QUOLIS 5000 DENTAL UNIT
INSTALLATION INSTRUCTIONS
IMPORTANT
This manual provides installation instructions for the BELMONT QUOLIS5000 UNIT. The instructions contained in this booklet should be thoroughly read and understood before installing the chair and unit.After the installation has been completed, keep this manual in a safe place and refer to it for future maintenance.
R
Intended Use of the Product This product is an active therapeutic device intended to administer or exchange energy of electric, air
and water for the exclusive use for diagnoses, treatments and relative procedures of dentistry, and its
characteristic is not in a potentially hazardous way between such energy and human body, taking
account of the nature, the density and site of application of the energy.
The product must be operated or handled by the qualified dentists or by dental staffs under the
supervision of the dentist.
Such dentists or dental staffs should instruct and/or assist the patients to approach to and leave from
the product.
Patients should not be allowed to operate or handle the product unless he/she is so instructed.
The product is supplied together with the handpieces like electric micromotor, air turbine and/or
motor, scaler and so on.
Environmental Requirements Ambient Temperature Operating 41F to 104F Storage 14F to 122F
Humidity 10 % - 80%
Atmospheric Pressure 8.7psi – 15.4psi
Classification of Eqipment a. Type of shock protection : Class I Equipment
b. Degree of shock protection : Type B Applied part
c. Degree of protection against water ingress : Ordinary Equipment (All Products)
d. Mode of operation : Continuous Operation
e. Flammable Gasses : Not suitable for use in the presence of a flammable anesthetic mixture with air,
oxygen, or nitrous oxide.
f. Earth : Protective earth (ground)
g. Hospital Grade Plug : Grounding reliability can be achieved only when the equipment is connected to an
equivalent receptacle marked hospital only or hospital grade.
CAUTION
Ground reliability can only be achieved when the equipment is connected to an equivalent receptacle marked HOSPITAL only or HOSPITAL GRADE.
TABLE OF CONTENTS Page 1 . Overview and Major Components ----------------------------------------- 1 1-1. Vac Pac System 1-2. PMU System 2.DimensionsandSpecifications ----------------------------------------------- 3 2-1. Vac Pac System 2-2. PMU System 3 . Introduction -------------------------------------------------------------------- 5 3-1. Precautions 3-2. Necessary tools 4 . Unpacking of Units ------------------------------------------------------------ 5 5 . Swing Arm ---------------------------------------------------------------------- 7 5-1. How to Install the Swing Arm 6 . Junction Box -------------------------------------------------------------------- 7 6-1. How to Install the Junction Box 7 . Balance Arm for the Doctor’ s Control ----------------------------------- 8 7-1. How to Install the Balance Arm 7-2. How to Plumb the Doctor’ s Control 7-3. How to Plumb the Water Bottle 7-4. How to Install the Foot Control 8 . Monitor Mount (Optional) -------------------------------------------------- 11 8-1. How to Install the Monitor Arm 9 . Light Pole (Optional) --------------------------------------------------------- 12 9-1. How to Install the Light Pole (Optional) 10 . Vac Pac (Optional) ------------------------------------------------------------- 12 10-1. How to Install the Vac Pac 10-2. How to Plumb the J-Box Utility 11 . PMU (Optional) --------------------------------------------------------------- 14 11-1. How to Install the PMU 11-2. How to Install the Cuspidor Bowl 11-3. How to Plumb the J-Box Utility 11-4. How to install accessories 12 . Final Adjustment --------------------------------------------------------------- 17 12-1. Swing Arm 12-2. How to Adjust the Swing Arm Friction 12-3. How to Adjust the Rotation Tension of Assistant Arm 12-4. How to adjust the water flow volume of Cup fill and Bowl Rins13.ConnectthePowerCableandConfirmsfunctionlity ------------------ 18 14 . Option --------------------------------------------------------------------------- 18 14-1. How to Install the Tray Holder 15 . Flow Diagram ------------------------------------------------------------------- 19 15-1. Doctor’ s Table Section 15-2. Swing Arm Section 15-3. Vac Pac Section 15-4. PMU Section 15-5. Junction Box Section 15-6. Overall Unit Flow Diagram(Vac Pac System) 15-7. Overall Unit Flow Diagram(PMU System) 16 . Electrical Diagram ----------------------------------------------------------- 25 16-1. Chair Section 16-2. Doctor’s Table Section 16-3. PMU Section 17 . Location of Product Labels ------------------------------------------------- 28 18 . Floor Template ---------------------------------------------------------------- 29
14
15
16
24
17 1918
21
2223
20
1
2
34
78
9
10
11
12
13
56
1. Overview and Major Components 1-1. Vac Pac System
(1) Control Head
(2) Main Control Panel
(3) Digital Display
(4) Handle
(5) Handpiece Holders
(6) Dr’s Syringe
(7) Handpiece Hose
(8) Foot Control
(9) Balance Arm
(10) Dr Swing Arm]
(11) Water Bottle
(12) Junction Box
(13) Dental Light Swing Arm
(14) Light Pole
(15) Assistant Instrument Holder
(16) HVE
(17) SE
(18) Assistant’s Syringe
(19) Assistant Touch Pad
(20) Solids Collector
(21) Assistant Swing Arm
(22) Assistant Holder Arm
(23) Vacuum Pack Housing
(24) Dental Light
(*Note) Quolis 5000 series does not include syringe tips. Syringe tips manufactured by DCI are
compatible with this device.
- 1 -
14
15
16
24
17
19
18
21
22
2320
1
2
34
7
8
9
10
11
1213
5 6
25 2627
28
1. Overview and Major Components 1-2. PMU System
(1) Control Head
(2) Main Control Panel
(3) Digital Display
(4) Handle
(5) Handpiece Holders
(6) Dr’s Syringe (*)
(7) Handpiece Hose
(8) Foot Control
(9) Balance Arm
(10) Dr Swing Arm
(11) Water Bottle
(12) Junction Box
(13) Dental Light Swing Arm
(14) Light Pole
(15) Assistant Instrument Holder
(16) HVE
(17) SE
(18) Assistant’s Syringe (*)
(19) Assistant Touch Pad
(20) Solids Collector
(21) Assistant Swing Arm
(22) Assistant Holder Arm
(23) Assistant Section
(24) Dental Light
(25) Cuspidor Bowl
(26) Cup filler switch and Bowl Rinse switch
(27) Cup filler nozzle and Bowl Rinse nozzle
(28) Q.D.Section
(*Note) Quolis 5000 series does not include syringe tips. Syringe tips manufactured by DCI are
compatible with this device.
- 2 -
2. Dimensions and Specifications 2-1. Vac Pac System 2-1-1. Dimensions - Inch / (mm) - Tolerance (± 10%)
2-1-2. Specifications Power Consumption ------------------------------- AC120V 1A Frequency ------------------------------------------- 60 Hz Fuse value ------------------------------------------- AC125V 10A Control Voltage ------------------------------------- DC5V Dr’s control Net Weight --------------------------- 55 lbs (25 kg) Swing Arm Net Weight ---------------------------- 55 lbs (25 kg) (Without Dental Light) Vacuum Pack Net Weight ------------------------- 44 lbs (20 kg) Junction Net Weight ------------------------------- 16 lbs (7 kg) Doctor Table Maximum Load -------------------- 4.40 lbs (2 kg) Operating Pressure --------------------------------- Water 30-40 psi (0.2-0.28 Mpa), Air 75 psi (0.5 MPa)
- 3 -
2. Dimensions and Specifications 2-2. PMU System 2-2-1. Dimensions - Inch / (mm) - Tolerance (± 10%)
2-2-2. Specifications Power Consumption ------------------------------- AC120V 1A Frequency ------------------------------------------- 60 Hz Fuse value ------------------------------------------- AC125V 10A Control Voltage ------------------------------------- DC5V Dr’s control Net Weight --------------------------- 55 lbs (25 kg) Swing Arm Net Weight ---------------------------- 55 lbs (25 kg) (Without Dental Light) PMU Net Weight ----------------------------------- 66 lbs (30 kg) Junction Net Weight ------------------------------- 16 lbs (7 kg) Doctor Table Maximum Load -------------------- 4.40 lbs (2 kg) Operating Pressure --------------------------------- Water 30-40 psi (0.2-0.28 Mpa), Air 75 psi (0.5 MPa)
- 4 -
3. Introduction 3-1. Precautions for installation
• Do not connect to power supply other than 120V/60Hz.
• Ground the unit properly.
• Attach the junction box firmly to the floor.
• When electric micromotor (option) or electric scaler (option) is installed, please refer to the manual
for the each device.
• Do not drop or hit the chair.
• When the installation process has been completed, verify that all the mechanical and electrical
functions are working properly and that there is no evidence of oil, water or air leakage.
• Attach the dental chair to the floor before mounting the unit.
• Refer to the installation manual of Quolis 5000 dental chair to know how to install the dental chair.
• Refer to Floor Template for connection of water, air, power, drain hose and vacuum hose.
3-2. Necessary Tools
• Phillips screw drivers set #1, #2.
• Slotted screw driver
• Hex key wenches set (metric, 2.5mm – 8mm)
• Adjustable wrench(over 24mm)
• Long nose pliers
• Wire cutter
• Socket set 17mm, 7mm, 1/4”
• Level
4. Unpacking of units Each carton number corresponds to a component
Check all the components and parts
damage after unpacking.
Opening cartons with a sharp object may cause damage to parts
CAUTION
Box No. Module
3 Doctor’s control
4 Swing arm (s)
5 Vac pacPMU
No. 3No.5
No.4
6
No.6
- 5 -
Box No.3 (Doctor’s control)
(1) Doctor's control assembly 1 set
(2) Junction box assembly 1 set • Junction box with cover 1 set • Duct hose 800mm 1 pc. • Utility package (air)
(3) Balance arm end cap 1pc.
(4) Stainless tray and non-slip pad 1 set
(5) Foot controller 1 set
(6) Syringe parts 1 set
(7) Operating manual, installation manual 1 set
(8) Miscellaneous parts for installation as follow • Sleeve for 1/4” OD tubing 14 pcs. • Sleeve for 1/8” OD tubing 12 pcs. • Barb fitting for 1/4” OD tubing 3 pcs. • Barb fitting for 1/8” OD tubing 3 pc. • Hex plug 2 pcs. • Tubing 1/8” OD brown 500mm 1 pc. • Tubing 1/4 Green 500mm 1 pc. • Panhead Philips screw M4 x 10mm 2 pcs • Round head Philips wood screw M5 x 25mm 3 pcs.
Box No.4 (Swing arms)
(9) Swing arm Assembly 1 set
(10) Water bottle 1 pc
(11) Lower tubing cover 1 pc.
(12) Quick disconnect adaptor for water bottle 1pc.
(13) Swing arm locking pin for dental light 1 pc. (For the swing-
mounted light only)
(14) Miscellaneous Parts for installation as follow. • Socket screw M10 x 40mm (for mounting) 4 pcs. • Socket screw M10 x 20mm (for level) 4 pcs. • Pan head Phillips screw M5 x 16mm 4 pcs. • Flat head screw M10×35mm 1 pc. • 1/4 sleeve 2 pcs. • 1/8 sleeve 1 pc.
Box No.5 (Vac Pac)
(15) Vac Pac Assembly 1 set
(16) Syringe parts 1 set
(17) Miscellaneous Parts for installation as follow. • Socket screw M10 x 40mm (for mounting) 4 pcs. • 1/4 sleeve 2 pcs. • Barb fitting for 1/4 OD tubing 2 pcs.
Box No.6 (PMU)
(18) PMU Assembly 1 set
(19) Junction Box Assembly 1 set
(20) Syringe parts 1 set
(21) Cuspidor Bowl Section
• Cup filler nozzle 1pc.
• Bowl Rinse nozzle 1pc.
• Basket Strainer & Cap 1pc.
(22) Miscellaneous Parts for installation as follow. • Socket screw M10 x 40mm (for mounting) 4 pcs. • 1/4 sleeve 8 pcs. • Barb fitting for 1/4 OD tubing 5 pcs.
(2)
(3), (4), (5) (6)
(16)
(20) (21)
(10) , (11)
(12) , (13)
(19)
- 6 -
5. Swing Arm 5-1. How to Install the Swing Arm The swing arm assembly shall be mounted at the front of the chair under the seat. 1. Raise the seat frame of the chair as shown.
2. Insert M10 x 35mm flat head screw in the threaded hole on the top side of the plate, center . Leave 1" from the top of screw to plate surface.
3. Raise the seat.
4. Attach swing arm assembly to chair by aligning M10 x 35mm screw with recess in front of the seat and slide screw into slot.
5. Locate 4 - M10 x 20mm leveling set screws and insert into bottom side of swing arm plate.
6. Adjust the level of the swing arm plate with the four socket set screws.
7. Tighten the 4 - M10 x 40 mm socket head screws. Lift the swing arm if needed.
6. Junction Box 6-1. How to Install the Junction Box Refer to Floor Template for connection of water, air, power, drain hose and vacuum hose.
1. Raise the chair up
2. Turn off the power of the chair
3. Remove two slotted M5 x 10mm screws from each side of the pump cover and remove pump cover.
4. Place the junction box frame in front of the chair. (The plan of the plumbing position needs to be done in advance. See the flow diagram)
5. Attach the junction box frame to the floor with three M5 x 25mm round head philips wood screws.
Failure to lift seat frame as shown can result in damage to paint finish of swing arm in subsequent steps.
CAUTION Seat Frame
Flat Head Screw
Flange cover
Swing arm plate
4 X Socket head screws (M10 x 40mm) for securing arm assembly to the chair
4 X Socket head screws(M10 x 20mm) for level adjustment
Main SwitchScrews for J.box cover Screws for pump cover
Screws x 3
- 7 -
7. Balance Arm for the Doctor’s Control 7-1. How to Install the Balance Arm
1. Lower the chair.
2. Insert the balance arm into the top of the swing arm.
3. Slide the balance arm cover off balance arm and route tubing and
cables down into the swing arm. Make sure that the hoses are not
twisted.
4. Remove the seat flange cover from chair by removing four M5 x
15mm screws and sub-link cover by
removing two M5 x 15mm screws on the back of the chair
cantilever lift arm.
5. Route umbilical tubing & wires from swing arm into chair. Tubing &
wires should be routed over the top of the pivot bar in the front of
the cantilever arm.
6. Feed umbilical down between 2nd pivot bar and into plastic retaining
loop.
7. Feed tubing between PCB box and pump and out to the front of the chair.
8. Slide in the balance arm cover and into the channels along the balance arm and the
balance arm end cap with two M4 x 10mm screws.
9. Adjust M6 x 5mm balance arm friction
adjustment screw (M6 x 5mm).
Balance arm cover
Flange cover Sub link cover
Main Link Axis
Sub Link Axis
Screws for flange cover
Route tubing and wires over the top of the pivot bar in front of the chair
Feed tubing between PCB box and Pump
Pump
PCB box
Tubing is routed throughthe plastic retainer loop and out thoroug the front of the chair
Balance arm friction adjustment screw
End cap
Screws
- 8 -
7-2. How to Plumb the Doctor’s Control
1. Cut the duct hose to desired length and insert it between retainers inside of the pump cover and the junction box.
CAUTION
If Vac Pac or PMU is installed with Dr. table, run tubings for Vac Pac or PMU at the same time.
AIR
WATER(Optional)
Utility Package
Duct Hose
1/4 Sleeve
1/4 Sleeve
1/8 Sleeve
1/8 Sleeve
Earth(Yellow/Green)
14V/24V Wire(Red/Black/Blue/Purple)
1/8 Tubing (Orange)
1/8 Tubing (Brown)
1/8 Tubing (Blue)
Groundings
3D view of air utility part
Master Air (Orange 1/8”)Pirot Air (Brown 1/8”)
1/4 Tubing (Yellow)
2. Attach the manual on/off valve to the air supply pipe. Purge air through valve to clean debris. Attach automatic valve assembly for air to manual valve. Do the same thingfor the water assembly ordered with "city water" option.
If PMU is not purchased, Utility package for water becomes an option.The pressure gauge for air has higher scale range.
3. As below drawing shows, connect tubings (2,7,8 & 10), connect 14V/24V wire and connect the wire for protective earth (ground).
- 9 -
4. Connect wires in J Box as follows.
(1) Dr.Table and (3) Dr.Table only
(4) PMU only
(2) Dr.Table and Vac Pac
Wiring in J Box
PMU Line
9P
2P
2P
3P
Char Line
Dr.Table Line
Vac Pac Line 9P
2P3P
Chair LineDr.Table Line
Do not connect
Do not connect
Do not connect
9P
2P3P
Chair Line
Dr.Table Line
PMU LineDo not connect
Do not connect
9P
2P2P
2P
3PChair Line
7-3. How to Plumb the Water Bottle
1. Connect the tubing labeled 3, 7 and 11 to the manifold inside the junction box.
Utility package for water is an option. Make sure that City/Bottle
switch is equipped on the Swing Arm.
If City/Bottle switch is not equipped, do not connect green 1/4 tube (11). This will cause water leak.
CAUTION
WATER
1/8 Sleeve1/4 Sleeve
1/4 Sleeve
1/8 Tubing (Brown)1/4 Tubing (Blue)
1/4 Tubing (Green)(Option)
City/Bottle switch
Swing arm
- 10 -
7-4. How to install the Foot Control
Number Color (Size) Function
6 Red (1/4” OD) Drive
10 Yellow (1/4” OD) In
5 Yellow (1/8” OD) Chip (Air for spray, not used)
9 Gray (1/8” OD) Water (Pilot air for water for spray, not used)
1. Insert foot control tubing through channel in chair base
and feed through chairs into J.box.
2. Connect the tubing labeled 5, 6, 9 and 10 to the tubing
from the doctor table.
Note : Although the 1/8” OD gray tubing and yellow 1/8”
OD tubing are not used, connect to prevent air leaks.
3. Attach the foot control tubing to the chair base with a
nylon clamp (see photo).
Drive
Water Pilot Chip
IN
Foot control tbings
1/4 Sleeve
1/4 Tubing (Red)1/8 Tubing (Yellow)1/8 Tubing (Gray)
1/4 Tubing (Yellow)
INDRIVEChipWater Pilot
1/8 Sleeve
8. Monitor Mount(Optional) 8-1. How to Install the Monitor Arm
1. Install the monitor arm to the swing arm. See 5-1 How to install swing arm.
2. Feed the cables thought the swing arm and the chair, and bring the end into the junction box.
3. Install the monitor mount to the monitor arm.
4. Connect the cables inside Junction box.
Note : LCD monitors are not supplied from Belmont. The mounting holes on back of monitor should be
designed for attachment of 75 or 1000 mm VESA mgt pattern.
- 11 -
9. Light Pole (Optional) 9-1. How to Install the Light Pole
1. For installation of the dental light, see the installation and
operation manual of Quolis dental light.
2. Position the swing arm to either side of the chair and lock it in
place with the dental light locking pin.
When you combine Dr. Table and PMU with a water bottle.
Set Lock Pin on A position to avoid the interference of a bottle
and a swing arm.
Locking Pin
< A Position >
CAUTION
Do not remove the cardboard paper put on the swing arm untilthe seat cushion has been attached to the seat frame with screws,otherwise the surface of the light pole will be scratched off whenswinging the arm.
10. Vac Pac(Optional) 10-1. How to Install the Vac Pac
1. Remove four screws M5 x 15mm and the flange cover of the chair.
2. Insert two M10 x 40mm socket head cap screws into the top
threaded hole on the rear side of the chair. Screws should
extend approximately 1" from chair.
3. Hook the assistant arm mounting bracket underneath the two
socket head cap screws.Tilt the bracket slightly and lift it.
Place the lower edge of the mounting bracket on the
projections of the flange.
4. Tighten lower M10 x 40mm socket head cap screws through
swing arm mounting bracket. Tighten all four screws.
5. Route the umbilical tubing with unit umbilical down through
chair, between the main link and sub link Axis, and bring
the end to the junction box. Tie the tubing with the white
nylon clamp.
Make sure that hoses are not kinked
Socket head cap screw
Projections of
approx. 1”
Screw for flange cover
the flange
Tighten
Projection of the flangeMain Link Axis Sub Link Axis
Nylon Clamp
- 12 -
10-2. How to Plumb the JBOX-Utility (Vac Pac)
1. Cut the duct hose to desired length and insert it
between retainers inside of the pump cover and
the junction box.
2. Attach the manual on/off valve to the air supply
pipe.Purge air through valve to clean debris.
Attach automatic valve assembly for air to
manual valve. Do the same thing for the water
assembly ordered with "city water" option.
3. Connect 5/8 Vacuum hose.
4. As below drawing shows, connect
tubings and wires. If connection end is
plugged, use supplied 1/4 fitting.
5. Connect wires under a pump cover.
AIR
WATER(Optional)
Utility Package
Duct Hose
Vacuum
1/4 Sleeve
1/4 Tube Blue
1/4 Sleeve Yellow
Vac Pac Line Chair Line
- 13 -
11. PMU(Optional) 11-1. How to Install the PMU
1. Remove four screws M5 x 15mm and the flange cover of the
chair.
2. Insert two M10 x 40mm socket head cap screws into the top
threaded hole on the rear side of the chair. Screws should
extend approximately 1" from chair.
3. Hook the assistant arm mounting bracket underneath the two
socket head cap screws.
Tilt the bracket slightly and lift it. Place the lower edge of the
mounting bracket on the projections of the flange.
4. Tighten lower M10 x 40mm socket head cap screws through
swing arm mounting bracket. Tighten all four screws.
5. Route the umbilical tubing with unit umbilical down through
chair, between the main link and sub link, and bring the end
to the junction box. Tie the tubing with the white nylon
clamp.
Make sure that hoses are not kinked
Socket head cap screw
Projections of
approx. 1”
Tighten
Main Link Axis Sub Link Axis
Nylon Clamp
Screw for flange cover
the flange
Projection of the flange
- 14 -
11-2. How to Install the Cuspidor Bowl.
1. Take the main cover off by unscrewing
three screws.
2. Remove a cap bolt.
3. Insert Cuspidor Bowl into Rotation Axis.
Do not forget to insert an attached washer.
4. As below drawing shows, connect drain hose, tubings and wires.
(1) We supply long hoses. As needed, cut them accordingly.
(2) To avoid water leak, insert barb fittings to the end.
(Use a connector, when an optional Cuspidor Drain Kit in installed)
(3) Connect the drain hoses by a hose clamp.
(4) Connect tubings by matching colors and numbers.
(5) Connect wirings by using a 4P wire connector.
5. When connections have been completed, put the main cover and cap bolt back.
CAUTION
Please avoid the external force on Drain Hose, tubings and Wires.
This will cause the malfunction or damage to the equipment.
Cuspidor Bowl
Washer
Main Cover
Body
Cap Bolt
hose clamp
Connect tubings
Connect
Cuspidor Drain Valve (Option)
Connect Wirings
1/4 Sleeve
Wire4P Connector
1/4 Tube Blue1/4 Tube Green
- 15 -
11-3. How to Plimb the JBOX-Utility
1. Cut the duct hose to desired length and insert it between retainers inside of the pump cover and the junction box.
2. Attach the manual on/off valve to the air supply
pipe.Purge air through valve to clean debris. Attach automatic valve assembly for air to manual valve. Do the same thing for the water assembly ordered with "city water" option.
3. Connect Vacuum Hose (5/8) and Drain Hose (3/4) Vacuum hose have uneven surface. We supply long hoses. As needed, cut them accordingly.
4. As below drawing shows, connect tubings and
wires. If connection end is plugged, use
supplied 1/4 fitting.Connect Dr. Table side
wirings to the wirings on PMU side.
5. Connect wires in J Box as follows.
AIR
WATER(Optional)
Utility Package
Duct Hose
Drain
Vacuum
1/4 Sleeve
1/8 Sleeve
1/4 Sleeve
1/8 Sleeve
Earth(Yellow/Green)
14V/24V Wire(Red/Black/Blue/Purple)
1/4 Tube Green
1/8 Tube Brown1/8 Tube Orange
1/4Tube Blue
1/8 Tube Brown
1/4 Tube Yellow
Groundings3D view of air utility part
Pirot Air(Brown 1/8”)
Option for PMU onlyDo not Connect
Connect to Dr.Table Line
(1) Dr.Table and PMU
(3) Dr.Table only
(4) PMU only
(2) Dr.Table and Vac Pac
Wiring in J Box
PMU Line
9P
2P
2P
3P
Chair Line
Dr.Table Line
Vac Pac Line 9P
2P3P
Chair LineDr.Table Line
Do not connect
Do not connect
Do not connect
9P
2P3P
Chair Line
Dr.Table Line
PMU LineDo not connect
Do not connect
9P
2P2P
2P
3PChair Line
- 16 -
11-4. Installation of Accessories.
1. Install, Nozzles, Cap & Basket Strainer.Cap
Basket Strainer
Nozzles
12. Final Adjustments 12-1. Swing Arm
1. Attach the lower tubing cover to the bottom of the swing arm mounting bracket with four M5 x 16mm.
2. Replace the chair pump cover and the junction box cover and fasten with M5 x 10mm screw and
tighten firmly with a slotted screw driver.
CAUTION
Fasten the pump cover and junction box cover firmly with a screw driver with screws provided and tighten
12-2. How to Adjust the Swing Arm Friction
The friction of the swing arm for Doctor's control,
dental light and monitor must be adjusted independently.
1. Adjust the M6 x 5mm socket set screw beneath the
swing arm.
12-3. How to Adjust the Rotation Tension of Assistant Arm.
1. Adjusting screw for vertical angle is located here.
To access adjusting screw, pull the rubber cover off.
12-4. How to adjust the water flow volume of Cupfiller and
Bowl Rinse.
1. Adjust the water flow by pinch valves.
Set screw
Set screw
Green : Bowl Rinse
Pinch Valves
Blue : Cupfiller
- 17 -
13. Connect the Power Cable and Confirms functionality. 1. Connect the power cables(120V), electrical cables
and the connectors to the electrical receptacle inside
the junction box for chair and unit.
2. Adjust the regulator pressures. Air : 75 psi. Water (optional) : 30-40psi
3. When all of the installation work are done, turn the main switch on.
Confirms that each part functions correctly.
Then put the cover on.
14. Option 14-1. How to Install the Tray Holder
The tray holder can be mounted at either side of the Doctor's control.
1. Fit the tray holder to the tray arm.
Install the tray arm to beneath the Doctor's control with two
screws M6 x 25mm.
Ground reliability can only be achieved when the
equipment is connected to an equivalent receptacle
marked HOSPITAL only or HOSPITAL GRADE.
CAUTION
ONOFF
Two holes on the back
This can be installed on the other side.
- 18 -
15. Flow Diagram 15-1. Doctor’s control section
- 19 -
15-2. Swing Arm Section
15-3. Vac Pac Section
Air regulatorAir regulator
City / bottle
Option Bottle water City Water (Option)
City / bottle
- 20 -
15-4. PMU Section
Syringe
Ejector
Vacuum
FLOW CONTROL FOR SYRINGE
Air
Water Outlet Flow Control
WATER
AIR
Pinch Valve
Cuspider Bowl
Drain Hose 3/4
Pinch Valve
Vacuum Hose 5/8
Orange 1/8 : Master Air IN(Option)Brown 1/8 : Master Air OUT(Option)Green 1/4 : City Water
Yellow 1/4 : AirBlue 1/4 : Bottled Water
ManifoldSolenoid Valve for Bowl Frash
Solenoid Valve for Water Water
Solid Collector
Bowl Flash Nozzle
Cupfiller Nozzle
Air
Water
- 21 -
15-5. Junction Box Section
AIR
(Drain For PMU only)
VACUUM
WATER (Optional)
Yellow 1/4”OD
Green 1/4”OD
Blue 1/4”OD
Orange 1/8”OD
Blue 1/8”OD
Brown 1/8”OD
- 22 -
15-6. Overall Unit (Vac Pac System)
AIR
(Dra
info
r P
MU
on
ly)
VA
CU
UM
WA
TE
R
(Op
tio
na
l)
- 23 -
AIR
(Dra
info
r P
MU
on
ly)
VA
CU
UM
WA
TE
R
15-7. Overall Unit (PMU System)
- 24 -
16. Electric Diagram
16-1. Chair Section
12
34
56
78
9
84736251
21
21
SV1
SV2
SV4
SV3
1 2 3 4 5 6
12
SV6
98
76
54
32
1
1 2W
hite
Yello
w
XA9P
ANFU
07A0
11
Trun
k Line
B fo
r Sole
noid
Valve
VL2P
Lock
Red
Brow
n
1051 6 2 7 3 8 4 9
CN9
5566
-10A
(MO
LEX)
43
12
VL2P
Fuse
F 10
ABlac
k
Gre
en/Y
ellow
Black
Whit
e
Whit
eBl
ack
LN
CN18
IL-5
P-S3
EN2
(JAE
)
54
32
1
FLAS
H
CN17
IL-7
P-S3
EN2
(JAE
)
76
54
32
1
RY-2
005
(1.2
)
(3.4
)
(2.5
)
(3.4
)
3
11V9V
Trun
k Line
for C
apac
itor
ANFU
12A0
Brow
n
Yello
w
Ora
nge
Red
Gra
y
Purp
le
Blue
Gre
en
CN1-
2(1-
1)IL
-10P
-S3E
N2(J
AE)
109
87
65
344
221
CN13
IL-3
P-S3
EN2
(JAE
)
CN14
IL-3
P-S3
EN2
(JAE
)
CN7
IL-3
P-S3
EN2
(JAE
)
CN6
IL-3
P-S3
EN2
(JAE
)
CN5
IL-3
P-S3
EN2
(JAE
)
CN12
IL-3
P-S3
EN2
(JAE
)321
CN15
IL-2
P-S3
EN2
(JAE
)211
CN2-
2(2-
1)IL
-6P-
S3EN
2(J
AE)
CN1-
1(1-
2)IL
-10P
-S3E
N2(J
AE)
CN16
B03B
-XAS
K-1
CN9
B09B
-XAS
K-1
CN10
IL-1
0P-S
3EN2
(JAE
)
1 2 3 4 5 6
21
1 2 31 2 3
VL8P
56
109
87
65
344
221
1 2 3 1 2 3
Pote
ntio
met
er fo
r Bac
kres
tBr
own
Red
Ora
nge
109
87
65
43
21
Cont
rol P
.C.B
.(AG
FS13
*0)
XX-S
TD20
07/0
0TI
Relay
P.C
.B.
120V
Yello
w
Blac
k do
t ind
icate
s m
ale
pin
side
[Rem
arks
]Co
nnec
tor S
ymbo
l
Cap
Plug
21
Mot
orUp Do
wn
Raise
Recli
ning
Pote
ntio
met
er fo
r Sea
tBr
own
Red
Ora
nge
TSM
-CBC
-5LP
-M1-
E
Tran
sform
erTK
-120
V-2H
Red
Whi
te/R
ed
Brown
SW2
SW3
LIM
NOL
Lim
itST
ORE
EWS
VDA
S20
E53
M
321
1 2 33211 2 3
Capa
citor
45uF
1 5 2 6 3 7 4 8
4
231 6 4 5
2 3 1 2
32
1
54
32
1
CN6
5566
-08A
(MO
LEX)
CN4
B02P
-NV
CN3
B3P-
VH
CN1
B2P-
VH
CN2
B10B
-XAS
K-1N
-ACN
8B0
3B-X
ASK-
1N-A
CN7
B04B
-XAS
K-1N
-A
CN10
5566
-06A
(MO
LEX)
CN5
B04P
-NV
109
87
65
344
221 Brown
544
221
Yello
w
Yello
wAN
FT58
A0Tr
unk L
Ine
for M
otor
/ Ca
pacit
orVL
6P
ANFT
57A0
Tran
sform
er S
ectio
n(12
0V)
ANET
56A0
Mot
or S
ectio
n (1
15V)
ANFT
56A0
ANDR
50A0
ANDR
36A0
Trun
k Line
for R
elay
Sole
noid
Val
ve S
ectio
n(1
20V)
1 2 3 4
Chai
r Dow
n Pr
ohib
ition
Chai
r Ope
ratio
n Pr
ohib
ition
CN4-
1(4-
2)IL
-4P-
S3EN
2(J
AE)
CN8
B04B
-XAS
K-1
12
34
CN3
B05B
-XAS
K-1
SW4
MO
DESW
131
(Pro
porti
onal
Sol
enoi
d Va
lve)
67
89
12
12
34
5
1
Whit
e
Red
10
NMF2
P
N.O.
COM
1 3 2
CN11
5556
-04A
Mai
n Sw
itch
L2
N4
24
Up Down
Raise
Recli
ning
CN2-
1(2-
2)IL
-6P-
S3EN
2(J
AE)
1 2 3 4 5 6
CN19
B05B
-XAS
K-1
3
1 2 3 4
DNCS
42A0
CN4-
1(4-
2)IL
-4P-
S3EN
2(J
AE)
N.O.
COM
Unus
ed
12
CN9
IL-2
P-S3
EN2
(JAE
)
109
87
65
344
221
1112
13
Arm
rest
Mem
bran
e SW
- L(A
GFS
14A0
)
109
87
65
344
221
1112
13
109
87
65
34 4
221
1112
13
109
87
65
34 4
221
1112
1310
98
76
53
4422
111
1213
Dist
ribut
ion
P.C.
B.(A
GFS
12A0
)
(Dist
ribut
ion
P.C.
B. in
the
right
sid
e ar
mre
st)
XA9P
XA2P
Touc
hpad
Swi
tch(A
GFS
16A0
)
To S
eria
l Com
mun
icatio
n Li
ne fo
rDo
ctor
Tabl
e
D Li
ght P
CB.
4
Rota
tion
Lock
EWS
VDA
S20
E53
DNCS
42A0
ANFT
71A0
Mai
n Po
wer S
witch
Sec
tion
ANFT
64A0
Trun
k Li
ne fo
r Den
tal L
ight
Pow
er S
ourc
e
ANFT
65A0
Trun
k Line
ffor
Cha
ir Po
wer S
ourc
e
ANFT
63A0
Earth
ANFT
55B0
XA13
P
XA13
PXA
13P
XA13
PXA
13P
ANFT
60A0
ANFT
61A0
Trun
k Line
B fo
r Mem
bran
e SW
ANFT
62A0
Trun
k Line
C fo
r Mem
bran
e SW
ANFT
67A0
Seria
l Com
mun
icatio
n Li
ne
ANFT
68A0
D Li
ght C
omm
unica
tion
Line
ANFT
69A0
Touc
hpad
SW
Trun
k Line
A fo
r
Safe
ty Sw
itch
for U
nder
Pum
p Co
ver
(AG
FS15
A0)
3
122
34 4
56
78
910
XA10
P
ANFT
76A0
Assis
tant
Sid
e
Green
22
44
ANFT
70A0
Powe
r Cab
le Se
ctionSa
fety
Switc
h fo
r Und
er P
ump
Cove
r
Brow
nRe
d
Brow
nRe
d
Chai
r Dow
n Pr
ohib
ition
Chai
r Ope
ratio
n Pr
ohib
ition
MotorUpDown
RecliningRaise
Up/Down Slow SlideBackrest Slow SlideLock Cancel
RedOrangeYellowGreenBluePurpleGray
Black
RedOrangeYellowGreenBluePurpleGray
Pink
WhiteBlack
White/Red
Light Blue
AR
UpDown
RecliningRaise
P1P2LP
COM
5VLock CancelSafetySafety LED.COM
BrownRed
Seria
l Tra
nsm
issio
n
Seria
l Rec
eptio
n
Seria
l Tra
nsm
issio
n
Seria
l Rec
eptio
n
RedBrown
RedBrown
OrangeYellowGreenBluePurpleGray
Black
Touc
hpad
SW
Trun
k Line
B fo
r
AR
UpDown
RecliningRaise
P1P2LP
COM
RedBrown
OrangeYellowGreenBluePurpleGrayBlack
RedBrown
OrangeYellowGreenBluePurpleGray
Black
AR
UpDown
RecliningRaise
P1P2LP
COM
Touc
hpad
SW
Trun
k Line
C fo
r
BrownRedOrangeYellowGreenBluePurpleGrayWhiteBlackPinkLight BlueWhite/Red
BrownRedOrangeYellowGreenBluePurpleGrayWhiteBlackPinkLight BlueWhite/Red
BrownRedOrangeYellowGreenBluePurpleGrayWhiteBlackPinkLight BlueWhite/Red
AR
UpDown
RecliningRaise
P1P2LP
5V
Lock CancelSafety
Safety LED.
COM
AR
UpDown
RecliningRaise
P1P2LP
5V
Lock CancelSafety
Safety LED.
COM
Arm
rest
Mem
bran
e SW
- R
Yello
wYe
llow
Yello
w
Yello
wW
hite
Red
Yello
wYe
llow
Gra
y
Gra
y
Trun
k Line
A fo
r Mem
bran
e SW
BlueBlue
Light Blue
Blue
WhiteWhite
BlackBlack
White
Blac
kBl
ack
Whit
e
Whit
eYe
llow
Whit
eYe
llow
Whit
eYe
llow
Trun
k Line
A fo
r Sole
noid
Valve
MotorUp
Down
RecliningRaise
COM Com
Up/Down Slow Slide
Backrest Slow Slide
COM
COM
Lock Cancel
SV8
SV7
3 2
VL4P4 1
Yello
wW
hite
Yello
wW
hite
Gre
enBl
ue
Yello
wO
rang
e
Up/D
own
Slow
Slid
e
Back
rest
Slow
Slid
e
Back
rest
Slow
Up/D
own
Slow
1 2
XA2P
Ther
mist
or
NTC
Ther
mist
or
Red
Brow
nBl
ack
Blac
kTh
erm
istor
for S
olen
oid
Valve
sCh
air u
pper
fram
e
Earth
Lin
e Base
Whit
e
- 25 -
16-2. Dr.Table Section
12
1 2 3 4
1 2
HP
Hol
der S
W P
CB. F
ourt
h Li
ne
4 3 2 1
21G
ray
Purp
le
14142424
(2.3
)
(1)
CN36
B03B
-XA
SK-1
N-A
321
Tim
erSp
ray
F(Fu
nctio
n)ST
ORE
LEDM
AIN
(Gre
en)
LOCK
(Ora
nge)
Ligh
t Pac
k(G
reen
)
Spra
y A
ir(Bl
ue)
Operation Switch
-+SE
LECT
Ligh
t Pac
kD
enta
l Lig
ht
Chair Operation Switch
LPP2P1AR
Rais
eD
own
UP
Trun
k Li
ne fo
r Dis
play
AN
FT93
XX
NO
COM
Min
i Air
Switc
h(F/
C)
AN
FT97
XX
AN
FT95
XX
AN
FT96
XX
AN
FT83
XX
AN
FT80
XX
AN
FT79
XX
AN
FT87
XX
AN
FT86
A0
AN
FT82
XX
AN
FT85
XX
Tran
sfor
mer
Sec
tion
AN
FT92
XX
Trun
k Li
ne fo
r Den
tal L
ight
Pow
er S
ourc
e (J
BOX)
AN
FT81
XX
21
32
13
21
3
Pow
er C
able
(UL)
JBO
X
AN
FT84
XX
Seria
l Com
mun
icat
ion
Line
AN
FT78
XX
Trun
k Li
ne fo
r HP
Hol
der
AN
FT77
XX
AGFS
17XX
AGFS
20XX
Air
SW
Fuse
F 10
A
120V
14V 24V
Tran
sfor
mer
FK-
023
Junc
tion
Box
Sect
ion
AC IN
1 2211 221
21
1 2 3
12
12
34
21
21
34
56
71
2
87654321 4321
8 7 6 5 4 3 2 1 87654321
1 2 3 4 5 6 7 8 1 2 3 4 1 21 221 1 221
1 2 3 4
43211 2
CN31
IL-2
P-S3
EN2
(JA
E)
21
CN3
IL-3
P-S3
EN2
(JA
E)
To S
eria
l Com
mun
icat
ion
Line
(ASS
)Se
rial T
rans
mis
sion
(1.2
)
Seria
l Rec
eptio
n(3
.4)
CN29
236-
747(
Gre
en)
(WAG
O)
CN26
IL-3
P-S3
EN2
(JA
E)PE
RIO
END
O
CN16
IL-4
P-S3
EN2
(JA
E)
Wat
er
Doc
tor M
embr
ane
SW(A
GFS
18XX
)
12
34
56
78
910
12
344
665
Uni
t P.C
.B.
(AG
FS22
XX)
CN21
IL-4
P-S3
EN2
(JA
E)
POW
ER
CN2
IL-2
P-S3
EN2
(JA
E)CN4
IL-2
P-S3
EN2
(JA
E)
CN6
IL-2
P-S3
EN2
(JA
E)
CN7
IL-3
P-S3
EN2
(JA
E)
CN10
IL-2
P-S3
EN2
(JA
E)
CN12
IL-2
P-S3
EN2
(JA
E)
CN17
IL-2
P-S3
EN2
(JA
E)
Air
SW
CN24
IL-4
P-S3
EN2
(JA
E)
CN25
IL-4
P-S3
EN2
(JA
E)
LP1
LP2
LP3
LP4
CN27
236
-401
(Gra
y)W
AGO
12
34
56
78
910
12
344
665
CN14
IL-2
P-S3
EN2
(JA
E)
Air
Red
Blac
kRe
dBl
ack
CN30
IL-2
P-S3
EN2
(JA
E)
Dis
play
(AG
FS19
XX)
12
34
56
78
910
CN5
IL-1
0P-S
3EN
2(J
AE)
CN18
IL-2
P-S3
CN2
(JA
E)W
hite
Blac
k
HP1
SV
HP2
SV
HP3
SV
HP4
SV
CN8
IL-8
P-S3
EN2
(JA
E)
HP1HP2
HP4
12V
0V0VHP3
CN13
IL-8
P-S3
EN2
(JA
E)
CN1
IL-3
P-S3
EN2
(JA
E)
CN36
236
-401
(Gra
y)W
AGO
CN37
236
-401
(Gra
y)W
AGO
CN38
236
-401
(Gra
y)W
AGO
CN23
IL-4
P-S3
EN2
(JA
E)
CN11
IL-8
P-S3
EN2
(JA
E)
FLA
SH
CN28
IL-7
P-S3
EN2
(JA
E)
CN19
IL-2
P-S3
EN2
(JA
E)
CN9
IL-4
P-S3
EN2
(JA
E)
GN
DCN
22IL
-2P-
S3EN
2(J
AE)
HP4
HP3
HP2
HP1
CN32
IL-2
P-S3
EN2
(JA
E)CN
33IL
-2P-
S3EN
2(J
AE)
CN34
IL-2
P-S3
EN2
(JA
E)CN
35IL
-2P-
S3EN
2(J
AE)
CN20
IL-1
0P-S
3EN
2(J
AE)
CN15
IL-6
P-S3
EN2
(JA
E)
XA-1
3PXA
-6P
AN
FT98
XX
Trun
k Li
ne A
for D
r Mem
bran
e SW
AN
FT99
XX
HP3HP2HP1
HP4
---
+++
-+
8
Sole
noid
Val
ve fo
r Pilo
t Air
Sole
noid
Val
ve fo
r Pilo
tA
ND
T08X
X
-+
-+
25
Sole
noid
Val
ve fo
r Spr
ayA
ND
T07X
X
1 2
12
1 2 3 4
12
12
1 21 21 2H
P H
olde
r SW
PCB
.
L N
Blac
k
VL4P
VL2P
Pow
er S
ourc
e fo
r Den
tal L
ight
AGD
R39X
X
Brow
n
Red
XA2PXA
2P
Gre
enBl
ue
Ora
nge
Yello
w
Brow
nRe
d
Stan
dard
Spe
c.
Syrin
ge T
urbi
ne x
3
Brow
n
AN
FU04
XX
Mai
n A
ir SW
Sec
tion
AGFL
34XX
AN
FU05
XX
Eart
h (D
r Tab
le)
CN1
PS-L
A-1
4P
CN1
12
1314
Brow
nRe
dO
rang
eG
reen
Yello
w
Blue
Gra
yPu
rple
Whi
te
Dynamic Output 1Dynamic Output 2Dynamic Output 3Dynamic LED 1Dynamic LED 2Dynamic LED 3
Red
BlackWhiteGray
BrownRed
OrangeYellowGreen
Blue
PurpleBlue
GreenYellow
Orange
Brown
Trun
k lin
e B
for 2
4V.1
2V
Powe
r Sou
rce
Purple
Blue
PurpleBlue
Purple
Blue
Black
Red
Mai
n G
auge
Cla
mp
Red
Blue
Red
Blac
k
Purp
leBl
ue
Trun
k lin
e A
for 2
4V.1
2V
Powe
r Sou
rce
Fuse
6A
Fuse
2A
Trun
k lin
e (B
lue)
for F
use
Hold
er
Trun
k lin
e (R
ed) f
or F
use
Hold
er
Gre
en/Y
ello
w
Trun
k lin
e (B
lack
) for
Fus
e Ho
lder
Chai
r Pow
er S
uppl
y Se
ctio
n
Chai
r Pow
er S
uppl
y Bl
ack
Blac
k
Blac
k
Whi
te
Whi
te
Whi
teG
reen
Blac
k
Blac
k
Gra
y
Whi
teW
hite
Whi
te
Gre
en/Y
ello
w
Earth
Purp
le
Purp
leO
rang
e
Ora
nge
Red Blac
kBl
uePu
rple
J-Bo
x G
auge
Cla
mp
Sect
ion
Both
con
nect
ors
to b
e co
nnec
ted,
2P
& 3
P)
Red
Blac
kRe
dBl
ack
Red
Blac
kRe
dBl
ack
HP
Hol
der S
W P
CB.
HP
Hol
der S
W P
CB.
Seria
l Tra
nsm
issi
on
Seria
l Rec
eptio
n
Brow
nBr
own
Brow
nBr
own
Brow
n
BrownRed
OrangeYellowGreen
Blue
WhiteGray
Purple
0V5VVFD-RS
Low
erSp
ray
Wat
er(B
lue)
Trun
k Li
ne B
for D
r Mem
bran
e SW
VFD-R/WVFD-E
VFD-1
VFD-3VFD-2
VFD-0
AN
FU69
XXTr
unk
line
(Bla
ck) f
or F
use
Hold
er
HP2
HP1
HP3
Input AInput BInput CInput DInput EInput FInput GInput H
Display LED.Display LED.
XA3P
1 32
Ora
nge
Yello
w
To S
eria
l Com
mun
icat
ion
Line
(CH
)Co
nnec
t 2P
conn
ecto
r onl
y
With
PM
U
With
out P
MU
12
34
PurpleBlueBlackRed
To te
rmin
al o
n as
sist
ant s
ide
1A03
XDXX
Trun
k lin
e C
for 2
4V.1
2V
Powe
r Sou
rce
Conn
ect t
runk
line
C fo
r 24V
.12V
fr
om c
uspi
dor
With
PM
U
With
out P
MU
Conn
ect t
runk
line
A a
nd B
Trun
k lin
e(Pu
rple
) for
Dr P
CB.
Powe
r Sou
rce
Trun
k lin
e(Bl
ue) f
or D
r PCB
. Po
wer S
ourc
e
Rota
tion
Dire
ctio
nFo
rwor
d Ro
tatio
n(G
reen
)
Reve
rse
Rota
tion(
Ora
nge)
B1A
1A
2B3
A3
B6A
6B7
A7
A4
A5
B2B4
B5
- 26 -
16-3. PMU Section
21
21
2121
1 21 2211 2 211 2
321
4321
1 2 3654321
1 2 1 21 2 3
1 2 3 44321
12
21
1 2 3 4 5 6
43
21
1 2
1G01
6Q**
Gau
ge C
lam
p (C
uspi
dor)
Chai
r Con
trol P
CB.
(AG
FS13
**)
12
34
56
78
998
76
54
32
1
XA9P
1A03
YA**
1
CN1-
2(1-
1)IL
-10P
-S3E
N2(J
AE)
109
87
65
34
21
XA9P
(AG
FS16
**)
ANFT
69**
12
34
56
78
9
XA9P
1A03
Y9**
Touc
hpad
Swi
tch
1G01
64**
Earth
(3m
)
1A03
Y8**
1A03
Y0**
1A03
XX**
1A03
XW**
1A03
XV**1G
0163
**
CB S
witc
h Se
ctio
n1G
0163
**N.
O.
N.O
.CO
MCO
M
(Top
View
)
(Sid
e Vi
ew)
XA C
onne
ctor
43
21
IL C
onne
ctor
CN16
B02B
-XAS
K-1
Cent
ral V
acuu
m S
W2
1
(JAE
)IL
-2P-
S3EN
2CN
6-B
(Cha
ir O
pera
tion
Proh
ibitio
n)
LOCK
CN17
-BB0
2B-X
ASK-
1
CN17
-AB0
2B-X
ASK-
1
CN18
B05B
-XAS
K-1
54
32
1
XA2P
XA2P
XA6P
Norm
ally
#3 s
ide(
4800
bps)
(#1
side
2400
bps)
Tran
smiss
ion
Spee
d
CN14LED6
Red
(Ful
l cap
acity
of c
upfill
er)
LED5
Ora
nge(
CN3
- dat
a tra
nsm
issio
n)
LED4
Ora
nge(
CN4
- dat
a tra
nsm
issio
n)
LED2
Gre
en(C
upLE
D-De
tect
a c
ap)
LED1
Gre
en(P
ower
LED
)
(JAE
)IL
-2P-
S3EN
2CN
6-A
LOCK
CN10
IL-2
P-S3
EN2
(JAE
)CU
R-HO
LD
CN11
IL-2
P-S3
EN2
(JAE
)SI
G-C
UR
(JAE
)IL
-2P-
S3EN
2CN
12Ex
tra
CN4
(JAE
)IL
-2P-
S3EN
2
(JAE
)IL
-2P-
S3EN
2CN
3
TXD
(JAE
)IL
-4P-
S3EN
2CN
2
RXD
CN7
(JAE
)IL
-3P-
S3EN
2
(JAE
)IL
-3P-
S3EN
2CN
8
FULL
Sen
sor
CUP
Sens
or
(JAE
)IL
-6P-
S3EN
2CN
9
CUP
SW
CUP
SV
BOW
L SV
(WAG
O)
236-
747
CN12
1
Assis
tant
PCB
.(A
GDJ
73**
)
POW
ER
1A03
XZ**
1A03
Y1**
1A03
Y7**
Trun
k Li
ne fo
r 14V
Pow
er S
ouce
1A03
XY**
3
12
34
56
7
FLAS
H
CN19
B07B
-XAS
K-1
Notc
hed
for #
1 Pi
n sid
e
12
34
5 .
. .
12
34
CN20
Norm
ally
# 3
side
(#1
side
for w
ritin
g of
dat
a)
Data
inpu
tXA
3P
J Bo
x Se
ctio
n
12
34
56
78
IL-8
P-S3
EN2
CN5
(JAE
)
VL4P
VL4P
XA2P
XA2P
Cusp
idor
Sec
tion
Cupf
iller S
witc
hBo
wl R
inse
Swi
tch
XA4P
Gre
en/Y
ello
w
Blac
k do
t ind
icate
rs m
ale
pin
side
Cap
Plug
21
XA2P
1G01
7J**
1G01
7K**
XA2P
Opt
ion
32
1
WRI
TEO
UT1
23
2009
0717
BDS-
5000
-PMU
UpDown
ARP1P2LP
COM
RaiseReclining
BrownRed
GreemBluePurpleGrayBlack
OrangeYellow
BrownRed
GreemBluePurpleGrayBlack
OrangeYellow
BrownRed
GreemBluePurpleGrayBlack
OrangeYellow
Trun
k Li
ne A
for
Touc
hpad
SW
Trun
k Li
ne B
for
To
uchp
ad S
W (f
or P
MU)
Trun
k Li
ne C
for
Touc
hpad
SW
(for
PM
U)
Sole
noid
Val
ve fo
r Bow
l Rin
seVD
W21
-6G
-2-M
5
Sole
noid
Val
ve fo
r Cup
fille
rVD
W21
-6G
-2-M
5
Sole
noid
Val
ve fo
r Bow
l Rin
seV-
114-
6G-M
5-X7
0
Red
Blac
kR
edBl
ack
Brow
nR
edO
rang
eYe
llow
Red
Blac
k
Cup
fille
r Sol
enoi
d Va
lve
Sect
ion
Bow
l Rin
se S
olen
oid
Valv
e Se
ctio
n
Bowl
Rin
se S
olen
oid
Valve
Se
ctio
n
Red
Blac
k
Trun
k Li
ne fo
r Sol
enoi
d Va
lve
-+
-+
-+
[Rem
arks
]Co
nnec
tor S
ymbo
l X
A .
. .
XA C
onne
ctor
VL
. .
. VL
Con
nect
or
Brown
RedOrange
EXTCOM
ARLPP2P1
BOWLCUP
(Cha
ir O
pera
tion
Proh
ibitio
n)
TXDSCLKRXDBUSYRESETCNVSSGND
PurpleBlue
18V PowerSignal(Red)
Signal(Green)Signal(Blue)
Signal(Orange)
TXD
Safe
ty S
W fo
r Dr
.Tab
le A
rm
Safe
ty S
W fo
r Dr
.Tab
le A
rm
TXD
Trun
k Li
ne(A
ss) A
for
Seria
l Com
mun
icatio
n Li
ne
Trun
k Li
ne(A
ss) B
for
Seria
l Com
mun
icatio
n Li
neBr
own
Red
Ora
nge
Yello
wBr
own
Red
Brow
nR
edTo
Cha
ir Se
rial
Com
mun
icat
ion
Line
(CH
)
To D
r.Tab
le S
eria
l C
omm
unic
atio
n Li
ne(U
nit)
Trun
k Li
ne C
for C
B Sw
itch
Ora
nge
Blue
Brow
nPu
rple
Red
Ora
nge
Blue
Brow
nPu
rple
Red
Red Red
Blac
k
BrownOrange
RedRed
Trun
k Li
ne B
for C
B Sw
itch
Trun
k Li
ne A
for C
B Sw
itch
Trun
k Li
ne C
for 2
4V/1
4V P
ower
So
uce
BrownRed
BrownRed
CB S
witc
h Se
ctio
n
Red
Blac
kBl
uePu
rple
Conn
ect t
o Tr
unk
Line
B fo
r 24
V/14
V Po
wer S
ouce
Conn
ect t
o Tr
unk
Line
A fo
r 24
V/14
V Po
wer S
ouce
(Sid
e Vi
ew)
Pin
Num
ber A
rrang
emen
tLE
D3 O
rang
e(CN
2 - d
ata
trans
miss
ion)
5 .
. .
5 .
. .
- 27 -
17. Location of the Product Labels
17-3. Product label (SERIAL No.) is
located side of the assistant
swing arm.
17-2. Product label (SERIAL No.) is
located side of the doctor swing arm.
17-4. Product label (SERIAL No.) is
located side of the PMU swing arm.
ET
L L
IST
ED
US
CONF
ORM
S TO
UL S
TD 73
CERT
IFIE
D TO
CAN/
CSA
STD
C22.
2NO
. 68
2007
Model QUOLIS5000 UNITSerial No.Rated VoltageRated CurrentClassification
ManufacturedProduct of Japan
ZZ535521
AW********* ****1V ~ 60Hz
1A
GS1-128
(**)**************(**)*********
2-1-1.Higashishinsaibashi,Chuo-ku,Osaka,Japan
101 BELMONT DRIVE, SOMERSET, NJ 08873BELMONT EQUIPMENT, A Division of Takara Belmont USA Inc.
10 2007** ****
Dental Delivery Unit
2007
ModelQUOLIS5000 UNIT
Serial No.
Rated Voltage
Rated Current
Classification
Manufactured
Product of Japan
ZZ535521
AW*********
****120V ~ 60Hz
1 A
GS1-128
(**)**************(**)*********
2-1-1.Higashishinsaibashi,Chuo-ku,Osaka,Japan
Takara Belmont
101 BELMONT DRIVE, SOMERSET, NJ 08873
BELMONT EQUIPMENT, A Division of Takara Belmont USA Inc.
10 2007
** ****
RECOGNIZED COMPONENT
PART1: GENERALREQUIREMENTS
MEDICAL ELECTRICALEQUIPMENT
CONFORMS TO UL STD 60601-13058278
Takara Belmont Corp.
17-1. Product label & ETL label are
located under the doctor table.
- 28 -
18. Floor Template
18. Floor Template
8
5-1/
2
3/8
1-1/
2
5-3/
4
5-3/
82
1
2
TRANSFORMER
4-3/8
5-3/8
1-3/8
4
3-3/4
GRAVITY DRAIN(1-1/2 NORMAL PIPE)FOR PMU
GRAVITY DRAIN(1-1/2 NORMAL PIPE)
FINISHED FLOOR
TELECOMMUNICATIONS(1-1/2 NORMAL PIPE)
TELECOMMUNICATIONS(1-1/2 NORMAL PIPE)
ELECTRICAL CONDUITFOR QUAD BOX(1/2 O.D.)
ELECTRICAL CONDUITFOR QUAD BOX(1/2 O.D.)
AIR(1/2’ THREADED PIPE)
AIR(1/2’ THREADED PIPE)
WATER (For option)(1/2 THREADED PIPE)
WATER(1/2 THREADED PIPE)
CENTRAL VACUUM(5/8 O.D. TUBE)
CENTRAL VACUUM(5/8 O.D. TUBE)
-28-
- 29 -
NOTE
BELMONT EQUIPMENT, Division of Takara Belmont USA, Inc.101 Belmont Drive Somerset, New Jersey 08873 U.S.A. TEL.:(732) 469-5000 / (800) 223-1192 Fax.:(732)526-6322 / (800) 280-7504
TAKARA CO, CANADA LTD.2076 S. Sheridan Way, Mississauga, Ont., L5J2M4, Can. TEL.:(905) 822-2755 Fax.:(905)822-6203
R
AFFY69B0