PART A
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
CIVIL WORKS
1.0 Earth Works 323,788
2.0 Concrete Works 719,899
3.0 RCC Works 6,999,127
4.0 Brick Wok 1,023,313
5.0 Marble/Granite Works 21,021
6.0 Wood & PVC Works 2,261,173
7.0 Flooring Works 3,283,681
8.0 Finishing Works 381,116
9.0 Aluminium Works 128,669
10.0 Water Proofing Works 181,293
11.0 R/F Steel 5,060,800
TOTAL CIVIL WORKS 20,383,881
ELECTRICAL WORKS
12.0 LIGHT FIXTURES 155,870
13.0 INTERNAL WIRING 500,460
14.0 COMPUTER WIRING 54,720
15.0 DB's/FLOOR PANEL 326,000
16.0 LT CABLES AND TERMINATIONS 85,060
17.0 DATA CABLE 98,400
18.0 EARTHING 37,950
TOTAL ELECTRICAL WORK 1,258,460
19.0 PLUMBING & SANITARY 569,218
TOTAL CIVIL, ELECTRICAL, PLUMBING 22,211,559
SUMMARY PART - I BOQ for CIVIL WORKS, ELECTRICAL WORKS and PLUMBING
WORKS based on DSR -2014
Signature of EPIL Page - 2 Signature of Bidder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
New Girls Hostel building, Ahmedabad
RCC Framed Structure, G+4
1075 sq.mts.
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
1.0 2.000 EARTH WORK
1.0
2.600
Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means over areas
(exceeding 30 cm in depth 1.5 m in width as well as 10
sqm on plan) including disposal of excavated earth, lead
up to 50m and lift up to 1.5 m disposed earth to be
leveled and neatly dressed.
1.1 2.6.1 All kinds of soil cum 467 155.60 72,594
1.22.260
Extra for every additional lift of 1.5 m or part thereof in
1.3 2.26.1 All kinds of soil (1.5 mt to 3.0 mt) cum 392 46.25 18,139
1.4
2.250
Filling available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc.in layers not
exceeding 20 cm in depth, consolidating each deposited
layer by ramming and watering, lead up to 50 m and lift
up to 1.5 m.
cum 487 112.40 54,730
1.52.340
Supplying chemical emulsion in sealed containers
including delivery as specified.
2.34.1Chlorpyriphos/ Lindane emulsifiable concentrate of
20%
Litre 693 185.95 128,863
1.6
2.35.3
Treatment of soil under existing floors using chemical
emulsion @ one litre per hole, 300 mm apart including
drilling 12 mm diameter holes and plugging with
cement mortar 1 :2 (1 cement : 2 Coarse sand) to match
the existing floor :
2.35.3.1With Chlorpyriphos/Lindane E.C. 20% with 1%
concentration
Sqm 416 118.90 49,462
SUB TOTAL 323,788
2.0 4.000 CONCRETE WORK
Providing and Laying in position cement concrete of
specified grade excluding the cost of centring and
shuttering – All work upto plinth level.
2.14.1.3
1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
cum 52 5466.30 284,248
2.2 4.1.8
1:4:8 (1 cement : 4 coarse sand : 8 graded stone
aggregate 40 mm nominal size)
cum 98 4301.15 422,255
0
2.3
4.170
Making plinth protection 50 mm thick of cement
concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone
aggregate 20 mm nominal size) over 75mm thick bed of
dry brick ballast 40 mm nominal size, well rammed and
consolidated and grouted with fine sand, including
finishing the top smooth.
Sqm 32 419.30 13,397
Client : NATIONAL INSTITUTE OF DESIGN
Architect: R T & ASSOCIATES PVT LTD.
PART - I BOQ for CIVIL WORKS, ELECTRICAL WORKS and PLUMBING WORKS based on DSR -2014
Executing Agency: Engineering Projects India Ltd. (EPIL)
Project Name:
Type of Structure:
Total Built-up Area:
Signature of EPIL 3 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
SUB TOTAL 719,899
3.0 5.000REINFORCED CEMENT CONCRETE WORK
3.15.9
Centring and shuttering including strutting, propping
etc. and removal of form for:
3.1.15.9.1
Foundations, footings, bases of column etc. for mass
concrete.
Sqm 600 196.45 117,870.00
3.2
5.370
Providing and laying in position ready mixed M-25
grade concrete for reinforced cement concrete work,
using cement content as per approved design mix,
manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads,
having continuous agitated mixer, manufactured as per
mix design of specified grade for reinforced cement
concrete work, including pumping of R.M.C. from
transit mixer to site of laying , excluding the cost of
centering, shuttering finishing and reinforcement,
including cost of admixtures in recommended
proportions as per IS : 9103 to accelerate/ retard setting
of concrete, improve workability without impairing
strength and durability as per direction of the Engineer -
in - charge.
(Note :- Cement content considered in this item is @
330 kg/cum. Excess/less cement used as per design mix
is payable/recoverable separately).
3.2.1 5.37.1 All Works up to Plinth Level cum 274 6644.60 1,818,215
3.2.2 5.37.2 All Works above Plinth Level upto Floor V Level cum 688 7363.00 5,063,042
SUB TOTAL 6,999,127
4.0 6.000 BRICK WORK
4.0
6.400
Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level in
all shapes and sizes in :
4.1 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 180 5426.15 976,707
4.2
6.130
Half brick masonry with common burnt clay F.P.S.
(non modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level.
4.3 6.13.2 Cement Mortar 1:4 (1 cement : 4 coarse sand) sqm 70 665.80 46,606
SUB TOTAL 1,023,313
Signature of EPIL 4 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
5.0 8.000 MARBLE GRANITE WORKS
8.200
Providing and fixing 18 mm thick gang saw cut, mirror
polished, premoulded and prepolished, machine cut for
kitchen platforms, vanity counters, window sills , facias
and similar locations of required size, approved shade,
colour and texture laid over 20 mm thick base cement
mortar 1:4 (1 cement : 4 coarse sand), joints treated
with white cement, mixed with matching pigment,
epoxy touch ups, including rubbing, curing, moulding
and polishing to edges to give high gloss finish etc.
complete at all levels.
8.2.2 Granite of any colour and shade
8.2.2 Granite of any colour and shade
5.1 8.2.2.2 Area of slab over 0.50 sqm sqm 4 3907.40 15,630
8.300
Providing edge moulding to 18mm thick marble stone
counters,Vanities etc. Inbcluding machine polishing to
edge to give high gloss finish etc. complete as per
design approved by Engineer-in-Charge
5.2 8.3.2 Granite work metre 15 230.55 3,458
5.3
8.500
Extra for providing opening of required size & shape
for wash basins/kitchen sink in kitchen platform, vanity
counters and similar location in marble/stone work
including necessary holes for pillar taps etc .including
rubbing and polishing of cut edges etc. complete.
each 5 386.60 1,933
SUB TOTAL 21,021
6.0 9.000 WOOD AND PVC WORK
Room Doors
9.200
Providing and fixing ISI marked flush door shutters
conforming to IS : 2202 (Part I) decorative type, core of
block board construction with frame of 1st class hard
wood and well matched teak 3 ply veneering with
vertical grains or cross bands and face veneers on both
faces of shutters.
6.19.20.1
35 mm thick including ISI marked Stainless Steel butt
hinges with necessary screws.
sqm 75 2606.45 195,484
6.2
9.240
Extra for providing vision panel not exceeding 0.1 sqm
in all type of flush doors (cost of glass excluded)
(overall area of door shutter to be measured):
9.24.1 Rectangular or square sqm 15 139.40 2,091
6.3
9.530
Providing 40x5 mm flat iron hold fast 40 cm long
including fixing to frame with 10 mm diameter bolts,
nuts and wooden plugs and embeddings in cement
concrete block 30x10x15cm 1:3:6 mix (1cement : 3
coarse sand : 6 graded stone aggregate 20mm nominal
size)
each 111 117.35 13,026
Signature of EPIL 5 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
6.4
9.970
Providing and fixing aluminium tower bolts, ISI
marked, anodised (anodic coating not less than grade 10
as per IS:1868), transparent or dyed to required colour
or shade, with nuts and screws etc. complete
9.97.2 250x10 mm each 37 95.25 3,524
6.5
9.101
Providing and fixing aluminium hanging type floor
door stopper (anodic coating not less than grade 10 as
per IS:1868), transparent or dyed to required colour or
shade, with nuts and screws etc. complete
each 37 37.50 1,388
9.101.1 Single rubber stopper
6.6
9.840
Providing and fixing aluminium extruded section body
tubular type universal hydraulic door closer (having
brand logo with ISI, IS : 3564, embossed on the body,
door weight upto 36 kg to 80 kg and door width from
701 mm to 1000 mm), with double speed adjustment
with necessary accessories and screws etc. complete.
each 5 1043.60 5,218
6.7
9.96
Providing and fixing aluminium sliding door bolts ISI
marked anodised anodic coating not less than grade AC
10 as per IS:1868) transparent or dyed to required
colour or shade, with nuts and screws, etc. complete
9.96.2 250x16 each 176 790.30 139,093
Wooden frames-Toilet (Internal Doors)
6.8
9.100
Providing woodwork in frames of doors, windows,
clerestory windows and other frames, wrought framed
and fixed in position and hold fast lugs or with dash
fasteners of requiired dia & length (hold fast and lugs
shall be paid seperately)
9.1.2 Sal wood (Toilet Internal doors) cum 7 75558.60 528,910
Wooden frames-(All other Doors)
6.9
9.100
Providing woodwork in frames of doors, windows,
clerestory windows and other frames, wrought framed
and fixed in position and hold fast lugs or with dash
fasteners of requiired dia & length (hold fast and lugs
shall be paid seperately)
cum 15 91496.00 1,372,440
SUB TOTAL 2,261,173
Signature of EPIL 6 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
7.0 11.000 FLOORING
11.260
Kota stone flooring over 20 mm (average) thick base
laid over and jointed with grey cement slurry mixed
with pigment to match the shade of the slab including
rubbing and polishing complete with base of 1:4 (1
cement : 4 coarse sand)
Note: For detailed specification for Kota stone flooring
refer ACC II
7.1 11.26.1 25 mm thick sqm 895 1141.40 1,021,553
7.1.1
8.600
Mirror polishing on marble work/granite work/stone
work wherever required to give high gloss finish
sqm 895 212.85 190,501
7.2
11.270
Kota stone slabs 20 mm thick in risers of steps, skirting,
dado and pillars laid on 12 mm (average) thick cement
mortar 1:3 (1 cement 3 coarse sand) and jointed with
grey cement slurry mixed with pigment to match the
shade of the slabs, including rubbing and polishing
complete.
sqm 115 1191.25 136,994
7.2.1
8.600
Mirror polishing on marble work/granite work/stone
work wherever required to give high gloss finish
sqm 115 212.85 24,478
0
7.3
11.430
Fixing glazed/ Ceramic / Vitrified floor tiles with
cement based high polymer modified quick-set tile
adhesive ( Water based ) conforming to IS : 15477,
Adhesive per sqm of tile area, in average 3mm
thickness.
sqm 775 432.85 335,459
7.4
11.470
Providing and laying Vitrified tiles in different sizes
(thickness to be specified by the manufacturer), with
water absorption less than 0.08% and conforming to IS:
15622, of approved brand & manufacturer, in all
colours and shade, in skirting, riser of steps, laid with
cement based high polymer modified quick set tile
adhesive (water based) conforming to IS: 15477, in
average 6 mm thickness, including grouting of joints
(Payment for grouting of joints to be made separately).
11.47.2 Size of Tile 60x60 cm sqm 775 1630.20 1,263,405
MIRROR POLISH ON MOSAIC FLOORING
FOR ROOMS AND PASSAGES
7.5
8.600
Mirror polishing on marble work/granite work/stone
work wherever required to give high gloss finish
a Flooring sq.mts 775.00
b Skirting sq.mts 60
835 212.85 177,730
MOSAIC FLOOR TILES
Signature of EPIL 7 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
7.6 11.440 Crazy ceramic tile flooring, with under layer 12 mm
thick cement mortar 1:4 (1 cement: 4 coarse sand), with
joints not exceeding 5 mm, including filling the gaps
with ordinary cement mixture & mixing with
syntheticpolyester fibre, triangular in shape having
specific gravity of 1.34 to 1.40, cross section size
ranging from 10 to 40 micron & length upto 6 mm ,
mixing fibre @ 125 grams per 50 kg of cement in
cement mortar, including providing and mixing water
proofing material in mortar @ 1 kg per 50 kg
of cement , all complete as per direction of Engineer-in-
charge.
sqm 286 467 133,562
SUB TOTAL 3,283,681
8.0 13.000 FINISHING WORK
13.100 12 mm cement plaster of mix: 0
8.1 13.1.1 1 : 4 (1 Cement : 4 fine sand) sqm 2100 163.35 343,035
8.2 13.370 Whitewashing with lime to give an even shade
13.37.1New work (two or more coats) sq.mts 1500 16.20 24,300
8.313.39
Colour washing such as green, blue or buff to give an
even shade
13.39.1New work (two or more coats) with a coat of white
washing with lime
sq.m 625 22.05 13,781
SUB TOTAL 381,116
9.0 21.000 ALUMINIUM WORK
21.100
Providing and fixing aluminium work for doors,
windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections and
other sections of approved make conforming to IS: 733
and IS: 1285, fixing with dash fasteners of required dia
and size, including necessary filling up the gaps at
junctions, i.e. at top, bottom and sides with required
EPDM rubber/ neoprene gasket etc. Aluminium
sections shall be smooth, rust free, straight, mitred and
jointed mechanically wherever required including cleat
angle, Aluminium snap beading for glazing / paneling,
C.P. brass / stainless steel screws, all complete as per
architectural drawings and the directions of Engineer-in-
charge. (Glazing, paneling and dash fasteners to be paid
for separately) :
9.1
21.1.2
For shutters of doors, windows & ventilators including
providing and fixing hinges/ pivots and making
provision for fixing of fittings wherever required
including the cost of EPDM rubber / neoprene gasket
required (Fittings shall be paid for separately)
21.1.2.2Powder coated aluminium (minimum thickness of
powder coating 50 micron)
Kg 150 435.75 65,363
Signature of EPIL 8 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
9.2
21.300
Providing and fixing glazing in aluminium door,
window, ventilator shutters and partitions etc. with
EPDM rubber / neoprene gasket etc. complete as per
the architectural drawings and the directions of engineer-
in-charge. (Cost of aluminium snap beading shall be
paid in basic item):
21.3.2 With float glass panes of 5.50 mm thickness sqm 55 1054.20 57,981
9.3
21.800
Filling the gap in between aluminium frame & adjacent
RCC/ Brick/ Stone work by providing weather silicon
sealant over backer rod of approved quality
as per architectural drawings and direction of Engineer-
in-charge complete.
21.8.1 Upto 5mm depth and 5 mm width metre 60 88.75 5,325
SUB TOTAL 128,669
Signature of EPIL 9 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
10.0 22.000 WATER PROOFING WORK
10.1
22.300
Providing and laying water proofing treatment to
vertical and horizontal surfaces of depressed portions of
W.C., kitchen and the like consisting
of:
(i) Ist course of applying cement slurry @ 4.4 kg/sqm
mixed with
water proofing compound conforming to IS 2645 in
recommended proportions including rounding off
junction of
vertical and horizontal surface.
(ii) IInd course of 20 mm cement plaster 1:3 (1 cement :
3 coarse
sand) mixed with water proofing compound in
recommended proportion including rounding off
junction of vertical and horizontal surface.
(iii) IIIrd course of applying blown or residual bitumen
applied hot at 1.7 kg. per sqm of area.
(iv) IVth course of 400 micron thick PVC sheet.
(Overlaps at joints of PVC sheet should be 100 mm
wide and pasted to each
other with bitumen @ 1.7 kg/sqm).
The rate includes preparation of surface, treatment and
sealing of all joints, corners, junctions of pipes and
masonry with polymer mixed slurry.
sqm 95 522.90 49,676
10.2
22.700
Providing and laying integral cement based water
proofing treatment including preparation of surface as
required for treatment of roofs, balconies, terraces etc
consisting of following operations: a) Applying a slurry
coat of neat cement using 2.75 kg/sqm admixed with
water proofing compound conforming to IS : 2645 and
approved by Engineer-in-charge including laying glass
fibre cloth of approved quality in top layer of plaster
and finally finishing the surface with trowel with neat
cement slurry and making pattern of 300x300 mm
square 3 mm deep. e) The whole terrace so finished
shall be flooded with water for a minimum period of
two weeks for curing and for final test. All above
operations to be done in order and as directed and
specified by the Engineer-in-Charge :
Signature of EPIL 10 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
10.3
22.170
Providing and laying in situr seven course water
proofing treatmen with APP (Atactic Polypropylene)
modified Polymeric membrane over roof consisiting of
first coat of bitument primer @0.40 kg per sq.mt, wnd,
4th and 6th courses of bonding material @1.20kg/sqm,
which shall consist of blown type bitumen of grade
85/25 conforming to IS:702, 3rd and 5th layers of
roofing membrance APP modified Polymeric
membrane 2.0 mm thick of 3.00 kg/sq.mt weight
consisting of five layers prefabricated with centre core
as 100 micron HMHDPE film sandwiched on both
sides with polymeric mix and the polymeric mix and
the polymeric mix is protected on both side with 20
micron HMHDPE film. 7th the top most layer shall be
finished with brick tiles of class designation 10 grouted
with cemen mortar 1:3 (1 cement:3 fine sand) mixed
with 2 per cent integral water proofing compound by
weight of cemen over a 12 mm layer of cemen mortar
1:3 (1 cement:3 fine sand) and finished neat (item of
laying brick tiles shall be papid for separately)
Sqm 230 572.25 131,618
SUB TOTAL 181,293
11.0 STEEL REINFORCEMENT
5.220
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position and
binding all complete upto plinth level.
11.1 5.22.6 Thermo-Mechanically Treated bars Kg. 68.10 0
5.22A
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position and
binding all complete above plinth level.
11.2 5.22A.6 Thermo-Mechanically Treated bars Kg. 72201 68.10 4,916,920
11.3 9.480 M.S. GRILL
Providing and fixing M.S. grills of required pattern in
frames of windows
etc. with M.S. flats, square or round bars etc. including
priming coat with
approved steel primer all complete.
Fixed to steel windows by welding Kg 1320 109.00 143,880
SUB TOTAL 5,060,800
CIVIL WORKS TOTAL 20,383,881
Signature of EPIL 11 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
12.0 ELECTRICAL BOQs
LIGHT FIXTURES
12.1
SOR 2012-13.
(ITEM NO 5-1-
6)
Providing & erecting Approved make Power Saving 50 Watt
1200mm dia Ceiling Fan with double ball bearing ISI mark
with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete
having 3blades with aluminium blades with , canopy & 30 cms.
down rod erected with 24/ 0.2, 3 core flexible wire with
earthing.(Make shall be approved by Engineer in charge))
Nos 46 2070.00 95,220
12.2
SOR 2012-13.
(ITEM NO 5-2-
3)
Supplying & erecting fan hook box of 10 mm M.S. round bar
bounded to the RCC bars up to 50mm length each side and
pierced through a 16 Gauge M.S. box / Heavy Duty PVC box
complete erected concealed in Ceiling with necessary finishing.
Nos 46 125.00 5,750
12.3
SOR 2012-13.
(ITEM NO 5-2-
5)
Providing 2.5mm.thick laminated acrylic sheet to cover the fan
hook or Fan box.Nos 46 20.00 920
12.4
SOR 2012-13.
(ITEM NO 5-2-
1)
Supplying and erecting 19 / 20 mm. nominal bore Medium
Class M.S. Pipe down rod erected duly painted for fan complete
with necessary 24/ O.20, 3 core flexible wire with earthing.
Mtr 44 125.00 5,500
12.5
SOR 2012-13.
(ITEM NO.5-3-
4-A)
Supplying and erecting approved make exhaust fan having size
305mm, 900 RPM. CAT IINos 16 2400.00 38,400
12.6
SOR 2012-13.
(ITEM NO.5-3-
5)
Providing suitable M.S.louver shutter of the Exhaust Fan. Nos 16 430.00 6,880
12.7
SOR 2012-13.
(ITEM NO.5-3-
8)
Providing recess in window frame covering the rei-naining
portion of window frame with 15 mm thick plywood and
colour washing to match the colour of the wall.
Nos 16 200.00 3,200
155,870
13 INTERNAL WIRING
13.1
SOR 2012-13.
(ITEM NO 1-2-
1.)
Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of
1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS
PVC insulated multistrand copper wires, in following type of
pipe to be erected concealed in/ on surface on wall/ceiling
complete with 6A Modular type switch / bell push &
accessories and earth continuity of following type, erected on
PVC / Metallic box, single mounting base frame covered with
textured/metallic front plate modules erected on / in wall /
ceiling as per pipe erected, with necessary Lamp holder/ceiling
rose / H.D.Connector as directed. (a) with medium class Rigid
PVC pipe and accessories. Cat. III
Pt. 182 420.00 76,440
13.2
SOR 2012-13.
(ITEM NO 1-1-
4.)
Point wiring for secondary light point with 2-1.5 sq.mm &
earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV
grade FRLS PVC insulated multistrand copper wires, in
following type of pipe to be erected concealed in / flushed on
wall/ceiling, complete with earth continuity and necessary
connection with primary light with accessories erected on
Metal / PVC box covered with 3 mm thick PC(Polycarbonet) /
Acrylic sheet for open / concealed wiring. with necessary
Lamp holder / ceiling rose / H.D.Connector as directed.(a) with
medium class Rigid PVC pipe and accessories
Pt. 78 100.00 7,800
13.3
SOR 2012-13.
(ITEM NO 1-2-
2.)
Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5
sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC
insulated multistrand copper wires, in following type of pipe to
be erected concealed in / flushed on wall/ceiling complete
with 6A Modular type switch and hum free EME four or more
step type electronic fan regulator with separately mounted and
accessories with earth continuity of following type erected on
PVC / Metallic box, single mounting base frame covered with
textured/metallic front plate modules erected on / in wall /
ceiling as per pipe erected. with necessary ceiling rose /
H.D.Connector as directed. (a) with medium class Rigid PVC
pipe and accessories. Cat. III
Pt. 46 600.00 27,600
13.4
SOR 2012-13.
(ITEM NO 1-2-
4.)
Point wiring for Looped Plug with 6A Modular type switch & 5
pin socket erected on PVC / Metallic box, single mounting base
frame covered with textured / metallic front plate modules
erected on / in wall / ceiling with following type accessories.
Cat. III
Pt. 25 240.00 6,000
TOTAL FOR LIGHT FIXTURES
Signature of EPIL 12 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
13.5
SOR 2012-13.
(ITEM NO 1-2-
6)
Providing following type of Modular Type Accessories
mounted with pvc / metallic box, single mounting base frame
covered with textured / metallic front plate , modules erected
with necessary connection. As desired by Engineer In charge
(1)One No. SP 6 Amp. (2) One No 5 pin plug
Nos 5 300.00 1,500
13.6
SOR 2012-13.
(ITEM NO 1-4-
1)
Mains with 1.1 KV grade FRLS PVC insulated ISI marked
stranded Copper conductor wire in following type of pipe to
be erected concealed in /flushed on wall/ceiling, with 1.5 sq.
mm copper conductor FRLS PVC insulated stranded wire of
green colour for earth continuity of following size (a) with
medium class Rigid PVC pipe and accessories. Cat. III (b) 2 wire
2.5 sq. mm
Rmt. 3000 80.00 240,000
13.7
SOR 2012-13.
(ITEM NO 1-2-
6)
Providing following type of Modular Type Accessories
mounted with pvc / metallic box, single mounting base frame
covered with textured / metallic front plate , modules erected
with necessary connection. As desired by Engineer In charge
(9) 16 Amp. SP one way switch (10) 6/16Amp. Universal
socket
Nos 24 380.00 9,120
13.8
SOR 2012-13.
(ITEM NO 1-4-
2)
Mains with 1.1 KV grade FRLS PVC insulated ISI marked
stranded Copper conductor wire in following type of pipe to be
erected in / on wall / ceiling with 2.5 sq. mm copper conductor
FRLS PVC insulated stranded wire of green colour for earth
continuity of following size (a) with medium class Rigid PVC
pipe and accessories (a) 2 wire 4 sq. mm
Rmt. 1200 110.00 132,000
500,460
14 COMPUTER WIRING
14.1
SOR 2012-13.
(ITEM NO 1-6-
2-B)
Providing & erecting Switch board for Computer or electric
apparatus consisting of following items in single board erected
on PVC / Metal board with 3 mm thick PC (Polycarbonate) /
Acrylic sheet erected as directed
1 no. 6A/16A universal plug-switch combined.
1 nos. 16A Switch
2 nos. 6A 5 pin Plug [B] For Modular Type Accessories CAT III
Nos 48 1140 54,720
54,720
15 DB's/FLOOR PANEL
Supply,Installation, testing and commissioning of Panel
Board as per IS , Technical Specifications & respective
drawings. The unit rate for each item shall include
Supply & delivery of the panels at the site. Shifting of
panels from site store to the suitable location.(If
applicable) Installation of panel in Electric room or
Location suggested by client within campus including
removing packing. Earthing all components, frame etc. to
a common internal earth bar. Supply & fixing all
accessories and supporting structure. Supply and fixing
of M.S. 100 mm. channels for fixing the panels
connection, testing & commissioning. The panels shall be
compatible to BMS whereever shown in the SLD.
Checking of Internal connection and wiring, operation of
switches, starter, MCCB, MCB, relays, contactors etc.
Supply of necessary tools, hardware, testing hardware,
testing equipment etc. Electrical contractor shall carry
out the insulation test at site & all the readings shall be
submitted in duplicate to the consultant or engineer-in-
charge.
TOTAL FOR INTERNAL WIRING
TOTAL FOR COMPUTER WIRING
Signature of EPIL 13 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
15.1
SOR BASED
RATE
ANALYSIS-2
Supply, Installation, Testing & Commissioning of Ground
Floor Main LT Panel-2 as per Description Below.
Nos 1 117000.00 117,000
Incomer : 160A Four Pole MCCB, Thermal Magnetic
Release, S/C, E/F, O/C, 50Hz, 25KABusbar Size : 160A TPN Al., with Insulation Strip, 415V,
50Hz, 25KA Withstanding for 1 Sec
Outgoing :
1) 40/63A FP MCB, 10KA - 10 Nos C curve
2) 63A FP MCCB, 25KA - 2 Nos
15.2
SOR BASED
RATE
ANALYSIS-3
Supply, Installation, Testing & Commissioning of Utility
Panel as per Description Below.
EACH 1 54000.00 54,000
Incomer : 63A Four Pole MCCB, Thermal Magnetic
Release, 25KABusbar Size : 63A TPN Al. with Insulation Strip, 415V,
50Hz, 25KA Withstanding for 1 Sec
Outgoing :
1) 40A FP MCB, 10KA - 4 Nos C curve
2) 32A DP MCB, 10KA - 2 Nos B curve
15.3
SOR BASED
RATE
ANALYSIS-68 Way SS Double Door Three Phase DB
EACH 10 15000.00 150,000
Incomer : 40/63 A FP MCB. 10KA
ELCB : 3 nos of 32/40 A DP ELCB, 30 mA
Outgoing : 18 nos of 6/10/16/20A SP MCB, 10KA
15.4
SOR BASED
RATE
ANALYSIS-5
Supply, Installation, Testing & Commissioning of Single
Phase Distribution Box as per description below
,Specification, Technical Data sheet & IS.
EACH 1 5000.00 5,000
6 Way SS Single Door Type Distribution Box
Incomer : 40A DP ELMCB, 30 Ma
Outgoing : 6 nos of 6/10/16/20A SP MCB, 10KA
326,000
16 LT CABLES AND TERMINATIONS
16.1
SOR 2012-13.
(ITEM NO 4-3-
3-)
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Aluminium conductor for 1.1 KV. to be laid
on wall with necessary clamps or in existing trench / pipe of
following size of cables (E) 3 1/2 core 120 Sq. mm ( 70 Sq.
mm 1/2 core)
Mtr 100 660.00 66,000
16.2
SOR 2012-13.
(ITEM NO 4-3-
3-)
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Aluminium conductor for 1.1 KV. to be laid
on wall with necessary clamps or in existing trench / pipe of
following size of cables (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm
1/2 core)
Mtr 15 220.00 3,300
16.3
SOR 2012-13.
(ITEM NO 4-3-
4-)
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Aluminium conductor for 1.1 KV. to be laid
on wall with necessary clamps or in existing trench / pipe of
following size of cables (d) 4 core 16 Sq. mm
Mtr 80 180.00 14,400
16.4
SOR 2012-13.
(ITEM NO 4-6-
3)
Providing and, fixing heavy duty flange type brass cable gland
with rubber ring for PVC insulated armoured cable complete
with out going tails, insulating tape etc for following size of
cables.(E) 3.5 core 120 Sq. mm
Ea 2 150.00 300
16.5
SOR 2012-13.
(ITEM NO 4-6-
3)
Providing and, fixing heavy duty flange type brass cable gland
with rubber ring for PVC insulated armoured cable complete
with out going tails, insulating tape etc for following size of
cables.(A) 4 core 25 Sq. mm
Ea 2 70.00 140
16.6
SOR 2012-13.
(ITEM NO 4-6-
1)
Providing and, fixing heavy duty flange type brass cable gland
with rubber ring for PVC insulated armoured cable complete
with out going tails, insulating tape etc for following size of
cables.(E) 4 core 16 Sq. mm
Ea 4 50.00 200
16.7
SOR 2012-13.
(ITEM NO 4-7-
1)
Solderless crimping type Aluminium lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner. (H)
120 Sq.mm.
Ea 8 45.00 360
TOTAL FOR DB'S
Signature of EPIL 14 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
16.8
SOR 2012-13.
(ITEM NO 4-7-
1)
Solderless crimping type Aluminium lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner. (D)
25 Sq.mm.
Ea 8 15.00 120
16.9
SOR 2012-13.
(ITEM NO 4-7-
1)
Solderless crimping type Aluminium lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner. (C) 25
Sq.mm.
Ea 16 15.00 240
85,060
17 DATA CABLE
17.1
SOR 2012-13.
(ITEM NO 1-4-
8-C)
Supplying & erecting approved make LAN cable of following
size in existing pipe as per direction CAT - 6 CABLE with
Medium class RIGID PVC PIPES of following size complete to
be erected on/in wall or ceiling erected with necessary PVC
fittings & Junction boxes fixed with adhesive solution & Clamps
with following dia of pipes, in approved manner as directed 25
mm DIA CONDUIT
Rmt. 1200 50.00 60,000
17.2
SOR 2012-13.
(ITEM NO 1-3-
2-B)
Providing and erecting ISI mark Medium class RIGID PVC
PIPES of following size complete to be erected on/in wall or
ceiling erected with necessary PVC fittings & Junction boxes
fixed with adhesive solution & Clamps with following dia of
pipes, in approved manner as directed 25 mm DIA CONDUIT
Rmt. 1200 32.00 38,400
98,400
18 EARTHING
18.1
SOR 2012-13.
(ITEM NO. 3-
14-10-C)
Supplying & erecting in earthpit of minimum bore dia. 225mm
size ASH or approved make Safe Earthing Electrode consisting
Pipe-in-Pipe Technology as per IS 3043-1987 made of
corrosion free G.I.Pipes having Outer pipe dia of 80 mm
having 80-200 Micron galvanising, Inner pipe dia of 40 mm
having 200-250 Micron galvanising, connection terminal dia of
14 mm with constant ohmic value surrounded by highly
conductive compound with high charge dissipation suitable for
following type of applications. [C] For Electrical Installation
covering Transformer Neutrals, Lightning arrester Earthing,
A.C.Plant & Sensitive Computer System(like Automation,
SCADA)i.e. independent Earthing located in other than
normal soil i.e. Soft Rock, Marshy Soil etc..
-Length of Pipe : 3 Mtrs.
-Back filling Compound :2 nos Bags of 25 Kg.
NOS 2 16500.00 33,000
18.2
SOR 2012-13.
(ITEM NO. 3-
14-5)
Supply and laying of Earthing Conductor Providing and
erecting HOT Deep Galvanised Strip iron wire 8 to 16 S.W.G.KG 25 90.00 2,250
18.3
SOR 2012-13.
(ITEM NO. 3-
14-2)
Supply,laying and jointing of 25 X 6 MM GI Strip KG 30 90.00 2,700
37,950
SUB TOTAL-ELECTRICAL 1,258,460
19.0 Plumbing BOQs
COLD / HOT /DRINKING WATER SUPPLY:
INTERNAL/EXTERNAL WATER SUPPLY
WORK:- Providing,laying and jointing in true
line and level U.P.V.C pipe (SCH-40) of
following dia. Including fittings of standard make
as approved by engineer-in-charge. Pipe shall be
fixed on the wall with the help of clamp at every
2000 mm center to center or shall be concealed as
directed including necessary fittings etc. testing of
pipe and joints and fixing the same with adhesive
solvent, including cost of all materials.
a) 15 mm
Rmt 26 85.00 2,210
b) 25 mm Rmt 50 102.00 5,100
SOR
2013-14
Item No -
0.0
19.1
TOTAL FOR DATA CABLES
TOTAL FOR EARTHING
TOTAL FOR LT CABLES
Signature of EPIL 15 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
c) 32 mm Rmt 16 135.00 2,160
d) 40 mm Rmt 24 169.00 4,056
E) 50 mm Rmt 0 217.00 0
Supplying & erecting resin bonded flap rock wool
/ glass wool with conductivity value 1.67 sq.mm
per watt & to with stand the temp. to 100 degree
centigrade C thickness 50mm with G I pipe of
following size dia "B" class as per IS:1239. The
plastic sheet to be used as covering of glass wool.
Al. cladiy besides other materials like chicken
mesh, 26 G Al. Sheet shall be used for cladding
the insulation pipe.
[A] 20 mm NB pipe
Rmt 0 360.00 0
[B] 25 mm NB pipe Rmt 20 440.00 8,800
[C] 32 mm NB pipe Rmt 0 530.00 0
[D] 40 mm NB pipe Rmt 0 620.00 0
19.3
SOR
2013-14
Item No -
00
Providing and Laying & Jointing in true line
level 110 diameter U.P.V.C (Type'B')
conforming to IS13592-1992 with one end plain
and other end socketed with rubber ring, and
fittings conforming to ISI 14735-1999 of
approved make for drinage system pipe line, pipe
shall be jointed with each other with rubber
lubricant,pipe shall be fixed on wall using of PVC
clamp of the size 110 mm diametre x210 mm
length x 196 mm height at every 2000 mm center
to center or shall be concealed in walls as directed
including testing of pipes and joints and jointed
with adhesive solvant cement including cost of all
materials.
(i) 110 mm Dia(DOWNTAKE FOR SOIL
WATER AND RAIN WATER)
Rmt 71 526.00 37,556
19.4
SOR
2013-14
Item No -
00
Providing and Laying & Jointing in true line
level 110 diameter U.P.V.C (Type'B')
conforming to IS13592-1992 with one end plain
and other end socketed with rubber ring, and
fittings conforming to ISI 14735-1999 of
approved make for drinage system pipe line, pipe
shall be jointed with each other with rubber
lubricant,pipe shall be fixed on wall using of PVC
clamp of the size 110 mm diametre x210 mm
length x 196 mm height at every 2000 mm center
to center or shall be concealed in walls as directed
including testing of pipes and joints and jointed
with adhesive solvant cement including cost of all
materials.
(iii) 160 mm Dia(DOWNTAKE FOR SOIL
WATER AND RAIN WATER)
Rmt 16 948.00 15,168
19.5Providing & fixing in position cowl vent to pipes
a) 75 mm dia
Each 5 431.00 2,155
19.5.1 100 mm dia Each 2 584.00 1,168
19.2
SOR
2013-14
Item No -
0.0
ELECTRIC
AL SOR
2012-13
ITEM NO.
8-11-8
SOR
2013-14
Item No -
19.1
Signature of EPIL 16 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
19.6
SOR
2013-14
Item No -
23.87
Providing and fixing PVC SWR Nahni trap IS
14735 for drain - 100 mm diameter with jali of
the following nominal diameter of self cleansing
design with C.I. scread down or hinged grating
including the cost of cutting and making good the
walls
Each 43 453.00 19,479
19.7
SOR
2013-14
Item No -
23.112
Providing and fixing wash down water closet
(European type, WC pan) with integral S trap
including jointing the trap with soil pipe in cement
mortar 1:1 (1 Cement : 1 fine sand) ( Seal and
cover to be measured and paid for separately) A)
vitrious china white colour
(Cera-2008B / Parryware-C0287 / Hindware-
20011)
Each 17 1043.00 17,731
19.8P & F Flush Cock / Flush Valve (IS : 9758
Mark) for WC of approved quality make :
` CP brass push type 15mm nominal bore.
(-do-) 20mm nominal bore.
(-do-)exposed 25mm nominal bore.
(-do-) 32mm nominal bore.
(-do-) concealed 25mm nominal bore.
SOR
2013-14
Item No -
2.14.6
(-do-) concealed 32mm nominal bore. Each 17 1716.00 29,172
19.9
SOR
2013-14
Item No -
23.121
Providing and fixing plastic seat and cover for
wash down water closet with C.P. brass hinges
and rubber buffers A) Black plastic seat and cover
(Cera-2308 / Parryware-C8071 / Hindware-
20011)
Each 17 397.00 6,749
19.10
SOR
2013-14
Item No -
23.127
Providing and fixing wash basin with single hole
for pillar trap with CI or MS brackets painted
white including cutting holes and making good the
same but excluding fitting a) Vitreous
china flat back wash basin 550mm X 400mm size
in white colour
(Cera-1008/ Parryware-C0477 / Hindware-)
Each 12 1058.00 12,696
19.11
SOR
2013-14
Item No -
23.134
Providing and fixing rubber plug for sink or
wash basin.
Each 12 22.00 264
19.12
SOR
2013-14
Item No -
23.136
Providing and fixing M.I. fisher union for wash
basin or sink.
(A) 32 mm dia.
Each 12 103.00 1,236
19.13
SOR
2013-14
Item No -
23.143
Providing and fixing 600mmX450mm bevelled
edge mirror of superior glass mounted on 6mm
thick A.C. sheet or plywood sheet and fixing to
wooden plug with C.P. brass screws and washers.
Each 12 690.00 8,280
Signature of EPIL 17 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
19.14
SOR
2013-14
Item No -
23.146
Providing and fixing toilet paper holder
(A) C.P. Brass
(Cera- / Parryware- / Hindware)
Each 17 456.00 7,752
19.15
SOR
2013-14
Item No -
23.122
Providing and Fixing Urinal of approved quality
including connecting the Urinal with waste pipe,
tap etc. completed.
[A] White earthenware flat back or corner type
size 430mmX 260mm X 350mm
(Cera-5001 / Parryware-C0501 / Hindware-
60005)
Each 0 783.00 0
19.16
SOR
2013-14
Item No -
0.0
Providing erecting and fixing double coated sintex
or equivalent PVC.(ISI) water tank of required
capacity each with all necessary fittings and
connection etc. complete on terrace.
Liter 5000 4.60 23,000
19.17
SOR
2013-14
Item No -
0.0
Providing and fixing ball cock of approved
quality as directed
(I)40 mm dia
Each 0 261.00 0
19.18
SOR
2013-14
Item No -
0.0
Providing and fixing ball cock of approved
quality as directed
(II)32 mm dia
Each 8 261.00 2,088
19.19
SOR
2013-14
Item No -
0.0
Providing and fixing ball cock of approved
quality as directed
(III)25 mm dia
Each 5 261.00 1,305
Providing and Laying & Jointing in true line
level Following diameter U.P.V.C (Type'B')
conforming to IS13592-1992 with one end plain
and other end socketed with rubber ring, and
fittings conforming to ISI 14735-1999 of
approved make for drinage system pipe line, pipe
shall be jointed with each other with rubber
lubricant,pipe shall be fixed on wall using of PVC
clamp of the size 160 mm diametre x210 mm
length x 196 mm height at every 2000 mm
center to center or shall be concealed in walls as
directed including testing of pipes and joints and
jointed with adhesive solvant cement including
cost of all materials.
(i) 110 mm dia.
Rmt 80 526.00 42,080
[ii] 160 mmDia. Rmt 50 948.00 47,400
Providing and laying Cement concrete 1:5:10 (1-
Cement : 5 - fine sand : 10-Graded stone
aggregate 40mm nominal size) bedding for
stoneware pipes of following internal diameters
with necessary formwork and curing complete.
[A] 100mm dia. (112 mm Ave. bed thickness)
Rmt 80 118.00 9,440
[B] 150mm dia. (166mm Ave. bed thickness)Rmt 50 199.00 9,950
19.22
SOR
2013-14
Item No -
24.19
Providing and fixing S.W. gully trap with C.I.
grating brick masonry chamber and water tight
C.I. cover with frame of 300mmX300mm size
(inside) with standard weight. I) Square mouth
traps.
a) 100mmX100mm size P type
Each 4 1432.00 5,728
19.20
19.21
SOR
2013-14
Item No -
0.0
SOR
2013-14
Item No -
24..2
Signature of EPIL 18 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
Constructing Manhole with R.C.C. top slab in
1:2:4 mix (1-cement : 2-coarse send : 4-graded
stone aggregate 20mm nominal size) foundation
concrete 1:3:6 mix (1-cement : 3-coarse sand : 6-
Brick bats 40 + 50mm size) inside plastering
15mm thick with Cement a) With 230mm
thick walls of brick masonary using brick having
crushing strength not less than 35Kg. / Sq.cm. in
Cement Mortar 1:5 (1- Cement : 5- Coarse sand)
(I) Inside size 900mm X 1200mm and 1.5M. deep
including C.I. cover with frame size 560mm
diameter total weight of cover and frame to be not
less than 128 kgs. (Wt. of cover 64 kg. and Wt. of
frame 64 Kg.)
1) A type depth 0.90 Meter for 150 mm diameter
sewer.
Each 4 11609 46,436
2) B type depth 1.5 Meter for 150 mm diameter
sewer.
Each 1 20019.00 20,019
3) B type depth 2.24 Meter for 150 mm diameter
sewer.
Each 0 23518.00 0
Providing & Laying ( to level or Slope) and
jointing reinforced concrete Light Duty NoN
Pressure I.S. Class NP2 of the following internal
diameter with collars and butt ends prepared for
collar joints including testing of joints for
[B]250 mm dia
Rmt 10 414.00 4,140
[C]300 mm dia Rmt 0 523.00 0
19.24
ELECTRIC
AL SOR
2012-13
ITEM NO.
9-4-2 (F)
For 5 HP 3 phase open well horizontal mono
block pump set suitable for 150 LPM to 500
LPM @ 15 to 30 Mtr head. CAT-II (1W +1S)
with necessary valve fittings.
Each 1 54650.00 54,650
19.25
ELECTRIC
AL SOR
2012-13
ITEM NO.
9-5-6 (B)
Supplying and erecting approved make3 phase
motor control panel (ATS) made from 16 G.
CRCA sheet duly painted with epoxy power paint
inside and outside with hinged doors and locking
arrangement, consisting, of suitable switch of AC
23 duty with HRC fuses (Cat.III), starting and
running contactors, overload relay, Automatic
water level controller, Electronic timer with
master timer CT operated Ammeter with selector
switch, Voltmeter with selector switch, phase
indicating lamps, single phasing preventer , water
level guard, over load, start, run and stop push
buttons, air cooled auto transformer with 60%,
70%, 80% tapping, Panel to be erected on angle
iron frame grouted on wall as directed., contactors
relays, timer etc. shall be of L & T Siemens /
Cutler Hammer make.
(b) Suitable for 5 H.P.
Each 1 40250.00 40,250
19.22
19.23
SOR
2013-14
Item No -
24.27
SOR
2013-14
Item No -
24.22
Signature of EPIL 19 Signature of BIdder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR.
NO.DSR 2014
ITEM NO.
DESCRIPTION UNIT QTY RATE AMOUNT
19.26
ELECTRIC
AL SOR
2012-13
ITEM NO.
8-8-2
Providing & erecting water cooler having storage
capacity 150 Ltr. & cooling capacity 80 Ltr.per
hour @ an ambient temp of 45 deg C. The outlet
temp. of the water should drop by 15 deg C within
a hour, The water cooler should be comprising of
hermetically sealed compressor, fan motor,
condensing unit, water tank surrounded by
evaporating, coil, thermostats, relay etc.complete
with necessary inlet & outlet connection. The
body of water cooler will be made from Stainless
Steel.
Each 1 54000.00 54,000
19.27
ELECTRIC
AL SOR
2012-13
ITEM NO.
8-8-6
Supplying & erecting 5 stage single reverse
osmosis(R.O.) water purification system with
M.S. powder coated frame, prefilter housing with
'O' ring presediment filter GAC filter, carbon filter
suitable buster DC pump capacity 80 psi, mention
with 40 Osg inline type post carbon filter auto low
& high pressure switches with following size of
storage tank & LPH capacity & erected as directed
with one year comprehensive maintenance
guarantee.
[C] 50 Ltr / Hr with 250 psi 2 nos booster
pump
Each 1 27000.00 27,000
SUB TOTAL-PLUMBING 569,218
Signature of EPIL 20 Signature of BIdder
PART A
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
Summary NON DSR Works
1.0 Exposed Brick Work 1795500.00
2.0 Exposed Concrete Work 1489540.00
3.0 Flooring (Deleted) 0.00
4.0 Miscelleneous Work 570950.00
5.0 FURNITURE (Deleted) 0.00
6.0 Elevator 4,000,000
7.0 CCTV Works 75000
8.0 Plumbing Work 169,329
9.0 Electrical Work 483,350
TOTAL 8583669.00
PART-II-NON-DSR ITEMS FOR CIVIL WORK, ELECTRICAL, PLUMBING AND
SPECIALISED E&M WORKS
Signature of EPIL 20 Signature of Bidder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR. NO. DESCRIPTION FURNITURE (Deleted)QTY RATE AMOUNT
1.0 EXPOSED BRICK WORK
1.1
Brick work with common burnt clay machine moulded modular bricks of
class designation 12.5 in exposed brick work including raking horizontal and
vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1
cement : 6 coarse sand) whilst the mortar is green in bond pattern as
specified. The mortar to be pressed with special steel trowels. The joints of
the pointed work shall be neat. The lines will be regular and uniform in
breadth and the joints shall be raised, flat, sunk or 'V' shaped as directed. No
false joints allowed.
sq.mts. 525 3300.00 1,732,500.00
1.2Waterproofing coating on brick cladding to prevent efflorescence (Dr.Fixit or
equivalent)
sq.mt 525 120.00 63,000.00
SUB TOTAL 1,795,500.00
2.0 EXPOSED CONCRETE WORK
FORMWORK
2.1Walls (any thickness) including attached pilasters, buttresses, plinth and string
courses etc.
Sqm 220 650.00 143,000.00
2.2 Suspended floors, roofs, landings, balconies and access platform. Sqm 1100 650.00 715,000.00
2.3 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 750 650.00 487,500.00
2.4 Columns, Pillars, Piers, Piers, Abutments, Posts and Struts. Sqm 90 650.00 58,500.00
2.5 Stairs (excluding landings) except spiral stair-cases Sqm 60 650.00 38,740.00
2.6 Edges of slabs and breaks in floors and walls.
Below 20 cm wide rmt 360 130.00 46,800.00
SUB-TOTAL 1,489,540.00
3.0 FLOORING
Deleted
Total Flooring
Client : NATIONAL INSTITUTE OF DESIGN
Executing Agency: Engineering Projects India Ltd. (EPIL)
Architect: R T & ASSOCIATES PVT LTD.
Project Name: New Girls Hostel building, Ahmedabad
PART-II-BOQ FOR CIVIL WORK, ELECTRICAL, PLUMBING AND SPECIALISED E&M WORKS (NON-DSR ITEMS)
Signature of EPIL 21 Signature of Bidder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR. NO. DESCRIPTION FURNITURE (Deleted)QTY RATE AMOUNT
4.0 MISCELLENEOUS
MOSQUITO SCREEN FOR WINDOWS
Fixing sliding mosquito nets with aluminium section frames 2.5mm thick and
Saint Gobain or equivalent fiber net with roller mechanism for all windows
and ventilators
sqm 55 2250.00 123,750.00
4.1 Anodised aluminium fixed louvered screens for the duct shafts
Aluminum plain panels with finish of powder coating on the visible surface
of approved colour and supporting structure black colour spray painted
(Supersil or equivalent make)
sqm 100 2200.00 220,000.00
4.2 FLUSH DOORS (FOR TOILET)
30mm thick pine frame pine filler doors
PF bonded resin waterproof ISI brand with 1.00 mm thick super gloss
laminate on both sides and teak wood borders on the shutters on all four sides
60 2400 144,000.00
4.3Supplying and filling in plinth with river sand under floors, including
watering, ramming, consolidating and dressing complete.
cum 104 800.00 83,200
Total of Miscellenous 570,950.00
5.0 FURNITURE
Deleted
6.0 ELEVATORS
Machine room less 6 passenger elevator with 408 kg capacity and 1.00m/s
speed (Otis or equivalent)
2 2000000 4,000,000.00
7.0 CCTV
Supplying, testing, installation and commissioning of IP based CCTV system
for building security comprising of PTZ, fixed camera, cabling, recording,
display system and hardware and software support Including one Computer
at Reception
LS 75,000.00
8.0 PLUMBING WORK
8.1
Providing and Laying & Jointing in true line level 75 diameter
U.P.V.C (Type'B') conforming to IS13592-1992 with one end plain
and other end socketed with rubber ring, and fittings conforming to
ISI 14735-1999 of approved make for drinage system pipe line, pipe
shall be jointed with each other with rubber lubricant,pipe shall be
fixed on wall using of PVC clamp of the size 75 mm diametre x210
mm length x 196 mm height at every 2000 mm center to center or
shall be concealed in walls as directed including testing of pipes and
joints and jointed with adhesive solvant cement including cost of all
materials.
(i) 75 mm Dia(DOWNTAKE FOR SOIL WATER AND RAIN
WATER)
Rmt 149 350.00 52,150
8.2
Providing and fixing C.P Health Faucet with 1 meter flexible pipe
and wall hook approved make. The fixing include drilling &
installation of wooden plug with C.P. brass screw with making the
wall good with finishes as per instruction of Engg. In charge etc.
complete.
(Cera-CG205/ Parryware-T9937A1 / Hindware-F160027)
Each 17 435.00 7,395
8.3
Providing and fixing Angle Cock with screw, back nuts all necessary
fittings etc. Completed
(Cera-CM108/ Parryware-T9939A1 / Hindware-F100043)
Each 12 476.00 5,712
8.4
Providing and fixing 32 mm dia C.P. brass waste for wash basin or
sink.
(Cera- / Parryware-T9911A1 / Hindware-)
Each 12 180.00 2,160
8.5
Providing and fixing Chromium plated bottle trap with necessary
coupling of approved quality for wash basin.
(Cera-CM104 / Parryware-T3201A1 / Hindware-E850015)
Each 12 891.00 10,692
8.6
Supply installation testing and commisioning of HAND OPERATED
1.1 LITER CAPACITY soap dispenser, Push-Button type,
White/smoked. Cover in ABS Thermoplastic body.
(Cera-CA211 / Parryware-T3201A1 / Hindware)
Each 12 1285.00 15,420
Signature of EPIL 22 Signature of Bidder
CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS
SR. NO. DESCRIPTION FURNITURE (Deleted)QTY RATE AMOUNT
8.7
Providing and fixing CP brass towel rail complete with C.P. brass
brackets fix to wooden plug with CP brass screws. I) 600 mm X 20
mm
(Cera-CA303 / Parryware-T6001A1 / Hindware-F880005)
Each 10 900.00 9,000
8.8
Providing and fixing of screwed down bib taps of following size
(A) Brass chromium plated screw down bib tap of 20mm
(Cera-CC103 / Parryware-T3504A1 / Hindware-F200003)
Each 53 608.00 32,224
8.9
Providing and fixing C.P. brass overhead shower with 15 mm or 20
mm inlet Arm
(A)100 mm dia.
(Cera-CH102,CG416A/Parryware-G0132A1,T9901A1/
Hindware-F160039)
Each 16 845.00 13,520
8.10
Providing and fixing concealed Stop cock for overhead shower
consisting of fitting sleeve, operating lever and adjustable wall flange
of approved quality and of 1/2" size as directed below
(Cera-CC127 / Parryware- / Hindware)
Each 16 860.00 13,760
8.11
Providing and fixing pillar tap capstan head screw down high
pressure with screw and back nuts of (I)15mm Dia.
(Cera-CC101 / Parryware-T3501A1 / Hindware-F200001)
Each 12 608.00 7,296
169,329
ELECTRICAL WORK
9.0 LIGHT FIXTURES
9.1
Supply, Installation, Assembling, Testing & Commissioning of 18W T-5 LED Wall/Surface
mounted complete with driver and LED suitable for 100w/Lumerns with all necessary
accessories to complete the installation Satisfactorily.
Nos 112 1300.00 145,600
9.2
Supply, Installation, Assembling, Testing & Commissioning of 9W LED Bracket light Wall
mounted complete with driver and LED suitable for 100w/Lumerns with all necessary
accessories to complete the installation Satisfactorily.
Nos 81 1050.00 85,050
9.3
Supply, Installation, Assembling, Testing & Commissioning of 14W LED Study (Mirror)
light Wall mounted complete with driver and LED suitable for 100w/Lumerns with all
necessary accessories to complete the installation Satisfactorily.
Nos 60 750.00 45,000
DATA CABLE
9.4
Supply and Installation of Layer 2/3 manageable switch, 24 x 10/100Mbps 802.3a/f PoE
ports, auto MDI/MDX, auto-sensing, supporting minimum 2 nos. 1000Mbps Copper or
ofc shared ports for uplinks.
Nos 2 22100.00 44,200
9.5Supplying,installtion,testing & commsissioning of 6U Network rack with base support. Each 1 5600.00 5,600
9.6
Supplying,installtion,testing & commsissioning of 2 Core OM3 Multimode Mode
Fiber Armoured cable complete with using Fusion splicing with pre-terminated
LC pigtails, dressing and proper fixing into rolosplice trays and coupler as
required complete with termination.
Rmt 100 170.00 17,000
9.7
Supply, Installation, testing & commisioning of Wire less WiFi Router with below
specification Networking Interface : (1) 10/100 Ethernet Port Buttons : Reset Antennas :
2 Integrated (Supports 2x2 MIMO with Spatial Diversity)Wi-Fi Standards : 802.11
b/g/n*Power Method : Passive Power over Ethernet (12-24V) Power Supply : Included
24V, 0.5A PoE Adapter Maximum Power Consumption : 6 W Maximum TX Power : 27
dBm BSSID : Up to Four Per Radio Power Save : Supported Wireless Security : WEP, WPA-
PSK, WPA-TKIP,WPA2 AES, 802.11i Certifications : CE, FCC, IC Mounting : Wall/Ceiling
(Kits Included) Operating Temperature : 10 to 70° C Operating Humidity : 5 - 80%
Condensing Supported :WMM, Voice, Video, Best Effort, and Background 'Concurrent
Clients 50+ Supported Data Rates (Mbps) Data Rates:802.11n, 6.5 Mbps to 300 Mbps
(MCS0 - MCS15, HT 20/40 802.11b, 1, 2, 5.5, 11 Mbps 802.11g, 6, 9, 12, 18, 24, 36, 48, 54
Mbps Frequency : 2.4 GHz WITH SOTWARE FOR CONTROL
Each 18 6500.00 117,000
External Routing Network
9.8Supply, Installation, Assembling, Testing & Commissioning of 200mm Dia RCC Hume Pipe
for External Cable LayingRmt 50 145.00 7,250
9.9Supply, Installation, Assembling, Testing & Commissioning of 100mm Dia RCC Hume Pipe
for External Cable LayingRmt 50 205.00 10,250
9.10
Supply, Installation, Assembling, Testing & Commissioning of 600mm x 600mm (Inner
Size)x 1000mm deep Electrical Manhole with External wall of 150mm Thick complete
with required accessories as per Structural Details
Each 4 1600.00 6,400
SUB TOTAL-ELECTRICAL 483,350
GRAND TOTAL-PART-II 8,583,669.00
SUB TOTAL PLUMBING-NON DSR WORKS
Signature of EPIL 23 Signature of Bidder