![Page 1: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/1.jpg)
Thank you for purchasing the RAW Design Scorpion Tips for your Suzuki M-109R. The instructional sheets that follow are thoroughly detailed and should be studied
BEFORE picking up a tool. Take your time, work safe and you will enjoy your new exhaust within a few hours.
These are the tools you will need:
- Safety Glasses - Saftey Gloves
- Ear Plugs - Grinder with cutoff wheel and / or Sawzall with fine blade
- Plastic or rubber mallet - Metric Allen Key Set
- Metric Box Wrench set - Metric Socket set with assorted extensions, swivels, etc.
- Cut off pliers - Screw Drivers
- Drill Motor with 1/8” bit
![Page 2: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/2.jpg)
Remove Seat
Remove Snap pin from cover. Use a pencil point or something similar to depress center of pin during removal.
![Page 3: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/3.jpg)
This is the pin. Don’t lose it.
Remove Allen bolt from lower side cover
![Page 4: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/4.jpg)
Gently remove plastic side cover and panel. This will pull off with firm pressure.
![Page 5: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/5.jpg)
Remove 2 Allen bolts from chrome SET (Synchronized Exhaust Tuning) valve cover
![Page 6: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/6.jpg)
Remove chrome SET valve cover
![Page 7: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/7.jpg)
Remove Allen bolt from heat shied
Remove heat shield.
![Page 8: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/8.jpg)
Be careful not to lose this grommet when removing shield. You will need it latter.
Remove forward and rear support bolts for upper tube.
![Page 9: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/9.jpg)
Loosen 2 clamp bolts on top tube
![Page 10: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/10.jpg)
Pull back and up to remove top tube. Slight twisting may help.
![Page 11: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/11.jpg)
Disconnect wires for SET exhaust valve.
![Page 12: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/12.jpg)
Remove 1Allen bolt and plastic side cover with gentle pressure.
![Page 13: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/13.jpg)
Remove lower bolt from exhaust hanger. Remove nut from upper stud. Exhaust hanger
should stay in place on stud for now. (Shown below)
![Page 14: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/14.jpg)
Remove lower hanger mount bolt.
![Page 15: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/15.jpg)
Remove bolts from front and rear exhaust pipes.
![Page 16: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/16.jpg)
Remove exhaust and place on a covered workbench so you don’t scratch any chrome.
![Page 17: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/17.jpg)
Remove exhaust actuator from support frame. There is no need to disconnect cables.
![Page 18: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/18.jpg)
Remove front and rear bolts from exhaust support frame
![Page 19: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/19.jpg)
Remove 3rd bolt from exhaust support frame and remove frame.
![Page 20: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/20.jpg)
Remove 1 bolt and heat shield.
![Page 21: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/21.jpg)
Remove 1 bolt and clamp. Put lower tube and exhaust manifold assembly to the side for
now.
![Page 22: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/22.jpg)
![Page 23: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/23.jpg)
On the upper exhaust tube, remove bolts on the clamp that holds on the heat shield. With
a screwdriver, spread flanges of the clamp and remove heat shield.
![Page 24: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/24.jpg)
EXTREMELY IMPORTANT!!! The upper and lower tubes of your exhaust need to be cut differently from each
other in order for the Scorpion Tips to attach properly. DO NOT CUT until you are absolutely positive you understand where they are to be cut. It’s not rocket science,
but you have to pay attention.
Upper Tube
The upper pipe must be cut just behind the weld bead (towards the fat end of the pipe) so that the weld remains with the flange. See above picture. It does not have to be perfectly
straight or perfectly on the edge of the weld; just as close as you can get it without removing the weld.
![Page 25: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/25.jpg)
This is what it should look like after the cut. Take the inner piece of scrap you see above
and discard.
The welds on each pipe are slightly different. They will need to be ground until the
Scorpion tip fits snuggly. DO NOT screw or weld them on yet. You will want to be able to turn them up or down latter to get the angle you want for your bike.
![Page 26: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/26.jpg)
This is what the upper pipe should now look like.
Now put the upper pipe to the side.
![Page 27: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/27.jpg)
On the lower pipe there are 2 welds holding on the heat shield. Grind off these welds and
remove the heat shield.
![Page 28: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/28.jpg)
Picture shows weld ground off
![Page 29: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/29.jpg)
EXTREMELY IMPORTANT!!! The upper and lower tubes of your exhaust need to be cut differently from each
other in order for the Scorpion Tips to attach properly. DO NOT CUT until you are absolutely positive you understand where they are to be cut. It’s not rocket science,
but you have to pay attention.
LOWER PIPE
The lower pipe must be cut just ahead of the weld bead (towards the inlet end of the
pipe) so that the weld is removed from the flange. See above picture. It does not have to be perfectly straight or perfectly on the edge of the weld; just as close as you can get it
while removing the weld.
![Page 30: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/30.jpg)
Cut exhaust support as shown above. Discard part on left. Clean up the cut on the part on
right and paint exposed steel with something like Rustoleum black spray paint.
Reattach frame to lower exhaust and manifold.
![Page 31: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/31.jpg)
Reinstall exhaust actuator
Put lower exhaust system back on bike. Reinstall nut on stud.
![Page 32: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/32.jpg)
Reinstall nuts / studs from manifold to engine, front and back pipes. This is a good time to inspect your exhaust gaskets in the heads. Replace if you have any question as to their
integrity.
Reinstall lower bolt in exhaust support.
![Page 33: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/33.jpg)
Reinstall exhaust support bottom bolt
![Page 34: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/34.jpg)
Reattach SET control wires.
Reinstall Black Trim panel and bolt
![Page 35: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/35.jpg)
Reinstall heat shield on upper tube. Do Not set the clamp tight. Just finger tight on the bolts.
![Page 36: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/36.jpg)
EXTREMELY IMPORTANT!!! The following shows how to TEMPORARILY attaché your new Scorpion Tips. They must be tack welded in place to permanently affix. See “Welding instructions” below.
Slip on Scorpion pipe tip to lower flange. Rotate to desired angle
![Page 37: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/37.jpg)
Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion tip as a loose assembly to get the desired angle you
want for the tips. Do the same for the bottom tip to make sure both are aligned. Take your time. This sounds more complicated than it is.
Once you have everything lined up where you like it, use a felt tip pen or similar marker to mark a small line across each of the adjoining parts. This creates a reference point to
realign everything during the next step.
Move to top heat shield so you can get at the joint of the inner tube and Scorpion Tip. With a 1/16” drill bit, use one of the pilot holes in the tip to drill through the inner tube.
Use one of the supplied sheet metal screws to fasten Tip to inner tube.
![Page 38: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/38.jpg)
Remove the top tube heat shield and Scorpion tip to gain access to the lower assembly.
Make sure your alignment marks are in-line. Drill and screw Tip to inner tube as you did above.
![Page 39: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/39.jpg)
Reinstall upper tube and heat shield. Check for alignment. Tighten clamp on front of heat
shield. This will hold shield and inner tube to manifold.
Reinstall remaining guards, trim pieces and seat.
Make one more thorough check of all the pieces you just assembled to make sure everything is correct and tight. If you are sure everything is in order, go ahead and start
your bike. Check for any exhaust leaks.
![Page 40: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/40.jpg)
Now take the bike DIRECTLY to a qualified welder. A muffler shop may be good. Have the welder place 2 or 3 tack welds on each pipe to tip joint. Each one should be
approximately ¾” long.
![Page 41: Thank you for purcha#132E75 - Raw Design Cycles · Slip upper tube and heat shield onto upper manifold. You will need to twist and adjust the inner tube, heat shield and Scorpion](https://reader033.vdocuments.net/reader033/viewer/2022050411/5f884ae0234e4819c31beafd/html5/thumbnails/41.jpg)
Spare parts and approximately 15 pounds removed from you bike
Enjoy and Ride Safe