Download - Sample Report Write Up
-
7/30/2019 Sample Report Write Up
1/39
Contents
1. BUILDING DESCRIPTION : ...................................................................................................................... 2
2. SKETCHES AND DRAWINGS: .................................................................................................................. 2
3. DESIGN CRITERIA AND MATERIAL SPECIFICATION: .............................................................................. 7
4. DESIGN ASSUMPTIONS: ........................................................................................................................ 8
4.1. Assumptions made during First Stage: .......................................................................................... 8
4.2. Assumptions made during Second Stage: ..................................................................................... 8
5. DESIGN VALIDATION: ............................................................................................................................ 8
5.1. Objective : ..................................................................................................................................... 8
5.2. Section properties considered for validation:............................................................................... 9
5.3. Applied loads and Boundary conditions: .................................................................................... 13
5.4. 1D- RESULTS : .............................................................................................................................. 15
5.5. Discussion on 1D element results ............................................................................................... 29
5.6. 3D RESULTS ................................................................................................................................. 30
5.7. Discussion on 1D element results ............................................................................................... 39
-
7/30/2019 Sample Report Write Up
2/39
1.BUILDING DESCRIPTION :Width (I/I) = 25330 mmLength (column C/C) = 129720 mmBay spacing = 5@7560 + 8000 + 2@7500 + 8000 + 7@7560 +8000Clear height at side wall = 19500 mm
2.SKETCHES AND DRAWINGS:
-
7/30/2019 Sample Report Write Up
3/39
-
7/30/2019 Sample Report Write Up
4/39
-
7/30/2019 Sample Report Write Up
5/39
-
7/30/2019 Sample Report Write Up
6/39
-
7/30/2019 Sample Report Write Up
7/39
3.DESIGN CRITERIA AND MATERIAL SPECIFICATION:MATERIAL STD YIELD
STRENGTH TENSILESTRENGTH COMPONENTSASTM A 572 GR50 345 MPA 450 MPA CONNECTOR ANGLE, SHOE, FRAME/TOP-AISLECONNECTOR PLATESASTM A 1011/ 570 GR50 345MPA 450 MPA UPRIGHTS, CROSS BEAMS, FRAME BRACINGS, SPLICEIS 4923 210 MPA 410 MPA FRAME CONNECTORSASTM A 325 M
660 MPA
830 MPA
FASTNERS, EXPANSION BOLTS
IS2016 WASHERSIS 2062 240 MPA 410 MPA BRACE RODS (PLAN, AISLE, SPINE)
-
7/30/2019 Sample Report Write Up
8/39
4.DESIGN ASSUMPTIONS:During the validation of SANATAN Plant layout, the following assumptions are made in order to simplify or
make the validation more conservative.
Design validation carried out at two stages. In first stage, the whole plant was modeled with equivalent 1-
Dimensional BEAM element with appropriate Cross-sectional properties. In Second stage, the sub-model of
plant is modeled with 2-Dimensional SHELL elements with appropriate thickness properties.
4.1. Assumptions made during First Stage:- To be conservative the weakest section properties considered for modeling all components in SANTAN Plant
-Section properties calculated at C.G of the weakest section for each component
-Complete plant layout is modeled as three blocks and rested on uprights with fixed boundary condition [all
DOF constrained]
-Shoe is not considered during 1D element analysis [BEAM model]
-Live loads and Seismic loads distributed at the joint location of Upright and Box beams on which pallets are
mounted
4.2. Assumptions made during Second Stage:-Connections between various components are modeled with rigid elements
-Components are placed at the original position and orientation in assembly condition
-Live loads are applied over the top surface of box beam, in the form of uniformly distributed load [pressure]
-Seismic loads are applied at the rigid elements used to model the joints between uprights and box-beams
5.DESIGN VALIDATION:5.1. Objective :
To validate the structural design proposed by Kirby after analysis of the same with live load and dead load
with seismicloads applied following the code book IS-1893.The proposed structure was already in accordance with the EN 155512, EN 15620.(please correct the content accordingly to maintain a standard).
-
7/30/2019 Sample Report Write Up
9/39
5.2. Section properties considered for validation:
-
7/30/2019 Sample Report Write Up
10/39
-
7/30/2019 Sample Report Write Up
11/39
-
7/30/2019 Sample Report Write Up
12/39
-
7/30/2019 Sample Report Write Up
13/39
5.3. Applied loads and Boundary conditions:
-
7/30/2019 Sample Report Write Up
14/39
-
7/30/2019 Sample Report Write Up
15/39
5.4. 1D- RESULTS :
-
7/30/2019 Sample Report Write Up
16/39
-
7/30/2019 Sample Report Write Up
17/39
-
7/30/2019 Sample Report Write Up
18/39
-
7/30/2019 Sample Report Write Up
19/39
-
7/30/2019 Sample Report Write Up
20/39
-
7/30/2019 Sample Report Write Up
21/39
-
7/30/2019 Sample Report Write Up
22/39
-
7/30/2019 Sample Report Write Up
23/39
-
7/30/2019 Sample Report Write Up
24/39
-
7/30/2019 Sample Report Write Up
25/39
-
7/30/2019 Sample Report Write Up
26/39
-
7/30/2019 Sample Report Write Up
27/39
-
7/30/2019 Sample Report Write Up
28/39
-
7/30/2019 Sample Report Write Up
29/39
5.5. Discussion on 1D element resultsTo be discussed before finalizing
-
7/30/2019 Sample Report Write Up
30/39
5.6. 3D RESULTS
-
7/30/2019 Sample Report Write Up
31/39
-
7/30/2019 Sample Report Write Up
32/39
-
7/30/2019 Sample Report Write Up
33/39
-
7/30/2019 Sample Report Write Up
34/39
-
7/30/2019 Sample Report Write Up
35/39
-
7/30/2019 Sample Report Write Up
36/39
-
7/30/2019 Sample Report Write Up
37/39
-
7/30/2019 Sample Report Write Up
38/39
-
7/30/2019 Sample Report Write Up
39/39
5.7. Discussion on 1D element resultsTo be discussed before finalizing