Download - WCDMA RBS Commissioning
WCDMA RBS Commissioning
Table of Contents
Connect to RBS Using Laptop......................................................................................................2Format C2 and D drives and enter IP address in the RBS...........................................................4Set RBS Password.......................................................................................................................7Perform Initial Software Load.......................................................................................................9Upgrade System Software..........................................................................................................11Cabinet and Equipment Configuration........................................................................................17OAM Access Configuration Script..............................................................................................22Site Equipment Configuration Script...........................................................................................30Site Complete Configuration Scripts...........................................................................................37Create Site Complete Configuration Version (CV).....................................................................40
1 of 42
Connect to RBS Using Laptop
Connect to RBS
Use the following steps to connect your laptop to the RBS.
Step Action1 Connect the Laptop to the RBS using the RS-232 port and LAN cable.2 Launch HyperTerm and connect to RBS.3 Enter ifconfig to display the RBS IP information.
4 Record the RBS IP address and Subnet Mask.5 Open the TCP/IP properties for the laptop LAN port and:
Set the IP address to 1 higher than the RBS address. Set the subnet mask to the subnet mask in the RBS. Set the default gateway to the RBS IP address value
2 of 42
Copy Operational RBS Image to Laptop
Copy RBS Image to Laptop
Step Action1 Use WS_FTP Pro to copy the image from the RBS to a new
directory on the laptop.
Step Action1 Create a new folder under the root directory of the
laptop.2 Stop Symantec if it is loaded and running on the laptop.3 Launch WS_FTP Pro.4 Set the left window (local) to the newly created directory
on the laptop.5 Enter the node ip address in the IP address field.6 Enter the UserID and Password in their respective fields
and click Go.7 Set the right window (remote) to show the C and D
drives in the window.8 Copy the C and D drives from the node to the laptop
(right to left—Download arrow).9 Rename the C drive to C2.
3 of 42
Format C2 and D drives and enter IP address in the RBS
Format C and D Drives
Use the following steps to format the C and D drives and enter the IP address in the RBS.
Step Action1 Shut off the fan circuit breakers (CB1 and CB2).2 In the HyperTerm window, type reload -- to put the RBS into the
Backup mode.
3 Type formathd /d to format the D drive.
Danger: Do not type format or the CBU card will be toast and must be sent to Ericsson for repair.
Continued on next page
4 of 42
Format C2 and D drives and enter IP address in the RBS, Continued
Format C and D Drives, continued
4 Type formathd /c2 to format the C drive.
Danger: Do not type format or the CBU card will be toast and must be sent to Ericsson for repair.
5 Type reload -- to put the RBS into the Backup mode again.
Continued on next page
5 of 42
Format C2 and D drives and enter IP address in the RBS, Continued
Format C and D Drives, continued
Step Action6 Type ifconfig le0 <rbs ip addr> netmask <rbs subnet mask>.
7 Type ifconfig to verify the RBS IP configuration.
6 of 42
Set RBS Password
Set Password Use the following steps to set the RBS password.
Step Action1 Type passwd2 Type rbs (won’t show on screen).3 Type rbs (won’t show on screen).
4 Type reload to activate the RBS password and IP configuration.
Continued on next page
7 of 42
Set RBS Password, Continued
Set Password, continued
Step Action5 Type reload -- to put the RBS into the Backup mode.
8 of 42
Perform Initial Software Load
Initial Software Load
Use the following steps to perform the initial software load.
Step Action1 Stop Symantec if it is loaded and running on the laptop.2 Launch WS_FTP Pro.3 If needed, enter the RBS IP address, ID, and password. Click Go4 Set the left window (local) to the basic package being loaded so
the C2 and D drives are visible.(class cd\!asp_scripts_packages\basic\CXP901250%1_R1C\hard disk)
5 Set the right (remote) window to the root of the RBS6 Select the C2 and D drives in the left (local) window7 Copy the C2 and D drives from the laptop to the RBS.
(left to right—Upload arrow)
Wait for the upload to complete successfully
Continued on next page
9 of 42
Perform Initial Software Load, Continued
Initial Software Load, continued
Step Action8 Type reload and wait for it to complete (up to 4 minutes). When
completed, the CBU LED will be steady green and the system will display “security properties not found – using defaults” in the HyperTerm window.
10 of 42
Upgrade System Software
Upgrade System Software
Use the following steps to upgrade the system software.
Step Action1 Launch the Cesar FTP server.2 Click the “Little man” icon on the toolbar.
3 Click the appropriate entry in the users & groups list. Create a new entry if needed.
4 Enter anonymous in the login field.5 Click the Anonymous Access button.6 Click the File Access Rights button.
Continued on next page
11 of 42
Upgrade System Software, Continued
Upgrade System Software, continued
Step Action7 In the Cesar FTP browser window (upper left) navigate to the
directory containing the upgrade software and drag the directory to the lower window and click OK on user group window.
8 Launch the Firefox browser and enter the Element Manager address in the address bar (http://<node ip addr>/em/index.html).
Continued on next page
12 of 42
Upgrade System Software, Continued
Upgrade System Software, continued
Step Action9 After Element Manager launches, use the drop-down list to go to
the Software view.
10 Click + (the plus sign) to expand SWManagement.11 Right click Upgrade Packages.12 Click Create.13 Fill in the name of the upgrade package using the folder with the
aue, java, and xml files (use the complete path on the laptop). Precede to the path with ./ and copy the path and file name from the laptop and paste it in the field.
14 Enter the laptop IP address in the FTP Server Address field and the upgrade package name in the user label field (ex. UP_CXP9012073).
15 Click Create Package and wait for the transfer to complete successfully.
Continued on next page
13 of 42
Upgrade System Software, Continued
Upgrade System Software, continued
Step Action16 Click Install Package.
17 Click Full Install and wait for the installation to complete successfully (at this point you’re done with Cesar).
Continued on next page
14 of 42
Upgrade System Software, Continued
Upgrade System Software, continued
Step Action18 After the installation completes successfully click Upgrade Node.
19 Click Hard Upgrade.
Continued on next page
15 of 42
Upgrade System Software, Continued
Upgrade System Software, continued (continued)
Step Action20 Monitor the upgrade progress with the window maximized and wait
for successful completion.
Step Action1 The system will reset twice. You may see an error
message warning of a different version of Element Manager if you are upgrading from P5 to P6.
If this happens, close EM and Firefox and launch the newer Element Manager from your desktop.
2 Reconnect to the RBS with Element Manager.3 Open Software view.4 Expand SWManagement.5 Select Upgrade Packages.6 Right-click the update package and select Confirm
Upgrade. Click Yes to confirm the confirmation.
7 You may have to change views and go back to confirm the upgrade.
16 of 42
Cabinet and Equipment Configuration
Equipment Configuration
Use the following steps to configure the cabinet and equipment.
Step Action1 In Element Manager click Configuration and select Cabinet
Equipment.
2 Click Next.
Continued on next page
17 of 42
Cabinet and Equipment Configuration, Continued
Equipment Configuration, continued
Step Action3 Click Next. The system will auto-detect the cabinet equipment.
4 Click Next.
Continued on next page
18 of 42
Cabinet and Equipment Configuration, Continued
Equipment Configuration, continued
Step Action5 For each sector to be activated, select the appropriate building
block code from the drop-down list. Use RB1 in the lab system and then click Next when all of the required fields are populated.
6 Click Next.
Continued on next page
19 of 42
Cabinet and Equipment Configuration, Continued
Equipment Configuration, continued
Step Action7 Click Next.
8 Enter the node IP address and Subnet mask and then click Next.
Continued on next page
20 of 42
Cabinet and Equipment Configuration, Continued
Equipment Configuration, continued
Step Action9 Click Finish and click Yes to confirm. Verify successful
completion.
21 of 42
OAM Access Configuration Script
OAM configuration
Use the following steps to run the O&M Access script.
Step Action1 Restart Element Manager.2 Click Configuration and select OAM Access.
3 Click Next.
Continued on next page
22 of 42
OAM Access Configuration Script, Continued
Step Action
4 Click to check Use Configuration File.
5 Click the Browse button.6 Navigate to class cd\!asp_scripts_packages and select the
xxxx_OAM_Access.xml file and click Open.
OAM Access Configuration Script, Continued
23 of 42
OAM configuration, continued
Step Action7 Verify that the Wizard button is selected and click Next.
8 Click Next.
Continued on next page
24 of 42
OAM Access Configuration Script, Continued
OAM configuration, continued
Step Action9 Click Next.
10 Click Next.
Continued on next page
25 of 42
OAM Access Configuration Script, Continued
OAM configuration, continued
Step Action11 Click Next.
12 Click Next.
Continued on next page
26 of 42
OAM Access Configuration Script, Continued
OAM configuration, continued
Step Action13 Click Next.
14 Click Next.
Continued on next page
27 of 42
OAM Access Configuration Script, Continued
OAM configuration, continued
Step Action15 Click Next.
16 Click Next.
Continued on next page
28 of 42
OAM Access Configuration Script, Continued
OAM configuration, continued
Step Action17 Click Finish and verify the successful completion.
18 Click OK.
29 of 42
Site Equipment Configuration Script
Site equipment configuration
Use the following steps to run the site equipment configuration script.
Step Action1 Click Configuration and select Site Equipment.
2 Click Next.
Continued on next page
30 of 42
Site Equipment Configuration Script, Continued
Site equipment configuration, continued
Step Action3 Click to check Use Configuration File.
4 Click the Browse button.5 Navigate to class cd\!asp_scripts_packages and select the
xxxx_external_HW.xml file.6 Click Open and verify that the Wizard button is selected and click
Next.7 Click Next.
Continued on next page
31 of 42
Site Equipment Configuration Script, Continued
Site equipment configuration, continued
Step Action8 Click Next.
9 Click Next.
Continued on next page
32 of 42
Site Equipment Configuration Script, Continued
Site equipment configuration, continued
Step Action10 Click Next.
11 Click Next.
Continued on next page
33 of 42
Site Equipment Configuration Script, Continued
Site equipment configuration, continued
Step Action12 Click Next.
13 Click Next.
Continued on next page
34 of 42
Site Equipment Configuration Script, Continued
Site equipment configuration, continued
Step Action14 Click Next.
15 Click Next.
Continued on next page
35 of 42
Site Equipment Configuration Script, Continued
Site equipment configuration, continued
Step Action16 Click Finish and verify the successful completion.
17 Click OK.
36 of 42
Site Complete Configuration Scripts
Site Complete Configuration
Use the following steps to run the site complete configuration script.
Step Action1 Click Configuration and select Run Command File.
2 Click the Browse button.
Continued on next page
37 of 42
Site Complete Configuration Scripts, Continued
Site Complete Configuration, continued
Step Action3 Navigate to class cd\!asp_scripts_packages and click the
xxxx_RBS_Site Complete_2T_P6.mo file. 4 Click Open.5 Click to check Halt on Errors and Verbose Logging.
6 Verify that Client is selected.7 Click Start.
Continued on next page
38 of 42
Site Complete Configuration Scripts, Continued
Site Complete Configuration, continued
Step Action8 Wait for Configuration succeeded or a fault message.
9 Click Close.
39 of 42
Create Site Complete Configuration Version (CV)
Create Site Complete CV
Use the following steps to create the site complete configuration version (CV).
Step Action1 In Element Manager select the Software view. 2 Expand SWManagement.
3 Right click Configuration Version and select Create.4 In the Name field enter SC_CXP9012073_1_R6A_2 (Use a name
that matches your software version if different from the example in this step).
5 Click Create.
Continued on next page
40 of 42
Create Site Complete Configuration Version (CV), Continued
Create Site Complete CV, continued
Step Action6 Right-click the CV that was just created and select Set Startable.
7 Right-click the same CV and select Reload with this CV.
Continued on next page
41 of 42
Create Site Complete Configuration Version (CV), Continued
Create Site Complete CV, continued
Step Action8 Select Restart Warm and then click the Restart button. Wait for
the restart to complete and Element Manager to reload.
9 Verify that the CV is Startable and running (purple icon displays).
42 of 42