INVITATION FOR QUOTATION
TEQIP-II/2017/RJ1G05/Shopping/242 16-Jan-2017
To,
Sub: Invitation for Quotations for supply of GoodsDear Sir,
1. You are invited to submit your most competitive quotation for the following goods with
item wise detailed specifications given at Annexure I,
Sr. No
Brief Description Quantity Delivery Period(In days)
Place of Delivery Installation Requirement (if any)
1 Digital Electronics & Micro Processor lab Equipment
18 30 M.L.V. TEXTILE & ENGG. COLLEGE, BHILWARA
Yes
2. Government of India has received a credit from the International Development Association
(IDA) towards the cost of the Technical Education Quality Improvement
Programme[TEQIP]-Phase II Project and intends to apply part of the proceeds of this credit
to eligible payments under the contract for which this invitation for quotations is issued.
3. Quotation,
3.1 The contract shall be for the full quantity as described above.
3.2 Corrections, if any, shall be made by crossing out, initialing, dating and re writing.
3.3 All duties and other levies payable by the supplier under the contract shall be included
in the unit price.
3.4 Applicable taxes shall be quoted separately for all items.
3.5 The prices quoted by the bidder shall be fixed for the duration of the contract and
shall not be subject to adjustment on any account.
3.6 The Prices should be quoted in Indian Rupees only.
4. Each bidder shall submit only one quotation.
5. Quotation shall remain valid for a period not less than 55 days after the last date of
quotation submission.
6. Evaluation of Quotations,
The Purchaser will evaluate and compare the quotations determined to be substantially
responsive i.e. which
6.1 are properly signed ; and
6.2 confirm to the terms and conditions, and specifications.
7. The Quotations would be evaluated for all items together.
8. Award of contract:
The Purchaser will award the contract to the bidder whose quotation has been determined
to be substantially responsive and who has offered the lowest evaluated quotation price.
8.1 Notwithstanding the above, the Purchaser reserves the right to accept or reject any
quotations and to cancel the bidding process and reject all quotations at any time
prior to the award of contract.
8.2 The bidder whose bid is accepted will be notified of the award of contract by the
Purchaser prior to expiration of the quotation validity period. The terms of the
accepted offer shall be incorporated in the purchase order.
9. Payment shall be made in Indian Rupees as follows:
Delivery and Installation - 90% of total cost
Satisfactory Acceptance - 10% of total cost
10. All supplied items are under warranty of 24 months from the date of successful acceptance
of items.
11. You are requested to provide your offer latest by 11:00 hours on 30-Jan-2017 .
12. Detailed specifications of the items are at Annexure I.
13. Training Clause (if any) Yes
14. Testing/Installation Clause (if any) Yes
15. Information brochures/ Product catalogue, if any must be accompanied with the quotation
clearly indicating the model quoted for.
16. Sealed quotation to be submitted/ delivered at the address mentioned below,
M L V Govt. Textile & Engineering College, Pur Road, Bhilwara 311001
17. We look forward to receiving your quotation and thank you for your interest in this project.
(Authorized Signatory)
Name & Designation
Digital Electronics & Microprocessor Lab Equipment
S. No.
Package Name Detailed Specification Quantity
1 Advanced Digital WorkStation
It should have following features: Self contained & easy to operate Graphical LCD to show the menu of experiment and
gate level diagram for selected experiments Solder less breadboard On Board DC Power Supply On board Pulse Generator Online Simulation, Teaching & Learning Software on
Digital Electronics Should be housed in compact and light weight
enclosure like laptop Designed on FGPA IC Based Should be able to perform all Digital electronics
experiments on single board Provide all IC and connecting wires.
It should have following Technical Specifications:Size of Breadboard (mm) : 172.5 x 128.5DC Supply : +5 V/1 A +12V/1AClock Frequency : 1 Hz, 100 Hz, 1 KHz, 100 KHzAmplitude : 3.3 V (TTL)Duty cycle : 50 %Graphical LCD : 128 X 64 dotsLED display : 8 Nos. (TTL)Seven Segment Display : 3 Nos.Pulser Switches : 2 Nos.Data switches : 8 Nos. (Toggle switches for both TTL modes)Power Supply : 100V - 240V AC, 50/60Hz Instructions Manual Kits coverIt should have to perform following experiments:
Study of operation of all Logic Gates Half Adder, Full Adder Half subtractor, Full subtractor Binary to Gray Code Conversion Parity checker and Generator Gray Code to Binary Conversion Study of 4 to 2 line Encoder Study of 2 to 4 line Decoder Multiplexer and De-multiplexer Circuits De Morgan's law Study of Flip Flops Asynchronous and Synchronous Binary Up - Down
Counters
1
Study of Johnson Counter Study of Ring Counter Modulo counters Study of Shift Registers
The software should meet following Key Features:The Board should comprise with Online Simulation, Teaching & Learning Software on Digital Electronics. The software should introduce the fundamental concepts of digital systems which should illustrate by various animations and relevant examples for quick understanding of students along with the simplified theory. At the end of each topic relevant quizzes & FAQs should also be given for the students to self estimate their understanding. It should cover following key topics like Digital number system, Boolean Algebra & Logic Circuits, Digital Logic Gates, Simplification of Boolean Functions, Digital Combinational Logic, Combinational Arithmetic Circuits, Sequential Circuits, Digital Logic Families, adder & sub tractor, Multi vibrators, Schmitt trigger, Logic Families, Shift Registers & Counters Semiconductor Memories, Analog to Digital & Digital to Analog converters.
2 Understanding and Experimentation with Digital ICs
Features:Illustration of Combinational and Sequential circuits ZIF Socket provided for easy connectionsCompact sizeSimultaneous use of multiple ICsLearning material CDProvide all IC and connecting wires.Technical SpecificationsMains Supply : 90 V - 250 V, 50 HzFixed DC Power Supply : +12 V, -12 V, +5 V, -5 VFixed TTL Generator : 1 Hz, 10 Hz, 100 Hz, 1 KHz, 10 KHz and 100 KHzPulse Generator : 5 VZIF Socket : 20 Pins (6 Nos.)40 Pins (1 No.)Input Section : 12 toggle switchesOutput Section : 12 LED indicatorDimension (mm) : W 350 x D 280 x H 55Instructions ManualKits coverScope of Learning:Study of Basic GatesStudy of Half Adder using Logic GatesStudy of Full Adder Study of Half & Full Subtractor using Logic GatesStudy of Magnitude Comparator Study of Encoder / Priority Encoder Study of Decoder & Demultiplexers Study of Multiplexers Study of BCD to 7 Segment DisplayStudy of Flip-Flop
1
Study of RegisterStudy of Counter
03. Analog-Digital Circuits Development Platform
Master Unit (A)Size of Breadboard : 172.5 mm x 128.5 mmConnections on Breadboard : 1685DC Power Supply : +5 V; l A, -5 V; 500 mA,+3 V to +15 V; 500 mA(variable)-3 V to -15 V; 500 mA (variable)LED Display : 8 nos (TTL/ CMOS Mode)BCD to Seven Segment Display : 2 nosLogic Probe : Logic level indicator for TTL/ CMOS (7 Segment)Power Supply : 110-220 V ± 10%, 50/60 HzPulser Generator : 1Hz to 1MHz in 6 steps Variable in between stepsAmplitude : 3 V-15 V (CMOS), 5V (TTL) Duty cycle: 50 %, TTL/CMOS outputPulser Switches : 2 nos. (Push to ‘On’)Data Switches : 16 nos (Toggle switches for both TTL & CMOS mode)Weight : 3 Kgs. approximatelyDimensions (mm) : W 326 x H 52 x D 252Learning material : CD (Theory, procedure,reference results, etc).Online (optional)Instructions ManualKits coverProvide all IC and connecting wires.
The software should meet following Key Features:The Board should comprise with Online Simulation, Teaching & Learning Software on Digital Electronics. The software should introduce the fundamental concepts of digital systems which should illustrate by various animations and relevant examples for quick understanding of students along with the simplified theory. At the end of each topic relevant quizzes & FAQs should also be given for the students to self estimate their understanding. It should cover following key topics like Digital number system, Boolean Algebra & Logic Circuits, Digital Logic Gates, Simplification of Boolean Functions, Digital Combinational Logic, Combinational Arithmetic Circuits, Sequential Circuits, Digital Logic Families, adder & sub tractor, Multi vibrators, Schmitt trigger, Logic Families, Shift Registers & Counters Semiconductor Memories, Analog to Digital & Digital to Analog converters.
1
04 Ready to Use Board
Modules Unit (B)A) Logic GatesB) Universal Gate- NAND/NORC) EX-OR Gate ImplementationD) Demorgan's TheoremE) EX-OR Gate Application
Provide one module of each
F) Code Conversion (Binary to Gray & Gray to Binary)G) Code Conversion (BCD to Excess-3 code)H) Binary Adder -SubtractorI) Encoder - DecoderJ) Multiplexer – DemultiplexerK) Flip-Flops (R-S, D, J-K,T)L) Bit Synchronous Binary CounterM) BCD to 7- Segment DecoderN) Digital to Analog Converter (R -2 R ladder)O) Analog to digital converter (Counter Type)P) Monostable MultivibratorsQ) Adder/ Subtractor (4 bit / 8 bit)R) Decoder / DemultiplexerS) Shift register (4 bit SIPO)T) Transfer characteristics (TTL and CMOS Inverters)
5 Logic Gates Trainer
Features:Exclusive and compact designStraight forward representation of all logic gates+5V SMPS Adaptor provided with the trainer for power supplyDesigned by considering all the safety standardsProvided with an extensive manualLow cost trainer including illustration of all logic gatesInstructions ManualKits coverTechnical SpecificationsInput : +5V DCLogic levels : +5V : HIGH ( Logic 1 ) 0V : LOW ( Logic 0 )Scope of LearningStudy of AND gate and to verify its truth tableStudy of OR gate and to verify its truth tableStudy of NOT gate and to verify its truth tableStudy of NAND gate and to verify its truth tableStudy of NOR gate and to verify its truth tableStudy of XOR gate and to verify its truth tableStudy of XNOR gate and to verify its truth table
01
6 Universal Gates Trainer
Features:Exclusive and compact designStraight forward representation of Universal Gates+5V SMPS Adaptor provided with the trainer for power supplyDesigned by considering all the safety standardsProvided with an extensive manualLow cost trainer including illustration of logic gatesdesign using universal gatesInstructions ManualKits coverTechnical SpecificationsInput : +5V DCLogic levels :+5 V : HIGH (Logic 1)
01
0 V : LOW (Logic 0)Dimensions (mm) : D 345 × W 240 × H 110 Weight : 1 Kg.Scope of LearningDesigning of NOT gate using NAND gateDesigning of AND gate using NAND gateDesigning of OR gate using NAND gateDesigning of NOT gate using NOR gateDesigning of AND gate using NOR gateDesigning of OR gate using NOR gat
7 SOP & POS Implementation Trainer
Features:Stand alone system Easy illustration of different types of canonical forms LEDs for visual indication of input and output logic states SPDT switches for input logic selectionInstructions ManualKits coverTechnical SpecificationsDC Power Supply : +5 V DC Logic levels +5 V : High (Logic 1) 0 V : Low (Logic 0)LED Indication : LED will be ON for logic high or '1' state and will be OFF for logic low or '0'stateScope of Learning Study of boolean function in different canonical forms.Study of Quine Mclusky method and realize its NOR-OR implementation.
02
8 Adders and Subtractors Trainer
Features:Exclusive and compact designStraight forward representation of Universal Gates+5V SMPS Adaptor provided with the trainer for power supplyDesigned by considering all the safety standardsProvided with an extensive manualLow cost trainer including illustration of logic gatesdesign using universal gatesInstructions ManualKits coverTechnical SpecificationsInput : +5 V DCLogic levels :+5 V : HIGH(Logic 1)0 V : LOW (Logic 0)Dimensions : W 240 × D 345 × H 110Weight : 1Kg.Scope of LearningStudy of Binary Half AdderStudy of Binary Full Adder using two Half AddersStudy of Binary Half Subtractor
01
9 Parallel Adder and Subtractor Trainer
Features4-bit/8-bit Binary Addition & SubtractionEasy switching between addition and subtraction modes
01
LEDs for visual indication of input-output & carry out logicsInstructions ManualKits coverTechnical SpecificationsDC Power Supply : +5 V DCLogic levels+5 V : High (logic 1) 0 V : Low (logic 0)LED indication : LED will be ON for logic high or '1' state and willbe OFF for Logic low or '0' stateScope of Learning To study 4-bit binary addition and subtraction operation To study 8-bit binary addition and subtraction operation
10 Multiplexer and Demultiplexer
Features:+5V SMPS Adaptor provided with the trainer for power supplyEasy illustration of Multiplexer and DemultiplexerLEDs for visual indication of inputs and outputs statusSPDT switches for logic selectionGood quality, reliable sockets are provided at appropriate places on board for connectionsStrongly supported by systematic operating instructionsA low cost training systemInstructions ManualKits coverTechnical Specifications:Input : +5V DC Logic levels+5V : HIGH (Logic 1)0V : LOW (Logic 0)Dimensions (mm) : 240 W × 345 D ×110 HWeight : 1Kg. (approx.)LED Indication : LED will ON (glow) for 1 state and will be OFF for 0 state.
Scope of Learning:Study and verification of the Truth Table of 4-to-1 Line MultiplexerStudy and verification of the Truth Table of 1-to-4 Line DeMultiplexer
01
11 Flip-Flop Trainer Features:Exclusive and compact designAdaptable illustration of Flip-Flops+5V SMPS Adaptor provided with the trainer for power supplyDesigned, considering all the safety standardsProvided with an extensive manualA low cost training systemInstructions ManualKits coverTechnical Specifications:
01
Input : +5V DCLogic levels +5V : HIGH(Logic 1)0V : LOW (Logic 0)Dimensions (mm) : W 240 x D 345 x H 110Weight : 1kg (approximate)Scope of Learning with clock and without clock:-Study of S-R Flip-Flop and to verify its Transition tableStudy of J-K Flip-Flop and to verify its Transition tableStudy of D Flip-Flop and to verify its Transition tableStudy of T Flip-Flop and to verify its Transition table
12 Counters Trainer Features:Stand Alone systemEasy illustration of different types of countersLEDs for visual indication of input andoutput logic statesSPDT switches for input logic selectionInstructions ManualKits coverTechnical Specifications: DC Power Supply : +5 V DCLogic levels+5 V : High (Logic 1)0 V : Low (Logic 0)LED Indication : LED will be ON for logic high or'1' state and will be OFF for logic low or '0' stateScope of Learning:Study of 4-bit synchronous binary up CounterStudy of 4-bit asynchronous binary up/down CounterVerification of operation of IC 74LS190 as a modulo-N programmable Counter
01
13 Shift Registers Trainer
Features:Stand alone systemEasy illustration of all types of 3-bit and 4-bit shift registersLEDs for visual indication of input and output logic statesSPDT switches for easy input logic selectionInstructions ManualKits coverTechnical Specifications:DC Power Supply : +5VLogic levels+5 V High (Logic 1)0 V Low (Logic 0)LED Indication LED will be ON for logic high or '1' state and will be OFF for logic low or '0' stateScope of LearningStudy of 3-bit and 4-bit serial in serial out shift registerStudy of 3-bit and 4-bit serial in parallel out shift registerStudy of 3-bit and 4-bit parallel in serial out shift registerStudy of 3-bit and 4-bit parallel in parallel out shift register
01
14 Understanding Microprocessor 8085
Diagrammatic representation of full system Powerful monitor program Battery backup for RAM Three channel Timer/counter using 8253 48 I/O lines using 8255 On board EPROM programmer for 27 series On board 8 channel 8 bit ADC On board 8 bit 2 Channel DAC Facility of downloading and uploading the files
from PC through PC Software PC Software with features like sending commands
to Microprocessor Trainer Kit, user can change the RAM Data & change the location of RAM Data
Two command mode interface ASCII Keyboard Serial Mode + 12V, + 5V – 500mA SMPS Based Power supply
on board All Address and Control lines are available on 50
pin Connector Online Simulation, Teaching & Learning Software
on Microprocessor Should be housed in compact and light weight
enclosure like laptop Instructions Manual Kits cover
The Trainer should have following Technical Specifications: Operating Frequency : 6.144 MHz
ROM : 8 K
RAM : 8 K
Input : ASCII Keyboard
Display : 20 X 2 LCD
Mains supply (SMPS) : 90 - 230 V AC,50 Hz
The Trainer should comprises with following application modules:
Digital Input Output Seven Segment Display Stepper Motor Controller DC Motor Controller Traffic Light Controller Temperature Measurement Relay & OPTO Coupler Elevator Simulator Thumb Wheel Switch
02
Experiments to be Performed :-1.Arranging a set of data in Ascending order.2 Arranging a set of data in Descending order.3 Finding out number of Positive, Negative and Zeros from a Data Set.4 Searching the Existence of a certain data in a given data.5 BCD to Binary conversion.6 Binary to BCD conversion7 Design a Up/Down Counter8 Multiply Two 8 Bit Numbers using Successive Addition and Shifting method.9 Find Factorial of a number.10 Solve the given Algebraic Equation11 Generate a Software Delay.12.Division of 8 bit Unsigned Numbers.
Modules Should have following features & Technical Specifications
Should compatible with 8085 Microprocessor Trainer Learning Material with theory, procedure, results,
programs etc. Interface : 26 Pin FRC Operating Voltage : +5V,+/- 12V
The online learning, teaching & simulation software should have following Key Features:
It should provide basic information about 8085 microprocessor and peripherals. It should provide with basic concept for a full understanding of microprocessor and its peripherals in a manner that is clearer, interesting, and easier to understand through innovative graphical user interface which is easy to learn and extremely efficient to use. The software should developed as a self-study package with easy-to-navigate interface, explaining difficult electronics concepts by analogies, flash animations and examples and cover topics like architecture of a 8-bit, Microprocessor, assembly Language Programming, Special Purpose Programmable Peripheral Devices and Their Interfacing Topics with Programmable Interval Timer (8253/8254), Programmable Interrupt Controller (8259), Keyboard/Display Controller (8279), Programmable Communication Interface (8251), DMA Controller (8237/8257), Microprocessor Applications.
15 Interfacing Module for Microprocessor
a) 8253 Programmable Internal Timerb) 8155 Programmable I/O & Timerc) 8255 Prog. Peripheral interfaced) 8251 Prog.commutation interfacee) 8X8 LED Matrix Displayf) Seven Segment Display
Provide one module of each
g) 16X2 LCD Displayh) Stepper Motor Controlleri) 8 Channel 8 Bit ADCj) 2 Channel 8 Bit DACk) Traffic Light Controllerl) Temperature Measurement
Note - Instructions Manual Kits cover Should be provide.
Experiments to be covered.Generate a square wave and rectangular wave of given frequency at the Output pin of 8255 chip.A program to display real time clock. Assume a periodic signal is interrupting RST 7.5 signal after every 0.5 seconds,
16
8085 Microprocessor
FeaturesDiagrammatic representation of full systemTwo modes of command HEX key pad mode Serial mode Facility of downloading and uploading the files from PC Powerful monitor program All Address and Data lines are provided on 50 pin connector Battery Backup for RAMThree channel Timer/Counter using 8253 24 I/O lines provided through 8255 22 I/O lines provided through 8155 Instructions Manual Kits covered
Technical SpecificationsOperating Frequency : 6.144MHzRAM : 8KROM : 8KInput : 7 x 4 HEX keypadDisplay : Seven segmentMains supply : 90 - 230V AC, 50HzFuse : 500mA
The online learning, teaching & simulation software should have following Key Features:
It should provide basic information about 8085 microprocessor and peripherals. It should provide with basic concept for a full understanding of microprocessor and its peripherals in a manner that is clearer, interesting, and easier to understand through innovative graphical user interface which is easy to learn and extremely efficient to use. The software should developed as a self-study package with easy-to-navigate interface, explaining difficult electronics concepts by analogies, flash animations and examples and cover topics like architecture of a 8-bit,
05
Microprocessor, assembly Language Programming, Special Purpose Programmable Peripheral Devices and Their Interfacing Topics with Programmable Interval Timer (8253/8254), Programmable Interrupt Controller (8259), Keyboard/Display Controller (8279), Programmable Communication Interface (8251), DMA Controller (8237/8257), Microprocessor Applications.
17 Advanced Analog Circuits Development Platform & Analog Electronics teaching software
Features:Self Contained and Easy to OperateFunctional Blocks indicated on board mimicOn board DC and AC Power SupplyOn board Function GeneratorOn board Continuity TesterOn board Toggle Switches and PotentiometersSolder less BreadboardOn Board Voltage/ Current/Frequency MeasurementPC InterfaceProvide all Ics to perform experiments listed below –each 5 nos.Instructions Manual Kits cover
Technical Specifications:DC Power Supplies : + 5V, 1 A (Fixed)+ 12V, 500 mA (Fixed)-12V, 500 mA (Fixed)+ 12V, 500 mA (Variable)-12V, 500 mA (Variable)AC Supply : 9V-0V-9V, 500mABreadboard : Breadboard for making various circuits and testing them.External components/IC can be fitted conveniently.Function generator : Operating modes Sine, Square and Triangular.Frequency range 1 Hz to 100 KHz.Volt/Current/Frequency : Voltage Range +12V to -12VMeasurement Current Range 0 to 500mAFrequency Range DC to 100KHz (All with respect to Ground)PC Interface : Acquisition from two Analog input channels (Max. input 1 Volt)Continuity Tester : For testing the continuity.Provided with Beeper Sound.Power Supply : 110-220 V ±10%, 50/60Hz.Weight : 3.5 Kg approximatelyIncluded Accessories :Bread Board : 2 nos.Connecting Wire : 50 nos.2mm to 1mm Patch cord : 10 nos.2mm to 2mm Patch cord 16” : 10 nos.Mains Cord : 1 no.Simulation software Advanced Analog electronics: 1 no.Electronics Software CDLearning Material (CD) : 1 no.Interface Cable (microphone pin) : 1 no.
03
Software : 1 no.
Analog Electronics(Simulation software)Though we are leaving in digital world, Analog Electronics is a vital part of electronics engineering; for understanding advance technologies in electronics, the student have to have the knowledge of basic principles of Electronics. And for this we came with very good software “Simulation software Analog Electronics”, which comprises of simulations, animations, along with mandatory theory to understand fundamental concepts of Analog Electronics.FeaturesBasic Electrical ConceptsBasic CircuitsFundamentals of Resistor/Capacitor/Inductor TransformersSemiconductors & DiodesTransistor & basic transistor circuitsOperational Amplifiers (Op-Amps): Characteristics & SpecificationsPractical Op-Amp circuitsPower Supplies & Rectifiers
Experiments to be covered1.Op-Amp characteristics and get data for input bias current measure the output-offset voltage and reduce it to zero and calculate slew rate.2 Op-Amp in inverting and non-inverting modes.3 Op-Amp as scalar, summer and voltage follower.4 Op-Amp as differentiator and integrator.5 Design LPF and HPF using Op-Amp 7416 Design Band Pass and Band reject Active filters using Op-Amp 741.7 Design Oscillators using Op-Amp (i) RC phase shift (ii) Hartley (iii) Colpitts8 Design (i) Astable (ii) Monostable multivibrators using IC-555 timer9 Design Triangular & square wave generator using 555 timer.10 Design Amplifier (for given gain) using Bipolar Junction Transistor.
18 Operational Amplifier Lab
Mains power supply :90 - 270V ±10%, 50Hz (SMPS)Function GeneratorSine Wave Frequency :1KHz to 100KHz Frequency Control :100KV, 10 turn PotentiometerAmplitude :0V to 5VppAmplitude Control :100KV, Single turn PotentiometerTriangular WaveFrequency :1KHz to 100KHz Frequency Control :100KV, 10 turn PotentiometerAmplitude :0V to 5VppAmplitude Control :100KV, Single turn PotentiometerSquare Wave Frequency : 1KHz to 100KHz
07
Frequency Control :100KV, 10 turn PotentiometerAmplitude :5Vpp, fixedFixed DC power supply :+12V, Regulated-12V, Regulated+5V, Regulated-5V, RegulatedVariable DC power supply :+1.5V to +10V Regulated using LM317:-1.5V to -10V Regulated using : LM337Bread BoardDimension(mm) :175 x 61 x 10Distribution strips :2Distribution holes :200Terminal holes :640Op-amp :IC uA741 (2 Nos.) :All pins terminated on 2 mmBanana SocketsConnecting Wire : 50 nos.Supply Voltage :±22V max.Differential Input Voltage :±30V max.Input Voltage :±15V max.Slew Rate :0.5 V/µs (VCC = ±15V)Provide all Ics to perform experiments listed below –each 5 nos. Diode 1N 4007 :2 nos.Capacitor Bank : each 5 nos. Electrolyte Cap. 1mf/63V Disc cap. 1nf/63VDisc cap. 10nf/63VDisc cap. 100nf/63VResistor Bank : SMD Resistance 1KV1% 1/4W (5 Nos.)SMD Resistance 10KV1% 1/4W (5 Nos.)SMD Resistance 100KV1% 1/4W (5 Nos.)Variable Resistance bank1KVSingle turn Potentiometer (2 Nos.)10KVSingle turn Potentiometer (2 Nos.)100KVSingle turn Potentiometer (2 Nos.)1MVSingle turn Potentiometer (2 Nos.)Fuse : 500mA, slow blowDimensions (mm) : W 350 x D 280 x H 55
Analog Electronics(Simulation software)Though we are leaving in digital world, Analog Electronics is a vital part of electronics engineering; for understanding advance technologies in electronics, the student have to have the knowledge of basic principles of Electronics. And for this we came with very good software “Simulation software Analog Electronics”, which comprises of simulations, animations, along with mandatory theory to understand fundamental concepts of Analog Electronics.FeaturesBasic Electrical ConceptsBasic CircuitsFundamentals of Resistor/Capacitor/Inductor TransformersSemiconductors & DiodesTransistor & basic transistor circuits
Operational Amplifiers (Op Amps): Characteristics & SpecificationsPractical Op Amp circuitsPower Supplies & RectifiersInstructions Manual Kits cover
Experiments to be covered1.Op-Amp characteristics and get data for input bias current measure the output-offset voltage and reduce it to zero and calculate slew rate.2 Op-Amp in inverting and non-inverting modes.3 Op-Amp as scalar, summer and voltage follower.4 Op-Amp as differentiator and integrator.5 Design LPF and HPF using Op-Amp 7416 Design Band Pass and Band reject Active filters using Op-Amp 741.7 Design Oscillators using Op-Amp (i) RC phase shift (ii) Hartley (iii) Colpitts8 Design (i) Astable (ii) Monostable multivibrators using IC-555 timer9 Design Triangular & square wave generator using 555 timer.10 Design Amplifier (for given gain) using Bipolar Junction Transistor.
FORMAT FOR QUOTATION SUBMISSION
(In letterhead of the supplier with seal)
Date: _______________
To:
____________________________
____________________________
Sl.
No.
Description of
goods (with full
Specifications)
Qty. Unit Quoted Unit rate in Rs.
(Including Ex Factory price, excise duty, packing and
forwarding, transportation, insurance, other local
costs incidental to delivery and warranty/ guaranty
commitments)
Total Price
(A)
Sales tax and other
taxes payable
In
%
In figures
(B)
Total Cost
Gross Total Cost (A+B): Rs. ________________
We agree to supply the above goods in accordance with the technical specifications for a total contract price of Rs. ———————— (Amount in figures) (Rupees ————————amount in words) within the period specified in the Invitation for Quotations.
We confirm that the normal commercial warranty/ guarantee of ——————— months shall apply to the offered items and we also confirm to agree with terms and conditions as mentioned in the Invitation Letter.
We hereby certify that we have taken steps to ensure that no person acting for us or on our behalf will engage in bribery.
Signature of SupplierName: __________________Address: __________________Contact No: ______________