drawing index - manitoba · drawing index company project project number location ... asme pressure...
TRANSCRIPT
DRAWING INDEX
Company
Project
Project Number
Location
Revision
Date
Drawing No. Client No. Description Date Revision
12069COVER
WESTVIEW PIPING MATERIAL SPECIFICATION - B2 CLASS 300 CARBON STEEL LOW TEMP SWEET 25-Oct-12 3
WESTVIEW PIPING MATERIAL SPECIFICATION - D2 CLASS 900 CARBON STEEL LOW TEMP SWEET 25-Oct-12 3
12069-SYM-001 TYPICAL SYMBOLOGY SHEET 4-Jan-13 0
10001-PID-005 LSD 09-32-001-28 W1M SALES OIL TANKS AREA PIPING AND INSTRUMENTATION DIAGRAM 4-Jan-13 5
12069-PID-001 LSD 09-32-001-28 W1M LACT SKID AREA PIPING AND INSTRUMENTATION DIAGRAM 4-Jan-13 A
12069-PID-002 LSD 09-32-001-28 W1M SALES OIL PUMP AREA PIPING AND INSTRUMENTATION DIAGRAM 4-Jan-13 A
12069-PID-003 LSD 09-32-001-28 W1M COMPRESSOR AREA PIPING AND INSTRUMENTATION DIAGRAM 4-Jan-13 A
12069-PID-004 LSD 14-36-001-28 W1M EOG TIE-IN RISERS AREA PIPING AND INSTRUMENTATION DIAGRAM 4-Jan-13 A
January 4, 2013
LEGACY OIL & GAS INC.
PIERSON PIPELINE TO EOG
12069
VARIOUS LSD
ISSUED FOR APPROVAL
1 07/01/2013
PIPING SPECIFICATION B2 REV 3 – OCTOBER 25, 2012 PAGE 1 OF 1
PIPING MATERIAL SPECIFICATION B2
SERVICE
Sweet Hydrocarbon Process, Fuel Gas, Instrument Air, Glycol, LP Flare Systems, Process Vents & Drains
Design Code B31.3
Pipe Material Carbon Steel
ASME Pressure Class 300 (PN 50)
Corrosion Allowance 1.5 mm
Non Destructive Testing (NDT) 100% visual, 5% Radiography (RT), Note 1
Post Weld Heat Treatment > 19.1 mm WT, Per Code
Branch Connection Chart Table 1
Pressure Temperature Limits Based upon flange limit design
°C kPag °F psig
-45 to 38 5102 -49 to 100 740
38 to 93 4654 100 to 200 675
PIPE
Component Size NPS Ends Sch Description Notes
Pipe ½ to ¾
1 to 2 2 to 16
PE, THRD
PE, THRD BE
160
80 40
ASTM A333 Gr. 6 SMLS
ASTM A333 Gr. 6 SMLS ASTM A333 Gr. 6 SMLS
8
3, 8 8
COMPONENTS
Component Size NPS Ends Sch Class Description Notes
Blind Flange 2 to 16 RF - 300 ASTM A516 Gr. 70N 4, 9
Cap ½ to 2
2 to 16
THRD
BW
-
40
3000
-
ASTM A350 LF2 Cl. 1
ASTM A420 Gr. WPL6
3, 10
11
Coupling ½ to 2 THRD - 3000 ASTM A350 LF2 Cl. 1, Full & Half 3
Cross ½ to 2 SW, THRD - 3000 ASTM A350 LF2 Cl. 1 3, 10
Elbow ½ to 2
2 to 16
SW, THRD
BW
-
40
3000
-
ASTM A350 LF2 Cl. 1, 45º & 90º
ASTM A420 Gr. WPL6, 45º & 90º, Str, Red
3, 10
11
Elbolet ½ to 2 THRD - 3000 ASTM A350 LF2 Cl. 1 3, 12
Flange ½ to 2 2 to 16
RFSW,RFTHRD RFWN
3000 40
300 300
ASTM A350 LF2 Cl. 1 ASTM A350 LF2 Cl. 1
3, 4, 13 4, 13
Gasket 2 to 16 RF - 300 Spiral Wound c/w flexible graphite filler and s/s windings to ASME B16.20
14
Nipple ½ to ¾
1 to 2
PE, THRD
PE, THRD
160
80
-
-
ASTM A333 Gr. 6 SMLS, 100 mm long min
ASTM A333 Gr. 6 SMLS, 100 mm long min
9
3, 9
Orifice Flange 2 to 12 RFWN 40 300 ASTM A350 LF2 Cl. 1, c/w ½” NPT taps 4, 15
Plug ½ to 2 ½ to 2
THRD THRD
160 -
- 3000
ASTM A350 LF2 Cl. 1, Bull ASTM A350 LF2 Cl. 1, Hex Head
3 3
Reducer 2 to 16 BW 40 - ASTM A420 Gr. WPL6, Conc, Ecc 14
Sockolet ¾ to 1-½ SW - 3000 ASTM A350 LF2 Cl. 1 15
Studs & Nuts ALL - - - ASTM A193 Gr. B7, Continuous Thread
ASTM A194 Gr. 2H, 2 Nuts per Stud
Swage ½ to 2 SW, THRD - 3000 ASTM A350 LF2 Cl. 1 3, 16
Tee ½ to 2 2 to 16
SW, THRD BW
- 40
3000 -
ASTM A350 LF2 Cl. 1 ASTM A420 Gr. WPL6
3, 10 11
Threadolet ½ to 2 THRD - 3000 ASTM A350 LF2 Cl. 1 3, 12
Union ½ to 2 SW, THRD - 3000 ASTM A350 LF2 Cl. 1 3, 17
Weldolet 2 to 6 BW 40 - ASTM A350 LF2 Cl. 1 12
TUBING
Component Size (OD) Ends Minimum Wall Thickness Description Notes
Tubing
¼
½ ¾ 1
PE
PE PE PE
0.035”
0.049” 0.065” 0.083”
ASTM A312 316 SS SMLS
ASTM A312 316 SS SMLS ASTM A312 316 SS SMLS ASTM A312 316 SS SMLS
24
24 24 24
VALVES
Component Size NPS
Ends Class Body Trim Type Port Operator Notes
Ball ½ to 2 2 to 8
10 to 16
THRD RF
RF
2000 300
300
ASTM A350 LF2 Cl. 1 ASTM A352 Gr. LCC
ASTM A352 Gr. LCC
Cr PL, TFE Cr PL, TFE
Cr PL, TFE
Split / Floating Split / Floating
Split / Trunnion
RP RP, FP
RP, FP
Lever Lever
Gear
3, 18 5, 19
5, 23
Check ½ to 2 2 to 4
2 to 16
SW,THRD RF
RF
800 300
300
ASTM A350 LF2 Cl. 1 316 SS
ASTM A352 Gr. LCC
Trim #8 Trim #8
Trim #8
Piston / Bolted Non-Slam / Wafer
Swing / Bolted
RP RP
RP, FP
- -
-
3, 21 6, 23
7, 22
Gate ½ to 2 2 to 8
10 to 16
THRD RF
RF
800 300
300
ASTM A350 LF2 Cl. 1 ASTM A352 Gr. LCC
ASTM A352 Gr. LCC
Trim #8 Trim #8
Trim #8
OS&Y / Bolted OS&Y / Bolted
OS&Y / Bolted
RP RP, FP
RP, FP
Hand Wheel Hand Wheel
Gear
3, 21 7, 22
7, 22
Globe ½ to 2 2 to 6
THRD RF
800 300
ASTM A350 LF2 Cl. 1 ASTM A352 Gr. LCC
Trim #8 Trim #8
OS&Y / Bolted OS&Y / Bolted
- -
Hand Wheel Hand Wheel
3, 21 22
Needle ¾ x ½ FNPT x
MNPT 6000 316 SS / 316L SS 316 SS /TFE/V - - - 23
NOTES:
1. Percentage of all butt welds for each welder to be 100% radiographed.
2. All pipe threads shall be in accordance with ASME B1.20.1. 3. NPS 2 threaded piping to be used at the discretion of the stamping engineer. 4. Flange face finish shall be Ra 3.2 to 6.3 μm.
5. FP valves to be used in lines that are to be pigged, in flare systems, for block valves on PSVs and on pump suctions that are NPSH critical. 6. For use on compressor discharge and high pressure pump discharge applications. 7. FP valves for use in lines that are to be pigged.
8. ASME B36.10 9. ASME B16.48 10. ASME B16.11 11. ASME B16.9
12. MSS SP-97 13. ASME B16.5 14. ASME B16.20
15. ASME B 16.36 16. MSS SP-95 17. MSS SP-83
18. MSS SP-110 19. API 608 20. API 609
21. API 602 22. API 600 23. Manufacturer’s Standard
24. ASTM A269
PIPING SPECIFICATION D2 REV 3 – OCTOBER 25, 2012 PAGE 1 OF 1
PIPING MATERIAL SPECIFICATION D2
SERVICE
Sweet Hydrocarbon Process, HP Flare Systems, Process Vents & Drains
Design Code B31.3
Pipe Material Carbon Steel
ASME Pressure Class 900 (PN 150)
Corrosion Allowance 1.5 mm
Non Destructive Testing (NDT) 100% visual, 100% Radiography (RT), Note 1
Post Weld Heat Treatment > 19.1 mm WT, Per Code
Branch Connection Chart Table 1
Pressure Temperature Limits Based upon flange limit design
°C kPag °F psig
-45 to 38 15306 -49 to 100 2220
38 to 93 13962 100 to 200 2025
PIPE
Component Size NPS Ends Sch Description Notes
Pipe
½ to 1-½
½ to 1-½ 2 to 3 4 to 16
PE, THRD
PE, SW BE BE
XXS
160 80
120 (min)
ASTM A333 Gr. 6 SMLS
ASTM A333 Gr. 6 SMLS ASTM A333 Gr. 6 SMLS ASTM A333 Gr. 6 SMLS
7
7 7 7
COMPONENTS
Component Size NPS Ends Sch Class Description Notes
Blind Flange 2 to 16 RF - 900 ASTM A516 Gr. 70N 3, 8
Cap ½ to 1-½ 2 to 3
4 to 16
THRD BW
BW
- 80
120 (min)
6000 -
-
ASTM A350 LF2 Cl. 1 ASTM A420 Gr. WPL6
ASTM A420 Gr. WPL6
9 10
10
Coupling ½ to 1-½ THRD - 6000 ASTM A350 LF2 Cl. 1, Full & Half
Cross ½ to 1-½ SW, THRD - 6000 ASTM A350 LF2 Cl. 1 9
Elbow
½ to 1-½
2 to 3 4 to 16
SW, THRD
BW BW
-
80 120 (min)
6000
- -
ASTM A350 LF2 Cl. 1, 45º & 90º
ASTM A420 Gr. WPL6, 45º & 90º, Str, Red ASTM A420 Gr. WPL6, 45º & 90º, Str, Red
9
10 10
Elbolet ½ to 1-½ THRD - 6000 ASTM A350 LF2 Cl. 1 11
Flange 2 to 3 4 to 16
RFWN RFWN
80 120 (min)
900 900
ASTM A350 LF2 Cl. 1 ASTM A350 LF2 Cl. 1
3, 12 3, 12
Gasket 2 to 16 RF - 900 Spiral Wound c/w flexible graphite filler and s/s
windings to ASME B16.20 13
Nipple ½ to 1-½ ½ to 1-½
PE, THRD PE, SW
XXS 160
- -
ASTM A333 Gr. 6 SMLS, 100 mm long min ASTM A333 Gr. 6 SMLS, 100 mm long min
8 8
Orifice Flange 2 to 3
4 to 12
RFWN
RFWN
80
120 (min)
900
900
ASTM A350 LF2 Cl. 1, c/w ½” NPT taps
ASTM A350 LF2 Cl. 1, c/w ½” NPT taps
3, 14
3, 14
Plug ½ to 1-½ ½ to 1-½
THRD THRD
XXS -
- 6000
ASTM A350 LF2 Cl. 1, Bull ASTM A350 LF2 Cl. 1, Hex Head
Reducer 2 to 3 4 to 16
BW BW
80 120 (min)
- -
ASTM A420 Gr. WPL6, Conc, Ecc ASTM A420 Gr. WPL6, Conc, Ecc
13 13
Sockolet ¾ to 1-½ SW - 6000 ASTM A350 LF2 Cl. 1 14
Studs & Nuts ALL - - - ASTM A193 Gr. B7, Continuous Thread
ASTM A194 Gr. 2H, 2 Nuts per Stud
Swage ½ to 1-½ SW, THRD - 6000 ASTM A350 LF2 Cl. 1 15
Tee ½ to 1-½ 2 to 3
4 to 16
SW, THRD BW
BW
- 80
120 (min)
6000 -
-
ASTM A350 LF2 Cl. 1 ASTM A420 Gr. WPL6
ASTM A420 Gr. WPL6
9 10
10
Threadolet ½ to 1-½ THRD - 6000 ASTM A350 LF2 Cl. 1 11
Union ½ to 1-½ SW, THRD - 6000 ASTM A350 LF2 Cl. 1 16
Weldolet 2 to 3
4 to 6
BW
BW
80
160
-
-
ASTM A350 LF2 Cl. 1
ASTM A350 LF2 Cl. 1
11
11
TUBING
Component Size (OD) Ends Minimum Wall Thickness Description Notes
Tubing
¼
½ ¾ 1
PE
PE PE PE
0.035”
0.049” 0.065” 0.083”
ASTM A312 316 SS SMLS
ASTM A312 316 SS SMLS ASTM A312 316 SS SMLS ASTM A312 316 SS SMLS
22
22 22 22
VALVES
Component Size NPS
Ends Class Body Trim Type Port Operator Notes
Ball
½ to 1-½
2 3 to 16
THRD
RF RF
1500
900 900
ASTM A350 LF2 Cl. 1
ASTM A352 Gr. LCC ASTM A352 Gr. LCC
Cr PL, TFE
Cr PL, TFE Cr PL, TFE
Split / Floating
Split / Floating Split / Trunnion
RP
RP, FP RP, FP
Lever
Lever Gear
17
4, 18 4, 21
Check ½ to 1-½ 2 to 4
2 to 16
SW,THRD RF
RF
1500 900
900
ASTM A350 LF2 Cl. 1 316 SS
ASTM A352 Gr. LCC
Trim #8 Trim #8
Trim #8
Piston / Bolted Non-Slam / Wafer
Swing / Bolted
RP RP
RP, FP
- -
-
19 5, 21
6, 20
Gate ½ to 1-½ 2 to 16
THRD RF
1500 900
ASTM A350 LF2 Cl. 1 ASTM A352 Gr. LCC
Trim #8 Trim #8
OS&Y / Bolted OS&Y / Bolted
RP RP, FP
Hand Wheel Gear
19 6, 20
Globe ½ to 1-½ 2 to 6
THRD RF
1500 900
ASTM A350 LF2 Cl. 1 ASTM A352 Gr. LCC
Trim #8 Trim #8
OS&Y / Bolted OS&Y / Bolted
- -
Hand Wheel Gear
19 20
Needle ¾ x ½ FNPT x
MNPT 6000 316 SS / 316L SS 316 SS /TFE/V - - - 21
NOTES:
1. Percentage of all butt welds for each welder to be 100% radiographed. 2. All pipe threads shall be in accordance with ASME B1.20.1. 3. Flange face finish shall be Ra 3.2 to 6.3 μm.
4. FP valves to be used in lines that are to be pigged, in flare systems, for block valves on PSVs and on pump suctions that are NPSH critical. 5. For use on compressor discharge and high pressure pump discharge applications. 6. FP valves for use in lines that are to be pigged.
7. ASME B36.10 8. ASME B16.48 9. ASME B16.11
10. ASME B16.9 11. MSS SP-97 12. ASME B16.5
13. ASME B16.20 14. ASME B 16.36 15. MSS SP-95
16. MSS SP-83 17. MSS SP-110 18. API 608
19. API 602 20. API 600 21. Manufacturer’s Standard
22. ASTM A269
