Project Tender (If applicable). 1
Services Provided by N.E.D.F. 2
Standard Steel Door Frames – Data Sheet. 3
Standard Steel Door Frames – Profiles. 4 – 5
Fire Rated Steel Door Frames – Data Sheet. 6
Fire Rated Steel Door Frames – Profiles. 7 – 9
Steel Door Frames – Fixing Methods. 10
Steel Door Frames – Frame Details. 11
Special Steel Door Frames – Profiles. 12
Special Steel Door Frames. 13
Steel Cavity Slider Units – Data Sheet. 14
Steel Cavity Slider Units – (Fully Assembled Model) – Schematic. 15
Steel Sheeted Door Panels – Data Sheet. 16
Steel Sheeted Door Panels – Schematic. 17
Steel Door Panels – Data Sheet. 18
Steel Door Panels – Schematic. 19
Steel Louvre Door Panels / Fixed Louvres – Data Sheet. 20
Steel Louvre Door Panels – Schematic. 21– 24
Chevron Louvre – Schematic. 25
TABLE OF CONTENTS
NEDF is the manufacturer and supplier of:
Standard & Fire Rated Steel Door Frames
Special Steel Door Frames (Made to measure)
Lead Lined Steel Door Frames
Stainless Steel Door Frames
Cavity Slider Door Frames
Steel Louvre Doors & Fixed Panels
Steel Doors
Steel Security Doors
Steel Sheeted Timber Doors
We are also the supplier of:
Fire Rated & Smoke Doors
Solid Core Timber Doors
Hollow Core Timber Doors
NEDF is qualified for the “Certification” of Fire Rated Door sets.
NEDF also carries out general Sheet Metal Work in Zinc, Galvanised,
Colourbond or Stainless Steel. This includes Light Industrial Fabrication on Gates, Rails,
Grilles etc..
N.E.D.F. is proudly Australian owned and uses only “Australian” Steel for all products
manufactured.
SERVICES PROVIDED
Standard Steel Door Frames are manufactured from either 1.1mm or 1.5mm Zincanneal,
Galvanised or Grade 304 “Brushed” Stainless Steel sheet conforming to AS1397.
Frames incorporate either a double or single rebate as may be required or as a Plain
Frame for Double Acting or Sliding doors. Standard Steel Door Frames are supplied
either unassembled or welded, smoothed and shop primed with a rust inhibitive,
phosphate based primer.
Stand Frames are manufactured and supplied with:
Three Hinge plates (drilled & tapped) per hinge stile
Provision for Universal Lock Strike – 1030mm from floor
Removable Spreader Bars
Mortar Boxes for Masonry applications
Base Fixing Plates
Slot & Lug assembly for “Un-Assembled” Frames
Two Resilient Rubber Buffers per Lock Stile
Standard Steel Door Frames incorporate a 15mm Stop and a rebate to accommodate a
35mm, 40mm or 45mm door panel. For Solid Core Doors, a third hinge is fitted.
Generally frames are supplied with galvanised wire fixing ties for new masonry walls.
They may be fitted with Countersunk Fixing Holes & Tube Spacers for existing walls. Stud
Clips or Fixing Straps are used for Stud Walls.
All Frames are warranted as per N.E.D.F. “Terms & Conditions of Sale”
STANDARD STEEL DOOR FRAMES
PRODUCT DATA SHEET
STANDARD STEEL DOOR FRAME PROFILES
95
38
Suitable for:
90mm Block work
64mm Stud + 13mm Lining Each Side
TYPE S1
105
Suitable for:
100mm Block work
76mm Stud + 13mm Lining Each Side 38
TYPE S2
114
Suitable for:
114mm Brickwork
90mm Stud + 10mm Lining Each Side
38
TYPE S3
120
Suitable for:
90mm Stud + 13mm Lining Each Side 38
TYPE S4
Manufacturing Tolerances +/- 2mm
STANDARD STEEL DOOR FRAME PROFILES
145
38
Suitable for:
140mm Blockwork
Cavity Wall
TYPE S5
195
Suitable for:
190mm Blockwork
38
TYPE S6
265
Suitable for:
Cavity Brick Wall
38
TYPE S7
76 - 195
Suitable for:
Surface Mounted Sliding Doors &
Double Acting Doors
38
TYPE S8
Manufacturing Tolerances +/- 2mm
Fire Rated Steel Door Frames are manufactured to the requirements of AS/NZ1905.1 from
either 1.1mm, 1.5mm or 2.5mm Zincanneal or Galvanised Steel conforming to AS1397.
Frames incorporate either a double or single rebate as may be required. Fire Rated
Steel Door Frames are supplied welded, smoothed and shop primed with a rust inhibitive,
phosphate based metal primer.
Frames are manufactured and supplied with:
Three Hinge plates (drilled & tapped) per hinge stile
Provision for Universal Lock Strike per lock stile – 1030mm from
floor.
Removable Spreader Bars
Mortar Boxes for Masonary Wall applications
Base Fixing Plates
Two Resiliant Rubber Buffers per Lock stile
Re-enforcing for a Surface Mounted Door Closer
Fire Rated Steel Door Frames incorporate a 25mm Stop and a reveal to accommodate
either a 37mm or 47mm door panel. Door panels over 2300H x 1020W a fourth hinge is
fitted.
Generally frames are supplied with galvanised wire fixing ties for new masonary walls.
They may be fitted with countersunk holes and tube spacers for existing masonary walls
or welded fixing straps for stud wall applications. (See “Fixing Methods – Page 16)
All frames are warranted as per N.E.D.F. “Terms & Conditions of Sale”
FIRE RATED STEELDOOR FRAMES
PRODUCT DATA SHEET
FIRE RATED STEEL DOOR FRAME PROFILES
95
38
Suitable for:
90mm Blockwork
64mm Stud + 13mmLining each side
TYPE FR1
105
Suitable for:
100mm Blockwork
76mm Stud + 13mm Lining each side
38
TYPE FR2
114
Suitable for:
110mm Brickwork
76mm Stud + 16mm Lining each side
38
TYPE FR3
120
Suitable for:
90mm Stud + 13mm Lining each side 38
TYPE FR4
Manufacturing Tolerances +/- 2mm
FIRE RATED STEEL DOOR FRAME PROFILES
130
38
Suitable for:
90mm Stud
plus 2 x 13mm Lining each side
TYPE FR5
145
Suitable for:
140mm Blockwork
38
TYPE FR6
195
Suitable for:
190mm Blockwork
38
TYPE FR7
270
Suitable for:
Cavity Brick Wall
38
TYPE FR8
Manufacturing Tolerances +/- 2mm
FIRE RATED STEEL DOOR FRAME PROFILES
95
63
Suitable for:
47mm Thick Fire Door
90mm Blockwork
TYPE FR9
Suitable for:
47mm Thick Fire Door
100mm Blockwork
TYPE FR10
Suitable for:
2.5mm Thick Frame
TYPE FR11
Suitable for:
Inverted Fire Frame for
Double Acting Doors
TYPE FR12
95 - 270
63
114 -195
38
105
63
Manufacturing Tolerances +/- 2mm
STEEL DOOR FRAME—FIXING METHODS
Single Masonary Cavity Masonary
Cavity Masonary Tube Fixing
Cavity Masonary Stud Wall Fixing
Weather Mould Stud Fixing Strap
STEEL DOOR FRAMES—FRAME DETAILS
Overall Height
Reveal Height
Rebate Height
Reveal Width
Clear Opening Width
Overall Width
L.H. Door R.H. Door
DOOR HANDING
STEEL DOOR FRAMES SPECIAL PROFILES
Architectural Frames
Stormproof Frame
c/w Louvre Shutters
Single Rebate Frame for
Pre Cast Concrete Walls
Or Access Panels
Cap Frame
(To cover existing or damaged
Frames)
Door Panel Louvre Panel
Manufacturing Tolerances +/- 2mm
SPECIAL STEEL DOOR FRAMES
Steel Door Frame
With Sidelights
Steel Door Frame
With Highlight
Steel Door Frame
With Louvre
Steel Door Frame
With Sidelight
Steel Factory Windows
Manufacturing Tolerances +/- 2mm
The N.E.D.F. Cavity Slider Unit has been designed for an extended life and to be
maintenance free. Unlike its timber counterparts, the steel Cavity Slider is extremely rigid
as a result of the welded manufacturing procedure; there is no movement within the unit
or wall lining when installed. The unit is supplied complete with a track system
incorporating two four wheeled rollers per door panel. The tracking system will not allow
the door panel to “jump” off the track.
The Cavity Slider Units are manufactured from either “Zincanneal”, “Galvanised” or
“Brushed Stainless Steel” and are fully welded throughout. The units are designed main-
ly for a 92mm Stud Wall but many varying applications are available.
Each unit is fitted with the following:
Rubber Stop Buffers
Floor Fixing Plates
Tracking System
Bottom Guides
Stud Fixings
Pelmets
An optional feature is the inverted meeting stile that may be applied to single door units.
This stile allows the leading edge of the door panel to protrude into the face of the stile
when the door is in the closed position thus eliminating any gap or “see through”. This is
a unique combination for En-Suites or Walk In Robes.
The Zincanneal units are supplied shop primed ready for paint or powder coated to a
selected colour from the “Dulux” range of colours.
The Galvanised units are supplied unprimed but all worked areas and joins are Cold
Galvanised.
Cavity Slider Units are available in all standard single & double door sizes or special sizes
up to 3000 in height and 2500 in width.
Cavity Slider Units can be supplied either fully assembled or unassembled for “on site”
assembly.
The following schematics detail the fabrication and installation details.
The product is warranted as per N.E.D.F “Terms & Conditions of Sale”.
STEEL CAVITY SLIDER UNIT
PRODUCT DATA SHEET
STEEL CAVITY SLIDER UNITS
Cavity Stiles
Pelmets
Door Track
DOUBLE DOOR UNIT
SINGLE DOOR UNIT
Pelmets
Door
Cavity Stiles
The N.E.D.F. Steel Sheeted Doorset offers quality, security and an appealing smooth or
embossed finish and can be adapted to all facets of the Construction Industry from
Commercial and Industrial to Domestic applications. The product is available in either
standard solid Core or fire rated applications.
The steel sheeted door panels are manufactured utilising either a weatherproof solid
core door panel or an approved fire rated door panel. The selected steel sheeting is
adhered to the face or faces of the door panel. The edges of the panel are capped all
round with the selected steel and weatherproofed. Products manufactured from
Zincanneal Steel are then shop primed with a rust inhibitive, phosphate based primer,
ready for paint.
Selected steel facings utilised in the manufacture of the products are:
Zincanneal
Galvanised
Brushed Stainless Steel
Embossed Stainless Steel
Colourbond
Embossed Colourbond
All steel facings range in thickness from 0.6mm to 1.5mm.
Options available include Anti-Jemmy Bars, Viewing Panels, Louvre Inserts, Return Air
Grilles and Powdercoating with a selected colour from the “Dulux” range of colours.
Pairs of doors are fitted with a full length 40mm x 3mm steel overlapping meeting stile to
the active leaf to afford added security and weatherproofing.
The Steel Sheeted Door may be factory fitted to its accompanying steel Door Frame and
despatched as a complete unit.
Preparations for Door Hardware may be applied if the Hardware is supplied by the Client
prior to the commencement of manufacture.
Each Doorset is warranted as per N.E.D.F “Terms & Conditions of Sale”.
STEEL SHEETED DOORSETS
PRODUCT DATA SHEET
STEEL SHEETED DOORSETS
PLAIN DOORSET DOORSET WITH VIEW PANEL
DOORSET WITH AIR GRILLE DOORSET WITH LOUVRES
The N.E.D.F. Steel Door sets offer quality, security and a smooth or embossed finish and
can be adapted to all facets of the Construction Industry from Domestic to Commercial
and Industrial. Modifications to our standard manufacturing procedures are available
to suit most specialised projects.
The Steel Door Panels are constructed with an RHS inner frame with cross bracing. The
inner frame is filled with HD Polystyrene and a “Mid-Rail” section is formed containing a
wooden block to accommodate the door Hardware. The outer faces are then sheet-
ed. The edge sections of the door panel is capped all round with the same material as
the facings.
Steel Doorsets can be manufactured using one of the following materials:
Zincanneal
Galvanised Steel
Colourbond
Brushed or Embossed Stainless Steel
Pairs of doors are fitted with a 40mm x 3mm Anti Jemmy Bar. This bar may also be fitted
to the leading edge of a Single Door Panel. Zincanneal doors are shop primed prior to
despatch. Powder coating is available in selected colours from the “Dulux” range.
Door Panels may be pre-fitted to their accompanying steel door frame and despatched
as a complete unit.
Door Panels may be fitted with Air Grilles, View Panels, Louvres or Perforated Steel Sheet.
The Door sets are available in all sizes including double pairs with centre mullion or
overhead fixed or removable transoms.
Each Door set is warranted as per N.E.D.F. “Terms & Conditions of Sale”
STEEL DOORSETS
PRODUCT DATA SHEET
STEEL DOORSETS
SINGLE DOOR PANEL
Styrene Infill
RHS Frame
Lock Block
Steel Door Frame
DOUBLE DOOR PANELS
DOUBLE DOORSETS WITH LOUVRES OVER, VIEW PANELS, AIR GRILLES & CENTRE MULLION
The N.E.D.F. Steel Louvres and Steel Louvre Door sets offer security, ventilation and
weatherproofing.
Our louvres are adaptable to all facets of the Construction Industry from Commercial
and Industrial to Domestic. With their pleasing “Colourbond” finish, they enhance the
appearance of plant rooms, sub stations, car parks and any other application for which
they may be required.
The units are manufactured from either Zincanneal, Galvanised or Brushed Stainless
Steel. Steel Mesh may be fitted to the rear face of the units for vermin proofing.
An optional 10mm steel rod may be applied to each louvre vane for added security.
Louvre Door sets incorporate provision for the required door hardware and are supplied
pre-fitted to the accompanying Steel Door Frame prior to despatch.
Single Louvre Door sets are available in all sizes from 2040 x 620 to 3000 x 1200 and
include provision for door hardware.
Double Louvre Door sets are available in standard pairs of 2040 x (2)620, 2040 x (2)720 or
2040 x (2)820 with special sizes up to 3000 x 2400. Pairs of doors are fitted with an
anti-jemmy bar to the active leaf and provision for door hardware.
Fixed Louvre Panels are available in various shapes and sizes up to 3000 x 2400 and are
manufactured to suit the many varied types of wall construction used today.
All Louvre sets, with the exception of stainless steel, are supplied “Powdercoated” in a
selected colour from the “Dulux” range.
The products are warranted as per N.E.D.F. “Terms & Conditions of Sale”
STEEL LOUVRES & LOUVRE DOORSETS
PRODUCT DATA SHEET
STEEL LOUVRES—MANUFACTURING PROFILE
Outer Capping
Vermin Proof Mesh
Louvre Vanes
Optional 10mm Steel Rod
Midrail
Outer Capping
Louvre Vanes
38 x 38 SHS
The louvre blades will be welded to 38 x 38 x 1.6mm SHS steel section that makes the
perimeter of the door panel. The SHS will then be fully capped with 1.2mm zincannel.