-
1
2
Contents
Assembly Features
Have a better look.™
Q-Optics / Quality Aspirators1419 Godwin LaneDuncanville, Texas 75116 USA
972-298-2669 Local800-858-2121 US & Canada only972-298-6592 Fax
© 2018 Q-Optics. All rights reserved. Product specifications are subject to change at any time without prior notice. www.q-optics.com
UI-317-10009-08 ECN # 1980
Before you begin, verify light system kit contents:
Welcome to Q-Optics Radiant™ Light System
HeadlightHeadlight style may vary
Anti-Curing Filter Shirt Clip Spiral Wrap
System Features The Q-Optics Radiant™ Light System is an adjustable light system which features an ergonomic and easy to understand control panel integrated with the battery pack. Note the location and function of the interface and controls shown below.
System AssemblyAssembling the Radiant Light System is quick and easy. For use, simply insert the headlight interface into the top of the battery pack.
WarrantyLimited Manufacturers Warranty
Quality Aspirators guarantees material, construction and design to be free of defi ciencies from the time of fi rst purchase.
The warranty lasts 12 months from the time of purchase by the original purchaser. In the event of change of ownership from the original purchaser the warranty will last for the remainder of the 12 month period.
Defective units will be repaired or replaced by Quality Aspirators or its authorized representative. Quality Aspirators has the sole and fi nal decision in determining if a unit is defective and whether or not the unit will be repaired or replaced with similar equipment.
Units that are repaired or their replacement units do not receive any extended warranty. The fi nal length of warranty even in the event of repair or replacement is 12 months from the time of original purchase.
Batteries are an expendable part and are not considered defective by simply exhibiting diminished capacity. Batteries are under warranty for a period of 12 months from the time of original purchase.
Mistreatment, misuse, or tampering with the unit voids all warranty rights. Manual instructions and warnings must be observed at all times.
For initiation of a warranty claim in the USA please contact:
Quality Aspirators1419 Godwin Ln
Duncanville, TX 75116
P 972-298-2669
support@q-optics [email protected]
Outside the USA – please contact your local distributor.
No changes may be made to this warranty without being fi rst written, printed, and published by Quality Aspirators Inc.
Technical DataWeight of Battery Pack6.5 ounces
Weight of HeadlightSee Data Sheet
Battery TypeLi-Ion battery, 3.6 V / 4500 mAh
Battery Charge TimeUp to 4 hours
Battery LifeLow intensity - ≈ 40+ hoursMedium intensity - ≈ 15.5 - 16 hoursHigh intensity - ≈ 7.5 - 8 hours
Light IntensitySee Data Sheet
Operation ModeContinuous
Operation and Storage Temperature32º to 95º F (0 to 35 C)
For charging the battery pack, simply plug the power supply cord interface into the charger interface on the bottom of the unit as shown.
Headlight
Belt ClipHeadlight
connection interface
Power supply connection interface
Intensity up
On/Off
Battery Status
Intensity down
PowerSupply
Radiant™ LIGHT SYSTEM
Battery Pack model #RADBL25
Power Supply model #FY0503000
5V - 2.5A DC power supply
-
1
2
Contents
Assembly Features
Have a better look.™
Q-Optics / Quality Aspirators1419 Godwin LaneDuncanville, Texas 75116 USA
972-298-2669 Local800-858-2121 US & Canada only972-298-6592 Fax
© 2018 Q-Optics. All rights reserved. Product specifications are subject to change at any time without prior notice.www.q-optics.com
UI-317-10009-08 ECN # 1980
Before you begin, verify light system kit contents:
Welcome to Q-Optics Radiant™ Light System
HeadlightHeadlight style may vary
Anti-Curing FilterShirt ClipSpiral Wrap
System Features The Q-Optics Radiant™ Light System is an adjustable light system which features an ergonomic and easy to understand control panel integrated with the battery pack. Note the location and function of the interface and controls shown below.
System AssemblyAssembling the Radiant Light System is quick and easy. For use, simply insert the headlight interface into the top of the battery pack.
WarrantyLimited Manufacturers Warranty
Quality Aspirators guarantees material, construction and design to be free of defi ciencies from the time of fi rst purchase.
The warranty lasts 12 months from the time of purchase by the original purchaser. In the event of change of ownership from the original purchaser the warranty will last for the remainder of the 12 month period.
Defective units will be repaired or replaced by Quality Aspirators or its authorized representative. Quality Aspirators has the sole and fi nal decision in determining if a unit is defective and whether or not the unit will be repaired or replaced with similar equipment.
Units that are repaired or their replacement units do not receive any extended warranty. The fi nal length of warranty even in the event of repair or replacement is 12 months from the time of original purchase.
Batteries are an expendable part and are not considered defective by simply exhibiting diminished capacity. Batteries are under warranty for a period of 12 months from the time of original purchase.
Mistreatment, misuse, or tampering with the unit voids all warranty rights. Manual instructions and warnings must be observed at all times.
For initiation of a warranty claim in the USA please contact:
Quality Aspirators1419 Godwin Ln
Duncanville, TX 75116
P 972-298-2669
support@q-optics [email protected]
Outside the USA – please contact your local distributor.
No changes may be made to this warranty without being fi rst written, printed, and published by Quality Aspirators Inc.
Technical DataWeight of Battery Pack 6.5 ounces
Weight of Headlight See Data Sheet
Battery Type Li-Ion battery, 3.6 V / 4500 mAh
Battery Charge Time Up to 4 hours
Battery LifeLow intensity - ≈ 40+ hoursMedium intensity - ≈ 15.5 - 16 hoursHigh intensity - ≈ 7.5 - 8 hours
Light Intensity See Data Sheet
Operation Mode Continuous
Operation and Storage Temperature 32º to 95º F (0 to 35 C)
For charging the battery pack, simply plug the power supply cord interface into the charger interface on the bottom of the unit as shown.
Headlight
Belt ClipHeadlight
connection interface
Power supply connection interface
Intensity up
On/Off
Battery Status
Intensity down
PowerSupply
Radiant™
LIGHT SYSTEM
Battery Pack model #RADBL25
Power Supply model #FY0503000
5V - 2.5A DC power supply
-
1
2
Contents
Assembly Features
Have a better look.™
Q-Optics / Quality Aspirators1419 Godwin LaneDuncanville, Texas 75116 USA
972-298-2669 Local800-858-2121 US & Canada only972-298-6592 Fax
© 2018 Q-Optics. All rights reserved. Product specifications are subject to change at any time without prior notice.www.q-optics.com
UI-317-10009-08 ECN # 1980
Before you begin, verify light system kit contents:
Welcome to Q-Optics Radiant™ Light System
HeadlightHeadlight style may vary
Anti-Curing FilterShirt ClipSpiral Wrap
System Features The Q-Optics Radiant™ Light System is an adjustable light system which features an ergonomic and easy to understand control panel integrated with the battery pack. Note the location and function of the interface and controls shown below.
System AssemblyAssembling the Radiant Light System is quick and easy. For use, simply insert the headlight interface into the top of the battery pack.
WarrantyLimited Manufacturers Warranty
Quality Aspirators guarantees material, construction and design to be free of defi ciencies from the time of fi rst purchase.
The warranty lasts 12 months from the time of purchase by the original purchaser. In the event of change of ownership from the original purchaser the warranty will last for the remainder of the 12 month period.
Defective units will be repaired or replaced by Quality Aspirators or its authorized representative. Quality Aspirators has the sole and fi nal decision in determining if a unit is defective and whether or not the unit will be repaired or replaced with similar equipment.
Units that are repaired or their replacement units do not receive any extended warranty. The fi nal length of warranty even in the event of repair or replacement is 12 months from the time of original purchase.
Batteries are an expendable part and are not considered defective by simply exhibiting diminished capacity. Batteries are under warranty for a period of 12 months from the time of original purchase.
Mistreatment, misuse, or tampering with the unit voids all warranty rights. Manual instructions and warnings must be observed at all times.
For initiation of a warranty claim in the USA please contact:
Quality Aspirators1419 Godwin Ln
Duncanville, TX 75116
P 972-298-2669
support@q-optics [email protected]
Outside the USA – please contact your local distributor.
No changes may be made to this warranty without being fi rst written, printed, and published by Quality Aspirators Inc.
Technical DataWeight of Battery Pack 6.5 ounces
Weight of Headlight See Data Sheet
Battery Type Li-Ion battery, 3.6 V / 4500 mAh
Battery Charge Time Up to 4 hours
Battery LifeLow intensity - ≈ 40+ hoursMedium intensity - ≈ 15.5 - 16 hoursHigh intensity - ≈ 7.5 - 8 hours
Light Intensity See Data Sheet
Operation Mode Continuous
Operation and Storage Temperature 32º to 95º F (0 to 35 C)
For charging the battery pack, simply plug the power supply cord interface into the charger interface on the bottom of the unit as shown.
Headlight
Belt ClipHeadlight
connection interface
Power supply connection interface
Intensity up
On/Off
Battery Status
Intensity down
PowerSupply
Radiant™
LIGHT SYSTEM
Battery Pack model #RADBL25
Power Supply model #FY0503000
5V - 2.5A DC power supply
-
3
4
5
6
Using the Battery Pack
Using the Headlight
Using the Power Supply
Cleaning and Care
Battery Pack OperationOperating the system is simple and intuitive by way of visual indication, which occur upon pressing a control button. Pressing the increase/decrease intensity buttons will be accompanied by a visual LED display of the current light level (1-10).
SuggestionsLonger battery life – Decrease intensity to increase battery life.
Anti-curing – Use included anti-curing fi lter or decrease intensity to prevent fast curing of composite material.
Increase intensity button:10 positions, LED display indicates current light level. Will also turn on headlight if it is currently off *.
On/Off button:Turns the headlight on and indicates current battery level using LED display, or turns the headlight off *.
Decrease intensity button:10 positions, LED display indicates current light level. Will also turn on headlight if it is currently off *.
Battery Status button:LED display indicates current battery level.Battery LED indicates battery status.GREEN - Battery can run headlight.RED - Battery needs charging - headlight may not turn on.
Battery LED
LED display
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
Warnings
• Do not disassemble battery pack
• Do not dispose of battery pack in fi re
• Do not heat battery pack above 60o Celsius (140o Fahrenheit)
Warning
• Headlight heats up during useTouch with Caution
HeadlightThe Q-Optics Radiant™ Light System Headlight mounts easily via the “Quick Connect Mount” enabling use with the Q-Optics Headband, most brands custom TTL style loupes, most brands fl ip style loupes, eyeglasses, and safety glasses.
Cleaning and CareThe Q-Optics Radiant™ headlight is a fi ne optical instrument and should be handled with care.
1. Do not submerge headlight into water or any type of sterilization fl uid. The headlight is not water proof.
2. Basic cleaning may be done with a clean dry micro fi ber cloth or the lens can be sprayed lightly with Q-Optics Optical Lens Cleaner. Use a light pressured circular motion to clean or dry the headlight lens.
3. It is OK to disinfect headlight using alcohol, Lysol® spray, Cavi-Wipes or other surface disinfectant.
4. Do not use solvents or cleaning solutions other than those listed above on the headlight or battery pack.
Disposal Instructions
1. Do not throw headlight, battery pack or charger in the trash.
2. Contact your local authorities for disposal or return to Q-Optics for free disposal.
Attach mounting clip (if necessary) using instructions included with clip. Headbands and some loupes come with clip already mounted.
Remove name plate (if necessary) by pressing upward from the bottom and off to reveal the mounting screws as shown above.
Mounting clip styles will vary.
Power supply styles and indicator light position will vary.
Attach the headlight by sliding the quick disconnect onto the mounting screws as shown.
Install spiral wrap using instructions included with clips. For headbands use the clips on the side of the band. Attach the headlight cable to the side clips.
1. Plug power supply into bottom of the battery pack.
2. Plug power supply into electrical outlet.
3. Battery LED will be RED to indicate battery is charging. LED display will pulse to indicate current level of battery. When Battery LED is no longer RED battery is fully charged.
GREEN Light – Indicates power supply is on.Does NOT indicate charge status.
Install anti-curing fi lter using the steps below.
Connect headlight cable to battery pack and enjoy your Q-Optics Radiant™ Light System.
1. Align fi lter with front of headlight as shown.
Attach shirt clip to headlight cable. Connect clip to the desired position on your clothing to keep cable out of your work area.
Snap clip onto headlight cable
Do not spray cleaning or disinfecting solutions into open electrical areas on the battery pack. Damage may occur.
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
Using the Power Supply MODEL# FY0503000READ THESE INSTRUCTIONS BEFORE USING POWER SUPPLY
Power SupplyPower Supply
Q-Optics • 1419 Godwin Ln • Duncanville, TX 75116 USA
Install spiral wrap using instructions included
Low Battery Warning:If the headlight is on it will toggle from bright to dim for about 1 second four or fi ve times to indicate a critical battery, charge battery. The Battery LED will fl ash red every four seconds to indicate a critical battery, charge battery.
* Headlight will only turn on if fully plugged in.
Install anti-curing fi lter using the steps below.
1. Align fi lter with front of headlight as shown.
2. Snap fi lter onto front of
headlight.
-
3
4
5
6
Using the Battery Pack
Using the Headlight
Using the Power Supply
Cleaning and Care
Battery Pack OperationOperating the system is simple and intuitive by way of visual indication, which occur upon pressing a control button. Pressing the increase/decrease intensity buttons will be accompanied by a visual LED display of the current light level (1-10).
SuggestionsLonger battery life – Decrease intensity to increase battery life.
Anti-curing – Use included anti-curing fi lter or decrease intensity to prevent fast curing of composite material.
Increase intensity button:10 positions, LED display indicates current light level. Will also turn on headlight if it is currently off *.
On/Off button:Turns the headlight on and indicates current battery level using LED display, or turns the headlight off *.
Decrease intensity button:10 positions, LED display indicates current light level. Will also turn on headlight if it is currently off *.
Battery Status button:LED display indicates current battery level.Battery LED indicates battery status.GREEN - Battery can run headlight.RED - Battery needs charging - headlight may not turn on.
Battery LED
LED display
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
Warnings
• Do not disassemble battery pack
• Do not dispose of battery pack in fi re
• Do not heat battery pack above 60o Celsius (140o Fahrenheit)
Warning
• Headlight heats up during useTouch with Caution
HeadlightThe Q-Optics Radiant™ Light System Headlight mounts easily via the “Quick Connect Mount” enabling use with the Q-Optics Headband, most brands custom TTL style loupes, most brands fl ip style loupes, eyeglasses, and safety glasses.
Cleaning and CareThe Q-Optics Radiant™ headlight is a fi ne optical instrument and should be handled with care.
1. Do not submerge headlight into water or any type of sterilization fl uid. The headlight is not water proof.
2. Basic cleaning may be done with a clean dry micro fi ber cloth or the lens can be sprayed lightly with Q-Optics Optical Lens Cleaner. Use a light pressured circular motion to clean or dry the headlight lens.
3. It is OK to disinfect headlight using alcohol, Lysol® spray, Cavi-Wipes or other surface disinfectant.
4. Do not use solvents or cleaning solutions other than those listed above on the headlight or battery pack.
Disposal Instructions
1. Do not throw headlight, battery pack or charger in the trash.
2. Contact your local authorities for disposal or return to Q-Optics for free disposal.
Attach mounting clip (if necessary) using instructions included with clip. Headbands and some loupes come with clip already mounted.
Remove name plate (if necessary) by pressing upward from the bottom and off to reveal the mounting screws as shown above.
Mounting clip styles will vary.
Power supply styles and indicator light position will vary.
Attach the headlight by sliding the quick disconnect onto the mounting screws as shown.
Install spiral wrap using instructions included with clips. For headbands use the clips on the side of the band. Attach the headlight cable to the side clips.
1. Plug power supply into bottom of the battery pack.
2. Plug power supply into electrical outlet.
3. Battery LED will be RED to indicate battery is charging. LED display will pulse to indicate current level of battery. When Battery LED is no longer RED battery is fully charged.
GREEN Light – Indicates power supply is on.Does NOT indicate charge status.
Install anti-curing fi lter using the steps below.
Connect headlight cable to battery pack and enjoy your Q-Optics Radiant™ Light System.
1. Align fi lter with front of headlight as shown.
Attach shirt clip to headlight cable. Connect clip to the desired position on your clothing to keep cable out of your work area.
Snap clip onto headlight cable
Do not spray cleaning or disinfecting solutions into open electrical areas on the battery pack. Damage may occur.
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
Using the Power Supply MODEL# FY0503000READ THESE INSTRUCTIONS BEFORE USING POWER SUPPLY
Power SupplyPower Supply
Q-Optics • 1419 Godwin Ln • Duncanville, TX 75116 USA
Install spiral wrap using instructions included
Low Battery Warning:If the headlight is on it will toggle from bright to dim for about 1 second four or fi ve times to indicate a critical battery, charge battery. The Battery LED will fl ash red every four seconds to indicate a critical battery, charge battery.
* Headlight will only turn on if fully plugged in.
Install anti-curing fi lter using the steps below.
1. Align fi lter with front of headlight as shown.
2. Snap fi lter onto front of
headlight.
-
3
4
5
6
Using the Battery Pack
Using the Headlight
Using the Power Supply
Cleaning and Care
Battery Pack OperationOperating the system is simple and intuitive by way of visual indication, which occur upon pressing a control button. Pressing the increase/decrease intensity buttons will be accompanied by a visual LED display of the current light level (1-10).
SuggestionsLonger battery life – Decrease intensity to increase battery life.
Anti-curing – Use included anti-curing fi lter or decrease intensity to prevent fast curing of composite material.
Increase intensity button:10 positions, LED display indicates current light level. Will also turn on headlight if it is currently off *.
On/Off button:Turns the headlight on and indicates current battery level using LED display, or turns the headlight off *.
Decrease intensity button:10 positions, LED display indicates current light level. Will also turn on headlight if it is currently off *.
Battery Status button:LED display indicates current battery level.Battery LED indicates battery status.GREEN - Battery can run headlight.RED - Battery needs charging - headlight may not turn on.
Battery LED
LED display
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
Warnings
• Do not disassemble battery pack
• Do not dispose of battery pack in fi re
• Do not heat battery pack above 60o Celsius (140o Fahrenheit)
Warning
• Headlight heats up during useTouch with Caution
HeadlightThe Q-Optics Radiant™ Light System Headlight mounts easily via the “Quick Connect Mount” enabling use with the Q-Optics Headband, most brands custom TTL style loupes, most brands fl ip style loupes, eyeglasses, and safety glasses.
Cleaning and CareThe Q-Optics Radiant™ headlight is a fi ne optical instrument and should be handled with care.
1. Do not submerge headlight into water or any type of sterilization fl uid. The headlight is not water proof.
2. Basic cleaning may be done with a clean dry micro fi ber cloth or the lens can be sprayed lightly with Q-Optics Optical Lens Cleaner. Use a light pressured circular motion to clean or dry the headlight lens.
3. It is OK to disinfect headlight using alcohol, Lysol® spray, Cavi-Wipes or other surface disinfectant.
4. Do not use solvents or cleaning solutions other than those listed above on the headlight or battery pack.
Disposal Instructions
1. Do not throw headlight, battery pack or charger in the trash.
2. Contact your local authorities for disposal or return to Q-Optics for free disposal.
Attach mounting clip (if necessary) using instructions included with clip. Headbands and some loupes come with clip already mounted.
Remove name plate (if necessary) by pressing upward from the bottom and off to reveal the mounting screws as shown above.
Mounting clip styles will vary.
Power supply styles and indicator light position will vary.
Attach the headlight by sliding the quick disconnect onto the mounting screws as shown.
Install spiral wrap using instructions included with clips. For headbands use the clips on the side of the band. Attach the headlight cable to the side clips.
1. Plug power supply into bottom of the battery pack.
2. Plug power supply into electrical outlet.
3. Battery LED will be RED to indicate battery is charging. LED display will pulse to indicate current level of battery. When Battery LED is no longer RED battery is fully charged.
GREEN Light – Indicates power supply is on.Does NOT indicate charge status.
Install anti-curing fi lter using the steps below.
Connect headlight cable to battery pack and enjoy your Q-Optics Radiant™ Light System.
1. Align fi lter with front of headlight as shown.
Attach shirt clip to headlight cable. Connect clip to the desired position on your clothing to keep cable out of your work area.
Snap clip onto headlight cable
Do not spray cleaning or disinfecting solutions into open electrical areas on the battery pack. Damage may occur.
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
Using the Power Supply MODEL# FY0503000READ THESE INSTRUCTIONS BEFORE USING POWER SUPPLY
Power SupplyPower Supply
Q-Optics • 1419 Godwin Ln • Duncanville, TX 75116 USA
Install spiral wrap using instructions included
Low Battery Warning:If the headlight is on it will toggle from bright to dim for about 1 second four or fi ve times to indicate a critical battery, charge battery. The Battery LED will fl ash red every four seconds to indicate a critical battery, charge battery.
* Headlight will only turn on if fully plugged in.
Install anti-curing fi lter using the steps below.
1. Align fi lter with front of headlight as shown.
2. Snap fi lter onto front of
headlight.
-
3
4
5
6
Using the Battery Pack
Using the Headlight
Using the Power Supply
Cleaning and Care
Battery Pack OperationOperating the system is simple and intuitive by way of visual indication, which occur upon pressing a control button. Pressing the increase/decrease intensity buttons will be accompanied by a visual LED display of the current light level (1-10).
SuggestionsLonger battery life – Decrease intensity to increase battery life.
Anti-curing – Use included anti-curing fi lter or decrease intensity to prevent fast curing of composite material.
Increase intensity button:10 positions, LED display indicates current light level. Will also turn on headlight if it is currently off *.
On/Off button:Turns the headlight on and indicates current battery level using LED display, or turns the headlight off *.
Decrease intensity button:10 positions, LED display indicates current light level. Will also turn on headlight if it is currently off *.
Battery Status button:LED display indicates current battery level.Battery LED indicates battery status.GREEN - Battery can run headlight.RED - Battery needs charging - headlight may not turn on.
Battery LED
LED display
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
Warnings
• Do not disassemble battery pack
• Do not dispose of battery pack in fi re
• Do not heat battery pack above 60o Celsius (140o Fahrenheit)
Warning
• Headlight heats up during useTouch with Caution
HeadlightThe Q-Optics Radiant™ Light System Headlight mounts easily via the “Quick Connect Mount” enabling use with the Q-Optics Headband, most brands custom TTL style loupes, most brands fl ip style loupes, eyeglasses, and safety glasses.
Cleaning and CareThe Q-Optics Radiant™ headlight is a fi ne optical instrument and should be handled with care.
1. Do not submerge headlight into water or any type of sterilization fl uid. The headlight is not water proof.
2. Basic cleaning may be done with a clean dry micro fi ber cloth or the lens can be sprayed lightly with Q-Optics Optical Lens Cleaner. Use a light pressured circular motion to clean or dry the headlight lens.
3. It is OK to disinfect headlight using alcohol, Lysol® spray, Cavi-Wipes or other surface disinfectant.
4. Do not use solvents or cleaning solutions other than those listed above on the headlight or battery pack.
Disposal Instructions
1. Do not throw headlight, battery pack or charger in the trash.
2. Contact your local authorities for disposal or return to Q-Optics for free disposal.
Attach mounting clip (if necessary) using instructions included with clip. Headbands and some loupes come with clip already mounted.
Remove name plate (if necessary) by pressing upward from the bottom and off to reveal the mounting screws as shown above.
Mounting clip styles will vary.
Power supply styles and indicator light position will vary.
Attach the headlight by sliding the quick disconnect onto the mounting screws as shown.
Install spiral wrap using instructions included with clips. For headbands use the clips on the side of the band. Attach the headlight cable to the side clips.
1. Plug power supply into bottom of the battery pack.
2. Plug power supply into electrical outlet.
3. Battery LED will be RED to indicate battery is charging. LED display will pulse to indicate current level of battery. When Battery LED is no longer RED battery is fully charged.
GREEN Light – Indicates power supply is on.Does NOT indicate charge status.
Install anti-curing fi lter using the steps below.
Connect headlight cable to battery pack and enjoy your Q-Optics Radiant™ Light System.
1. Align fi lter with front of headlight as shown.
Attach shirt clip to headlight cable. Connect clip to the desired position on your clothing to keep cable out of your work area.
Snap clip onto headlight cable
Do not spray cleaning or disinfecting solutions into open electrical areas on the battery pack. Damage may occur.
1
Become familiar with the safety symbols presented in thissection. These symbols will alert you to safety hazardsand conditions that may result in personal injury, death, orproperty and equipment damage.
WARNING: Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of electrical shock. Failure toobserve this warning may result in personalinjury, death, or equipment damage.
WARNING: Disconnect equipment from linevoltage. Failure to observe this warning mayresult in personal injury, death, or equipmentdamage.
WARNING: Risk of explosion or fire. Fire, openflames, and smoking prohibited.
WARNING: Wear protective clothing, safetygoggles, and approved respiratory protection.Failure to observe may result in serious injury.
WARNING: Hot! Risk of burns. Wearheat-protective clothing, safety goggles with sideshields and/or heat-protective gloves dependingon the symbol shown.
WARNING: System or material pressurized.Relieve pressure. Failure to observe thiswarning may result in serious injury or death.
1. Safety Symbols
RED
RED
Green
Voltage {V}
Charge CurrentCurrent {A}
Chargetermination
Current80-95%
Fast chargeIndication:
Final charge
Charge voltage
Charging Diagram
Charge completed
GREENREDRED
100% Capacity
Using the Power Supply MODEL# FY0503000READ THESE INSTRUCTIONS BEFORE USING POWER SUPPLY
Power SupplyPower Supply
Q-Optics • 1419 Godwin Ln • Duncanville, TX 75116 USA
Install spiral wrap using instructions included
Low Battery Warning:If the headlight is on it will toggle from bright to dim for about 1 second four or fi ve times to indicate a critical battery, charge battery. The Battery LED will fl ash red every four seconds to indicate a critical battery, charge battery.
* Headlight will only turn on if fully plugged in.
Install anti-curing fi lter using the steps below.
1. Align fi lter with front of headlight as shown.
2. Snap fi lter onto front of
headlight.
-
1
2
Contents
Assembly Features
Have a better look.™
Q-Optics / Quality Aspirators1419 Godwin LaneDuncanville, Texas 75116 USA
972-298-2669 Local800-858-2121 US & Canada only972-298-6592 Fax
© 2018 Q-Optics. All rights reserved. Product specifications are subject to change at any time without prior notice.www.q-optics.com
UI-317-10009-08 ECN # 1980
Before you begin, verify light system kit contents:
Welcome to Q-Optics Radiant™ Light System
HeadlightHeadlight style may vary
Anti-Curing FilterShirt ClipSpiral Wrap
System Features The Q-Optics Radiant™ Light System is an adjustable light system which features an ergonomic and easy to understand control panel integrated with the battery pack. Note the location and function of the interface and controls shown below.
System AssemblyAssembling the Radiant Light System is quick and easy. For use, simply insert the headlight interface into the top of the battery pack.
WarrantyLimited Manufacturers Warranty
Quality Aspirators guarantees material, construction and design to be free of defi ciencies from the time of fi rst purchase.
The warranty lasts 12 months from the time of purchase by the original purchaser. In the event of change of ownership from the original purchaser the warranty will last for the remainder of the 12 month period.
Defective units will be repaired or replaced by Quality Aspirators or its authorized representative. Quality Aspirators has the sole and fi nal decision in determining if a unit is defective and whether or not the unit will be repaired or replaced with similar equipment.
Units that are repaired or their replacement units do not receive any extended warranty. The fi nal length of warranty even in the event of repair or replacement is 12 months from the time of original purchase.
Batteries are an expendable part and are not considered defective by simply exhibiting diminished capacity. Batteries are under warranty for a period of 12 months from the time of original purchase.
Mistreatment, misuse, or tampering with the unit voids all warranty rights. Manual instructions and warnings must be observed at all times.
For initiation of a warranty claim in the USA please contact:
Quality Aspirators1419 Godwin Ln
Duncanville, TX 75116
P 972-298-2669
support@q-optics [email protected]
Outside the USA – please contact your local distributor.
No changes may be made to this warranty without being fi rst written, printed, and published by Quality Aspirators Inc.
Technical DataWeight of Battery Pack 6.5 ounces
Weight of Headlight See Data Sheet
Battery Type Li-Ion battery, 3.6 V / 4500 mAh
Battery Charge Time Up to 4 hours
Battery LifeLow intensity - ≈ 40+ hoursMedium intensity - ≈ 15.5 - 16 hoursHigh intensity - ≈ 7.5 - 8 hours
Light Intensity See Data Sheet
Operation Mode Continuous
Operation and Storage Temperature 32º to 95º F (0 to 35 C)
For charging the battery pack, simply plug the power supply cord interface into the charger interface on the bottom of the unit as shown.
Headlight
Belt ClipHeadlight
connection interface
Power supply connection interface
Intensity up
On/Off
Battery Status
Intensity down
PowerSupply
Radiant™
LIGHT SYSTEM
Battery Pack model #RADBL25
Power Supply model #FY0503000
5V - 2.5A DC power supply
