUCK FRAME
176
250
187
179
564
179
176
24
ROTATION CENTER
1,856
692
115
115
STROKE437
MAX2,600
MID2,100
MIN1,726
STROKE437
CRANE MOUNTING DIMENSIONS
CRANE MODEL
UR-W234 3,065 Min. 2,870 ~ Mid. 4,800 ~ 6,700 ~ Max. 8,600 1,849 1,840
UR-W233 2,784 Min. 2,590 ~ Mid. 4,520 ~ Max. 6,400 1,826 1,816
UR-W232 2,694 Min. 2,500 ~ Max. 4,400 1,826 1,816
Drawing: UR-W234 (Unit: mm)
1
1
2
2
3
3
4
4
Maximum Working Radius 4.23m.
RATED LOAD
W2322 Sections Boom
Working Radius 0.59 ~ 1.72.33
4.234.03.53.02.52.22.00.981.08 0.931.281.531.832.03
0(m) 1 2 3 4
Working Radius
Heig
ht A
bove
Gro
und
(m)
(m)
4
5(5.7)
3
1 20 3 (4.23)(0.59)
2
70̊76̊
50̊40̊
30̊20̊10̊1˚
60̊
1
Maximum Working Radius 6.23m.
RATED LOAD
W2333 Sections Boom
Working Radius 0.60 ~ 1.72.33
6.235.04.03.53.02.52.22.00.88(4.35m)0.981.081.281.531.832.030.68 0.530.881.031.23
0(m) 1 2 3 4 5 6
Working Radius
Heig
ht A
bove
Gro
und
(m)
(m)
2 30 1 4 5 (6.23)(0.60)
4
5
6
7(7.7)
3
2
70̊76̊
60̊50̊
40̊
30̊
20̊
10̊
1˚
1
Maximum Working Radius 8.43m.
RATED LOAD
W2344 Sections Boom
Working Radius 0.68 ~ 1.72.33
8.438.07.06.05.04.03.53.02.52.22.00.83 (4.63m)0.981.081.281.531.832.030.68 0.53 (6.53m)0.580.881.031.23
0.36 0.310.430.53 92.086.0
0(m) 1 2 3 4 5 6 7 8
Working Radius
Heig
ht A
bove
Gro
und
76̊
(m)
(m)
2 30 1 4 5 6 7 (8.43)(0.68)
(9.8)
3
4
5
6
7
8
9
2
1
70̊60̊
50̊
40̊
30̊
20̊
10̊
1˚
11
URW260 series
SPECIFICATIONS
CRANE MODEL URW263 URW264 URW265 URW266Max lifting capacity 2630kg at 1.6m 2630kg at 1.6m 2630kg at 1.5m 2630kg at 1.5m
Max working radius 6.43m 8.43m 10.63m 12.63m
Max hook height (approx.)
Above ground 7.9m 9.8m 12m Max 13.9m
Below ground 7.4m with 4-part line 9.9m with 4-part line 12.5m with 4-part line
14.8m with 4-part line
Boom length Min 2.79m, Max 6.6m Min 2.87m, Max 8.6m Min 3.15m, Max 10.8m Min 3.25m, Max 12.8m
Boom sections 3-section box beam type telescoping boom
4-section box beam type telescoping boom
5-section box beam type telescoping boom
6-section box beam type telescoping boom
Boom raise angle 1° to 76°
Slewing angle 360° continuous
Winch
Single line pull 6.37kN {650kgf}
Wire rope
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 44m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 54m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 64m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 73.5m / Breaking strength: 42.4kN {4320kgf}
Outriggers
Vertical jacks, double acting hydraulic cylinders with pilot-operated check valves / Horizontal beams, manual extension type
Retracted: 1.726m, Extended: 3.0m, Mid-extended: 2.4m
Retracted: 1.71mExtended: 3.4mMid-extended:
2.4m, 2.9m
Hydraulic pump Rated pressure 20.6MPa {210kgf/cm2)
Hydraulic oil tank capacity 22L
Safety devices
Pressure relief valve for hydraulic circuit / Counterbalance valves for boom raising and boom telescoping cylinders / Pilot-operated check valves for vertical outrigger cylinders / Boom angle indicator with load indicator / Hook safety latch / Automatic mechanical brake for winch / Digital load meter / Automatic stop for overwinding / Overwinding alarm / Alarm
buzzer / Level / Emergency stop button / Overloading alarm / Turnover protection
2,630 kgAPPROX.13.9 mLIFTING CAPACITYMAX. HOOK HEIGHT
ABOVE GROUND
RADIOREMOTE
CONTROL
12
CRANE MOUNTING DIMENSIONSCRANE MODEL
UR-W266 3,439 Min. 3,250 ~ Mid. 5,180 ~ 7,100 ~ 9,000 ~ 10,900 ~ Max. 12,800 1,963 2,043
UR-W265 3,339 Min. 3,150 ~ Mid. 5,080 ~ 7,000 ~ 8,900 ~ Max. 10,800 1,917 1,910
UR-W264 3,059 Min. 2,870 ~ Mid. 4,800 ~ 6,700 ~ Max. 8,600 1,854 1,844
UR-W263 2,979 Min. 2,790 ~ Mid. 4,720 ~ Max. 6,600 1,839 1,829
12
3 4
1 2 3 4
Drawing: UR-W266(Unit: mm)
Working Radius 1.5 1.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.63
2.63 2.13 1.93 1.53 1.18 (3.08m)
2.63 2.13 1.93 1.53 1.23 1.03 0.93 0.83 0.73 (5.01m)
1.23 1.03 0.88 0.73 0.63 0.58 0.53 0.43 (6.93m)
0.68 0.60 0.53 0.48 0.43 0.36 0.31 0.29 (8.83m)
0.38 0.33 0.29 0.26 0.22 0.19 0.16 0.14 0.14 (10.73m)
0.22 0.18 0.15 0.13 0.12 0.11 0.10 0.10
Working Radius 1.5 1.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 7.0 8.0 9.0 10.0 10.63
2.63 2.13 1.93 1.53 1.28 (2.98m)
2.63 2.13 1.93 1.53 1.28 1.08 0.98 0.78 (4.91m)
1.23 1.03 0.88 0.78 0.68 0.63 0.58 0.50 (6.83m)
0.68 0.60 0.53 0.48 0.43 0.36 0.31 0.29 (8.73m)
0.38 0.33 0.29 0.26 0.22 0.19 0.16 0.14 0.14
Working Radius 1.6 1.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.43
2.63 2.23 2.03 1.53 1.43 (2.62m)
2.63 2.23 2.03 1.53 1.28 1.08 0.98 0.88 (4.55m)
1.23 1.23 1.03 0.88 0.78 0.68 0.63 0.53
Working Radius 1.6 1.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 7.0 8.0 8.43
2.63 2.23 2.03 1.53 1.43 (2.70m)
2.63 2.23 2.03 1.53 1.28 1.08 0.98 0.83 (4.63m)
1.23 1.03 0.88 0.78 0.68 0.63 0.58 0.53 (6.53m)
0.68 0.58 0.53 0.48 0.43 0.36 0.31 0.29
Maximum Working Radius 12.63m.
W2666 Sections Boom
0(m)1 23 4567 89 10 11 12
RATED LOAD
Maximum Working Radius 10.63m. W265
5 Sections Boom
0(m)1 23 456 78 91 0
RATED LOAD
Maximum Working Radius 8.43m. W2644 Sections Boom
0(m)1 23 456 78
RATED LOAD
Maximum Working Radius 6.43m. W2633 Sections Boom
0(m)1 23 45 6
RATED LOAD
13
URW290 series
3,030 kgLIFTING CAPACITY
SPECIFICATIONS
CRANE MODEL URW293 URW294 URW295 URW296Max lifting capacity 3030kg at 1.6m 3030kg at 1.6m 3030kg at 1.5m 3030kg at 1.5m
Max working radius 6.43m 8.73m 10.63m 12.63m
Max hook height (approx.)
Above ground 7.9m 10.1m 12.0m 13.9m
Below ground 7.4m with 4-part line 10.1m with 4-part line 12.5m with 4-part line 14.9m with 4-part line
Boom length Min 2.79m, Max 6.6m Min 3.17m, Max 8.9m Min 3.15m, Max 10.8m Min 3.25m, Max 12.8m
Boom sections 3-section box beam type telescoping boom
4-section box beam type telescoping boom
5-section box beam type telescoping boom
6-section box beam type telescoping boom
Boom raise angle 1° to 76°
Slewing angle 360° continuous
Winch
Single line pull 7.35kN {750kgf}
Wire rope
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 44m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 55m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 64m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 73.5m / Breaking strength: 42.4kN {4320kgf}
Outriggers
Vertical jacks, double acting hydraulic cylinders with pilot-operated check valves / Horizontal beams, manual extension type
Retracted: 1.71m, Extended: 3.4m, Mid-extended: 2.4m, 2.9m
Hydraulic pump Rated pressure 20.6MPa {210kgf/cm2)
Hydraulic oil tank capacity 22L
Safety devices
Pressure relief valve for hydraulic circuit / Counterbalance valves for boom raising and boom telescoping cylinders / Pilot-operated check valves for vertical outrigger cylinders / Boom angle indicator with load indicator / Hook safety latch / Automatic mechanical brake for winch / Digital load meter / Automatic stop for overwinding / Overwinding alarm / Alarm
buzzer / Level / Emergency stop button / Overloading alarm / Turnover protection
APPROX.13.9 mMAX. HOOK HEIGHT
ABOVE GROUND
RADIOREMOTE
CONTROL
14
195
250
250
345
195
24
ROTATION CENTER
STROKE845
STROKE845
MAX3,400MID(2)2,900MID(1)2,400
MIN1,710
179
179
564
115
115
692
1,860
175
1,579
325768
389
STROKE379
222
TRUCK FRAME
CRANE MOUNTING DIMENSIONSCRANE MODEL
UR-W296 3,439 Min. 3,250 ~ Mid. 5,180 ~ 7,100 ~ 9,000 ~ 10,900 ~ Max. 12,800 1,963 2,043
UR-W295 3,339 Min. 3,150 ~ Mid. 5,080 ~ 7,000 ~ 8,900 ~ Max. 10,800 1,917 1,910
UR-W294 3,359 Min. 3,170 ~ Mid. 5,100 ~ 7,000 ~ Max. 8,900 1,856 1,849
UR-W293 2,979 Min. 2,790 ~ Mid. 4,720 ~ Max. 6,600 1,859 1,851
Drawing: UR-W294 (Unit: mm)
12
3 4
1 2 3 4
Maximum Working Radius 12.63m.
W2966 Sections Boom
0(m) 1 2 3 4 5 6 7 8 9 10 11 12
Working Radius 12.630.78 ~1.53.03
0.10
12.0
0.13
11.0
0.13
10.0
0.14
9.0
0.16
8.0
0.18
7.0
0.21
6.0
0.24
5.04.03.53.02.52.01.80.80 (5.01m)1.031.231.431.732.132.430.73 0.50 (6.93m)0.600.931.081.281.53
0.41 0.33 (8.83m)0.360.480.580.730.830.930.20 0.18 (10.73m)0.180.230.260.300.380.48
1.73 (2.20m)
0.28 (5.30m)
Working Radius
Heig
ht A
bove
Gro
und
76̊
20 1 3 4 5 6 7 8 9 10 11(12.63)(0.78)
(13.9)
345678910111213
21
(m)
(m)
70̊60̊
40̊
30̊
20̊
10̊
1˚
50̊
RATED LOAD
Working Radius
Heig
ht A
bove
Gro
und
76̊
(12.0)
34567891011
320 1 4 5 6 7 8 9 (10.63)(0.75)
12
(m)
(m)
70̊60̊
40̊
30̊
20̊
10̊
1˚
50̊Maximum Working Radius 10.63m. W295
5 Sections Boom
Working Radius 0.75~1.53.03
10.6310.09.08.07.06.05.04.03.53.02.52.01.80.83 (4.91m)1.031.231.431.732.132.430.73 0.53 (6.83m)0.630.931.081.281.53
0.41 0.33 (8.73m)0.360.480.580.730.830.930.20 0.18 0.180.230.260.300.380.48
1.73 (2.20m)
0(m) 1 2 3 4 5 6 7 8 9 10
RATED LOAD
Working Radius
Heig
ht A
bove
Gro
und
76̊
10 2 3 4 5 6 7 (8.73)(0.75)
(10.1)
3456789
21
(m)
(m)
70̊60̊
40̊30̊
20̊
10̊
1˚
50̊Maximum Working Radius 8.73m. W294
4 Sections Boom
Working Radius 1.60.75 ~3.03
8.738.07.06.05.04.03.53.02.52.01.80.83 (4.93m)1.081.251.481.832.282.550.78 0.58 (6.83m)0.630.981.131.331.63
0.43 0.380.530.630.780.88 33.089.01.88 (2.20m)
0(m) 1 2 3 4 5 6 7 8
RATED LOAD
Maximum Working Radius 6.43m. W2933 Sections Boom
Working Radius 1.60.66 ~3.03
6.436.05.04.03.53.02.52.01.80.93 (4.55m)1.081.251.481.832.282.550.78 0.63 0.580.981.131.331.631.88 (2.20m)
0(m) 1 2 3 4 5 6
Working Radius
Heig
ht A
bove
Gro
und
20 1 3 4 5 (6.43)(0.66)
4567
(7.9)
321
(m)
(m)
76̊ 70̊60̊
40̊30̊20̊10̊1˚
50̊
RATED LOAD
15
URW340 series
SPECIFICATIONS
CRANE MODEL URW342 URW343 URW344Max lifting capacity 3030kg at 2.7m 3030kg at 2.7m 3030kg at 2.6m
Max working radius 5.32m 7.51m 9.81m
Max hook height (approx.)
Above ground 7.3m 9.5m 11.7m
Below ground 6.1m with 4-part line 8.7m with 4-part line 11.5m with 4-part line
Boom length Min 3.27m, Max 5.51m Min 3.31m, Max 7.7m Min 3.41m, Max 10.0m
Boom sections 2-section box beam type telescoping boom
3-section box beam type telescoping boom
4-section box beam type telescoping boom
Boom raise angle 1° to 78°
Slewing angle 360° continuous
Winch
Single line pull 7.35kN {750kgf}
Wire rope
Construction: IWRC 6 x WS(26) GRADE B /
Diameter x Length: 8mm x 40m / Breaking strength:
42.4kN {4320kgf}
Construction: IWRC 6 x WS(26) GRADE B /
Diameter x Length: 8mm x 51m / Breaking strength:
42.4kN {4320kgf}
Construction: IWRC 6 x WS(26) GRADE B /
Diameter x Length: 8mm x 62.5m / Breaking strength:
42.4kN {4320kgf}
Outriggers
Vertical jacks, double acting hydraulic cylinders with pilot-operated check valves / Horizontal beams, manual extension type
Retracted: 2.0m, Extended 3.5m, Mid-extended: 2.7m
Hydraulic pump Rated pressure 20.6MPa {210kgf/cm2}
Hydraulic oil tank capacity 32L
Safety devices
Pressure relief valve for hydraulic circuit / Counterbalance valves for boom raising and boom telescoping cylinders / Pilot-operated check valves for vertical outrigger cylinders / Boom angle indicator with load indicator / Hook safety latch / Automatic mechanical brake for winch / Digital load meter / Automatic stop for overwinding / Overwinding alarm / Alarm
buzzer / Level / Emergency stop button / Overloading alarm / Turnover protection
3,030 kgLIFTING CAPACITY
APPROX.11.7 mMAX. HOOK HEIGHT
ABOVE GROUND
RADIOREMOTE
CONTROL
16
ROTATION CENTER
STROKE750
STROKE750
215
215
470
MAX3,500
MID2,700
MIN2,000
TRUCK FRAME
1,760
STROKE475
195
332972.5
497.5
232
195195
25
400
350
230
475
230
2,150
CRANE MOUNTING DIMENSIONS
CRANE MODEL
UR-W344 3,594 Min. 3,410 ~ Mid. 5,650 ~ 7,825 ~ Max. 10,000 2,095 2,095
UR-W343 3,494 Min. 3,310 ~ Mid. 5,550 ~ Max. 7,700 2,092 2,095
UR-W342 3,454 Min. 3,630 ~ Max. 5,510 2,092 2,095
Drawing: UR-W344 (Unit: mm)
12
3 4
1 2 3 4
(m)Working Radius
Heig
ht A
bove
Gro
und
10 2 3 4 5 6 7 8 9 (9.81)(0.67)
(m)(11.7)
11109876543
78 7060
50
40
20
30
10
121
Maximum Working Radius 9.81m.
Working Radius 9.818.07.06.05.55.04.54.03.53.02.70.67 ~ 2.6
W344
81.130.3 (5.46m)1.481.681.982.33 82.136.21.081.231.431.732.132.33
0.730.68(7.63m)0.880.98 0.73
0.63 0.560.83 0.780.931.03
9.0
0.50 0.48
4 Sections Boom
0(m) 1 2 3 4 5 6 7 8 9
RATED LOAD
Working Radius
Heig
ht A
bove
Gro
und
10 2 3 4 5 6 7(7.51)(0.65)
(m)
(m)(9.5)
9876543
78 7060
5040
20
30
101
21
Maximum Working Radius 7.51m.
Working Radius 7.516.05.55.04.54.03.53.02.70.65 ~ 2.6
W343
82.130.3 (5.36m)1.531.732.032.48 33.130.31.131.281.481.782.13
7.0
0.7339.033.2 1.03 0.68
3 Sections Boom
0(m) 1 2 3 4 5 6 7
RATED LOAD
Working Radius
Heig
ht A
bove
Gro
und
10 2 3 4 5 (5.32)(0.65)
(m)
(m)(7.3)
76543
7060
5040
2030
101
21
78
Maximum Working Radius 5.32m.
Working Radius 5.325.04.54.03.53.02.70.65 ~ 2.5
W342
33.185.130.3 1.782.082.53 83.130.3
2 Sections Boom
0(m) 1 2 3 4 5
RATED LOAD
17
URW370 series
SPECIFICATIONS
3,030 kgLIFTING CAPACITY APPROX.16.2 m
MAX. HOOK HEIGHTABOVE GROUND
CRANE MODEL URW373 URW374 URW375 URW376Max lifting capacity 3030kg at 2.7m 3030kg at 2.6m 3030kg at 2.4m 3030kg at 2.4m
Max working radius 7.51m 9.81m 12.11m 14.42m
Max hook height (approx.)
Above ground 9.5m 11.7m 14.0m 16.2m
Below ground 8.7m with 4-part line 11.5m with 4-part line 14.3m with 4-part line 17.1m with 4-part line
Boom length Min 3.31m, Max 7.7m Min 3.41m, Max 10.0m Min 3.54m, Max 12.3m Min 3.63m, Max 14.61m
Boom sections 3-section box beam type telescoping boom
4-section box beam type telescoping boom
5-section box beam type telescoping boom
6-section box beam type telescoping boom
Boom raise angle 1° to 78°
Slewing angle 360° continuous
Winch
Single line pull 7.35kN {750kgf}
Wire rope
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 51m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 62.5m/Breaking strength: 42.4kN {4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 73.5m/Breaking strength: 42.4kN {4320kgf}
Construction: IWRC 6 x WS(26) GRADE B/Diameter x Length:
8mm x 85m / Breaking strength: 42.4kN
{4320kgf}
Outriggers
Vertical jacks, double acting hydraulic cylinders with pilot-operated check valves / Horizontal beams, manual extension type
Retracted: 2.02m, Extended: 4.2m, Mid-extended: 2.7m, 3.4m
Hydraulic pump Rated pressure 20.6MPa {210kgf}
Hydraulic oil tank capacity 32L
Safety devices
Pressure relief valve for hydraulic circuit / Counterbalance valves for boom raising and boom telescoping cylinders / Pilot-operated check valves for vertical outrigger cylinders / Boom angle indicator with load indicator / Hook safety latch / Automatic mechanical brake for winch / Digital load meter / Automatic stop for overwinding / Overwinding alarm / Alarm
buzzer / Level / Emergency stop button / Overloading alarm / Turnover protection
RADIOREMOTE
CONTROL
18
195195
25
ROTATION CENTER
STROKE1,090
STROKE1,090
400
350
340
230
230
475
215
215
470
2,150MAX
4,200
MID(2)3,400MID(1)2,700
MIN2,020
195
STROKE472
332
983.5
1,760
511.5
232
TRUCK FRAME
CRANE MOUNTING DIMENSIONSCRANE MODEL
UR-W376 3,814 Min. 3,630 ~ Mid. 5,850 ~ 8,040 ~ 10,230 ~ 12,420 ~ Max. 14,610 2,114 2,212
UR-W375 3,724 Min. 3,540 ~ Mid. 5,780 ~ 7,980 ~ 10,140 ~ Max. 12,300 2,136 2,134
UR-W374 3,594 Min. 3,410 ~ Mid. 5,650 ~ 7,825 ~ Max. 10,000 2,095 2,095
UR-W373 3,494 Min. 3,310 ~ Mid. 5,550 ~ Max. 7,700 2,092 2,095
Drawing: UR-W374 (Unit: mm)
12
3 4
1 2 3 4
Working Radius
Heig
ht A
bove
Gro
und
10 2 3 4 5 6 7 8 9 10 11 12 13 (14.42)(0.73)
1514131211109876543
78̊70̊
60̊
50̊
40̊
20̊
30̊
10̊
1˚
(16.2)(m)
21
(m)
Maximum Working Radius 14.42m.
Working Radius 9.0 10.0 11.0 12.0 13.0 14.428.07.06.05.55.04.54.03.53.02.72.50.73 ~ 2.4
W376
3.03 1.08(5.66m)1.431.631.932.282.53 52.187.21.051.191.381.682.032.23
0.730.63(7.85m)
0.43(10.04m)0.23(12.23m)
0.830.93 0.680.63 0.53 0.480.83 0.780.931.03
0.31 0.28 0.250.480.63 0.55 0.350.400.33(4.90m) 0.21 0.19 0.17 0.16 0.14 0.130.280.30 0.230.25
6 Sections Boom
0(m) 1 2 3 4 5 6 7 8 9 10 11 12 13 14
RATED LOAD
Working Radius
Heig
ht A
bove
Gro
und
10 2 3 4 5 6 7 8 9 10 11(12.11)(m)(0.71)
(m)(14.0)
131211109876543
78̊ 70̊60̊
50̊
40̊
20̊
30̊
10̊
1˚
21
Maximum Working Radius 12.11m.
Working Radius 9.0 10.0 11.0 12.118.07.06.05.55.04.54.03.53.02.72.50.71 ~ 2.4
W375
3.03 1.13(5.59m)1.431.631.932.282.58 52.187.21.051.201.381.682.032.23
0.730.63(7.79m)
0.46(9.95m)0.830.93 0.68
0.63 0.53 0.480.83 0.780.930.76
1.030.31 0.28 0.25 0.250.480.63 0.55 0.40 0.35
5 Sections Boom
0(m) 1 2 3 4 5 6 7 8 9 10 11
RATED LOAD
Working Radius
Heig
ht A
bove
Gro
und
10 2 3 4 5 6 7 8 9 (9.81)(0.67)
(m)
(m)(11.7)
11109876543
78̊ 70̊60̊
50̊
40̊
20̊
30̊
10̊
1˚
21
Maximum Working Radius 9.81m.
Working Radius 9.818.07.06.05.55.04.54.03.53.02.70.67 ~ 2.6
W374
81.130.3 (5.46m)1.481.681.982.33 82.136.21.081.231.431.732.132.33
0.730.68(7.63m)0.880.98 0.73
0.63 0.56 0.480.83 0.780.931.03
9.0
0.50
4 Sections Boom
0(m) 1 2 3 4 5 6 7 8 9
RATED LOAD
Working Radius
Heig
ht A
bove
Gro
und
10 2 3 4 5 6 7(7.51)(0.65)
(m)
(m)(9.5)
9876543
78̊ ˚7060̊
50̊40̊
20̊
30̊
10̊1˚
21
Maximum Working Radius 7.51m.
Working Radius 7.516.05.55.04.54.03.53.02.70.65 ~ 2.6
W373
82.130.3 (5.36m)1.531.732.032.48 33.130.31.131.281.481.782.13
7.0
0.7339.033.2 1.03 0.68
3 Sections Boom
0(m) 1 2 3 4 5 6 7
RATED LOAD
19
URW500 series
SPECIFICATIONS
CRANE MODEL URW503 URW504 URW505 URW506Max lifting capacity 3030kg at 4.1m 3030kg at 4.1m 3030kg at 3.9m 3030kg at 3.9m
Max working radius 8.1m 10.6m 13.12m 15.47m
Max hook height (approx.)
Above ground 10.5m 13.0m 15.1m 17.6m
Below ground 9.4m with 4-part line 12.5m with 4-part line 15.5m with 4-part line 18.4m with 4-part line
Boom length Min 3.51m, Max 8.34m Min 3.57m, Max 10.84m Min 3.75m, Max 13.35m Min 3.93m, Max 15.71m
Boom sections 3-section box beam type telescoping boom
4-section box beam type telescoping boom
5-section box beam type telescoping boom
6-section box beam type telescoping boom
Boom raise angle 1° to 78°
Slewing angle 360° continuous
Winch
Single line pull 7.35kN {750kgf}
Wire rope
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 55m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 68m / Breaking strength: 42.4kN
{4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 81.5m / Breaking strength: 42.4kN {4320kgf}
Construction: IWRC 6 x WS(26) GRADE B / Diameter x Length:
8mm x 91.5m / Breaking strength: 42.4kN {4320kgf}
Outriggers
Vertical jacks, double acting hydraulic cylinders with pilot-operated check valves / Horizontal beams, manual extension type
Retracted: 2.19m, Extended: 4.8m, Mid-extended: 3.3m, 4.3m
Hydraulic pump Rated pressure 20.6MPa {210kgf}
Hydraulic oil tank capacity 60L
Safety devices
Pressure relief valve for hydraulic circuit / Counterbalance valves for boom raising and boom telescoping cylinders / Pilot-operated check valves for vertical outrigger cylinders / Boom angle indicator with load indicator / Hook safety latch / Automatic mechanical brake for winch / Digital load meter / Automatic stop for overwinding / Overwinding alarm / Alarm
buzzer / Level / Emergency stop button / Overloading alarm / Turnover protection
3,030 kgLIFTING CAPACITY
APPROX.17.6 mMAX. HOOK HEIGHT
ABOVE GROUND
RADIOREMOTE
CONTROL
20
STROKE565
TRUCK FRAME
301352
642
1,938
240
ROTATION CENTER
STROKE805
MAX3,800
MID3,000
MIN2,190
STROKE805
26
240
405
400
250250
520 2,370
240
CRANE MOUNTING DIMENSIONS
CRANE MODEL
UR-W506 4,139 Min. 3,930 ~ Mid. 6,330 ~ 8,720 ~ 11,050 ~ 13,380 ~ Max. 15,710 2,398 2,535
UR-W505 3,959 Min. 3,750 ~ Mid. 6,150 ~ 8,550 ~ 10,950 ~ Max. 13,350 2,359 2,363
UR-W504 3,779 Min. 3,570 ~ Mid. 6,000 ~ 8,420 ~ Max. 10,840 2,312 2,319
UR-W503 3,720 Min. 3,510 ~ Mid. 5,940 ~ Max. 8,340 2,312 2,319
Drawing: UR-W504 (Unit: mm)
12
3 4
1 2 3 4
10 2 3 4 5 6 7 8 9 101112 13 (15.47)(0.73)
(17.6)
2345678910111213141516
Working Radius
Heig
ht A
bove
Gro
und
(m)
(m)
1
Maximum Working Radius 15.47m.
W5066 Sections Boom
0(m) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Working Radius 15.4713.0 14.012.011.010.09.08.07.06.05.55.04.52.43 2.13 1.88 1.63 1.332.03 1.83 1.65 1.48 1.23 1.03 0.88 0.78 0.73 (10.81m)
1.33 1.20 1.10 0.95 0.83 0.73 0.65 0.60 0.550.53 0.43 0.38 0.38 0.33 0.33 0.28 0.28 0.25 0.23
0.50 (13.14m)
1.03 (8.48m)0.73 ~ 3.9
3.03
RATED LOAD
(15.4)
234567891011121314
10 2 3 4 5 6 7 8 9 10 11 (13.12)(0.70) Working Radius
Heig
ht A
bove
Gro
und
(m)
(m)
1
Maximum Working Radius 13.12m. W505
5 Sections Boom
Working Radius 13.1212.011.010.09.08.07.06.05.55.04.52.43 2.13 1.88 1.65 1.332.03 1.83 1.65 1.48 1.23 1.03 0.88 0.78 0.73 (10.71m)
1.33 1.20 1.10 0.95 0.83 0.73 0.65 0.60 0.55 0.50
1.08 (8.31m)0.70 ~ 3.9
3.03
0(m) 1 2 3 4 5 6 7 8 9 10 11 12 13
RATED LOAD
(13.0)
23456789101112
10 2 3 4 5 6 7 8 9 (10.60)(0.67) Working Radius
Heig
ht A
bove
Gro
und
(m)
(m)
1
Maximum Working Radius 10.60m. W5044 Sections Boom
Working Radius 10.6010.09.08.07.06.05.55.04.52.58 2.28 1.93 1.73 1.402.03 1.83 1.65 1.48 1.23 1.08 0.98 0.85 0.83
1.13 (8.18m)0.67 ~ 4.1
3.03
0(m) 1 2 3 4 5 6 7 8 9 10
RATED LOAD
456789
(10.5)
32
10 2 3 4 5 6 7(8.10)(0.66) Working Radius
Heig
ht A
bove
Gro
und
(m)
(m)
1
Maximum Working Radius 8.10m. W5033 Sections Boom
Working Radius 8.107.06.05.55.04.52.58 2.28 2.00 1.73 1.43 1.23
0.66 ~ 4.13.03
0(m) 1 2 3 4 5 6 7 8
RATED LOAD
21
URW540 series
SPECIFICATIONS
CRANE MODEL URW543 W/WY
URW544 W/WY
URW545 W/WY
URW546 W/WY
URW547 W/WY
Max lifting capacity 4050kg at 2.9m 4050kg at 2.9m 4050kg at 2.9m 4050kg at 2.9m 4050kg at 2.9m
Max working radius 8.1m 10.6m 13.12m 15.47m 17.78m
Hook height (approx.)
Above ground 10.3m 12.7m 15.1m 17.4m 19.8m
Below ground 9.4m with4-part line
12.5m with 4-part line
15.5m with 4-part line
18.4m with 4-part line
21.5m with 4-part line
Boom length Min 3.51mMax 8.34m
Min 3.57mMax 10.84m
Min 3.75mMax 13.35m
Min 3.93mMax 15.71m
Min 3.99mMax 18.02m
Boom sections3-section box beam type
telescoping boom
4-section box beam type
telescoping boom
5-section box beam type
telescoping boom
6-section box beam type
telescoping boom
7-section box beam type
telescoping boom
Boom raise angle 1° to 78°
Slewing angle 360° continuous
Winch
Single line pull 9.80kN {1000kgf}
Wire rope
Construction: IWRC 6 x
WS(26) GRADE B / Diameter x Length: 8mm x 55m / Breaking strength: 47.4kN
{4800kgf}
Construction: IWRC 6 x
WS(26) GRADE B / Diameter x Length: 8mm x 68m / Breaking strength: 47.4kN
{4800kgf}
Construction: IWRC 6 x
WS(26) GRADE B / Diameter x Length: 8mm x
81.5m / Breaking strength: 47.4kN
{4800kgf}
Construction: IWRC 6 x
WS(26) GRADE B / Diameter x Length: 8mm x
91.5m / Breaking strength: 47.4kN
{4800kgf}
Construction: IWRC 6 x
WS(26) GRADE B / Diameter x Length: 8mm x
103m / Breaking strength: 47.4kN
{4800kgf}
Outriggers
Vertical jacks, double acting hydraulic cylinders with pilot-operated check valves / Horizontal beams, manual extension type
Retracted: 2.19m, Extended: 4.8m, Mid-extended: 3.3m, 4.3m
Hydraulic pump Rated pressure 20.6MPa {210kgf/cm2}
Hydraulic oil tank capacity 60L
Safety devices
Pressure relief valve for hydraulic circuit / Counterbalance valves for boom raising and boom telescoping cylinders / Pilot-operated check valves for vertical outrigger cylinders / Boom angle indicator with load indicator / Hook safety latch / Automatic mechanical brake for winch / Digital load meter / Automatic stop for overwinding / Overwinding alarm / Alarm
buzzer / Level / Emergency stop button / Overloading alarm / Turnover protection
4,050 kgLIFTING CAPACITY
APPROX.19.8 mMAX. HOOK HEIGHT
ABOVE GROUND
RADIOREMOTE
CONTROL
22
CRANE MOUNTING DIMENSIONS
240
1,945
645 342293
STROKE 565
SLEWING CENTER 2505 00 555
STROKE 1,305 MAX: 4,800 / MID2: 4,300 / MID1: 3,300 / MIN: 2,192 STROKE 1,305
CRANE MODEL
UR-W546W/WY 4,134 Min. 3,930 ~ Mid. 6,330 ~ 8,720 ~ 11,050 ~ 13,380 ~ Max. 15,710 2,405 2,545
UR-W545W/WY 3,959 Min. 3,750 ~ Mid. 6,150 ~ 8,550 ~ 10,950 ~ Max. 13,350 2,366 2,370
UR-W544W/WY 3,779 Min. 3,570 ~ Mid. 6,000 ~ 8,420 ~ Max. 10,840 2,319 2,326
Drawing: UR-W546W/WY(Unit: mm)
12
3 4
1 2 3 4
Working Radius 0.67 ~ 2.9 3.5 4.1 4.5 5.0 5.5 6.0 7.0 8.0 9.0 10.0 10.6
4.05 3.50 (3.33m)
4.05 3.35 3.05 2.60 2.30 1.95 1.8 (5.76m)
3.05 3.05 3.05 2.60 2.30 1.95 1.75 1.45 1.15 (8.18m)
2.05 2.05 2.05 1.85 1.70 1.50 1.25 1.10 1.00 0.90 0.85
Working Radius 0.70 ~ 2.9 3.5 4.0 4.5 5.0 5.5 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.12
4.05 3.35 (3.51m)
4.05 3.35 3.05 (3.9m) 2.45 2.15 1.90 1.70 (5.91m)
3.05 3.05 3.05 (3.9m) 2.45 2.15 1.90 1.70 1.35 1.10 (8.31m)
2.05 2.05 1.85 1.70 1.50 1.25 1.05 0.90 0.80 0.75 (10.71m)
1.35 1.35 1.25 1.15 1.00 0.85 0.75 0.70 0.65 0.60 0.55
Working Radius 0.73 ~ 2.9 3.5 4.0 4.5 5.0 5.5 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.47
4.05 3.35 3.20 (3.69m)
4.05 3.35 3.05 (3.9m) 2.45 2.15 1.90 1.65 (6.09m)
3.05 3.05 3.05 (3.9m) 2.45 2.15 1.90 1.65 1.35 1.05 (8.48m)
2.05 2.05 1.85 1.70 1.50 1.25 1.05 0.90 0.80 0.75 (10.81m)
1.35 1.35 1.25 1.15 1.00 0.85 0.75 0.70 0.65 0.60 0.55 (13.14m)
0.55 0.45 0.40 0.40 0.35 0.35 0.30 0.30 0.30 0.25
Maximum Working Radius 15.47m.
W546W/WY6 Sections Boom
RATED LOAD
Maximum Working Radius 13.12m.
W545W/WY5 Sections Boom
RATED LOAD
Maximum Working Radius 10.60m.
W544W/WY4 Sections Boom
RATED LOAD
23
URU800 series
SPECIFICATIONS
CRANE MODEL URU805Max lifting capacity 8,200kg at 2.5m
Max working radius 15.6m
Max hook height (approx.)
Above ground 17.5m
Below ground 17.7m with 6-part line
Boom length Min 4.4m to Max 15.9m
Boom sections 5-section box beam type telescoping boom
Boom raise angle 1° to 80°
Slewing angle 360° continuous
WinchSingle line pull 1,640kg 13.1kN {1333kgf}
Wire rope Construction: IWRC 6 x WS(29) GRADE B / Diameter x Length: 9mm x 129m / Breaking strength: 68.6kN {7000kgf}
Outriggers
Vertical jacks, double acting hydraulic cylinders with pilot-operated check valves / Horizontal beams, manual extension type
Retracted: 2.26m, Extended: 5.1m
Hydraulic pump Rated pressure 20.6MPa {210kgf/cm2}
Hydraulic oil tank capacity 90L
Safety devices
Pressure relief valve for hydraulic circuit / Counterbalance valves for boom raising and boom telescoping cylinders / Pilot-operated check valves for vertical outrigger cylinders / Boom angle indicator with load indicator / Hook safety latch / Automatic mechanical brake for winch / Digital load meter / Automatic stop for overwinding / Overwinding alarm / Alarm buzzer / Level / Emergency stop button / Overloading alarm / Turnover protection
8,070 kgLIFTING CAPACITY
APPROX.17.5 mMAX. HOOK HEIGHT
ABOVE GROUND
RADIOREMOTE
CONTROL
24
CRANE MOUNTING DIMENSIONS
CRANE MODEL
URU-805-AU 4,525 Min. 4,400 ~ Mid. 7,300 ~ 10,200 ~ 13,000 ~ Max. 15,900 2,424 2,458
Drawing: URU-805-AU(Unit: mm)
1,93
8
(176
7)
654
605
300
220
111300
(597)(473)
SLEWING CENTER
12
3 4
1 2 3 4
Working Radius 2.0 2.5 2.7 3.0 3.5 4.0 4.5 5.0 5.5 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 15.6
8.07 8.07 7.07 6.07 5.17 4.47 (4.10m)
6.07 6.07 6.07 6.07 5.17 4.57 4.12 3.67 3.32 2.97 2.37
3.07 3.07 3.07 3.07 3.07 3.07 3.07 3.07 2.87 2.37 1.97 1.72 1.57 (10.1m)
2.67 2.67 2.67 2.67 2.67 2.67 2.67 2.12 1.72 1.52 1.32 1.17 1.02 0.92 (12.7m)
2.07 2.07 2.07 2.07 2.07 2.07 1.97 1.72 1.52 1.32 1.17 1.02 0.87 0.77 0.67 0.57
URU-805-AU5 Sections Boom
Maximum Working Radius 15.6m.
RATED LOAD
4
220
STROKE 1,420 STROKE 1,420MAX: 5,100 / MIN: 2,260
LEGAL
SPECIFICATION CHANGES
Furukawa Unic Corporation reserves the right to make changes in manufacturing to comply with current or new engineering specifi cation changes where applicable.
INSTALLATION COMPLIANCE
Before installing any crane, please observe the Vehicle Loading Limitations and stability of the crane/truck combination. Australian Standard AS1418.11 provides guidance for the installation, testing and certifi cation of Vehicle Loading Cranes.
IMPORTANT NOTES
Trademarks are property of their respective owners.
Detailed product specifi cations can be found at www.uniccrane-global.com.
All measurements using the metric system, unless otherwise specifi ed.