HEALTH & SAFETY DATA SHEET
ACME HP LINE BUBBLE FLUID 1. IDENTIFICATION OF THE SUBSTANCE / PREPARATION & COMPANY Name: PRO LIGHT CONCEPTS BUBBLE LIQUID Synonyms: FLUID (neutral) Supplied by: PRO LIGHT CONCEPTS LTD PERSEVERANCE MILL OLIVE LANE DARWEN LANCASHIRE BB3 3DQ WWW.PROLIGHT.CO.UK In Emergency call Prolight Concepts Ltd +44 (0) 1254 704111 2. COMPOSITION / INFORMATION ON INGREDIENTS Contains water based solution of acrylic polymers. Contains no substances in Part 1 of the approved Supply List, or with a maximum exposure limit (MEL) specified in Schedule 1 of COSHH. 3. HAZARDOUS INFORMATION No significant hazard to man or environment under normal conditions of handling and use. INGESTION - Low toxicity. EYE / SKIN - May cause irritation. INHALATION – Not applicable
4. FIRST AID MEASURES Exposure Route Symptom Treatment Inhalation: Mild irritation: Remove from exposure, rest and keep warm. In severe of nose & throat cases or if recovery is not very rapid or complete, seek medical attention. Skin Contact: Mild irritation: Drench the skin with plenty of water. Remove contaminated clothing and wash before re-use. If large areas of skin are damaged or if irritation persists seek medical attention. Eye Contact: Mild irritation: Irrigate thoroughly with water for at least 10 minutes. Obtain medical attention. Ingestion: Mild irritation of Gastro-intestinal tract: Wash out mouth with water. Do not induce vomiting If patient is conscious, give water to drink. If patient feels unwell, seek medical attention. 5. FIRE FIGHTING MEASURES – Not applicable 6. ACCIDENTAL RELEASE MEASURES Safety Precautions: Where appropriate PPE when handling - see section 8 Environmental Precautions: Prevent entry into drains and water courses Clean up Procedure: Bund or absorb material with sand, earth or other suitable absorbent material. If possible, transfer to a salvage tank, otherwise absorb residues and place in suitable labelled containers and hold for waste disposal see section 14. 7. HANDLING & STORAGE Safe Handling: Avoid prolonged skin contact. Avoid contact with eyes Ensure good ventilation of area. Avoid creating spray Do not breathe the undiluted vapor. Storage: Store in original closed containers only. Store at ambient temperature only. Store away from materials listed in section 10. 8. EXPOSURE CONTROLS & PERSONAL PROTECTION Respiratory: Type approved RPE for organic vapors and mists, if required. Hand: PVC coated or rubber gloves. Eye: Goggles or face shield. Skin: Overalls and boots. Hygiene Measures: Always wash thoroughly after handling chemicals. 9. PHYSICAL & CHEMICAL PROPERTIES Chemical Name and Formula Surfactants in an Aqueous Base (Tensides) Gas Number Not Applicable Packing Group Not Applicable Health Hazard Summary Not Applicable Risk Phrases Not Applicable Appearance Straw Yellow Liquid Odour Mild pH Value 7.5 Boiling Point/Range from 100˚C Melting Point/Range < -4˚C Solubility in water Completely miscible Induction Rate % 3% Vapour Pressure Not Applicable Bulk Density Not Applicable
Specific Gravity 1.01 Main Components Tensides (Fatty Alcohol Sulfates) Viscosity 20 degrees C_4 : 0 degrees C_7 Drainage Time 15 minutes 10. STABILITY & REACTIVITY Stability: Stable in normal conditions Known hazardous reactions: Possibility of explosive decomposition if combined with strong acids or bases at elevated temperatures. Conditions to avoid: Elevated temperatures Materials to avoid: Strong acids and bases: strong oxidisers Hazardous decomposition products: Oxides of carbon, including aldehydes 11. TOXICOLOGICAL INFORMATION May cause slight irritation to skin, eyes and mucous membranes. Large doses may produce adverse effects on liver, kidney's and central nervous system. No evidence in developmental toxicity studies for either embryotoxic or teratogenic effects. 12. ECOLOGICAL INFORMATION Mobility Liquid with low volatility, soluble in water, predicted to have high mobility in soil. Degradability The preparation is largely biodegradable. Accumulation Low 13. TRANSPORT INFORMATION No special precautions for transport. 14. DISPOSAL CONSIDERATIONS Substance Via an authorised waste disposal contractor to an approved waste disposal site, observing all local and national regulations. Container As for substance. Used containers must not be cut up or punctured until completely purged of product residues. 15. REGULATORY INFORMATION Supply label details In accordance with CHIP 2, Regulation 9. Label Name: Acme HP Line Bubble Fluid Symbol No risk or safety phrases stipulated. Risk phrases No risk or safety phrases stipulated. Safety phrases No risk or safety phrases stipulated. E.E.C. Number Use of this material may be governed by the following regulations: COSHH, HSWA, MHSW. Users are advised to consult these regulations for further information. The information contained in this data sheet does not constitute an assessment of workplace risk as required by other health and safety legislation.
16. OTHER INFORMATION No special training is required for handling this preparation other than normal precautions for safe handling of chemicals. This material is usually used for the production of synthetic bubbles in generic effects machines. It must not be used for any other purpose, or in any other equipment Further information can be obtained from the supplier, whose address and telephone number are given in section 1. 17. LEGAL DISCLAIMER The above information is based on the present state of our knowledge of the product at the times of publication of this data sheet. It is given in good faith, no warranty is implied with respect to the quality of the specification of the product. The user must satisfy himself that the product is entirely suitable for his purpose. If you have purchased the product for supply to a third party, it is your duty to take all necessary steps to ensure that any person handling and using the product is provided with the information in this sheet. If you are an employer it is your duty to tell your employees and others who may be affected by any hazard described in this sheet and of any precautions that should be taken.
