-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
1/74
UMTS INDOOR RF DESIGN GUIDELINE
Document number: UMT/DCL/APP/035536
Document issue: 4.1 / ENDocument status: StandardDate: 21/JUL/2011
External document
Copyright2003-2008 Alcatel-Lucent, All Rights Reserved
Printed in France
ALCATEL-LUCENT CONFIDENTIAL:
The information contained in this document is the property of Alcatel-Lucent. Except as specifically authorized in
writing by Alcatel-Lucent, the holder of this document shall keep the information contained herein confidential andshall protect same in whole or in part from disclosure and dissemination to third parties and use same for
evaluation, operation and maintenance purposes only.
The content of this document is provided for information purposes only and is subject to modification. It does not
constitute any representation or warranty from Alcatel-Lucent as to the content or accuracy of the information
contained herein, including but not limited to the suitability and performances of the product or its intended
application.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
2/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 2/74
CONTENTS
1 INTRODUCTION............................................................................................................................5
1.1 INDOORRFCOVERAGEGUIDELINE..................................................................................5
1.2 SCOPE OF THIS DOCUMENT .......................................................................................................5
1.3 AUDIENCE FOR THIS DOCUMENT ................................................................................................5
2 GENERALITIES ABOUT INDOOR ...............................................................................................6
2.1 INDOOR SPECIFICITIES ..............................................................................................................6
2.2 INDOORDESCRIPTION........................................................................................................8
3 SAFETY NORMS...........................................................................................................................9
3.1 PRINCIPLE ................................................................................................................................9
3.2 MINIMUM DISTANCE REQUIREMENT ..........................................................................................10
4 OEM AND PRODUCTS SOLUTIONS.........................................................................................11
4.1 DISTRIBUTED ANTENNA SYSTEM (DAS) ....................................................................................11
4.1.1 Passive distribution.......................................................................................................114.1.2 Active.............................................................................................................................134.1.2.1 Bi-directional amplifiers (BDA) ........................................................................................................134.1.2.2 In building fiber optic and/or electrical extension..............................................................................14
4.1.2.2.1 Fiber optic system........................................................................................................................144.1.2.2.2 electrical system ................................................................ .......................................................... 154.1.2.2.3 Example of existing system: Unison system from LGCWireless................ ................................ 16
4.2 REPEATER..............................................................................................................................17
4.2.1 RF Repeaters solution ..................................................................................................174.2.2 Optical repeaters...........................................................................................................18
4.3 INDOOR SMALL CELL-CELL NODE-B ...........................................................................................20
4.3.1 Noise figure ...................................................................................................................20
5 RADIO DESIGN METHODOLOGY .............................................................................................21
5.1 PRINCIPLE &CONSTRAINTS .....................................................................................................21
5.2 DIMENSIONING SERVICE &TRAFFIC ASSUMPTIONS ...................................................................22
5.3 LBANALYSIS ..........................................................................................................................23
5.3.1 Engineering margins .....................................................................................................235.3.1.1 Shadow margin calculation for QoC..................................................................... ............................. 235.3.1.2 DAS losses .................................................................. ............................................................. ..........235.3.1.3 Obstacles losses..................................................................................................................................245.3.2 UPlink parameters.........................................................................................................245.3.3 DOWNLINK BUDGET...................................................................................................24
CPICH power calculation....................................................................................................................25 Common Channels power setting .......................................................................................................25 Other parameters .................................................................................................................................26
5.4 RFDESIGNTARGETS........................................................................................................26
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
3/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 3/74
5.4.1 Minimum attenuation required and Total EIRP recommended.....................................275.4.2 Coverage target ............................................................................................................275.4.2.1 Shared carrier configuration...............................................................................................................27
3rdfloor and highest .............................................................................................................................27
2nd
, 1st & ground floors,.......................................................................................................................28 RF recommendations for distance between antenna and nearest window......................................28
5.4.2.2 Dedicated carrier configuration..........................................................................................................295.4.3 Interference criteria .......................................................................................................295.4.3.1 Ec/I0 targets .......................................................................................................................................295.4.3.2 Polluted area & overlap analysis................................................................................................. ..........305.4.4 Neighboring plan / Scrambling Code plan ....................................................................30
5.5 OPTIMIZATION....................................................................................................................31
5.5.1 Methodology..................................................................................................................315.5.2 Optimization phases......................................................................................................315.5.2.1 Optimization and validation based on RF field analysis .................................................................... 31
5.6 UMTSVS OTHER TECHNOLOGIES INDOOR NETWORK COEXISTENCE ..........................................33
5.6.1 Separated frequency band............................................................................................335.6.2 UMTS shared same frequency band with CDMA /UMTS/GSM....................................335.6.2.1 UMTS & GSM...................................................................................................................................345.6.2.2 UMTS & CDMA................................................................................................................................365.6.2.3 UMTS & UMTS ................................................................................................................................36
5.7 HSXPADESIGN CONTRAINTS AND DEPLOYMENT STRATEGY ......................................................37
5.7.1 HSDPA..........................................................................................................................375.7.1.1 UL impact on R99 Eb/No ..................................................................... ............................................ 375.7.1.2 DL HS-SCCH.....................................................................................................................................385.7.1.3 HSUPA DL common channels impact...............................................................................................38
6 ANALYSIS OF EACH RF INDOOR SOLUTIONS ......................................................................40
6.1 NATURAL INDOOR PENETRATION..............................................................................................40
6.1.1 Description ....................................................................................................................406.1.2 advantages & drawbacks..............................................................................................41
Advantages: ..........................................................................................................................................41Drawbacks: ...........................................................................................................................................41
6.2 MASSIVE PUBLIC NETWORK INDOOR DEPLOYMENT ...................................................................41
6.2.1 Interference analysis in Shared carrier configuration ...................................................416.2.1.1 best server between Indoor small cell vs macro-cell ..................................................................... .....416.2.1.2 indoor small cell interfers macro network users.................................................................................436.2.2 Dedicated carrier...........................................................................................................446.2.3 Number of scrambling code allocated to indoor small cell network ..............................44
Worst case study...................................................................................................................................45 Recommendations for standard cases ................................................................................................47
6.2.4 Conclusion on strategy between shared carrier and dedicated carrier configuration...476.3 DASDEPLOYMENT .................................................................................................................47
6.3.1 Power transmitted per antenna port and minimum attenuation required between RRHconnector and antenna port .........................................................................................................486.3.2 Field analysis ................................................................................................................496.3.2.1 Site survey..........................................................................................................................................49
6.3.2.1.1 Pre requisite:................................................................................................................................496.3.2.1.2 Equipment needed: ............................................................ .......................................................... 496.3.2.1.3 Deliverables.................................................................................................................................49 6.3.2.1.4 Site classification.........................................................................................................................51
6.3.2.2 RF measurements .............................................................. ................................................................ .51
6.3.2.2.1 CW calibration measurements.....................................................................................................526.3.2.2.2 Penetration factor determination: ................................................................................................52
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
4/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 4/74
6.3.2.2.3 Ceiling/floor penetration: ............................................................................................................526.3.2.2.4 Indoor propagation for structure studies......................................................................................536.3.2.2.5 Equipment used ................................................................... ........................................................ 53
6.3.2.2.5.1 Transmission.........................................................................................................................54
6.3.2.2.5.2 Reception part.......................................................................................................................546.3.2.2.5.3 Process & key points ..................................................................... ....................................... 54
6.3.3 RF indoor Design solutions...........................................................................................576.3.3.1 Indoor design with repeater and passive DAS....................................................................................57
6.3.3.1.1 RF repeater .............................................................. ................................................................... .576.3.3.1.1.1 usage.....................................................................................................................................57 6.3.3.1.1.2 RF recommendations............................................................................................................596.3.3.1.1.3 ADVANTAGES & DRAWBACKS .................................................................................... 60
6.3.3.1.2 Optical Repeater ............................................................ ............................................................. .616.3.3.1.2.1 USAGE.................................................................................................................................61 6.3.3.1.2.2 RF Recommendations...........................................................................................................626.3.3.1.2.3 Advantages & drawbacks ............................................................... ...................................... 62
6.3.3.2 Indoor dedicated Macro Node-B (or RRH) with das .........................................................................63
6.3.3.2.1 Link budget..................................................................................................................................636.3.3.2.2 Using ...........................................................................................................................................646.3.3.2.3 advantages & drawbacks ....................................................... ...................................................... 65
6.3.4 Distributed antenna system installation ........................................................................656.3.4.1 Type of DAS recommendations........ ..................................................................... ............................ 65
6.3.4.1.1 Coaxial cables..............................................................................................................................656.3.4.1.2 Optical fibber...............................................................................................................................666.3.4.1.3 comparison of different DAS solutions .................................................................... ...................67
6.3.4.2 Radiating elements recommendations................................................................................................686.3.4.2.1 Antennas......................................................................................................................................68 6.3.4.2.2 Radiating cables...........................................................................................................................696.3.4.2.3 Mixed termination: ................................................................ ...................................................... 716.3.4.2.4 Combiners ...................................................................................................................................72
7 SUMMARY OF INDOOR SOLUTIONS.......................................................................................73
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
5/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 5/74
1 INTRODUCTION
One of the most important challenges today is the provision of reliable, seamless indoor coverage
for wireless mobile communications.
In fact, subscribers from mobile and Internet markets are merging into one single market and the
term hotspots is more and more met everywhere.
3G introduction leads to new services, introducing higher traffic and therefore higher capacity
needs, but also higher revenue opportunities.
Indoor users are the most likely to use these services. However, users will only accept to change
to UMTS if the network quality is at least as good as the 2G networks, especially indoors.
A better indoor coverage penetration can be interesting, essential concern are corporate servicesoffer and company traffic capture.
To realize a good indoor Design, minimum of radio knowledge must be essential. Three axesmust be exploited.
Customer needsSites physical environment,
Possible solutions with their equipments
This document can be help to organize, present and realize good indoor RF Design.
1.1 INDOOR RF COVERAGE GUIDELINE
This document describes with more or less information the main methodology required to follow
to Design RF inside the building. It is a direct and actualized complement to UMTS indoor RF
design guidelines.
1.2 SCOPE OF THIS DOCUMENT
The scope of this document is to support RF Engineer during Indoor RF Design & deployment, In
particular on On field activities. Engineers in charge of these activities can found inside the main
activities that must be conduct and some key points to succeed it.
1.3 AUDIENCE FOR THIS DOCUMENT
This document is internal only. Its audience is all RF Designers in charge of Indoor RF Design
and deployment.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
6/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 6/74
2 GENERALITIES ABOUT INDOOR
In UMTS, Indoor coverage is an important target for operators. In fact after external coverage(macro-cells & micro-cells) the best way is to cover the main buildings specifically. Public and
private or corporate services can be deployed which can draw in strong revenue for operators.
That applies buildings as airports, main stations, high shopping centers, hotels, or strong offices
& headquarters.
But to be a success this system need to perform homogeneous coverage with high level of
quality and to dimension equipments linked to expected traffic in term of capacity and allocated
services. The deployment needs high control level due to in building constraints, public safety risk
& limitation, and co-sitting constraints with other systems
In second hand to follow the market and despite the strong in-building constraints, Design and
deployment must be realized in order to reduce implementation cost. These constraints imposegood organization and on-site activities.
2.1 INDOOR SPECIFICITIES
Indoor Design needs to take in account the indoor specificities. Indoor area is close area with
three dimensions, where walls and specific areas, as lift, limit the coverage.
Inside the building, two types of main area can be described:
Free areaas open space, atrium and Hall,Close areaas offices, corridors and passages or lift pipes.
External/internal walls and ceiling/floors necessitate particular analysis due to windows, steel and
false level using. Each structure has its proper absorption and reflecting coefficient. These
parameters limit RF propagation.
Inside building there are numerous installation constraints as cable road, installation and fixation
inside false ceiling, antenna visual impact, distance to respect for RF blocking control and public
safety.
Each building has its own propagation conditions and environment; however it is possible to
classify the main building and to generalize offered solution class by class.Due to corporate aspect, if we need to deploy indoor system, radios Designer need to implement
high level quality of communications. Actually, for good level of use indoor system must be better
than outdoor efficiency.
In case of specific private or corporate services the waves confinement is necessary. To limit
outdoor leakage specific Design must be apply on first levels.
In term of traffic, users and traffic used are not homogeneous, it is possible to find inside the
same building some hot areas with high traffic density and high capacity demand (as offices
areas) and others areas more dedicated to speech communication areas as corridors, or life area
(restaurant,).
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
7/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 7/74
On the other side, the solution proposed must take into account the deployment constraints
imposed by
the customer, and the building owner: a distribute antenna system solution is
sometimes too heavy solution
the roll out planning: indoor mass deployment solutions are many times required
price
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
8/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 8/74
2.2 INDOOR DESCRIPTION
The following scheme and pictures show the main indoor characteristics. There are not
exhaustive and other environments can be found.
Figure 1: Indoor structure Figure 2: view in construction Figure3: Final view live
Figure 4: Indoor Views
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
9/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 9/74
3 SAFETY NORMS
3.1 PRINCIPLE
Safety normalization is very complicate. The aim of this part is to provide the basic rule, to
respect the principal ones.
International safety norm
The international safety norm is ICNIRP. This is the less constraining one.
For countries where there are no specific constraints, ICNIRP values must be respected.
The values specified by ICNIRP correspond to the max power allowed for a permanent
exposition whatever the distance from Tx antenna is.
ICNIRP
Frequency range Network Type E (V/m)Power
received(dBm)
PMR 28 19,7
GSM 41,2 16
DCS 58,3 13400MHz to 2GHz
PCS 60 12,8
UMTS/DVB-SH 61 122GHz to 300GHz
LTE/ WiMAX 61 9
Figure 5: ICNIRP recommendations
Generally countries norms are more constraining than ICNIRP.
Below an example of safety norm specified by countries or group of countries:
European safety norm
For European community, there is a minimum safety norm which must be respected in all
its countries; whatever the distance from Tx antenna is.
CENELEC (European community norm)
Frequency range Network Type E (V/mPower
received(dBm)
PMR 2,8 -0,3
GSM 4 -4,3
DCS 6 -6,8400MHz to 2GHz
PCS 6 -7,2
UMTS/DVB-SH 6 -8,12GHz to 300GHz
WiMAX 2,5-3,5 6 -11
Figure 6: European community safety recommendations
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
10/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 10/74
Paris city safety norm
More constraining than European norm, cities can specify also their own safety norms.Below the values specified for Paris.
Paris city norm
Frequency range Network Type E (V/mPower
received(dBm)
PMR 2 -3,24
GSM 2 -10,3
DCS 2 -16,3400MHz to 2GHz
PCS 2 -16,8
UMTS/DVB-SH 2 -17,62GHz to 300GHz
WiMAX 2,5GHz-3,5GHz 2 -20
Figure 7: Paris safety recommendations
For all these norms, a permanent exposition is considered to the sum of all the radiation. It
means that if a GSM and UMTS network are deployed, the equipment used to verify if the safety
norm is respected, combines the both radiations.
3.2 MINIMUM DISTANCE REQUIREMENT
The aim of this part is to show the most constraining scenario between the different frequencies.
Assumptions:
Propagation conditions: free space
European norm
Frequency range Network TypeMinimum distance(meter) from Tx
antenna for max EIRP=32dBmMinimum distance( meter) from Tx
antenna for max EIRP=12dBm
PMR 2,46 0,25
GSM 1,73 0,17
DCS 1,15 0,12400MHz to 2GHz
PCS 1,15 0,12
UMTS/DVB-SH 1,15 0,122GHz to 300GHz
WiMAX 2,5GHz-3,5GHz 1,12 0,11
Paris city norm
Frequency range Network TypeMinimum distance( meter) for Tx
EIRP=32dBmMinimum distance( meter) for Tx
EIRP=12dBm
PMR 3,5 0,35
GSM 3,5 0,35
DCS 3,45 0,35400MHz to 2GHz
PCS 3,46 0,35
UMTS/DVB-SH 3,43 0,342GHz to 300GHz
WiMAX 2,5GHz-3,5GHz 3,16 0,32
Figure 8: Minimum distance required from Tx antenna specified by safety norms
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
11/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 11/74
4 OEM AND PRODUCTS SOLUTIONS
4.1 DISTRIBUTED ANTENNA SYSTEM (DAS)
In order to provide the required coverage, several antennas connected to one base station/Node
B are distributed throughout the building by means of 3 possible distribution systems:
Passive distribution
Hybrid distribution
Active distribution
4.1.1 PASSIVE DISTRIBUTION
Passive DAS, three main systems of terminations are available. Efficiency and cost are different.They use the same standard equipments to feed different types of radiating elements. Thesystems are:
DAS with antennas terminationThat necessitate some pre-studies to optimize type and orientation of antennas used.
Omni antennas:Used for large open space as atrium or to cover open space area after the first
levels.On first level it is difficult to confine wave inside the building and that can increaseindoor coverage leakage outside the building (risk of external users captures).The gain of these antennas is classically 2 dBi and it is possible to find some realmulti-bands antennas.
Directive antennas:Used to apply specific coverage or to limit the indoor coverage leakageFor a directive aperture of 70 to 90 in vertical and horizontal the gain is around 6to 8 dBi.
DAS with leaky feeder and load termination
Radiating cable is the best solution for indoor coverage in particular in confined or difficultto access area.It can radiate homogeneously and be installed everywhere due to its suppleness. Due toceiling/floor mask, radiating cable must be used floor by floor. This solution is interestingin particular when the network is private or corporate and the service is selective and withcharge for admission.Externally, it is as RF cable and ensures its function of feeding. But by its constitution itcan also ensure coupling with the mobile. Specifics holes or slot are realized on the outerconductor of coaxial cable to ensure the radiating function.
For good efficiency the radiating cable needs specific installation. The minimum distance
between cable and obstacle as wall is around five centimeters. It is possible to use it
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
12/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 12/74
under false ceiling but if the false ceiling is metallic, due to mask effect, leaky cable isunworkable.
DAS with mixed termination
Through distributive antennas concept it is possible to use radiating cable. Use of thisequipment is similar to standard cable.
Due to indoor constraints it is interesting to complete the radiating cable coverage withantennas as some areas could not be well covered if only one method is used.
Completing the radiation system used, the power attenuation through the tapers, couplers,
or other passive elements must be well managed in order to have a sufficient radiated
power which ensure a sufficient coverage.
Completing the radiation system used, the power attenuation through the tapers, couplers, or
other passive elements must be well managed in order to have a sufficient radiated power which
ensure a sufficient coverage.
The main elements used are the following ones.
Combiners are used to combine different output of the Node B in the same band or
several operators.
Directional couplers are used to split the power unequally in two branches.
Diplexers are used to combine signal from different bands (GSM/UMTS) or (DCS/UMTS).
Triplexers can also be used in case the system has to support GSM, DCS and UMTS.
Splitter (to distribute the power)
Loads
Coaxial cables
Figure 9: passive distribution systems
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
13/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 13/74
Advantages of passive distribution
All the equipments used are most generally broadband equipments. As indoor DAS are deployedfor high frequency bands existing DAS which supports GSM have been deployed in 1800MHz
band, and antenna installed support also UMTS band. Then in case of existing 2G indoor
systems with sufficient coverage, the same infrastructure of cables, antennas and splitters can be
used for the 3G indoor system with only addition of diplexer at the output of BTS and Node B.
Low cost equipments compared to any active system.
Limitations of passive distribution
Installation is quite difficult and costly especially for high buildings, also the existence of
important installation constraints (for example: acceptance of the building owner).
Increased number of antennas leads to more cable + splitter losses, and hence low EIRP at
each antenna. For high building or buildings requiring high number of antennas, these losses
are quite high. In this case, the choice of another distribution system (active or semi active)
becomes mandatory.
4.1.2 ACTIVE
A distribution is considered Hybrid when it includes a combination of active and passive systemand when the antenna system is passive.
The two main systems used for hybrid distribution are:
Bi-directional amplifier
In-building fiber optic and/or electrical extension
They are detailed in the following parts
4.1.2.1 BI-DIRECTIONAL AMPLIFIERS (BDA)
Bi-directional amplifiers are used in order to compensate the cable and coupling losses when the
passive distribution alone cannot provide enough coverage.
The main drawback of this system is: chaining amplifiers induces the noise figure of the system
increase.
The following equation shows the total noise figure calculation of a BDA chain:
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
14/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 14/74
Figure 10: Schema of TX/RX chain with BDA
.....])3()2()1(
14
)2()1(
13
1
121log[10)( +
+
+
+=
gxgxg
f
gxg
f
g
ffxtotalNF
With
f the noise figure for both the amplifiers and for the cables linking the cascaded
amplifiers
g the gain of both of them
4.1.2.2 IN BUILDING FIBER OPTIC AND/OR ELECTRICAL EXTENSION
Two types of system link are generally used.
Fiber optic
Electrical cable
Fiber optic system is used to cover big areas in order to minimize losses.
Electrical system is used in order to facilitate the installation.
These two systems are detailed in the parts below.
4.1.2.2.1 FIBER OPTIC SYSTEM
The system consists of two main units, the master unit and the remote unit.
The master unit is the unit connected to the Node B, RRH or repeater. It converts the RF signal in
optical one. A master unit supports up to 16 remote units.
The remote unit is generally connected close to the antenna, or a passive distributed antenna
system. It receives the optic signal and converts it in RF one.
Figure 11: Schema of Optical fibber system usage
Coaxial cable &
Passive systemFiber Extension
Master Unit
Node B
Remote Unit
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
15/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 15/74
The optical extension, allows covering a building with a Node B based in another building, or
covering the upper floors of a tower while the Node B is located in its basement.
The output power depends on the used band as well as on the number of carriers.
The table below shows the maximum carrier level based on available IP3 level and maximum
tolerated spurious emission of -13/-30/-36 dBm.
IP3 level 54 dBm 50 dBm 44 dBm 40 dBm 27 dBm
# of carriers
2 32/26/24 dBm 29/23/21 dBm 25/19/17 dBm 22/16/14 dBm 14/8/6 dBm
4 29/23/21 dBm 26/20/18 dBm 22/16/14 dBm 19/13/11 dBm 11/5/3 dBm8 26/20/18 dBm 23/17/15 dBm 19/13/11 dBm 16/10/8 dBm 8/2/0 dBm
16 24/18/16 dBm 21/15/13 dBm 17/11/9 dBm 14/8/6 dBm 6/0/-2 dBm
Max. carrier level (dBm) based on IP3 level and max. spurious emmission of -13/-30/-36 dBm
Figure 12: IP3 level and max spurious emission supported
4.1.2.2.2 ELECTRICAL SYSTEM
It is composed of two types of components: a Hub that connects via Cat-5 to up to eight Remote
Access Units (RAUs).
The Hub receives its radio frequency (RF) signal from a Node B or a repeater. The Hub
electrically distributes the signal to the RAUs via twisted pair cabling.
Each RAU is connected to antenna and ensures conversions from electrical signal to RF signal,
and from RF signal to electrical signal.
Figure 13: Electrical system DAS
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
16/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 16/74
It is used for small to medium buildings such as office buildings, regional distribution facilities and
small conference centers.
The main limitation of this system is due to the cable distance between Hub and RAU should not
exceed 100 meters.
4.1.2.2.3 EXAMPLE OF EXISTING SYSTEM: UNISON SYSTEMFROM LGCWIRELESS
System Architecture
The Unison system is composed of the following main components:
Main HubExpansion Hub
Remote Access Unit (RAU)
Main Hub:
The Main Hub is the primary block in the Unison system and functions as the interface between
the Node B or repeater and the indoor network. It receives the RF signal and distributes it to the
expansion hubs through optical fiber medium.
The optical link between the Main and Expansion Hubs can reach up to 6 Km by using single
mode fiber.
Each Main Hub supports up to 4 Expansion Hubs. For larger indoor designs, several main hubs
may be required.
Expansion Hub:
The Expansion Hub is the intermediate unit between the Main Hub and the Remote Access Unit
(RAU). It converts the received optical into electrical signal which is transmitted to the RAU over
standard CAT 5 twisted pair cables (ScTP).
The distance between the Expansion Hub and RAUs is limited to the recommended 100 meters,
after which signal quality would be affected. Each Expansion Hub can support up to 8 RAUs.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
17/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 17/74
Remote Access Unit (RAU): The Remote Access unit is Located closest to the radiating point.
It converts the electric signal from the expansion hub into RF and feeds it to the antenna, and
reverse.
Figure 14: Unison system architecture
The Unison system is mono band system.
The frequency range of UMTS Unison system is 35 MHz. In case of several operators, they must
be operating with 35 MHz bandwidth; otherwise at least two Unison systems will be installed.
The cost of active equipment is high comparative to passive system.
4.2 REPEATER
Two main types of repeaters are available:
RF repeater and the Optical Fibber repeater
4.2.1 RF REPEATERS SOLUTION
Classical RF Repeater is bi-directional amplifier with advanced function as AGC (automatic gaincontrol) and special filtering function.It reduces path loss between BTS (particular cell called donor) and terminal element (radiatingcable or antennas). It is used when coverage is decisive.
The main uses are:Increase coverage for specific area, (tunnel or specific hot spot in limit or outside the cellcoverage)Holes elimination,Indoor capture & distribution to transfer to donor BTS (Cell that cover the building area)
This repeater type is composed of two antennas:
Donor Antenna between the repeater and the Node-B: Highly directive antenna
Serving Antenna between the users and the repeater
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
18/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 18/74
It amplifies the signal both in the UL and in the DL independently or equally depending on the
repeater type.
The amplification concerns useful signal and all type of interferences
Figure 15: Repeater description
The main characteristics are:
Frequency band: single or multi-band, wide or narrow band
Frequency range (divides in uplink and downlink)
Number of channel: up to 3 carrier
UL gain: tunable by users ( one gain per carrier, for multi-carrier cases)
DL gain: tunable by users ( one gain per carrier, for multi-carrier cases) AGC value AGD (absolute group delay),
Inter-modulation level,
Global noise figure.
4.2.2 OPTICAL REPEATERS
Fiber optical repeater is a repeater conceived to transport useful information on long distance. Ituses characteristics of optical fiber. But it needs to convert RF energy to compatible opticalenergy/. This type of repeater is really expensive and must be used only for very long tunnels orhigh and large indoor coverage necessity.
If the concept is the same it is possible to find two main architectures.The first apply cable and close antennas (As Incell from Andrew) for punctual radiating point: inbuilding usingThe second apply remote unit including transceiver and power amplifier (for distribution) tunnel orDAS in building.
Constitution:
Optical repeater is composed of several boxes. The main box called main hub, master unit orcentral distribution unit is fed by BTS directly through RF cable or by antenna (donor antenna).
Terminal unit called remote unit (RU) for amplified unit or Remote antenna unit (RAU) for lowpower unit (as Andrew InCell) can apply distributed system or only one antenna.
Repeater
Connector A Connector B
Repeater
Connector A Connector B
BAND
CHANNEL
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
19/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 19/74
Transceiver system is including in these box that cans convert RF to Optical carriers or optical toRF carrier. Depending on carried available frequency bandwidth it is possible or not to transportwide W-CDMA. This transceiver uses laser and thats why the cost is high.
These systems are managed and alarm controlled by management software.
Figure 16: Optical repeater principle (1)
Two concept of optical fiber repeater system can be used. Depending on the choice, the pricecan be modified (in general due to laser use the equipment price is high Opex (Capex) price isfunction of terminal concept used).
System presentation:
Optical repeater with remote unit powered.
Figure 17: Optical repeater principle (2)
Optical Repeater with frequency band sharing:
Fiber Link
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
20/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 20/74
Figure 18: Optical repeater with frequency band sharing
About optical repeater installation:
If optical fiber is easy to install due to its feeble dimension and its high suppleness, dont forget tocontrol optical connections. Optical Connectors are fragile and they are really the hard point ofoptical installation.Often it is possible to use existing optical fiber in particular if the building is new building (Refer tothe survey).In general, Optical equipment as MCU or RU needs soft installation (laser adjustment).
4.3 INDOOR SMALL CELL-CELL NODE-B
Small cells are auto-configurable products including a sniffer module, which allows analyzing
macro network RSCP at small cell position, and then deduce the max Tx power allowed in order
not to disturb macro network.
Main part of information when the call has been established is deduced from UE
measurements.
Two small cell versions are available today:
Home cell:
o Max power: 13dBm (20mW)
Enterprise cell:
o Max power: 20dBm (100mW)
4.3.1 NOISE FIGURE
The typical noise figure is 10.5 dB.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
21/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 21/74
5 RADIO DESIGN METHODOLOGY
5.1 PRINCIPLE & CONSTRAINTS
Indoor Design is complex to realize. It needs to take in account the third dimension. Volumereplaces traditional surface to cover. Indoor specificities are important and can modify RF design;the main ones are detailed below:
The design contributors:Different contributors intervene during the Design phase. Thecustomers are operators but building owner intervenes for installation constraints, visualimpact limitation or public safety.
Installation constraints: Indoor is not an open area many structures can limit or block
the waves passing.Visual impact and public safety can limit too the design.
Radio propagation: In addition to walls and structures limitation, wave need to beconfined inside the building area and external leakages must but limited.
Co-sitting constraints: A new network must be implemented taking into account theexisting networks deployed. Interference must be well managed.
Indoor dimensioning Services:New technologies can introduce new services or specificservices as corporate networks, data transmission or internet mobile. This plays a role onDesign and needs to improve coverage quality and traffic capacity.
Through these constraints and based on experiment results and building surveys, on one handand on RF Process on the other hand the following item must be realized during the Designphase:
Design constraints identification (co-sitting effect, forbidden area, traffic concentration,)
Traffic model qualification,
Technical choice (equipments, solutions, dimensioning)
Impact on cells performances and traffic capacity,
Deployment strategy and associated cost study,
Solutions and associated link budget,
Results presentation for customer agreement,
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
22/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 22/74
5.2 DIMENSIONING SERVICE & TRAFFIC ASSUMPTIONS
The process of the design is based on the coverage requirements of the worst link budget
between UL and DL.This depends on the product solution selected.
Dimensioning must be done to support
DL PS384 service at cell edge
400kbps HSDPA throughput at cell edge when surrounded cells have 75% traffic load
PS64 and/or CS64 at cell edge with 75% UL load.
75% UL load is the recommendation for new indoor network deployed.
For existing indoor network designed with 50% UL load, the design is not changed, but UL
load increase due to HSUPA introduction must be considered (see 6.5.3.3.1).
The available path loss has been calculated in the LB with the parameter settings validated with
the customer.
TRAFFIC ASSUMPTIONS
Below the service and traffic information necessary to complete an UMTS design are presented.
Traffic assumption has a large impact on the cell count and radio planning results. They should
thus be detailed for each of the required services.
The traffic assumptions can be defined by different ways:
A % of traffic load is specified:
o 75% of traffic load including common channels and shared power are
usually considered according to the customer this value can change.
Mixed traffic provided by the customer:
o This mixed traffic is based on a user call profile which contains each
service activity and their duration or data volume transmitted during a busy
hour. First it is necessary to determine exhaustively all the services the
network will have to support. A service is the conjunction of a data type(voice or data), a transport mode (circuit switched or packet switched), and
a data rate.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
23/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 23/74
The services which can commonly be met on projects are the following:
Conversational Speech 12.2CS64
PS64
PS128
PS384
HSDPA
HSUPA
For each building; traffic is defined per service.
5.3 LB ANALYSIS
5.3.1 ENGINEERING MARGINS
5.3.1.1 SHADOW MARGIN CALCULATION FOR QOC
Alcatel-Lucent Networks considers in indoor only the log normal fading of the indoor propagation,
and power control variation due to fast fading effect.
Then, according to statistical laws, a global standard deviation is calculated which characterizes
the whole propagation channel:
With
indoor : STD for indoor shadowing
5.3.1.2 DAS LOSSES
This parameter is applied only for indoor solutions which include distributed antenna system, not
for stand alone solutions.
Distribution system losses are also considered, losses of cables, splitters, and combiners.
Average losses value is obtained while calculating the EIRP of each antenna in the building.
The standard value considered for passive DAS loss per floor is 25dB.
This value must be updated, during the roll out phase when the real attenuation values are
known.
indoorTot =
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
24/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 24/74
For active DAS loss, there is no default values, UL DAS loss and DL DAS loss must be specified
separately as some UL & DL gain can be tuned independently with optical fibber products.
5.3.1.3 OBSTACLES LOSSES
The different obstacles loss values are detailed in the table below,
Figure 19: Indoor obstacles loss @2100MHz
5.3.2 UPLINK PARAMETERS
The table hereafter presents main UL parameters.
Uplink load with R99 only (withHSUPA)
50% (75%)
Modeling Channel for C/I performance Pedestrian A
Mobile power (HSPA) 21dBm(24dBm)
Mobile speed 3 km/h
Coverage type Deep indoor
% of QoC for area reliability(equivalence in cell edge reliability)
95% (86%)
Figure 20: Environment global parameters
5.3.3 DOWNLINK BUDGET
UMTS downlink budgets are always built the same way. In fact there are two downlink budgets,
first one deal with pilot dimensioning and second one with service dimensioning.
The pilot dimensioning phase allows as well fixing common channels contribution as their power
is relative to pilot one.
Obstacle Penetration Loss [dB]
UMTS Frequency Band:1700, 1900, 2100MHz
External concrete wall 15
Inside wall 5 to 10
Window 3
Door 5
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
25/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 25/74
CPICH power calculation
The aim is to determine the minimum CPICH power ratio to insure a certain pilot quality at celledge. The max allowable path loss is fixed by the uplink budget and usually based on the
dimensioning service. Pilot quality is estimated by the ratio of energy chip over interference Ec/Io.
The recommended CPICH power ratio is between 8% and 12% with a default value equal to
10%:
8% for Dense urban, urban and some suburban areas which are interference limited
12% Suburban and rural zones essentially noise limited
These values have been deduced considering
Pilot Ec/Io target = -15dB in full traffic load conditions.
Under such value; mobile pilot detection is problematic.
Extra-cell interference has been evaluated to DL Ie/Ii= 200% compared to intra-cell, considering
two neighboring macro-cells received with the same RSCP than the serving cell
pilot ratio is the same for the serving cell and the two neighbors
serving cells and the two neighbors have the same traffic load
In order to estimate the Io value at cell edge, in addition of the path loss, the following
inputs are required:
Mobile noise figure and antenna gain are used to determine the noise floor
Common Channels power setting
Common channels are always fixed relatively to pilot power.
The table below contains common channel power settings recommended.
Common Channels Power Distribution
DL Ie/Ii Target for AR=90% 200%
CPICH Ec/I0Target [dB] -15.0 dB
CPICH Power Ratio [%] Between 8% and 12%
Power rel. to CPICH
[dB] Time multiplexed
P-CPICH 100% of time
P-SCH -5.0 dB ----
S-SCH -5.0 dB ----
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
26/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 26/74
P-CCPCH -2.0 dB 100% of time
S-CCPCH -1.0 dB 30% of time
PICH -5.0 dB 100% of time
AICH -7.0 dB 100% of time
Common Control Channels Power Ratio [%] 22%
Shared Power reserved for R'99 Traffic [%] 10.00%
Figure 21: Common channels power settings
As mentioned in the table above the recommended % of CPICH power ratio is 8% to 12%.
8% for Dense urban, urban and some suburban areas which are interference limited
12% Suburban and rural zones essentially noise limited
Some of ALU customers have different recommendations and can use 5% CPICH power ratio, in thatcase ALU will use these recommendations, but the Ec/Io target should change too.
For instance with 5% CPICH power ratio the Ec /Io target value for 80% network traffic loadshould be -18dB instead of -15dB with ALU recommended power settings
Other parameters
2100MHzThermal Noise (3,84 MHz) -108 dBm
MS noise figure 8 dB
MS antenna gain 0 dBi
Interference factor @ cell edge 2 (Ie=2*Ii)
CPICH Ec/Io target -15 dB
Orthogonality factor(0 no orthogonality) 0.06 in indoor(@3km/h
Figure 22: DL budget parameter
5.4 RF DESIGN TARGETS
Based on dimensioning service and traffic assumptions, the RF design can be completed and
optimized.
The first step is then to select the correct candidate sites in order to fulfill the required QoC and
QoS per area.
During the design, it is important to keep in mind that a W-CDMA network is an interference
limited system, and that in such cases, the sites should be positioned so as to limit inter site
interference.
In order to ensure a good network, the following criteria must be completed.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
27/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 27/74
5.4.1 MINIMUM ATTENUATION REQUIRED AND TOTAL EIRP RECOMMENDED
In order to be sure that we respect the safety limit everywhere, one of our constraints is to ensure
a minimum attenuation between the power amplifier and the antenna connector, in order toachieve a 10dBm total power EIRP per antenna.
10dBm total power EIRP answer to two constraints, first one is safety limit as with such EIRP one
of the most constraining values is respected after 1 m distance from the antenna.
The second constraint is 10dBm total power EIRP per antenna induces to have at least 20dB
attenuation between RRH and Node-B cabinet and antenna connector, as minimum power which
can be radiated by RRH is 27dBm.
5.4.2 COVERAGE TARGET
The different design targets are the following ones:
5.4.2.1 SHARED CARRIER CONFIGURATION
Themain aspect here is to manage correctly the interference with outdoor network.
The indoor network is deployed where an outdoor one already exist, so the main rule is to not
decrease existing outdoor network quality and capacity with an interference increase on the
outdoor areas.
Indoor dedicated Node-B can not be deployed without distributed antenna system solution.
This latest one required a heavy and long deployment, as cables must be positioned inside false
ceiling; even for hybrid fiber optic DAS cables between RAU and antenna are required.
Based on outdoor measurements, and indoor penetration measurement, the outdoor cells RSCP
on each side of the building are well known; also the outdoor macro-cells RSCP values in front of
windows inside the buildings.
With such information, completed by floor plan and indoor measurements, the antenna
positioning can be done in order to have on ground floor and first floor; indoor cell best server
inside the building; and outdoor cells best server outside the building.
The RF criteria to support such recommendation are the following ones:
3rdfloor and highest
Requirements are:
Guarantee a good coverage and capacity over the building floor.
Guarantee an enough signal strength to ensure
Indoor cell CIPCH RSCP = Outdoor macro cell CPICH RSCP+3dB
everywhere over the area which should be covered
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
28/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 28/74
2nd, 1st & ground floors,
Two outdoor coverage cases must be considered
Case1: Hole of coverage or poor coverage of the existing outdoor network
Macro-cell RSCP-95dBm
No specific problems as indoor cells can cover part of the street in order to ensure
better quality than outdoor network
RSCP target depends on the following criteria
Indoor RSCP must be equals to -98dBm at 10m outside the building,
CPICH power ratio is considered around 10%
Case2: Good Outdoor coverageOutdoor Macro-cell RSCP >-80dBm
The macro-cell outdoor network should not be disturbed by indoor cells
implementation
Indoor cell CPICH RSCP must be set in order to ensure that
Indoor cell CIPCH RSCP = Outdoor macro cell CPICH RSCP +/- 2dB in
front of the windows, store, building entrance, shopping mall entrance.
With such criteria, interferences between indoor cells and Macro cells are not too
high
RF recommendations for distance between antenna and nearest window
Assumptions
Standard indoor propagation area obstacles between 1m to 1,8m height
Outdoor macro-cell RSCP: -80dBm
Aim: to be best server in indoor and no to interfere outdoor network outside the building
CPICH EIRP with 10% CPICH powerratio
-10dBm 0dBm 10dBm
Distance from the nearest windowand/or entrance
5m 20m 30m
Distance from the nearest external wall 0m 0m 5m
Figure 23: Minimum distance required for Indoor small cell
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
29/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 29/74
5.4.2.2 DEDICATED CARRIER CONFIGURATION
Compare to the shared carrier solution, there is no more neighboring and interference impact on
outdoor network.
Anyway in order not to support over a too long distance indoor to outdoor users, it is
recommended to realize the indoor design in order to support an indoor RSCP level equals to
-95dBm at 20m outside the building .
5.4.3 INTERFERENCE CRITERIA
5.4.3.1 EC/I0 TARGETS
The Ec/Io target value depends on the traffic load and the level of extra-cell interference. The
values detailed below considers CPICH power ratio between 8% to 12%; if CPICH ratio is out of
this range then Ec/Io target should be modified in consequence (5% CPICH ratio induce a 3dB
decrease on the target values detailed below)
When Ie/Ii = 200%
o 95% of the design area should have a Ec/I0 value higher than the
target (-15dB), with 90% DL load
o 95% of the design area should have a Ec/I0 value higher than the
target (-14dB), with 75% DL load
When Ie/Ii = 100%
o 95% of the design area should have a Ec/I0 value higher than the
target (-13dB), with 90% DL load
o 95% of the design area should have a Ec/I0 value higher than the
target (-12dB), with 75% DL load
Such Ec/Io criteria allow managing interferences in order to obtain a RF network design able to
support
PS384 service at cell edge when surrounded cells have 50% traffic load or
PS128 at cell edge when surrounded cells have 75% traffic load.
400kbps HSDPA throughput at cell edge when surrounded cells have 75%
traffic load
400kbps HSUPA throughput at cell edge with UE category 12.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
30/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 30/74
5.4.3.2 POLLUTED AREA & OVERLAP ANALYSIS
This part concerns indoor design done with micro-cells or pico-cells, as the number of
cells is more important than when indoor design is done macro-Node-B
Polluted area criterion:
Done to evaluate the number of scrambling in a 6dB interval from the best server
The number of scrambling code should not exceed 3, and the % of covered area
with 3 scrambling code should be lower than 5%.
High signal level overlap criterion:
It consists in increasing the design threshold 10dB, and based on this design
threshold to analyze the number of server.
In this analysis, the % of 2 servers in the design area should not exceed 15%.
The optimization method to reach these targets is detailed in the part below.
5.4.4 NEIGHBORING PLAN / SCRAMBLING CODE PLAN
This can be a critical aspect of indoor network deployment.
Currently Alcatel-Lucent RNC supports
32 intra-frequency neighbors declared
32 inter-frequency neighbors declared
Intra-cells neighbors + inter-cells neighbors 48 ( 64 in UA6.0)
The radio criterion for neighbor and scrambling code plans is:
Considering two cells cell A and cell B, on the same frequency carrier using the same cell ID, the
distance between those must satisfy the following criteria:
RSCP
At cell A edge (RSCPcellA -95dBm):RSCPcellA RSCPcellB+ 10dB
At cell B edge (RSCPcellB -95dBm): RSCPcellB RSCPcellA+ 10dBThe field feedback from existing outdoor networks is:
Around 20 intra-frequency neighbors are declared
The number of inter-frequency neighbors declared depends on the operator
approach. Currently only co-localized cell is declared, but it can go up to the same
number of intra-frequency neighbors declared.
Based on such analysis, the outdoor network neighboring plan must be carefully analyzed in
order to see the added number of neighboring cells which can be declared.
Considering that only the ground floor indoor cells are declared as neighbors for outdoor cells;
the limit of neighbors declared will be reached if there are more than 12 indoor networks buildings
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
31/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 31/74
deployed in the same cell, even if just one scrambling code is considered to cover the ground
floor.
5.5 OPTIMIZATION
5.5.1 METHODOLOGY
The main interference aspect which should be correctly managed is between outdoor network
and indoor network.
To reduce interferences, two major tuning can be done:
Azimuth optimization
Max power reduction or CPICH increase.
Electrical tilts are not available for indoor antennas.
These methods are identical in all radio system in order to limit inter cell interference, or to
improve the QOC.
Based on these information, and with some KPI targets values like
RSCP level,
QOS target
Ec/I0 target,
GOS target,
Pollution window,
Active set size,
5.5.2 OPTIMIZATION PHASES
The optimization phase is done simultaneously or just after the coverage study.
The aim is done to reach and improve all the RF design targets defined in the previous part.
This optimization phase contains several steps:
5.5.2.1 OPTIMIZATION AND VALIDATION BASED ON RF FIELD ANALYSIS
This part describes the field measurement process used to finalize and validate the RF
parameters in order to obtain the best network performances.
A test measurement campaign using
RF measurement scanners for step 0 to step 2
test mobiles, is done for the other optimization steps.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
32/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 32/74
The services analyzed are voice, visio 64kbps for CS services, and 384kbps and HSDPA for PS
services.
Step 0:
Following the site report, the installation will be performed.
If any modification in cable path or length is implemented, the installation team should
inform the radio design team.
Before the Node B commissioning and once the installation is totally finished, validation of
installation of the antenna system. This will include:
Loss measurement generated by splitters and coaxial cable distribution.
These tests mainly consist of measuring the received power at each antenna
connector.
The visual inspections of the splitter connection to avoid any cross cabling.
Hereafter is presented a brief description of the measurement process:
In place of the Node B, a transmitter is installed, providing a precise and
known power to the whole installation.
At each antenna connector, an appropriate power meter with the required
sensitivity is to be used.
Step1:
Done to verify and validate the pre-optimization efficiency compare to the results obtained
in step 0. Based on these measurements, the aim is also to correct some radio
parameters in order to improve the coverage and radio quality, and to identify some
neighboring problems which required an update of the neighboring plan.
Step 2:
Validation of the radio optimization
Ec/Io values reached the target ones
QoC corresponds to the target one
Neighboring plan is the best one
Step 3 and others
Done to optimize UTRAN parameters in order to maximize the CS and PS performances
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
33/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 33/74
5.6 UMTS VS OTHER TECHNOLOGIES INDOOR NETWORKCOEXISTENCE
5.6.1 SEPARATED FREQUENCY BAND
As for outdoor, an indoor UMTS network deployed must not interfere or be interfered by existing
GSM network.
Depending on product performances; isolation is required.
The isolation recommended by ALU is based on a maximum of 0,5dB sensitivity degradation; or
a maximum of 5% capacity decrease.
.
Warning!
Some configurations are very difficult to manage, and it is quite impossible to have
a not degraded network.
It occurs when UL band of one technology is adjacent to the DL band of the other
one.
The main configurations are the following ones:
Co-existence between GSM850 or CDMA 850 with UMTS900
Co-existence between GSM1900 or CDMA 1900 with UMTS2100
Do not forget to verify, the following aspects before deployment
Radiating element frequency bandwidth
Cable or DAS frequency bandwidth
Dimension correctly the diplexer used to couple the two systems. Check particularly
the rejection level from one frequency band to the other.
5.6.2 UMTS SHARED SAME FREQUENCY BAND WITH CDMA /UMTS/GSM
When UMTS is implemented on the same frequency band than GSM or CDMA the isolation rulesdetailed below must be respected.
In order to avoid sensitivity degradation due to interference created by one of the following cases:
DL interference from UMTS Node-B to CDMA (GSM) UE
UL interference from CDMA (GSM) UE to UMTS Node-B
DL interference from CDMA (GSM) BTS to UMTS UE
UL interference from UMTS UE to CDMA (GSM) BTS
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
34/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 34/74
5.6.2.1 UMTS & GSM
Figure 24: Frequency spacing rule between an UMTS carrier and
TDMA band
For both case analyzed below the degradation target is to have a sensitivity degradation
less than 0,5dB or a capacity loss lower than 5%.
Recommendations below have been done considering hopping TCH as GSM adjacent
channels of UMTS900 band.
Below two cases are analyzed case where GSM and UMTS are co-localized on a same site and
case where they are not and so the worst configuration then is when GSM cell edge is close to
UMTS site
We have now two types of filters in our product,
Standard filter whose attenuation starts at 2.2MHz offset from center frequency
which provides an attenuation higher than 50dB after 2.4MHz frequency offset
from center frequency
Reduced filter whose attenuation starts at 2.0MHz offset from frequency band
center and provides more than 50dB attenuation after 2.2MHz frequency offset
from frequency band center. The impact reduced filter in DL is negligible
None co-located case:
Standard filter
ALU recommendation is to have 2,6MHz frequency offset
This implies that 5MHz must be free in upper or lower edge of the operator GSM
frequency band.
Reduced filter
ALU recommendation is to have 2,4MHz frequency offset
This implies that 4.6MHz must be free in upper or lower edge of the operator GSM
frequency band.
Co-located case:
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
35/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 35/74
Standard filter used in NodeB
Frequency hopping is done over less than 10 frequencies
ALU recommendation is to have 2,4MHz frequency offsetThis implies that 4.6MHz must be free in the GSM frequency band on the
area where UMTS is deployed.
For the surrounded area of UMTS900/GSM900 cluster where only
GSM900 is deployed, a 2.2MHz frequency offset is sufficient; this induces
to free 4.2MHz.
GSM uses all 900MHz
band
Figure 25: Illustration of the buffer zone
Frequency hopping is done over more than 10 frequencies
ALU recommendation is to have 2,2MHz frequency offset
This implies that 4.2MHz must be free in upper or lower edge of the
operator GSM frequency band.
Reduced filter used in NodeB
ALU recommendation is to have 2,2MHz frequency offset without any frequency
hopping constraint
This implies that 4.2MHz must be free in the GSM frequency band on the area
where UMTS is deployed.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
36/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 36/74
In order to avoid interferences between GSM900 area where all operator 900MHz band is used
and UMTS900 cluster, it is necessary to have a dead zone around UMTS900 cluster where only
channels which respect the previous recommendations are used.
This dead zone is not homogeneous because generally environment is not homogeneous, assites can be positioned on a small mountain, so they have more coverage impact than those in
city center.
For this reason the rule to respect to define sites where all 900MHz band of an operator can be
used without impact UMTS900 cluster is the following one:
Lets consider cell A as a UMTS900 cell of a UMTS 900MHz cluster, and cell B a GSM900 cell to
re-use channels inside UMTS900 band. BCCH cell B must respect
For RSCPcellA -100dBm: DL Rxlev_cellBRSCPcellA-10dB
5.6.2.2 UMTS & CDMA
3.385MHz frequency spacing should be respected between UMTS and CDMA frequency band
3.385MHz
270kHz
Figure 26: Frequency spacing rule between an UMTS carrier and a CDMA carrier
5.6.2.3 UMTS & UMTS
5MHz frequency spacing should be respected between two UMTS frequency band
Figure 27: Frequency spacing rule between two UMTS carriers
The following curves have been established considering the Tx filter and Rx filter of ALU product.
They show the capacity loss vs. the frequency offset between two adjacent UMTS frequency
bands.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
37/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 37/74
Figure 28: UMTS capacity vs. adjacent UMTS interferer spacing (MHz) for co-located case (doted line) and
not co-located
5.7 HSXPA DESIGN CONTRAINTS AND DEPLOYMENT STRATEGY
5.7.1 HSDPA
5.7.1.1 UL IMPACT ON R99 EB/NO
HSDPA introduces new common channels HS-DPCCH in UL and HS-SCCH in DL. The Eb/No
loss values calculated for each UL R99 service are the following ones. These losses must beadded UL Eb/No values for only HSDPA users in the cell and not all the cell users.
Figure 29: HS-DPCCH impact on UL iCEM Eb/No
Eb/No loss (dB)
PS64 1.9
PS128 1
PS384 0.4
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
38/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 38/74
Figure 30: HS-DPCCH impact on UL xCEM Eb/No
5.7.1.2 DL HS-SCCH
HS-SCCH is power controlled. In the LB, it is calculated, based on an iterative process using the
table below.
CQI Power relative to CPICH Power (dB)
1 7 0
8 9 -3
10 12 -5
13 30 -8
Figure 31: HS-SCCH Power Control
After many simulations, the HS-SCCH Ec/No target value which provides realistic results in term
of cell throughput, throughput distribution, and area where HSDPA is supported is the following
one.
Ec/Nt= -13dB
5.7.1.3 HSUPA DL COMMON CHANNELS IMPACT
The general approach is to assign a lower priority to HSUPA service than to the R99 ones.
HSUPA is only available on carriers where HSDPA is supported.
HSUPA introduces new channels
E-DPCCH in UL,
UL dedicated traffic channel: E-DPDCH
E-AGCH (Absolute Grant Channel), E-HICH (HARQ Indicator Channel) and E-RGCH
(Relative Grant Channel) in DL
This part analyzes the impact of these channels and the throughput calculation method
1 E-AGCH is enough for early deployment. In case there are two users, 2 TTI will be necessary
to grant both users.
1 E-RGCH is enough (up 15 signatures). The E-RGCH power is negligible, it carries one bit.
Eb/No loss (dB)
PS64 0.9
PS128 0.5
PS384 0.3
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
39/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 39/74
The activity factor of the E-AGCH should be low in early E-DCH deployment. The E-AGCH is not
transmitted all the time (as for the HS-SCCH). Once the user is granted, E-AGCH is not
transmitted again.
A fix power is reserve at the RNC level for DL E-DCH channels. This power is preempted fromHSDPA max power and is taken into account in the R99 RNC CAC.
Power rel. to CPICH [dB]
E-AGCH -2.5 dB
E-HICH -8.0 dB
Figure 32: HSUPA DL power settings
The maximum HSDPA power signaled to the Node-B will be reduced.
The R99 CAC will reject R99 calls earlier than before in case of highly loaded cell.
2100MHz Node-B 45W PA
30 m cable + 0.4dB jumper
Speech CS 64 PS 64 PS 128 PS 384
Without HSUPA DL CCH impact 273kbps 565.8kbps 604.9kbps 681.5kbps 840.4kbps
With HSUPA DL CCH impact 246.7kbps 511.2kbps 546.4kbps 615.6kbps 759.1kbps
DL capacity decrease due to HSUPA -9.6% -9.6% -9.6% -9.6% -9.6%
Figure 33: DL capacity loss due to HSUPA
9.6% capacity is a worst case, as it takes into account cells full loaded all the time. Around 5%
capacity loss can be expected, in standard case.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
40/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 40/74
6 ANALYSIS OF EACH RF INDOOR SOLUTIONS
6.1 NATURAL INDOOR PENETRATION
6.1.1 DESCRIPTION
This is the natural outdoor to indoor penetration. It must be taken into account during the outdoor
macro-cell network roll out phase.
The indoor penetration considered has a direct impact on the number of sites required to cover
an area, so the number of cells, tilts, azimuth
The Alcatel-lucent recommendation is to consider the following indoor penetration losses:
Figure 34: outdoor to indoor penetration loss
These values allow supporting UL dimensioning service until indoor daylight environment. It
corresponds to indoor areas far from window (>10m) with potentially some obstacles (like
cupboards) between UE and window, but no wall.
Anyway to have a good indoor penetration which means ensuring coverage in major part of deep
indoor areas, these values must be increased by 3dB.
Environment Penetration Loss [dB]
UMTS Frequency Band:1700, 1900, 2100MHz
Dense Urban 20
Urban 17
Suburban 14
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
41/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 41/74
6.1.2 ADVANTAGES & DRAWBACKS
Advantages:
No indoor network to deploy
Less expensive than deploying outdoor network+indoor network
Drawbacks:
Must be anticipated since the beginning of the outdoor network deployment
Can not be updated after deployment without impacting all the network optimization
6.2 MASSIVE PUBLIC NETWORK INDOOR DEPLOYMENT
It concerns a massive roll out phase with extremely short delay requirement, like 2 days to deploy
an indoor network inside a ten floors building. This type of requirement can not be supported with
DAS, as it takes too many times for deployment. The indoor products use is essentially indoor
small cell.
6.2.1 INTERFERENCE ANALYSIS IN SHARED CARRIER CONFIGURATION
6.2.1.1 BEST SERVER BETWEEN INDOOR SMALL CELL VS MACRO-CELL
For all the remarks done in the parts below, it has been considered that Indoor small cell is able
to evaluate correctly the different SC used and the RSCP received of all its neighbors, whatever
the measurement method used
Measurement perform by indoor small cell
UE measurements
SC selection and power auto-configuration efficiency depend on these measurements.An inaccurate evaluation of the neighboring cells (macro + other indoor small cells)
characteristics will highly increase
Interferences on the outdoor existing network worst HSxPA performances
Probability of having bad performances on indoor small cell service area
Based on indoor coverage simulations, and field analysis.
With simulation results, an indoor small cell is able to ensure a 10m cell radius with 95%
of area reliability@ -70dBm; with 3dBm pilot EIRP.
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
42/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 42/74
Assumptions
5dB indoor penetration for front window case; 15dB indoor penetration for
indoor penetration including wall
Ec/Io pilot target is -15dB @cell edge when indoor small cell is totally load
with macro RSCP is 3dB higher than indoor small cell.
Indoor small cell pilot EIRP is 3dBm
Indoor small cell can be best server in all indoor when outdoor macro-cell RSCP -60dBm
For a macro-cell -50dBm > outdoor RSCP > -60dBm,
Macro-cell risk to be best server in a part of the indoor area, if such RSCP
level is in front window.
In case of wall penetration indoor small cell, will stay best server
For a macro-cell outdoor RSCP-50dBm,
Macro-cell risk to be best server in indoor area, if such RSCP level is in
front window. Even if wall penetration isolates more indoor small cell from
macro with such outdoor RSCP level macro is best server in major part of
indoor area.
Based on the RSCP distribution, RSCP -50dBm, represents more than 4% of cases, where
indoor small cell risk to be non efficient
Considering macro-cell RSCP estimation, it can be a problem in case of shared carrier
configuration
Indoor small cell placed near a window at firs floor, or ground floor of a building
Indoor small cell receives a good macro-cell RSCP signal
Based on its own model Indoor small cell estimates a very high macro-cell
signal at its cell edge
Indoor small cell increases its power, to have at its cell edge the same signal
than macro-cell
In reality macro-cell outdoor RSCP is quite the same than the one measured
by Indoor small cell. So indoor small cell signal is too high, and can be best
server in the street, which will generate interferences I shared carrierconfiguration
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
43/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 43/74
6.2.1.2 INDOOR SMALL CELL INTERFERS MACRO NETWORK USERS
A UE at macro-cell edge and near indoor small cell edge, will transmit at max power which will
generate high UL interferences for indoor small cell UL performances decrease in indoor small
cell service area
In this configuration the indoor small cells placed in the flat 6 and 8, are best server in their own
indoor area.
The flat7 risk to be highly interfered by indoor small cells, so performances decrease compared to
configuration without indoor small cells
Macro RSCP around -90dBm in flat1 to flat4, due to diffraction on buildings
Flat6 indoor small cell can be best server in flat1 and flat 2 indoor areas:
NOT GOOD!
Flat8 indoor small cell can be best server in flat 3 and flat4 indoor areas.NOT GOOD!
Figure 35: Type of interferences which can occurs with indoor small cell
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
44/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 44/74
There are other cases where indoor small cell have many risk to interfere macro network
users; like:
Positioning indoor small cell near a window; then indoor small cell will extrapolate a
too high Tx power required to fight against macro, and then street macro users will
be interfered.
20mW indoor small cell will not have enough power to fight against macro when air
path loss is lower than 105 dB which represents more than 4% of cases in a real
network, if we consider only street measurements. This % increase considering
higher floor cases, where macro RSCP is higher.
6.2.2 DEDICATED CARRIER
Main problems mentioned previously are resolved.
Very constraining in term of frequency resource
Does an operator is able to provide a carrier which will never be used for outdoor network
in the area where it is deployed in indoor, during all the 3G network life?
Currently ALU is supporting 3 carriers solutions, for macro-cells, so having a dedicated carrier for
indoor seems to be very difficult, except if a new frequency band is free by authorities.
6.2.3 NUMBER OF SCRAMBLING CODE ALLOCATED TO INDOOR SMALL CELLNETWORK
Macro-cell can support 32 SC for neighbors in its list; if 16 SC are reserved for indoor
small cell, 16 SC remain for macro-cells which risk being not enough!!!
For intra-frequency mobility (shared carrier case), only 16 SC for macro-cells neighboring
list is not enough. Seen in the past when only 16 SC can be supported in the neighboring
list
For inter-frequency mobility (dedicated carrier case), if 16 SC are reserved for indoor
small cell, it remains 16 for macro-cells
For mobility in idle mode, 48 neighbors can be supported which summarize intra-freq,
inter-freq, and inter-RAT, reducing the number of this list by 16 for macro neighbors, is too
important!!
-
8/12/2019 UMTS Indoor RF Design Guideline_ External Version-V4.1
45/74
UMTS INDOOR RF DESIGN GUIDELINE
Alcatel-Lucent confidential
UMT/DCL/APP/035536 4.1 / EN Standard 21/JUL/2011 Page 45/74
Worst case study
Assumptions
Two cells cell A and cell B, cell B can re-use cell A scrambling code if:
RSCPcellB RSCPcellA + 10dB everywhere in the cell
100% of flat have a indoor small cell of a same operator
SC can be reused each three floor level
Floor penetration is around 12dB,
Mean Flat dimensions: height:3m; width:5m; length:10m
Wall penetration is 10dB
Window penetration: 2dB
Door penetration: 4dB A indoor small cell is able to cover 90m with a RSCP -78dBm in area with
obstacles and 15dB wall penetration
Indoor small cell are in the centre of each flat
Propagation models