REBAR ACCESSORIES
E10 REBAR J-HOOK
E6Z REBAR TIE SPLICER
E6Z DOUBLE REBAR TIE SPLICER
Single splicer develops the 9,000 lb. (40.0 kN) working load and
18,000 lb. (80.1 kN) ultimate of WILLIAMS 1/2" high tensile tie
rod. Special design matches the angle of the serrations on the
rebar for maximum strength. Recommended torque on U-bolt
hex nuts is 40-ft. lbs. Available for No. 8 through No.11 rebar.
Double Rebar-Tie Splicers for 5/8" & 3/4" Tie Rods
Double splicer develops the full 19,000 lb. (84.5 kN) working load
and 38,000 lb. (169 kN) ultimate strength of WILLIAMS 3/4" high
tensile tie rods. Special design matches the rebar serration angle
to develop maximum strength. Available for No. 8 through No.11
rebar. Recommended torque on U-bolt hex nuts is 40-ft. lbs.
Also works with WILLIAMS 5/8" high tensile tie rods with an
11,250 lb. (50.0 kN) working load and 22,500 lb. (100 kN)
ultimate.
WILLIAMS Rebar J-Hook is an approved method of anchoring to
the rebar. Most popular uses include Nuclear Plants where weld-
ing to the rebar is not permitted and tying down battered wall
forms to resist uplift. J-Hooks are available in 3/8" and 1/2" diam-
eters for most popular rebar sizes.
State Rebar size (A) and J-Hook length (B) when ordering.
Rebar-Tie Splicer for 3/8" Tie Rods
Designed to work with WILLIAMS 3/8" high tensile tie rods.
Splicer develops a 4,900 lb. (21.8 kN) working load and 9,800 lb.
(43.6 kN) ultimate strength. Standard sizes for No. 6 through No.
14 rebar. Recommended torque of U-bolt hex nuts is 40 ft. Lbs.
Williams coupled reinforcing with rolled threads is the most con-
venient field connection possible. The high tensile couplings are
designed to exceed the full ultimate tensile strength of the thread-
ed rebar. Couplings and threaded rebar are available from
Williams in almost every standard diameter. They offer a tremen-
dous savings over field welding methods. Williams coupled rebar
meets the ACI code requirement 318-78 section 12.15.3 for
mechanical connections.
C2T COUPLED REBAR
E9B LIGHTWEIGHT SPICER
For Full Strength Rebar Couplings
See page 13 for C1T and C2T Couplings
or page 30 for C2D Flanged Couplings
A B
Patent No. 4,080,084
Patent No. 4,080,084
REBAR ACCESSORIES
E7Z REBAR BULKHEAD CLAMP
E5Z REBAR-LAPP SPLICER/LIGHT DUTY
E5Z DOUBLE REBAR-LAPP SPLICER/HEAVY DUTY
Light duty splicer with continuous strength for difficult forming
situations.
Rebar Bulkhead Clamps are designed for use on large or
small bulkheads when the rebar must run continuous.
The clamp uses Williams standard steel or malleable
wedge for fast assembly and minimum material costs.
Wedge clamp available up to No.8 Rebar. Rebars of
larger sizes use nuts and washers.
Rebar
Reccommended
Torque on Hex
Nuts
Working Load 2
to 1 S.F.
Lbs./kN
Average
Ultimate
Lbs./kN
*#4 & #5 15 ft. lbs. 3,750/ 16.7 7,500/ 33.4
#6 & #7 40 ft. lbs. 5,000/ 22.2 10,000/ 44.4
#8 thru #10 40 ft. lbs. 7,500/ 33.3 15,000/ 66.7
#11 40 ft. lbs. 10,000/ 44.5 20,000/ 89.0
Rebar
Working Load
2 to 1 S.F.
Lbs./kN
Average Ultimate
Lbs./kN
#6 & #7 10,000/ 44.5 20,000/ 89.0
#8 thru #10 15,000/ 66.7 30,000/ 133.4
#11 20,000/ 89.0 40,000/ 178.0
Ultimate Strengths to 40,000 lbs.
New rebar-lapp splicer designed for continuous strength of up to 40,000
lbs. Ties rebar together for use with tie rods. Recommended torque on
U-bolt hex nuts is 40-ft. lbs.
*Style different than shown (see detail A)
E9B
Lightweight Splicer
E-10
Rebar J-Hook
E5Z
Rebar-Lapp
Splicer
(Light Duty)
J7P
Rebar Collar
(shown on page 27)
C5T Threaded Shebolt
(shown on page 6)
D4M Hex-Lock Bracket
(shown on page 7)
E7Z Rebar
Bulkhead Clamp
Patent No. 4,080,084
Patent No. 4,080,084
Detail A